Construction of Olympic Academy at Tiruchirapalli

Amount

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Surface dressing of the ground including removing vegetation ind inequalities not exceeding 15cm deep and disposal of rubbish, lead upto 50m and lift upto 1.5m All kinds of soil

Excavation for roadway in soil using manual means including loading in truck for carrying of cut earth to embankment site with all lifts and lead upto 1000 metres all as per Morth specification 301

Providing Pre - construction Anti - termite treatment and creating a chemical barrier to the building by injecting chemical emulsion of required concentration under grade slab and grade beam, all round the Pile Caps, Catch basins, trenches, pits, tunnels, wall trenches, back fill, plinth filling, junction of wall and floor. External perimeter of building, surrounding of pipes, expansion joints, below U.G. sump and retaining/side walls etc. as per instructions of chemical manufacturer as directed by the Department officer/ Architect. The treatment shall be carried out strictly in accordance with the technical specification and conforming to IS 6313 or equivalent BS specification. The chemical to be used as insecticide for the treatment shall be Biflex Tc, TC stands for Termiticide Concentrate for Termite Control (Bifenthrin) and the application shall be diluted 1 part of chemical Biflex Tc with 49 parts of water to get 0.05% emulsion and strictly in accordance with the manufacturer’s specification.Including cost of chemicals labour charges,transport and storing etc complete and as directed by the department officers

Supplying and filling in foundation, basement, etc with filling sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying filling in foundation,basement etc with filling suitable embankment filler materilas in layers of not more than 15cm thick well watered,rammed and consolidated etc., complete complying with standard specification and as directed by the department officers.

Refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officers in layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification.

Supplying and filling in foundations and the area wherever specified with approved good quality filling materials in plinths, area development etc. wherever specified in layers of not exceeding 150 mm thick including breaking clods, storing, transportation, double handling, watering, compacting each layer with vibratory compactor and at un-accessible places with wooden / steel rammers to achieve 95% proctor density at optimum moisture content, all leads and lifts, bailing / pumping out of water to keep site dry while backfilling cost shall include conveyance of all materials, labour, machinery etc. complete as directed. The rate to includes loading, unloading, hire and fuel charges for tools and plants and other incidental charges etc., complete.

Plain Cement Concrete 1:5:10 (One Cement, Five sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Providing and laying plain cement concrete 1:4:8 using coarse graded aggregate of 40 mm and down size for levelling course under footings, steps, walls, platform etc. including form work wherever necessary and well compacted etc. all complete, as directed.

Cement Concrete 1:3:6 (One Cement, Three sand and Six broken stone jelly) using 10-12mm size hard broken stone jelly for finishing

Damp proof course with Cement Mortar 1:4 (One Cement and Four sand) 12mm thick mixed with best approved quality water proofing compound conforming to Indian Standard specification as specified by the departmental officers at 2% by weight of cement used and finishing, curing etc. complete complying with standard specification.

Cement Concrete M 25 1:1:2 (One Cement, One sand and Two hard broken stone jelly) using 20 mm gauge hard broken granite stone jelly for all RCC items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. shall be finished smooth with Cement Mortar 1:3 (One Cement and Three Sand) and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers

a) Upto basement

b) Ground floor

c) First floor

d)Second floor

Providing and laying in position, Standardised Concrete Mix M-30 Grade in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cementcontent of 400 kg/m3 and maximum water cement ratio of 0.45, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

Upto Basement

Cement Concrete 1:2:4 (One Cement, Two M Sand and Four hard broken stone jelly) using 20 mm gauge hard broken granite stone jelly for all RCC items of works excluding cost of reinforcement grill and fabricating charges, centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. shall be finished smooth with Cement Mortar 1:3 (One Cement and Three M Sand) and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers

Cement Concrete 1:1-1/2:3 (One Cement, One and a half sand and Three hard broken stone jelly) using 20 mm gauge hard broken granite stone jelly for all RCC items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. shall be finished smooth with Cement Mortar 1:3 (One Cement and Three Sand) and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers -Foundation and Plinth

Foundation and Basement

Ground floor

First floor

Second floor

Brick work in Cement Mortar 1:5 using best quality II class Ground moulded chamber burnt bricks of size 9" x 4-3/8" x 2-3/4" for foundation and basement including curing, etc., complete complying with standard specifiction.

Inbetween column Up to plinth level

In ground floor

In First Floor

In Second floor

Brick partition walls of 11.50cm thickness using best quality II Class Table Moulded Chamber Burnt Bricks of size 9" x 4-1/2" x 3" in Cement Mortar 1:3 (One Cement and Three Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

a) Upto basement

b)For Plane Surfaces Such as RCC Floor Slab,Roof slab,Beams,Lintels,Bed Blocks,Landing Slab,Waist Slab,Portico Slabs-Ground floor

c)For Plane Surfaces Such as Rectangular or Square RCC Columns,Sunshades,Top and Bottom slab of RCC Boxing etc

d)Eor Plane surfaces Such as vertical slab, Side slabs of boxing vertical drops Facia vertical wall etc,.

Supplying fabricating and placing in position steel reinforcement using mild steel or ribbed star rods for all RCC works as per the design given including cost of steel and binding wire also in all floors steel and binding wire shall be supplied by the contractors etc., complying with standard specifications.

Stainless Steel (Salem Stainless Steel) Door Frame (Box Section using Stainless Steel Plate of 1.6mm thick) of size 100mm x 60mm with a rebate of 30 / 35mm x 15mm on one side of the frame including supplying and fixing dovetail splayed end stainless steel hold fast etc.,

Overall length

Supplying and fixing the solid core flush door shutters with commercial ply on both side with teak wood lipping alround 35mm thick including cost of furniture fitting such as 3 nos 4"brass butt hinges,2nos 6"brass tower bolts,2nos 4"brass handle, 1 no brass drop, single key shutter, mortice lock without night latch, 1 no door closer, 1 no brass door stopper, 1mm thick best quality lamination sheet etc., complete complying with standard specification.

Providing and fixing Double shutter glass door of 12mm thick plain toughened glass of approved make. The door is fixed by using any approved make hardware fitting like patch fitting, pivot, floor machine, locking arrangements and suitable SS door rails with floral glass etching for 1/3 portion of door area etc complete. The rate includes cost of all materials, labour, hire of tools & machineries, as per the specification.

Providing, fabricating and fixing of stick type structural glazing using Alluminium Extrusions of 63.5 mm x 58.00 mmx 2.25 mm of 1.73 kgs/ mtr for vertical and Horizontal members and 63.5 mm x 38.1 x 1.33 mm of 0.759 kg/Mtr, as outer frame with Electro Anodized Paint coated block finishing, using 6mm thick imported glass reflective hard coatedocean blue raw glass with all necessary accesories like ultra glass Silicon sealant of Space tape, Masking tape, Galvanized Anchaor bolt, machine screws, 6mm thick M.S. angle 50mm x 150mm x 6mm M.S. Galvanized L Brackets, structural sealent setting clocks, fasteners, wall connection etc., complete

Supply and fixing of FRP door Sutter with FRP door frames made out of FRP Sheets of 3mm thick of over all size 65mm x 50mm with rebate suitably reinforced using MS Angle / Flats, cost of holdfasts and solid core FRP shutter Panel of 5mm thick and hollow core frames of 3m wall thickness for styles and rails etc., of sizes specified by Engineers.

UPVC Ventilator Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

UPVC Window Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work (All items rate E674)

Manufacturing, Supplying and fixing of steel doors with the following specification MS angles of a size 40x40x6mm are used for the outer frames and MS angles of size 35x35x5mm for the shutter frames stiffeners with 32x6mm MS flat is provided at required intervals in the shutter frames 18 G CR sheet is laid as panel in the shutter and welded intact. MS flat 18x5mm is welded over the 32x6mm MS flat sand witching the CR sheet in between, Additional stiffener with 18x5mm MS flat is provided diagnonally at the rear side of the shutter, 3 Nos hinges in case of single leaf and 6 nos of hinges in double leaves shutter to be provided 6 nos of holdfasts 120mm in length made of angle section spliced at the ends are welded to the outer frame of the door in single leaf door, one more more aldrop is provided in the inner lock rail section of the door. One rotaining locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door MS flat 32mmx3mm at 1.1Kg/M is provided on the one shutter and conceal the gap between the two shutters at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. all members are given a coat of red oxide primer as directed by the departmental officers. the rate includes cost of all materials , labour charges, taxes, transportation to site of work loading and unloading and all other incidental charges etc complete.

Supplying and fixing of M.S.grill of approved design for open courtyard, grill, grill work to doors and window openings etc., using necessary mild steel flats for inner and outer members which should be fixed on edges including priming coat of best approved quality red oxide primer etc., complete complying with standard specification.

Plastering with Cement Mortar 1:5 (One cement and Five sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Providing 15 mm thick water proof plaster in internal walls(wherever necessary) with Cement Mortar 1:3 (1 cement : 3 Fine sand) with water proofing compound as per IS specification and roughening the surface in green condition with wire brush and clearing of loose particles with sponge brush (washed sand finish)

Plastering with Cement Mortar 1:3 (One Cement and Three Sand) 20mm thick mixed with water proofing compound conforming to BIS at 2% by weight of cement used including finsihing, curing, etc., complete in all floors complying with standard specification and as directed by the departmental officers.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Flooring with following Plain ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Dadooing walls with following best approved quality, white / colour glazed tiles of following sizes set in Cement Mortar 1:2 (One Cement and Two sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers. Dadooing with printed design colour glazed tiles of size 450mm x 300mm x 8mm

Paving the floor with pre-polished concrete anti-skid step tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Manufacturing, supplying and fixing of stainless steel hand rails for staircase using 50mm dia 304L grade stainless steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia stainless steel pipe post of 1.00 mm thick as vertical at 900mm centre with 2 nos of 25 mm dia intermediate horizontal stainless steel pipe of 1.60 mm thick in between. The vertical pipe has to be welded to the 100 x 100 x 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, griding, polishing, conveyance, electrical charges, etc. complete

Paving the floor with best quality Matt finished Anti skid Vitrified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three M Sand) in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with best quality Swimming Pool Glass mosaic Tiles 1"x 1" with (Random Blue Colour Mix Only) with Dubond or Semtro max Tile Adsehive and Dubond or Semtro max Cement based joint gruot materails, complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing and Laying Water proofing for Swimming Pool concrete shell, balancing Tank and pool over flow gutter complete with chemicals & labour(Membrane Method)

Paving the floor with best quality Vitrified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three sand) in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Providing and filling the tile joint with epoxy grout with following specification:Surface preparation including cleaning the joint to be free from dust and loose particles. Providing masking tape on either side of the tile joint edges and providing sealing the tile gap with epoxy tile joint grout and finishing neatly and as directed by the epartmental officers. The rate inclusive of cost of materials and labour, etc., complete.

Providing, mixing, laying polymer based water proofing treatment for the Sunken Toilet / Lift well/ OHT Rcc wall by applying cement based, flexible, waterproofing compound confirming to IS:2645, to a thickness of 1mm of the prepared surface of the roof slab / floor slab as per specifications mentioned above providing cement mortar 1:3, waterproofing cover plaster to a thickness of 12mm over the membrane coating with admixture of approved make. Rate quoted is inclusive of preparation of surface, which includes cleaning of surface polymer mortar curing, labour, tools and equipment, etc. Rate inclusive of grouting with cement and sand required for the treatment, the cost and labour charges for fixing 25mm dia pressure pipes 15kg/cm2 to a length of 45cm for drip pipes, etc. complete.

Providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 (One Cement, Two sand and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers)-For 40mm thick

52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse M Sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Paving the floor with best quality Table Tennis PVC Flooring Brand - Enlio of Thickness - 4.5mm etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with best quality Weight Lifting Tiles of Thickness - 15mm etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Supply & installation of (10+2) mm synthetic PU flooring approved by international basketball/hand ball / badminton /Volleyball federation. Supply and installation of one layer of Conipur 70 primer over concrete /bitumen surface at the rate of 0.15kg/Sqm. Supply and installation of 10mm thick shock pad layer with SBR granules mixed with Conipur 326 binder at the rate of 6 kg per Sqm. Supply and installation of one layer sealing coat with Conipur 220 at the rate of 750gm/Sqm over the SBR Supply and installation of 2mm thick Conipur 227 PU. Supplying and applying of paint coat with approved shade.

Paving the floor with best quality Mat TRENZ-Brand Interlocking System (1mtr x 1mtr x 25mm) JSR+EVA 1 court area 130 sq mtr Density – 130 (kg/m3) Hardness – Shore A (32) etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with best quality Wrestling Mat with Cover Brand -Trenz WFI Approved of Size – 2m X 1m X 60mm Area – 12m X 12m etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Supplying and fixing in position Sports Special type flooring of 25 mm thick using SR paste with necessary cutting including labour charges for fixing in position with neatly etc., complete and as directed by the departmental officers.

Supply and Fixing of 7mm thick PVC Volley ball court FIVB Approved product fixing on Existing Cement flooring including all material labour complete as per specifications and directions of Engineer-in- Charge

Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Nosing for Granite Slab

Supplying & fixing in position Greenlam Sturdo Classique Invincible Toilet Cubicle (of following standard dimension which includes 600mm door size width) made of heat, bacteria, water, chemical, scratch impact and anti bacterial resistant 12mm thick solid compact laminate panels tested by shriram Test House. Finish of the compact laminate should be suede/ *Raw silk, which includes doors, pilasters & intermediate panels finished with approved texture/shade as per the detail drawings & as per IS 2046 (Indian Standard) and as per fire retardant BS-476/97 standard. The product should have Green Guard Certificate. This also includes providing and fixing in position necessary hardware made out of Stainless steel (Grade 304) as per manufacturer’s specifications & Architects instructions like (1) Door Knob, (2) Gravity Hinges, (3) Thumb turn lockset indicators, (4) Coat hooks, (5) U-Channels, (6) SS-Shoe Box Plate (7) MS-Base Plate, (8) Top rail with Corner conntector (9) Rubber noise deafening tape (10) Screws & wall Plugs. The top fitting should consist of SS round top rail which will get fixed with pilasters, with SS panel tube holder, SS corner bend (connected with top rail) will be used on the corner of cubicle in absence of brick wall, SS wall fixing is used only on the wall which will hold the ss top rail. All screws will of 304 Grade in stainless steel with satin finish. All pilasters are supported by stainless steel Bottom Cladding. The base of the stainless steel bottom cladding will be anchored to the floor with a clearance height upto 110mm.

Toilet Cubicle with standard dimension of 2100mm Height x 1000mm Width x 1550mm Depth, which includes 600mm door size width). Toilet Cubicle I-Shape (Front Partition) with standard dimension of 1885mm Height x 1000mm Width which includes 600mm door size width). The divider height to 2100mm height All aspects specified by the manufactures, Greenlam Sturdo Classique Invincible Model or equivalent. complete as per directions of Engineer-in - charge

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Supplying and painting the walls with two coats of wall putty asinstructed by the departmental officers including preparation ofsurface curing, etc., complete in all floors complying with standardspecifications (The wall putty shall be got approved by theExecutive Engineer before use of work).

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting the wall two coats with approved weather proof Exterior Emulsion paint over one primer coat of over cement plastered wallsurface ect., complete complying with standard specification.

White washing two coats with freshly burnt white shell lime in all floors including cost of lime, blue powder fevicol type gum, brushes, scaffolding charges, etc., complete complying with standard specification and as directed.

Colour washing two coats in all floors using best freshly burnt white shell lime and best quality of approved variety of colouring pigment including cost of lime, colouring pigments, fevicol type gum, brushes, scaffolding charges etc., complete complying with standard specification. Mineral colouring pigments not affected by lime should only be used (stainers and colour solutions should not be used.)

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over one coat of red oxide priming coat in all floors including cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Painting new wood work with two finishing coats of synthetic enamel ready mixed paint of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supplying and fixing in position of PVC Coated Chain link fencing 12G 1.5"x1.5" including stiffner wire for fixing top and bottom and tying the fencing to the post with Aluminium binding wire etc complete complying with standard specification.

Providing and fixing of Aluminium Composite Panel(ACP) 4 sided having 50 x 25 x 1.50mm frame work vertical and horizontals out of specially designed extruded sections withstand wind pressure of 180Kg/sq.m and fabricated fixed at all level elevation andheights. The extruded section cutting and fixing required space extruded section shall be of 6063 and alloy of BSH 9 confirming T is – 63400 rate shall included to fix the main frame with necessary clamps,fasteners, bolt nuts etc. The main frame of extruded section shall be of 22843 & 22739 (H9) grade conforming to BS 4174 (or) IS 8147. Rate shall included 4mm thick ACP sheet (0.25 + 3.5 + 0.25) alstrong or equivalent fixing with spacer tape and the ACP sheet bounded with special type structural sealant of dow corning 789 or equivalent in dust free conditions the gaps between ACP sheet to be filed with whether sealant and backer rod or 12mm foam sheet to ensure water and air tightness in all complete complying with standard specification as directed bythe departmental officer

Providing and spreading of high quality weedicide over the prepared surface to avoid the growth of the weeds in the top surface.

Providing granular subbase to required thickness including cost and conveyance of all materials from approved quarry and consolidation by power roller as per clause 401 of Morth specification-

Providing, laying, spreading and compacting graded stone aggregates to Wet Mix Macadam specification including pre mixing the material with water at OMC in mechanical mix plant carriage of mixed material by tipper to site, laying in uniform layer with paver in sub base/base course on well prepared surface and compacting with vibratory roller to achieve the desired density

Providing and applying primer coat over WMM surface using 6 kgs of bitumen emulsion for 10 sqm area including cost and conveyance of bituminous binder including labour charges for preparing the surface and applying the required quantity of bitumen as tack coat by bitumen sprayer etc. complete as per clause 502 of MOST specification

Providing and applying tack coat over PC with WMM surface treated with prime coat using 2.5 kgs of emulsion for 10 sqm area including cost and conveyance of bituminous binder including labour charges for preparing the surface and applying required quantity of bitumen as tack coat by bitumen sprayer etc. complete as per clause 503 of MOST specification

Providing and laying Dense Bituminous macadam 50mm consolidated thickness using 4% of bitumen 60/70 grades per clause 507 of MORTH specification.

Providing and laying Bituminous concrete 25mm consolidated thickness using 5.1% of bitumen 60/70 grade as per clause 512 of MORTH specification.

Providing and fixing precast cement concrete road kerbs of size500x 300 x 150 mm made to shape in C.C.1:2:4 using 20 mm down size Coarse graded aggregate including form work and fixing in base cement concrete 1:3:6 nominal mix laid over sand bed including pointing exposed faces with C.M 1:3 etc. complete, as directed.

'Providing and fixing reinforced cement concrete perforated precast slab with cement concrete 1:1.5:3 for drain cover slab . Rate shall include for providing necessary casting platform, shuttering, reinforcement as detailed below, finishing exposed faces smooth wherever necessary and pointing the joints with C.M 1:3, 15 mm thick curing and fixing in position etc complete and as directed. Rate shall include for providing necessary MS angles of required size based on the thickness of precast slab and to be fixed on the edges of the precast slab including grouting the lugs with Cement concrete 1:1.5:3, GI Hooks for lifting the slab etc complete, as directed for trench covers, drain covers etc.,

Providing and laying in position the RCC humepipes (NP3) of approved quality and make including collars,.necessary Excavation, PCC 1:2:4 supports, Sand cushion of 150mm on all sides, Refilling with earth, Compaction and making good the level, alignment etc.,complete

Supplying, laying and jointing GI pipes of approved quality and best variety of B Class pipes of 100mm dia including labour for laying including earth work excavation, re-filling the trench with excavated earth, sand filling, etc., complete.

Supply and fixing of GI Pipes of following dia with one coat of red oxide primer for fencing post including necessary screws, clamps, welding charges etc complete with standard specification.

50mm dia GI pipe

40mm dia GI pipe

Construction Rain water chamber of 800 x 800mm and average depth of 1.2m in Brick work with II class ground moulded well burnt chamber bricks in cement mortar 1 : 5 , with base concrete 1:5:10 to a thickness of 15cm, plastering in C.M. 1:5, 12mm thick inside and outside, providing channels and slopes, M 25 Precast R.C.C. cover slab 7.5cm thick complete. The rate shall include for necessary excavation, dewatering, refilling, watering, ramming, removing, the surplus excavated material and making good the same complete as required. Cost shall be inclusive of providing,CI manhole cover 600 x 600(Medium duty) with frame.

Supply and fixing of 75x75x6mm Angle ring made up of 75x6mm MS flat with necessary anticorrosive zinc chromite primer with necessary earth work excavation and inserting in the concrete surface and finish neatly etc complete.

Supply and installation of synthetic Atheletic track flooring of IAAF approved make of German make or any other equivalent make and installation and laying as per the manufacuture' specification etc. complete

Providing, laying &jointing in position HDPE pipe conforming to IS: 4985−2000 and suitable for the respective working pressures with all fittings and accessories e.g. couplings, tees, bends, reducers, screwed adapters, flanged tail pieces etc .jointing as per manufacturer's recommendation, including earth work in excavation and refilling (Earthwork includes 450mm of soil cover over the pipe and width of 300mm), complete as per requirement and as per direction of Engineer−in−charge. Captain/Dinesh/Duraline

HDPEPipe160mmOD/PN−10/PE−100

HDPEPipe 110mmOD/PN−10/PE−100

Sprinkler & Accessories :Providing and fixing of Large Radius Popup Sprinkler with Gear driven mechanism having 2" female inlet, dia of coverage 84.0m at 6.0 bars, capable of delivering discharge 15.6 lps and trajectory of throw 25˚.It is suitable for sports fields like Football, Rugby, Hockey, Cricket, Soccer & Baseball. It should have a feature of special internal rubber folding top, avoids the passage of powder, sand and dirty water around the telescopic pipe complete as per requirement and as per direction of Engineer−in−charge. SIME (ITALY), Vyrsa (Spain), Signature (USA)

Providing and installation of Connecting assembly for 2" Pop−up Sprinkler, complete as per requirement and as per direction of Engineer−in−charge.

Providing and fixing of 1.25" two piece aluminum QCV having auto close lid made of heavy duty rubber when QCV is not in use, onepiececonstruction,havingstainlesssteelspring,br assvalves,complete as per requirement and As per direction of engineer−in−charge. Harit (India), Aqua (India), Irritech (Italy)

Providing and fixing of 1.25" Steel QCV Key with handle, complete as per requirement and as per direction of Engineer−in−charge. Harit (India), Aqua (India), Irritech (Italy)

Providing and fixing of 1" One piece Brass QCV having auto close lid made of heavy duty rubber when QCV is not in use, one piece construction, having stainless steel spring, brass valves, complete as per requirement and as per direction of Engineer−in−charge. Harit (India), Aqua (India), Irritech (Italy)

Providing and fixing of 1" Brass QCV Key with handle with 1" outlet, complete as per requirement and as per direction of Engineer−In-Charge Harit (India), Aqua (India), Irritech (Italy)

Providing and fixing of 1" Brass QCV Key Brass swivel elbow, complete as per requirement and as per direction of Engineer −in− charge. Harit (India), Aqua (India), Irritech (Italy)

Providing and fixing of Metallic Service Saddle 110mm x 1.25", complete as per requirement and as per direction of Engineer−in−charge.

Providing and fixing of Metallic Service Saddle 110mm x1", complete as per requirement and as per direction of Engineer−in−charge

Valves & Accessories :Providing and fixing of 6" Butterfly Valve for Isolation. It shall be with integral synthetic rubber lining. It shall be lever operated quarter turn and offers bi−directional smooth operation. The hydraulic body test pressure of the cast iron buffer type Butterfly Valve is 15 bar and hydraulic seat test pressure of the product is 11bar complete as per requirement and as per Direction of Engineer−in−charge. Zoloto, Leader, Sant

Providing and fixing of 20" Rectangular Valve Box with cover. The valve boxes shall be high strength, high density polyethylene constructed material. It should be UV stabilizer with antioxidants, resistant to moisture, complete as per requirement and as per direction of Engineer−in−charge. MAIS (KSA), Carson (USA), Palaplast (Greece)

Providing and fixing of 6" Round Valve Box with cover. The valve boxes shall be high strength, high density polyethylene constructed material. It should be UV stabilizer with anti oxidants, resistant to moisture, complete as per requirement and as per direction of Engineer−in−charge.Armas (Turky), Aqua (India), Bermad (Israel)

Providing and fixing of Glass Reinforced Polyamide 2' size quick pressure relief valve. The maximum working pressure shall be 10 bar. Armas (Turky), Aqua (India), Bermad (Israel)

Providing and fixing of a double acting Continuous Air release cum vacuum relief valve2" made of Aluminum. The Continuous Air release valve shall be capable of both releasing and admitting air from and into the line during system operation. The working pressure shall be 10 Bars and testing pressure shall be 16Bars, complete as per requirement and as per Direction of Engineer−in−charge.Harit (India), Aqua (India), ARI (Israel)

Providing and fixing of double acting Air release valve 2" made of high strength plastic with fiber glass reinforced. The Air release valve shall be capable of both releasing and admitting air from and into the line during system operation. The working pressureshallbe10Bars and testing pressure shall be 16 Bars, complete as per requirement and as per direction of Engineer−in−charge. Harit (India), Aqua (India), ARI (Israel)

Filtration Unit :Providing and fixing of Disc filter (120 mesh) 50m3/hr having an inlet & two outlets connections of 3", 2 pressure gauze ports of 3/4", a helix made of fiber glass reinforce polyamide at base of disc filter cartridge to create a helical effect in the incoming water , spinning particulate in suspension away from the filtering element and so minimizing cleanings frequency ,3/4" outlet for flushing at bottom of filter & maximum working pressure of 14bars, complete as per requirement and as per direction of Engineer−in−charge. Harit (India), Arkal (Israel), Amaid (Israel)

Providing and fixing of SS Pressure Gauge (Glycerin filled), complete as per requirement and as per direction of Engineer−in−charge. Make: Wika, Fiebig, Guru, Automat (India)

Providing and fixing of 6" header assembly made of MS pipe with powder coating including foot valve, complete as per requirement and as per direction of Engineer−in−charge. Make: Wika, Fiebig, Guru, Automat (India)

Automation Unit :Providing and fixing of 3" BSP Straight flow Solenoid valve with flow control which shall be normally closed 24 VAC 50/60 cycle solenoid actuated angle pattern design. The valve pressure rating shall not be less than 10.5 bar. The valve body shall be constructed of high impact, weather−resistant Nylon Glass Filled with heavy duty diaphragm and stainless steel screws, fasteners and components. The valve shall have manual open/close control (internal bleed) for manual opening and closing of valve without electrically energizing the solenoid, manual bleed can be removed for "tamper proof" operation. The valve shall operate with minimum 24 VAC at 10.5bar. The valve must open or close in less than 1 minute at 10.5 bar, and less than 30 seconds at 0.7 bar. The valve construction shall provide for all internal parts to be removable from the top of the valve without disturbing the valve installation, complete as per requirement and as per direction of Engineer −in−charge. HIT (USA), K-Rain (USA), Rain-Spa (Itely)

Providing and fixing of DBR Connectors. It shall be pre filled, low voltage, dry splice, Direct Bury, water proof wire connector that protect electrical connection from corrosion and moisture. Each splice Kit contains Two wire nuts, water proof, Gel−filled housing and 1 dual splice organizer complete as per requirement and as per direction of Engineer −in−charge. HIT (USA), K-Rain (USA), Bermad (USA)

Providing and fixing of 1.5sq. mm single core copper conductor cable 24 volt in the existing conduits, complete as per requirement and as per direction of Engineer−in−charge. Finolex (India), Empire (India), Havel (India)

Providing and fixing of 16 sq. mm triple core copper conductor cable 24 volt in the existing conduits, complete as per requirement and as per direction of Engineer−in−charge. Finolex (India), Empire (India), Havel (India)

Providing and fixing of PVC Conduit Pipe 32mmdia for laying of electric wires on surface/ cable tray etc, complete as per requirement and as per direction of Engineer−in−charge. AKG (India), Finolex (India), Supreme (India)

Providing and fixing of 6 Station Outdoor Controller.HIT (USA), K-Rain (USA), Orbit (USA)

Providing and fixing of Pump Start Relay complete as per requirement and as per direction of Engineer−in−charge. K-Rain (USA), PLA (India), Siemens (India)

Providing and fixing of Constant Voltage Transformer (CVT) for controller.

Providing and fixing of automatic controller with single key start. Automat (India), Havels (India)

Providing and fixing of water level sensor. Automat (India), Havels (India)

Levelling and filling football ground in to the suitable gradient, applying water to the ground and allow for 3 days, after15 days, removing any vegetation or grass, or wild grass growth if necessary and thoroughly mixing the earth and leveling to the required gradient etc completely and as directed by the SDAT officers.

Supplying and conveying the soil mixtures of red soil, savudu of good quality and manure in the proportion of 25%, 50% and 25% respectively, and thoroughly mixing, and depositing to a average depth of 3” in the football ground to a gradient specified including cost of red soil, savudu and manure etc complete as directed by the SDAT officers.

Supply and filling with Conveyed earth suitable for natural turf forming except clayey soil and stoney earth including levelling and manual compaction etc complete as directed by the departmental officers.

Pre-Engineered Buildings - Supply, Fabrication, Erection with Labours, Consumables, Power tools, Toggles, crane and Painting of Steel structures - Two coats of Zincromate Primer + One coat of Enamel Paint.

Supply and Fixing of Standing Seam Roof and Wall Cladding sheets with 0.55 MM THICK TATA Bluescope , AZ150, 300-340MPA , 430:MM Effective width including all materials labourt Etc as per Direction of Architect and Engineer Incharge

Supply and fixing of Pre-fabricated Structural Steel, coated galvalume ROOFING SHEET of 0.5mm thickness with SMP coating with colour bond XRW coating, having minimum of 550 Mpa yield strength, Coating 150 GSM as per ASTM 792 or equivalent standard. The structural roofing Panel shall have 1020 mm effective width, nominal 30 mm crest height at nominal 250 mm centre to centre pitch with the embossment (share grove) on top & side of ribs for better composite action including Flashing for joints, and all incidental charges

Supply,fixing and installation of precast boundary wall having height 2.4 metres,length of 3 metres,wall thickness of 5 inches and column thickness of 18 inches.the precast wall is M30 Grade concrete reinforced with a 12mm rebar ,steel fibers and polypropylene fibers including all works etc as per direction of architect and engineer incharge

Supplying and fixing in position white/ colour special delux model glazed cascade type paryware/Hindware/Equivalent wall mounted European water closet of best quality and approved make with 100mm "P" or "S" trap connecting with CI pipe of 100mm dia/ PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing,spun yarn, teak wood plugs,brass screws, etc., including supplying and fixing 10 litres capacity PVC/12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball value with polythene float with brass handle, union cuppling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings, such as, 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 nos), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works)with 10 litres capacity flushing tank with all internal dual flush fittings with normal seat cover.Wall Fitting

Wash Hand Basin of size 550mm x 400mm with all accessories such as Cast Iron Brackets, 32mm dia CP Waste Coupling, Rubber Plug and Chain, 32mm dia 'B' Class GI Waste Pipe, 15mm dia GM Wheel Valve,15mm dia Nylon Connection, 15mm dia Brass Nipples, 15mm CP Pillar Tap etc Without Pedestal

Supplying, fixing, testing and commissioning approved make Urinal with piller cock fixed above counter with 32mm dia CP waste coupling, 32mm dia C.P.bottle trap with C.P. extension pipe, 1 No. C.P. flexible inlet connection pipe G.I. expansion bolts etc., complete including silicon sealant.

Supplying, fixing, testing and commissioning of approved make 15mm CP Concealed Stop cock with one no, CP flexible tube 1.0m long, CP crutch, nozzle etc., complete.

Supplying, fixing, testing and commissioning approved make 15mm CP CP Two Way Bib Cock with Health Faucet with one no, CP flexible tube 1.0m long, CP crutch, nozzle etc., complete.

Supplying, fixing, testing and commissioning approved make Mirror 600X450 with necessary fixing screws etc complete.

Supplying, fixing, testing and commissioning approved make Angle valve with necessary fittings.

Supplying and fixing best quality of C.P. wall mixer ,over head showerarm with rose and necessary fittings etc complying with standard specification..

Supplying and fixing in position UPVC specials / Pipe of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

a) 40 mm dia UPVC Pipe

b) 50 mm dia UPVC Pipe

Dia 40mm UPVC Elbow

Dia 50mm UPVC Elbow

Dia 40mm UPVC BEND

Dia 50mm UPVC BEND

Dia 40mm UPVC TEE

Dia 50mm UPVC TEE

Dia 50mm X 40 mm UPVC REDUCER

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

A) 75 mm dia PVC pipe

B) 110 mm dia PVC pipe

B) 160 mm dia PVC pipe

Dia 75 mm PVC Elbow

Dia 110 mm PVC Elbow

Dia 75 mm PVC SHOE

Dia 110 mm PVC SHOE

Dia 75 mm PVC Y

Dia 110 mm PVC Y

Dia 75 mm PVC Tee with Single Door

Dia 110 mm PVC Tee with Single Door

Dia 75 mm PVC Bend

Dia 110 mm PVC Bend

Supplying, laying, jointing, testing and comissioning of approved make PVC floor trap with C P grating with required concrete encasing all around, complete.

a) 110 x 75 mm dia (20 mm water seal)

RAIN WATER SYSTEM: Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

110mm dia PVC Pipe

Dia 110 mm PVC Elbow

a) 110 mm dia

a) 160 mm dia(soil pipe)

Supplying, fixing, testing and commissioning of glazed stoneware gully traps, 550x550mm C.I. grating (medium duty), 100 mm dia outlet set in PCC 1:4:8 bed, 115 thick masonry chamber in CM 1:4, internal and external plastering 12mm thick in CM 1:6, necessary earthwork, C.I. cover (medium duty) etc., complete.

Providing and constructing inspection chambers comprising burnt brick/solid block masonry walls of 230 mm thk., built in CM 1:4 over M-15 CC bed of thickness 100 mm, benching in CC M-15, internal faces plastered smooth in CM 1:4, 15mm thick and outside Rough Plastered with CM 1:6, 15mm thick including necessary earth work excavation returning and refilling and disposing surplus soil as directed by the Engineer in charge.

a) 600 x 600 mm size internal and depth more than 450 mm but not exceeding 850 mm

b) 600 x 600 mm size Heavy duty cover

Supplying and fixing PVC foot steps

HGS SS.20.B. Earth work excavating and depositing on bank with initial lead of 10 m & initial lift of 2m in Hard stiff clay, stiff black cotton, hard red earth, shales, murram, gravel, stoney earth and earth mixed with small size boulders SS.20B

Supplying, laying and jointing PVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing PVC specials using PVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works.

dia 20mm PVC pipe

dia 25mm PVC pipe

dia 32mm PVC pipe

Dia 20mm PVC ELBOW

Dia 25mm PVC ELBOW

Dia 32mm PVC ELBOW

Dia 20mm PVC TEE

Dia 25mm PVC TEE

Dia 32mm PVC TEE

Dia 20mm PVC COUPLER

Dia 25mm PVC COUPLER

Dia 32mm PVC COUPLER

25 mm x 20 mm PVC REDUCER

32 mm x 25 mm PVC REDUCER

40 mm x 32 mm PVC REDUCER

Supplying, laying and jointing PVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing PVC specials using PVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works.

dia 40mm PVC pipes

Dia 40mm ELBOW

Dia 40mm COUPLER

Dia 40mm TEE

40 mm x 32 mm REDUCER

a) 32 mm dia uPVC Schedule 80 Pipe ( UG SUMP TO OH TANK)

a) 40 mm dia uPVC Schedule 80 Pipe

a) 50 mm dia uPVC Schedule 80 Pipe

Dia 32mm UPVC ELBOW

Dia 50mm UPVC ELBOW

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

Dia 25mm Gun Metal Wheel Valve

Dia 32mm Gun Metal Wheel Valve

Providing and placing on terrace Polyethylene water storage Tanks as per IS 12701 : 1996 with manhole lid and suitable locking arrangements, making holes of suitable diameter for inlet, outlet and overflow pipes, including cost of all materials, labour transport charges, HOM and testing complete as per specifications.

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points / Coil) Higher End )( SD - 281 )

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling and switch drop portion PVC rigid pipe concealed with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate continuous earth wire connection by 1.5 sq.mm copper wire with painting of suitable colour for PVC Light point / fan point (for electronic regulator) ( 4 points / Coil) Higher End )

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling and switch drop portion PVC rigid pipe concealed in wall with PVC accessories with Module GI switch box in flush wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire with painting of Suitable colour for Open PVC Light point / fan point (for electronic regulator) ( 5 points / Coil) Higher End )

Supply and fixing of WT bulk head fitting with guard suitable for with 7W/9W LED bulb.

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points / Coil) Higher End )

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (6 points / Coil) Higher End

Wiring with 3 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A two way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC pipe Stair case Light point Higher End

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with suitable Module GI switch box in flush with wall with 1 no. 6A one way module switch and 1 no. 6A 3/2 pin module socket with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with painting of suitable colour for concealed PVC pipe Plug point ( 8 points / Coil) Higher End

Supply and fixing of 30W LED 2' x 2' Square Types Surface mounted fitting with LED complete with electronic balleast with TW round block on wall or ceiling with PVC unsheathed Copper leads from terminals to the fitting.

Supply and fixing of 18W LED Round Types Surface mounted fitting with LED complete with electronic balleast with TW round block on wall or ceiling with PVC unsheathed Copper leads from terminals to the fitting.

supply and fixing of 24W LED 2x2 square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of single box type 4' 20W LED fitting with LED tube complete with TW round blocks on wall or ceiling with PVC unsheathed Copper leads from terminals to the fitting.

Supply and fixing of single box type 4' 20W LED fitting with LED tube complete with electronic ballast with conduit pipe suspension from the ceiling with PVC unsheathed copper leads from terminals to the fitting with tube.

Supply and fixing of 28W linear fitting [Model No.CCP-121-28-WW/TL/CDL-SL-NWH / Crompton make] for 28W 4' with its minimalistic shape complete with electronic balleast with TW round block with conduit pipe suspension from the ceiling with PVC unsheathed Copper leads from terminals to the fitting.

Supply and fixing of 80W LED Highbay light fitting [Model OPTIBAY 80W WH NB PC SD] with integrated driver with PDC housing with IP66 protection, heat resistance tempered glass for protection with 4KV inbuilt Surge protection on the existing angle iron frame work with PVC unsheathed leads with painting of suitable colour

Supply and fixing of 150W LED Flood light fitting [Model PRAZE 180L WH NB-A5 TG SD] with integrated driver with PDC housing with IP66 protection, heat resistance tempered glass for protection with 5KV Surge protection on the existing angle iron frame work with PVC unsheathed leads with painting of suitable colour for focusing of approach road.

Supply and fixing of 180W LED Flood light fitting [Model PRAZE 216L WH NB-A5 TG SD] with integrated driver with PDC housing with IP66 protection, heat resistance tempered glass for protection with 5KV Surge protection on the existing angle iron frame work with PVC unsheathed leads with painting of suitable colour for focusing of approach road.

Supply and fixing of 12W LED Square Types Surface mounted fitting with LED [Model No.BGSLO SLEEK SURFACE 12W WH SQ LED ] complete with electronic balleast with TW round block on wall or ceiling with PVC unsheathed Copper leads from terminals to the fitting.

Supply and fixing of 36W LED Square Types Surface mounted fitting with LED [Model No. BZSSQL 36L LED WH GX MT ] complete with electronic balleast with TW round block on wall or ceiling with PVC unsheathed Copper leads from terminals to the fitting.

Supply and fixing of 45W LED Square Types Surface mounted fitting with LED [Model No. BZSSQL 45L LED WH GX MT ] complete with electronic balleast with TW round block on wall or ceiling with PVC unsheathed Copper leads from terminals to the fitting.

Supply and fixing of 150W Highbay LED light with integrated driver with PDC housing with IP66 protection, heat resistance tempered glass for protection with 4KV Surge protection on the existing angle iron frame work with PVC unsheathed leads with painting of suitable colour

Supply and fixing of Mirror light 20W LED Battern complete [ with on wall with PVC unsheathed FRLS Copper leads from terminals to the fitting.

supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting .

supply and fixing of 1200mm (48") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher end) with 600 mm down rod with fan clamp with side plates and cross arm of size 450mm (18")

Supply and fixing of 1400mm (56") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher end) with 1 metre down rod on the existing fan clamp [SD-488]

Supply and fixing of 200 mm sweep AC exhaust fan complete [Havells Model Ventil Air Hush Steel Finish] with necessary wall opening and making good of the wall

Supply and fixing of 400mm sweep Wall Mounting Fan [Usha / Crompton /Almonard make] complete on wall with necessary connection

Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete without provision of hole in the wall .

Supply and fixing of louvers shutters arrangements for 300mm (12") sweep (light duty) AC exhaust fan

Supply and fixing of 1 no.6A two module 5 pin socket , 1 no. 6A one module switch on suitable module surface mounting Box (GI ) with module cover plate (plastic) on wall with connections. Higher End

Supply and run of 2 of 1.5 sqmm (22/0.3) PVC insulated SC unsheathed FRLS copper Conductor of 1100V grade in suitable gauge M.S. conduit pipe on wall and ceiling with continuous earth wire connection of 1.5 sq.mm copper wire with painting of suitable colour.

Supply and fixing of 3 nos.6A two module 5 pin socket , 3 nos. 6A one module switch on suitable module surface mounting Box ( Plastic ) with module cover plate (plastic) on wall with connections. Higher End

Supply and Run of 2 of 2.5 sq.mm PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable gauge MS conduit pipe on wall and ceiling with continuous earth wire connection of 2.5 sq.mm copper wire with painting of suitable colour.

Supply and fixing of 3nos.6A two module 5 pin socket , 3 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and Run of 2 of 2.5 sq.mm PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable gauge MS conduit pipe Concealed in wall and ceiling with continuous earth wire connection of 2.5 sq.mm copper wire and making good of the concealed portion with suitable colour

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch on suitable module surface mounting Box (GI ) with module cover plate (plastic) on wall with connections. Higher End

Supply and Run of 2 of 4 sq.mm PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection by 4 sq.mm. PVC insulated SC unsheathed copper wire with painting of suitable colour.

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and Run of 2 of 4 sq.mm PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 4 sq.mm copper wire and making good of the concealed portion.

Supply and fixing of Weatherproof cabinets - IP 65 - IK 09 - Class II Door and cabinet fully reversible Removable chassis and faceplates 32A FP MCB in flush with wall and making good of the concealed portion with earth connection. (Legrand make Model No.6018 84).

Supply and fixing of brass cable gland 4 x 10 sq.mm PVC armoured LTUG copper cable with earth connection.

Supply and clamping of 4 Core x 10 sq.mm PVC Copper LTUG cable on post or on wall with MS clamps.

Supply and providing cable end termination of 4 x 10 sqmm PVC LTUG Copper armoured cable with necessary copper cable sockets by crimping etc. with electrical connection complete

Supply and fixing of 7 segment 4 way 63A TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB and another seperate 4 way provision for accomodating 3Nos. 2 pole ELCB / RCD (3x 4 ways in each segment) and seperate provision for MCB / Isolators ( totally 12 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following in flush with wall with earth connection only. Higher End i. 63A FP MCB -1No (As incoming), ii. 63 Amps 30 MA DP RCCB -3Nos, iii. 6A to 32A SP MCB -12 Nos

Supply and fixing of brass cable gland 4 x 16 sq.mm PVC armoured LTUG copper cable with earth connection.

Supply and clamping of 4 Core x 16 sq.mm PVC Copper LTUG cable on post or on wall with MS clamps.

Supply and providing cable end termination of 4 x 16 sqmm PVC LTUG Copper armoured cable with necessary copper cable sockets by crimping etc. with electrical connection complete .

Supply and fixing of 7 segment 6 way 63A TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB and another seperate 4 way provision for accomodating 3Nos. 2 pole ELCB / RCD (3x 4 ways in each segment) and seperate provision for MCB / Isolators ( totally 18 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following in flush with wall with earth connection only. Higher End ( i. 100 A FP MCB -1No (As incoming) ii. 40 Amps 30 MA DP RCCB -3Nos iii. 6A to32A SP MCB -18 Nos

Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 100 A 4P MCB Isolator as incoming and 3 nos. 63A 3P MCB , 3 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Higher End

Supply and fixing of brass cable gland for 4 x 25 sq.rnrn LTUG armoured cable with earth connection.

Supply and clamping of 4 Core x 25 sq.mm PVC Copper LTUG cable on post or on wall with MS clamps.

Supply and providing cable end termination of 4 x 25 sqmm PVC LTUG Copper armoured cable with necessary copper cable sockets by crimping etc. with electrical connection complete .

Supply and installation, testing and commissioning of 250 KVA Water Cooled Diesel Generator set with AMF Panel as per Technical specifications. A) DIESEL ENGINE:- KIRLOSKAR" Make diesel engine Model 6SL90ETA 4G2, Six Cylinders, liquid cooled, turbocharged with after cooler, developing 310 bhp @ 1500 RPM., electric start, compression ignition, 4 strokes, designed to run continuously at 1500 RPM confirming to IS 10002, ISO-3046, BS 5514 standard. Diesel Engine will comply with present CPCB IV + norms. The diesel engine will comprise of following with KG-1500 Control Panel 1. Dry type air cleaner 2. Exhaust Silencer suitable for canopy 3. Expansion bellow 4. Lube Oil cooler 5. Lube oil filter 6. Fuel Filters7. Radiator with pusher type fan and mounting 8. In-line mono block fuel injection pump 9 Electronic governor and fuel feed pump 10. Flywheel with starter ring and bell housing suitable for close coupling 11. 24 Volt electric starter motor 12. Battery charging alternato 13. Microprocessor based KG745 Controller mounted on the Controller Panel 14. Protection System for Low lube oil pressure High water temperature

B) ALTERNATOR:- KIRLOSKAR GREEN" make 250 kVA Alternator, suitable for continuous operation rated at 1500 rpm 415 V, 0.8 PF, 50Hz, 3Ph. in SPDP enclosure, self- excited & self- regulated, Brush less, floor mounted with Ball or Bearings on end shields. The alternator conforms to IS: 4722, BS EN 60034-1& will be suitable for tropical condition C) BASE FRAME:- Suitable to couple above Engine & Alternator made from steel sheet metal. D) FUEL TANK:- 600 litre capacity,with Inlet & Outlet arrangement, air vent & drain plug arrangement. E) BATTERIES:- 24 Volts Battery with one set of connecting leads of 70sq mm Size Copper Cable. F) CANOPY DIMENSION IN (mm):- [L: 4750 W: 1700 H: 2005 ] (G) DG SET WEIGHT (Approx):- 250KVA- 3990 Kg Dry Weight 4100 Wet weight H) STANDARD GENSET CONTROLLER UNIT WITH CONTROL PANEL:- Genset controller unit ‘KG - 745’ with totally enclosed, steel construction canopy in build control panel having following safeties and display parameters: Engine Display parameters 1) Oil Pressure 2) Engine coolant Temperature 3) Fuel Status 4) Engine speed 5) Engine run Hours 6) Total starts 7) Battery condition monitoring Mechanical Safeties (along with Display) 1) Under/Over speed 2) Low Lube oil pressure 3) High engine coolant temperature 4) Charge Alternator fail 5) Start/Stop fail Gen-set Display Parameters 1) Phase/Line Voltage 2) Line current 3) Frequency 4) Average Voltage 5) Average Current/Percentage of load 6) Phase kW & Total kW 7) KWH / PF 8) KVA / KVA 9) Earth fault Current 10)DG contactor Manual ON/OFF, Electrical Safeties (along with Display) 1) Genset Under/Over voltage 2) Under/Over Battery voltage 3) Under/Over frequency 4) Phase Failure 5) Phase sequence reverse 6) Over Current 7) Over kW 8) High Earth Current 9) Mains Monitoring 10)Mains contactor Manual ON/OFF

TECHNICAL SPECIFICATION OF KIRLOSKAR GREEN ACOUSTIC ENCLOSURE CONSTRUCTION: Following are some technical features of Acoustic Enclosure:- 1. The enclosure is modular in construction, 2. Base frame is made of Sheet metal, 3. Durable industrial locking system is provided on doors. 4.Doors are gasket with high quality EDPN material. CORROSION RESISTANCE:-To make the enclosure weather proof: - 1. All sheet metal parts/components are hot dipped in seven tanks process, pretreated and passivated. 2. Sheet metal components are painted with P.P base power. 3.Base frame is epoxy coated . 4. Zinc passivated hardware is used to avoid rusting ACOUSTIC INSULATION:- 1. Sound proofing of the enclosure done with quality Foam confirming to IS: 8183. 2. Acoustic form shall be fire retarded and fire resistant. 3. Attenuates are provided to control sound at entry and exit to and from the container.4. Specially designed Residential Silencer is provided. ELECTRICAL:- Neutral earth connecting point at termination block / neutral bus at control panel & Body earthing points at alternator leg and acoustic enclosure base frame., SOUND LEVEL:- The Genset being offered comply to a sound level of < 75 dbA (12 point average) at a distance of 1-meter in free field conditions conforming to CPCB Norm. WARRANTY:-The warranty is for 24 months from commissioning or 5000 hours of operation whichever is earlier, subject to use

Supply and fixing of brass cable gland for 3 1/2 x 150 sqmm PVC armoured LTUG cable with earth connection.

Supply and clarnping of 3 1/2 x 150 sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps.

Supply and providing cable end termination of 3 1/2 x150 sqmm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete.

Supply and erection of 400 Amps Capacity dust and vermin proof floor mounting cubical panel board fabricated out of 16 SWG CRCA sheet for outer body, stiffness and doors and with supply and fixing of following interior switches with centre bus bar chamber and vertical no of switches one over the other on both sides of bus bar chamber with cable adopter chamber of the extreme end of one side with two coats of quality paint over one coat of zinc oxide primer superscription of incoming and outgoing feeding cable details, capacity of switches etc., with white paint and 2 nos metallic danger board affixed complete on base channel supports to satisfy the latest CEIG rules with the following switches confirming to IS specifications. 1] 400A TPN switch disconnector fuse interior only with HRC fuses double break - 2Nos [L & T / Siemens] and interconnection with 3 phase and neutral bus bars using 2" X 1/4" copper flat 3]250A TPN switch disconnector fuse interior only with HRC fuses double break- 3Nos [L & T / Siemens] and interconnection with 3 phase and neutral bus bars using 1" X 1/8" copper flat 3]200A TPN switch disconnector fuse interior only with HRC fuses double break- 3Nos [L & T / Siemens] and interconnection with 3 phase and neutral bus bars using 1" X 1/8" copper flat

Supply, Erection of 400A LTCT Pedestal Type Cubical Panel Board Using LTCT metering box as per IE rules and TANGEDCO Norms (above 150 HP below 200 HP) 112-150 KW made up of 16 SWG CRCA Sheet of Suitable Length for Outter, Inner and Cross Sections of the Chambers on Suitable Angle iron Frame work with Vermin and Dust Proof with 50mm X 6mm Tinned insulated copper Bus Bars for three Phases and Neutral with Suitable Size Hylum Sheet Seperations and Interconnections made up of 4sq.mm. (56/0.3) wire for the CT Coils with the Bus Bar phases and Neutral with Danger Board The LTCT Panel Board Should be Erected on a Suitable Pedestal with Foundations Bolt & Nuts with 1 Coat of Red Oxide and 2 Coats of Synthetic Enamal Paint with Testing,Transportation and Commissioning Etc., with Following Accessories. |400A/5A CT Coils Kappa Make - 3 Nos |HRC Fuse Links - 3 Nos( WD-M-2034 )

Supply and fixing of brass cable gland for 3½ x 240 sqmm PVC armoured LTUG cable with earth connection

Supply and laying of 3 ½ x 240 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 mt. Layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good.

Supply and clamping of 3 ½ x 240 sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps.

Supply and providing cable end termination of 3½ x 240 sqmm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete .

Cable Trays & MS Supports :Supply & installation of Hot -dip galvanized cable rack system made of 2mm thick sheet steel folded with two longitudinal side rails connected by rungs at regular intervals of following sizes with necessary Tee's, Vertical/ Horizontal Bends, expansion anchor fasteners, coupler plates, coupling fasteners, including supply & grouting of supports as required at site. The supports should be painted with black enamel paint over a coat of anti corrosive primer. (Tray shall be measured along the central axis of the cable tray, 1000mm above sizes are fabricated by MS items)

600mm width Ladder Tray 100mm Height

450mm width Ladder Tray 50mm Height

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection.

Supply and fixing of 3 nos.6A two module 5 pin socket , 3 nos. 6A one module switch on suitable module surface mounting Box ( Plastic ) with module cover plate (plastic) on wall with connections. Higher End

Supply and fixing of 3nos.6A two module 5 pin socket , 3 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and Run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 2.5 sq.mm copper wire and making good of the concealed portion

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End.

Supply and fixing of 32A DP MCB in sheet steel enclosure in flush with wall and making good of the concealed portion with earth connection. (The FP MCB and metal enclosure should be with Higher End make.

Supply and fixing of 32A DP MCB in sheet steel enclosure in flush with wall and making good of the concealed portion with earth connection. (The FP MCB and metal enclosure should be with Higher End make.

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and Run of 2 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 4 sq.mm. PVC insulated SC unsheathed FRLS copper wire and making good of the concealed portion

Supply and fixing of 7 segment 4 way TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 4 ways in each segment) and seperate provision for MCB / Isolators ( totally 12 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following on wall with earth connection only i. 63A 4P MCB - 1 no. ii. 63A DP MCB Isolator -3 nos. iii. 6A to 32A SP MCB - 12 nos.

Supply and fixing of 4 way Vertical Triple pole and neutral MCCB sheet steel enclosure distribution board ( with MCCB Incomer ) with double door (metal door ) with 1 no. 125 A 4 P MCCB switch as incoming and 2 nos. 63A 3P MCB , 6 nos. 6A to 32A SP MCB as outgoing with suitable cable end box on wall with earth connection only. [Higher End] i. 125 A 4P MCB - 1 no. ii. 63A DP MCB Isolator -3 nos. iii. 6A to 32A SP MCB - 3 nos.

Supply and fixing of 8 way Vertical Triple pole and neutral MCCB sheet steel enclosure distribution board ( with MCCB incomer) with double door (metal door) with 1 no. 160A 4P MCCB switch as incoming and 4 nos. 63A 3P MCB, 6 nos. 6A to 32A SP MCB as outgoing with suitable cable end box in flush with wall with earth connection.only. Higher End i. 160A 4P MCB - 1 no. ii. 63A DP MCB Isolator -8 nos.

Supply and fixing of brass cable gland for 3 ½ x70 sqmm PVC armoured LTUG cable with earth connection.

Supply and fixing of brass cable gland for 3½ x 95 sqmm PVC armoured LTUG cable with earth connection.

Supply and laying of 3 ½ x 95 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 mt. Layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good.

Supply and laying of 3 ½ x 70 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 mt. Layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good.

Supply and clamping of 3 ½ x 95 sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps.

Supply and clamping of 3 ½ x 70 sq.mm PVC LTUG armoured LTUG cable on post or on wall with MS Clamps

Supply and providing cable end termination of 3 ½ x 70 sqmm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete

Supply and providing cable end termination of 3 ½ x 95 sqmm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete

Earthing as per the ISI specification with an earth electrode of 2.1mt class 'B' GI pipe of dia not less than 40mm, with copper earth plate of size 125mm x 50mm x 6mm, with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry .

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection

Design, supply, erection, testing, commissioning and handing over of 16 mtrs High Mast Structure with required number of continuously tapered hot dip galvanized steel polygonal sides sections with telescopic strip joints to a total height of 16 meters capable of sustaining the maximum wind pressure at the erection site with single flange base plate secured welded in the bottom of the base mast section with vertically movable hot dip galvanized lantern carriage and accessories such as electrical junction box brackets for providing 8 Nos. of flood light luminaries with control gear box complete head frame assembly, Pulley drive, stainless steel wire rope single/double drum self-lubricating winch arrangement suitable for raising and lowering the luminaries carriage ring flexible multi core power cable and necessary high tensile hot dipped galvanized foundation, bolt & nuts along with washers and anchor plates and templates including supply and fixing the following accessories in the Mast.a) Design and casting of suitable foundation with 1:2:4 mix RCC concrete with 30 cm projection above the ground level with 1 metre Width x 1 metre Length and 2 metre depth with necessary galvanized foundation bolts nuts and washers and dump plate enclosing the bolts for the High Mast considering the safe soil bearing capacity at site - 1 set.b) High powered power tool complete with hand held control panel and motor with push button type remote control switch suitable for 3 phase 415 V 50 HZ for raising and lowering of the lantern carriage complete to operate all fittings mounted in the base to couple with winch - 1 Set c) Feeder pillar box comprising 0.90 m x 0.45m x 1,20m floor AI frame with 63 A TPN main switch 1 no , 63 A fuse unit 3 nos. 63 A power contactor with automatic timer arrangements and reversing starter for the 3 phase motor - 1 Set.d) Neon aviation obstruction light - 1 No e) 2 Nos of special GI earth electrodes with copper plate 300 x300 x 3mm and copper flat (1”x1/4”) interconnection as per ISS complete with earth connection - 1 set.f) Hot dip galvanized lightning arrestor - 1 No. g) Flood light luminaries of specially Heavy type water poof Dust proof integral luminaries fitting provided with 150 Watts LED Light fitting Crompton / Philips make or Equivalent with 150W LED Bulb with drives, Alglas coated reflectors, with cable connection etc. complete as per standard specification. - 8 nos

Supply and laying of 3.5 x 35 sq.mm PVC LTUG aluminium armoured cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good

Supply and fixing of fancy glass shade and 7W / 9W LED bulb

Supply and fixing of WT bulk head fitting with guard suitable for with 7W/9W LED bulb.

Supply and Fixing of Stretcher-cum-Passenger Lift MRL, Speed 1 m/s with Stainless Steel Panels, Disable friendly, micro?processor based controller, VVVF drive, Fire rated doors and ARD-15 Persons

Drilling of Borewells anywhere in TamilNadu including transportation from one place to another with in TamilNadu in alluvial soil sedimentary strata of clay and sand stone shale pennles boulders etc. By first taking a pilot bore of 140mm/150mm dia and then enlarging to required dia direct or reverse rotary mud circulation method using rotary rigs fuel, labour and drilling bentonite and water required for drilling at site.- Up to 60m depth ending below ground level.

Up to 60m depth ending below ground level.

From 60m upto 90m Depth ending from ground level

From 90m upto 120 m Depth ending from ground level

From 120 to 150 Depth ending from ground level

From 150 to 180 Depth ending from ground level

From 180 to 210 Depth ending from ground level

Reaming 150mm dia pilot bore to 300mm dia bore as directed by the TWAD Board.

Up to 60m depth ending below ground level.

From 60m upto 90m Depth ending from ground level

From 90m upto 120 m Depth ending from ground level

From 120 to 150 Depth ending from ground level

From 150 to 180 Depth ending from ground level

From 180 to 210 Depth ending from ground level

Labour Charges for developing the Borewell with air compressor of 600 CFM capacity (Minimum 8 Hours) including transportation, labour and fuel charges for compressor as directed by TWAD Officers and conducting yield test by 'V' notch method.

Labour Charges for inserting PVC Casing pipes assembly (with slots or without slots) in the drilled hole including jointing the pipes with PVC Couplers with Cement paste etc., complete, supply and packing the annular space with pebbles of size and quality as approved by the Executive Engineer.

Supply and fixing of 160mm dia PVC special Blue pipes for Borewells

Plain pipes

Slotted special blue pipes

supplying and Delivery of Clear water vertical wet type of 5 HP Submersible Pump set suitable for 150 mm dia borewell con forming to IS 8034/2002 as amended there after and BEE 3 star rated capable of discharging noted LPM against head of water column due to all causes. The pump shall be with s.s shaft and dynamically balanced bronze or cast S.S impeller brass screws and CI FG 200 Grade pump Bowl /Diffuser with ISI markThe pump shall be directly coupled to a continuous rates two pole suitable wet type vertical squirrel cage induction motor as per IS 9283/1995 as amended there after suitable for operation in AC three phase 415 V +/- 10% 50HZ +/- 5%

Supply and run of 4 sq.mm 3 core flat type copper cable

FILTRATION EQUIPMENT :Supply, Installation, testing and commissioning of TOTALLY ANTI- CORROSIVE Bobbin Wound filter, 2000mm diameter. Fitted with pressure gauge panel manual air bleeder, water drain and emptying plug. fitted with collector arms and diffuser made from unplasticized PVC and polypropelene with all accessories required. Filtration velocity 40m³/hr/m². Max. working pressure : 2.5 kg/cm². Flow rate: 125m³/hr , outlet size 140mm, Height : 2040mm. Make : Certikin / Astral / Jandy

Supply, Installation, testing and commissioning of Valve Battery Manifold made in PVC with flanges for connecting to filters as per DIN 2501 standards. Consists of set of 5 - buttterfly valves for carrying out filtration, back-washing, rinsing and shut down of the filters. Size : 140mm Make :

Supply, Installation, testing and commissioning of Valve battery supports made in Zinc Plated Steel. Height : 2.30m. Make : Certikin / Astral / Jandy

Supply, Installation, testing and commissioning of Support Brackets : 2 Support Brackets with anti-vortex clamps and fixing screws For Ø 140 mm pipe. Make : Certikin / Astral / Jandy

FILTRATION MEDIA, Make : Certikin / Astral / Jandy

Grade 1. Size 0.5 mm - 1.0 mm. Price per bag of 25 kgs

Grade 3. Size 0.3 mm - 7.0 mm. Price per bag of 25 kgs

FILTRATION PUMP: Supply, Installation, testing and commissioning of Filter pump of Cast Iron Pumps 3000 r.p.m. Mechanical Seal in Stainless Steel. I.P.-54 motor protection. Stainless steel shaft. stainless steel strainer basket. Conn. PN- 16 according to DIN2501. Flowrate : 125m3/h @ 12m.head. 10 HP Voltage 400V/ 3 ph. Pump housing and Impeller in cast Iron. (5 working and 1 standby) Make : Certikin / Astral / Jandy

DISINFECTION SYSTEM Supply, Installation, testing and commissioning of Manual Dosing Equipment for Ph & Chlorine : Supply, Installation, Testing and commissioning of Membrane Dosing Pumps "EXACTUS" model. Electronic dosing pump to be mounted both on its base as well as hung on the wall. Pumps following CE regulations. IP- 65 protection. Power connections : 220/240V, 50/60 Hz. The materials in contact with liquid are : Ploypropylene, Viton, Teflon and PVC. Includes anti-acid plastic case. Operating panel protection provided by a transparent polycarbonate cover. Lubrication not required. Flow 20l/hr @ 5 bar (pH- 4, Cl-2). Make : Certikin / Astral /

Supply and Installation of Semi transparent polyethelene tank with external scale so that levels can be checked easily, capacity of tank 500lts. Make : Certikin / Astral / Jandy

Supply and fixing of Agitators for easy installation in the tanks, provided with steering grip in bakelite, rod and propellor arms in PVC, length of stirring rod 900mm. Make : Certikin / Astral /

POOL BASIN FITTINGS : Supply, Installation, Testing and commissioning of Drain grille in SS304. 500mm x 500mm Flow: 136m3/hr. Make : Certikin /

Supply, Installation, Testing and commissioning of Floor Inlets 50mm Made of ABS plastic and screws in stainless steel. Maximum recommended flow rate compliant with standard EN 13451-1: 12 m3/h. Make : Certikin / Astral / Jandy

Supply, Installation, Testing and commissioning of Suction inlet in ABS with cap internal thread of 11/2" dia and external thread 2" Make : Certikin / Astral / Jandy

Supply, Installation, Testing and commissioning of Drain Grill 200mm Ring support and grille in white ABS. Supplied with grille fixing screws. Flow rate 13 m3/hr. Make : Certikin /

Supply & Installation of ABS wall conduits 300mm long. Make : Certikin / Astral / Jandy

Supply & fixing of Overflow 1000 model. Ladder width 500 mm Ø 43 mm handrail, non-slip surface stainless treads, bright satin finish, anchoring fixtures for connection to the equipotential circuit and removable anchoring with plate for fastening to wall. AISI-316 handrail and steps. 4 “Luxe” steps + 1 double safety step. Make : Certikin / Astral / Jandy

Commissioning of the pool and maintaining the pool for 1 Month including necessary chemicals and manpower.

GRATINGS :Supply and fixing of Modular grating 300 x24 mm. Three Pin connection Make : Certikin / Astral / Jandy

Supply and fixing of Support profile Made in plastic. Suitable for 35mm high grating Supplied in 2 m length. Make : Certikin / Astral / Jandy

Supply and fixing of 90° corner tiles for overflow channels made of white, injection moulded copolymer polypropylene. Height 22 mm, channel width 295 mm Make : Certikin / Astral

MAINTENANCE ACCESSORIES : Supply of Pump caddy for stand-alone pool cleaners. Made of anodized aluminium tube and a 460 mm x 370 mm plastic platform. Face plate in AISI-304 stainless steel. Starter and cable. Make : Certikin / Astral / Jandy

Supply, Installation, Testing and commissioning of 600mm dia Sand filter with sand media. Make : Certikin / Astral / Jandy

Supply, Installation, Testing and commissioning of Victoria Monoblock Pump - 1 HP / Single phase. Supply of Pump. body and support in heat resistant plastic. Shaft with Noryl Impeller. Large capacity strainer. Make : Certikin / Astral / Jandy

Supply of aluminium pool cleaner - 800mm length. 2" connection. Trailing cable 110m Make : Certikin / Astral /

Supply of Extensible handles for cleaning attachments in anodized aluminium which can be adapted to the entire range of cleaning equipment, brushes, leaf skimmers and scoops.10.0mts. Long with Handle adaptor Make : Certikin /

Supply of Floating suction hose Made of blue polyethylene. Ø 50 mm (2”) 30 m Make : Certikin / Astral / Jandy

Supply of Shark leaf skimmers - wing-nut or wishbone fixing. Shark deep water leaf skimmer Make : Certikin / Astral / Jandy

Supply of Shark leaf skimmers - wing-nut or wishbone fixing. Shark surface leaf skimmer Make : Certikin / Astral / Jandy

Supply of Shark brushes - wing-nut or wishbone fixing. Shark special bottom curved brush Make : Certikin / Astral / Jandy

Supply of Shark brushes - wing-nut or wishbone fixing. Shark bottom/walls curved brush Make : Certikin / Astral / Jandy

Supply of Classic brushes - wing-nut fastening. S.S. bristle 165 mm Make : Certikin / Astral / Jandy

Supply of Free chlorine and pH Pooltester. Chlorine range: 0.5–6.0 mg/l & ph range: 6.8–8.2 Make : Certikin / Astral /

UNDER WATER LIGHTS :Supply and fixing of Underwater LED Warm White LumiPlus Flexi spotlightLight 32 W/12V AC. 4320lm with White Faceplate Make : Certikin / Astral / Jandy

Supply and fixing of Standard Niche Make : Certikin / Astral /

Supply and fixing of Junction Boxes, made in ABS, composed of 3 entries. 3/4" or PG-16 coupling. Make : Certikin / Astral /

Supply and fixing of Cable Conduit Hose, Flexible 1 mt. long conduit for conn. light to junction box. 3/4" and PG-16 threaded ends.. Make : Certikin / Astral / Jandy

Supply and installation of Transformer 300 W/12V with protection box. Make : Certikin / Astral / Jandy

CONTROL PANEL WITH NECESSARY CONROLS: Supply, Installation, Testing and commissioning of Control Panel c/w sheet steel enclosure, ELCBs, MCBs, O/L relays for pumps auto / pre- set (on timer) and hand controls for pumps (components are of ABB, L&T, Schneider).

ELECTRICAL CABLE WITH CONDUITS : Supply and installation of copper flexible electrical cables with necessary PVC conduits for the Swimming pool pumps, underwater lights. Make : Finolex / Polycab

1.5 Sqmm x 2 Core

2.5 Sqmm x 2 Core

2.5 Sqmm x 3 Core

4 Sqmm x 4 Core

Supply and Laying of PVC pipes and Pipe fittings with necessary flow markings(10Kg/cm2 pressure).Make: Supreme/Finolex (Pump Room is considered 7mtr from Pool

Upvc 40 Sch-50mm Dia (2")

Upvc 40 Sch-80mm Dia (3")

Upvc 40 Sch 100mm Dia (4")

Upvc 40 Sch 150mm Dia (6")

10Kg/cm2 PVC pipe 63mm Dia

10Kg/cm2 PVC pipe 75mm Dia

10Kg/cm2 PVC pipe 90mm Dia

10Kg/cm2 PVC pipe 110mm Dia

10Kg/cm2 PVC pipe 160mm Dia

6Kg/cm2 PVC pipe 160mm Dia

6Kg/cm2 PVC pipe 200mm Dia

6Kg/cm2 PVC pipe 250mm Dia

6Kg/cm2 PVC pipe 300mm Dia

Header Line

10Kg/cm2 PVC pipe 140mm Dia

10Kg/cm2 PVC pipe 160mm Dia

10Kg/cm2 PVC pipe 200mm Dia

10Kg/cm2 PVC pipe 250mm Dia

10Kg/cm2 PVC pipe 300mm Dia

Supply and fixing of PVC control & regulatory Valves (10kg/cm2 pressure). Make: Cepex/George Fisher/FIP

Ball Valve 50mm Dia

Make :Cepex/GF/FIP 75mm Dia

Butterfly Valve 110mm Dia

Make :Cepex/GF/FIP 160mm Dia

Non Return valve 140mm Dia

Make :Cepex/GF/FIP 160mm Dia

Foot Valve 160mm Dia

Bolts and Nuts for 110 mm, 140 mm, 160mm B/V &

RPP INFRA PROJECTS LIMITED (BID ID -1185059)