INSTALLATION OF PANEL BOARDS AND ENCLOSURES AT MATSYAFED NYLON TWINE FACTORY, PARAVOOR, ALAPPUZHA

Amount

INSTALLATION OF PANEL BOARDS & ENCLOSURES AT MATSYAFED NYLON TWINE FACTORY, PARAVOOR, ALAPPUZHA

Supply, installation, testing and commissioning of Floor Mounting Cubical Type Switch Board Panel suitable for 415 V, Three Phase, 4 Wire 50 Hz AC supply system having sufficient front surface area fabricated in compartmentalized design from CRCA sheet steel of 2 mm thick for frame works, covers and gland plates, cleaning and finishing complete with 7 tank process for Powder Coating in approved shade and then provided with Clear Coating, having 400 Amps capacity type TPN Aluminium alloy busbars of high conductivity, DMC / SMC / FRP busbar supports, with short circuit withstand capacity of 31 MVA for 1 Sec., bottom base channel of MS section not less than 100 mm x 50 mm x 5 mm thick, fabrication shall be done in transportable sections, entire panel shall have a common copper earth bar of size 25 mm x 6 mm at the rear with 2 Nos. earth stud, solid connections from main busbars to switch gears with approved size of Aluminium busbars and control wiring with 2.5 / 1.5 Sq.mm FRLS (Flame Retardant Low Smoke) or HRFR (Heat Resistant Flame Retardant) PVC insulated single core copper conductor cables, cable alleys etc. complete as required. For all MCCBs Ics shall be 100% Icu. The panel shall conform to the Electrical Inspectorate standards and it shall only be manufactured after getting approval from the Engineer-in-charge, Consultant and the Electrical Inspectorate. BUSBAR 1 Runs of 63 mm x 10 mm Aluminium for each Phase 1 Runs of 40 mm x 10 mm Aluminium for Neutral INCOMER 1 Set - RYB Indication Lamps with Control MCBs 1 Nos - 400A 36kA 4P Microprocessor Based MCCB with ROM, Spreader, Shunt Release, ON-OFF-TRIP Auxiliary Contacts and ON (Red), OFF (Green), TRIP (Amber) Indication Lamps with Control MCBs 3 Nos - 400/5A 10VA CL:1 Resin Cast CT 1 Nos - Digital Multifunction Meter measuring V, A, F, KWH, KVA, PF with Control MCBs 1 Nos - Digital Earth Leakage Relay with CBCT and Control MCBs SURGE PROTECTION DEVICE 1 Nos - 4 Module DIN Rail Mounting Type 1 + Type 2 / Class 1 + class II 100kA SPD on the Incoming / Outgoing Side of Incomer MCCB along with Green and Red Indication Lamps with Control MCBs [The connections to RYB Phases, Neutral and Earth shall be done using 16 Sq.mm FRLS (Flame Retardant Low Smoke) or HRFR (Heat Resistant Flame Retardant) PVC insulated single core copper conductor cables with less than 0.45m in length] OUTGOINGS 1 Nos - 160A 25kA 4P Thermal Magnetic Type MCCB having 70 to 100% Setting Provision with ROM, Spreader, ON-OFF-TRIP Auxiliary Contacts and ON (Red), OFF (Green), TRIP (Amber) Indication Lamps with Control MCBs 5 Nos - 125A 25kA 4P Thermal Magnetic Type MCCB having 70 to 100% Setting Provision with ROM, Spreader, ON-OFF-TRIP Auxiliary Contacts and ON (Red), OFF (Green), TRIP (Amber) Indication Lamps with Control MCB 1 Nos - 100A 25kA 4P Thermal Magnetic Type MCCB having 70 to 100% Setting Provision with ROM, Spreader, ON-OFF-TRIP Auxiliary Contacts and ON (Red), OFF (Green), TRIP (Amber) Indication Lamps with Control MCB 1 Nos - 80A 25kA 4P Thermal Magnetic Type MCCB having 70 to 100% Setting Provision with ROM, Spreader, ON-OFF-TRIP Auxiliary Contacts and ON (Red), OFF (Green), TRIP (Amber) Indication Lamps with Control MCB

Supply, installation, testing and commissioning of Column / Wall Mounting Cubical Type Switch Disconnector Enclosure suitable for 415 V, Three Phase, 4 Wire 50 Hz AC supply system having sufficient front surface area fabricated in compartmentalized design from CRCA sheet steel of 2 mm thick for frame works, covers and gland plates, cleaning and finishing complete with 7 tank process for Powder Coating in approved shade and then provided with Clear Coating, having 125 Amps capacity type TPN Aluminium alloy busbars of high conductivity, DMC / SMC / FRP busbar supports, with short circuit withstand capacity of 31 MVA for 1 Sec., entire panel shall have a common copper earth bar of size 25 mm x 3 mm at the rear with 2 Nos. earth stud, solid connections from main busbars to switch gears with approved size of Aluminium busbars and control wiring with 2.5 / 1.5 Sq.mm FRLS (Flame Retardant Low Smoke) or HRFR (Heat Resistant Flame Retardant) PVC insulated single core copper conductor cables, cable alleys etc. complete as required. The panel enclosure shall conform to the Electrical Inspectorate standards and it shall only be manufactured after getting approval from the Engineer-in-charge, Consultant and the Electrical Inspectorate. BUSBAR 1 Runs of 32 mm x 6 mm Aluminium for each Phase 1 Runs of 25 mm x 6 mm Aluminium for Neutral INCOMER 1 Set - RYB Indication Lamps with Control MCBs 1 Nos - 125A 4P Switch Disconnector OUTGOINGS 2 Nos - 63A 4P Switch Disconnector

Supply, installation, testing and commissioning of Column / Wall Mounting Cubical Type Switch Disconnector Enclosure suitable for 415 V, Three Phase, 4 Wire 50 Hz AC supply system having sufficient front surface area fabricated in compartmentalized design from CRCA sheet steel of 2 mm thick for frame works, covers and gland plates, cleaning and finishing complete with 7 tank process for Powder Coating in approved shade and then provided with Clear Coating and control wiring with 2.5 / 1.5 Sq.mm FRLS (Flame Retardant Low Smoke) or HRFR (Heat Resistant Flame Retardant) PVC insulated single core copper conductor cables, cable alleys etc. complete as required. The panel enclosure shall conform to the Electrical Inspectorate standards and it shall only be manufactured after getting approval from the Engineer-in-charge, Consultant and the Electrical Inspectorate. COMPONENTS 1 Set - RYB Indication Lamps with Control MCBs 1 Nos - 63A 4P Switch Disconnector

Supply, installation, testing and commissioning of Neutral CT Enclosure with front door for mounting existing duly tested Resin Cast CT having sufficient front surface area fabricated in compartmentalized design from CRCA sheet steel of 2mm thick for frame work and door, cleaning and finishing complete with 7 tank process for Powder Coating in approved shade and then provided with Clear Coating, having openings in both top and bottom for fixing copper bar of required size, fixed on already fabricated and painted MS Structural supports etc. complete as required. The enclosure shall conform to Electrical Inspectorate Standards and it shall only be manufactured after getting approval from the Engineer-in-charge and the Consultant

1 Nos - Digital Multifunction Meter measuring V, A, F, KWH, KVA, PF with Control MCBs

1 Nos - Digital Earth Leakage Relay with CBCT and Control MCBs SURGE PROTECTION DEVICE

1 Nos - 4 Module DIN Rail Mounting Type 1 + Type 2 / Class 1 + class II 100kA SPD on the Incoming / Outgoing Side of Incomer MCCB along with Green and Red Indication Lamps with Control MCBs [The connections to RYB Phases, Neutral and Earth shall be done using 16 Sq.mm FRLS (Flame Retardant Low Smoke) or HRFR (Heat Resistant Flame Retardant) PVC insulated single core copper conductor cables with less than 0.45m in length]

OUTGOINGS

1 Nos - 160A 25kA 4P Thermal Magnetic Type MCCB having 70 to 100% Setting Provision with ROM, Spreader, ON-OFF-TRIP Auxiliary Contacts and ON (Red), OFF (Green), TRIP (Amber) Indication Lamps with Control MCBs

5 Nos - 125A 25kA 4P Thermal Magnetic Type MCCB having 70 to 100% Setting Provision with ROM, Spreader, ON-OFF-TRIP Auxiliary Contacts and ON (Red), OFF (Green), TRIP (Amber) Indication Lamps with Control MCB

1 Nos - 100A 25kA 4P Thermal Magnetic Type MCCB having 70 to 100% Setting Provision with ROM, Spreader, ON-OFF-TRIP Auxiliary Contacts and ON (Red), OFF (Green), TRIP (Amber) Indication Lamps with Control MCB

1 Nos - 80A 25kA 4P Thermal Magnetic Type MCCB having 70 to 100% Setting Provision with ROM, Spreader, ON-OFF-TRIP Auxiliary Contacts and ON (Red), OFF (Green), TRIP (Amber) Indication Lamps with Control MCB

8.CENTERING & SHUTTERING: (Centering and shuttering for different category of work may be considered separately.)

9. SOLID BLOCK MASONRY: Min. average compressive strength as per IS shall be 40-50kg/cm2 and has to be assessed by testing at Govt. lab. ( Variation in rate due to change in size of block and level of floor as per DSR/PRICE has to be considered)

10.PLUMBING & SANITARY FITTINGS: Note: Make of Water supply and sanitary items: Best branded ISI make Jaquar, Cera, Hindware, Parryware or eq. in the order of pref. Water pipe: Supreme, Finolex or eq. with IS and all fittings with IS.

6.VETRIFIED FLOOR TILES/ CERAMIC GLAZED WALL TILES: Make: Khajaria, Jhonson, RAK, NITCO, Cera or Eq. in the order of preference and prior sample approval from KEL, Client

15.ALUMINIUM WORK: Make: INDAL, JINDAL in the order of preference and prior sample approval from KEL, Client

10.Rigid PVCPipes/Casing & Capping - A-ONE/REPUTED MAKE with ISI , Precession, Balco, GEO

9. ACRYLIC SMOOTH EXTERIOR PAINT/ SYNTHETIC ENAMEL PAINT/WHITE CEMENT BASED PUTTY/ CEMENT PRIMER: Make: Asian, Berger, Nerolas or eq. in the order of pref.

11.ELECTRICAL: Note: Rate should be inclusive of preparation of schematic diagram and getting approval from KSEB/Electrical Inspectorate. Statutory fees paid to KSEB/EI shall be paid by us separately.

Make of Electrical equipments/materials

All electrical materials/equipments shall be of best branded items with ISI, strictly as per schedule specification

Panel Boards: CPRI certified reputed manufacturers make

MCB/ELCB/DB - L&T/LEGRAND/SCHNEIRDER or equivalent

Cables & wires - Finolex/KEI/POLYCAB/RPG/V-GUARD

Switches/Sockets/Regulators - SCHEIDER/ABB/HAVELS/LEGRAND or equivalent

Cable Glands & Sockets - REPUTED MAKE , Cosmos

Indicating Lamps - TEKINIC/RISHUB/STC, L&T, Schneider or equivalent

Ceiling/Exhaust fan: Havells, Orient, Usha, Crompton Greaves, Bajaj

A ONE AGENCIES (BID ID -1994148)

Tesla Consulting Engineers (BID ID -1994208)