PROVISION OF BAGGAGE STORE, YOGA CENTRE AND FAMILY WELFARE CENTRE AT NAVAL PARK, UNDER GE (NB) VISAKHAPATNAM

Amount

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in Soft/ Loose soil complete all as specified and as directed.

Excavation in any type of soil by mechanical means (Hydraulic excavator) over areas exceeding 1.5 m in width or 10 sqm on plan, including dressing of sides and ramming of bottoms, lift upto 1.5 m including getting out the excavated soil all as specified and as directed.

Excavation in any type of soil by mechanical means (Hydraulic excavator) over areas exceeding 1.5 m in width or 10 sqm on plan, including dressing of sides and ramming of bottoms, lift exceeding 1.5 m but not exceeding 3.00 m including getting out the excavated soil all as specified and as directed.

Excavation in any type of soil by mechanical means (Hydraulic excavator) in foundation trenches or drains not exceeding 1.5 m in width or 10 sqm on plan, including dressing of sides and ramming of bottoms, lift upto 1.5 m including getting out the excavated soil all as specified and as directed.

Excavation in post holes each not exceeding 0.5 Cu.m, getting out in Soft / Loose soil, including returning, filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm thick, watering and removing surplus soil to a distance not exceeding 50m and making good surface complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil complete all as specified and as directed. Note: A deduction of 10% shall be made from total computed volume of filling to cater in bulk irrespective of machinery used for ramming.

Removal of excavated material [Soil] to a distance exceeding 1.5 Km but not exceeding 5 KM and depositing where directed complete all as specified and as directed.

M & L for Moorum / Red Bajri filling under Floors or in Pavings laid in layers not exceeding 30 cm thick, spread levelled and rammed / rolled including watering to required level and gradient complete all as specified and as directed. Note: Measurements shall be taken after consolidation of earth and 10% deduction shall be made for payments.

M & L for Hardcore of gauge not exceeding 63mm of broken stones or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick watered and rammed to true surface complete all as specified.

M & L for sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

M & L for providing Anti - termite treatment to top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and as directed.

M & L for Providing Pre Construction Antitermite treatment to the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and as directed.

M & L for Providing Pre Construction Antitermite treatment to the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and as directed.

M & L for Providing Pre Construction Antitermite treatment to the the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and as directed.

M & L for PCC 1:2:4, Type B-2, using 40mm graded stone aggregate as in Foundation, Fillings, Mass concrete, Footings etc complete all as specified and as directed.

M & L for PCC 1:3:6, Type C-2, using 40mm graded stone aggregate as in Foundation, Fillings, Mass concrete, Footings etc complete all as specified and as directed.

M & L for PCC 1:4:8, Type D-2, using 40mm graded stone aggregate as in Foundation, Fillings, Mass concrete, Footings etc complete all as specified and as directed.

M & L for RCC M-30 design mix, using 20mm graded stone aggregate as in foundations including rafts, footings, foundation beams, plinth beams, bases for columns etc complete all as specified and as directed.

M & L for RCC M-30 Design Mix, using 20mm graded stone aggregate as in Columns, pillars, piers, posts and struts etc. complete all as specified.

M & L for RCC M-30 Design Mix, using 20mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels etc. complete all as specified.

M & L for RCC M-30 Design Mix, using 20mm graded stone aggregate as in Slabs supported on walls, beams, columns in floors, roofs, landings, balconies, canopies, deck slabs complete all as specified and as directed.

M&L RCC M-30 design mix using 20mm graded stone aggregate as in staircases including landings complete all as specified and as directed.

M & L for Plain / Reinforced cement concrete 1:2:4, Type B1, using 20mm graded stone aggregate in lintels,bands etc up to 1.5m span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates including weathering, slightly rounded or chamfered angles and throating as directed including use and waste of form work, complete all as specified and as directed.

M & L for PCC 1:3:6, Type C-1, using 20 mm graded stone aggregate as in Coping and the like including weathering, slightly rounded or chamfered angles and throating including formwork [straight or curved] complete all as specified and directed.

M & L for providing Precast RCC 1:2:4, Type B-1 using 20mm graded stone aggregate as in landings, cover slabs [for manholes etc], chullah hoods, chajjas, water troughs, mangers, Shelves and similar articles with plain faces set in cement mortar 1:4 complete all as specified and as directed.

M & L for PCC 1:2:4, Type B-0, using 12.5mm graded aggregate as in benching to manholes including use of forms and moulds and finishing even and smooth with using extra cement and complete all as specified and as directed.

M & L for providing factory made kerb stone of M-25 grade cement concrete laid at or near ground level to the required line, level and curvature, jointed with cement mortar 1:3, including making joints with or without grooves, with thickness of joints except at sharp curve shall not be more than 5 mm, including making drainage opening wherever required including necessary earthwork excavation and applying Two Coats of synthetic enamel paint of approved colour and pattern complete all as specified and as directed.

M & L for providing Precast Cement Concrete block masonry with solid blocks in PCC 1:3:6, Type C-1 using 20mm graded stone aggregate exceeding 10cm width setting in mortar 1:6 complete all as specified and directed.

M & L for brick work with Fly Ash bricks, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 complete all as specified and as directed.

M & L for brick work in half brick thick walls using Fly Ash bricks straight or curved on plan to any radius built in Cement Mortar 1:4 including 2 Nos of 8mm dia bars at every fourth course of brick work complete all as specified and as directed.

Use and removal of steel formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits [if any] of foundation and plinth beams and similar work, vertical or to batter for rough finished surfaces complete all as specified and as directed.

Use and removal of steel formwork to sides of pillars, posts, struts, piers, columns and stanchions of any shape / cross section for rough finished surfaces of concrete complete all as specified and as directed.

Use and removal of steel formwork to sides and soffits of floor or roof beams, beam launchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc, splays between floors and beams and similar works for rough finished surfaces of concrete complete all as specified and as directed.

Use and removal of steel formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick [horizontal or sloping] including rough finished surfaces complete all as specified and directed.

Use and removal of steel formwork to staircases with sloping or stepped soffits including risers and stringers and fins, louvers, fascia, sides and soffits of arch curved for fair finished surfaces of concrete complete all as specified and as directed.

S & F factory made single rebated Wood Polymer Composite [WPC] solid door/ window Frames/ Chowkhats of size 65mm x 75mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms), fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N(Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with properties of termite / borer proof, water/ moisture proof and fire retardant, fixed in position complete all as specied and as directed. Note: The hold fasts/ lugs/ fasteners shall be measured and paid separately under relevant items of this Schedule/ BoQ.

S & F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. Note: Stainless steel butt hinges and necessary S S screws shall be paid separately

S & F 40 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

S & F 0.9 mm thick Decorative Laminate, Type - 1 of Surface Finish, Colour and Pattern as approved, fixed with approved adhesive as per manufacturer's instructions, complete all as specified and directed.

Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality complete all as specified and as per Manufacturer instructions. Note:(a) For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. (b)The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose. (c) Glass Panes shall be measured and paid separately at supply only rates.

M & L for Powder coated aluminium sections of approved colour for doors, Windows, Ventilators, Partitions, with frames and shutters fully or partly glazed, sliding / openable, with extruded aluminium sections not less than 1.5mm thick and powder coating not less than 60 micron thick including necessary jointing cleats, rubber beading, neoprene packing, aluminium snap beading, screws, powder coated aluminium fittings such as handles, aluminium butt hinges , aluminium tower bolts, stainless steel friction hinges, locking arrangements etc. complete all as specified and as directed. Notes: [a] The size of aluminium extruded sections shall conform to Designation 63400 all shall be as specified in relevant IS code and as specified in MES Schedule Part - I. [b] Panel inserts such as Glass / Particle board / Gauze and grill shall be measured and paid separately at supply only rates. [c] Weight of aluminium sections shall only be accounted for payment purpose. Weight of aluminium Handles, Butt Hinges & Tower Bolts shall not be accounted for payment purpose. [d] The unit rate quoted shall be deemed to include for cost of jointing cleats, glazing clips, rubber beading, neoprene packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as handles, aluminium butt hinges, aluminium tower bolts, stainless steel friction hinges, Peg stays, locking arrangements etc., and fixing only of panel inserts of glass / particle board / gauge etc and grills.

Supply only 5 mm thick Sheet Glass ordinary quality in squares exceeding 0.5 Sq.m in each pane complete all as specified and as directed.

Supply only 4mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and as directed.

Supply only 12mm thick, Prelaminated Particle Board, Decorative Choice Lamination on Both Sides, Medium Density, Exterior Grade complete all as specified and as directed.

Supply only Stainless steel wire mesh with aperture not exceeding 1.40 mm and dia of wire 0.36 mm complete all as specified and as directed.

S & F 12mm thick Toughened Glass Door Rimless swing type including locking arrangement etc. cut to size, holes drilled, fitted with necessary fixing arrangements, edges mounted with dry set neoprene/ EPDM gaskets of suitable size including Handles on both sides, 300mm long made with 25mm dia Stainless Steel pipe of Grade AISI 304 for each shutter complete all as specified and as directed.

Supply only 9.5mm thick frosted glass in squares exceeding 0.5 sqm in each pane complete all as specified and as directed.

Supply and stick 25 micron thick Solar control film, reflective type sticked to glass panes as per instructions of manufacturers complete all as specified and as directed.

S & F Double action floor spring hydraulically regulated, ISI Marked, made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and as directed.

S&F 25mm dia decorative type Brass handles, bright polished, 600mm long including all fittings complete all as specified ad directed.

S&F 100mm long Butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, type C-13 omplete all as specified ad directed.

S & F brass Mortice night latch, Vertical type of size 100 mm, 6 Levers with 2 keys of Godrej Make, complete all as specified and as directed.

S & F Brass barrel Tower Bolt of size 150 mm size with cast or sheet barrel and rolled or cast bolts complete all as specified and as directed.

S & F Brass barrel Tower Bolt of size 300 mm size with cast or sheet barrel and rolled or cast bolts complete all as specified and as directed.

S & F Brass Sliding Door Bolt with hasp and staple [Bolt Type] of size 300 mm and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

S & F Aluminium anodised Handle, of extruded section Fabricated Type of size 150mm long complete all as specified and as directed.

S & F decorated pattern rolling type venetian blinds with necessary frame work and required operating patterns/arrangements as approved, fixed on walls complete all as specified and as directed. Make : Vista, Deco, Hippo or equivalent approved

S & F Stainless Steel Railing made with Stainless Steel Pipes of wall thickness not less than 1.6mm, of Grade AISI 316L, standard quality, bright polish finish, using 50mm dia pipes for hand rail, 25mm dia pipes for vertical supports / balusters and 25mm dia pipes as in tie bars in three layers, SS tubes shall be welded at the turnings and junctions, welded portions shall be completely grinded and brought to bright and smooth finish including all bends, elbows, making holes in the floor / steps, grouting with epoxy to achieve full strength of railing complete all as specified and as directed.

S & F Mild Steel work conforming to Fe - 290, Grade E-165 as in Bands, Straps, Supports or Stays for Rainwater, Ventilating Pipes, including Bolts, if required, Hooks [Stay], heavy, for Large Gates, Hook and Pintle Hinges, large Hasps and Staples, Chains, hand made Sliding Bolts, Clamps, Hold Fasts, Wall Ties, Hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles complete all as specified and as directed.

S & F Mild Steel work as in Tubular Trusses, Posts etc including special shaped washer etc complete using ERW or induction butt welded tubes confirming to IS - 1161, Grade YST - 240, Medium Grade of any dia complete all as specified and as directed.

S & F Rolled Mild Steel work conforming to Fe 410-W, Grade-E- 250, Quality-A as in Plates [Plain & Chequered], Channels, Angles, square cut or notched [ordinary or counter sunk] forming holes without any attachment including fixed with Nut and Bolt / welding complete all as specified and as directed.

S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

S & F Reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D of 5mm to 10mm dia bars as in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending, spirally for hooping, hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

M & L for providing roof tiles, Mangalore pattern, interlocking at side joints, laid dry complete all as specified and as directed.

supply only Integral water proofing Liquid complete all as specified and directed.

M & L for Prepairing surfaces of new concrete roof by picking, sweeping clean and washing down with water to remove dust etc and brushing neat cement slurry with 3.0 KG of cement per Sq.m area, rendering 10mm thick in cement mortar 1:3 on concrete surfaces finished even and smooth without using extra cement including mixing of water proofing compound of approved make as per manufacturers instructions for levelling the surface smooth to receive the water proofing membrane, priming the surface with a coat of cold applied bituminous primer @ 0.50 KG per Sq.m, applying a coat of Blown Bitumen of grade 85/25 @ 1.2 Kg per Sq.m, laying Polymeric water proofing membrane of weight not less than 3.00 Kg per Sq.m reinforced with polyester non-woven fabric of weight not less than 150 Grams per Sq.m, by torch application with side over lap of 100mm & end over lap of 150mm & tucked into the chases on vertical surfaces by thermo fusion including applying a coat of Blown Bitumen of grade 85/25 @ 1.2 Kg per Sq.m on top for water proofing treatment complete i complete all as specified and as directed. Note: Water proofing compound will be measured and paid separately.

M & L for Plain Cement Concrete Tiles of size 250 X 250 mm / 300 X 300 mm, 22mm thick, Hydraulically pressed as in Floors, set jointed and pointed in neat cement slurry to match including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 of cement complete all as specified and as directed.

M & L for providing Ridge or Hip tiles to suit Mangalore pattern roofing tiles, bedded and jointed in cement mortar 1:6 complete all as specified and as directed.

M & L for providing ceiling tiles suitable for Mangalore pattern tile roofing , laid dry complete all as specified and as directed.

S & F Calcium Silicate False Ceiling at all heights in true horizontal level made out of Calcium Silicate boards of size 1800 X 1200 mm, having Integral densified reinforced edges of 15mm thickness all around with a collar of width 24mm and 10mm thickness at the centre of siliceous and calcareous material reinforced with cellulose fibre of approved texture, design and patterns, suspended on the Exposed Metal Frame Ceiling Grid of suitable size including suspended Exposed Inter-locking Metal Frame Work using GI Main "T" Runner of size 24x38mm, 0.33mm thick, spaced 1200mm centre to centre, Cross "T" of size 24X32mm, 0.33mm thick, 1200 mm long spaced between Main "T" at 600 mm centre to centre to form a grid of 1200X600 mm and secondary Cross "T" of 600mm long and of size 24X32mm, 0.33mm thick of the 1200x600mm panel to form grid of size 600x600mm, resting on periphery walls / partitions on GI Perimeter Wall Angle of size 24X24X3000 mm, 0.40 mm thick with the help of rawl plugs at 230mm centre to centre with 40mm long dry wall SS Screws including cutting/making opening for services like diffusers, grills, light fittings, smoke detectors etc., wherever required. Main "T" Runners shall be suspended from ceiling using galvanised mild steel [Galvanizing @ 80 Grams per Sq.m] 50 mm long, 8 mm outer diameter M-6 Dash Fasteners, 6 mm dia fully threaded hanger rod up to 1000 mm length and L-Shape level adjuster of size 85x25x25x2 mm, spaced at 1200mm centre to centre along Main "T". Bottom exposed width of 25 mm of all sections shall be pre-painted with polyester baked paint at all heights complete all as specified and as directed. Note: The size / sections of materials specified in the description of item is as per minimum requirement. If the same size or section is not available, next higher size shall be provided by the contractor without any extra cost to the Department.

S & F Aluminium Composite Panel sheet of 3 mm thick with skin thickness of 0.25mm of aluminium on both sides, sandwiched by 2.5mm polyethylene core with PVDF coating of 30 micron fixed over Stainless Steel Frame Work with suitable Self Tapping Screws in approved pattern / size complete all as specified and as directed.

S & F Acrylic sheet letters, back light illuminated type, size not less than 10 inch width and not less than 15 inch height and not less than 50mm thick and elevated from the surface, fixed on suitable size white/coloured metallic frame, letters provided in hindi and english languages, pattern/ design as approved by competent authority and frame work fixed on ganite/ tile/ ACP cladding complete all as specified and as directed. Note : Internal lighting in letters shall be measured & paid separately under relevant items of this BoQ.

S & F 3-4mm thick Acrylic fibre sheet, back light illuminated type, front side CNC Artistic elevation design cut to shape/ design/ pattern as approved by competent authority and back side plain sheet, including suitable metallic frame work, fixed on internal/external walls/ceiling upto 9 Metres height including use and removal of necessary double scaffolding complete all as specified and as directed. Note : Internal lighting in letters shall be measured & paid separately under relevant items of this BoQ.

M & L for 100 mm thick, PCC 1:4:8, Type D-2, using 40mm graded stone aggregate as in Sub base for flooring complete all as specified and as directed.

M & L for 25 mm average thick PCC 1:2:4, Type B-0, using 12.5mm graded aggregate as in levelling course over sub base, surface finished even and fair to receive topping layer complete all as specified and as directed.

M & L for 75mm thick PCC 1:3:6, Type C-1, using 20mm graded aggregate as in Plinth protection etc surface finished even and smooth with out using extra cement and providing 12mm thick joints for full depth of PCC at every 3.00 m and every change of direction duly filled with mastic filling comprising of 01 Part of heated bitumen blown grade of any penetration and 3 parts of sand [all by weight] complete all as specified and as directed.

M & L for Vitrified Tiles, Double charged, Dark Shade, Coloured, Premium Quality, of size exceeding 0.36 Sqm but not exceeding 0.42 Sq.m, 8 to 9 mm thick as in Floors, set and jointed in cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for Polished Glazed Vitrified Tiles, Coloured, Premium Quality, of size exceeding 0.42 Sq.m not exceeding 1.00 Sq.m, 09 to 10 mm thick as in Floors, set and jointed in cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: [a] The colour/ shade/ design of tiles shall be as approved by GE. [b] The tile joint shall be kept as 5mm using 5mm thick tile spacers and masking tape shall be provided before applying of the polymer based cementitious grout and the surplus grout materials shall be thoroughly cleaned immediately.

M & L for Polished Glazed Vitrified Tiles, Coloured, Premium Quality, of size exceeding 0.42 Sq.m not exceeding 1.00 Sq.m, 10 mm thick as in Skirting and Dado, set and jointed in cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. Note: [a] The colour/ shade/ design of tiles shall be as approved by GE. [b] The tile joint shall be kept as 5mm using 5mm thick tile spacers and masking tape shall be provided before applying of the polymer based cementitious grout and the surplus grout materials shall be thoroughly cleaned immediately.

M & L for Non Skid Ceramic Tiles, Joint Free, Coloured, Premium Quality of size exceeding 0.18 Sq.m and not exceeding 0.38 Sq.m, 7 to 8 mm thick [Square or Rectangular] as in Floors etc, set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for Non Skid Ceramic Tiles, Joint Free, Coloured, Premium Quality of size exceeding 0.11 Sq.m and not exceeding 0.18 Sq.m, 7 to 8 mm thick [Square or Rectangular] as in Floors etc, set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for Joint Free Glazed Ceramic Tiles, Edge Cut, Concept Type, Coloured, Premium Quality, of size 450 mm X 350 mm, 7 to 8 mm thick as in Vertical Surfaces such as Skirting, Dado etc set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. The colour / shade / design of tiles shall be as approved by GE.

M & L for Granite Stone Slabs of 18 to 20 mm thick of Colour Mexican Red / Ruby Red / Z Black / Pearl Black as in Floors, Steps, landings, Window Cills, Cooking Platforms and the like with machine cut edges, Table rubbed and prepolished to smooth mirror finish all to required sizes, granite stone slabs shall be of design / pattern as directed, including inlays, borders, margins in two or more colours / shades, designs / patterns of stone slabs, set and bedded with grey cement [slurry] and jointed and pointed flush using polymer based cementitious tiling joint filler to match the shade of the Granite Slabs including screed bed or bedding layer of mortar 20 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: Single stone slab shall be used for entire Width and Length of Steps, Window Cills, Cooking Platform etc. and joints shall match with the flooring. The projected edges of slabs shall be bull nosed / half rounded. The edges of the treads and landings shall also be provided with three Nos of grooves.

M & L for Granite Stone Slabs of 18 to 20 mm thick of Colour Mexican Red / Ruby Red / Z Black / Pearl Black as in Skirting, Dado, Risers of Steps, Jambs, Pillars, Wall Lining [Veneering to Wall] etc. with machine cut edges, Table rubbed and prepolished to smooth mirror finish all to required sizes, granite stone slabs shall be of design / pattern as directed, including diagonals, inlays, borders, margins in two or more colours / shades, designs / patterns of stone slabs, set and bedded with grey cement [slurry] and jointed and pointed flush using polymer based cementitious tiling joint filler to match the shade of the Granite Slabs over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. Note: Single stone slab shall be used for entire height of Skirting / Dado / Risers and joints shall match with the flooring.

M & L for Inter Locking Paving Blocks of 80mm thick, made with M-40 Grade cement concrete using 20 mm graded stone aggregate, Hydraulically pressed of approved colour and pattern, shape and size conforming to IS - 15658 set in floors complete all as specified and directed.

M & L for rendering 5 mm thick in Cement Mortar 1:3 on concrete Ceiling surface finished even and smooth without using extra cement complete all as specified and as directed.

M & L for rendering to brick / concrete surfaces, 10 mm thick in Cement Mortar 1:6, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L for rendering 5mm thick in cement mortar 1:4 including mixing water proofing compound as per manufacturers instructions over a backing coat of 10mm thick in CM 1:6 on concrete or brick masonry surfaces and finishing the top surface even and smooth without using extra cement complete all as specified and as directed. Note: Water proofing compound will be measured and paid separately.

M & L for rendering to brick / concrete surfaces, 15 mm thick in Cement Mortar 1:4, including mixing water proofing compound as per manufacturers instructions and finishing the top surface even and smooth without using extra cement complete all as specified and as directed. Note: Water proofing compound will be measured and paid separately.

M & L for preparing of newly plastered wall surfaces of any description over 10cm girth or width and painting with two coats of interior stucco marble special effect paint of approved texture/ pattern/ colour with egg shell/ glossy finish, over a coat of primer over one or more coat cement based wall care putty as per manufacturer's instructions complete all as specified and directed.

M & L for preparing newly plastered RCC Ceiling surfaces by using vaccume based sanding machine and applying two coats of Acrylic washable Distemper by using auto roller/airless sprayer, over a coat of alkali resistant primer on ceiling over 1mm thick Cement based Wall Care Putty by using multipurpose mixture for proper mixing of putty and putty sprayer for application of putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces complete all as specified and as directed. Note:- The contractor shall carryout Distempering & allied works under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Distempering & allied works through their authorised applicators before commencement of the work to GE for approval.

M & L for Two coats of Weather Proof Exterior Emulsion Paint [100% Acrylic] by using auto roller/ airless sprayer over a Coat of Exterior Primer over 1mm thick Cement based Wall Care Putty [primer and putty shall be of same manufacturer as that of exterior emulsion paint] by using multipurpose mixture for proper mixing of putty and putty sprayer for application of putty on newly plastered walls/ ceiling, pillasters, bands, borders, soffits of chajjas and projections including rubbing with sand paper to obtain a smooth surface complete all as specified and as directed. Note:- The contractor shall carryout Exterior Emulsion Painting and allied works under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Exterior Emulsion Painting through their authorised applicators before commencement of the work to GE for approval.

S & F CP Grating Dome type, 100 mm dia [Minimum weight 60 Grams] without waste hole or with waste hole to insert waste pipe complete all as specified and directed.

S & F 5.5mm thick Sheet Glass Shelf assembly with Bracket, railing 60 cm long complete all as specified and as directed.

S & F Corner Glass Shelf with Bracket and railing complete as per Jaquar Catalogue No. ACN-1173 or its equivalent in Kohler / Grohe complete all as specified and as directed.

M & L for two coats with Plastic emulsion painting over a coat of alkali resistant primer over two or more coats of Cement based Wall Care Putty on newly plastered wall surface including rubbing with sand paper to obtain a smooth surface complete all as specified and as directed.

M & L for two coats of synthetic enamel paint over one coat of pink primer to newly untreated wooden surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

M & L for two coats of Synthetic Enamel paint over one coat of Red Oxide / Zinc Chrome Primer on new steel surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

S & F 75mm bore PVC [SWR] Multi Floor Trap with grating including jointing with solvent cement complete all as specified and as directed.

S & F PVC [SWR] gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and as directed.

S & F 75mm bore PVC floor Trap with grating including jointing to waste pipe, fixed in cement concrete type B1, 1:2:4 complete all as specified and as directed.

M & L for concrete bed to drain pipes of size 150 mm bore packing under and haunching against the sides of pipes after they are laid and fitted in cement concrete, Type C2, 1:3:6, using 40mm graded stone aggregate complete all as specified and as directed.

M & L for 150 mm dia RCC Pipes, Class NP3, laid in trenches and jointed with collars in cement mortar complete all as specified and as directed.

S & F 200mm bore UPVC [SWR] pipes single socketed, in any length with rubber ring joints, fix to walls complete all as specified and as directed.

S & F 110mm bore UPVC [SWR] pipes single socketed, in any length with rubber ring joints, fixed to walls including necessary brackets, clamps as in rain water down pipes complete all as specified and as directed.

S & F 75mm bore UPVC [SWR] pipes single socketed, in any length with rubber ring/ solvent cement joints, laid in trenches or in floors complete all as specified and as directed.

S & F 200 mm bore UPVC [SWR] Junction Single [Single "T"] equal or unequal including jointing with solvent cement complete all as specified and as directed.

S & F 110 mm bore UPVC [SWR] Junction Single [Single "T"] equal or unequal including jointing with solvent cement complete all as specified and as directed.

S & F 75 mm bore UPVC [SWR] Junction Single [Single "T"] equal or unequal including jointing with solvent cement complete all as specified and as directed.

S & F 200 mm bore UPVC [SWR] Bends of any radius including jointing with solvent cement complete all as specified and as directed.

S & F 110 mm bore UPVC [SWR] Bends of any radius including jointing with solvent cement complete all as specified and as directed.

S & F 75 mm bore UPVC [SWR] Bends of any radius including jointing with solvent cement complete all as specified and as directed.

S & F 75 mm bore UPVC [SWR] branch piece, Single [Single "Y"] equal or unequal including jointing with solvent cement complete all as specified and as directed.

S & F 110 mm bore UPVC [SWR] branch piece, Single [Single "Y"] equal or unequal including jointing with solvent cement complete all as specified and as directed.

S & F 110 mm bore UPVC [SWR] Vent Cowl including jointing with solvent cement complete all as specified and as directed.

S & F 75 mm bore UPVC [SWR] Vent Cowl including jointing with solvent cement complete all as specified and as directed.

S & F Rotational Moulded Polythene [HDPE] Water Tanks, Double Layered, ISI Marked, Cylindrical & Vertical Type 1000 Litres Capacity hoisted and fixed in position including provision of 40mm/25mm dia spouts for connecting inlet, outlet, over flow and washout pipes complete all as specified and as directed.

S & F Ball Valves, 25 mm Bore, high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe etc complete all as specified and as directed.

S & F Gun Metal Globe or Gate Valve of Class - I, Pressure Tested of 1.5 MPa, 25 mm bore with iron wheel head, screwed both ends for iron pipe, conforming to IS, ISI Marked complete all specified and as directed.

S & F CPVC Pipes 20 mm outer diameter SDR 11 & Plain CPVC SDR 11 Fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing complete all as specified and as directed.

S & F CPVC Pipes 25 mm outer diameter & Plain CPVC SDR 11 Fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing complete all as specified and as directed.

S & F Two way Bib Cock, 15 mm dia, Chromium Plated, Fancy Type, screwed down for iron pipe and fixed complete all as per Jaquar Catalogue No. ORP-SSF-10041PM or its equivalent in Kohler / Grohe complete all as specified.

S & F Health Faucet Kit with Hand set, flexible hose, wall bracket, non return valve complete as per Jaquar Catalogue No. ALD-573 or its equivalent in Kohler / Grohe complete all as specified.

S & F Angular Stop Cock, 15 mm dia, Chromium Plated, Fancy Type, screwed down for iron pipe and fixed complete all as per Jaquar Catalogue No. FLR-CHR-5053N or its equivalent in Kohler / Grohe complete all as specified.

S & F Pillar Taps, cast copper alloy, Chromium Plated, Fancy Type, 15 mm dia, screwed down high pressure with or with out lettered "Hot" or "Cold" with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as per Hindware italian Catalogue No. F360028CP or its equivalent in Kohler / Grohe complete all as specified.

S & F Vitreous china ware wash hand basin, white, Table Top type complete all as specified and as directed. Make: Model No. ARS-WHT-39903 of Jaquar or equivalent in Kohler / Grohe

S & F Waste Fittings, 32 mm dia, Brass, Chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed.

S & F PVC Connection of 15mm Bore and 600mm long with PTMT check nut and union etc. complete all as specified and as directed.

S & F Vitreous China ware Single Piece Wash Down Water Closet [Pedestal Pattern], Cascade Type, White Colour, Dual Flush Flushing Cistern with UF Soft Close Seat Cover, Hinges, Fixing Accessories and Accessories Set, Cistern fittings, P Trap, etc. complete all as directed and as required at site. Make: Model No. LYS-WHT-38851P of Jaquar or equivalent in Kohler / Grohe

S&F Stailess Steel Paper holder with flap, recessed type fixed complete all as per Jaquar Catalogue No. AHS-1553 or its equivalent in Kohler / Grohe complete all as specified.

S & F Cromium plated Soap Tray complete all as specified and directed (Make:-Jaquar cat No. AKP-35731P or equivalent in Kohler / Cera / Parryware / Grohe / Crabtree

S & F Stainless Steel Soap Dish and holder, Fancy Type complete all as per Jaquar Catalogue No. AKP-35731P or its equivalent in Kohler / Grohe complete all as specified.

S&F Frameless bathroom LED touch sensor mirror wall hanging type size 600X450MM fixed to wall with SS brackets complete all as specified and as directed.

M & L for cutting the existing GI pipe line 150mm dia and inserting GI Tee of 150 X 150 X 100 mm for making new branch connecting of GI Pipe 100mm dia including necessary fittings, excavation, returning, filling and depositing excavated material to a distance not exceeding 50m complete all as specified and as directed

S & F GI pipe, 100mm bore, medium grade, laid in trenches including all necessary fittings and testing complete all as specified and as directed.

S & F GI pipe, 50mm bore, medium grade, laid in trenches including all necessary fittings and testing complete all as specified and as directed.

S & F GI pipe, 25mm bore, medium grade, fixed to walls, ceiling or laid in floors/ trenches including all necessary fittings and testing complete all as specified and as directed.

S & F Sluice Valve, Cast Iron body, Stainless Steel Spindle, Gun Metal Rings including Wheel for operation, Flanged and Drilled, 50 mm bore, confirming to IS – 14846, Class PN –1.6, Non Rising Type, Long Body type including all Joints with Rubber Gasket and Jointing Materials, Bolts, Nuts, Washer complete all as specified and as directed.

S & F Sluice Valve, Cast Iron body, Stainless Steel Spindle, Gun Metal Rings including Wheel for operation, Flanged and Drilled, 100 mm bore, confirming to IS – 14846, Class PN –1.6, Non Rising Type, Long Body type including all Joints with Rubber Gasket and Jointing Materials, Bolts, Nuts, Washer complete all as specified and as directed.

M & L for Construction of Valve Chamber of size 900 X 900 X 900 mm internal size suitable for Sluice Valve, with PCC 1:4:8, Type D2, using 40mm graded aggregate for foundation, 200 mm thick Brickwork with Fly Ash Bricks in Cement Mortar 1:6, 40 mm thick PCC, 1:2:4, Type B1, using 20mm graded aggregate Coping, rendering in CM 1:4, 15 mm thick including provision of Mild Steel Sheet Cover 3 mm thick with 40 X 40 X 6 mm size Angle Iron frame work embedded in concrete with suitable hinges and locking arrangements including two coat of synthetic enamel black paint over a coat of red oxide zinc chrome primer to steel surfaces and including necessary earth work excavation in any type of soil etc., removal of surplus soil off the premises, complete all as specified and shown on drawing CEDD / TD / 119, Sheet No. 1 / 1 dated 20 August 1983, revised up to 21 September 1992.

M & L for Point Wiring complete with 1100 Volts, FRLS Grade, 1.5 Sq.mm, Single Core, Two runs, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable, conforming to IS - 694 drawn through and including heavy duty PVC Conduit, 20 mm dia including all accessories concealed in Walls / Roofs / Floors / Ceiling etc. or surface type / semi concealed type and Metal GI Flush Box of suitable size and thickness including Modular type Base / Grid Frame & Cover Frame for housing Modular Type Switches, Sockets and Regulators etc. concealed in walls, including 1100 Volts, FRLS Grade, 1.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable as earth continuity conductor with colour coding and connecting to Earth Dolly for One Light / Fan Point / Bell Point complete all as specified and as directed.

All as per Serial Item No. 141 above but One 3 Pin Socket Outlet 5 Amps on same Board complete all as specified.

All as per Serial Item No. 141 above but One 3 Pin Switch Socket Outlet 5 Amps on Independent Board complete all as specified.

All as per Serial Item No. 141 above but one 3 Pin Switch Socket Outlet 15 Amps power point on independent board, with 1100 Volts, FRLS grade, 2.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable confirming to IS - 694 and including 1100 Volts, FRLS grade, 2.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable as Earth Continuity Conductor.

All as per Serial Item No. 141 above but one 3 Pin Switch Socket Outlet 15 Amps power point on independent board, with 1100 Volts, FRLS grade, 4 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable confirming to IS - 694 and including 1100 Volts, FRLS grade, 4 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor Cable as Earth Continuity Conductor.

S & F Switch, Modular Type, One Module, Single Pole, One Way, 6 Amps, 230 Volts complete all as specified and as directed.

S & F Ceiling Rose, PVC Body, 65 X 50 mm, Three Terminals, 230 Volts complete all as specified and as directed.

S & F Socket Outlet, 3 Pin, 5 Amps, Modular Type, Two Modules, 230 Volts, complete all as specified and as directed.

S & F Switch Socket Outlet, 3 pin, 16 Amps cum 6 Amps, Modular Type, Two Modules, Multipurpose, 230 Volts complete all as specified and as directed.

S & F Switch Socket Outlet, 3 pin, 6 Amps, Modular Type, Two Modules, Multipurpose, 230 Volts complete all as specified and as directed.

M & L for Sub main wiring with 2 runs of single core 2.5 Sq.mm Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade, ISI Marked, drawing through and including heavy duty PVC Conduit, 20 mm dia with all accessories concealed in Walls / Roofs / Floors / Ceiling etc. or surface type / semi concealed type including One run of 2.5 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade earth continuity conductor complete all as specified and as directed. Note: 3 runs of 2.5 Sq.mm & one run of 20 mm dia PVC Conduit will be measured as one unit.

M & L for Sub main wiring with 4 runs of single core 10 Sq.mm Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade, ISI Marked, drawing through and including heavy duty PVC Conduit, 32 mm dia with all accessories concealed in Walls / Roofs / Floors / Ceiling etc. or surface type / semi concealed type including One run of 10 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade earth continuity conductor complete all as specified and as directed. Note: 5 runs of 10 Sq.mm & one run of 32 mm dia PVC Conduit will be measured as one unit.

M & L for Sub main wiring with 2 runs of single core 6 Sq.mm Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade, ISI Marked, drawing through and including heavy duty PVC Conduit, 25 mm dia with all accessories concealed in Walls / Roofs / Floors / Ceiling etc. or surface type / semi concealed type including One run of 6 Sq.mm, Single Core, PVC Insulated, Unsheathed, Multistranded Copper Conductor cable, 1100 Volts, FRLS Grade earth continuity conductor complete all as specified and as directed. Note: 3 runs of 6 Sq.mm & one run of 25 mm dia PVC Conduit will be measured as one unit.

S & F MCCB DB, VTPN, 8 Way, 415 Volts with DIN Channel, N3 Frame, Double Door with 125 Amps rated bus bar with MCCB as incomer complete all as specified and as directed.

S & F MCB DB, SPN, 8 Way, 240 Volts, with DIN Channel, Double Door with 200 Amps rated bus bar suitable for mounting MCBs flush mounted with wall complete all as specified and as directed.

S & F MCB, TP, 25 to 63 Amps, 10 KA, 'C' Curve, AC, 230 Volts, 50 Hz complete all as specified and as directed.

S & F MCB, SPN, 40 Amps, 10 KA, C Curve, AC, 240 Volts, 50 Hz complete all as specified and as directed.

S & F MCB, SP, 6 to 32 Amps, 10 KA, C Curve, AC, 240 Volts, 50 Hz complete all as specified and as directed.

S & F MCCB 415 V , 16 KA, 4 Pole, 125 Amps capacity complete all as specified and as directed.

S & F Square recessed mounted Flat Panel LED Light suitable for fixing in 2' X 2' Grid False Ceiling of not less than 3600 Lumens output, 6500 K, with high efficiency PMMA diffuser for soft-light and glare free symmetrical illumination with all accessories internally prewired and including connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

S & F Square recess mounted Flat Panel slim LED Light fitting 160mm x 160mm x 16mm height, not less than 1200 Lumens output, 6500 K, with high transmitive diffuser for soft-light and glare free symmetrical illumination with all accessories internally prewired and including connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

S & F Square recess mounted Flat Panel slim LED Light fitting 100mm x 100mm x 16mm height, not less than 1800 Lumens output, 6500 K, with high transmitive diffuser for soft-light and glare free symmetrical illumination with all accessories internally prewired and including connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

S & F Energy efficient Sleek decorative LED Mirror Light Fitting of not less than 1000 Lumens, 2 feet long Surface & Wall mounted with Acrylic / PMMA diffuser for soft glare free light with all accessories internally prewired and including connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm and making good the disturbed surfaces to match with existing complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

S & F Surface & wall mounted Energy efficient LED Tube Light Fitting, of not less than 2000 Lumens output, 5700 K of cool white, with extruded aluminium / CRCA housing and robust construction with necessary acrylic diffuser & integrated electronic driver, all accessories internally prewired and connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

S & F Recess mounted spot light 2 watt 220 volts AC ,warm white colour with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

S & F Energy efficient & Long life Security Light Luminaire, 35 Watt with Pressure die-cast Aluminium housing, IP 65 Protection, heat resistant glass cover, high power LEDs as light source, electronic driver including GI Bracket made out of 32 mm bore GI Tube, Medium Grade of size not exceeding 2.00 m in length and bent to shape required and fixed with 2 Nos of Pole fitting Clamps made out of MS Flat of size 50 X 6mm, bolts, nuts, washers and painting with two coats of aluminium paint over a coat of primer red oxide zinc chrome primer and connecting up with three core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

S & F 15 Watt, warm white ,Focus light fittings, color temp. 4000 K with all accessories internally prewired and including connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

S & F Energy efficient, Low Noise, Ceiling Fan, 1200mm Sweep of any colour as approved, 03 blades, BEE 5 Star Rated, with BLDC Motor, Copper Wound, 350 RPM, with Double Ball Bearing, Conforming to IS - 374, ISI Marked, suitable for operation on Single Phase, 240 Volts, AC, 50Hz, including Down Rod, Canopies, Shackles, Safety Rope, Hanging Clamps, Bushes, having P.F >0.95, Service Value >6.5, Air Delivery >215 CMM, Power Consumption less than 35 Watt, THD less than 5% including provision of Electronic speed control Regulator step type, including connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm, down rods,electronic regulator and accessories complete all as specified and as directed. Note: Ceiling Fan shall be provided with 03 Years onsite replacement warranty. Rate quoted is deemed to be including the same and nothing shall be paid extra on this account.

S & F Exhaust Fan, 300mm Sweep, 1400 RPM, Metal Body, Heavy Duty with Double Ball Bearing, generally Conforming to IS-2312, ISI Marked, suitable for operation on Single Phase, 240 Volts, AC, 50 Hz, including Louvers Shutter / Grill / Guard, BEE 5 Star Rated and of approved colour including connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm and fixing in existing opening and making good the disturbed surface to match with existing and complete all as specified and as directed.

S & F Energy efficient, BEE 5 Star rated Storage type Water Heater [Geyser] 25 Litres Capacity with 2000 Watt Capacity heating element Conforming to IS - 2082, Vertical Storage type with Stainless Steel Inner Tank and ABS Outer Shell complete fixed to wall with suitable expansion fasteners including 02 Nos. of 450 mm long x 15mm dia Stainless Steel braided Flexible Hot & Cold Water connections and 15mm bore Non-Return Valve complete all as specified and as directed. Note: Ceiling Fan shall be provided with 05 Years onsite replacement warranty. Rate quoted is deemed to be including the same and nothing shall be paid extra on this account.

Supplying, laying and testing XLPE insulated and PVC sheathed, armoured heavy duty underground cable, ISI marked with stranded copper conductor 1100 Volt grade of size 3.5 Core, 185 Sq.mm cross section suitable for earthed system, laid in floor / duct or fixed to poles / walls or drawn through pipes / sleeving through pipe in duct, including suitable size Double compression copper stainless steel cable gland, crimping type cable lugs, sockets etc. complete all as specified and as directed.

Supplying, laying and testing XLPE insulated and PVC sheathed, armoured heavy duty underground cable, ISI marked with stranded copper conductor 1100 Volt grade of size 3.5 Core, 70 Sq.mm cross section suitable for earthed system, laid in floor / duct or fixed to poles / walls or drawn through pipes / sleeving through pipe in duct, including suitable size Double compression copper stainless steel cable gland, crimping type cable lugs, sockets etc. complete all as specified and as directed.

Supplying and laying GI pipe, 80mm dia, Light grade fas in cable protection, laid in trenches or fixing on wall / poles of any type, secured with clamps complete all as specified and as directed.

Supplying and laying un–reinforced Precast Concrete Cable Cover, Class LV, Type 1, Flat, of size 250mm x 150mm x 40mm complete all as specified and as directed.

Earthing complete with Galvanised Steel Earth Plate Electrode 600 X 600 X 6 mm thick burried directly in ground [earth pit not less than 2.25 m deep below ground level] with top edge of Plate not less than 1.50 m below normal ground level connected to 32 X 6mm GI Strip [Earth Lead] and GI pipe 50 mm, Medium Grade for earthing lead protection to the extent of maximum 7.5m, Earth Plate Electrode surrounded by 150mm thick packed layers of Charcoal and Common Salt filled in alternate layers, connected to the Plate by means of GI Bolts & Nuts complete all as per Electrical Plate No. 3 of SSR Part – I, connected to panel / DB including testing on completion including main earthing, Charcoal, Common Salt, PCC [1:2:4, Type B1] Pit with RCC 1:2:4, Type B1 Cover, 50 mm thick with 6 Nos, 8 mm dia TMT bars in both ways, MS frame made with 40 X 40 X 6 mm Angle Iron, MS Funnel with 20 mm bore, medium grade GI Watering pipe, wire mesh, earth work excavation, return filling, removal of surplus soil etc. complete all as specified and as directed.

G Srinivas Rao (BID ID -3070540)

SAI KRISHNA ASSOCIATES (BID ID -3061325)

P SRINIVASA RAO (BID ID -3061169)

CIVILEC ENGINEERING WORKS (BID ID -3062186)

KSN PROJECTS (BID ID -3070408)