Fire Safety System

Name of Work :: Installation of Fire Safety System & Other Misc. Work at Mahudha ITI Building, Dist. Kheda.

Bill of Quantities (BOQ)

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[1] Fire Fighting Fire Pump Room & Accessories Supplying, Installation, 1.00 No 1,31,300.00

Testing and commissioning of Electric driven Main Fire Hydrant

pump suitable for automatic operation and consisting of following:

Horizontal type, centrifugal End Suction pump of cast iron body &

CI impeller , gland packing to ensure a minimum pressure of 3.5 kg

/ sq.cm. at highest and farthest outlet at specified flow of

LPM @ 60M. head with M.S.fabricated common base plate,

coupling, coupling guard, foundation bolts etc. as required

[2] Supplying, Installation, Testing and commissioning of Jockey Pump 1.00 No 54,338.00

10.8M3/hour @60M Head.Horizontal Centrifugal End Suction. with

M.S.fabricated common base plate, coupling, coupling guard,

foundation bolts etc. as required

[3] Supplying, Installation, Testing and commissioning of Diesel Engine 1.00 No 3,45,420.00

driven Main Fire Hydrant pump suitable for automatic operation

and consisting of following: Horizontal type, centrifugal End

Suction pump of cast iron body & CI impeller , gland packing to

ensure a minimum pressure of 3.5 kg / sq.cm. at highest and

farthest outlet at specified flow of 1120 LPM @ 60M. head with

M.S.fabricated common base plate, coupling, coupling guard,

foundation bolts etc. as required

[4] Supplying, Installing and fixing Diesel Engine (Pump) 130AH 24M 1.00 No 17,069.00

Genset Battery relevant to the required capacuty.

[5] Supplying, Installing and fixing of Diesel Engine (Pump) fuel Storage 1.00 No 19,392.00

tank No Diesel is in scope

[6] Supplying, Installing and fixing & Wrapping of Exhaust pipe with 3.00 Rmt 2,292.70

Insulation. it should be bigger then diesel discharge line. 80 MM

[7] Supplying, Installation, Testing and commissioning of cubical type 1.00 No 96,121.70

floor mounted power cum Fire Pump control panel complete with

suitable switch gear, bus bars, relays, contractors, indicating lamps,

fuses, instruments manual isolator & auxillary switch including

connections complete as required.(Contractor should submit GA

Drawing for approval before deliver the Panel at Site)

[8] Providing, fixing, testing and commissioning below Caballing work 15.00 Rmt 444.40

for Fire Pumps (Only from Panel to Pumps) 3 C X 35 Sqmm

Alluminium Armoured

[9] Providing, fixing, testing and commissioning below Caballing work 15.00 Rmt 303.00

for Fire Pumps (Only from Panel to Pumps) 3 C X 16 Sqmm

Alluminium Armoured

[10] Providing, fixing, testing and commissioning below Caballing work 30.00 Rmt 161.60

for Fire Pumps (Only from Panel to Pumps) 2 C X 1.5 Sqmm Copper

[11] Providing, fixing, testing and commissioning below Caballing work 5.00 Rmt 838.30

for Fire Pumps (Only from Panel to Pumps) Perforated G.I.sheet

cable tray Cable Tray .300X300X50mm .

[12] Providing, fixing, testing and commissioning below Caballing work 12.00 Rmt 606.00

for Fire Pumps (Only from Panel to Pumps) Perforated G.I.sheet

cable tray Cable Tray .150X150X50mm .

[13] Providing, fixing, testing and commissioningG.I. Earthing strips of 12.00 Rmt 919.10

50MM x 6MM thick, strip shall be run on floor / ceiling / walls,

from the equipment to the nearest Earth pit with neccessory

accessories as required. ( Earth pit shall be executed by other

[14] Cutting hole by Mechanical Means of upto 200 mm dia in 10.00 No 838.30

slab/beam throughout the thickness

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[15] Providing, fixing, testing & commissioning of Glicerin Filled dial 5.00 No 2,110.90

type Pressure Gauge and range of 0-15 Kg/cm2

[16] Providing, fixing, testing & commissioning of Pressure Switches for 3.00 No 3,040.10

automation of fire pumps. Pressure switches shall be double pole

single throw type suitable for 3 phase supply with diaphragm.

Aluminum Enclosure with IP 66 protection as required..

[17] Supplying, Installation, Testing and commissioning Sluice Gate 2.00 No 28,946.60

Valve - Cast Iron PN-1.6 (Flanged). Hand Wheel Operated to IS:

1538 with Fittings, Flanges, Nutbolts, Washers, Gaskets etc.of size:

150mm dia (For fire pump room & Accessories)

[18] Supplying, Installation, Testing and commissioning Sluice Gate 2.00 No 11,503.90

Valve - Cast Iron PN-1.6 (Flanged). Hand Wheel Operated to IS:

1538 with Fittings, Flanges, Nutbolts, Washers, Gaskets etc.of size:

80mm dia (For fire pump room & Accessories)

[19] Supplying, Installation, Testing and commissioning of C.I.Butterfly 1.00 No 8,726.40

valve conforming to I.S:13095 class PN 16 rating with Fittings,

Flanges, Nutbolts, Washers, Gaskets etc.of size: 150mm dia. (For

fire pump room & Accessories)

[20] Supplying, Installation, Testing and commissioning of C.I.Butterfly 4.00 No 5,029.80

valve conforming to I.S:13095 class PN 16 rating with Fittings,

Flanges, Nutbolts, Washers, Gaskets etc.of size: 100mm dia (For

fire pump room & Accessories)

[21] Supplying, Installation, Testing and commissioning of C.I.Butterfly 1.00 No 3,787.50

valve conforming to I.S:13095 class PN 16 rating with Fittings,

Flanges, Nutbolts, Washers, Gaskets etc.of size: 80mm dia. (For fire

pump room & Accessories)

[22] Providing, fixing, testing and commissioning of C.I. Dual plate type 2.00 No 18,109.30

Non-Return Valve class PN 16 rating with fittings, flanges, nutbolts,

washers, gaskets etc.of sizes: 150mm dia (For fire pump room &

[23] Providing, fixing, testing and commissioning of C.I. Dual plate type 1.00 No 6,615.50

Non-Return Valve class PN 16 rating with fittings, flanges, nutbolts,

washers, gaskets etc.of sizes: 80mm dia (For fire pump room &

[24] Supplying, Installation, Testing and commissioning of Rubber 2.00 No 15,806.50

Bellow conforming to I.S:Standard class PN 16 rating with Fittings,

Flanges, Nutbolts, Washers, Gaskets etc.of size: 150mm dia. (For

fire pump room & Accessories)

[25] Supplying, Installation, Testing and commissioning of Rubber 1.00 No 7,958.80

Bellow conforming to I.S:Standard class PN 16 rating with Fittings,

Flanges, Nutbolts, Washers, Gaskets etc.of size: 80mm dia. (For fire

pump room & Accessories)

[26] Supply, Installation, Testing and Commissioning of S.S. Ball Valves 10.00 No 818.10

with all fittings required. 25mm dia. (For fire pump room &

[27] Supply, Installation, Testing and Commissioning of S.S. Ball Valves 6.00 No 585.80

with all fittings required. 15mm dia. (For fire pump room &

[28] Providing, fixing, testing and commissioning of Above Ground GI. 12.00 Rmt 2,939.10

ERW B Class Heavyduty pipes as per IS: 1239 (upto 150 mm dia.)

and IS: 3589 (upto 200 mm dia. And above) including cutting,

screwing, welding etc. and providing all fittings like flanges, bends,

tees, elbows, reducers, clamps, hangers etc. with painting of one

coat of primer and 2 or more coats of synthetic enamel paint of

approved make / shade complete as per specification. 150mm dia

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[29] Providing, fixing, testing and commissioning of Above Ground GI. 286.00 Rmt 2,009.90

ERW B Class Heavyduty pipes as per IS: 1239 (upto 150 mm dia.)

and IS: 3589 (upto 200 mm dia. And above) including cutting,

screwing, welding etc. and providing all fittings like flanges, bends,

tees, elbows, reducers, clamps, hangers etc. with painting of one

coat of primer and 2 or more coats of synthetic enamel paint of

approved make / shade complete as per specification. 100mm dia

[30] Providing, fixing, testing and commissioning of Above Ground GI. 18.00 Rmt 1,504.90

ERW B Class Heavyduty pipes as per IS: 1239 (upto 150 mm dia.)

and IS: 3589 (upto 200 mm dia. And above) including cutting,

screwing, welding etc. and providing all fittings like flanges, bends,

tees, elbows, reducers, clamps, hangers etc. with painting of one

coat of primer and 2 or more coats of synthetic enamel paint of

approved make / shade complete as per specification. 80mm dia

[31] Providing, fixing, testing and commissioning of Above Ground GI. 12.00 Rmt 646.40

ERW B Class Heavyduty pipes as per IS: 1239 (upto 150 mm dia.)

and IS: 3589 (upto 200 mm dia. And above) including cutting,

screwing, welding etc. and providing all fittings like flanges, bends,

tees, elbows, reducers, clamps, hangers etc. with painting of one

coat of primer and 2 or more coats of synthetic enamel paint of

approved make / shade complete as per specification. 25mm dia.

[32] Providing, fixing, testing and commissioning of Under Ground GI. 24.00 Rmt 2,484.60

ERW B Class Heavyduty pipes as per IS: 1239 (upto 150 mm dia.)

and IS: 3589 (upto 200 mm dia. And above) including cutting,

screwing, welding etc. and providing all fittings like flanges, bends,

tees, elbows, reducers, clamps, hangers etc. with Anti Corrosive

Treatment for underground pipe acrossing the road and plant

enterance lines with primer & one coat of 3 MM thick anti

corrosive tape. 100mm dia

[33] Excavation and back Filling of soft soil for under ground pipe line of 24.00 Rmt 373.70

0.6 mtr. Deep from the ground level. (Depth 0.6 mtr * 0.8 mtr

[34] Providing, fixing, testing and commissioningMS steel supports with 700.00 Kg 131.30

Channels & Angle supports for Pumps, Hydrant and Sprinklers pipe

[35] Supplying, installing and commissioning of Foot Valve with,suitable 2.00 No 13,907.70

flanges, nuts, bolts, gaskets etc. complete. 100mm dia

[36] Supplying, installing and commissioning of Foot Valve with,suitable 1.00 No 7,524.50

flanges, nuts, bolts, gaskets etc. complete. 80mm dia

[37] Fire Fighting Equipement Providing, fixing, testing and 6.00 No 4,151.10

commissioning of SS Single Headed Oblique Pattern Hydrant

Landing Valves as per IS: 5290 with 80 mm dia flanged inlet &

mm dia female outlet complete with cap and chain etc.

[38] Providing, fixing, testing and commissioning of SS Branch Pipe with 6.00 No 1,313.00

nozzle of 25 mm nominal bore outlet suitable to fit with standard

instanteneous type 63 mm dia coupling. As per IS:903

[39] Providing, fixing, testing and commissioning of 63 mm dia 15m 12.00 No 4,605.60

long RRL Hose Pipe with 63 mm dia.Type A Male and female

Stainless Steel couplings duly binded with GI wire, rivets etc.

conforming to IS 636 as required.

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[40] Providing, fixing, testing and commissioning of weather proof 6.00 No 3,878.40

standard fire Hose Cabinet wall mounting type 18 Guage. (750 x

600 x 250) having Double Opening with M.S. fabricated stand,

necessary locking arrangement by allan key.

[41] Providing, fixing, testing and commissioning of Wall mounting Fix 6.00 No 6,060.00

type First aid Fire Hose Reel with drum, hanging bracket, 36 M x

mm dia high pressure hose reel tubing as per IS:884 with shut

nozzle and ball valve and all required accessories.

[42] Providing, fixing, testing and commissioning of Two Way Fire 1.00 No 5,464.10

Brigade Inlet for Draw Out Connection with 100mm dia Foot Valve.

blank cap and chain with necessary fittings, flanges, nutbolts etc.

(Make: Shah Bhogilal/Safex/Winco)

[43] Providing, fixing, testing and commissioning of 25 mm dia Air 2.00 No 1,646.30

Release Valve and Ball Valve assembly on top of each riser for Air

release system.

[44] On-Off Pump Trigger System. Providing, fixing, testing and 2.00 No 10,433.30

commissioning of On-Off Switch.

[45] Providing, fixing, testing and commissioning of 3 Core X 1.5 Sqmm 50.00 Rmt 161.60

flexible Cable with PVC Condiut.

[46] Providing, fixing, testing and commissioning of below Auto Glow 30.00 No 252.50

Signages. Emergency Exit 4” X 12”

[47] Providing, fixing, testing and commissioning of below Auto Glow 10.00 No 272.70

Signages. Fire Fighting Equipements .8” X 12”

[48] Providing, fixing, testing and commissioning of below Auto Glow 15.00 No 252.50

Signages. Fire Extinguisher 4” X 12”

[49] Providing and fixing of conventional manual call point 3.00 No 818.10

[50] Providing and fixing of conventional horn cum strobe 3.00 No 1,050.40

[51] SITC Of Conventional Fire Alarm Panel 1.00 No 11,635.20

[52] Providing and fixing of 2x1.5 sqmm fire alarm armoured cable, 300.00 Rmt 121.20

600/1000V rated with annealed copper conductor having XLPE

insulation, steel wire armouring &FRLS outer sheath complete as

[53] Providing & laying cement concrete 1: 4 : 8 ( 1 Cement : 4 Coarse 0.90 Cum 3,676.04

sand : 8 graded B.T stone aggregate 20mm nominal size) Curing

comp. including cost of form work in foundation and plinth

[54] Brick work using common burnt clay building bricks having crushing 10.50 Cum 4,289.33

strength not less than 35 kg./Sq.Cm. In Superstructure in Cement

Mortar 1:6 (1-Cement : 6-fine sand) (B) Conventional

[55] Providing and laying cement concrete 1:3:6 (1- Cement : 3- Coarse 0.70 Cum 3,996.68

sand : 6- crushed stone aggregates 20 mm nominal size) and curing

complete including cost of formwork in (A) Wall Caps / Coping

[56] Providing and laying cement concrete 1:2:4 (1- Cement : 2-Coarse 1.00 Cum 6,506.53

sand : 4- graded stone aggregates 20 mm nominal size) for

reinforced concrete Chhajjas not exceeding 10cm. thickness upto

floor two level including finishing the exposed surfaces with

cement mortar 1:3 (1-cement, 3 Fine sand) to give a smooth and

even surface centering and formwork and curing complete

excluding cost of reinforcement.

[57] Providing 15 mm thick cement plaster in single coat on Rough 51.00 Sqm 194.07

(Similar) side of single or half brick walls for interior plastering upto

floor two level and finished even and smooth in (i) Cement mortar

1:3 (1-cement : 3-sand)

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[58] 20mm thick sand faced cement plaster on walls upto height 10 51.00 Sqm 335.65

metres above ground level consisting of 12mm thick backing coat

of C.M. 1:3 (1-cement : 3-sand) and 8mm thick finishing coat of

C.M. 1:1 (1-cement : 1-sand) etc. complete.

[59] Wall painting (three coats) including priming coat with plastic 51.00 Sqm 119.42

emulsion paint of approved brand and manufacture on

undecorated wall surfaces to give an even shade including

thoroughly brushing the surface free from mortar droppings and

other foreign matter and sand papered smooth including applying

priming coat etc. complete.

[60] Finishing wall with Weather Proof Acrylic Emulsion Exterior Paint 51.00 Sqm 218.89

on wall surface (two coat) to give and even shade and of approved

brand and manufacture including thoroughly brooming the surface

to remove all dirt and remains of loose powered material.

[61] Providing and Fixing Machine cut, free edges, machine polished 6.00 Sqm 2,330.93

Granite stone slab 18 mm thick (single piece not more than 150 cm

) for Doors/Windows sill and Jambs cladding with the help of

anchore fastening as per design including full molded round front

edge and 1 cm nosing and laid on 20 mm thick cement mortar 1:6

( 1 cement:6 coarse sand) jointed with grey cement slurry including

rubbing and polishing finishing and etc complete.

[62] Both side laminate finish flush door. Providing Material & Labour 2.60 Sqm 4,056.63

charge for making laminate finish Flush Door (finished size of

door is 40 mm) of size 975 mm x 2400 mm considering waterproof

flush door sheet of 38 mm thkness covered both side by 1.0 mm

thick Laminate supprted by SS -314 finish hinges. All exposed

framing of 65 mm x12 mm made by teak wood bidding complete

with polish. Finishing with all necessary hardwares like handles,

conceal mortise locks, cylinders with 6 nos of keys, stopers,tower

bolt,MS nails, SS-314 screws etc. as per details given in drawing

and as per instructions of Architect/Engineer In charge. Please see

the Attached Make List for Apporoved Makes.

[63] Providing and fixing Anodized Alluminum Section Jindal Deluxe 4.60 Sqm 3,230.13

Sliding Window System 27mm series THREE track window as

shown in elevation, shutter with 5mm thick transparent plain float

glass, with transparent silicon sealant with allu. anosized coated

fittings and fixture etc complete.

[64] Structural steel work ( Confirming to IS 4923-1997) riveted, bolted 1090.00 Kg 127.95

or welded in builtup for all type sections, in framed work, including

cutting, hoisting, fixing in position and applying a priming coat of

approved steel primer all complete as per the structural designs

and directions of Engineer in charge.

[65] Providing corrugated G.I. sheet of class-3 roofing fixed with 60.00 Sqm 727.13

glavanished iron J or L Hooks, Bolts and nuts 8mm diameter with

bitumen and G.I. limpet washer or G.I. limpet washer. filled with

white lead complete excluding the cost of purlins, Rafters and

Trusses. (1) 0.80 m thick sheet.

[66] Providing and fixing pre-cast concrete kerb stone of gray cement 256.00 Rmt 384.96

based concrete block 30cm length, 30cm height and 15cm thick of

M200 grade concret as per approved design and including

excavation for fixing in proper line and level, filling the joint with

C:M 1:3 (1cement:3fine sand) etc. complete.

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[67] Road marking with hot applied thermoplastic paints with 85.00 Sqm 367.72

reflectorising glass beads on bitumin surface providing and laying a

hot applied thermoplastic compound 2.5 mm thick including

reflectorising glass beads @ 250gms per sqm area, thickness of

2.5mm is excluding of surface applied glass beds as per IRC:35-

2015. The finished surface to be level, uniform and free from

streaks and holes. zebra patta /bump patta lane/center line/ edge

line/cut patta. The white color marking should provide liminance

coefficinet on cemend road shalll be min 130 mcd/m2/lux and

Asphalt road shall be min 100 mcd/m2/lux during the service life

during the day time. The marking should meet the performance

criteria for night time reflectivity, wet reflectivity and skid

resistance as mentioned in the section-15 of IRC 35-2015.

Warranty for the Retro reflectivity should be two years.

[68] Providing and Fixing 15 mm thick 300 mm x 300 mm Tactile 88.00 Sqm 1,225.99

Warning Tiles (Attention Tiles ie. Tactile Warning Surface Indicator

(TWSI)) of Johnsan Endura Tac Button Yellow Plus or equvqlent

make in flooring laid on 20 mm thick cement mortar 1:6 (1 cement:

6 coarse sand) on new surface and jointed with cement slurry

Including finished with flush pointing & cleaning the surface for all

floors as per detailed drawing etc. complete as directed by

Architect or Engineer in charge. The tiles shall be Anti Skid,

Chemical Resistant, Fade Proof, Frost - Ileat & Weather Proof, High

Flexural Strength, Highly Durable, Stain Resistance All Tactile

Warning Tiles meet the specific size and dimension standards as

required by 150/FDIS

[69] Providing and fixing acrylic multilingual Braille (raised dots) 40.00 No 2,041.28

DIRECTIONAL SIGNBOARDS of size 225 x 150mm designed as per

accessibility standards and having 3.5mm thick acrylic base plate

with Upper Case San Serif words made of white acrylic non glare

cut out letters of height 15mm raised not less than 0.8mm above

base plate and the equivalent word written in Hindi with

Devanagari non glare acrylic letters of height 15mm raised not less

than 0.8mm above base plate and having a non-glare acrylic cut

arrow pointing in the required direction. Each signboard to be fixed

as per manufacturers specifications on the wall at the approved

location and at a height of 1200mm from FFL complete as per

design / specifications and guidelines as per the entire satisfaction

of the Engineer.

[70] PROVIDING & FIXING BRAILE INDICATOR OF SIZE 170 MM X 35MM 20.00 Rmt 1,093.72

FOR HANDRAILS OF THE APPROVED DESIGN AND MAKE H BRAILE

DOTS RAISED 0.5 MM ABOVE BASE PLATE TO BE INSTALLED AT

SPECIFIC LOCATIONS AS PER DIRECTION ENGINEER IN CHARGE.

[71] Providing and Fixing a set of wall mounted 38 mm dia U shaped 2.00 Set 3,182.55

horizontal stainless steel collapsible grab bar 38mm vertical

stainless steel fixed grab rail of grade SS 304 from round pipe

supported and 75 mm dla 8 mm thick SS 304 base flange on wall

Including anchor fasteners, nuts, accessories as per detailed

drawing etc. complete as directed by Architect or Engineer in

[72] Providing and Fixing Size: L 75mm x W 75mm x II 1200; 15 mm 24.00 No 792.55

thick U shape corner Rubber Reflective Guards with yellow

reflective Patti fixing on RCC/brick surface Including all fitting and

material charges & It shall be Chemical Resistant, Fade Proof, Frost -

Heat & Weather Proof, High Flexural Strength, Highly Durable,

Stain Resistance as per detailed drawing etc. complete as directed

by Architect or Engineer in charge.

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[73] Providing and fixing of acrylic, non-glare, tactile audio pictorial 2.00 No 50,500.00

building layout as per the approved size, design and make, having

3mm thick acrylic non glare base plate of the approved colour and

non-glare acrylic cut out symbols raised 3mm above base plate and

Grade 2/ Grade 1 Braille to be integral with the sign face and be

raised 0.5mm above base plate. The map to be installed at the

specified location as per accessibility standards, shall be oriented to

the position of the viewer and to be installed at a height of

mm from the finished ground/ floor level and using the necessary

hardware specified by the manufacturer and to be installed up to

the height of 800 mm from the finished ground/ floor level and

using the necessary hardware specified by the manufacturer and to

be installed complete as per design / specifications and guidelines

as per the entire satisfaction of the the Engineer-in-charge.

[74] Providing & Fixing tactile layout plan of size 900mm x 600mm as 2.00 No 38,380.00

approved design, made of 3.0mm thick acrylic non glare base plate

and non glare cut out symbols with Braille on which Individual

facility points, like Inquiry, reception, restrooms, medical room /

first ald, cafeteria or breakout area, lounge, meeting room,

conference room etc. present the respective floors with pictograph

wherever needed all in tactile raised by minimum of 1.0mm to

2mm In various colours to make it legible for seniors, partial vision

Impaired etc. All the facility names should be in Braille, along with

English or Hindi. The entire block of tactile signs should be

mounted on wall for easy reading. The map to be Installed at

specified locations and installed at a height of 800mm.

[75] APPROVAL FIRE SYSTEM FROM LOCAL FIRE AUTHORITY Getting of 1.00 Job 1,51,500.00

Fire Fighting System Approval from local fire authority with all

other charges and documentations for getting No Objection

[76] Providing and Fixing 6 mm thick Lexan Polycarbonate multi wall 30.00 Sqm 1,441.90

roofing sheet fixed with hilti screw and rubber silicon sealer and

alluminium strip of size 50 x 3 mm etc complete as directed by

Engineer in charge

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[77] Providing Prefebricated Security Cabin 6 Ft (L) x 6 Ft (W) x 8 Ft (H) 1.00 No 60,600.00

M.S. Built having Main Steel Frame and Walls made of Puff or FRP

material and having features like Sliding Window , weatherproof

Electrical fittings , Fan , Main Door with locking arrangement etc,

complete and Color as directed including Labour , Transportation

etc. complete as directed by Engineer in Charge.

Thirty One Lakh Sixty Two Thousand Seven Hundred Sixty One Rupees and Thirty Five Paisa Only

I/We am/are willing to carry out the work at…………………………………………….% above/below percent (Should be written in figures and words)

of the estimated rate mentioned above. Amount of my / our tender works out as under.

Estimated amount put to tender Estimated amount put to tender

Deduct…………………………% below Add…………………………% Above

In Worlds In Worlds

(* Please strike out whichever is not applicable).

1. The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-Charge for which

no extra payment shall be made.

2. The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3. GST and Income tax TDS will be deducted at a source while making payments of bills

4. In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-10/2017 Cement

Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where there is a change as per actual mix design

the cost of difference of cement consumption have been deducted from the rate of original item at the rate of input rate

mentioned in all the tender.

5. Credit of dismantled materials of amount of Rs. 0.00/- must be recovered from contractor's 1st R.A. bill.

6. All duties, taxes, and other levies except GST payable by the contractor under the contract, or for any other cause shall be included

in the rates, prices and total Bid Price submitted by the Bidder. (GST will be paid extra)

Dated Signature of Deputy Executive Engineer Executive Engineer

the Contractor. R & B Sub-Division, R & B Division,