PROVISION OF SOLAR CONTROL ROOM AT CGDHQ-01 PBR, PROVN OF SCREEN WALL AT MARRIED ACCOMODATION, ROAD FURNITURE, ADDN/ALTN TO GUARD POSTS AT SONARI JUNGLE PORBANDAR UNDER GE I CG PORBANDAR

Amount

SCHEDULE 'A'

Excavation in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cessipts, manholes, pier holes, etc. n exc 10 Sqm on plan and n exc 1.5m in depth and getting out in soft/disintegrated rock complete all as specified and directed.

Excavation in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cessipts, manholes, pier holes, etc. n exc 10 Sqm on plan and n exc 1.5m in depth and getting out in any type of soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick using soft/disintegrated rock all as specified.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick using any type of soil all as specified.

Removing excavated rock to a distance exc 500 mtr but n.exc 1.5 km and depositing where directed at a level n exc. 1.5 m above the starting point all as specified and as directed by engineer-in-charge.

Removing excavated soil to a distance n exc. 50 m and depositing where directed at a level n exc. 1.5 m above the starting point all as specified and as directed by engineer-in-charge.

M&L Hardcore of guage n.exc. 63mm, deposited spread & levelled in layers n.exc.15CM thick, watered & rolled/ rammed to a true surface using broken stone or boulders all as specified and as directed by engineer-in-charge.

M&L Moorum / Red bajri filling in floors or pavings laid in layers n.exc 15cm thick, spread, levelled and rammed including watering all as directed by Engr-in-Charge.

M&L Plain cement concrete, type D2, (1:4:8, using 40mm graded stone aggregates) as in foundation, filling and mass concrete etc all as specified and as as directed by engineer-in-charge. Note: The proportioning of cement and aggregate for mixing by weight shall be as directed by the Engineer-in-charge.

M&L PCC,, 1:2:4, type B0(using 12.5 mm graded stone aggregates) as in coping, bed blocks for hold fasts and similar works complete all as specified and directed.

M&L RCC nominal mix type A1, (1:1.5:3, using 20mm graded stone aggregates) as in foundation including raft footing foundation beam plinth beam bases for columns etc basement slab under reamed piles and mass concrete Note: The proportioning of cement and aggregate for mixing by weight shall be as directed by the Engineer-in-charge.

M&L RCC nominal mix type A1, (1:1.5:3, using 20mm graded stone aggregates) as in slabs supported onwalls, beams and colums in floors, roofs, landings, balconies, canopies ,deck slabs and in shelves and the like complete all as specified and directed by Engr-in-charge Note: The proportioning of cement and aggregate for mixing by weight shall be as directed by the Engineer-in-charge.

M&L RCC nominal mix type A1, (1:1.5:3, using 20mm graded stone aggregates) as in beams,cantilevers, bressumers and lintels over 1.5 mtr span complete all as specified and directed by Engr-in-charge. Note: The proportioning of cement and aggregate for mixing by weight shall be as directed by the Engineer-in-charge

M&L RCC nominal mix type A1, (1:1.5:3, using 20mm graded stone aggregates) as in Columns,pillars,piers, posts and struts Note: The proportioning of cement and aggregate for mixing by weight shall be as directed by the Engineer-in-charge.

M&L RCC nominal mix type A1, (1:1.5:3, using 20mm graded stone aggregates) as in chajjas, floors, roofs, landings, blaconies, canopies, deck slabs and in shelves and the like. Note: The proportioning of cement and aggregate for mixing by weight shall be as directed by the Engineer-in-charge.

supply only Integral water proofing compound

M&L Porbandar stone masonary, block in course, well bonded and bedded, built in CM 1:6 all as specified and as directed by engineer-in-charge.

Formwork to sides of concrete foundations, footings,bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter,for rough finished surfaces of flat concrete..

Form Work to sides of pillars/ columns square or rectangular ,for rough finished surfaces of flat concrete.

Form work to soffits of suspended slab such as roof slab floor slab landing and similer work not exceeding 200mm thick (horizontal or sloping) ,for rough finished surfaces of flat concrete.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers,lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc for rough finished surfaces of flat concrete.

Formwork to chajjas including edges ,for rough finished surfaces of flat concrete.

S & F 30mm thick 2nd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass, gauze etc but divided into squares, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads etc complete all as specified and directed by Engr-in-Charge.

S&F 2nd class hard wood plain,solid,straight chowkats and frames,wrought,framed rebated on the solid,rounded or chamfered,put together with glue pinned at joints

S & F 35mm thick 2nd class hard wood plain framed panelled shutter (any number of panels) with panels of timber flat on both sides, feather edged or of veneered particle board medium density, wood particle board with commercial face veneer etc complete all as specified and directed by Engr-in-Charge.

S & F 30 mm thick factory made solid panel PVC door shutter conforming to criteria of testing as per IS : 4020, consisting of frame made out of MS tube of 19 guage thickness & size 19x19mm for stiles and 15x15mm for top & bottom rails MS frames shall have a coat of red oxide primer of approved make and shall be covered with 5mm thick heat moulded PVC `C' channel of size 30x50mm forming stiles and 5mm thick 75mm wide PVC sheets for top rail lock rail and bottom rail on either side and 10mm (5mmx2) thick 20mm wide cross PVC sheet as gap insert for top rail and bottom rail panelling of 5 mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rail with 30 mm wide x 5 mm thick PVC sheet beading on either side and joined together with solvent cement, adhesive and an additional 5 mm thick PVC strip of 20 mm width is to be struck on the interior side of 'C' channel using PVC solvent adhesive complete as per manufacturers specifications & drawings ass as directed by Engineer-inCharge Make :- M/s Sintex Industries Ltd, M/s Rajshree Plastiwood Ltd,

S&F Factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with 19x 19mm MS square tubes, provided with EPDM rubber gasket throughout the frame fixed in opening complete as per manufacturer's specifications and as directed by Engineer-in-Charge Make :- M/s Sintex Industries Ltd, M/s Rajshree Plastiwood Ltd,

S&F Aluminium, anodised, barrel tower bolts 150 mm long of extruded section and fixed complete all as specified and as directed by Engr-in-Charge.

S&F 300mm long Aluminium alloy, anodised,sliding door bolt with hasp,staple (ISI Marked) (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S&F 150 mm long Extruded aluminium alloy handles, fabricated type,anodised (ISI Marked) complete all as specified and directed.

S&F Aluminium XPM Jalli 24 gauge thickness and fixed with aluminium wire staples complete all as specified and directed.

M&L Mild steel CRS TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia or securing with clips. etc complete all as specified and directed by Engr-in-charge.

M&L Mild steel CRS TMT bars 6 to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia or securing with clips. etc complete all as specified and directed by Engr-in-charge.

All as per above item No.35.00 but 5mm dia and over upto 10mm dia as in stirrups, spacers and binders etc complete all as specified and directed by Engr-in-charge.

M&L APP based membrane course roof treatment in layers with following provisions:- (i) Applying one coat of bitumen's primer polymerized primer oil based coat, evenly @ 0.3 litre/Sqm as priming coat to the prepared surfaces, till the surfaces is properly impregnated and the solvent oil in the base primer shall be allowed to evaporated completely. (ii) Applying APP based pre-fabricated with non woven polyester reinforced membrane stabilized with fibre glass strands and top with grey mineral slates 3mm thick and weight not less than 3.50 Kg/Sqm by torch application method. (iii) Applying a coat of solar reflective bituminous aluminium paint @ 0.10Kg/Sqm over mineral surface.

S&F 18/19mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work as in cupboards, shutters, shelves, cabinets, pelmets etc including fixing 18 mm wide 6 mm thick beading all around of 1st class HW (Teak) complete all as specified & directed by Engr-in-charge.

M&L 75 mm thick, Plain cement concrete, type C1, (1:3:6 using 40mm graded stone aggregate) as in plinth protection finished fair and even without using extra cement. complete all as specified and as directed by Engr-in-Charge.

M&L 75mm thick, Plain Cement concrete, type D-2, 1:4:8 (using 40mm graded stone aggregate) as in sub base of floors even and rough finished to receive topping layer complete all as specified and as directed by Engr-in-Charge.

M&L 25 mm thick, Plain cement concrete, type B1, (1:2:4 using 20mm graded stone aggregate) as in floor finished even and smooth without using extra cement complete all as specified and as directed by Engr-in-Charge.

M&L Glazed coloured ceramic tiles in verticle surfaces 450x 300x 7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match over backing bedding layer 10mm thick 1:4 and pointed in white or coloured cement to match etc complete all as specified and directed by Engr-in-charge.

M&L Joint free coloured non-skid ceramic tiles 8 to 9 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry over screed bed 15 mm thick 1:6 and pointed in white or coloured cement to match complete all as specified and as directed by Engr-in-Charge.

ditto as per item No 41, as in skirting.

M&L Rendering 10 mm thick on fair face of brick work or concrete surfaces in CM 1:6 finished even and smooth wiithout using extra cement.

M&L Rendering 15 mm thick in CM (1:3) using water proofing compound as per manufacturer instruction as in roof and chajjas complete all as directed by Engr-in-Charge. Note : Water proofing compound will be measured and paid separately.

M&L Rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified.

M&L Rendering 5mm thick, cement plaster, in cement mortar (1:4) mixed with integral water proofing compound as per manufactures instruction, over 10mm thick cement plaster in cement mortar (1:6) on fair faces of stone masonry walls or finished even and smooth without using extra cement in any height, complete all as specified and directed. Note:- Water proofing compound shall be measured and paid separately)

M&L Granite work 18 to 20 mm thick (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of granite over screed bed or bedding layer of 15 mm thick 1:6 etc. complete all as specified and as directed by Engr-in-Charge.

M&L Rendering 15 mm thick in cement mortar 1:6 on fair faces of PCC block masonry and finished even and smooth without using extra cement

M&L Rendering 5mm thick in CM(1:3) on ceiling finished even and smooth without using extra cement complete all as specified and as directed by Engr-in-Charge.

M&L Preparation of new plastered surfaces of walls and applying two coats of cement based paint over a coat of primer complete all as specified.

M&L Preparation of new plastered surfaces of ceilings and applying three coats of white wash complete all as specified.

M&L Preparation of new plastered surfaces of walls and applying three coats of white wash complete all as specified.

M&L Preparation of new plastered surfaces of ceiling and applying two coats of oil bound distemper over a coat of alkali resistant primer all as specified and directed.

M&L Preparation of newly plastered surfaces of wall and applying Two coats of OBD over a coat of alkali resistant primer complete over 3mm thick wall care putty on walls all as specified and as directed by Engr-in-Charge.

S&F 4 mm thick Sheet glass,ordinary quality and glazing with oil putty in square exc 0.50sq. m in each pane all as specified and as directed by engineer-in-charge.

S&F 5.5 mm thick Sheet glass,ordinary quality and glazing with oil putty in square n exc 0.5sq. m in each pane all as specified and as directed by engineer-in-charge.

S&F 4mm thick Figured glass, pin head type and glazing with oil putty / rubber neoprene in squares n exc 0.5 sq. m in each pane.

M&L for preparation of new plastered surfaces of wall and applying two coats of weather proof acrylic exterior emulsion paint over a coat of acrylic primer all as per the manufacturers instructions, complete all as specified and directed by Engr-in-charge.

M & L Preparation of new wooden surfaces of any description, not otherwise described over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer of approved shade complete all as specified and as directed by Engr-in-Charge.

S&F 500 Litre three layered capacity rotational moulded polythylene water storage tanks (cylindrical, vertical with closed top ) hoisted and fixed in position all as specified and directed including provision of 200mm long 50mm bore GI nipples for inlet, outlet, overflow, drain out pipe including provision of check nuts.

S&L 25 mm OD, CPVC pipes, of SDR -11 & plain CPVC SDR fittings for Hot/cold water for sizes mentioned below including all fittings and solvents and special fittings like brass elbow, brass tee, male threaded brass adaptor, female threaded brass adaptor etc, Unions, Flange and tank adapter all as per manufacturers recommendations and as specified.

S&L 16mm OD, CPVC pipes, of SDR -11 & plain CPVC SDR fittings for Hot/cold water for sizes mentioned below including all fittings and solvents and special fittings like brass elbow, brass tee, male threaded brass adaptor, female threaded brass adaptor etc, Unions, Flange and tank adapter all as per manufacturers recommendations and as specified.

S&F PVC connections 15mm size with PTMT nuts of length 600mm Make : Prayag and equivalent as approved by Engr-in-Charge

S&F 75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches, in floors, fixed to walls including making good the disturbed surfaces complete all as specified.

S&F 75mm dia PVC (SWR) bend of any radius complete all as specified and directed.

S&F 75 mm bore PVC (SWR) floor trap,plain with grating incl jointing to waste pipe with solvent cement.

S&F vitreous china wash down water closet, squatting pan ,'Orissa pattern', size 580 x440 mm, white,with integral foot rests .

S&F 10 lit.capacity PVC valveless, syphonic action type, flushing cistern,low level, white, with inlet,ball valve, float and handle including brackets complete all as specified. Make : Prayag (Cat Pat No-501) or equivalent as approved by Engr-in-Charge

S & F Vitreous china wash hand basin, white, flat back, of size 550 x 400 mm including waste chain and plug or porcelain stopper but including cutting for and pinning in ends of brackets all as specified and directed. Make: CERA Cat Pat No-S2030121W or Equivalent

S&F 5.5 mm thick Sheet glass shelf and 120mm wide with copper alloy, chromium plated bracket guard and railing 60 cm long all as specified and as directed.

S&F Vitreous china urinal, full stall type, white, (excluding flushing cistern, flush pipe and waste pipe) all as specified and as directed.

S&F 15mm dia Fancy type Bib taps, with flange chromium plated cast copper alloy with capstan head complete all as specified and directed. Make : Prayag (Cat Pat No-8306) or equivalent as approved by Engr-in-Charge

S&F 125mm brass chromium plated shower rose of bore 15mm with swivel joints,

S & F 15 mm bore Stop Valve Cast Copper Alloy fancy type, Chromium plated with long shank and cup, high pressure, with crutch, screwed both ends for iron pipe or for unions and fixed. Make : Prayag (Cat Pat No-8518) or equivalent as approved by Engr-in-Charge

M&L 15 mm dia Pillar taps, fancy type cast copper alloy, with capstan heads, chromium plated,screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed Make: CERA Cat Pat No-F1005101 or Equivalent complete all as specified and directed by Engr-in-Charge.

Demolition of brick work or stone masonary including all quoins,arches, pillars, but excluding ashlar facings, dressed stone work and precast concrete articles built in cement mortar complete all as specified and directed.

Demolition of cement concrete (reinforced) (reinforcement cut as requried to facilitate demoliton of any description and in any position n.exc 15 cm thick (below or above GL) and disposal on debits up a distance n.exc 100m where directed

Demolition of cement concrete in floors and pavings n.exc15 cm thickness (below or above ground level)

S&F Butt hinges, 100 mm medium weight, stainless steel complete all as specified and as directed by Engr-in-Charge.

S&F Butt hinges, 75 mm medium weight, stainless steel complete all as specified and as directed by Engr-in-Charge.

S&F powder coated Anodised aluminium frame and shutters (minimum thickness of powder coating 50 micron) for doors, shutters, sliding windows and windows ventilators with or without rebates including joining cleats for fixing etc. complete all as specified and as directed by Engr-in-Charge. Note: Rollers for sliding windows, rubber beading, starlock shall be measured and paid separately.

S&F Neoprene rubber beading of U or C section suitable for 5mm thick glass fixed along with edges of aluminium glass panes of joinery, all as directed by Engineer-in-charge.

S&F UPVC, double flat / groove type, roller for sliding windows all as directed by Engineer-in-charge. Note: Rollers shall conform to the samples kept with the Engineer-in-Charge.

S&F 100mm long powder coated Aluminium starlock for sliding window shutters conforming to the samples held in the office of Engineer-in-charge.

S&F 25mm dia Powder coated aluminium decorative type curtain rod complete all as specified and as directed. Note: colour of curtain rod shall be approved by Engineer-in-Charge.

S&F in repair 20mm dia Fancy type, Tubular towel rail, , brass CP, 60cm long between flanges complete all as specified and directed by Engr-in-Charge. Make:- CERA Cat Pat No-F5003102 or Equivalent

S&F Fancy type Soap dish, CP Brass Make: CERA Cat Pat No-F5003106 or Equivalent complete all as specified and directed by Engr-in-Charge.

S&F Aluminium grill with suitable aluminium anodised frame F/H section manufactured by M/s DECO GRILL as per design No DG-104, 100mm x 5.5mm to 6.5 mm thick with necessary channels and clips complete all as specified and as directed by Engr-in-Charge,

S&F 32 mm dia and 900mm long PVC waste pipe suitable for sink, WHB and urinal.

M&L Granules textured homogeneous wall finishing consisting of of a two component system of Dry Granules (25 Kgs per pack) made of 92% silica Particles coated with fade resisteant pigments, 100% acrylic polymer bonding agent (5 Kgs per pack) with the applied thickness of the coating between 0.8mm -1.2mm on a cured , smooth level plaster without keying, as per the shades/combinations approved, to be applied by and approved applicator of the manufacturer, as per the directions/supervision of the Engineer-in-Charge.The above textured coating should confirm to surface spread of flame class one of BS 476 : Part 7 : 1971 and pull off strength of the coating meet JISA 6909 on smooth plastered surface.

M&L 40 mm thick (measured solid) ready made reinforced precast cement concrete type B0 (1:2:4, 12.5 mm graded stone aggregate) louvres and jallies, set in CM 1:4, including all mouldings complete all as specified and as directed by Engr-in-Charge. Note : Contractors are advised to visit the samples held in the office, before submitting tender.

S & F Ready made ornamental Precast reinforced cement concrete type B0 1:2:4 (12.5 mm graded aggregate) designer pillars (Size- 100 x 100 x 900 mm) having groove on two faces, for fixing louvres and jallies, set in CM 1:4 on compound wall. all as approved and as directed by Engr-in-Charge. Note : The design of pillar, shall be got approved before bulk procurement . The tenderers are advised to visit the site for sample.

S&F Delinator twin reflector, made out of polycarbonate and toughened aluminium alloy body of size 300x170x65 mm made out of MS pipe of 51 mm dia and mounted on oval shaped metal plate of dimensions 302x167 mm fitted with two nos 110 mm dia high reflective reflectors on both sides, alongwith 2 Nos 70x23 rectangular reflectors each side for excellent reflectivity in the night hours. Make:- Dark Eye, 3M, Kiwalite of Kiwa chemical industry Co Ltd/Future vista or Aktion safety or equivalent as approved by GE.

S&F reflective road studs made out of tough polycarbonate and its reflective lance shall be made with polycarbonate microprismatic, retro reflective lance electronically welded to the body of stud and overall size 90mm x100mm x18 mm, the lower surface of studs will be supported with 2 Nos nylon shanks each of length not less than 20 mm and load bearing capacity 20 ton and fixed with epoxy adhesive in road complete all as per manufactures instructions. Make:-3M, Kiwalite of Kiwa chemical industry Co Ltd/Future vista or Aktion safety or equivalent as approved by GE.

S&F solar reflective road studs made out of tough polycarbonate made out of solar cells, LED, maintenance free lighting devices and its reflective lance shall be made with polycarbonate microprismatic, retro reflective lance electronically welded to the body of stud and overall size 113mm x90mm x25 mm, the lower surface of studs will be supported with 2 Nos nylon shanks each of length not less than 20 mm and load bearing capacity 20 ton and fixed with epoxy adhesive in road complete all as per manufactures instructions. Make:- Kiwalite of Kiwa chemical industry Co Ltd/Future vista 3M or Aktion safety or equivalent as approved by GE.

M&L Hot applied thermoplastic painting on road marking, arrows, square etc, thickness of thermoplast painting not less than 1mm thick complete all as specified and directed. Note :- Application of painting will be carried out by mechanical painting machine as specified.

S&F Convex mirror of size 800 mm dia of PVC material provided with suitable MS pipe post, having clear and definite mirror image with 130 degree of viewing including fixing in position in PCC.

S&F Heavy ABS plastic speed breaker of size 750x75x250 mm with two highly reflective reflectors moulded in PMMA material are welded with ABS plate through ultrasonic welding process and then fixed on the speed breaker. Speed breaker to be fixed with epoxy and hardener and bolts.

M&L Point wiring complete with 1.5 Sqmm single core PVC Insulated but unsheathed multistranded copper conductor FRLS cable 650/1100 Volt grade down through and including non metallic rigid PVC heavy duty concealed conduit, min 20mm external dia,heavy duty, but shall be increased to suitable size, as per requirement in accordance with clause 19.125 of SSR Part I, ISI marked, including conduit accessories like bends,tees,junction box etc fixed concealed/recessed in wall or ceiling etc including 1.5 Sqmm earth wire, single core PVC insulated but unsheathed multistranded copper conductor FRLS cable as earth continuity wire including sunken type pressed steel terminal boxes of suitable size with 2.8mm thick bakelite sheet white/coloured top cover Make Finolex/Havells/ NICCO/Anchor (a) One light controlled by one,one way 5 Amps SP switch Note: The cost of cutting/chasing in walls/floors/ceilings wherever required shall be deemed to be included in the quoted rate.

All as per item no 102 but (b) one fan/Exhaust fan point controlled by 1 one way switch

All as per item no 102 but (c) one 3 pin 6A socket outlet on same board

One 3 pin 6 Amp switch socket outlet on independent Board

M&L Point wiring complete with 2.5 Sqmm single core PVC Insulated but unsheathed multistranded copper conductor FRLS cable 650/1100 Volt grade down through and including non metallic rigid PVC heavy duty concealed conduit, min 20mm external dia,heavy duty, but shall be increased to suitable size, as per requirement in accordance with clause 19.125 of SSR Part I, ISI marked, including conduit accessories like bends,tees,junction box etc fixed concealed/recessed in wall or ceiling etc including 2.5 Sqmm earth wire, single core PVC insulated but unsheathed multistranded copper conductor FRLS cable as earth continuity wire including sunken type pressed steel terminal boxes of suitable size with 2.8mm thick bakelite sheet white/coloured top cover Make Finolex/Havells/ NICCO/Anchor (a) One 3 pin 15A socket outlet Note: The cost of cutting/chasing in walls/floors/ceilings wherever required shall be deemed to be included in the quoted rate.

S&F Switch piano flush button, 1 way, 6 Amps,240V (ISI marked).complete all as specified and as directed.

S&F Switch socket outlet, Multipurpose, 6 pin 16A, Flush type, controlled by one piano switch, 240V (ISI Marked) complete all as specified and as directed.

S&F Switch socket outlet, Multipurpose, 2 in 1, 5 pin 6A, Flush type, controlled by one piano switch, 240V (ISI Marked) complete all as specified and as directed.

S&F Ceiling rose, surface bakelite, 65x17mm, three terminals (ISI Marked) complete all as specified and as directed.

S&F Stepped type electronic fan regulator 120 watt, flush type complete all as specified and directed.

S&F 20W Surface/Wall mounted Batten LED Luminaire, extruded aluminium housing with PC diffuser and integrated electronic driver with high efficiency long life LED chips, CRI=80(Minimum) PF>0.95, System luminous efficiency >100 lm/Watt, Operating voltage 150V-270V including electrical connection with 3 Core flexible cable of appropriate size from ceiling rose to LED fitting complete all as specified and directed, fixed in repairs Make : Wipro Trim LED (LL20-281-XXX-65AL1/Philips (BN021C LED 20S PSU CW GR S2) or / Orient (LBLN-20-C-AL) Note: The contractor should submit LM79 and LM80 test certificates of the manufacturers for the batch of light fittings supplied.

Supply and fixing commerical LED luminarie 10 watt 1000 lumen input frequency 50/60 Hz system current in Amp. @240V AC 0.050 A Power Factor>0.90 THD <20% Built-in surge protection 3.5 KV including all accessories complete all as specified and as directed by EIC Make Bajaj Product Cat ref BCLSB 10 WH/Wipro/Philips

S&F rated ceiling fan 1200 sweep and connecting upto and including provision of 23/0.0076 (for equivalent size in mm) flexible 3 core 1.5Sqmm PVC insulated copper conductor cable from ceiling rose to fan complete all as specified and directed. Make: Orient (Crown)/CG(HS Plus), Havells(ES-50)/Usha (VETRA)

M&L Bore of 300mm Earthing complete with galvanised steel pipe electrode, 40mm bore, medium grade, 3 metres long, connected with earthing lead of size 25mm x 4mm dia galvanisedstrip to the earth test point 9upto 7.5m length) including earth work, returning, filling, fill compound to reduce soil sensitivity and high quality earth pit cover made of PCC all as specified and directed by Engr-in-Charge. Note:- The compound (earth enhance gel) to reduce soil resistivity should be suitable for the prevailing soil, IR value should be less than 5.0 Ohm. Excavation, earthwork returning and filling to be included in the quoted rate

S&F DB VTPN, 4 way, Double door, IP 43 prtection, with connected accessories like insulated bus bars, insulated neutral bars & earth bar, blanking plates,cable management kit complete and including following items. (a) Incoming MCCB four pole 63 Amp C series 10 KA-02 Nos (b) Outgoing MCB SP 6 to 32 Amp 10 KA C Series -08. Make : ABB/Schneider/Siemens.

S&F MCB DB SPN, 4way, Double door, IP 43, protection, with connected accessories like insulated busbars, insulated IP2X neutral bars & earth bar, blanking plates, cable management kit complete all as specified and directed.. Make: Legrand/Schneider/Siemens

S&F MCB SPN 40 Amps 'C' series 10KA ,240 Volt, 10 KAcomplete all as specified and directed.. Make: Legrand/Schneider/Siemens

S&F MCB SP 6 to 25 Amps 'C' series 10 KA 240 Volt, 10KA complete all as specified and directed.. Make: Legrand/Schneider/Siemens

M&L Point wiring complete with 1.5 sqmm single core PVC insulated but unsheathed copper conductor FRLS 1100 Volts grade cable, drawn through and including PVC concealed conduit heavy duty grade ISI marked 20 mm dia (external), including conduit accessories like bends, tees, junction boxes etc fixed concealed/recessed in wall or ceiling etc including 1.5 sqmm PVC insulated but unsheathed copper conductor FRLS cable as earth continuity wire including metal flush modular switch box with frame and cover plate for modular switches, sockets etc all as specified and directed by Engineer in Charge Note: Cost of cutting / chasing on wall and making good after repair shall be deemed to be included in quoted rate . Make of cable: Havells/ Finolex/ RR Kable/ KEI (a) One light point controlled by one switch.

All as per item no 119 but (b) One 3 pin socket outlet, 6 amps,on same board

All as per item no 119 ( c) One 3 pin socket outlet, 6 amps, independent,board.

M&L Point wiring complete with 2.5 sqmm single core PVC insulated but usheathed copper conductor FRLS 1100 Volts grade cable, drawn through and including PVC concealed conduit heavy duty grade ISI marked 20 mm dia (external), ISI Marked, including conduit accessories like bends, tees, junction boxes etc fixed concealed/recessed in wall or ceiling etc including 2.5 sqmm PVC insulated but unsheathed copper conductor FRLS cable as earth continuity wire for One 3 pin socket outlet. 15 amps,independent board including metal flush modular switch box with frame and cover plate for fixing of switches, sockets etc all as specified and directed by Engineer in Charge Note: Cost of cutting / chasing on wall and making good after repair shall be deemed to be included in quoted rate . Make of cable: Havells/ Finolex/ RR Kable/ KEI

S&F Modular switch 1 way, 6 Amps, 1 module (ISI Marked) complete all as specified and as directed by Engineer-in-Charge. Make: Legend (Arteour) / Schneider (zencelo) / hager (berker)

S&F Modular switch 1 way, 16 Amps, 1 module (ISI Marked) complete all as specified and as directed by Engineer-in-Charge. Make: Legend (Arteour) / Schneider (zencelo) / hager (berker)

S&F Modular socket, 6 Amps, 2/3 pin combined 2 module (ISI Marked)complete all as specified and as directed by Engineer-in-Charge. Make: Legend (Arteour) / Schneider (zencelo) / hager (berker)

S&F Modular socket, 6/16 Amps, 2/3 pin combined 2 module (ISI Marked) complete all as specified and as directed. Make: Legend (Arteour) / Schneider (zencelo) / hager (berker)

S&F Modular fan regulator, 120 watt, 2 modular (ISI marked) complete all as specified and as directed. Make: Legend (Arteour) / Schneider (zencelo) / hager (berker)

M&L Sub main wiring with two runs of 4.0 sqmm single core PVC insulated but unsheathed multistranded copper conductor FRLS 1100 Volts grade cable fire retardant low smoke drawn through and including PVC concealed conduit heavy duty grade ISI marked 25mm dia (external) but shall be increased as per actual site requirement in accordance with clause 19.125 of SSR part- I including conduit accessories like bends, tees, junction boxes etc including 4.0 sqmm PVC insulated but unsheathed multistranded copper conductor FRLS cable as earth continuity wire fixed complete all as specified and directed. Note: Cost of cutting / chasing on wall and making good after repair shall be deemed to be included in quoted rate . Make of cable: Havells/ Finolex/ RR Kable/ KEI

M&L Earthing complete with excavation and earth work in any type of soil with galvanized steel earth plate electrode size 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtrs below ground level) with top edge of the earth plate not less than 1.5 mtr below normal ground level connected to GI earth strip 32 x 6 mm by means of bolts nuts check nuts and washers of galvanized iron, all as shown in electrical plate No.3 of MES SSR Part-1 connected to main switch board or main control board all as specified and testing on completion including provision of earth strip protected by galvanised iron 40 mm dia bore light grade pipe and watering pipe shall be 20 mm bore medium grade, PCC pit with pre cast RCC cover, charcoal / salt funnel etc. complete all as directed. NOTE : (1) The conctrete pit shall be PCC 1:3:6 tye C -1, 40 mm thick pre cast cover slab of RCC (1:2:4) type B-1 using 20 mm graded stone aggregate reinforced with 8 mm TMT bars with suitable cast iron handle shall be provided (ii) Item includes the cost of 7.5 m GI pipe for protection of earth strip (iii) Item includes the cost of 7.5 mtr length earth strip 32 x 6 mm (iv) Result of earthing is not less than 2 Ohm

S&F 300mm sweep Exhaust fan 240 V AC,heavy duty industrial type,metal body fixed as per manufacturers instruction, connecting with and including 2 corex0.5 Sqmm copper coduct PVC insulated and PVC sheathed three core cable complete. Make: CG,Havells(Ventil Air), Bajaj (Bahar)/ ORIENT (HILL AIR )/USHA (AERO)

S & F 35 Watt LED street light luminaire, spun housing, aluminium/ die cast grey finish power coated body, clear arcylic cover, rated Voltage 240 Volt ,50 HZ, operating voltage Range 120-270 Volt , nominal lumen efficiency 120 lm/watt, IP-65 Prtotection with mounting clamps, bolts and nuts, fixed to vintage type bracket as specified with pole complete all as specified and as directed Make: Wipro skyline + LR06 cat Ref No LR06-501-XXX-57-XX/Philips BRP 042 LED/Crompton LSTS-36-CDL-M

Supply and lay 25mm dia 3-layer PP-R Polypropylene random co-polymer) pipes SDR 7.4 &SDR 11, UV stabilised and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings laid in trenches/fixed to wall or as site requirement, including fittings Make: SFMC / VECTUS / RELIANCE / AFG / SFC

Supply and lay 50mm dia 3-layer PP-R Polypropylene random co-polymer) pipes SDR 7.4 &SDR 11, UV stabilised and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings laid in trenches/fixed to wall or as site requirement, including fittings Make: SFMC / VECTUS / RELIANCE / AFG / SFC

S &F PP-R Gate valves (Brass Insert) of 25mm bore

S &F PP-R Gate valves (Brass Insert) of 50mm bore

M&L Construction of valve chambers size 750 mm x 750 mm x 450 mm (internal dimensions), incl earth work, with PCC foundation in the ratio 1:4:8 stone masonary 200mm thick in cement mortar in the ratio 1:4, plastering 15 mm thick in the ratio of 1:4 incl MS sheet cover 3mm thick with angle iron frame 25 x 25 x 4 mm size, locking arrangement complete with painting on steel surfaces with two coats of synthetic enamel paint over a coat of red oxide primer all as specified and as directed

Making connection of PP-R distribution brach with PP-R man of 50 mm dia sizes by provding and fixing tee including cutting and making fusion joint etc.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized iron strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 2core complete all as specified and as directed Make Havells/RR Cables/Polycab

Supply and lay double wall corrugated (DWC) high density polythene pipes having corrugation on the outer wall and plain surface on the inner wall confirming to IS 16205 & IS14930 ( Part I and II) for protection of underground calbes of size 50 mm outer dia with all fittings. laid in trenches / road/ nallah or fixed along wall. poles or laid under floor (including cutting floor/Road and making good to match with existing adjoining surface etc for cable protection all as specified (excavation and earth work shall be measured and paid separately) Make: Rex/Poly/Gemini

Supply, install and test Split air conditioner, inverter type electric driven, single phase, of capacity 2 ton 3 star rated with copper condenser, indoor noise level < 50 db with standard fitment and outdoor unit fixed on wall mounted type bracket and connected to power supply all as specified and directed. Make : Voltas Model No 24H SZS 2 ton/Carrier Model No imperial NXi CA 124EN3R30FO/Hitachi Merai 3100S 2.0 TR-RMNG322HCEA Add Note (i) wall bracket for outdoor unit and top plug for indoor unit is deemed to be included in unit rate.

S&F Modular type power units with starter 25 A , DP MCB & 25 Amp plug top .complete all as specified and as directed. Make: C&S/Legrand/ABB

Removing building materials etc to a distance exc 1.0 km but n.exc 1.50 km, including laiding, unloading and stacking at the destination.

Bharat Enterprise

Vijay Construction Co

shivshakticonstruction

KRISHNA ENGINEERING

K K Construction Co

SURAJ ENTERPRISE

badri glass and construction