SERVICE & MAINTENANCE WORK OF EXISTING PUMP AND MOTOR SYSTEM FOR THE YEAR OF 2026-27

DAP_Motor Rewinding upto 3 HP

DAP_Motor Rewinding upto 5 HP

DAP_Motor Rewinding upto 7.5 HP

DAP_Motor Rewinding upto 10 HP

DAP_Motor Rewinding upto 12.5 HP

DAP_Motor Rewinding upto 15 HP

DAP_Motor Rewinding upto 17.5 HP

DAP_Motor Rewinding upto 20 HP

DAP_Intermediate Piece (I.P.) with I.P. Leaded Bronze Bush

DAP_Oil Seal (Pump Oil Seal)

DAP_Oil Seal Steel Bush (Oil Seal Sleeve)

DAP_Impeller Shell moulded with aluminium & bronze

DAP_Discharge Outlet (D.O.) Bearing(LB bush) and D.O Steel bush (SS sleeve)

DAP_D.O. Bearing( I.D.O LB bush)

DAP_Steel Bush (I.D.O. SS sleeve)

DAP_Allen Screw

DAP_Pump Shaft (Stainless Steel) Counter less ground with key way upto 8 stages

DAP_Pump Key (Stainless Steel) Upto 8 stages

DAP_Pump coupling (Stainless)

DAP_Non-Return Valve assembly complete with rubber O rings

DAP_Cable Guard

DAP_Brass Filter

DAP_Labour Charges (Overhauling of pump only)

DAP_Upper Flange

DAP_Lower Flange

DAP_Upper Housing

DAP_Lower Housing

DAP_Lock Ring (Circlip Big)

DAP_Starter 3 HP

DAP_Starter 4 HP

DAP_Starter 5 HP

DAP_Starter 7.5HP

DAP_Starter 10HP

DAP_Starter 12.5 HP

DAP_Starter 15 HP

DAP_Starter 17.5HP

DAP_Starter 20 HP

DAP_Carbon housing (TB Plate)

DAP_Thrust Bearing block assembly (TB Bottom)

DAP_Tip Carbon/Ferrode Padding

DAP_Studs and Nuts

DAP_Bearing (Gun Metal Bush) centrifugal cost aluminium bronze bearing bush

DAP_Circlips(small)

DAP_Motor Base with Pin

DAP_Transportation of Pumping machinaries

DAP_Re-errection charges of Pumping machinery including overhauling and painting

DAP_Lifting of submersible pumpsets

DAP_Labour Charges Overhauling

DAP_Labour charges for Lifting of non functioning submersible pump set along with cable and GI pipes

DAP_Labour charges for lowering additional GI pipes of dia 32 / 50mm dia including transportation charges (New GI pipe required will be supplied by the department free of cost & released GI pipes should be handed over to the department (Labour charges only) Upto 3 lengths

DAP_Labour charges for lowering additional GI pipes of dia 32/50mm dia including transportation charges (New GI pipe required will be supplied by the department free of cost & released GI pipes should be handed over to the department (Labour chargesonly) above 3 lengths

DAP_Lifting of struck up submersible pump set upto 300 ft (BWSSB SR 2017-18/O150G/Sl No.26)

DAP_Lifting of struck up submersible pump set above 300 ft (BWSSB SR 2017-18/O150G/Sl No.27)

DAP_Labour charges for Laying U.G. Cable upto 3.5 core 25 Sq.mm as per PWD Electrical SR 2010-11, P-68,1-1, Class A PVC cable

DAP_Refilling available earth around pipe lines, cable in layers not exceeding 20cms in depth, compacting each deposited layer by ramming after watering with lead upto 50m and lift upto 1.5m including cost of all labour complete as per specification PRE SR 2011-12, P-3,1-6.

DAP_Fabricating, Supplying and mounting MS Box made out 14 SWG suitable for Foor/Wall mounting, fully weather proof with provision for better heat dissipation, provided with hinged front over equipped with temper proof locking arrangements with suitable size clamps with necessary cable entry pipe with gland and box should be finished with 2 coats of red oxide primer paint and finally finished with approved colour enamelled metal paint etc., complete

DAP_Supplying and fixing angle iron frame work fabricated out of M.S. angle iron and M.S. flat with bolt, washer etc and painted with 2 coats of red oxide and then two coats of approved paint 75x75x6mm (PWD ELE SR 2014-15, Pg.No.49, lt.No.6.39.3)

DAP_Erection of panel Board & MS Box (Outdoor type) (Gulbarga PRED, Pg.No.57, lt.No.12.2)

DAP_Supplying and fixing polished wood board made out of not less than 15mm thick planks at both sides with planks made out of not more than 2 pieces and fixing the same to the wall using tapered wooden plugs screws etc

DAP_Supply and fixing of hylam brand hand plastic sheet 3mm thick with necessary nitches for fixing switches, regulators etc and fixing of exciting wood or metal box using NF Screw

DAP_Supply and fixing of 16 Amps Contactor

DAP_Supply and fixing of 25 Amps Contactor

DAP_Supply and fixing of 33 Amps Relay

DAP_Supply and fixing of 23 Amps Relay

DAP_Supply and fixing of 15 Amps Relay

DAP_Supply and fixing of Single Phase Preventer_7.5 to 15 HP

DAP_Supply and fixing of Single Phase Preventer_20 to 30 HP

DAP_Supply and fixing of RYB Rotary Switch_volt selector

DAP_Supply and fixing of Terminal Plate_connector 30A

DAP_Supply and fixing of Terminal Plate_connector 60A

DAP_Supply and fixing of No-Volt_NV_Coil

DAP_Supply and fixing of wiring kit_DOL upto 7.5HP

DAP_Supply and fixing of wiring kit_SD upto 25HP

DAP_Supply and fixing of LED Indicator

DAP_Supply and fixing of Ammeter

DAP_Supply and fixing of Voltmeter

DAP_supply and fixing of Blade set 16A

DAP_supply and fixing of Blade set 25A

DAP_Supply and fixing of CT Coil 50 bar 5 and 75 bar 5

DAP_Labour Charges_for over hauling

DAP_Gl Pipe Threading including transportation

DAP_Cable Joint