Construction and Development of Double Section School Building with Bal Vatika, 09 Unit Staff Quarters and other allied development work at Kendriya Vidyalaya, Barkatha, Distt. Hazaribagh, Jharkhand

ABSTRACT OF COST

THE PROPOSED CONSTRUCTION OF KENDRIYA VIDYALAYA CAMPUS AT BARKATHA,

DIST.- HAZARIBAGH, JHARKHAND

SL.NO. PARTICULARS AS PER AS PER DSR- AS PER NON

DSR-2023 (civil) 2025 SOR

1 School building ( G+3)

1.2 Internal Plumbing Works 19,95,281 11,14,791 31,10,072

1.3 Internal Electrical & ELV System Works 1,92,53,184 84,53,916 2,77,07,100

1.4 Internal Fire Fighting System 18,83,166 3,87,972 22,71,138

1.5 Signage Works 4,91,349 4,91,349

2 TYPE -III Quartter (Staff Qtr.) G+1 ( 1 Blocks)

2.2 Internal Plumbing Works 4,06,917 3,29,085 7,36,002

2.3 Internal Electrical & ELV Works 9,32,264 1,43,169 10,75,433

3 TYPE -V Quartter (Principal Quarter G+0)

3.2 Internal Plumbing Works 1,84,889 92,896 2,77,785

3.3 Internal Electrical & ELV Works 5,41,855 1,32,489 6,74,344

4 Site Development and E & M Works

4.02 Substation Building (civil works) 23,16,056 23,16,056

4.04 Boundary Wall & Gate Guard room 2,39,18,209 1,41,929.30 2,40,60,139

4.05 PCC Road , Pathway & Parking 1,31,66,743 1,31,66,743

4.06 Cycle Parking & Covered Pedestrain Shed 33,50,611 33,50,611

4.07 Drinking water kiosk 1,52,371 1,52,371

4.08 Assembly Stage, Sculpture pedestal 3,75,169 3,75,169

4.10 UG Tank with Pump room 1,00,000 Litre 28,87,485 28,87,485

4.11 Septic Tank For (Principal Quarter, Staff Quarter & School Building) 14,28,598 14,28,598

4.12 Landscaping & Horticulture Works 26,13,380 26,13,380

4.13 External Electrical & ELV Works 32,54,239.00 53,73,110 86,27,349

4.14 External Plumbing Works 1,06,68,751 13,31,672 1,20,00,423

4.15 External Firefighting Works 55,44,716.00 1,25,595 56,70,311

Add cost index 10% for Hazaribagh region as per CPWD OM no. 62(H)

Cost i/c GST after Multiplication with multiplying factor 0.973 as per the

CPWD circular on DSR items only 27,87,25,451 3,51,66,904 2,83,39,402 34,22,31,758

SubTotal Including GST [F] :- 34,22,31,758

Digitally signed by PRIYA

PROPOSED CONSTRUCTION OF KV SCHOOL BUILDING (G+3)

ABSTRACT OF COST - CIVIL WORKS

SOR-2023 NON SOR

Sl. No. SOR-2022 DESCRIPTION

A 2 EARTH WORKS 40,28,314.28 -

B 4 CONCRETE WORKS 30,54,193.81 -

C 5 REINFORCED CEMENT CONCRETE WORK 8,17,47,005.84 -

E 8 MARBLE & GRANITE WORK 45,98,271.94 -

K 21 ALUMINIUM WORK 5,826.75 -

L 22 WATER PROOFING 32,96,852.54 -

GRAND TOTAL 16,15,60,209

GRAND TOTAL 16,15,60,209

Digitally signed by PRIYA

BILL OF QUANTITY FOR KV SCHOOL BUILDING (G+3)

Sl. No. DSR-2023 DESCRIPTION UNIT QTY. RATE DSR AMT. NSOR AMT.

A 2.00 EARTH WORKS

1 2.6 Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding

30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated

earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.

2 2.7 Earth work in excavation by mechanical means (Hydralic excavator/manual means)over areas (exceeding

30cm in depth. 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated

earth, lead upto 50m and lift upto 1.5m, as directed by Engineer - in Charge

3 2.10 Excavating trenches of required width for pipes, cables, etc. including excavation for sockets, and dressing

of sides, ramming of bottoms, depth upto 1.5m including getting out the excavated soil, and then returning

the soil as required, in layers not exc

a 2.10.1 All kinds of soil.

i 2.10.1.2 Pipes, cables, etc. exceeding 80mm dia but not exceeding 300mm dia. Metre 100.00 352.15 35,215.00

4 2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not

exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and

5 2.26. Extra for every additional lift of 1.5 m or part thereof in excavation /

banking excavated or stacked materials.

5.2 2.26.2 Ordinary or hard rock Cum 97.58 227.40 22,189.69

6 2.27 Supplying and filling in plinth with sand under floors, including watering,

ramming, consolidating and dressing complete. Cum 449.58 2123.75 9,54,791.00

7 2.28 Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep

and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.

i 2.28.1 All kinds of soil Sqm 1650.00 34.15 56,347.50

8 2.34 Supplying chemical emulsion in sealed containers including delivery as specified

i 2.34.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% Litre 893.92 234.75 2,09,847

9 2.35 Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the

cost of chemical emulsion) :

i 2.35.1.1 Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres / sqm of the

vertical surface of the substructure to a depth of 300mm including excavation channel along the wall &

rodding etc. complete: With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration Metre 385.00 38.90 14,976.50

a) 2.35.3 Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including

drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the

existing floor:

i 2.35.3.1 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration Sqm 192.50 310.05 59,684.63

TOTAL (Carried Over to Summary of Civil Works) 40,28,314.28 0.00

B 4.00 CONCRETE WORKS

1 4.1 Providing and laying in position cement concrete of specified grade excluding the cost of centering and

shuttering - All work up to plinth level :

a 4.1.6 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm

nominal size derived from natural sources) Cum 154.09 7178.75 11,06,196.92

b 4.1.8 1 :4:8 (1 Cement : 4 coarse sand (zone-Ill) derived from

natural sources : 8 graded stone aggregate 40 mm nominal

size derived from natural sources) Cum 232.72 6812.00 15,85,280.08

2 4.3 Centering and shuttering including strutting, propping etc. and removal of form work for :

i 4.3.1 Foundations, footings, bases for columns. Sqm 229.44 392.15 89,974.90

3 4.11 Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand

(zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural

4 4.12 Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement Per 50 kg

as per manufacturer's specification. cement 49.00 18.15 889.35

5 4.13 Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg

per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of

cloth lightly soaked in kerosene oil. Sqm 153.86 146.15 22,486.99

6 4.17 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6

graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size,

well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling &

dressing & finishing the top smooth. Sqm 231.00 749.30 1,73,088.30

TOTAL (Carried Over to Summary of Civil Works) 30,54,193.81 0.00

C 5.00 REINFORCED CEMENT CONCRETE WORK

1 5.9 Centering and shuttering including strutting, propping etc. and removal of form for :

a 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete. Sqm 1240.93 392.15 4,86,632.01

b 5.9.2 Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. Sqm 89.60 842.50 75,488.00

c 5.9.3 Suspended floors, roofs, landings, balconies and access platform. Sqm 5258.27 927.25 48,75,727.77

d 5.9.4 Shelves (Cast in situ) Sqm 146.63 927.25 1,35,961.89

e 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers Sqm 6511.09 736.40 47,94,763.24

f 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts. Sqm 3689.48 961.30 35,46,700.33

g 5.9.7 Stairs, (excluding landings) except spiral-staircases. Sqm 532.88 764.95 4,07,622.73

Digitally signed by PRIYA

Sl. No. DSR-2023 DESCRIPTION UNIT QTY. RATE DSR AMT. NSOR AMT.

h 5.9.15 Small lintels not exceeding 1.5 m clear span, moulding as in

cornices, window sills, string courses, bands, copings, bed

plates, anchor blocks and the like Sqm 1.67 392.15 653.58

i 5.9.16 Edges of slabs and breaks in floors and walls 0.00

j 5.9.19 Weather shade, Chajjas, corbels etc., including edges. Sqm 420.70 951.10 4,00,127.77

2 5.22 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding

all complete upto plinth level.

i 5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. Kg 135383.77 107.85 1,46,01,139.58

3 5.22A Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding

all complete above plinth level.

i 5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. Kg 261892.33 107.85 2,82,45,087.45

4 5.33.1 Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced

cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland

Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS:

9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing

strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost

of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the 2369.09

following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in

design mix shall be payable separately. In case the cement content in design mix is more than 110% of the

specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear

the cost of extra cement.

a) 5.33.1 All works upto plinth level.

i 5.33.1.1 Concrete of M25 grade with minimum cement content of 330 kg /cum Cum 600.00 9504.75 57,02,850.00

b) 5.33.2 All works above plinth level upto floor V level.

i 5.33.2.1 Concrete of M25 grade with minimum cement content of 330 kg /cum Cum 1846.44 9860.40 1,82,06,612.33

TOTAL (Carried Over to Summary of Civil Works) 8,17,47,005.84 0.00

D 6.00 BRICK WORK

1 6.1 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and

i 6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 172.73 7132.25 12,31,924.80

2 6.32 Brick work with clay flyash F.P.S. (non modular) brick of class designation

7.5 in superstructure above plinth level up to floor five level in :

i 6.32.2 Cement mortar 1 :6 (1 cement : 6 coarse sand) Cum 1434.70 9095.05 1,30,48,708.08

3 6.13 Half brick masonry with common burnt clay F.P.S. (non modular) bricks

of class designation 7.5 in superstructure above plinth level up to floor

3.1 6.13.2 Cement mortar 1 :4 (1 cement :4 coarse sand) Sqm 705.40 1123.80 7,92,728.01

4 6.15 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick

s Analysis Based Honey-comb brick work 250 mm thick with common burnt clay bricks

rate DSR 6.23 of class designation 7.5 in super structure above plinth level upto floor V

level with cement mortar 1 :4 (1 cement : 4 coarse sand). Sqm 96.00 2060.80 1,97,836.39

TOTAL (Carried Over to Summary of Civil Works) 1,53,52,515.73 0.00

E 8.00 MARBLE & GRANITE WORK

1 8.2 Providing and fixing 18mm thick gang saw cut ( premoulded and prepolished) machine cut for kitchen

platforms, vanity counters, window sills , facias and similar locations of required size of approved shade,

colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints

treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing,

moulding and polishing to edge to give high gloss finish etc. complete at all levels.

b) 8.2.2 Granite of any colour and shade

2 8.3.2 Providing edge moulding to 18 mm thick marble stone counters, Vanities

etc., including machine polishing to edge to give high gloss finish etc.

complete as per design approved by Engineer-in-Charge. (Granite work) metre 157.13 510.95 80,283.02

3 8.5 Extra for providing opening of required size & shape for wash basin/

kitchen sink in kitchen platform, vanity counter and similar location in

marble/ Granite/ stone work, including necessary holes for pillar taps etc.

including moulding, rubbing and polishing of cut edges etc. complete. Each 88.00 978.70 86,125.60

4 8.9.2 Stone tile (polished) work for wall lining over 12 mm thick bed of cement

mortar 1 :3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm

including pointing in white cement complete. Granite of any colour and shade Sqm 55.56 3617.55 2,00,991.08

5 8.31 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by

the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size

as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement

mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including

pointing in white cement mixed with pigment of matching shade complete.

TOTAL (Carried Over to Summary of Civil Works) 45,98,271.94 0.00

Digitally signed by PRIYA

Sl. No. DSR-2023 DESCRIPTION UNIT QTY. RATE DSR AMT. NSOR AMT.

F 9.00 WOOD, WPC & uPVC WORK

1 9.21.1 Providing and fixing ISi marked flush door shutters conforming to IS :

2202 (Part I) non-decorative type, core of block board construction

with frame of 1st class hard wood and well matched commercial 3 ply

veneering with vertical grains or cross bands and face veneers on both

faces of shutters: (35 mm thick including ISi marked Stainless Steel butt hingesn with necessary screws)

2 9.127.2 Providing & Fixing decorative high pressure laminated sheet of plain

I wood grain in gloss / matt/ suede finish with high density protective

surface layer and reverse side of adhesive bonding quality conforming to

IS : 2046 Type S, including cost of adhesive of approved quality. (1.0 mm thick) Sqm 462.25 897.30 4,14,772.44

3 9.23 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door

shutters (over all area of door shutter to be measured). Sqm 231.12 462.35 1,06,859.49

4 9.24.1 Extra for providing vision panel not exceeding 0.1 sqm in all type of

flush doors (cost of glass excluded) (overall area of door shutter to be

measured): Rectangular or square Sqm 202.10 199.15 40,248.22

5 9.26 Extra for cutting rebate in flush door shutters (Total area of the shutter to

6 9.70.2 Providing and fixing IS : 12817 marked stainless steel butt hinges with

stainless steel screws etc. complete : 100X58X1.90 mm Each 372.00 107.10 39,841.20

7 26.86 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid

door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-

60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non

toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC

solvent cement and screwed with full body threaded star headed SS screws having minimum frame density

of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive

strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A

category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in

position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of

Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately).Note: For WPC

solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be

acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this

account shall be made.

8 26.87 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door

shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium

carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity

index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N

(Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and

resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture

proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body

threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless

steel butt hinges and necessary S.S screws shall be paid separately)

9 9.48.2 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round

bars etc. including priming coat with approved steel primer all complete.Fixed to openings /wooden frames

with rawl plugs screws etc. Kg 6097.68 238.35 14,53,382.03

10 9.96.2 Providing and fixing aluminium sliding door bolts, ISi marked anodised

(anodic coating not less than grade AC 10 as per IS : 1868), transparent

or dyed to required colour or shade, with nuts and screws etc. complete : (250x16 mm) Each 131.00 260.60 34,138.60

11 9.97 Providing and fixing aluminium tower bolts, ISi marked, anodised (anodic

coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed

to required colour or shade, with necessary screws etc. complete :

12 9.103 Providing and fixing bright finished brass 100 mm mortice latch and lock,

ISi marked, with six levers and a pair of anodised (anodic coating not less

than grade AC 10 as per IS : 1868) aluminium lever handles of approved

quality with necessary screws etc. complete. Each 6.00 868.95 5,213.70

13 9.82 Providing and fixing bright finished brass hanging type floor door stopper

with necessary screws, etc. complete. Each 205.00 121.65 24,938.25

14 9.165 Providing and fixing bright /matt finished Stainless Steel handles of

approved quality & make with necessary screws etc all complete.

15 9.84 Providing and fixing aluminium extruded section body tubular type

universal hydraulic door closer (having brand logo with ISi, IS : 3564,

embossed on the body, door weight upto 36 kg to 80 kg and door width

from 701 mm to 1000 mm), with double speed adjustment with necessary

accessories and screws etc. complete. Each 6.00 983.15 5,898.90

16 9.135 Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using

wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete.

16.1 9.135.2 With 12 mm mild steel U beading Sqm 230.04 1228.00 2,82,489.12

Digitally signed by PRIYA

Sl. No. DSR-2023 DESCRIPTION UNIT QTY. RATE DSR AMT. NSOR AMT.

17.00 9.147A Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC

multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum

wall thickness of 1. 70 mm for Series R 1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles

conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section

made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and

lnline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade

fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve

for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary

stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion

welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and

drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with

weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved

drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement

and cross sections

of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh /

Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per

design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately.

Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the

manufacturer for

(i) Sites with basic wind speed > 45 m/sec as per IS 875 - Part 3

(ii) Sites with structure height more than 20m for all wind speeds

9.147.A4 Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for

roller track, wool pile, nylon rollers with SS 304 body.

17.01 9.147.A1.2 Using R3 series with frame (55 mm & above) x (40 mm & above) & sash (30 mm & above) x (55 mm &

above) with zinc alloy (zamak) powder coated handle on every panel along with multi-point locking system

17.02 9.147.C1.1 Fixed window/ ventilator without mullion/ transom. Using R1 series with frame (33 mm & above) x (35 mm &

above). (Height upto 0.90 metre) Sqm 38.34 8247.25 3,16,199.57

18 Providing and installing SGG Evolite Clear (ET 150) Single Glazed Unit (SGU), comprising 6 mm thick

coated glass with coating on Face 2, having a light transmission of 50%, external light reflection of 13%,

internal light reflection of 11%, Solar Heat Gain Coefficient (SHGC) of 0.50 and U-value of 5.0 W/m²K as per

EN 673, complete with all necessary glazing accessories, compatible sealants, labour, handling,

transportation and installation as per approved drawings and manufacturer's specifications.

Classroom Cup Boards & Full ht. Storage

19 9.131.1 Providing and fixing factory made shutters of Pre-laminated particle

board flat pressed three layer or graded wood particle board with one

side decorative finish and other side balancing lamination conforming

to IS: 12823 Grade I Type 11, of approved design, and edges sealed with

water resistant paint and lipped with aluminium 'U' type edge beading

all- round the shutter, including fixing with angle cleat, grip strip, cadmium

plated steel screws, including fixing of aluminium hinges 100x63x4 mm

etc. complete as per architectural drawing and direction of Engineer-inCharge

(Cost of 'U' beading and hinges will be paid for separately).

20 9.167 Providing and fixing 6 mm thick both sides Pre-laminated cement

bonded wood particle board as per IS : 15786:2008 of approved brand

and shade with suitable full threaded steel screws etc. on the backing of

racks, drawer, cupboard, kitchen cabinet under kitchen counter etc. all

complete as per direction of Engineer-in-charge. Sqm 35.16 1010.60 35,532.70

21 9.166.1 Providing and fixing 18 mm thick both sides Pre-laminated cement

bonded wood particle board as per IS : 15786:2008 of approved brand

and shade with suitable full threaded steel screws etc. in partitions, boxes,

shelves, racks and cupboard, kitchen cabinet under kitchen counter etc.

all complete as per direction of Engineer-in-charge (Note: Fittings to be

paid separately).

22 9.170.1 Providing and fixing stainless steel fancy handle of approved make fixed

with SS screws etc. complete as per direction of Engineer-in-charge. (200mm) Each 196.00 186.65 36,583.40

23 9.171 Providing and fixing stainless steel soft closing spring hinges at 0 degree

hinges (hydraulic type) of approved make/brand to cupboard shutters

with full threaded steel screws including making necessary recess in

board and finished etc. complete as per direction of Engineer-in-charge. Each 316.00 272.00 85,952.00

TOTAL (Carried Over to Summary of Civil Works) 95,87,004.76 15,37,825.98

G 10.00 STEEL WORK

1 10.3 Providing and fixing in position collapsible steel shutters with vertical

channels 20x1 0x2 mm and braced with flat iron diagonals 20x5 mm

size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia

steel pulleys, complete with bolts, nuts, locking arrangement, stoppers,

handles, including applying a priming coat of approved steel primer. Sqm Rate only 11439.60 0.00

2 10.5.1 Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset

plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of

approved steel primer. Using M.S. angels 40x40x6 mm for diagonal braces. Sqm 7.56 5804.35 43,880.89

Digitally signed by PRIYA

Sl. No. DSR-2023 DESCRIPTION UNIT QTY. RATE DSR AMT. NSOR AMT.

3 10.6 Supplying and fixing rolling shutters of approved make, made of required

size M.S. laths, interlocked together through their entire length and jointed

together at the end by end locks, mounted on specially designed pipe

shaft with brackets, side guides and arrangements for inside and outside

locking with push and pull operation complete, including the cost of

providing and fixing necessary 27.5 cm long wire springs manufactured

from high tensile steel wire of adequate strength conforming to IS: 4454 -

part 1 and M.S. top cover of required thickness for rolling shutters.

3.1 10.6.1 80x1 .25 mm M.S. laths with 1.25 mm thick top cover Sqm 5.76 3653.20 21,042.43

4 10.15.1 Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-

Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of

required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved

steel primer. Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm

of C.C. 1 :3:6 (1 Cement : 3 coarse sand: 6 graded stone aggregate 20 mm nominal size)

5 10.18 Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140

mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid

shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock

at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

6 10.25 Steel work welded in built up sections/ framed work, including cutting,

hoisting, fixing in position and applying a priming coat of approved steel

primer using structural steel etc. as required.

a 10.25.2 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works KG 8210.00 172.60 14,17,046.00

7 10.27 Providing and fixing carbon steel galvanised ( minimum coating 5 micron)

dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480

N/mm2), counter sunk head, comprising of 10 mm dia polyamide PA 6

grade sleeve, including drilling of hole in frame , concrete/ masonry, etc.

as per direction of Engineer-in-charge.

8 MR-2 Providing, fabricating and fixing of M.S. decorative grill as per design comprising of 16 mm square M.S. rod/

flat/ square bar with frame and supports, covered with 3 mm thick M.S. laser-cut sheet, including cutting,

welding, grinding, edge finishing, fixing in position with necessary clamps/fasteners, and applying one coat of

suitable metal primer, complete in all respects as per approved design and drawing.

TOTAL (Carried Over to Summary of Civil Works) 18,68,082.54 7,04,996.54

H 11.00 FLOORING WORK

1 11.26.1 Kota stone slab flooring over 20 mm (average) thick base laid over and

jointed with grey cement slurry mixed with pigment to match the shade of

the slab, including rubbing and polishing complete with base of cement

mortar 1 : 4 (1 cement : 4 coarse sand) :

2 11.27 Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars

laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse

sand) and jointed with grey cement slurry mixed with pigment to match

the shade of the slabs, including rubbing and polishing complete. Sqm 378.11 2354.70 8,90,327.38

3 11.31 Extra for pre finished nosing in treads of steps of Kata stone/ sand stone

4 11.32 Extra for Kata stone/ sand stone in treads of steps and risers using single

length above normal size up to 2.00 metre. Sqm 172.80 44.15 7,629.12

4 DSR- 11.41A Providing and laying Vitrified tiles in floor in different sizes (thickness to be

specified by the manufacturer) with water absorption less than 0.08% and

conforming to IS: 15622, of approved brand & manufacturer, in all colours

and shade, laid on 20 mm thick cement mortar 1 :4 (1 cement: 4 coarse

sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the

joints with white cement and matching pigments etc. The tiles must be cut

with the zero chipping diamond cutter only . Laying of tiles will be done

with the notch trowel, plier, wedge, clips of required thickness, leveling

system and rubber mallet for placing the tiles gently and easily.

4.1 11.41A.1.3 Double charge vitrified tile polished finish of size (Size of Tile 600 x 1200 mm) Sqm 518.53 1577.15 8,17,798.60

4.2 11.41A.3.1 Glazed Vitrified tiles MatUAntiskid finish of size (Size of Tile 600 x 600 mm) Sqm 453.29 1464.85 6,63,995.45

5 MR-3 Providing and fixing 15 mm thick acid resistant tiles of approved make, size 800 × 2400 mm, on prepared

surface using approved high polymer modified/acid resistant tile adhesive, including preparation and cleaning

of surface, application of adhesive of required thickness, cutting and fitting of tiles to required size and

shape, maintaining proper line, level and alignment, filling and sealing of joints with suitable acid-resistant

epoxy/chemical-resistant grout, complete in all respects as per manufacturer’s specifications and as directed

by the Engineer-in-Charge. Sqm 12.75 3592.53 45,804.76

6 11.48 Grouting the joints of flooring tiles having joints of 3 mm width, using

epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10

kg of hardener and 0.20 kg of resin per kg), including filling / grouting and

finishing complete as per direction of Engineer-in-charge.

Digitally signed by PRIYA

Sl. No. DSR-2023 DESCRIPTION UNIT QTY. RATE DSR AMT. NSOR AMT.

7 11.55.1 Providing and laying flamed finish Granite stone flooring in required

design and patterns, in linear as well as curvilinear portions of the building

all complete as per the architectural drawings with 18 mm thick stone

slab over 20 mm (average) thick base of cement mortar 1 :4 (1 cement: 4

coarse sand) laid and jointed with cement slurry and pointing with white

cement slurry admixed with pigment of matching shade including rubbing,

curing and polishing etc. all complete as specified and as directed by the

Engineer-in-Charge :

Flamed finish granite stone slab Jet Black, Cherry Red, Elite

Brown, Cat Eye or equivalent. Sqm 118.21 3186.70 3,76,683.87

8 11.56 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as

curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab

over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with

cement slurry and pointing with white cement slurry admixed with pigment of matching shade including

rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

11.56.1 Polished Granite stone slab jet black,cherry Red ,Elite Brown,Cat Eye or equivalent sqm 137.50 4481.30 6,16,178.75

9 16.68 Providing and laying 60 mm thick faciory made cement concrete

interlocking paver block of M -30 grade made by block making machine

with strong vibratory compaction, of approved size, design & shape, laid

in required colour and pattern over and including 50 mm thick compacted

bed of coarse sand, filling the joints with line sand etc. all complete as per

the direction of Engineer-in-charge. sqm 684.20 972.00 6,65,042.40

10 16.89 Providing and laying matt finished vitrified tile of size 300x300x9.8 mm

having with water absorption less than 0.5% and conforming to IS: 15622

of approved make in all colours and shades in for outdoor floors such as

footpath, court yard, multi modals location etc., laid on 20 mm thick base

of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns

including grouting the joints with white cement mixed with matching

pigments etc. complete as per direction of Engineer-in-Charge. Sqm 68.37 1455.65 99,522.79

TOTAL (Carried Over to Summary of Civil Works) 1,38,29,238.73 45,804.76

I 12.00 ROOFING

1 12.21 Providing and laying gola 75x75mm in cement concrete M15 grade including finishing with cement mortar 1:3

(1 cement : 3 fine sand) as per standard design in 75x75 mm deep chase. rmt. 309.00 305.15 94,291.35

2 12.55 Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm

x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70

and initial emittance> 0.75 on waterproof and sloped surface of terrace,

laid on 20 mm thick cement sand mortar in the ratio of 1 :4 (1 cement : 4

coarse sand) and grouting the joints with mix of white cement & marble

powder in ratio of 1 :1, including rubbing and polishing of the surface upto

3 cuts complete, including providing skirting upto 150 mm height along

the parapet walls in the same manner. Sqm 350 1703.95 5,96,382.50

3 12.45 Providing and fixing false ceiling at all heights including providing and

fixing of frame work made of special sections, power pressed from M.S.

sheets and galvanized with zinc coating of 120 gms/sqm (both side

inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm

wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre

to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia

x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle

hangers of 25x1 0x0.50 mm of required length with nuts & bolts of required

size and other end of angle hanger fixed with intermediate G.I. channels

45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to

which the ceiling section 0.5 mm thick bottom wedge of 80 mm with

tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre

to centre, shall be fixed in a direction perpendicular to G.I. intermediate

channel with connecting clips made out of2.64 mm dia x 230 mm long G.I.

wire at every junction, including fixing perimeter channels 0.5 mm thick

27 mm high having flanges of 20 mm and 30 mm long, the perimeter of

ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre,

with 25 mm long dry wall screws@ 230 mm interval, including fixing of

gypsum board to ceiling section and perimeter channel with the help of

dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and

finishing to a flush finish of tapered and square edges of the board with

recommended jointing compound , jointing tapes , finishing with jointing

compound in 3 layers covering upto 150 mm on both sides of joint and two

coats of primer suitable for board, all as per manufacturer's specification

and also including the cost of making openings for light fittings, grills,

diffusers, cutouts made with frame of perimeter channels suitably fixed,

all complete as per drawings, specification and direction of the Engineer

in Charge but excluding the cost of painting with :

3.1 12.45.3 12.5 mm thick tapered edge gypsum moisture resistant board Sqm 362.68 1529.10 5,54,568.25

TOTAL (Carried Over to Summary of Civil Works) 12,45,242.10 0.00

J 13 FINISHING WORK

1 13.4 12 mm cement plaster of mix :

2 13.5 15 mm cement plaster on rough side of single or half brick wall of mix:

Digitally signed by PRIYA

Sl. No. DSR-2023 DESCRIPTION UNIT QTY. RATE DSR AMT. NSOR AMT.

3 5.30 Add or deduct for plaster drip course/ groove in or moulding to R.C.C. projections.plastered surface Metre 1412.60 78.40 1,10,747.84

4 13.16 6 mm cement plaster of mix :

4 13.21 Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by per bag of

the manufacturers. 50KG

5 13.26 Providing and applying plaster of paris putty of 2 mm thickness over

plastered surface to prepare the surface even and smooth complete. Sqm 153.75 262.70 40,389.47

6 13.83.2 Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound

) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats

wherever required to achieve even shade and colour. Two coats Sqm 18927.86 142.80 27,02,898.71

7 13.85.3 Applying priming coats with primer of approved brand and manufacture,

having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface

having VOC content less than 50 grams/litre Sqm 18774.11 73.95 13,88,345.77

8 13.45.1 Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28

ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm Sqm 4546.51 223.60 10,16,599.41

9 13.47 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:

i 13.47.1 New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer

10 MR-4 Providing and applying premium quality decorative exterior textured paint finish having natural Travertine

Stone Effect* on external plastered/RCC wall surfaces, using an approved weather-resistant, water-based

acrylic/polymer-modified decorative texture coating system, including: Sqm 483.67 1411.58 6,82,740.47

11 13.50 Applying priming coat :

ii 13.50.3 With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised

iron/ steel works Sqm 1706.78 67.40 1,15,036.90

12 13.62 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even

i 13.62.1 Two or more coats on new work over an under coat of suitable

shade with ordinary paint of approved brand and manufacture Sqm 1706.78 226.25 3,86,158.75

13 13.68.1 French spirit polishing : Two or more coats on new works including a coat of wood filler Sqm 554.69 446.25 2,47,532.20

Expansion joints

14 5.28 Providing and fixing in position 12 mm thick bitumen impregnated fiber. board conforming to IS: 1838, per cm

including cost of primer, sealing compound Grade-A in expansion joints. depth per

15 5.29.2.1 Providing and fixing sheet covering over expansion joints with iron screws

as per design. Aluminium fluted strips 3.15 mm thick. (150 mm wide) Rmt 161.00 567.60 91,383.60

16 26.91 Providing and fixing factory made 18 mm thick single extruded WPC (Wood Polymer Composite) solid plain

white colour board Jali, CNC (Computer numeric control) routed of approved design by Engineer-in -charge

which are machine cut for duct/shaft covering, partitions and facades comprising of virgin polymer of K value

58-60 (Suspension Grade), calcium corbonate and natural fibers (wood powder/ rice husk/ wheat husk) and

non toxic additives(maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and

screw withdrawal strength of 1800 N (Face) minimum compressive strength 50 N/mm2, modulus of elasticity

850 N/mm2 and resistance to spread of flame of Class A category with properties of being termite/borer

proof, water/ moisture proof and fire retardant and fixing on M.S (mild steel) frame made of 25 x 25 x 1.5 mm

square hollow box section including applying a priming coat of approved steel primer, placed at grid made at

1.0 x 1.0 m or as per requirement at site with necessary stainless steel fasteners and SS screws etc., all

complete as per direction of Engineer-In- Charge. Note: M.S (mild steel) framework with priming coat and

necessary SS fasteners and SS screws shall be paid separately.

17 MR-5 Providing, fitting and fixing customised artistic wall mural on building wall using glass mosaic tesserae of

nominal size 20 mm × 20 mm × 4 mm thick, of approved quality, colours, shades, textures and finish,

arranged to reproduce the approved artist’s image, composition and colour scheme, including preparation of

scaled working drawings, colour mapping, numbered installation panels and approved sample; preparation of

sound wall substrate, cleaning, removal of loose material, local repairs and minor surface levelling; supplying

and applying approved white polymer-modified adhesive specifically suitable for glass mosaic and the

specified wall exposure, with compatible primer wherever required; positioning, cutting, shaping, aligning and

firmly bedding mosaic pieces to achieve full adhesive contact; filling joints with approved compatible grout in

selected colours; providing flexible sealant at movement joints, perimeters and junctions as detailed;

finishing edges and corners, removing mounting paper/film where applicable, cleaning and protecting the

completed mural, replacing defective pieces and making good adjoining surfaces; including all materials,

skilled mosaic-artisan labour, tools, equipment, carriage, handling, wastage, staging, scaffolding, working

platforms, safety arrangements and their dismantling at the locations and heights indicated in the drawings,

complete as per approved artwork, specifications and directions of the Engineer-in-Charge.

18 MR-6 Providing and fixing 24 gauge Chicken Wire mesh in junction of block work & RCC works at corner/wall

surface as per direction of Engineer-In-Charge. Sqm 38.50 266.86 10,274.11

Digitally signed by PRIYA

Sl. No. DSR-2023 DESCRIPTION UNIT QTY. RATE DSR AMT. NSOR AMT.

19 MR-7 Providing, fabricating, supplying and fixing factory-manufactured, kiln-fired terracotta jali modules, nominal

size 205 × 205 mm, or other sizes, thicknesses and patterns specified in the approved drawings, including

four-petal, diagonal, geometric or combination designs, of approved quality, shade and manufacture, free

from cracks, distortion and defective edges; assembled in panels within purpose-designed mild steel

supporting framework, comprising perimeter frames, intermediate horizontal and vertical members, angles,

channels, flats, hollow sections, brackets, bearing supports and retaining members of sizes and thicknesses

as per approved structural and shop drawings. Sqm 168.37 5105.21 8,59,551.21

20 MR-8 Providing and fixing factory-made modular toilet cubicle system comprising 12 mm thick compact high-

pressure laminate (HPL) partition panels, pilasters and doors, in approved colour with suede finish, including

doors of size 600 × 1785 mm, divider height 1820 mm and overall height 1995 mm, including 150 mm floor

clearance, with nylon adjustable feet, gravity hinges, coat hooks, door knobs and thumb-turn occupancy

indicators; aluminium U-channels, door-stopper channels and top rails; all screws, wall plugs, noise tape and

necessary fittings, including cutting, drilling, edge finishing, transportation, unloading, shifting, installation and

alignment, complete as per approved drawings, manufacturer’s recommendations and directions of Engineer-

in-Charge. Make: Greenlam Sturdo Essentia Serene or approved equivalent.

TOTAL (Carried Over to Summary of Civil Works) 1,73,21,962.04 33,37,070.81

K 21.00 ALUMINIUM WORK

1 21.1 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up

standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733

and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including

necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc.

Aluminium sections shall be smooth, rust free, straight, mitred and jointed echanically wherever required

including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all

complete as per architectural drawings and the directions of Engineer-in-charge. Glazing and paneling to be

paid for separately) :

a) 21.1.1 For fixed portion.

i 21.1.1.2 Powder coated aluminium (minimum thickness of powder coating 50 micron) KG 5.00 530.90 2,654.50

b 21.1.2 For shutters of doors, windows & ventilators including

providing and fixing hinges/ pivots and making provision

for fixing of fittings wherever required including the cost of

EPDM rubber / neoprene gasket required (Fittings shall be

paid for separately)

1 21.1.2.2 Powder coated aluminium (minimum

thickness of powder coating 50 micron) KG 5.00 634.45 3,172.25

2 21.3 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM

rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-

charge . (Cost of aluminium snap beading shall be paid in basic item):

i 21.3.2 With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) Sqm 0.00 1505.25 0.00

TOTAL (Carried Over to Summary of Civil Works) 5,826.75 0.00

L 22.00 WATER PROOFING

1 22.3 Providing and laying water proofing treatment to vertical and horizontal

surfaces of depressed portions of W.C., kitchen and the like consisting of:

(i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water

proofing compound conforming to IS : 2645 in recommended proportions

including rounding off junction of vertical and horizontal surface.

(ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand)

mixed with water proofing compound in recommended proportion

including rounding off junction of vertical and horizontal surface.

(iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7

kg. per sqm of area.

(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of

PVC sheet should be 100 mm wide and pasted to each other with bitumen

Digitally signed by PRIYA

Sl. No. DSR-2023 DESCRIPTION UNIT QTY. RATE DSR AMT. NSOR AMT.

2 22.7 Providing and laying integral cement based water proofing treatment

including preparation of surface as required for treatment of roofs,

balconies, terraces etc consisting of following operations:

(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement

admixed with water proofing compound conforming to IS. 2645 and

approved by Engineer-in-charge over the RCC slab including adjoining

walls upto 300 mm height including cleaning the surface before treatment.

(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm

to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse

sand) admixed with water proofing compound conforming to IS : 2645

and approved by Engineer-in-charge over 20 mm thick layer of cement

mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing

compound conforming to IS : 2645 and approved by Engineer-in-charge

to required slope and treating similarly the adjoining walls upto 300 mm

height including rounding of junctions of walls and slabs.

(c) After two days of proper curing applying a second coat of cement slurry

using 2.75 kg/ sqm of cement admixed with water proofing compound

conforming to IS : 2645 and approved by Engineer-in-charge.

(d) Finishing the surface with 20 mm thick jointless cement mortar of mix

1:4 (1 cement :4 coarse sand) admixed with water proofing compound

conforming to IS : 2645 and approved by Engineer-in-charge including

laying glass fibre cloth of approved quality in top layer of plaster and

finally finishing the surface with trowel with neat cement slurry and making

pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for

a minimum period of two weeks for curing and for final test. “All above operations to be

done in order and as directed and specified by the Engineer-in-Charge”:

2.01 22.7.1 With average thickness of 120 mm and minimum thickness

TOTAL (Carried Over to Summary of Civil Works) 32,96,852.54 0.00

ALL SUB-HEAD TOTAL 15,59,34,511.06 56,25,698.09

GRAND TOTAL 16,15,60,209

GRAND TOTAL 16,15,60,209

Digitally signed by PRIYA

PROJECT: PROPOSED KENDRIYA VIDYALAYA CAMPUS AT BARKATHA, DIST.- HAZARIBAGH, JHARKHAND

MAIN SCHOOL BUILDING (G+3)

DETAILED ESTIMATE OF INTERNAL PLUMBING

Amount as per Amount as

S.No. DSR -2023 / NS Description Unit Qty. Rate (Rs.)

DSR (Rs.) per MR (Rs.)

Sub- Head - ( I ), Sanitary Fixture & CP Fittings

1 DSR-17.1 Providing and fixing water closet squatting pan (Indian type

W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low

fixtures complete, including cutting and making good the walls

andlevel white P.V.C. flushing cistern, including flush pipe, with

manually controlled device (handle lever) conforming to IS :

7231, with all fittings and floors wherever required :

DSR-17.1.1 White Vitreous china Orissa pattern W.C. pan of size

580x440 mm with integral type foot rests Each 10 6767.4 67,674.00

2 DSR-17.3 Providing and fixing white vitreous china pedestal type water

closet (European type) with seat and lid, 10 litre low level white

vitreous china flushing cistern & C.P. flush bend with fittings &

C.I.brackets, 40 mm flush bend, overflow arrangement with

specials of standard make and mosquito proof coupling of

approved municipal design complete, including painting of

fittings and brackets, cutting and making good the walls and

floors wherever required :

DSR-17.3.1 W.C. pan with ISI marked white solid plastic seat and lid Each 65 8006.6 5,20,429.00

3 DSR-17.4 Providing and fixing white vitreous china flat back or wall corner

type lipped front urinal basin of 430x260x350 mm and

340x410x265 mm sizes respectively with automatic flushing

cistern with standard flush pipe and C.P. brass spreaders with

brass unions and G.I clamps complete, including painting of

fittings and brackets, cutting and making good the walls and

floors wherever required :

DSR-17.4.2 One urinal basin with 5 litre white P.V.C. automatic flushing

DSR-17.4.2 Range of two urinal basins with 5 litre white P.V.C. automatic

flushing cistern Each 4 9612.4 38,449.60

DSR-17.4.3 Range of three urinal basins with 10litre white P.V.C. automatic

flushing cistern Each 4 13417.3 53,669.20

DSR-17.4.4 Range of four urinal basins with 10 litre white P.V.C. automatic

flushing cistern Each 7 18759.95 1,31,319.65

4 DSR-17.7 Providing and fixing wash basin with C.I. brackets, 15 mm dia CP

Brass single hole basin mixer of approved quality and make,

including painting of fittings and brackets, cutting and making

good the walls wherever required:-

(a) White Vitreous China Wash basin size 550x400 mm

with a 15 mm CP Brass single hole basin mixer Each 7 3960.55 27,723.85

5 DSR-18.22 Providing and fixing C.P. brass shower rose with 15 or 20 mm

DSR-18.22.1 150 mm diameter Each 17 222.35 3,779.95

6 DSR-17.31 Providing and fixing 600x450 mm beveled edge mirror of

superior glass (of approved quality) complete with 6 mm thick

hard board ground fixed to wooden cleats with C.P. brass screws

and washers complete. Each 99 1607.95 1,59,187.05

7 DSR-17.72 Providing and fixing PTMT towel ring trapezoidal shape 215 mm

long, 200 mm wide with minimum distances of 37 mm from wall

face with concealed fittings arrangement of approved quality

and colour,weighing not less than 88 gms.

8 DSR-17.73 Providing and fixing PTMT towel rail complete with brackets

fixed to wooden cleats with CP brass screws with concealed

fittings arrangement of approved quality and colour.

DSR-17.73.2 600 mm long towel rail with total length of 645 mm, width

78 mm and effective height of 88 mm, weighing not less

9 DSR-18.65 Providing and fixing PTMT soap Dish Holder having length of

138mm,breadth 102mm, height of 75mm with concealed fitting

arrangements,weighing not less than 106 gms.

Digitally signed Page 1 of 5

Amount as per Amount as

S.No. DSR -2023 / NS Description Unit Qty. Rate (Rs.)

DSR (Rs.) per MR (Rs.)

10 DSR-17.71 Providing and fixing PTMT liquid soap container 109 mm

wide,125 mm high and 112 mm distance from wall of standard

shape with bracket of the same materials with snap fittings of

approved quality and colour, weighing not less than 105 gms.

11 DSR/17.22B Providing and fixing CP Brass Single lever telephonic wall mixer

of quality & make as approved by Engineer in charge.

(a) 15 mm nominal dia Each 17 6940.75 1,17,992.75

12 DSR/17.28 Providing and fixing P.V.C. waste pipe for sink or wash basin

including P.V.C. waste fittings complete.

DSR/17.28.2 Flexible pipe

13 DSR/17.69 Providing and fixing PTMT Waste Coupling for wash basin and

sink, of approved quality and colour.

DSR/17.69.1 Waste coupling 31 mm dia of 79 mm length and 62mm breadth

weighing not less than 45 gms Each 7 115.3 807.10

DSR/17.70 Providing and fixing PTMT Bottle Trap for Wash basin and sink.

DSR/17.70.1 Bottle trap 31mm single piece moulded with height of 270 mm,

effective length of tail pipe 260 mm from the centre of the

waste coupling, 77 mm breadth with 25 mm minimum water

seal, weighing not less than 260 gms. Each 99 367.1 36,342.90

15 DSR/18.49 Providing and fixing C.P. brass bib cock of approved quality

conforming to IS:8931 :

DSR/18.49.1 15 mm nominal bore Each 92 506.8 46,625.60

16 DSR/18.53 Providing and fixing C.P. brass angle valve for basin mixer and

geyser points of approved quality conforming to IS:8931

DSR/18.53.1 15 mm nominal bore Each 184 574.3 1,05,671.20

17 NS Providing, fixing, testing and commissioning of heavy duty chrome

plated brass health faucet conforming to relevant IS/CPWD

specifications, comprising trigger operated hand spray, SS braided

flexible hose of 1.2 m length, wall bracket, 15 mm CP brass angle

valve with wall flange, complete with all accessories, connection to

water supply line, cutting/chasing, making good the wall and

testing complete in all respects.

Approved Make: Jaquar / Hindware / Cera / Kohler / Parryware /

Equivalent approved.

18 NS Providing and fixing white vitreous china counter top wash basin of

approved make, conforming to IS 2556 (Part 4), of size

approximately 550 × 400 mm and 15mm dia CP Pillar tap, complete

with 32 mm dia CP brass waste coupling, cutting/opening in

counter wherever required, fixing with approved sealant, making

good the counter, testing and commissioning complete in all

respects as directed by the Engineer-in-Charge.

Approved Make: Jaquar / Kohler / Hindware / Cera / Parryware /

Equivalent approved.

19 NS Providing and fixing 680 mm long vertical grab bar made of 32 mm

dia stainless steel (SS 304) pipe with satin finish, including

mounting flanges, stainless steel screws, fasteners and necessary

accessories, securely fixed to the wall in the accessible toilet for

persons with disabilities, complete in all respects as directed by the

Engineer-in-Charge.

Approved Make: Jaquar / Hindware / Cera / Parryware / Equivalent

approved. Each 7 4409.00 30,863.00

20 NS Providing and fixing vertical swing grab bar, approximately 738 mm

long × 300 mm wide × 100 mm projection, fabricated from 32 mm

dia AISI 304 stainless steel tube with satin finish, including 3 mm

thick wall-mounting plate, hinged swing-up mechanism with

vertical locking arrangement, six-point wall fixing and necessary

fasteners, complete as directed by the Engineer-in-Charge.

Approved Make: Jaquar / Hindware / Cera / Parryware / Equivalent

Sub- Head - ( II ), Soil, Waste, Vent & Rain Water pipe

Digitally signed Page 2 of 5

Amount as per Amount as

S.No. DSR -2023 / NS Description Unit Qty. Rate (Rs.)

DSR (Rs.) per MR (Rs.)

1 MR Supply fixing and testing UPVC SWR pipe confirming to IS:13592

for waste connection from wash basin and pantry sink to floor

trap or thermosyphonage pipe with solvent cement joints

including all the fittings laid above the fall ceilling connected in

wall etc the shall include wall chiseling making good the same in

cement mortar etc complete include with all necessary support

like GI hangers support GI grip and bolts GI clamp etc in fall

ceilling area as well as supplying and fixing GI slotted angle iron

bracket hangers supports with necessary drilling holes to suit

the insertion of pipe clamps deburring brick work concrete

supports etc as per detailed drawing for supporting soil waste

and rain water pipes and water supply pipes in shaft with

suitable GI clamps GI bolts anchor nuts and washers fixed on

shaft walls, outer walls etc.

2 MR Providing and fixing M.S. holder bat clamps of approved design

including cost of cutting holes and making good the walls etc.

3 MR Providing fixing and testing UPVC SWR plain ring type 90 Deg

Bend with door IS:14735

4 MR Providing fixing and testing UPVC SWR plain ring type 45 Deg

5 MR Providing fixing and testing UPVC SWR plain Single Y Branch

with Door type fitting IS:14735

6 MR Providing fixing and testing UPVC SWR plain Reducing Single Y

Branch Door type fitting IS:14735

7 MR Providing fixing and testing UPVC SWR plain Tee Branch with

Door type fitting IS:14735

8 MR Providing and fixing and testing UPVC single floor trap with all

necessary UPVC pipes connection extension pipe and reducing

tee for water pipe connections from toilet and wash area.

8 MR Providing and fixing 75 mm dia, 3 mm thick Stainless steel

grating with frame for floor traps or drains of required pattern

including cutting and making good the floors complete.

9 DSR /4.1 Providing and laying in position cement concrete of specified

grade excluding the cost of centering and shuttering - All work

up to plinth level:

DSR /4.1.3 1:2:4 (1 cement :2 coarse sand: 4 hard stone aggregate 20mm

and down gauge). Cum 2.00 7878.5 15,757.00

10 DSR/12.22 Making khurras 45x45 cm with average minimum thickness of 5

cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded

stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m

x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1

cement : 3 coarse sand) and a coat of neat cement, rounding the

edges and making and finishing the outlet complete.

11 DSR /12.41 Providing and fixing on wall face unplasticised Rigid PVC rain

water pipes conforming to IS : 13592 Type A, including jointing

with seal ring conforming to IS : 5382, leaving 10 mm gap for

thermal expansion, (i) Single socketed pipes.

Digitally signed Page 3 of 5

Amount as per Amount as

S.No. DSR -2023 / NS Description Unit Qty. Rate (Rs.)

DSR (Rs.) per MR (Rs.)

DSR /12.41.2 110 mm diameter Metre 200 377.4 75,480.00

12 DSR /12.42 Providing and fixing on wall face unplasticised - PVC moulded

fittings/ accessories for unplasticised Rigid PVC rain water pipes

conforming to IS : 13592 Type A, including jointing with seal ring

conforming to IS : 5382, leaving 10 mm gap for thermal

DSR /12.42.1 Coupler

DSR /12.42.3 Single tee with door

DSR /12.42.5 Bend 87.5

13 DSR /12.43 Providing and fixing unplasticised -PVC pipe clips of approved

design to unplasticised - PVC rain water pipes by means of

50x50x50 mm hard wood plugs, screwed with M.S. screws of

required length, including cutting brick work and fixing in

cement mortar 1:4 (1 cement : 4 coarse sand) and making good

the wall etc. complete.

14 DSR /12.44 Providing and fixing to the inlet mouth of rain water pipe cast

iron grating 15 cm diameter and weighing not less than 440

grams. Each 10 54.7 547.00

15 DSR-18.58 Providing and fixing PTMT grating of approved quality and

18.58.1 Circular type

16 N.S Providing, fixing, testing & commisioning of cast iron cleanout

plug with suitable insetkeys for opening male threaded joint

with G.I. socket caulked to HCI soil pipe pipe including cost of

joint material.

Sub- Head - ( III ), Internal Water Supply

1 DSR /18.7 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply, including all

CPVC plain & brass threaded fittings, including fixing the pipe

with clamps at 1.00 m spacing. This includes jointing of pipes &

fittings with one step CPVC solvent cement and testing of joints

complete as per direction of Engineer in Charge.

Internal work - Exposed on wall

DSR /18.7.1 15 mm nominal outer dia Pipes Metre 286.8 -

DSR /18.7.2 20 mm nominal outer dia Pipes Metre 335 -

DSR /18.7.3 25 mm nominal outer dia Pipes Metre 20 401.55 8,031.00

DSR /18.7.4 32 mm nominal outer dia Pipes Metre 75 518.55 38,891.25

DSR /18.7.5 40 mm nominal outer dia Pipes Metre 702.95 -

DSR /18.7.6 50 mm nominal outer dia Pipes Metre 934.15 -

2 DSR /18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply, including all

CPVC plain & brass threaded fittings, i/c fixing the pipe with

clamps at 1.00 m spacing. This includes jointing of pipes &

fittings with one step CPVC solvent cement and the cost of

cutting chases and making good the same including testing of

joints complete as per direction of Engineer in Charge.

Concealed work, including cutting chases and making good the

DSR/18.8.1 15 mm nominal outer dia Pipes Metre 497.8 -

DSR/18.8.2 20 mm nominal outer dia Pipes Metre 260 537.6 1,39,776.00

DSR/18.8.3 25 mm nominal outer dia Pipes Metre 425 627.25 2,66,581.25

DSR/18.8.4 32 mm nominal outer dia Pipes Metre 739.3 -

3 DSR/18.9 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply including all

CPVC plain & brass threaded fittings This includes jointing of

pipes & fittings with one step CPVC solvent cement, trenching,

refilling & testing of joints complete as per direction of Engineer

Pipe running at terrace level

DSR/18.9.6 50 mm nominal inner dia Pipes Metre 50 794.25 39,712.50

DSR/18.9.7 65 mm nominal inner dia Pipes Metre 1674.4 -

Digitally signed Page 4 of 5

Amount as per Amount as

S.No. DSR -2023 / NS Description Unit Qty. Rate (Rs.)

DSR (Rs.) per MR (Rs.)

DSR /18.9.8 80 mm nominal inner dia Pipes Metre 2166.35 -

DSR /18.9.9 100 mm nominal inner dia Pipes Metre 3271.7 -

DSR /18.9.10 150 mm nominal inner dia Pipes Metre 6822.7 -

4 MR Providing and fixing forged brass operated ball valve of full flow

of superior quality having minimum working pressure of 16

4.1 25 mm nominal bore Each 16 3262.00 52,192.00

4.2 50 mm nominal bore Each 2 9015.00 18,030.00

Digitally signed Page 5 of 5

SUMMRY OF ESTIMATE OF INTERNAL ELECTRICAL WORKS & ELV SYSTEM OF SCHOOL BUILDING

(G+3)& ASSEMBLY HALL, KV, BARKATAHA, HAZARIBAGH

SLNO DESCRIPTION DSR AMOUNT

1 SCHEDULE ITEMS (DSR-2025)

i) TOTAL OF SUB-HEAD :1-WIRING 52,55,665.00

TOTAL OF SUB-HEAD :2 MCCB,MCB & DB'S 6,38,717.00

TOTAL OF SUB-HEAD :3 HOT DIP Galvanized CABLE TRAY 74,600.00

TOTAL OF SUB-HEAD :4 EARTHING SYSTEM 2,12,780.00

v) TOTAL OF SUB-HEAD :5 LIGHTNING CONDUCTOR 1,92,347.00

vi) TOTAL OF SUB-HEAD :6 LED LIGHT & FAN 12,51,799.00

vii) TOTAL OF SUB-HEAD :7 MV CABLE LAYING ,JOINTING & END

TERMINATION 20,124.00

viii) TOTAL OF SUB-HEAD :8 SOLAR PV POWER GENERATION 27,14,000.00

ix) TOTAL OF SUB-HEAD :9 LIFT 16,84,225.72

x) TOTAL OF SUB-HEAD :10 UNITERRUPTED POWER SUPPLY 5,05,748.00

xi) TOTAL OF SUB-HEAD :11 HIGH WALL SPLIT AC 4,35,390.00

xii) SUB-HEAD :12 LOW VOLTAGE SYSTEM SCHEDULE ITEMS 49,56,430.00

xiii) SUB-HEAD :13 PUBLIC ADDRESS SYSTEM SCHEDULE ITEMS 13,11,358.00

TOTAL OF SCHEDULE ITEMS (PART-A) (DSR-2025 (ELEC.& 1,92,53,183.72

2 NON SCHEDULE ITEMS NON SCHEULE AMOUNT

i) TOTAL OF NON SCHEDULE ITEMS (PART-B) 83,15,653.00

ii) TOTAL OF PUBLIC ADDRESS SYSTEM (PART-C) 1,38,263.00

TOTAL (NON SCHEDULED ITEMS) (PART-B & C) 84,53,916.00

GRAND TOTAL ( (SCHEDULED ITEMS DSR-2025) PART-A 2,77,07,099.72

GRAND TOTAL ( (SCHEDULED ITEMS DSR-2025) PART-A 2,77,07,099.72

+(NON-SCHEDULED ITEMS ) PART-B

Digitally signed by PRIYA

ESTIMATE FOR INTERNAL ELECTRICAL WORKS & ELV SYSTEM FOR SCHOOL BUILDING (G+3), & ASSEMBLY HALL, KV, BARKATAHA, HAZARIBAGH

Sl. Item Description AMOUNT (NON

No. Code. UNIT QTY RATE SCHEDULE

SCHEDULE ITEMS (DSR-2025) (PART-A)

SUBHEAD :1_WIRING

1 D.S.R Point Wiring in Medium Class PVC Conduit, with Modular type Switch: Wiring for

1.10 light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/ HFFR PVC

( Page insulated copper conductor single core cable in surface/recessed Medium Class PVC

No.-03) conduit, with modular type switch, modular plate, suitable size of GI box and earthing the

point with 1.5 sq.mm. FRLS/HFFR PVC insulated copper conductor single core cable etc as

2 D.S.R Wiring for twin control light point with 1.5 sq.mm FRLS/HFFR PVC insulated copper Point 18 1,803.00 32,454.00

1.11 conductor single core cable in surface / recessed medium class PVC conduit, 2way modular

( Page switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR

No.-03) PVC insulated copper conductor single core cable etc. as required.

3 D.S.R Wiring for light/power plug with 2x4 Sq.mm FRLS/HFFR PVC insulated copper conductor Mtr. 1800 373.00 6,71,400.00

1.12 single core cable in surface/recessed Medium Class PVC conduit along with 1 No. 4 Sq.mm

( Page FRLS/HFFR PVC insulated copper conductor single core cable for loop earthing etc. as

No.-03) required.

4 D.S.R Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of

1.14 FRLS/HFFR PVC insulated copper condcutor, single core cable in surface/ recessed Medium

( Page Class PVC conduit as required.

5 D.S.R Supplying and drawing following pair 0.5 mm dia FRLS/HFFR PVC insulated annealed

1.18 copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC

( Page conduit as required

6 D.S.R Supplying and fixing of following sizes of medium class PVC conduit along with accessories

1.21 in surface/recess including cutting the wall and making good the same in case of recessed

( Page conduit as required.

7 D.S.R Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with

1.22 suitable size of phenolic laminated sheet cover in front

( Page including painting etc. as required.

8 D.S.R. Supplying and fixing following modular switch/ socket on the existing modular plate &

1.24 switch box including connections but excluding modular plate etc. as required.

1.24.4 3 pin 5/6A socket outlet Each 40 136.00 5,440

1.24.6 Telephone socket outlet Each 18 168.00 3,024

9 D.S.R. Supplying and fixing two module stepped type electronic fan regulator on the Each 282 402.00 1,13,364.00

1.25 existing modular plate switch box including connections but excluding modular plate etc. as

( Page required.

10 D.S.R. Supplying and fixing following size/ modules, GI box along with modular base & cover plate

1.27 for modular switches in recess etc. as required.

11 D.S.R. Supplying and fixing suitable size GI box with modular plate and cover in front on surface Each 10 545.00 5,450.00

1.31 or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A

( Page modular switch, connections etc. as required.

12 D.S.R. Supplying and fixing suitable size GI box with modular plate and cover in front on surface Each 116 659.00 76,444.00

1.32 or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and

( Page 15/16 A modular switch, connections etc. as required.

13 D.S.R. Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block Each 300 104.00 31,200.00

1.33 including connections etc. as required

14 D.S.R. Supplying and fixing brass batten/ angle holder including connection etc. as required. Each 85 154.00 13,090.00

15 D.S.R. Installation, Testing and Commissioning of exhaust fan in the existing opening, including

1.50 making good the damage, connection, testing, commissioning etc. as required.

16 D.S.R. Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (

1.55 without independent switch etc.) with 1.5 sq. mm FRLS/HFFR PVC insulated copper

( Page conductor single core cable in surface/ recessed PVC conduit, and earthing the point with

No.-11) 1.5 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required.

17 D.S.R. Supplying and fixing suitable size GI box with modular plate and cover in front on surface Each 210 757.00 1,58,970.00

1.56 or in recess, including providing and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2

( Page nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non

No.-11) residential buildings).

18 D.S.R. Supplying & fixing suitable size GI box with modular plate and cover in front on surface or Each 10 807.00 8,070.00

1.57 in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP

( Page MCB, "C" curve including connections, painting etc. as required.

TOTAL OF SUB-HEAD :1 52,55,665.00

SUBHEAD :2 MCCB,MCB & DB'S

19 D.S.R. Providing and fixing following rating and breaking capacity and pole MCCB with

1.57 thermomagnetic release and terminal spreaders in existing cubicle panel board including

( Page drilling holes in cubicle panel, making connections, Ics=100% Icu and Operational Voltage

No.-11) 690V etc. as required.

20 D.S.R 2.3 SPN DB:- Supplying and fixing following way, single pole and neutral, sheet steel, MCB

( Page distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral

No.-14) bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as

required. (But without MCB/RCCB/Isolator)

2.3.4 16 way, Double door Each 2 3,367.00 6,734.00

21 D.S.R 2.4 TPN DB :- Supplying and fixing following way, horizontal type three pole and neutral,

( Page sheet steel, MCB distribution board, 415 V, on surface/recess,complete with tinned copper

No.-14) bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including

earthing etc. as required. (But without MCB/RCCB/Isolator).

22 D.S.R 2.4 VTPN DB:- Supplying and fixing of following ways surface/ recess mounting, vertical type,

( Page 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted,

No.-14) inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for

mounting MCBs (but without MCBs and incomer ) as required .

(Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)

23 D.S.R MCB:- Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature

2.10 circuit breaker suitable for inductive load of following poles in the existing MCB DB

( Page complete with connections, testing and commissioning etc. as required.

2.10.3 Double pole Each 2 696.00 1,392.00

2.10.5 Triple pole and neutral Each 18 1,301.00 23,418.00

24 D.S.R Supplying and fixing following rating, double pole, single phase and neutral), 240 V,

2.14 residual current circuit breaker (RCCB), having a sensitivity current 30mA in the existing

( Page MCB DB complete with connections, testing and commissioning etc. as required.

25 D.S.R Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at

2.21 least 2 mm thick, and vitreous enamelled white on both sides, and with inscription in single

( Page red colour on front side as required.

TOTAL OF SUB-HEAD :2 6,38,717.00

SUBHEAD :3 HOT DIP Galvanized CABLE TRAY

26 D.S.R Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray

4.6 (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%,

( Page in convenient sections, joined with connectors, suspended from the ceiling with two

No.-26) numbers GI Suspenders i/c base of suitable size GI angle, GI bolts & nuts,fastener etc as

4.6.2 150 mm width x 50 mm depth x 1.6 mm thickness Mtr. 40 803.00 32,120.00

4.6.4 300 mm width x 50 mm depth x 1.6 mm thickness Mtr. 40 1,062.00 42,480.00

TOTAL OF SUB-HEAD :3 74,600.00

SUBHEAD :4 EARTHING SYSTEM

27 D.S.R. Earthing with G.I. earth plate 600 mm X 600 mm X6 mm thick including accessories, and

5.4 ( Page providing masonry enclosure with cover plate having locking arrangement and watering

No.-30) pipe of 2.7 Meter long etc. with charcoal/ coke and salt as required.

i) LT Panel for School Building:- 2 nos

ii) 9 nos. VTPN DB (2 nos. in each Floor) + 1 no. for UPS) = 2x4+2= 10 nos.

ii) 1 no. Lift - 2 nos.

Total G.I.Plate Earthing - 14 nos. Each 14 8,351.00 1,16,914.00

28 D.S.R. Earthing with copper earth plate 600 mm X 600 mm X3 mm thick including accessories,

5.6 and providing masonry enclosure with cover plate having locking arrangement and

( Page watering pipe of 2.7 Meter long etc. with charcoal/ coke and salt as required.

i) For Ups- 2 nos.

ii) Rack- 1 no.

ii) EPBEAX Machine-1 no.

29 D.S.R. Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip Mtr 20 1024.00 20,480.00

5.8 earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as

( Page required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring

No.-31) washer spaced at 50mm)

30 D.S.R. Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth Mtr 70 160.00 11,200.00

5.9 electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as

( Page required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring

No.-31) washer spaced at 50mm)

31 D.S.R. Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing Mtr 30 139.00 4,170.00

5.19 along with existing surface/recessed conduit /sub main wiring /cable as required.

TOTAL OF SUB-HEAD :4 2,12,780.00

SUBHEAD :5 LIGHTNING CONDUCTOR

32 D.S.R. Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. Each 11 609.00 6,699.00

6.1 tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including

( Page holes etc. complete as required.

33 D.S.R. Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for Each 350 148.00 51,800.00

6.6 lightning conductor complete as required.(For horizontal run)

34 D.S.R. Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for Each 165 238.00 39,270.00

6.7 lightning conductor complete as required.(For vertical run)

35 D.S.R. Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, Each 11 140.00 1,540.00

6.10 with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required

36 D.S.R. Earthing with G.I. earth pipe 4.5 Meter long, 40 mm dia including accessories, and Each 11 7,658.00 84,238.00

5.2 ( Page providing masonry enclosure with cover plate having locking arrangement and watering

No.-30) pipe etc. with charcoal/ coke and salt as required.

37 D.S.R. Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth Mtr 55 160.00 8,800.00

5.9 electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as

( Page required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring

No.-31) washer spaced at 50mm)

TOTAL OF SUB-HEAD :5 1,92,347.00

SUB-HEAD :6 LED LIGHT & FAN

Note:- All LED Light fittings LM 79 and LM 80 reports need to be submitted with all

accessories and 50,000.00 hrs shall as burning life. Samples of alltype LED light fixtures

are to be submitted to the Engineering Incharge and each LED Light should have minimum

100lm/W for the approval prior to procurement of light fixtures. Make Havels, Bajaj/

Signify-Philips/Wipro.

38 D.S.R. LED Down lighter (COB Type) (System lumen efficacy ≥105 < 120 lm/Watt ).

Supplying, installation, Testing & Commissioning of LED Recessed/ surface Down lighter

(Round/ Square/ Rectangular) COB Type of following body material and construction as

per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating

voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5 0C to 40 0C,

internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10%

, P.F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) < 19, Flicker free (flicker should

be below 5%), life time (LED, Driver & electrical circuitry), of minimum 50000 Burning

Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K

/4000°K/5700°K/6500°K (As per ANSI Bin), SDCM (Standard Deviation Color Matching)

<3, Maximum power consumption should not more than the specified rating and

Fixture shall be confirming to relevant BIS standards. Manufactures Word Mark/ Name

Engraved/ Embossing/ Screen printing on housing Complete in all respect i/c external

connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core

cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen

efficacy ≥105 and <120 lm/Watt output . LM79 & LM80 Test report and all testing required

for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved

by Engineer-in-Charge as per requirement. (Thermal management: heat sink of

aluminium housing such that LED junction temperature shall not rise above 90°C) Powder

coated die cast /Extruded aluminium Body including trim with Aluminium Reflector .

39 D.S.R. LED Batten light (System lumen efficacy ≥105 <120 lm/Watt).

8.9 Supplying, Installation, Testing & Commissioning of LED surface mounted Batten light of

( Page following body material and construction as per IS : 10322 with driver (Replaceable) as per

No.-45) the requirement with Driver efficiency >85%, Operating voltage AC 140- 270 Volt,

frequency 50/60 hz, Operating temp range -5 °C to 40 °C, internal surge protection of 2.5

KV with Short & Open circuit protection, THD < 10%, P. F.≥0.95, IP20, CRI >80, Flicker

free, (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), of

minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT

3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard DeviationColour

Matching) <3, Maximum power consumption should not more than the specified rating and

Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/

Embossing/ Screen printing on housing. complete in all respect i/c external connections

with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing

etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105 <120

lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per

BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-

Charge as per requirement. (Thermal management: heat sink of aluminium housing such

that LED junction temperature shall not rise above 90°C). Powder coated die cast

/Extruded aluminium Body (Thickness > 1.20 mm)

D.S.R. 18- 22 Watt

D.S.R. 40 Watt

40 D.S.R. LED Street light fixture, powder coated pressure die cast aluminium body (System lumen

8.12 efficacy ≥105 <120 lm/Watt) (to use as building outer light)

Supplying, installation, Testing & Commissioning of Street light (to be use as Building

Outer Light) LED fixture powder coated pressure die cast aluminium body with driver as

per the requirement with Driver efficiency >85%, Input voltage: 140-270 Volt AC,

frequency 50/60 hz, Operating temp range -5°C to 50°C, internal surge protection of 5 KV

L,N,E as per IEC 61000-4-5,61000-3-2, P. F.≥0.95, IP-66,IK-10, CRI >70, under voltage

and over voltage protection, EMIEMC As per CISPR -15, lenses for beam angle as per

IESNA type I/II/III as per the width of the road and the project requirement., suitable to fit

in up to 65mm dia pipe, life time (LED, Driver & electrical circuitry) of minimum 50000

Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation

IES TM-21-11 report,CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin),SDCM

(Standard Deviation Colour Matching) <5, Maximum power consumption should not more

than the specified rating and Fixture shall be of relevant BIS standard complete in all

respect i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper

conductor single core cable and earthing etc. as required with Minimum 5 year OEM

warranty. System lumen efficacy ≥105 <120 lm/Watt output .LM79 & LM80 Test report and

all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall

be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat

8.12.12 sinkWofLED

LIGHT such that LED junction temperature shall not rise above 90°C). Each 8 1,782.00 14,256.00

41 D.S.R. Brush Less Direct Current (BLDC) Fan without Remote:-

Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct

Current (BLDC) Motor, class of insulation: B, 3 nos. metal( Aluminium

alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper

winding, steel/Al body Power Factor not less than 0.9, Service Value (CM/M/W) minimum

as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less

than 10%, suitable for operation with regulator

for speed control and all remaining accessories including safety pin, nut bolts, washers,

temperature rise=75 0C (max.), insulation resistance more than 2

mega ohm, suitable for 230 V, 50 Hz, single phase AC supply, Ceiling Fan compliant to IS

374:2019 fan i/c external connections with 1.5 sq.mm FRLS/HFFR,

9.2.3 PVC insulated

1200mm, copper

service conductor

value single core cable

≥ 6.0 CM/Min/Watt, and earthing

air delivery etc. as(Minimum)

210 CM/Min required. Each 282 2,695.00 7,59,990.00

TOTAL OF SUB-HEAD :6 12,51,799.00

SUB-HEAD :7 MV CABLE LAYING ,JOINTING & END TERMINATION

42 D.S.R. Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of

10.7 1.1 KV grade of following size on wall surface as required.

i) 10.7.1 Upto 35 sq. mm (clamped with 1mm thick saddle) Mtr 90 64.00 5,760.00

ii) 10.7.2 Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp) Mtr 40 151.00 6,040.00

43 DSR Supplying and making end termination with brass compression gland and aluminium lugs

11.1 for following size of PVC insulated and PVC sheathed / XLPE aluminium

TOTAL OF SUB-HEAD :7 20,124.00

SUB-HEAD :8 SOLAR PV POWER GENERATION

44 DSR Solar Photovoltaic Power Plant :- Supplying Installation, Testing and Commissioning

17.1 of on-grid Solar Photovoltaic Power Plant conforming to various applicable standards BIS,

( Page IEC, MNRE guidelines, the Central Electricity Authority Regulations and CPWD

No.-91- Specifications as amended up to date, consisting of Mono/Poly Crystalline silicon solar cells

93) module, net metering facility, necessary control, protections, earthing, cabling, mounting

structure, junction boxes, power conditioning units, Real time online web interfaced Data

Monitoring System, Distribution panels, grid connecting arrangement, conduits, pipes,

cable trays and other accessories etc. as required.

a) High Energy Efficiency Solar Photovoltaic Module of capacity 330 Wp or above,

manufactured in India, conforming to IS 14286/IEC 61215, IS/IEC 61730- Part-1, IS/IEC

61730-Part-2. Solar Photovoltaic Module conversion efficiency shall not be less than 23% at

STC with temperature coefficient of Pmax better than -0.30% per 0C. PV modules used in

solar power plants/ systems must be warranted for their output peak watt capacity, which

should not be less

than 90% at the end of 10 years and 80% at the end of 25 years. Solar Modules shall be

designed to operate in relative humidity upto 100% with temperature between -10 0C and

+85 0C. Further, each PV module used in any solar power project must have Radio

frequency identification tag with information such as name of manufacturer, month and

year of manufacturing, country of origin (separately for Solar cell and module), I-V curve,

Unique Serial No and Model No of the module, Wattage, Im, Vm and FF, name of test lab

issuing IEC certificate.

b)Power Conditioning Unit (PCU) of 350-800 V DC Input voltage range and 415 V AC, three

phase, 4 wire, 50Hz +/- 2.5 Hz, output voltage suitable to generate AC with a variation of

10% at nominal voltage. Power with efficiency not less than 97%, total harmonic distortion

less than 3% and suitable for ambient temperature from 0 to 50 0C, Minimum IP-65 for

outdoor and Minimum IP 21 for indoor, Built-in

meter and data logger, MPPT, switching devices IGBT/MOSFETs and controller

Microprocessor /DSP. PCU/inverter shall be capable of complete automatic

operation including wake-up, synchronization & shutdown. The PCU shall be able to

withstand unbalanced load conforming to IEC standard with shutdown/standby mode. It

must be provided with grid islanding along with manual disconnect pole isolation switch

besides automatic disconnection. Minimum protections: Mains Under / Over Voltage, Over

current, Over/Under grid frequency, Over temperature, Surge voltage induced at output

due to external source,

Short-circuit, Lightening, Anti Islanding (for grid synch. Mode) and other protections as per

applicable standards. LCD/LED display of minimum parameters: DC input voltage, DC

current, AC Voltage and current (all 3 phases, in case of 3 phase), Instantaneous &

cumulative AC output power, Daily DC energy produced and other parameters applicable

standard. Communication interface RS 485 / RS 232

c) Module mounting structure: The roof top solar plant generation units shall be installed

by using supporting Aluminium/Galvanized MS structure (mass of zinc coating shall be as

per IS4759 ) having minimum head room clearance of 2.4 meter above the terrace level /

ground level. The mounting structure would be designed to sustain wind load and seismic

parameter of the site of installation. All the structure shall be

design as per applicable BIS code and the material shall also confirm the applicable BIS

Code. Structural material shall be corrosion resistant and electrolytically compatible with

the materials used in the module frame, its fasteners, nuts and bolts. The suitable

arrangements for maintenance and cleaning shall be provided.

d) Real time online web interfaced Data Monitoring System complete with accessories for

various parameters such as Solar Irradiance, temperature, AC

Output Voltage and current, Output Power, Power factor, DC Input Voltage and Current,

Time Active, Time disabled, Time Idle, Power produced and other

parameters as per standard practices.

e) Array junction box & Main junction box with IP 65 protection and termination

arrangement for incoming and outgoing cable along with glands, lugs and other accessories

etc. as required. Each junction box shall be made of GRP/FRP/Powder Coated Aluminium

/cast aluminium alloy with full dust, water & vermin proof arrangement with High quality

Suitable capacity Metal Oxide Varistors(MOVs) (semiconductor diode with resistant applied

voltage)/ surge arrestors and suitable Reverse Blocking Diodes, isolation switches isolate

the DC input to Inverter, copper bus bar etc.

f) Lightning, surge voltage protection, earthing protection and grid islanding.

g) Cables: Connections & Interconnections by required size IR/UV protected XLPE insulated

copper conductor 1.1 kV grade armored power and control cables(ISI Marked) along with

supplying & fixing of necessary channel/conduit, GI cable trays, supports, lugs, thimble

and other accessories etc. as required.

h) DC Distribution Board And AC Distribution Panel Board: IP65, free standing, metal kWp 50 54,280.00 27,14,000.00

cladded, having copper bus bar, having required protection and control gears, connection-

interconnection, etc. as required.

TOTAL OF SUB-HEAD :8 27,14,000.00

SUB-HEAD :9 LIFT

45 DSR 13 Passenger Lift :- Supplying, Installation, Testing & Commissioning of following

21.1 capacity passenger Machine room less (MRL) lift with regenerative drive as per CPWD

( Page General Specification for Electrical Works (Part-III Lift & Escalator) 2003, BIS Codes, NBC

No.-109- 2016 as amended upto date having provision for barrier free access as per Harmonised

110) Guidelines & Standards for Universal Accessibility in India - 2021 of MoHUA, serving

different floors in the lift shaft as per detailed specifications enclosed and as under

including all other equipment and accessories complete as required:-

(i) Speed-1 MPS

(ii) Floors-5 (G+4)

(iii) Travel -17 Meters (approx.)

(iv) Stops & opening- 5 stops and 5 openings

(v) Controller: A.C. variable voltage & variable frequency

(vi) Automatic rescue device (ARD) complete with dry maintenance free batteries as

vii) Operation: Microprocessor based single automatic push button/simplex selective

collective/duplex collective selective with/without attendant

(viii) Power-415 Volts+10%, 3 phase, 50 Hz, 4 wires system

(ix) Car Enclosure: Stainless steel scratch proof (Moon Rock/Honeycomb/ Hairline Finish)

on all sides and stainless steel decorative ceiling with fans (indirect

throw) and LED fitting.

(x) The car flooring should be smooth and antiskid as approved by engineer-in-charge.

(xi) Type of doors

(a) Car: Power operated, centre opening horizontal sliding stainless steel scratch proof

(Moon Rock/Honeycomb/ Hairline Finish).

(b) Landing doors: stainless steel scratch proof .

(xii) A hand rail not less that 600mm long at 900mm above floor level to be fixed adjacent

to control panel in the lift car.

(xiii)Voice announcement system in the car to

announce the position of the elevator in the hoist way as the car passes or stops at floor

served by the elevator.

(xiv) Closed loop Control System, protection against power fluctuation, self diagnostic

control, Landing doors 2 hours Fire rated, Overload detection and

protection, Overspeed Governer, Dot Matrix LED D & P Indicators In Car & Landings, BMS

Compatibility, tamper proof infrared curtain covering almost the entire height of the lift car

door, Alarm horn, Anti Nuisance Operation, CCTV camera system with 4 MP IP camera,

suitable NVR and HDD for 30 days storage

backup , Firemen switch, 2/3 way intercom, Emergency Stop Switch with battery backup

for fan and light fitting for 1 hour, pit ladder.

(xv) The lift doors shall have a vision panel to enable

persons with hearing impairment to signal for help or assistance in the event of an

(xvi) An appropriate technological support be provided (Through emergency messaging

|services or alarms etc.) to respond to the emergency requirements of person with hearing

impairment or deafness.

(xvii) In case of failure of ARD or other electronic devices, a provision of manual rescue be

TOTAL OF SUB-HEAD :9 16,84,225.72

SUB-HEAD :10 UNITERRUPTED POWER SUPPLY ( UPS)

46 DSR Online UPS- Input supply: Three Phase, Output supply: Three Phase.

No.-190- Supplying, installation, Testing & Commissioning of following capacity at full load (Unity

Power Factor) at operating temperature 0 to 40 0C, Relative humidity 0 to 95%, Online

double conversion true sine wave Uninterrupted hot swapable (allow for the replacement

or addition of battery modules without shutting down the entire system) modular Power

Supply (UPS) system with N+1 modules (N denotes total number of modules required for

rated capacity). The UPS shall include a Rectifier, inverter, battery bank suitable for 30

minutes back up (Battery VAH capacity shall not be less than 1600 VAH per KVA of UPS

rating per Hour backup time) on full load (Battery shall be VRLA, SMF in ABS Container)

and Static Bypass switch along with for manual bypass, suitable isolation transformer for

additional protection against neutral faults etc. (As per correction Slip-1 DSR-568-H E &M-

2025- Chapter- 26) UPS shall have inbuilt phase sequence correction. The UPS systems

offered are to be of the latest technology with Digital Control Microprocessor based for

reliable operation using Insulated Gate Bipolar Transistor (IGBT)'s both for the rectifier &

inverter (3 Level) with PWM (Pulse Width Modulation). The quality of design, manufacturing

and inspection process should confirm to the relevant Inter-national standards such as

IEC/EN/VDE. The operating efficiency of the UPS systems shall be >96% while operating

on battery mode and delivering quality power to the 100% non-linear loads.

Current total harmonic effect(ITHD) on the input grid shall be < 5% at 50 %load. (The

required LC ( inductor (L) and a capacitor (C)) filters shall be included in UPS cost),

extreme power factor kit to be included to limit the input power factor (PF) to 0.99 and

output power factor shall be unity (i.e. kw rating of the UPS shall be kva rating x 1 ),

however UPS shall be suitable to take load at 0.7 laging to 0.7 leading power factor loads.

UPS shall be suitable for incoming supply AC : 3Phase 400V +/-20%, 50 Hz +/-5 Hz, AC

Output voltage: 3Phase 415 Volt, 50 Hz +/- 0.2Hz, Overload capacity of 120% for 10 mins,

Sine wave output. Non condensing, noise level less than 60db at 1 meter distance,

protections: Input Under voltage over voltage, abnormal out voltage, battery over

charging, output over current, short circuit protection, battery deep discharge protection,

10KV surge. UPS must comply with low voltage electromagnetic compatibility (EMC)

achieved as per EN 6204, EN6204 Part I and Part 2, it shall be a Voltage and Frequency

Independent (VFI)-type UPS.

Communication RS232/RS485/SNMP port open protocol for BMS integration, all hardware &

software for iOT Communication as per approved by Engineering in charge. Required

battery racks and interconnecting copper conductor cables of suitable size and connectors

and all required accessories are inclusive of the cost). This system must provide a means

for logging and alarming of all monitored points plus email notification. Forced air-cooling

with integral inbuilt fans with redundancy (if one fan fail UPS should be able to handle at

least 80% of the load, Noise Level 65 DB at 1 meter distance. The system shall be in

compliance IEC 62040- 1,2 & 3, IS: 16242 and CPWD Specification. Display Panel

(minimum) (In-build 5 inch or more LC Display / LED) to display:-

a) Input: Voltage, current, Frequency.

b) Bypass: Voltage, Frequency

c) Output: Voltage, frequency, Current.

d) Battery: 191DELHI SCHEDULE OF RATES (E&M)-2025 Voltage, Capacity

e) Load: KVA, KW, Percentage

f) Temperature: STS, Inverter, PFC.

g) Event Logging & Statistical Data (On LCD/LED): UPS should capture and display up to

3000 events like:Over temperature / DC Bus Fail / Fan Fail / Fuse Fail / Overload / Short-

circuit / Device Fail / InverterFail / Rectifier Fail / Bypass Fail, etc.

h) Statistical Data: No. of power failures /Transfers to Bypass /Total Running time, etc.

i) Mains Mode of Operation/Battery Mode of Operation /Bypass feeding the load/UPS Fault

/Battery charging and discharging, overload, battery voltage and battery capacity.

j)Audible Alarms : Mains Failure,Battery Low Alarm, UPS Overload, Fault, Shutdown, Input

Over, Under Voltage, Output Over, Under Voltage,Battery Over,Under Voltage, Over Load

and short circuit, Over Temperature. The UPS should have QR code which should contain

drawing, test report OEM manual, Geo- Tag of manufacturing location etc. (Make:-

Numeric, Eton, Vertive, APC-Scnider)

26.2.3 30 KVA (Each Power module shall be < 10 KVA) Set 1 5,05,748.00 5,05,748.00

TOTAL OF SUB-HEAD :10 5,05,748.00

SUBHEAD :11 HIGH WALL SPLIT AC

47 DSR Supplying , Installation, Testing and Commissioning of Air

32.2 Cooled Hi Wall split type Air conditioners complete with Indoor unit(IDU), Out door unit

( Page (ODU), surface / concealed copper Refrigerant piping with insulation (closed cell

No.-242- elastomeric nitrile rubber tubular pipe section) upto 3 Mtr (IDU to ODU), copper power

243) cable upto 3.5 Mtr (IDU to ODU) i/c drain pipe R-32/R-410/ R-407 Green Refrigerant,

wireless Remote control, suitable for working between 180- 260V with low & high voltage

cutoff and 50 hz ,1 phase AC supply capable of performing cooling, dehumidification, air

circulation of following capacity with Scroll / rotary compressor. The system shall be able to

deliver 100% of the rated capacity upto 42 0C. Min 5 year Original Equipment Manufacturer

(OEM) warranty both compressor and Printed Circuit Board (PCB). Must comply : Electrical

cable IS 694 or IS 9968 temperature sensing control IS /International Electrotechnical

Commission (IEC) 60730, hermetic compressor IS 10617, heat exchanger IS 11329,

capacitor IS 2993 and motor IS 12615. Complete as per CPWD specification and IS : 1391

Part II 2023. The system shall be able to operate up to 50 0C (out door ambient

temperature). Inverter Type - Cooling only

32.2.3 1.5 TR with 5 Star BEE Rating set 10 43,539.00 4,35,390.00

TOTAL OF SUB-HEAD :11 4,35,390.00

SUB-HEAD :12 LOW VOLTAGE SYSTEM SCHEDULE ITEMS

TELEPHONE SOLUTION

47 D.S.R. Supplying, Installation, Testing & Commissioning of Analog phones having standard Each 18 1,544.00 27,792.00

38.4 feautres like 16 digit LCD display, 2 way speaker, caller ID and number storage facility etc.

( Page complete as required.

48 D.S.R. Supplying and drawing 20 Pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, Mtr 80 344.00 27,520.00

38.5 unarmored telephone cable in the existing surface/ recessed steel/ PVC Conduit etc.

( Page complete as required.

DATA NETWORKING SYSTEM

49 D.S.R. Supplying, installation, Testing and commissioning of following capacity 24 port Layer 2

39.3 indoor Network Switch having features and specifications etc. as mentioned here under: At

( Page least 24 X RJ-45 Gigabit Ethernet Ports and additional 2 X 10G Base -T with 4 X SFP Ports

No.-269) with non-blocking architecture by having Switching capacity of min. 128 Gbps (As per

correction Slip-1 DSR-568-H E &M- 2025) and packet forwarding rate of 95Mpps (As per

correction Slip-1 DSR-568-H E &M- 2025) or higher, 16K MAC table. Console Port, USB

port, Stacking support of min. 4 units (As per correction Slip-1 DSR-568-H E &M- 2025)

per stack. Internal dual AC Power supply, STP, RSTP, MSTP, BPDU Filter, BPDU Restriction,

Min. 9K Jumbo Frame, LBD, IGMP Snooping V1/V2/V3, MLD Snopping V1/V2. IGMP /MLD

Groups 1K or more, IPv4/IPv6 Loopback Interface, 16 L3 IP Interface, Ipv6 ND, VRRPv3,

UDP Helper, ECMP. VLAN: 802.1Ǫ, Port based, Ǫ-in-Ǫ, Multicast VLAN, Protocol VLAN,

VLAN Trunking, DHCP Snopping, Server, server Screening. RADIUS , TACACS+

Authentication, ǪoS: 802.1P, 8 queues per port, ǪoS : WRR, Strict+WRR, WRED, 802.1p.

ACL: MAC based, IPv4C IPv6, TCP/UDP Port number, time based ACL, TFTP Client, SNMP

V1, v2c, v3, SNMP traps, RMON, DHCP server, relay, client, LLDP, LLDP-MED, OAM, Dying

Gasp, 802.3ah, sflow, RIP, OSPF v2/v3, policy based route, SSL, SSH. 6 kV surge

protection on all Gigabit Ethernet ports and on all GE RJ-45 access ports. Certifications:

FCC, CE marked, UL/EN, RoHS and relevant MTCTE{TEC)/BIS compliance/

39.3.1 certification as applicable,

24 port PoE Layer etc. complete

2 Network Switch with PoE as required.

Support of 370W or higher with each copper Each 12 1,25,393.00 15,04,716.00

port supporting 802.3at PoE+ min.

50 D.S.R.- Supplying, installation, Testing and commissioning of following capacity 24 port Layer 3 Each 1 1,93,791.00 1,93,791.00

39.4 (P. Network Switch having features and specifications etc. as mentioned

no-.270) here under: At least 20 X RJ-45 Gigabit Ethernet Ports and additional 4 combo

DSR-2025 10/100/1000 base-t/SFP Ports with additional 4 SFP+ ports non-blocking architecture by

having Switching capacity of min. 128Gbps and packet forwarding rate of 95Mpps or

higher, 16K MAC table. Console Port, USB port, Internal AC Power supply with operating

temperature of 0 to +50 0C. Stacking port with stacking support of minimum 8 units per

stack. 48K Mac address, 9K or more Jumbo frame, ERPS with enabling ring to converge in

less than 50 ms from node or link failure, Static routing, Static, 6to4, ISATAP and GRE,

IPv6 Neighbor Discovery (ND), BGP, ISIS, MPLS, VRRP v2, OSPFv2/v3, PBR, Route

Redistribution, RIPv1/v2/ng, IP Helper all L3 Protocols should support from day 1 for both

IPv6 and IPv4, 802.1x, Port security , Radius CTACACS+ authentication C accounting,

DAD, DAI, DoS attack prevention, SSH, Guest VLAN, IP Access List, MAC Access List.

Multicast: VLAN, PIM-SM, PIMDM, PIM- SDM, PIM-SMv6, DVMRP v3 and MSDP, IGMP C

MLD Snooping, Flow mirroring, IGMP C MLD Snooping Ǫuerier, Per-VLAN IGMP C MLD

Snooping. SNMP, Dual configurations, Multiple images, RMON, LLDP/LLDP-MED, sFlow,

DHCP/BOOTP Client, IPv4/IPv6, Syslog server, Debug command, 802.3ah Ethernet Link

OAM, 802.1ag Connectivity Fault, Y.1731 OAM, 802.1Ǫbb Priority- based Flow Control

(PFC), Dying Gasp, Cable Diagnostics , 6 kV surge protection on all Gigabit Ethernet ports

and on all GE RJ-45 access ports. Certifications: UL, CE, FCC, RoHS, MTCTE, OEM/Product

must be on Trusted Telecom Portal of Department of Telecommunication,Government of

India etc. complete as required.

51 D.S.R. Supplying, Installation, Testing and commissioning of small form-Pluggable (SFP) for

39.6 Network Switches. Must be hot Pluggable, RoHS Complaint, etc. complete as required.

39.6.1 1G SFP Single Mode/Multi Mode Each 13 4,211.00 54,743.00

52 D.S.R. Supplying, Installation, Testing and commissioning of indoor Wireless Access Point for High Each 8 35,559.00 2,84,472.00

39.8 density use having features and specifications etc. as mentioned here under- WiFi6

( Page 802.11ax 574Mbps (2.4GHz) + 2402Mbps (5GHz), WIFI 6 Certified/WI-FI Alliance, MG

No.-273) 2.5G LAN POE Port, having console mangement function (As per correction Slip-1 DSR-

568-H E &M- 2025) factory reset, WPA/WPA2/WPA3™ Personal/Enterprise, WEP 64/128-

bit, SSID broadcast disable, MAC address access control, Internal RADIUS Customizable

Captive Portal, Auto Channel, Works as Access Point, WDS, with AP, Wireless

Client/Mesh,Web (HTTP), Secure Socket Layer (SSL), Traffic control, Support ATF/Fast

Roaming/Band Steering, Supports enhanced security – WPA-PSK/WPA2- PSK/WPA3-PSK

and RADIUS client, and Cipher negotiation, and MAC/ IP ACL for networks, Certifications:

FCC, CE,. marked, UL/EN, RoHS and relenant MTCTE ( TEC)/ BIS Compliance/

certification as applicable (As per correction Slip-1 DSR-568-H E &M- 2025) Works as

Standalone, Compatible with S/W & H/W Controller with addtional features like - Real-Time

Monitoring and Alerts, Rich Advanced Features, Centralized Device Management, Role-

Based Administration, Real-Time Monitoring, VLAN and Access Control, Auto RF

Management and Bandwidth Optimization, Multi-SSID and Captive Portal

Authentication.OEM/Product must be on Trusted Telecom Portal of Department of

Telecommunication, Government of India etc. complete as required

53 D.S.R. Supplying, Installation, Testing and commissioning of indoor Wireless Controller having Each 1 1,13,228.00 1,13,228.00

39.10 features and specifications etc. as mentioned here under- The network controller shall be a

( Page dedicated hardware appliance designed for centralized management of wireless access

No.-274) points, It must support the

management of up to 500 networking devices, The system should be on-premise, ensuring

data privacy and complete control over network configurations. It must include an intuitive

user interface for real-time

monitoring, device discovery, firmware upgrades, scheduling, and mass configuration

deployment. Features such as role-based administration, multi-sitemanagement. AP to

controller communication shall be use of industry standards-based (IEEE or IETF) CAPWAP

or any tunneling protocols as per guidelines of DoT.The controller should support Layer 2

and Layer 3 device discovery, VLAN configuration, MAC ACL groups, IGMP snooping, and

bandwidth optimization. Automatic radio frequency (RF) management and access policy

enforcement are required for reliable wireless performance. The solution must offer a

comprehensive dashboard with network topology, floor plan views, client and device lists,

and alert notifications. For authentication, it should support a range of methods including

database, external RADIUS, LDAP, and passcode or MAC-based access.

It should provide detailed traffic analytics, logs, and customizable reporting for network

visibility and planning. Firmware and configuration backup and

restoration functions must be available, with USBbased log storage supported. Physical

specifications should include a compact form factor with a minimum of one 2.5G Ethernet

port and USB 3.0 port, and it must be MTCTE,CE, FCC, and RoHS certified. The controller

should operate reliably within a 0°C to 40°C temperature range and 10–90% non-

humidity. /Product must be on Trusted Telecom Portal of Department of

Telecommunication, Government of India etc. complete as required.

54 D.S.R. Supplying Installation Testing and Commissioning of 24 port Cat6 Patch Panel loaded. Must Each 13 5,278.00 68,614.00

39.11 be of 1U height with clear label holders and white label with the panel. 24 Ports Cat-6 Patch

(Page No.- Panel should have ETL/UL verification program certificate for compliance with ANSI/TIA-

274) 568.2-D etc. complete as required.

55 D.S.R. Supplying, Installation, Testing and commissioning of following CAT6A Patch Cord should

39.12 have ETL/UL verification program certificate for compliance with ANSI/TIA-568.2-D etc.

(Page No.- complete as required.

39.13.1 Copper Patch Cords of length 1m (3ft) Each 255 173.00 44,115.00

39.13.2 Copper Patch Cords of length 3 m (10ft) Each 154 405.00 62,370.00

56 D.S.R. Supplying, Installation, Testing and commissioning of CAT6A Copper Information Outlet Each 164 302.00 49,528.00

39.15 (IO) with face plate of color as per site requirement, should have ETL/UL verification

( Page program certificate for compliance with ANSI/TIA-568.2-D. All copper Cable and

No.-275) Components should be from same OEM to maintain compatibility and interoperability etc.

complete as required.

57 D.S.R. Supplying, Installation, Testing and commissioning of RJ45 Connector for CAT 6/6A Cables. Each 164 9.00 1,476.00

39.16 RJ45 modular plug supports 4 twisted pairs, 8 positions, 8 connectors. Housing: PC, UL94V-

(Page No.- 2, transparent color, Use for 24- 26 AWG stranded wires etc. complete as required.

58 D.S.R. Supplying, drawing, Testing and commissioning of Cat6A UTP 4 pair, 23 AWG solid copper

39.18 cable in existing conduit/ on surface, U/FTP, LSZH, Non- Plenum, Horizontal (solid) Cable

(Page No.- suitable for high speed data networking application supporting upto 10Gbps over a 100

275) meter channel. The 4 Unshielded Twisted Pairs (UTP) cable with color coded insulation for

easy indentification should have FLAME PROPERTIES i.e. Flammability Test - IEC 60332-1,

Smoke Density - IEC 61034, LSZH standards compliance: ANSI/TIA-568 C.2, ISO/IEC

11801, IEEE 802.3an, RoHS. Delay Skew should be < 45NS. The outer Cable Diameter

should be 7.5 + 2 mm. Cable should have been tested and verified by UL/ ETL etc.

complete as required.

59 D.S.R. Supplying and drawing following core Fiber Optic Cable having corrugated steel armoring.

39.19 The Fiber should be SM Fiber Central -loose tube filled with Thixotropic jelly, duly following

(Page No.- Standards: ISO 11801, IEC 60793-1/60794-1-2, ITU-T-REC G.652D and Telecordia GR-20-

277) core, High quality Electro Chromium Coated Corrugated Steel tape (ECCS ) and HDPE-

Sheath, Operating ambient Temperature should be – 5 0C to +50 0C and Storage

Temperature shall be – 5 0C to +50 0C, Max Attenuation ± 0.36 (db / km) at Operational

Wavelength 1310 nm and ± 0.22 db / km at Operational Wavelength 1550 nm. type of

fiber should be 9/125 / G.652D & Refractive Index should be 1.4670/1.4675. The value for

Mode-filed, Cladding Diameter 9.2 ± 0.4 μm and 125 ± 0.7 μm correspondingly. The

Dispersion value < 3.5 < 18 ps/nm-km and PMD value < 0.2 ps/km and Cable Cutoff

wavelength < 1260 nm i/c splicing & marking etc complete as required.

39.19.1 6 Core Multi Mode Optical Fiber Cable Meter 125 64.00 8,000.00

60 D.S.R. Supply and fixing following port Rack Mount loaded LIU with pigtail, Front-mounted cable

39.21 saddles for jumper management, suitable to manage both splices and terminations, Pre-

(Page No.- assembled shelves in multiple configurations, Rubber fiber slotted bracket built-in, metal

278) splice shelf to protect the fibers, 2 fiber spools built-in for 900μm tight buffered fiber

storing, Capable of storing up to 3 meters of 900μm tight buffered fiber per adapter,

Removable front and rear covers for better access to interior of LIU, Should be Single /

Multi mode LC Type fully loaded. Accessory kit consists of cable ties, mounting ear screws,

and spiral wrap tube etc complete as required.

61 D.S.R. Supplying and fixing Patch Cord of Optical Fiber Multi Mode or Single Mode LC to LC Fiber Each 5 705.00 3,525.00

39.22 Duplex having high precision ceramic ferrule with good concentricity, Fiber corning single

(Page No.- mode G652D, Cable Type 2mm with Mechanical specification Apex Offset < 50 μm, Fiber

278) Height + 100 nm, End-face radius of Curvature 7mm < R <25mm, Repeatability < 0.2 dB,

(As per correction Slip-1 DSR-568-H E &M- 2025) Working ambient Temperature – 5 0C

to +50 0C, Storage Temperature – 10 0C to +50 0C, Length -- 2meter, Type -- LC-LC

Duplex etc complete as required.

62 D.S.R. Supplying and fixing of following size Wall Mount Rack having Fixed Structure with 0.8mm

39.23 CRCA Sheet, completely knocked-down condition (CKD) Shape, Vertical Mounting Rail 1.6

(Page No.- mm with 'U'Marking, Minimum 2 cable entry/exit provision at Top and bottom with rubber

278) protection, Front 5mm Toughened Glass with lock, wall mounting kit, Powder coated Color-

RAL- 7035, complied with UL & RoHS, 2 x 6 sockets 16A power distribution units, 3

numbers closed cable organizer, Hardware mounting screws packet of 20 x 1 number, etc.

complete as required.

39.23.1 6U Rack (to use as equipment Rack for PA System) Each 4 6,939.00 27,756.00

63 D.S.R. Supplying and fixing 42U Rack with 6 inch Castor wheels and front brake Floor Standing Each 1 32,954.00 32,954.00

39.25 Rack with Main Frame Pillar of 1.6mm CRCA Sheet with removable side panels, L- Shape

(Page No.- adjustable Vertical Mounting Rail of 2mm with 'U'Marking completely knocked-down

278-279) condition (CKD) Shape, fitted with 4 number cooling fans, minimum 8nos two line cable

entry/exit provision at top and bottom with rubber protection, Front door 5mm Toughened

Glass with MS frame or MS perforated with lock, Rear MS vented or perforated door,

Powder coated Color- RAL- 7035 or black, complied with UL & RoHS, 2 x 6 sockets 16A

power distribution units, 3 numbers closed cable organizer, Hardware mounting screws

packet of 20 x 1 number, etc. complete as required.

63 5MP/6MP IP IR DOME CAMERA

D.S.R. Supplying Installation Testing and Commissioning of 5/6MP IP IR Dome Camera having

40.5 followingspecifications and features etc :-

( Page 1)Type of Camera: Dome Camera

No.-286) 2) Image Sensor: 1/2.8" or better progressive Scan CMOS get color image even at night

3) Signal System: PAL/NTSC

4) Minimum Illumination: 0.008Lux@ F1.4, AGC ON, 0 lux with IR or better

5) Imaging: 1/3s to 1/30000s Shutter Support, Auto Gain Control , White Balance- Auto,

Back Light Compensation, Multi zone Privacy Masking, HLC, Digital Watermarking.

6) On Screen Display: Camera should display Camera title, Date & Time in live & recorded

7) Signal to Noise Ratio: > 50 dB

8) Day & Night: True Day & Night High Performance Mechanical IR cut filter with auto

switch, IR Source- Inbuilt IR LED's with effective distance upto 50 Mtrs integrated IR 30

Mtrs for colour view in night.

9) Video Compression (Minimum): H.265 or better, Audio:- G.711U/A, G.711Mu, G.726,

10) Wide Dynamic Range: WDR (120dB or more)

11) Digital Noise Reduction: DNR (2D/3D) On/Off

12) Streaming: Triple streaming, configurable

13) Video Streaming & Frame Rates: Triple streaming configurable Main stream: 5/6MP

@25/30 fps, Sub streams: D1@25/30 fps or better

14) Image Setting: Rotate Mode, saturation,

brightness, contrast, sharpness adjustable through client software or web browser

15) Profile Management: User configuration import, export

16) Security: User Authentication, Water Marking

17) Onboard Storage: Camera should support built-in Micro SD/SDHC/SDXC Card slot upto

512 GB. It should be supplied with minimum 128GB memory Card.

18) Recording Management: Format SD, overwrite, storage management, video to NAS

device,19) Edge Analytics : Tripwire, Intrusion, Motion Detection

20) Alarm Trigger : Motion/tampering detection; network disconnection detection; IP

conflict detection; memory card state detection; memory space detection

21) Alarm Support: It should have 1/1 Alarm In/ Out Port

22) Audio Support: It should have 1x Built-In Mic and 1/1 Audio In/ Out Port for external

Mic. and Speaker (As per site requirement) with G.711U/A/ G.711Mu/ AAC/ G.726 audio

23) Network Protocol: SFTP, IPv6, IPv4, DNS,RTCP, NTP, RTP, HTTP, HTTPS, SNMP TCP/IP,

PPPoE, NFS, UDP, ICMP, SSL, DHCP, SMTP, RTSPS, unicast,

40.5.1 5MP/6MP IP IR 2.8/ 3.6/6/8/12 mm fixed lens (as per site requirement) Dome Camera. Each 86 12,800.00 11,00,800.00

5MP/6MP IP IR BULLET CAMERA

64 D.S.R. Supplying Installation Testing and Commissioning of 5MP/6 MP IP IR Bullet Camera having

40.6 following specifications, type of lens and features etc :-

(Page No.- 1) Type of Camera: Bullet Camera

288) 2) Image Sensor: 1/2.8" or better progressive Scan CMOS get color image even at night

3) Signal System: PAL/NTSC

4) Minimum Illumination: 0.006Lux@ F1.4, AGC ON, 0 lux with IR or better

5) Imaging: 1/3s to 1/30000s, Auto Gain Control , White Balance- Auto, Back Light

Compensation, Multi zone Privacy Masking, HLC, Digital Watermarking.

6) On Screen Display: Camera should display Camera title, Date & Time in live & recorded

7) Signal to Noise Ratio: > 50 dB

8) Lens Type & Focus: as given below.

9) Day & Night: True Day & Night High Performance Mechanical IR cut filter with auto

switch, IR Source- Inbuilt IR LED's with effective distance upto 50 Mtrs integrated IR and

30 Mtrs for colour view in night.

10) Video Compression (Minimum): H.265 or better, Audio:- G.711U/A, G.711Mu, G.726,

11) Wide Dynamic Range: WDR (120dB or more)

12) Digital Noise Reduction: DNR (2D/3D) On/Off

13) Streaming: Triple streaming, configurable

14) Video Streaming & Frame Rates: Triple streaming , configurable Main stream:

5MP/6MP @25/30 fps, Sub streams: D1@25/30 fps or better

15) Image Setting: Rotate Mode, saturation, brightness, contrast, sharpness adjustable

through client software or web browser

16) Profile Management: User configuration import, export

17) Security: User Authentication, Digital Water Marking

18) Onboard Storage: Camera should support built-in Micro SD/SDHC/SDXC Card slot upto

512 GB. It should be supplied with minimum 128GB memory Card.

19) Recording Management: Format SD, overwrite, storage management, video to NAS

Edge Analytics: Tripwire, Intrusion, Motion Detection

21) Alarm Trigger : Motion/tampering detection; network disconnection detection; IP

conflict detection; memory card state detection; memory space detection

22) Alarm Support: It should have 1/1 Alarm In/ Out Port

23) Audio Support: It should have 1x Built-In Mic and 1/1 Audio In/ Out Port for external

Mic. and Speaker (As per site requirement) with G.711U/A / G.711Mu/

AAC/ G.726 audio compreesion

40.6.1 5MP/6MP IP IR 2.8 to 3.6/6/8/12 mm fixed lens (as per site requirement outdoor Bullet Each 5 12,525.00 62,625.00

65 D.S.R. Supplying Installation Testing and Commissioning of following Channel Network Video

40.11 Recorder (NVR) with camera licenses to record for all channels having specifications and

(Page No.- features etc as mentioned below :

301) 1) Network Video Recorder Embedded/ Installed OS (Linux) along with Camera Licenses to

record per NVR and to provide a live view, storage and simultaneously

Multi-channel playback of all IP camera or more and must be ONVIF with minimum support

of 384 Mbps incoming Bandwidth.

2) NVR should support video compressions : H.265 or better, H.264, MJPEG.

3) Must support 1 channel RCA Input, 2 channel RCA Output for Two-way Talk with

G.711U/A, G.711u, PCM, G726 audio compressions.

4) Intelligent auto power on when power resumes after power outage.

5) Storage: It should support minimum 8 SATA Slots with 16TB capacity (As per

correction Slip-1 DSR-568-H E &M- 2025)/ Slot and RAID support of RAID 0/1/5/6/10.( 4

SATA ( 32 Channel) & 8 SATA Slot for 64 Channel).(As per correction Slip-1 DSR-568-

6) Connectivity Interface : 2 Nos. x 10/100/1000 Mbps Ethernet Ports, 1x RS485, 1x

RS232, 1x eSATA Port

7) Backup Interface : Its should have 4 Nosx USB port (2x USB3.0, 2xUSB2.0)

8) Video Output Ports: 2x HDMI and 2 VGA

9) Alarm Ports: It should have 16/8 Ch In/ Out ports to connect various type of external

sensors and output devices like hooter/ Siren etc.

10) Email & SMS Altert options: Option for SMS/ Email Alerts to minimum 5 designated

mobile number for power failure, HDD failure, vandalism, tempring, network disconnection

11) Web & Mobile Application: Web, Mobile app ( For iPhone, iPad, Android Phone) for

alerts and viewing.

12) Protocols: HTTP, HTTPS, TCP/IP, IPv4/IPv6, UDP, DHCP, DNS, SMTP, UPnP, IP Filter,

PPPoE, FTP, DDNS, Alarm Server, IP Search, Multicast, Auto Registration, ONVIF (Profile T,

Profile S, Profile G), CGI, SDK and OEM Cloud for remote monitoring without any public IP

13) Standards: CE, FCC, RoHS, BIS Certified

14) Power Supply : Should support AC100-240V, 50/60Hz Power supply.

15) Operating Condition : -5°C to 50°C, humidity 90% (max) (non-condensing)

16) The VMS application shall support all the features & functionalities of the offered

17) VMS should consist Licenses for all channels to record Cameras with General, motion

detection, intelligent, alarm and POS recording modes. VMS should be provided with

Camera Licenses , with no\ dependency of VMS licenses by binding with the MAC

40.11.2 64 Channel Network Video Recorder (NVR) having display split :- Main screen: Each 2 82,600.00 1,65,200.00

66 D.S.R. Supplying, Installation, Testing and Commissioning following capacity Serveillance grade

40.12 Hard Disk with upto 256MB/s Transfer Rate, 256 MB Cache, 7200 RPM Disk Speed, 3.5 inch

( Page form factor, SATA Interface, BSMI, ICES-003/NNB-003, CE, FCC, KC, Maghreb, RCM,

No.-304) UKCA, VCCI, CB-Scheme, TUV, UL Certifications.

67 D.S.R. Access Control System with Face recognition

Supplying, Installation, Testing and Commissioning of Access Control System comprising of

Face and fingerprint Recognition, Smart Card, QR Code, NFC &

PIN Code based Reader, following sizes of 5” IPS TFT Touch Screens, 1GB RAM, 8 GB ROM,

Live Face Detection with anti-spoofing against 2D photograph,

mobile selfie & video, Fake Fingerprint and face Detection Technology, 30,000 Face storage

(1:N) /, 3,000 fingerprint (1:N), QR code 30,000, 30,000 card

storage (1:N), 2 lakh transaction storage, 20,000 image logs, onboard dual camera (colour

& IR) Primary camera min 2MP, Support Face authentication & verification from up to 1

meters, Communication protocols WiFi, TCP/IP, Wiegand

Out, Wiegand IN, USB, MQTT protocol, Blacklist Employee Management, User wise

authentication modes; Built in Lock Control, Mask Detection & Alert (configurable),

40 to 30,000 lux illumination, IP65 for Ingress Protection, Certification: CE, FCC, BIS,

ROHS, etc. Metal Enclosure with battery backup, suitable for mounting on metal

surface/metal frames/ wooden frames/wall/flap barriers including all mounting bracket &

accessories complete etc. as required

41.1.1 5" IPS TFT Touch Screen Each 2 58,306.00 1,16,612.00

67 D.S.R. LED Display

Supplying, Installation, Testing and Commissioning of following size LED display (LED

monitor) industrial grade with 3840x2160 resolution or better, USB playback, bluetooth

and miracast connectivity, 4X HDMI 2.0, DP 1.2, HDR 10/10+, brightness: 500-nits or

better, Video wall mode should be available, contrast ratio: 1200:1, OPS slot, viewing

angle (H/V): 170°/ 170°, response time less than 12ms, Display control shall be on

monitor screen and programmable with remote (remote shall be supplied with system),

Key Board, Optical Mouse, etc. as required.

42.4.3 55 inch or larger (LED DISPLAY) Each 2 82,057.00 1,64,114.00

TOTAL OF LOW VOLTAGE SYSTEM SUB-HEAD :12 49,56,430.00

SUB-HEAD :13 PUBLIC ADDRESS SYSTEM SCHEDULE ITEMS

A) D.S.R. PUBLIC ADDRESS SYSTEM

68 28.3.1 Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, 1 1,32,115.00 1,32,115.00

MP4 player (including 6 zone button paging station) with seamless integration facility with Each

main fire alarm panel for voice evacuation complete as required.

69 28.3.3 Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall 63 1,891.00 1,19,133.00

speakers complete as required Each

70 28.3.7 Supplying, installation, testing & commissioning of digital audio amplifier 75 Watt, 25V rms 5 1,52,368.00 7,61,840.00

operating at 240 Volt AC Supply complete as required. Each

71 28.3.8 Supplying, installation, testing & commissioning of exit point directional sound speaker with 5 10,618.00 53,090.00

voice and integral audio amplifier with selectable sound pulse patterns complete as Each

72 28.3.9 Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with 1 85,450.00 85,450.00

microphone assembly complete as required. Each

B) D.S.R. CABLING & WIRING

73 28.5.3 Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the

existing surface / recessed steel conduit of following pairs, cores and size including

connections and interconnections etc. as required.

74 28.5.3.1 speaker cable Single pair, 2-core, 1.5 sqmm 2400 61.00 1,46,400.00

75 D.S.R. Supplying and fixing of following size Wall Mount Rack having Fixed Structure with 0.8mm

39.23 CRCA Sheet, completely knocked-down condition (CKD) Shape, Vertical Mounting Rail 1.6

(Page No.- mm with 'U'Marking, Minimum 2 cable entry/exit provision at Top and bottom with rubber

278) protection, Front 5mm Toughened Glass with lock, wall mounting kit, Powder coated Color-

RAL- 7035, complied with UL & RoHS, 2 x 6 sockets 16A power distribution units, 3

numbers closed cable organizer, Hardware mounting screws packet of 20 x 1 number, etc.

complete as required.

39.23.3 15U Rack (To use as Equipment Rack PA SYSTEM- FOR ASSEMBLY HALL ) Each 1 13,330.00 13,330.00

TOTAL OF PUBLIC ADDRESS SYSTEM SUBHEAD :13 13,11,358.00

TOTAL OF SCHEDULE ITEMS (PART-A) (DSR-2025 (ELEC.& ELV) 1,92,53,183.72

NON SCHEDULE ITEMS (PART-B)

SUBHEAD :13 (ELECTRICAL & ELV)

LED LIGHT FIXTURES

68 N.S. Note:- All LED Light fittings LM 79 and LM 80 reports need to be submitted with all

accessories and 50,000.00 hrs shall as burning life. Samples of alltype LED light fixtures

are to be submitted to the Engineering In charge and each LED Light should have

100lm/W for the approval prior to procurement of light fixtures.

(N.S.-i) Supply of 9W/10W LED Bulb (Luminous Flux- 600lm, CCT-6500K (Cool W 9/10 watt LED Each 85 104.00 8,840.00

Bulb, B22, 6500 Khite), CRI-80, Rated Voltage- 220V/ 240V. Beam Angle- 120 degree

(N.S.-ii) Supply and fixing of 10 W LED Type Bulk Head luminaire (Metal Body) with minimum Each 10 2,375.00 23,750.00

efficency 100lm/w in comprising of pressure die cast housing, acrylic diffuser, IP 66

protection and complete with ectronic driver etc. dirctly on wall or ceiling including

connection with 1.5 Sq. mm, FRLS PVC cu conductor cable etc. as required with lamp

(N.S.iii) Supply, installation, testing and commissioning of 2ft 10W LED Batten delivering an initial Each 62 621.00 38,502.00

system lumen of 1000 lumens & the luminaire shall be with system efficacy ≥ 100 lm/W.

The housing should be made of Extruded Aluminium with polycarbonate diffuser. The

operating CCT shall be 6500K with CRI of ≥80. The luminaire shall be with BIS Registered

electronic driver with input voltage range of 150 to 270V , PF ≥ 0.9 ,THD ≤ 10%, 50,000

Hrs LED Life with L70 Criteria and Ingress Protection of IP20. Luminaire shall have

minimum surge protection of 2.5KV. The luminaire shall be with following certifications:

LM79 & LM80 issued by LED manufacture along with Photo Biological Safety Standard.

(N.S.iv) Supply, installation, testing & commissioning of 5W LED Foot/Step Light 4000K light, Each 20 1,053.00 21,060.00

Having minimum IP-65 and Efficacy minimum 100 Lm/W, LM6 high pressure die cast

aluminium housing, Glass/Acralic cover surface mounting , clip and surface as required

with complete accessories.

(N.S.v) Supply, installation, testing & commissioning of Environmental friendly, energy saving long Each 16 9,286.00 1,48,576.00

life, vertical surface mounting pressure 50W Warm White in Circular shape Ceiling

suspended decorative LED corrision resistant dia cast alluminium housing ( Light engine )

well glass luminaires with high power LED as light source. 4000K light as required with

complete accessories.

69 N.S. All Exhaust shall be of minimum 2 years of Warranty. Samples of all Fans are to be

submitted to the Engineer-in- charge for the approval prior to procurement of Exhaust

(i) Supply of 230mm 230V AC single phase,1440RPM Exhaust Fan, double ball bearing (Metal Each 9 2,002.00 18,018.00

Body, metalick blade,- Light Duty) exhaust fan as required.

ii) Supply of 300mm 230V AC single phase,1440RPM Exhaust Fan, double ball bearing (Metal Each 20 2,364.00 47,280.00

Body, metalick blade,- Light Duty) exhaust fan as required.

70 N.S. LT CABLE 1.1 KV

Supply of following size of 1.1KV (A2XFY) XLPE / PVC Insulated / PVC sheathed (Heavy

Duty) armoured electric cable with aluminium conductor as ) Extruded PVC Type ST2 Outer

Sheathed, 650 V/1100 V Grade as per IS 7098 (Part 1) 1988 with upto Date

Amendments.Make:- Polycab, Havells, Ultra Tech, KEI, Gloster , AltraVolt.)

a)) SITC of 3.5 Core 25 Sq. mm. XLPE PVC Al. / Ar. Cable 1.1 KV Mtr. 100 497.00 49,700.00

b) SITC of 3.5 Core 50 Sq. mm. XLPE PVC Al. / Ar. Cable 1.1 KV Mtr. 50 856.00 42,800.00

68 N.S. 80L WATER PURIFICATION COOLER

SITC OF 80L Water Purification Cooler (80 Liter | 40 L/Hr) Cooling Capacity & 80L Storage |

Cold Water | Stainless Steel

a)Colour- Stainless Steel

b) Capacity- 80 litres

c) Brand- BLUE STAR,Voltas, Havells

d) Product Dimensions - 8.5D x 66.5W x 114H Centimeters

e)Installation Type- Plumbed

DETAIL SPECIFICATION OF

a)High-Efficiency Cooling System: Delivers 40 litres per hour cooling with an 80-litre

storage tank, ensuring uninterrupted cold water supply for 100–120 users, ideal for

schools, offices, and commercial settings.

b) Dual Tap Dispensing: Features 2 cold water taps to enable simultaneous usage, reducing

wait time during high-demand periods and enhancing user convenience.

c) Optimized Cooling Technology: Powered by R134a refrigerant and a 2.5 Amp system, it

offers energy-efficient cooling while maintaining consistent water temperature throughout

d) SS Body: The stainless steel rust resistant body ensures long-lasting performance, while

the food grade tank delivers pure, contaminant free water. The extra large stainless steel

water tray effectively prevents water splashing and ensures rapid drainage.

e) Multiple Features: A sturdy compressor which guarantees durability and reliability. With

its fast cooling technology, this machine rapidly cools water. It is an environment friendly

machine. This machine is equipped with an openable lid with a locking mechanism for

cleaning and safety purposes.

f) Installation Charges as per Actuals (Whether you buy offline or online, Brand applies

installation charges as per actuals on site) or as per actuals

g) 1-YEAR WARRANTY + 5-YEAR COOLING COIL WARRANTY: Comes with a 1-year

comprehensive warranty and an extended 5-year warranty on the cooling coil for added

Cost of 80L WATER PURIFICATION COOLER Each 8 52,980.00 4,23,840.00

69 N.S. INTERACTIVE TOCH PANEL 75"with inbuilt AI Camera and noise cancelling mic.

SITC OF 75" Intractive Touch Panel with inbuilt AI Camera and noise cancelling mic.

Interactive Flat Panel Digital Board with Stand, 8 GB RAM 128 GB ROM, Ai-Copilot,

Multitouch Screen Display for Teaching & Office Use

A) Brand BIG VUE,Hickvision, LG, Samgung.

B) Colour PRO C)Material

Recommended Uses For Product Office, School E)

Mounting Type Wall Mount

75 Inch 4K AI Interactive Flat Panel with Android 14, 48MP AI Camera, 8-Mic Array, 20-

Point Multi-Touch, 4K UHD Display, Wireless Screen Sharing, Smart Whiteboard & Video

Conferencing etc.

Detail Specification of 75" Intractive Touch Panel with inbuilt AI Camera and

noise cancelling mic.

i) 75" Ultra HD 4K AI Display – Premium IPS display with 3840 × 2160 UHD resolution, anti-

glare toughened glass and 178° viewing angle delivers stunning visuals for classrooms,

conference rooms and training centers.

ii)48MP AI Camera with 8-Mic Array – Built-in 48MP AI Auto-Tracking Camera and 8-array

AI Noise Cancellation Microphones provide professional-quality video conferencing with

automatic speaker tracking and crystal-clear voice pickup

iii) Android 14 Smart Collaboration – Latest Android 14 operating system with AI

Whiteboard, annotation tools, wireless screen sharing, browser, file manager and

productivity applications for interactive learning and business meetings.

iv)20-Point Ultra Fine Multi-Touch – High-precision infrared touch technology enables

multiple users to write, draw and collaborate simultaneously using fingers or stylus pens

with ultra-low response time.

v)Accessories: Power Cord, Remote, USB-C cable, USB A-B cable, HDMI cable, Stylus Pen

vi)Rich Connectivity & Powerful Audio – Dual Band Wi-Fi, Bluetooth, HDMI, USB Type-C,

USB, LAN, OPS Slot and dual 20W stereo speakers ensure seamless connectivity and

immersive audio performance.

vii)Three years on Site Warranty.

ix) Touch Technology: IR, Touch Points: 60, Pen Tip Size: 2.8mm/8mm, Port Connection:

USB Type B x 4, Compatible OS: Windows 8.1/10/11; Chrome OS; MacOS 10.15/11/12

x)This product comes with the Android operating system and includes an OPS slot. The

OPS slot allows the device to function as a dual processing unit and enables memory

expansion. Please note that the OPS module is not included with the system

xi) The above 75" Interactive Touch Panel with inbuilt AI Camera and noise cancelling mic -

4K UHD Display with resolution 3840x2160 pixels. Anti-glare, Anti-Smudge and anti-

blocking design, Inbuilt Dual-OS - in build AI Camera , Windows & Android, D-LED

Backlight, 1.07 billion colour depth, 400 cd/m2 brightness, 4000:1 Contrast Ratio, 60Hz

refresh rate, 178-deg Viewing Angle, 6.5ms response time, 4GB RAM, 32GB Internal

Memory, Android-11 inbuilt OS, 20-point multi touch, Built-in OPS Slot, Input Slots: HDMI

In × 1, LINE In × 1, VGA In × 1, AV In × 1, Type-C × 1, Output Slots: HDMI OUT × 1,

Audio Line Out(3.5 mm jack) × 1, SPDIF OUT × 1, Transmission Inteface: USB 3.0 × 3,

USB 2.0 × 1, TYPEC x 1(11 W), LAN/RJ45 × 1, TOUCH-USB × 1, RS232 × 1. Built-in

2x16Watt Speaker.

Cost of INTERACTIVE TOCH PANEL 75" ) Interactive Touch Panel with inbuilt AI Camera SET 38 1,71,732.00 65,25,816.00

and noise cancelling mic -

N.S.I Supply, fitting fixing and testing of 63A/ FP. 10kA, C Series MCB .(Make:-MCB-LEGRAND- Each 8 2,738.00 21,904.00

DX³/SCHNEIDER- ACTI-9/SIEMENS- BETA GUARD/ L&K- AU VERSION.)

71 N.S. LT PANEL FOR SCHOOL BUILDING (G+3)

Supplying, designing, manufacturing and commissioning in correct alignment position,

effecting proper connection of all incomer and outgoing feeders of LT Panel , unloading at

site, shifting to loaction, fitting, fixing and testing of meter Panel, fabricated out of 2 mm

thick (14SWG) CRCA sheet steel for Load bearing and 1.6 mm or 16 SWG Unload Bearing,

dust and vermin proof with reinforcement of suitable size iron channel, size 75 mm x 40

mm x 6 mm, (or ISMB CHANNEL) with proper lifting arrangement, (IP-42) fully

compartmentalized cubical type (folded joints construction), Floor Mounted, totally

enclosed, accessories, all out going feeders protection & meters as required, factory built

sheet steel enclosed extendable panel and suitable for use on 415V, 3 phase, AC Supply, 4

wire, 50 C/S, system having 25 KA fault capacity, housed with incoming and outgoing

aluminum bus bars, interconnection, interlocking between feeders etc. with indicating

lamps, push buttons, necessary accessories, all out going feeders protection & meters as

The sheet steel under go minimum 7 tanks treatment followed by finishing of powder

coating of minimum 60 micron thickness, duly compartmentalized having accessories

mounted inside the cubical panel, earthing with 2 Nos. earth studs.

The LT Panel shall be totally enclosed, completely dust and vermin proof. Synthetic rubber

gaskets (neoprene/DPDM) between all adjacent units and beneath all covers shall be

provided to render the joints dust proof. All doors and covers shall be fully gasketed and

shall be lockable. Doors shall have concealed hinges. All the doors shall be suitably

reinforced by channel to provide rigidity. Panel shall have suitable cable entry from

bottom/Top and suitable arrangement for aluminum cable termination.

The LT Panel shall be provided with a thermostatically controlled heating arrangement (200

W) to take care of high humidity conditions. A 6/16A socket with sitch as service outlet

(single phase) and 1 no. 10W LED LAMP with holder shall be provided in one of the

compartments as service outlet in the panel. The complete panel shall be fuse less type,

for control circuits 2A SP MCB's to be used.

For the protection of equipment & feeders, switchgear shall be provided with required O/C

& S/C releases. Selection of switchgear rating shall be made on the basis of load current &

fault withstand capacity.

Panel Builder will provide shop drawing SLD & GA drawing along with BOM with CAT. No. of

each and every components and switch gears of Meter Panel for approval of Consultant or

concirned department. Inspection of the Meter Panel shall be carried out at Panel Builder's

factory by the Consultantor departmental engineers before final delivery for that all

arrangements shall be made by the contractor.

Location :- IN SUB STATION BUILDING

The Name Plate for each feeder must be in Anodized Aluminium Sheet.

The Panel Builder must be CPRI approved. Panel builder must produce test certificate for

Type Tested & Short Ckt withstand capacity as per IEC-60439-II from CPRI.

MCCB:- L&K-DSine/ LEGRAND-DPX³/SCHNEIDER-NSX/ SIMENS- 3VJ-3WJ

MCB- C Series 10kA _ Legrand- DX³/Schneider- ACTI-9/Siemens- Beta Guard/ L&K- AU

Panel Size - As per Drawing and shall be provided at the time of work order.

1 Set of Fabrication part of LT Panel & busbar system, with AL. bus bar and

interconnection FRLS cables) in 14 SWG (2 mm Thick) CRCA Sheet Steel enclosure (IP-42)

without components. Name of Panel builders:- EAP Kolkata, Green Galaxy Kolkata, A.C.

Popwer Kolkata, JMD, Kokar, Ranchi, Meditiron, SIRDO, BIT Meshra, Ranchi. Amichand

Technology, Jamshedpur.

1 Sets Multifunction Meter having LED mete display accuracy Class 1 as per IEC 62053-21,

should have an active RS-485 port, in built RTC, Aux Supply: 44-277Vac/dc. Parameters:

Volts, Amps, PF, THD, F, W, Wh, VA, VAh, Var, Varh, Runhrs, Onhrs Interrupts, THD for

V&I per phase, individual harmonics for V&I upto 15th level complying with IEC61557-12.

Min/Max for eight parameters. Sampling rate: 64 samples per cycle.

3 Nos. CT of different power as per incomer & out going /5VA -5 class one Epoxy resin cast

CT (3 Nos.)=1 Set.

3 Sets Phase indicating light shall be protected by 2 Amps SP MCB's for incomer &

1 no. 400A/FP/MCCB (36kA) with adjustable Thermomagnetc Release , with S/C, O/L

protection, alkong with ON OFF TRIP indication and with extended front rotary handle and

spreader links in Both End. (Cable Size :-1 Run 3.5 C 240 SQ MM AL. AR. Cable.)

OUT GOING FEEDERS WITHOUT DG

5 nos. 100/P MCCB (25kA) with adjustable thermomagnetc release type with S/C & O/L

protection, and front rotary Handle and spreader links in both end. (For Power All Floor

VTPN DB and 1 no. as spare.(Cable Size :- 1 Run 3.5 C 50 SQ MM AL. AR. Cable.)

1 no. 63/P MCCB (25kA) with adjustable thermomagnetc release type with S/C & O/L

protection, and front rotary Handle and spreader links in both end. (1 no. as spare (Cable

Size :- 1 Run 3.5 C 35 SQ MM AL. AR. Cable.)

1 no. 25/P MCCB (25kA) with adjustable thermomagnetc release type with S/C & O/L

protection, and front rotary Handle and spreader links in both end as future use.

FEEDERS WITH DG SUPPORT

Provision of Mechnical interlocking between 200A/FP/25KA MCCB as common incoming for

essential load and 1 No. of 200A on load TPN Change over as D.G incomer, in such a way

so that the two supplies are not parallel at any time.

1 no. 200A/FP/MCCB (25kA) with adjustable Thermomagnetc release , with S/C, O/L

protection, alomg with extended front rotary handle and spreader links in both ends.

1 No. 200A TPN on load Manual ON Load Change over panel mounted open execution type

and suitable bus arrangement for Cable termination. (Cable Size :- 1 Run 3.5 C 120 SQ MM

AL. AR. Cable.) Make-L&K/Sucomo/ Legrand.

10 nos. 63/P MCCB (25kA) with adjustable thermomagnetc release type with S/C & O/L

protection, and front rotary Handle and spreader links in both end. (4 nos. for Light VTPN

DB, 2 nos. for Lift Machines (1 working and one future use), 1 No. for UPS, 1 no. for fire

fighting, , 1 no. for Roof Top Solar Panel Feeder,and 1 no. as spare (Cable Size :- 1 Run

3.5 C 25 SQ MM AL. AR. Cable.)

2 nos. 25/P MCCB (25kA) with adjustable thermomagnetc release type with S/C & O/L

protection, and front rotary Handle and spreader links in both end. 1 no. for Pump Panel

and 1 no. as spare

3 no. 32A DP MCB C Series of 10 kA

Total Cost of LT Panel. Set 1 8,07,039.00 8,07,039.00

72 N.S. EPABX SYSTEM

EPABX SYSTEM along Server Software and Unified Communication Server

Software and Hot StandBy Server Software System-Epabx

Supply, fitting, fixing, commissioning and testing of IP based 100% non-blocking IP EPABX Set 1 1,32,808.00 1,32,808.00

System should be a IP Compatible with rich feature set of the system and can be

connected with pure Voice over IP (VoIP) communication network across corporate Local

and Wide Area Networks (LAN and WAN) as & when required.

• IP PBX SYSTEM along Server Software and Unified Communication Server Software and

Hot StandBy Server Software Pabx System-Epabx

• Central Processing Unit: The system main software should be open architecture based.

The CPU of main system shall be 32 bit processor working at 2.0 GHz or better. The

system should be Wall mountable.

• System Architecture should be latest pure IP and should be wall Mountable

• Meet-me conference 30 party X 2 from day 1 must be available.

• Must Support Unified Communications •

Equipped with 20 Analog extensions , 1 IP Extensions loaded from day expandable upto 2

IP Extensions, VOIP CARD in built charger, battery with one our back up facitity.

• 20 Analog Trunk Ports, 1 SIP Trunk , 01 Ports Auto Attendant- EPABX .

Make:- Avaya/Syntel by Arvind Telecom/Alacatel

TELEPHONE SOLUTION

73 N.S.I Krone box:-

Providing, fixing, connecting & testing of Krone box (Telephone Tag Block) in a

thermoplastic, IP 65 (weather proof) enclosure, internally embedded gasket, anti corrosive,

insulated and shock proof with provision for cable through IP 65 glands complete in all

respects. (Make : Matrix/Alcatel/Avaya.

i) 10 pair Tag Block (krone Box) (136 mm x 253 mm x 115 mm) Each 2 1,328.00 2,656.00

ii) 50 pair Tag Block (krone Box) (300 mm x 300 mm x 70 mm) Each 1 3,064.00 3,064.00

TOTAL OF NON SCHEDULE ITEM (PART-B) 83,15,653.00

74 N .S ( PUBLIC ADDRESS SYSTEM) PART-C

(N.S.-i) SITC of Handheld combo variable frequency, high quality, UHF band frequency dual Each 2 38,899.00 77,798.00

wireless Microphone System, 80 selectable UHF Channels. UHF Operating Frequency Range-

583-683 MHZ, back light display for frequency. Separate LCD display doe channels, high

quality capsul in handheld mic, XLR balanced and unbalaced out, flight case. (1 no for

Podium at Assdembly Hall & 1 no. in Principal room for announcement)

(N.S.-ii) WOODEN PODIUM FOR ASSEMBLY HALL

SITC of wooden podium / lectern made of high-quality engineered wood / commercial No 1 60,465.00 60,465.00

plywood with premium laminate finish, sturdy construction, sloping top writing surface,

concealed cable management and provision for keeping laptop/documents, complete with 1

No. flush-mounted connectivity dataplate comprising 1 No. HDMI female port, 1 No. VGA

(15-pin) female port, 1 No. 3.5 mm AUX audio input socket and 1 No. 5/6A, 230V AC

power socket with proper earthing. The podium shall include all necessary internal cabling,

connectors, mounting accessories and hardware as required

TOTAL OF NON SUBHEAD ITEM (PART-C) 1,38,263.00

TOTAL (NON SCHEDULED ITEMS) (PART-B & C) 84,53,916.00

GRAND TOTAL ( (SCHEDULED ITEMS DSR-2025) PART-A +(NON-SCHEDULED 2,77,07,099.72

GRAND TOTAL ( (SCHEDULED ITEMS DSR-2025) PART-A +(NON-SCHEDULED 2,77,07,099.72

PROJECT: PROPOSED KENDRIYA VIDYALAYA CAMPUS AT BARKATHA, DIST.- HAZARIBAGH, JHARKHAND

MAIN SCHOOL BUILDING (G+3)

DETAILED ESTIMATE OF FIRE FIGHTING AND FIRE DETECTION SYSTEM

DSR E&M- SOR Amount NON-SOR TOTAL Amount

DSR E&M- SOR Amount NON-SOR TOTAL Amount

S.No. Description Unit Qty. SOR Rate (Rs.) Market Rate

2025/ NS (Rs.) Amount (Rs.) (Rs.)

Internal Piping

1 DSR-25 Providing, laying, testing & commissioning of ’C’ class heavy

27.7 duty MS pipe conforming to IS 3589/IS 1239 including Welding,

fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc.

and fixing the pipe on the wall/ceiling with suitable

clamp/support frame and painting with two or more coats of

synthetic enamel paint of required shade complete as required :

2 DSR-25 (A) Supplying, installation, testing and commissioning of electric

27.4 driven terrace pump suitable for automatic operation and

consisting of following, complete in all respects, as required:

(B) Horizontal type, multistage, centrifugal, split casing pump of

cast iron body & bronze impeller with stainless steel shaft,

mechanical confirming to IS : 1520

(C) Suitable HP squirell cage induction motor TEFC type suitable

for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55

class of protection for enclosure, horiziontal foot mounted

type with Class-’F’ insulation, conforming to IS-325.

(D) M.S. fabricated common base plate, coupling, coupling

guard, foundation bolts etc. as required.

(E) Suitable cement concrete foundation duly plastered and with

anti vibration pads.

3 MR Fire pump control panel (DOL/Star-Delta Starter) for 7.5 HP, 900

LPM Fire pmp, Atomatic/Manal, IS:13947, NFPA 20, IEC 60947,

UL 508, Power supply 415 AC, 3-Phase, 50Hz.

4 DSR-25 Supplying, fixing, testing and commissioning of butterfly valve of

27.11 PN 1.6 rating with bronze/gunmetal seat duly ISI marked

complete with nuts, bolts, washers, gaskets conforming to IS

13095 of following sizes as required :

Supplying & Fixing of Gunmetal Bourdon Type pressure gauge

with gunmetal isolation ball valve tapping and connecting pipe

and nipple for pump sets, complete in all respects, as per

Technical Specifications and Drawings, suitable for working

pressure of 250 PSI. Cost shall be inclusive of providing any

short pieces, nipples, elbows etc as required.

Providing, installation, testing and commissioning of non-return

valve of following sizes confirming to IS: 5312 complete with

rubber gasket, GI bolts, nuts, washers etc.as required :

6 DSR-25 Supplying and fixing orifice plate made out of 6 mm thick ₹ 1,436.00 ₹ 28,720.00

27.13 stainless steel (Grade304) with orifice of required size to be

fitted between flange & landing valve of external and internal

hydrants to reduce pressure at the outlet to the level of 3.5

kg/cm2 complete as required. Set 20 ₹ 28,720.00

7 DSR-25 Providing, installation, testing and commissioning of stainless

27.15 steel Y-strainer fabricated out of 1.6 mm thick stainless steel,

Grade 304, sheet with 3 mm dia holes with stainless steel

8 DSR-25 Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with

27.16 63 mm dia male and female couplings duly bound with GI wire,

rivets etc. conforming to IS 636 (type-A) as required :

9 DSR-25 Supplying & fixing 63 mm dia gun metal short branch pipe with

27.18 20mm nominal internal diameter size nozzle conforming to IS

903 suitable for instantaneous connection to interconnect hose

Internal Hydrant

Digitally signed by 1 of 2

DSR E&M- SOR Amount NON-SOR TOTAL Amount

DSR E&M- SOR Amount NON-SOR TOTAL Amount

S.No. Description Unit Qty. SOR Rate (Rs.) Market Rate

2025/ NS (Rs.) Amount (Rs.) (Rs.)

10 DSR-25 Supplying and fixing single headed internal hydrant valve with

27.9 instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia

with cast iron wheel ISI marked conforming to IS 5290

(Type -A) with blank Gunmetal/Stainless Steel cap and chain as

27.9.2 Single headed Stainless Steel Set 20 ₹ 6,632.00 ₹ 1,32,640.00 ₹ 1,32,640.00

11 MR Supplying & installation of approved 1.6mm thick M.S. fire hose

cabinet (750x600x250mm) made ot of 16 gauge M.S. sheet

capable of accomodating two sets of RRL hose pipes, fittings &

accessories. The box shall have a front glass door with lock and

key arrangement & shall be painted with post office red color

Sprinkler System

12 DSR-25 Providing, fixing, testing & commissioning of 15mm dia

27.21 quartzoid bulb type sprinklers of rating 68 degree centigrade

with required accessories :

Fire Detection and Alarm System

13 Supplying, installation, testing and commissioning of micro

processor based intelligent addressable main fire alarm panel,

central processing unit with the following loop modules and

capable of supporting not less than 240 devices (including

detectors) and minimum 120 detectors per loop and loop length

up to 2 km, network communication card, minimum 320

character graphics/ LCD display with touch screen or other

keypad and minimum 4000 events history log in the non volatile

DSR-25 memory (EPROM), power supply unit (230 ± 5 % V, 50 hz), 48

28.2.1 hrs back-up with 24 volt sealed maintenance free batteries with

automatic charger.

The panel shall have facility to connect printer to printout log

and facility to have seamless integration with analog/digital

voice evacuation system (which is part of the schedule of work

under SH: PA System) and shall be complete with all accessories

. The panel shall be compatible for IBMS system with open

protocol BACnet/ Modbus over IP complete as per

specifications.

14 Supplying, installation, testing and commissioning of Smoke ₹ 92,948.00

detector and mounting base with LED light complete as

15 DSR-25 Supplying, installation, testing & commissioning of intelligent ₹ 66,888.00

28.2.6 addressable programmable sounder complete as required.

16 DSR-25 Supplying, installation, testing & commissioning of addressable ₹ 97,512.00

28.2.14 manual call point complete as required. Each 24 ₹ 4,063.00 ₹ 97,512.00

17 DSR-25 Supplying, installation, testing and commissioning of response ₹ 7,344.00

28.2.5 indicator on surface/recessed MS box having two LED , metallic

cover complete with all connections etc as required.

18 DSR-25 Supplying and laying of 2x1.5 sqmm fire survival armoured ₹ 5,21,100.00

28.5.1 cable, 600/1000V rated with annealed copper conductor having

glass mica fire barrier tape covered by an extruded layer of cross

linkable ethylene propylene rubber (EPR) insulation and LSZH

inner bedding, steel wire armouring & LSZH outer sheath

complete as required. metre 1350 ₹ 386.00 ₹ 5,21,100.00

Fire Extinguishers

19 MR Providing of ABC powder type( stored pressure) Fire

Extinguisher 4 KG. Capacity,ISI marked, IS 15683 for class 4 A

&89 B type of fire field with MAP -90 complete in all

20 MR Providing of CO2 type( stored pressure) Fire Extinguisher

4.5 KG. Capacity,ISI marked, IS 15222 with all accessories

complete in all respect.(Manual) Set 10 ₹ 4,500.00 ₹ 45,000.00 ₹ 45,000.00

21 MR Supplying & Fixing, Fire Buckets 9 litres capacity round bottom

sand buckets along with bucket stand (Wall hanging type) as

per local fire officer's standards and located at ground floor.

Emergency Lights

22 MR Supply, installation, testing and commissioning of LED

emergency light fitting, 6–10W, minimum 2 hours backup, with

lithium-ion/SMF battery, automatic operation on mains failure,

complete with driver, housing, wiring, mounting accessories,

and all necessary connections as per site requirement.

TOTAL FOR SOR-ITEMS ₹ 18,83,166.00

TOTAL FOR NON SOR-ITEMS ₹ 3,87,972.00

GRAND TOTAL ₹ 22,71,138.00

GRAND TOTAL ₹ 22,71,138.00

Digitally signed by 2 of 2

KV BARKATHA | SIGNAGE BOQ

Item Zone Item specification — supply and installation complete Size / extent Unit Quantity Rate (₹) Amount (₹)

Representative visual — concept only

S01 Outdoor Illuminated main school identity. Providing, fabricating, supplying

and fixing school entrance identity sign comprising 4 mm exterior

ACP fascia with 0.30 mm minimum aluminium skins on 40×40×2

mm MS box frame, zinc-rich primer and two coats exterior PU

paint, routed bilingual lettering and approved KVS emblem backed

with 3 mm opal acrylic, low-voltage LED modules, IP67 drivers in 3600 × 900 mm each 1 34,675.42 34,675.42

accessible enclosure, sealed joints, SS anchors, internal wiring and

testing; mounted to existing sound entrance wall, complete. No

new masonry included. Electrical supply point measured separately

S02 Outdoor Secondary gate identity. Providing and fixing non-illuminated gate

identification board of 3 mm exterior-grade aluminium composite

panel with aluminium skins minimum 0.25 mm, exterior printed

polymeric vinyl and UV-resistant matt overlaminate, sealed edges,

rounded corners, stainless steel screws and concealed fixings, on

25×25×1.6 mm painted MS frame including SS wall anchors, 1800 × 600 mm each 2 4,454.35 8,908.71

complete; existing wall mounting.

S03 Outdoor Campus orientation map. Providing and fixing campus map of 3

mm exterior-grade aluminium composite panel with aluminium

skins minimum 0.25 mm, exterior printed polymeric vinyl and UV-

resistant matt overlaminate, sealed edges, rounded corners,

stainless steel screws and concealed fixings, with YOU ARE

HERE, north arrow, pedestrian and accessible routes, approved 1200 × 900 mm each 1 5,482.28 5,482.28

building labels and legend, on 25×25×1.6 mm painted MS frame

including wall fixings, complete. Graphic preparation from

approved plan included.

S04 Outdoor Pedestrian direction sign on post. Providing and fixing single-face

directional board of 3 mm exterior-grade aluminium composite

panel with aluminium skins minimum 0.25 mm, exterior printed

polymeric vinyl and UV-resistant matt overlaminate, sealed edges,

rounded corners, stainless steel screws and concealed fixings,

fixed to one 60×60×3 mm painted MS post, board top about 2100 900 × 450 mm; one face each 6 6,852.85 41,117.10

mm above finished ground, with 250×250×10 mm base plate, four

M16 anchors, 450×450×600 mm M20 concrete footing over 75 mm

lean concrete, excavation, backfill and making good, complete.

Member sizes are budget basis; submit wind/stability design before

S05 Outdoor Parking and traffic control on post. Providing and fixing

traffic/parking board comprising 2 mm aluminium sheet with

engineering-grade retroreflective film, approved pictograms and

bilingual legend, 50×50×3 mm painted MS post, top about 2100

mm, 200×200×10 mm base plate, M12 anchors, 400×400×600 mm

M20 footing over 75 mm lean concrete, excavation and backfill 600 × 450 mm; one face each 8 4,111.71 32,893.68

complete; submit stability details.

S06 Outdoor Assembly point sign on post. Providing and fixing green assembly-

point board of 3 mm exterior-grade aluminium composite panel

with aluminium skins minimum 0.25 mm, exterior printed polymeric

vinyl and UV-resistant matt overlaminate, sealed edges, rounded

corners, stainless steel screws and concealed fixings, with

pictogram on 50×50×3 mm painted MS post, top about 2100 mm, 600 × 600 mm each 2 4,797.00 9,593.99

200×200×10 mm base plate, M12 anchors and 400×400×600 mm

M20 concrete footing over 75 mm lean concrete including

excavation and backfill, complete; coordinate safe location with fire

evacuation plan.

S07 Outdoor Sports area identity and rules. Providing and fixing wall/fence

mounted sports identity and concise safety-rules board of 3 mm

exterior-grade aluminium composite panel with aluminium skins

minimum 0.25 mm, exterior printed polymeric vinyl and UV-

resistant matt overlaminate, sealed edges, rounded corners,

stainless steel screws and concealed fixings, on 25×25×1.6 mm 900 × 600 mm each 7 3,769.07 26,383.47

painted MS frame, with SS clamps/anchors, complete.

S08 Outdoor Garden and activity area identity. Providing and fixing wall/low-

fence mounted area identity sign of 3 mm exterior-grade

aluminium composite panel with aluminium skins minimum 0.25

mm, exterior printed polymeric vinyl and UV-resistant matt

overlaminate, sealed edges, rounded corners, stainless steel

screws and concealed fixings, with concealed SS fixings or clamps 600 × 300 mm each 6 1,439.10 8,634.59

to existing support, complete.

S09 Outdoor Service and hazard board. Providing and fixing safety/service

identification sign of 3 mm exterior-grade aluminium composite

panel with aluminium skins minimum 0.25 mm, exterior printed

polymeric vinyl and UV-resistant matt overlaminate, sealed edges,

rounded corners, stainless steel screws and concealed fixings,

approved warning colours and pictograms, SS screws or fence 450 × 300 mm each 6 1,014.22 6,085.33

clamps, complete; wording and voltage on electrical signs

approved by electrical consultant.

Digitally signed by PRIYA

S10 Outdoor Residential block identity. Providing and fixing residential block

identity board of 3 mm exterior-grade aluminium composite panel

with aluminium skins minimum 0.25 mm, exterior printed polymeric

vinyl and UV-resistant matt overlaminate, sealed edges, rounded

corners, stainless steel screws and concealed fixings, wall

mounted with SS screws and plugs, complete. 600 × 300 mm each 3 1,439.10 4,317.30

S11 Outdoor Residence number plate. Providing and fixing individual dwelling

number plate of 3 mm exterior-grade aluminium composite panel

with aluminium skins minimum 0.25 mm, exterior printed polymeric

vinyl and UV-resistant matt overlaminate, sealed edges, rounded

corners, stainless steel screws and concealed fixings, bilingual

number/identifier, SS screws and plugs, complete. 200 × 100 mm each 9 479.70 4,317.30

S12 Indoor Classroom and Balvatika door plate. Providing and fixing

classroom identification plate of 3 mm solid aluminium panel,

powder-coated finish, UV-printed high-contrast Hindi and English

lettering with matt protective clear coating, rounded corners and

concealed screw fixings, including approved room number and

class label, complete. 300 × 150 mm each 38 712.70 27,082.46

S13 Indoor Specialist and administration door plate. Providing and fixing

specialist/administration room identification plate of 3 mm solid

aluminium panel, powder-coated finish, UV-printed high-contrast

Hindi and English lettering with matt protective clear coating,

rounded corners and concealed screw fixings, complete.

S14 Indoor Service-room identification. Providing and fixing service-room

identification sign of 3 mm solid aluminium panel, powder-coated

finish, UV-printed high-contrast Hindi and English lettering with

matt protective clear coating, rounded corners and concealed

screw fixings, with appropriate hazard pictogram where needed,

S15 Indoor Toilet identification with pictogram. Providing and fixing toilet

identification plate of 3 mm solid aluminium panel, powder-coated

finish, UV-printed high-contrast Hindi and English lettering with

matt protective clear coating, rounded corners and concealed

screw fixings, clear male/female/child pictogram with bilingual text,

complete; no cubicle-door plates included. 200 × 200 mm each 32 644.17 20,613.37

S16 Indoor Accessible tactile and Braille identity. Providing and fixing tactile

accessibility sign on 2 mm powder-coated aluminium base with

raised pictogram and characters, Grade 1 Braille in approved

language, non-glare high-contrast finish, rounded edges and

concealed screws, complete; locate adjacent to latch side at

accessible reach height subject to consultant approval. Includes 300 × 200 mm each 14 1,576.16 22,066.18

bilingual printed text; specialist Braille proof required.

S17 Indoor Main school directory. Providing and fixing main directory sign of 3

mm solid aluminium panel, powder-coated finish, UV-printed high-

contrast Hindi and English lettering with matt protective clear

coating, rounded corners and concealed screw fixings, in

25×25×1.6 mm painted MS backing frame, approved floorwise

room list, arrows and colour bands, complete. 900 × 1200 mm each 1 5,482.28 5,482.28

S18 Indoor Floor directory. Providing and fixing floorwise directory of 3 mm

solid aluminium panel, powder-coated finish, UV-printed high-

contrast Hindi and English lettering with matt protective clear

coating, rounded corners and concealed screw fixings, in

aluminium edge frame, with current floor marker, room list and

arrows, complete. 600 × 900 mm each 4 3,220.84 12,883.36

S19 Indoor Corridor directional panel. Providing and fixing single-face corridor

direction panel of 3 mm solid aluminium panel, powder-coated

finish, UV-printed high-contrast Hindi and English lettering with

matt protective clear coating, rounded corners and concealed

screw fixings, approved arrows and up to three destinations,

mounted flat to wall or beam without reducing headroom, 600 × 200 mm each 16 1,507.63 24,122.03

Digitally signed by PRIYA

S20 Indoor Stair and floor marker. Providing and fixing stair identification and

floor marker of 3 mm solid aluminium panel, powder-coated finish,

UV-printed high-contrast Hindi and English lettering with matt

protective clear coating, rounded corners and concealed screw

fixings, bilingual floor number and stair ID, complete.

S21 Indoor Drinking water identification. Providing and fixing drinking-water

sign of 3 mm solid aluminium panel, powder-coated finish, UV-

printed high-contrast Hindi and English lettering with matt

protective clear coating, rounded corners and concealed screw

fixings, including potable-water pictogram, complete.

S22 Indoor Lab and activity safety rules. Providing and fixing concise safety-

rule board of 3 mm solid aluminium panel, powder-coated finish,

UV-printed high-contrast Hindi and English lettering with matt

protective clear coating, rounded corners and concealed screw

fixings, with room-specific pictograms and bilingual instructions,

complete; text proofed by school/subject teacher. 450 × 600 mm each 8 1,850.27 14,802.16

S23 Indoor School conduct and safeguarding board. Providing and fixing

bilingual school conduct/information board of 3 mm solid

aluminium panel, powder-coated finish, UV-printed high-contrast

Hindi and English lettering with matt protective clear coating,

rounded corners and concealed screw fixings, max 150 words

equivalent including safety pictograms and approved school 600 × 900 mm each 4 3,015.25 12,061.02

contact fields, complete; excludes general display/notice boards.

S24 Indoor Evacuation plan board. Providing and fixing location-specific

evacuation plan printed on photoluminescent film bonded to 2 mm

aluminium sheet, matt finish, showing YOU ARE HERE, correct

orientation, escape route, stairs, fire equipment and assembly

point, including graphic preparation and SS fixings complete;

prepare from approved fire plan and validate every location. 450 × 600 mm each 8 2,192.91 17,543.30

S25 Indoor Photoluminescent exit-direction sign. Providing and fixing

photoluminescent escape-direction sign on 1.5 mm aluminium

backing with green/white running-man pictogram, arrow and

bilingual legend, complete with SS screws; submit glow

performance test certificate suitable for approved fire strategy.

These supplement electrically illuminated exit signs. 300 × 150 mm each 24 507.11 12,170.66

S26 Indoor Battery-backed LED exit sign. Supplying, installing, testing and

commissioning maintained LED EXIT sign, double-face display

where required, rigid aluminium housing with green/white

pictogram and bilingual legend, minimum 90-minute rechargeable

battery backup, automatic changeover, charge indicator, test

switch, wall/ceiling brackets and internal wiring complete; electrical 300 × 150 mm nominal each 16 2,261.44 36,183.05

supply point measured under S31. Confirm required autonomy with

fire consultant.

S27 Indoor Fire equipment identification. Providing and fixing

photoluminescent fire-equipment identification sign on 1.5 mm

aluminium backing with red/white pictogram and bilingual text,

complete with SS screws, coordinated to actual installed

equipment; equipment itself excluded.

S28 Indoor Fire action instruction board. Providing and fixing fire-action

instruction board on 1.5 mm aluminium backing with

photoluminescent printed face, pictograms, approved bilingual

instructions, alarm/office contact fields and SS fixings complete.

S29 Indoor Lift safety and restricted access. Providing and fixing

caution/restricted-access plate of 3 mm solid aluminium panel,

powder-coated finish, UV-printed high-contrast Hindi and English

lettering with matt protective clear coating, rounded corners and

concealed screw fixings, approved pictogram and bilingual text,

Digitally signed by PRIYA

S30 Indoor Glazed-door visibility manifestation. Providing and applying

durable opaque frosted/coloured safety manifestation film in two

continuous 50 mm wide bands on clear glass at architect-approved

visible heights, including cleaning, cutting, alignment and finishing

complete. Measured as actual running length of film per band;

glass and door signs excluded. 50 mm wide; two bands m 40 109.65 4,385.82

S31 Electrical Electrical supply point for illuminated signs. Providing and

connecting dedicated sign supply point from existing nearby

protected lighting circuit, with 2×1.5 sq.mm copper FRLS

conductors plus 1×1.5 sq.mm earth in 20 mm conduit for route up

to 10 m each, local isolating switch, weatherproof junction box

where outdoors, termination, earthing continuity, testing and One point; maximum 10 m

making good, complete; no new DB, long feeder, trench or meter route

included. Gate sign final circuit and protection to be checked by

electrical consultant.

TOTAL BUDGET 4,91,349.35

Digitally signed by PRIYA

PROPOSED CONSTRUCTION OF STAFF QUARTER TYPE-III (G+1)

ABSTRACT OF COST - CIVIL WORKS

SOR-2023 NON SOR

Sl. No. SOR-2022 DESCRIPTION

A 2 EARTH WORKS 2,49,750.65 -

B 4 CONCRETE WORKS 2,48,066.58 -

C 5 REINFORCED CEMENT CONCRETE WORK 51,34,899.81 -

D 6 BRICK WORK 12,44,991.32 -

E 8 MARBLE & GRANITE WORK 3,54,242.94 -

G 10 STEEL WORK 3,20,852.74 -

H 11 FLOORING WORK 7,78,277.33 -

J 13 FINISHING WORK 14,09,656.84 -

K 21 ALUMINIUM WORK 3,784.18 -

L 22 WATER PROOFING 1,45,156.24 -

GRAND TOTAL 1,13,83,668

GRAND TOTAL 1,13,83,668

Digitally signed by PRIYA

BILL OF QUANTITYFOR STAFF QUARTER TYPE-III (G+1)

Sl. No. DSR-2023 DESCRIPTION UNIT QTY. RATE DSR AMT. NSOR AMT.

A 2.00 EARTH WORKS

1 2.6 Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas

(exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and

disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-

i 2.6.1 All kinds of soils Cum 271.38 177.50 48,169.42

2 2.7 Earth work in excavation by mechanical means (Hydralic excavator/manual means)over areas

(exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including getting out and

disposal of excavated earth, lead upto 50m and lift upto 1.5m, as directed by Engineer - in

3 2.10 Excavating trenches of required width for pipes, cables, etc. including excavation for sockets,

and dressing of sides, ramming of bottoms, depth upto 1.5m including getting out the excavated

soil, and then returning the soil as required, in layers not exc

a 2.10.1 All kinds of soil.

i 2.10.1.2 Pipes, cables, etc. exceeding 80mm dia but not exceeding 300mm dia. Metre 20.00 352.15 7,043.00

4 2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in

layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and

watering, lead up to 50 m and lift upto 1.5 m.

5 2.26. Extra for every additional lift of 1.5 m or part thereof in excavation /

banking excavated or stacked materials.

5.2 2.26.2 Ordinary or hard rock Cum 6.00 227.40 1,364.40

6 2.27 Supplying and filling in plinth with sand under floors, including watering,

ramming, consolidating and dressing complete. Cum 28.57 2123.75 60,665.13

7 2.28 Surface dressing of the ground including removing vegetation and inequalities not exceeding 15

cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.

i 2.28.1 All kinds of soil Sqm 385.00 34.15 13,147.75

8 2.34 Supplying chemical emulsion in sealed containers including delivery as specified

i 2.34.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% Litre 54.42 234.75 12,775.10

9 2.35 Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment

(excluding the cost of chemical emulsion) :

i 2.35.1.1 Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres / sqm

of the vertical surface of the substructure to a depth of 300mm including excavation channel

along the wall & rodding etc. complete: With Chlorpyriphos/ Lindane E.C. 20% with 1%

a) 2.35.3 Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm

apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2

Coarse sand) to match the existing floor:

i 2.35.3.1 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration Sqm 145.12 310.05 44,994.46

TOTAL (Carried Over to Summary of Civil Works) 2,49,750.65 0.00

B 4.00 CONCRETE WORKS

1 4.1 Providing and laying in position cement concrete of specified grade excluding the cost of

centering and shuttering - All work up to plinth level :

a 4.1.6 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone

aggregate 40 mm nominal size derived from natural sources) Cum 14.73 7178.75 1,05,760.22

b 4.1.8 1 :4:8 (1 Cement : 4 coarse sand (zone-Ill) derived from

natural sources : 8 graded stone aggregate 40 mm nominal

size derived from natural sources) Cum 12.35 6812.00 84,127.35

2 4.3 Centering and shuttering including strutting, propping etc. and removal of form work for :

i 4.3.1 Foundations, footings, bases for columns. Sqm 15.36 392.15 6,023.42

3 4.11 Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2

coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20mm nominal

size derived from natural sources).

4 4.12 Extra for providing and mixing water proofing material in cement concrete work in doses by

weight of cement as per manufacturer's specification. Per 50 kg

5 4.13 Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality

using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and

finally with a piece of cloth lightly soaked in kerosene oil. Sqm 22.22 146.15 3,247.64

Digitally signed by PRIYA

Sl. No. DSR-2023 DESCRIPTION UNIT QTY. RATE DSR AMT. NSOR AMT.

6 4.17 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone -

III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40

mm nominal size, well rammed and consolidated and grouted with fine sand, including

necessary excavation, levelling & dressing & finishing the top smooth.

TOTAL (Carried Over to Summary of Civil Works) 2,48,066.58 0.00

C 5.00 REINFORCED CEMENT CONCRETE WORK

1 5.9 Centering and shuttering including strutting, propping etc. and removal of form for :

a 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete. Sqm 136.48 392.15 53,520.63

b 5.9.2 Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

c 5.9.3 Suspended floors, roofs, landings, balconies and access platform. Sqm 383.95 927.25 3,56,015.32

d 5.9.4 Shelves (Cast in situ) Sqm 36.98 927.25 34,285.07

e 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers Sqm 481.39 736.40 3,54,492.94

f 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts. Sqm 207.06 961.30 1,99,046.78

g 5.9.7 Stairs, (excluding landings) except spiral-staircases. Sqm 42.71 764.95 32,667.19

i 5.9.16 Edges of slabs and breaks in floors and walls

j 5.9.19 Weather shade, Chajjas, corbels etc., including edges. Sqm 15.12 951.10 14,380.63

2 5.22 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position

and binding all complete upto plinth level.

i 5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. Kg 5923.70 107.85 6,38,871.05

3 5.22A Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position

and binding all complete above plinth level.

i 5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. Kg 15697.39 107.85 16,92,963.81

4 5.33.1 Providing and laying in position ready mixed or site batched design mix cement concrete for

reinforced cement concrete work; using coarse aggregate and fine aggregate derived from

natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in

recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve

durability and workability without impairing strength; including pumping of concrete to site of

laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and

reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be

payable separately. In case the cement content in design mix is more than 110% of the specified

minimum cement content, the contractor shall have discretion to either re-design the mix or bear

the cost of extra cement.

a) 5.33.1 All works upto plinth level.

i 5.33.1.1 Concrete of M25 grade with minimum cement content of 330 kg /cum Cum 55.07 9504.75 5,23,437.28

b) 5.33.2 All works above plinth level upto floor V level.

i 5.33.2.1 Concrete of M25 grade with minimum cement content of 330 kg /cum Cum 119.08 9860.40 11,74,130.70

5 5.30 Add for plaster drip course/ groove in plastered surface or moulding to

R.C.C. projections. metre 330.70 78.40 25,926.88

TOTAL (Carried Over to Summary of Civil Works) 51,34,899.81 0.00

D 6.00 BRICK WORK

1 6.1 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in

foundation and plinth in:

i 6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 14.22 7132.25 1,01,436.64

2 6.32 Brick work with clay flyash F.P.S. (non modular) brick of class designation

7.5 in superstructure above plinth level up to floor five level in :

i 6.32.2 Cement mortar 1 :6 (1 cement : 6 coarse sand) Cum 100.37 9095.05 9,12,826.06

3 6.13 Half brick masonry with common burnt clay F.P.S. (non modular) bricks

of class designation 7.5 in superstructure above plinth level up to floor

3.1 6.13.2 Cement mortar 1 :4 (1 cement :4 coarse sand) Sqm 187.80 1123.80 2,11,047.39

4 6.15 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half

brick masonry. Sqm 187.80 104.80 19,681.23

TOTAL (Carried Over to Summary of Civil Works) 12,44,991.32 0.00

E 8.00 MARBLE & GRANITE WORK

1 8.2 Providing and fixing 18mm thick gang saw cut ( premoulded and prepolished) machine cut for

kitchen platforms, vanity counters, window sills , facias and similar locations of required size of

approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4

coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch

ups, including rubbing, curing, moulding and polishing to edge to give high gloss finish etc.

complete at all levels.

b) 8.2.2 Granite of any colour and shade

Digitally signed by PRIYA

Sl. No. DSR-2023 DESCRIPTION UNIT QTY. RATE DSR AMT. NSOR AMT.

2 8.3.2 Providing edge moulding to 18 mm thick marble stone counters, Vanities

etc., including machine polishing to edge to give high gloss finish etc.

complete as per design approved by Engineer-in-Charge. (Granite work) metre 23.40 510.95 11,956.23

3 8.4 Extra for fixing marble /granite stone, over and above corresponding

basic item, in facia and drops of width upto 150 mm with epoxy resin

based adhesive, including cleaning etc. complete. metre 23.40 568.55 13,304.07

1 8.5 Extra for providing opening of required size & shape for wash basin/

kitchen sink in kitchen platform, vanity counter and similar location in

marble/ Granite/ stone work, including necessary holes for pillar taps etc.

including moulding, rubbing and polishing of cut edges etc. complete. Each 4.00 978.70 3,914.80

4 8.31 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be

specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle

green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and

dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with

grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of

matching shade complete.

TOTAL (Carried Over to Summary of Civil Works) 3,54,242.94 0.00

F 9.00 WOOD, WPC & uPVC WORK

1 9.21.1 Providing and fixing ISi marked flush door shutters conforming to IS :

2202 (Part I) non-decorative type, core of block board construction

with frame of 1st class hard wood and well matched commercial 3 ply

veneering with vertical grains or cross bands and face veneers on both

faces of shutters: (35 mm thick including ISi marked Stainless Steel butt hingesn with necessary

2 9.127.2 Providing & Fixing decorative high pressure laminated sheet of plain

I wood grain in gloss / matt/ suede finish with high density protective

surface layer and reverse side of adhesive bonding quality conforming to

IS : 2046 Type S, including cost of adhesive of approved quality. (1.0 mm thick) Sqm 58.22 897.30 52,240.81

3 9.23 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges

of flush door shutters (over all area of door shutter to be measured).

4 9.24.1 Extra for providing vision panel not exceeding 0.1 sqm in all type of

flush doors (cost of glass excluded) (overall area of door shutter to be

measured): Rectangular or square

5 9.26 Extra for cutting rebate in flush door shutters (Total area of the shutter to

be measured). Sqm 10.66 106.70 1,137.42

6 9.70.2 Providing and fixing IS : 12817 marked stainless steel butt hinges with

stainless steel screws etc. complete : 100X58X1.90 mm

7 26.86 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid

door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of

K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice

husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated

with miter joints after applying PVC solvent cement and screwed with full body threaded star

headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of

2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of

elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of

being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S

hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of

Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately).Note:

For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of

profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but

no extra payment on this account shall be made.

8 26.87 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain

flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension

Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic

additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum

and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive

strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class

A category with property of being termite/ borer proof, water/moisture proof and fire retardant

and fixing with stainless steel butt hinges of required size with necessary full body threaded star

headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless

steel butt hinges and necessary S.S screws shall be paid separately)

9 9.46.2 Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25mm with two

chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever

necessary complete : 20 mm dia Rmt 63.54 393.25 24,987.11

10 9.48.2 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats,

square or round bars etc. including priming coat with approved steel primer all complete.Fixed to

openings /wooden frames with rawl plugs screws etc. Kg 412.99 238.35 98,436.64

Digitally signed by PRIYA

Sl. No. DSR-2023 DESCRIPTION UNIT QTY. RATE DSR AMT. NSOR AMT.

11 9.96.2 Providing and fixing aluminium sliding door bolts, ISi marked anodised

(anodic coating not less than grade AC 10 as per IS : 1868), transparent

or dyed to required colour or shade, with nuts and screws etc. complete : (250x16 mm)

12 9.97 Providing and fixing aluminium tower bolts, ISi marked, anodised (anodic

coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed

to required colour or shade, with necessary screws etc. complete :

13 9.103 Providing and fixing bright finished brass 100 mm mortice latch and lock,

ISi marked, with six levers and a pair of anodised (anodic coating not less

than grade AC 10 as per IS : 1868) aluminium lever handles of approved

quality with necessary screws etc. complete. Each 4.00 868.95 3,475.80

14 9.82 Providing and fixing bright finished brass hanging type floor door stopper