GE/SRA/T-34 OF 2019-2020

Amount

Demolition Cement Concrete (un-reinforced) of any description in Ground Floors, Pavings, etc. not exc. 150mm thickness (above or below Ground Level) and removing debris, etc. to Outside MD/AF Land, complete all as specified and as directed.

Demolition Cement Concrete (Reinforced) of Roofs, Floors (other than Ground Floors), Beams,Staircases,Landings,Chajjas and Similar Suspended Work (Reinforcement cut as required to facilitate demolition),and removing debris, etc. to Outside MD/AF Land, complete all as specified and as directed.

Demolition Brick work built in Cement Mortar and in any Position including all Quoins, Arches and Pillars, etc., complete all as specified and as directed.

Taking down Chowkat or Frame of any description (without taking off Shutter from the Frame) not exc. 1.50 Square Metre Each, complete all as specified and as directed.

Taking down Shutter of any description, exc. 1.00 Square Metre but not exc. 2.00 Square Metre Each, complete all as specified and as directed.

Taking down Steel Window with Frame(complete), area not exc. 1.5 Square Meter Each,complete all as specified and as directed.

Dismantling Stone Slabs and/or Tiles of any description or thickness in Floors, Aprons, etc. laid, bedded and pointed in Cement Mortar and removing debris, etc. to Outside MD/AF Land, complete all as specified and as directed.

Dismantling Pre-Cast Concrete Blocks of any description or thickness in Floors, Aprons,etc and removing debris, etc to Outside MD/AF Land, Complete all as specified as directed

Dismantling damaged/unserviceable Plain/ Corrugated steel sheeting of any gauge and thickness, of any descriptions, complete all as specified and as as directed.

Dismantling Structural Steel or Mild Steel Work of any description not otherwise provided for, complete all as specified and as directed.

Taking down Cement Plaster including raking out Joints, hacking for Key, scrubbing down with Water and removing Debris, etc. to Outside MD/AF Land, complete all as specified and as directed.

Hacking out old broken Glass (any thickness, size, quality or description) from Metal Frame including punching or drilling out old Glazing Pins/Spring Clips or fixed with Beads, complete all as specified and as directed.

M&L Reinforced Cement Concrete 1:1½:3 (20mm gradded stone aggregate) in Chajjas and similar items., etc., complete all as specified and as directed. NOTE : Reinforcement will be Measured and Paid for separately under appropriate Item.

M&L Coarse Aggregate 40mm graded, spread around Sub-station, Poles, or any other loactions in required thickness, area on levelled, complete all as specified and as directed.

M&L Brick Work with Sub-Class ‘B’ Bricks (Old Size Bricks), Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:4, complete all as specified and as directed.

M&L Brick work with Sub-Class ‘B’ Bricks but except Bricks (Serviceable Bricks obtained from Item No. 3 here-in-before) including removing old Mortar, Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:4, complete all as specified and as directed.

M&L Cutting Holes in Brick Walls, exc. Half Brick but not exc. One Brick thick, built in Cement Mortar for inserting of Cooler Stand, Lugs and Making Good to dismantled portion with Cement Concrete 1:2:4 (20mm graded stone aggregate) or Cement Mortar 1:3 (as required) and adjoining Surfaces in Cement Mortar 1:4, complete all as specified and as directed.

M&L Formwork to Chullah Hoods, Chajja, throughs and Similar Items including Edges for Rough Finished Flat Surfaces of Concrete, complete all as specified and as directed.

M&L Second Class Hardwood Plain Framed Panelled Shutter 35mm thick (any number of Panels) with Panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: and fitted to Steel Frame, complete all as specified and as directed.

S&F Solid PVC Door Frame of Wood grain of size 50x47mm made out of 5.0mm Plain Colour (Ivory shade) PVC Sheet Reinforced with Mild Steel Square Tube and fixing in Opening, complete all as specified and as directed.

S&F Factory Made Solid Panel PVC Door Shutter 30mm thick (Style) Plain Colour (Ivory Shade) consisting of Frame made out of Mild Steel Tubes for Top & Bottom Rails of Mild Steel Frame shall be covered with Heat Moulded Wood Grain PVC ‘C’ Channel having a PVC Sheet Strip of 20mm width Stuck inside with Solvent Cement for Stiles and Wood Grain PVC Sheets for Top Rail Lock Rail & Bottom Rail on either side and as gap insert for Top Rail & Bottom Rail, Panelling of Wood Grain PVC Sheet to be fitted in the Mild Steel Frame welded/sealed to the Stiles & Rails with suitable 5.0mm thick x 15mm wide PVC Sheet Beading used inside Stiles and Rails and decorative PVC Beading of 10mmx10mm (90°) and jointed together with Solvent Cement and fixing in the Frame at Site, complete all as specified and as directed. NOTE: Stainless Steel Hinges will be measured and paid under appropriate Items

M&L Steel Window Box type using ERW ‘P’ Section comprising Double Frame for Gauged and Glazed Skeleton Shutter jointed internally with Flat Iron 40x3mm complete including Mild Steel Tower Bolts, Hinges, Handle, Stops, Lugs including GI Steel Wire Cloth, Glazing, etc. all as directed. Outer Section of Frame should be 50x25mm and Inner Section should be 40x20mm, complete all as specified and as directed. NOTE :- (a) For the purpose of Measurement & Payment Double Shutter with Frame shall be considered as One Unit. (b) Cost of Iron Mongery as ordered/required at Site, GI Steel Wire Cloth will deem to be included in the Quoted Unit Rate. (c) Guard Bars are included in the Quoted Unit Rate. Spacing of 10mm Square Bar will be 10 Cm Centre to Centre. (d) Glazing shall be Measured and Paid separately under appropriate Item. MAKE : RAM FABRICATORS PVT LTD, PANCHKULA/ GANPATI DOORS, RAJPURA/ FRIENDS MANUFACTURING COMPANY, KOTKPURA (PUNJAB)

S&F Aluminium Barrel Tower Bolt 100mm long , Extruded Section, complete all as specified and as directed.

S&F Aluminium Barrel Tower Bolt 150mm long , Extruded Section, complete all as specified and as directed.

S&F Aluminium alloy, anodized,Sliding Door Bolts having length of Bolt 250mm long with Hasph Stable (Bolt type) and Fixing Clips of sheet cast or extruded section and fixing Bolts and sliding Bolts of extruded section and fixing,complete all as specified and as directed.

S&F Stainless Steel Butt Hinge 75mm long (weight not less than 60 Gram) and fixed, complete all as specified and as directed.

S&F Stainless Steel Butt Hinge of size 100mm (weight not less than 80 Gram), complete all as specified and as directed.

S&F Extruded Aluminium alloy Handle 125mm long, Fabricated type, anodised, complete all as specified and as directed.

S&F Extruded Aluminium alloy Handle 150mm long (weight not less than 120 Gram), Fabricated type, anodised, complete all as specified and as directed.

S&F Mild Steel 150mm, Ordinary Rat Tail Rod pattern Springs including Roller and Roller Plate and fixed, complete all as specified and as directed.

S&F Sheet Glass 4.0mm thick, Ordinary quality and glazing with Oil Putty in Square not exc. 0.50 Square Metre in Each Pane, complete all as specified and as directed.

M&L TMT Bars 10mm dia and over cut to length bent to shape required, including cranking, bending spirally for hooping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia or securing with Clips, complete all as specified and as directed.

M&L TMT Bars 8.0mm dia, cut to length bent to shape required including cranking, bending spirally for hoping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia or securing with Clips, complete all as specified and as directed.

S&F Steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS . S 1161-1979 grade St-240 complete all as specified and as directed.

Taking down existing Steel Rolling Shutter including Hood Cover, Pull and Push type, not exc. 8.00 Sqm area of Sides of clear opening and cleaning the Side of Shutters suspension Shafts, Anti-guide Channels and greasing to all the movable Parts of Rolling Shutter and straightening Rolling Shafts including replacement of Bolts, Nuts, etc. as reuired for smooth functioning of Shutter and re-fixing the same including Hood Cover, complete all as specified and as directed.

Taking down existing Steel Rolling Shutter including Hood Cover, Pull and Push type, not exc. 8.00 Sqm area of Sides of clear opening and repair/replacement of rolling shutter 1.25 thick steel sheeting and also providing with grilled rolling shutter at the height of 1.2 metre for sufficient ventilation including repair/replacement of side suspension of rolling shutter, cleaning the sides, Shafts, Anti-guide Channels and greasing to all the movable Parts of Rolling Shutter and straightening Rolling Shafts including replacement of Bolts, Nuts, etc. as reuired for smooth functioning of Shutter and re-fixing the same including Hood Cover, complete all as specified and as directed.

S&F 0.63 mm thick Galvanised, Corrugated mild steel sheeting with two corrugations side lap fixed with coach screw and washer in roof, walls etc. with grade of zinc coating 275, complete all as specified.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) 75mm thick in Sub-bases, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (12.5mm graded stone aggregate) 25mm thick in Sub-base for laying/fixing of Tiles in Floor, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (20mm graded stone aggregate) 100mm thick as in Path/ Hardstanding, laid in alternate Bay/Panel, finishing Cement Concrete surface Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L Machine Cut Kota Stone Slab 20-25mm thick in Flooring over and including Cement Screed 15mm thick in Cement Mortar 1:6, laid and jointed with Grey Cement Slurry mixed with Pigment to match the Shade of the Slab including Rubbing and Polishing, complete all as specified and as directed. NOTE : Cost of Screed Bed will deem to be included in the Quoted Unit Rate.

M&L Machine Cut Kota Stone Slab 20-25mm thick in Riser of Steps, Skirting, Dado and Pillar, laid over and including Cement Screed 10mm thick in Cement Mortar 1:4, laid and jointed with Grey Cement Slurry mixed with Pigment to match the Shade of the Slab including Rubbing and Polishing, complete all as specified and as directed. NOTE : Cost of Screed Bed will deem to be included in the Quoted Unit Rate.

M&L Machine Pressed Pre-cast Concrete Interlocking Polished Paver Block 60mm thick of M-35 Grade, with Grey Cement and Pigment of any shape and size (as ordered), conforming IS-15658-2006, ISI Marked, laid dry over Clean dry Sand and grouted with Clean dry Sand as in Floors, complete all as specified and as directed. NOTE : Clean dry Sand will be Measured and Paid separately under appropriate Item.

M&L Sand filling under Floor or in Fundation including watering and consolidation, complete all as specified and as directed.

M&L Rendering (Internal) 15mm thick in Cement Mortar 1:6 on Brick Walls or on Concrete Surfaces, Plastered Surfaces finished Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L Rendering 5.0mm thick in Cement Mortar 1:3 on Concrete Surfaces of Ceilings, Plastered Surfaces finished Fair and Even, complete all as specified and as directed.

M&L Rendering (External) 15mm thick in Cement Mortar 1:4 on Brick Walls or on Concrete Surfaces, mixing WPC as per manufacturers instructions, Plastered Surfaces finished Even and Smooth without using Extra Cement, complete all as specified and as directed. NOTE: WPC will be Measured and Paid under appropriate Item.

M&L Rough Cast Plaster on Brick Walls consisting Under Coat of Cement and Sand Mortar 1:3 not less than 10mm thick and while it is still in Plastic state the Rough Cast Mixture consisting of Crushed Stone or Fine Gravel mixed with Coarse Sand and Cement in the Ratio 1:1:1 shall be applied and finish Even, complete all as specified and as directed.

Supply only Integral Water Proofing Compound, ISI Marked, as approved, complete all as specified and as directed.

M&L preparing newly Plastered Surfaces of Ceiling and applying Three Coats of White Wash, complete all as specified and as directed.

M&L preparing old Plastered Surfaces of Ceiling and applying a Coat of White Wash, complete all as specified and as directed.

M&L preparing newly Plastered Surfaces of Walls by applying Wall Care Putty including Rubbing down with Sand Paper to obtain a Smooth Finish Surface and applying Two Coats of Distemper Oil Emulsion (as approved) over a Coat of Primer, complete all as specified and as directed.

M&L preparing old Decorated/Treated Plastered Surfaces of Walls and applying One Coat of Distemper Oil Emulsion (as approved), complete all as specified and as directed.

M&L preparing newly Plastered Surfaces of Walls by applying Wall Putty, cutting/rubbing to obtained a Smooth Surface and applying Two Coats of Weather Coat Exterior Paint (in Camuflage/Plain pattern as ordered) with approved Tint over a coat of Primer (as per Manu-facturer's instructions), complete all as specified and as directed.

M&L preparing newly Rough Cast Plastered Surfaces of Walls and applying Two Coats of Weather Coat Exterior Paint (in Camuflage/ Plain pattern as ordered) with approved Tint over a coat of Primer (as per Manufacturer's instructions), complete all as specified and as directed.

M&L preparing newly Plastered Surfaces of Walls and applying Two Coats of Weather Coat Exterior Paint (in Camouflaging/ Plain Pattern) with approved Tint as per manufacturer's instructions, complete all as specified and as directed.

M&L preparing old Decorated/Treated Plastered Surfaces of Walls and applying One Coat of Weather Coat Exterior Paint (in Camou-flaging/Plain Pattern) with approved Tint as per manufacturer's instructions, complete all as specified and as directed.

M&L preparing new previously untreated/Painted Wood and Wood Based Surfaces of any description, not otherwise described, over 10 Cm width or girth and applying two coats of Synthetic Enamel Paint (First quality) over a coat of pink primer, complete all as specified and as directed.

M&L preparing old Decorated/Painted Wood and Wood Based Surfaces of any description, not otherwise described, over 10 Cm width or girth and applying One Coat of Synthetic Enamel Paint (First quality), complete all as specified and as directed.

M&L preparing new or previously untreated Steel and Iron Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

M&L preparing old Decorated/Painted Steel and Iron Surfaces of any description, over 10 Cm width or girth and applying One Coat of Synthetic Enamel Paint (First quality), complete all as specified and as directed.

AGGARWAL CONSTRUCTION CO.

DCM ENTERPRISES

SHIVAM ENTERPRISES

ADITI FORMATION COMPANY

Sethi Builders

YESH BUILDERS