Construction of new Maternity Block at Taluk Headquarters Hospital Tirurangadi Malappuram District- SITC of Fire Fighting Arrangement

Amount

DIESEL ENGINE DRIVEN PUMP:-Supply, installation, testing and commissioning of main diesel engine driven horizontal mounted centrifugal pump, end suction type suitable for automatic operation rated for 30HP, 1620 LPM at 50 MWC high efficiency volute type with cast iron casing, bronze impeller pump coupled to a diesel engine at 1800/1500 RPM vibration damping arrangements, diesel tank with semi rotary pump, Battery, coolant, lubricating oil, exhaust piping, necessary controls such as pressure switch and interconnecting cable from control panel to battery etc.

MOTOR DRIVEN PUMP:-Supply, installation, testing and commissioning of horizontal mounted end suction electric motor driven pump suitable for automatic operation rated for 1620 LPM at 50 MWC high efficiency volute type with cast iron casing bronze impeller, pump coppled to SPDP squirrel cage induction motor 22KW /30 HP, 415V, Three phase 50 Hz. the pump set is foot mounted type including all accessories such as standared coupling, guard, common base frame pad/foundation bolts etc. complete.

Supply,installation,testing and commissioning of Horizontal mounted end suction type electric motor driven two stage Jockey pump 180 LPM at 50 MWC h with cast iron casing bronze impeller,including all accessories operating on Three phase 50Hz,415V AC supply including foundation,bolts etc.complete. The pump set shall be of 3.73KW / 5 HP

Control Panel

Fabrication, supply, conveyance, installation testing and commissioning of floor or wall mounting, dust and vermin proof, cubicle type MV panel board comprising of the following components/ devices & complying to IS 8623.

Fabrication of fully partitioned, dust and vermin proof enclosure for panel assembly as per form 4 of IS 8623 (with latest amendments) using 1.60 mm CRCA sheet as per approved design and requirement, with front and rear access facility, bus bar chambers, hinged doors for all switch gear compartments, earthing the doors using 4 sq mm braided copper conductor, providing necessary cutouts for mounting meters, relays, indication lamps, bus bar interconnection etc, detachable covers for bus bar chamber and cable alley, powder coating the assembly after subjecting to 7 tank process etc as required. CRCA sheet alone be used for the fabrication. Angles/ flats/ slotted angles etc shall not be used for the fabrication of panel assembly. The measurments should be taken the area of the complete sheets used for panel board including partitions, folding, shrouding etc. including control wiring

Supply and providing the following size of SMC sheets in the panel as barriers & shrouding using required bolts and nuts including cutting to shape etc., as required.

2mm thick

Supply and fixing the following types of beeding along the periphery of doors/ other detachable compartments to make the panel assembly dust & vermin proof including sticking with glue

A' section neoprene beeding suitable for 1.60/ 2.00 mm sheet

Fabrication, supply, conveyance and installation of base frame for floor mounting type panel board using channel of class designation ISMC 75 including cutting, welding, drilling holes, painting with two coats of synthetic enamel paint over a coat of zinc chromate primer, bolting the frame to the panel and to the finished floor using required bolt and nuts, making good the damages etc. as required

Fabrication, supply & fixing main bus bar system and interconnections with electrolytic grade copper strips/ rigid conductors conforming to IS 1867 (with latest amendments) for bus bar arrangement with single strip per phase supported on finger type bus bar supports of adequate size, spacing between supports not exceeding 50 cm & overhang not exceeding 5 cm including bending to shape, drilling holes, tinning the points of contacts, fixing heat shrinkable PVC sleeves, plated bolts and nuts with plate washers and spring washers, copper sockets for round conductors, etc., as required

Fabrication, supply & fixing earth bus system with copper strip/ conductor and connecting all accessories as per rule including g tinning the points of contacts etc as required

S & F switch disconnector unit (isolator) complete with handle assembly, door inter lock and padlocking arrangement of the following ratings:

125 A, TP/TPN AC 23 A duty

100 A, TP/TPN AC 23 A duty

63A, TP/TPN AC 23 A duty

Supply and fixing Three Phase DOL Starter suitable for upto 5HP pumpmotor and fixing in the existing starter board and giving connection

Supply and fixing Three Phase DOL Starter suitable for upto 30HP pumpmotor and fixing in the existing starter board and giving connection

Supply and installation of the following accessories suitable for 50 Hz AC supply conforming to IS 8828- 1995/ IEC 60898 of the following current ratings in the existing enclosure and giving connections as required

0.50 A to 4 A, 10 kA, SP MCB (C curve)

INDICATION LAMPS AND LEGEND PLATES

Aluminium anodised Danger Notice Board of size 150 x 100 mm. with inscriptions ( both in English and Malayalam) and conventional Skull and Bone in Red colour.

LED indicators for all voltage ranges - Red, Green, Black, Yellow or Orange Colour

LED indicators for all voltage ranges - Blue Colour

Mini power contactors

9 A, 3 pole, AC 3 rated mini power contactor with 1 NO + 1 NC auxiliary contacts & with AC coil

CURRENT TRANSFORMER

150/ 5 A, 5 VA, resin cast metering CT of accuracy class 0.5

Multifunction meters

Three phase multifunction meters to read V, A and F, accuracy class 0.5

Supply and wiring with 650/1100 V grade PVC insulated stranded single core copper conductor cables conforming to IS 694 part I 1990 for interconnecting the control devices/ equipments including providing suitable size sockets at the termination points, keeping the wiring firm by suitable tie/ tie mounts/ PVC duct etc as required.

1.50 sq mm single run with required sockets & numbering ferrule.

2.50 sq mm single run with required sockets & numbering ferrule.

4.00 sq mm single run without sockets.

Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.

3 core 4 sq mm with factory made clamp

3 core 25 sq mm with factory made clamp

Supplying siemens / tropodur type nickel plated single compression brass cable gland for PVC insulated and PVC sheathed armoured aluminium/ copper conductor cable 1.1 KV grade, and making end termination suitable for 2/ 3/ 3½/ 4 core cable of the following sizes as required.

Supplying and providing earth clamps for siemens/ tropodur type cable glands of suitable length and other dimensions noted along with each size of glands for the following sizes of cables as required.

4 sq mm with 12 mm wide x 1 mm thick clip

25 sq mm with 20 mm wide x 1.20 mm thick clip

Supply of superior quality aluminium tubular cable socket and making core termination of cables of the following sizes including crimping etc. as required.

Supply,installing,testing and commissioning or Air cusion vessel made of mild steel of 250mm dia with automatic air release cock,25mm dia drain valve and shutt off. The vessel shall be 120 cm in height etc.complete

Supply,installation,testing and commissioning of Pressure Guage

Suppy,installation,testing and commissioning of pressure switch for automatic operation. Make Indfoss

Supplying and fixing of Priming tank of size not less than 500 liters of storage capacity as required etc.

Under/Above Ground Piping:- Supply, errection,testing and commissioning of M.S 'C' class pipes confirming to IS:1239 part I with malleable specials confirming to IS.1239 part.II, such as elbows, reducers, flanges etc.including cutting,welding,fixing in/on walls/ceiling by suitable,supports. The pipe shall be apinted with one coat of primer and two coats of synthetic enamel paint of approved colur/shade.

150mm dia

100mm dia

80mm dia

65 mm dia

50 mm dia

40 mm dia

32 mm dia

25mm dia.

Supply,installation,testing and commissioning of instanceous pattern Gun metal single Headed Hydrant valve bearing to IS:5290,63mm lblique type with instantaneous hose coupling adaptor, complete with PVC blank cap

Supply and providing Hose Cabinet

Supply and place in position of Controlled Percolated Hose conforming to IS 623,63mm 15 Mts.Long ,with male and female instantaneous gunmetal coupling

Supply,installation,testing and commissioning of Hydraulic, Hose Reel drum completed with swinging type drum with 19mm dia Rubber braided hose of 30M length and Shunt off nozzle, with necessary fittings etc.complete

Supply and place in position of Gunmetal Branch pipe with 63mm female instanceous inlet, male,threaded outlet,complete with hexagonal base nozzle conforming to IS:903 with ISI mark.

Supplying,installing,testing and commissioning CI Butterfly valve slim seal standard lever operated, wafer type, SG iron coated with nylon Disk, SS shaft,Nitrile Body linning . PN 16 rating.Design as per BS 51 confirming IS 13039 with required flanges nuts, bolts.

150mm dia

100 mmdia

80mm dia.

Supply,installation, testing and commissioning of C.I. slim seal type Non return valve with required flanges, nuts and boltsw gasket etc. complete

150mm dia

100 mm dia

80mm dia.

Supply and installation of the following sizes of cast iron Foot valve with strainer to the pump sets complete with bolts,nut gaskets if any as required etc.

150 mm Dia

100mm dia.

Supplying, installing,testing and commissioning of Cast Iron Ball Valves with fittings of screwed end type

25mm Dia

Supply,installation,testing and commissioning of single acting Air Release Valve with screwed inlet 25mm dia etc.

Supply,installation,testing and commissioning of Fire Brigade inlet connection with 4 Nos. of 63 mm dia built in Gun metal Non-retun valves instantaneous coupling type arranged on 100 mm dia etc. Pipe manifold shall be connected to wet riser main.

Supply and providing pressure guage

Supply and providing pressure switch

Supply,installation,testing and commissioning of approved make 15mm brass sprinkler heads designed to operate at 68 deg.. Celcious etc. with necessary fitting etc.complete.

Pendent type

Side wall type.

Supply and providing air cushion vesse;

Supplying installating testing and commissioning flow switch on sprinkler distribution header on each floor and shall be connected to fire alam panel

Fire Detection & Alarm System

Supplying,installing,testing and commissioning of microprocessor based main fire alarm control panel of 8 zones capacity with visual LED indications for fire/fault alarms, signals and should have stage alaram facility with maintenance free battery back up for 24 hours normal operation and 15 minute alarm operation. The panel shall be fabricated by MS sheet and powder coated both inside and out side door shall be glass fronted type with locking arrangement as per specification.

Supplying,installing,testing and commissioning of optical type smoke detectors with solid stage design, indicating lamp, mounting base etc.

Supplying,installing,testing and commissioning of heat detectors with solid stage design, indicating lamp, mounting base etc.

Supplying,installing,testing and commissioning of Manual call point break glass type as per standard specification.

Supplying,installing,testing and commissioning of Electronic dual tone Hooter(sounder) as per standard specification.

Supplying and laying of PVC conduit with all necessary fittings. Etc.

20 mm dia

Supplying and laying of 1 sq.mm cross section PVC insulated copper wires.

Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages, colour washing etc. as required.

2 core 1.50 sq mm using factory made saddles

Fire Extinguishers

Supplying and fixing of Dry chemical powder type fire extinguisher of 5 kg.s. capacity, with intial filling in brand new Cylinder with power coated finish fitted with Gun metal union, discharge hose, wall mounting bracket etc.complete confirming to IS.2171

Supply, Installation, Testing and Commissioning of solid state Amplifier of 60W RMS out put in rack, including necessory control wires, jacks etc. complete as required

Supply & erecion of MICROPHONE for Intelligible, crisp and bright sound suitable for all type of PA applications. Supplied with quick detachable holder with 3-pin professional XLR connector & 6 mtrs. Twin core shielded low noise cable.

Supply, erection, testing and commissioning of 6 Watt Wall mounted type Speaker for PA System.

Supply, erection, testing and commissioning of Talk back field device .

Suply and providing emergency fire escape lighting system consisting 2 nos lamp ,7 AH FMF battary charging unit ,exit sign display etc in MS enclosure

Supply, erection, testing and commissioning of Coaxial RG 6 PVC iunsulated Cable as per BIS standard

AUTO GLOW SIGNAGES (OPTIONAL)

Supply & erection of Glow Sign Boardmade of 3mm thick PVC foam board for each floor 12" x 4" (appropriate places)

Supply & erection of Assembly Point sign board 16" x 16"

Supply & erection of Fire Escape rout in each floor having size 12" x 16" made of 3mm thisk acrylic sheet with glass frame

Charges for preparation of Fire Drawing per A3 sheet first copy

Copying charges for additional copies per A3 sheet