DEPOSIT-Kozhikode Corporation-DEPOSIT WORK-Reformation of Ezhunnamannil thodu and reconstruction of flood control bund on the left bank of Poonoor puzha at Chelavoor in Kozhikode Corporation-General Civil Work

Amount

Civil Works

15.7.4:Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In cement mortar

2.6.1:Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil

60.7.2:DR PACKING Under foundation - Dry stone packing under foundation with good quality blasted rubble including conveyance of material and labour charges etc. complete as per direction of departmental officers at site.

4.1.8:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

4.1.5:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

5.1.2:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

4.3.1:Centering and shuttering including strutting, propping etc. and removal of form work for:Foundations, footings, bases for columns

5.9.6:Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.9.5:Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

60.7.4:DR PACKING FOR APRONS - Rough stone dry packing for apron with good quality blasted rubble including packing to compactness to lines levels, cost and conveyance of all materials labour charges etc. complete as per direction of Departmental officers at site

Supply , Fabrication of MS and SS material for Embedded parts

OD34970/2024-2025:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

OD34968/2024-2025:Supply of MS round bar including cost of conveyance charges

OD34969/2024-2025:Fabrication and erection of Embedded parts for canal shutter (up to 2 tones w.t) and accessories as per approved specifications and drawing and directions of departmental officer at site including cost of labour, machinary , all leads and lifts ,incidental and handling charges etc. complete but excluding cost of material already supplied

OD34971/2024-2025:Fabrication supply erection and assembling in correct position and alignment by welding SS embedded parts in 304L Grade like roller track seal track seal seat etc. as per approved specification drawing and direction of departmental officer at site including cost of all materials , labour machinery for planning welding shearing grinding etc. lead and lift conveyance incidental and handling etc. complete

Supply of materials, fabrication, painting and erection of MS shutters

OD34987/2024-2025:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

OD34985/2024-2025:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

OD34982/2024-2025:Supply of MS round bar including cost of conveyance charges

OD34983/2024-2025:Supply of MS Bolts and Nuts

OD34984/2024-2025:Fabrication and supply of Structural steel canal shutter(up to 2 tonnes w.t) / Hoist bridge /platform and accessories etc. for the same as per approved specifications, drawings and directions of dept officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc. complete but excluding cost of material already supplied

85.114:Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

OD34986/2024-2025: Erection of the Canal shutter (Up to 2 tonnes weight)/Hoist Bridge / Platform including handrail,l adder etc. same including. Alignment correcting and setting complete including cost of all machinery, labour all incidental and conveyance ,lead and lift charges etc. complete but excluding cost of material already supplied

Supplying and fixing of flat type rubber seal at the bottom side , angular type at vertical side of the shutter

85.116:Supplying and fixing in correct position with specified initial interface the flat type rubber seal confirming to IS 11855 to the gates including cost of SS bolts and nut all labour and machinery and incidental and conveyance charges complete as per approved specification and drawing

85.117:Supplying and fixing in correct position with specified initial interface the Angular type rubber seal confirming to IS11855 to the gates including cost of SS bolts and nuts and all labour and machinery and incidental and conveyance charges complete as per approved specifications and drawings

85.118:Supplying and fixing in correct position with specified initial interface L-type / bulb nose rubber seal confirming to IS11855 to the gates including cost of SS bolts and nuts and all labour and machinery and incidental and conveyance charges complete as per approved specifications and drawings

Supplying and fixing Cast steel thrust roller

OD34988/2024-2025:Supplying and fixing cast steel thrust roller assembly having 125mm Dia, 50mm tread width, SS(304) shaft and accessories as per approved specifications and drawings including cost of all materials, machineries, labour , all lift and lead, incidental and conveyance charges etc. complete

Supply of materials, fabrication, painting , Providing Screw rod with Worm reducer Unit erection of hoisting bridge and hoist units for shutter

OD34973/2024-2025:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

OD34972/2024-2025:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

OD34976/2024-2025:Supply of MS checquered plates including cost of conveyance charges

OD34979/2024-2025:Supply of MS Bolts and Nuts

OD34978/2024-2025:Supply of 32 mm NB GI pipe

OD34980/2024-2025:Fabrication and supply of Structural steel canal shutter(up to 2 tonnes w.t) / Hoist bridge /platform and accessories etc. for the same as per approved specifications, drawings and directions of dept officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc. complete but excluding cost of material already supplied

OD34981/2024-2025:Providing of worm and pinion having a lifting speed of around 5.00 cm/min for hand operation /manual operation including cost of all materials, labour ,hire charges and conveyance

OD34975/2024-2025:Providing EN-8 screw rod 7.5 tonne capacity 4.00M lift screw hoist having one number of EN-8 Screw shaft having a lifting speed of around 5.00 cm/min for 24rpmof hand operation including cost of all material, labour, hire charges and conveyance

OD34974/2024-2025: Erection of the Canal shutter (Up to 2 tonnes weight)/Hoist Bridge / Platform including handrail,l adder etc. same including. Alignment correcting and setting complete including cost of all machinery, labour all incidental and conveyance ,lead and lift charges etc. complete but excluding cost of material already supplied

85.114:Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

OD34977/2024-2025:Trial Run of Shutter

Haneefa (BID ID -2182737)

Bidder Name

Haneefa

Nellikkaparamba Labour Contract Co-operative Society Ltd No D 3188