General

Engaging of Shovel 0.85 cum 110 hp / Hydraulic Excavator for site cleaning by lifting of old Garbage from road level to Natural Ground level for Foundation at Proposed C&D plant site.

Engaging of Tipper 5 / 5.5 cum for site cleaning by lifting of old Garbage from road level to Natural Ground level for Foundation at Proposed C&D plant site.

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material as per Technical Specification 305 MORD / 304 MORTH for Mechanical Means.

Supply and Filling with Sand Filling complying with standard specifications including cost and conveyance of dust to site of work labour charges watering tamping, ramming etc complete and as directed by the Engineer-in-Charge of the work

Providing Plain Cement Concrete nominal mix (1:4:8) in open foundations using 40 mm nominal size Graded hard stone aggregate, mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days complete as per drawings and technical specifications. etc., complete and as directed by Engineer in Charge of work.

Supplying, Fitting and Placing Fe-500 HYSD Bar reinforcement in foundation complete as per drawings and technical specifications for Bars below 36 mm dia including over laps and wastage, Cost of binding wire and its fabrication charges, placing in position tying grills and cuttings etc., complete

Supply and delivery of Bolt and Nuts with Double washers including cost and conveyanace etc,complete But Exclusing taxes,(1"25mm) (MAT-08262)

RCC M- 20 Nominal mix (Cement:fine aggregate: coarse aggregate) corresponding to Table 9 of IS 456 using 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work, but excluding centering, shuttering. etc., complete.

Construction and Demolition Waste Recyling Plant-15-20 TPD 9a .FEEDER HOPPER: For Raw material Loading By Hydraulic Vehicle or Other Vehicles. Sepecification: Capacity: units 5.0 to 6.0 Cum, Lenghth:2.50m, Width: 2.50m, Height:1.0m From tapered portion of the hopper, Materail: MS Structural Members and MS Sheets.(Heavy-duty Mild Steel (MS) is standard, often utilizing high-strength wear-resistant steel (e.g., HB450) liners to handle hard rock, ore, and concrete.) Overall Height From Ground level: 6.50m to 8.0m, Including all accessories includind One Coat metal Primaer and 2 Coats of Enamel Paint, Exept Civil Work. 9b. FEEDER: Type: Grizzly, Capacity: 10 - 15 MTph, Maximum Feed Size: Up to 300mm, Motor Power: 5HP, Dimensions (Width): 900mm - 1800 mm, Frame with ISMC and top and bottpm sheets 4mm and 6mm Ms Sheets, Width Matching: The feeder width should match the crusher's feed opening (within 6 inches) to prevent overloading. Including all accessories includind One Coat metal Primaer and 2 Coats of Enamel Paint, Exept Civil Work.

9c.Single Toggle JAW Crusher: SIZE: 24"X12" (Feed Opening: Width:610mm,Gap:305mm), FRAME Consists of Fully bolted dowelled 4 piecs structure. front and rare frames are cast with heigh strength steel, and side plates are machined structural plates. JAWS: Reversible heigh quality graded manganese steel alloy jaws, the back faces of jaws machined for proper seating and firm support.Main Shaft: Constructed from high-grade forged steel (often EN-8 or EN-9 series) with diameter range of 100mm to 120mmalloy steel forged, Heat treated precision machined with heigh quality surface fininishing.Bearings: Fag or SKF Heavy duty self aligning double row bearings on swing jaw and main frame.Jaw Plates: Reversible manganese steel plates on machined seats.Toggle System: Includes a single toggle plate acting as a safety element.Adjustment: Often utilize hydraulic-aided or shim-based adjustment for the closed-side setting. Weight: Highly variable, ranging from ~3.4 to 4.0Metric tons (small). Drive: Pully With Belts, Power Requirement: Ranges from 22 kW (30 HP ). Maximum Feed Size: 350mm jaw opening might accept 300mm material) Capacity: 15 to 20 TPD, including all accessories includind One Coat metal Primaer and 2 Coats of Enamel Paint, Exept Civil Work.

9d. Crushed Material Conveyor: From Crusher to Vibrator screener: Sepecification: BELT: Belt Lemght: 12m / 40', Belt width: 600mm, Belt Thickness:8mm, Belt Play: 3 Play, Make: Hindustan/Bando/ (An ISO-certified firm producing industrial-grade rubber conveyor belts). Structure: Side Frames and Vertical Legs: ISMC:75X40X4.4mm, 12m length and vertical supports at a span of 3.0 to 3.50m Based on Site condition.MAKES: JSW,VIZAG,SAIL,TATA.Rollers: Conveyor idler rollers 76mm 3sets at 1.0m interval center to centre and bottom return conveyor 60mm dia and 800mm length.Pillowblocks: 4No's Consists of a cast iron housing and a SKF-211 insert bearing, Suitability: Suitable for constant and alternating rotation, Lubrication: Pre-lubricated and sealed for easy installation.Drums: 2 No's 220mm dia and 800mm length with rubber encasing. Conveyor Drive: Motor Power: 5 HP (3.7 kW, Motor Type: 3-Phase AC Induction Motor (Squirrel Cage),Voltage: 415 V ± 10% (Standard Industrial), Efficiency: IE2 (Energy Efficient), Mounting: Foot Mounted. Protection: IP55 or IP54 (Dust/Waterproof for industrial environments). Makes: Crompton,Havells,ABB,Kirloskar,CG. Gearbox Type: Vertical Worm, Gear Ratio:anges typically from around 20:1 achieve desired conveyor speed. Output Speed (RPM): Typically 20 to 25 RPM. Including all accessories includind One Coat metal Primaer and 2 Coats of Enamel Paint, Exept Civil Work. Any ISO certified Makes:

9e.Vibrating Screener: Screen Box/Basket: Capacity: Ranges 15 to 20 TPD, Screene Size: 3m X 1.20m (10'x4') The rigid structure housing the four decks, often designed with heavy-duty steel side plates, welded beams, and abrasion-resistant liners. Screening Media (3 Decks): Above 12mm to 20mm, above 6mm to below 12mm, Below 6mm to 0.0mm, screening surfaces, which can be perforated plates of 8mm thickenss. Vibrating Unit/Exciter: A single or dual-shaft mechanism with eccentric weights that generates a circular vibration motion. Suspension System: Springs (coil) that support the screen box and isolate vibrations from the main structure.Motor and Drive: A vertically or horizontally mounted electric motor 7.5kW (10 HP) that drives the shaft. RPM (Frequency): 850 - 1000 RPM.

8f. Conveyors for Screning material: 3 No's for type of Materils (12mm to 20mm, 6mm to below 12mm. Below 6mm to 0mm) BELT: Belt Lenght: 10.0m /33', Belt width: 500mm, Belt Thickness:8mm, Belt Play: 3 Play, Make: Hindustan/Bando/ (An ISO-certified firm producing industrial-grade rubber conveyor belts). Structure: Side Frames and Vertical Legs: ISMC:75X40X4.4mm, 10.0m length and vertical supports at a span of 3.0 to 3.50m Based on Site condition.MAKES: JSW,VIZAG,SAIL,TATA.Rollers: Conveyor idler rollers 76mm 3sets at 1.0m interval center to centre and bottom return conveyor 60mm dia and 500mm length.Pillowblocks: 4No's Consists of a cast iron housing and a SKF-211 insert bearing, Suitability: Suitable for constant and alternating rotation, Lubrication: Pre-lubricated and sealed for easy installation.Drums: 2 No's 220mm dia and 500mm length without rubber encasing. Conveyor Drive: Motor Power: 3 HP (2.25 kW, Motor Type: 3-Phase AC Induction Motor (Squirrel Cage),Voltage: 415 V ± 10% (Standard Industrial), Efficiency: IE2 (Energy Efficient), Mounting: Foot Mounted. Protection: IP55 or IP54 (Dust/Waterproof for industrial environments). Makes: Crompton,Havells,ABB,Kirloskar,CG. Gearbox Type: Vertical Worm, Gear Ratio:anges typically from around 20:1 achieve desired conveyor speed. Output Speed (RPM): Typically 20 to 25 RPM, Including all accessories includind One Coat metal Primaer and 2 Coats of Enamel Paint, Exept Civil Work, Any ISO certified Makes:

9g. Retuern Conveyor for Over size Material: From VIbrator screen to Crusher: BELT: Belt Lenght: 10.0 to 12.0m /33' to 40', Belt width: 500mm, Belt Thickness:8mm, Belt Play: 3 Play, Make: Hindustan/Bando/ (An ISO-certified firm producing industrial-grade rubber conveyor belts). Structure: Side Frames and Vertical Legs: ISMC:75X40X4.4mm, 10.0m length and vertical supports at a span of 3.0 to 3.50m Based on Site condition.MAKES: JSW,VIZAG,SAIL,TATA. Rollers: Conveyor idler rollers 76mm 3sets at 1.0m interval center to centre and bottom return conveyor 60mm dia and 500mm length. Pillowblocks: 4No's Consists of a cast iron housing and a SKF-211 insert bearing, Suitability: Suitable for constant and alternating rotation, Lubrication: Pre-lubricated and sealed for easy installation.Drums: 2 No's 220mm dia and 500mm length without rubber encasing. Conveyor Drive: Motor Power: 3 HP (2.25 kW, Motor Type: 3-Phase AC Induction Motor (Squirrel Cage),Voltage: 415 V ± 10% (Standard Industrial), Efficiency: IE2 (Energy Efficient), Mounting: Foot Mounted. Protection: IP55 or IP54 (Dust/Waterproof for industrial environments). Makes: Crompton,Havells,ABB,Kirloskar,CG. Gearbox Type: Vertical Worm, Gear Ratio:anges typically from around 20:1 achieve desired conveyor speed. Output Speed (RPM): Typically 20 to 25 RPM, Including all accessories includind One Coat metal Primaer and 2 Coats of Enamel Paint, Exept Civil Work, Any ISO certified Makes:

9h.Control Pannel: Fabrication ,transportation and and supply of Floor mounted control panel board with suitable size made of 18 SWG CRCA sheet steel enclosure, 14 SWG mounting plate for cable entry fabricated , painted with two coats of Red oxide primer and two coats of Grey paint, lock and key arrangements two side louvres with weld mesh inside etc., complete consisting of the following equipment with all internal wiring using LAURITZ KNUDSEN (FORMERLY L&T) / Finolex copper FRLS cables of suitable size and capacity and cable clamp etc complete for 3 phase motor sets. Total Connected Load: ~80 HP (~60 kW) (60 HP +20 HP for Future extension Load), Operating Voltage: 415V AC ± 10%, 3-Phase, 50Hz, IP55 protection, Main Breaker: 160A or 200A TPN MCCB (Moulded Case Circuit Breaker) with Shunt Trip,Busbar: Aluminum Busbar rated for 150-200A (suit 80HP + margin). Motor Starters (DOL/SD): Crusher (30HP): Star-Delta Starter (Automatic with timer), Screen (10HP): DOL Starter, Feeder (5HP): DOL Starter, Conveyors (5 x 3HP): DOL Starter. Protection Components: Individual Motor Protection Circuit Breakers (MPCBs) for each motor. Phase Failure Relay (PFR) / Single Phasing Preventer. Overload Relays (OLR) for all motors. Surge Protection Device (SPD). Control Logic & Safety: Sequence Start-Stop (Crusher -> Screens -> Feeders) to prevent clogging. Emergency Stop Buttons (Multiple, wired in series). Interlocking between Conveyor-Screen-Crusher (If one stops, all upstream stop).Instrumentation & Controls: Ammeter and Voltmeter with Selector Switches for each phase. Start/Stop Push Buttons, Indicating Lights (Running, Trip, Power On). Cable Entry: Bottom or Top with Gland Plate. Note: A 4-pole or 3-pole MCCB should be chosen based on the total load plus at least 25% for starting surge currents, typically around 160A-200A. Makes: Lauritz Knudsen (formerly L&T)- D shine / Schneider-NS NSX/Legrand -DP X3/ Siemens-3VL /Hager-h3/C&S -Winbreak2Makes of Meters : Schneider (Conzerve) / Lauritz Knudsen (formerly L&T) /Elmeasure / Siemens.

Supply, delivery, installation, and trial run of the complete setup of the C&D Processing Plant as per the above specifications, including proper signage for each item and water suppression arrangements.

Supply and transportation of following XLPE insulated, 1100V grade armoured aluminum UG cable with 3.5 core 95 sqmm as per specification confirming to IS:7098 (Part - I)./1554-I, Makes: As per list of recommended brands as category I.Torent / Universal / Unicab / Havells / Finecab / KEI / Gloster/ Polycab /RR Kabel/ Fortune Arrt /KEC Asian Cables/Orbit/Avocab /Gemscab /Batra Henlay.

Providing, laying spreading and compacting local (Gravel) material in block or large discrete particles, such as kankar, Literate, Dhandla etc. as per Table 400.13 specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, watering and compacting to the required density as per Clause 405.3 and Technical Specification Clause 408 MORD.