Annual Plan Niramaruthur GP Project No 14 Pathambad Subcenter Renovation Ward 8

Amount

Renovation

2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

50.6.7.1:Laterate masonry with neatly dressed laterate stone of size 40x20x15cm or nearest size in cement mortar 1:6 for foundation and basement including all cost of materials, labour charges etc.

OD89468/2025-2026:Engaging coolie for dismantling old and damaged inter lock

50.2.26.1:Filling with contractor own earth (excluding rock) in open areas in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge.

OD89469/2025-2026:Providing and laying 60 mm thick departmental cement concrete interlocking paver block making mechine with strong vibratory compaction, of approved size, design & amp ; shape , laid in required colour and pattern over and including 50 mm thick compacted bed of 6mm course aggregate, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-chrge .

OD87137/2025-2026:[ OD from 16.68 ] Providing and laying 60 mm thick factory made cement concrete interlocking paver block making mechine with strong vibratory compaction, of approved size, design & amp ; shape , laid in required colour and pattern over and including 50 mm thick compacted bed of 6mm course aggregate, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-chrge .

15.56:Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

50.6.2.3:Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for super structure above floor two level upto floor five level with thickness 15cm in : CM 1:6 ( 1 cement : 6 coarse sand) etc complete

13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.2.2:15 mm cement plaster on the rough side of single or half brick wall of mix:1:6 ( 1 cement : 6 fine sand)

13.47.1:Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

8.2.2.1:Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shadeArea of slab upto 0.50 sqm

OD89957/2025-2026:Dismantling , cutting and removing , cutting of truss work and old sheet work manually/mechanical means including stacking of ervicable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer -in-charge .

OD93475/2025-2026:Steel work for purlin/single section with Departmental GI pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer , including welding and bolted with special shaped washers etc complete

10.2:Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

OD93608/2025-2026:Providing and fixing precoated galvanised iron profile sheets(size,shape and pitch of corrugation as approved by Engineer i charge) 0.35mm(+0.05%) total coated thickness with zinc coating 120 grams per sqm as per IS: 277,in 240 mpa steel grade,5-7 microne epoxy primer on both side of the sheet and polyester top coat 15-18 microns.Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length up to 12 meter or as desired by Engineer- in- charge.The sheet shall be fixed using self drilling/self tapping screws of size(5.5x55mm)with EDPM seal, complete up to any pitch in horizontal/vertical or curved surface,excluding the cost of purlins,rafter and trusses and including cutting to size and shape wherever required.

OD93694/2025-2026: Fixing precoated galvanised iron profile sheets departmental (size,shape and pitch of corrugation as approved by Engineer- in- charge )0.35 mm (+0.05%),total coated thickness with zinc coating 120 grams per aqm as per IS: 277,in 240 mpa steel grade,5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns.Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length up to 12 meter or as desired by Engineer-in-charge.The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal,complete up to any pitch in horizontal/vertical or curved surfaces,excluding the cost of purlins,rafters and trusses and including cutting to size and shape wherever required. Details of cost for 216.14 sqm ( External diamension of plinth) Area of roof 20.2x10.70m=216.14sqm Sheets Used =20Nos x 10.70m x 1.06m= 226.84sqm add 3% wastage = 6.81 total = 233.65sqm

13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

OD89549/2025-2026:Providing and fixing 150mm wide,square cut PVC 4kg/cm2 rain water gutter pipe with iron brackets with 25x5 mm size flat , screws and washers etc, including making necessary connections with rain water pipes etc complete.

4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III)derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

4.3.1:Centering and shuttering including strutting, propping etc. and removal of form work for:Foundations, footings, bases for columns

10.25.2:Item Shifted to Sub head 14 as item 14.73 Item Shifted to head 14 as item 14.74 Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

13.112.1:Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shadeOld work (Two or more coats applied @ 1.43 ltr/ 10 sqm) over existing cement paint surface

21.5:Providing and fixing powder coated aluminium work ( minimum thickness of powder coating 50 micron) consisting of tee /angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in-Charge ( level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately ).

50.12.4.2:Providing and fixing false ceiling with 7.5 mm thick PVC wooden grains panel board ceiling of approved quality in aluminium frame work with necessary screws etc complete ( aluminium frame work shall be paid separately)

OD96350/2025-2026:Lettering in stainless steel for Name board work including labour, material and fitting chargesetc complete. (Area to be measured including standard size between letters)

OD96435/2025-2026:Providing and fixing Granite of any colour and shade for Name board ,of required size laid over base of cement moortar 1:4(1 cement :4 coarse sand)including all charges etc.complete at all levels ,including lettering &fixing

OD188694/2025-2026:Modi Data of 25.7 Fabricating and fixing in position aluminium coposite pannel of 4mm or nearest thick using steel screw ,nut, bolt ,washers ,cleats weather sealnt ,fastners ,to aluminium frame as per direction of departmental officers including cost and conveyance of all material and labour chargesetc , complete

SIBIN KULANGARA (BID ID -2294669)

RIJIN A (BID ID -2294705)

Bidder Name

RIJIN A

SIBIN KULANGARA

RAMEEZ M FAROOK