CONSTRUCTION OF SINGLE COMPOSITE LAB OF 7 X 10.60 MTRS IN THE EXISTING KV AT PALAMPUR MIL STN

Amount

Surface excavation not exc 3cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed.

Excavation in trenches,nexc 1.50m wide and n exc 1.50m in depth for foundation,etc or for shafts,wells,cesspits,manholes,pier holes,etc n exc 10 sq m on plan and getting out any type of soil complete all as specified and directed.

M&L PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

Formwork to sides of rough finished flat surfaces sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (in any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed.

M&L formwork to sides of fair finished surfaces square/rectangular surface of concrete pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

M&L formwork to sides of fair finished surfaces of concrete sides and soffits of or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc also splays between floors and beams etc complete all as specified and directed.

Form work to rough finished surfaces of concrete for soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

S&F mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F mild steel TMT bars 5 mm dia and over up to 10 mm dia in stirrups,spacers and binders and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L brick work with sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in Cement mortar 1:6, complete all as specified and directed.

Rendering 10mm thick on brick or concrete surfaces in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed.

M&L rendering 15mm thick in two coats i.e. 10mm thick in CM 1:6 and 5mm thick in CM 1:4 using water proofing liquid compound as per manufacturer's instructions on other than fair faces brick or concrete surfaces and finishing surfaces even & smooth without using extra cement complete all as specified and directed. Note:- Water proofing liquid compound shall be measured and paid separately.

Supply only liquid water proofing compound complete all as specified and directed.

M&L preparation of newly plastered surfaces of walls of any description and applying two coats of plastic emulsion palint over a coat of primer complete all as specified and directed.

M&L providing and applying plaster of paris putty 1mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and directed.

M&L applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm over new surfaces complete all as specified and directed.

M&L RCC (design mix) M-25 type B1 (using 20mm graded crushed stone aggregate) as in footings,columns, plinth beam ,roof beam etc complete all as specified and directed .

M&L RCC (design mix) M-25 type B1 (using 20mm graded crushed stone aggregate) as in roof beams, cantlevers, bressumers, lintels over 1.5m span complete all as specified and directed.

M&L RCC (design mix) M-25 type B1 (using 20mm graded crushed stone aggregate) as in columns, pillars, piers, posts and struts complete all as specified and directed.

M&L RCC (design mix) M-25 type B1 (using 20mm graded crushed stone aggregate) as in slabs supported on wall, canopies, deck slabs and in shelves and the like complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified, compete all as specified and directed. (Colour as approved by GE)

M&L pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, facia and fixed with self tapping screws as specified. (Colour as approved by GE)

S&F mild steel roof trusses (framed), trussed, purlins, crane gantries. rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, Fe 410-W (Grade E-250) complete all as specified and directed.

S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes,without any attachment complete all as specified and directed.

S&F clip-in false ceiling system with plain steel beveled edged tile (600mm X 600mm) manufactured out of 0.70mm aluminium sheet having powder coating with 60 microns polyester paint on front side. Two sides of each tile shall be rised and piped and stopped to ensure positive engagement into the spring clip-in profile allowing for demounting of individual tiles. The rigid suspension system consists of rows of galivanized steel 0.50mm thick clip-in profile of size 38mm X 20mm and installed at 600mm c/c spacing to support the tiels clilp-in profiles shall be suspended and jointed from galvanized steel 'C' channels of size 10mm X 38mm X 10mm with hold on clamps at spacing as specified by manufacturer. Suspension angles shall be suspended from the roof structure by GI ceiling brackets as per manufacturer's instructions and jointed to the 'C' channels. The tiles shall be held in place by pressure clips 'C' at spacing as per manufacturer's instructions. GI wall angle shall be used on wall angle shall be used on wall of size 20mm X 30mm X 20mm and 0.50mm thick with matching the colour with tiles all as manufacturer's specification/insturctions and including necessary scaffolding all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/window/ceosetory windows & other frames/chowkhat of size 125mm x 65mm comprising of virgin PVC polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwd with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200N (Face) & 1100N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position wiht MS hold fast/lugs/SS dash fasteners of required dia and length complete as per directed of Engineer-in-Charge. (M.S hold fast/lugs of SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 Kg/cum and screw withdrawal strength of 1800 N (Face) & 900N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hold melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per design of Engineer-in-Charge. (Note: Stainless steel butt hinges and necessary S.S screws shal be paid separately).

S&F powder coated aluminium anodised window and ventilator shutters of any type (two/three track) sliding type aluminium powder coating 50 micron and aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprane packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as suitable handle (1 No.) locking & sliding system complete all as specified and directed.

S&F 4mm thick ordinary quality sheet glass ordinary quality and fixing on exsting frame not exc 0.50 sqm in each pane complete all as specified and directed.

S&F framed work such as grills, gratings etc with ends of bars shouldered and/or riveted or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railing; framed work of water tanks and similar work confirming to Fe 290 Gde-E-165 complete all as specified and directed.

S&F 100 mm size aluminium butt hinges,extruded aluminium alloy with galvanised mild steel hinge pin ,anodised, type C-21 complete all as specified and directed.

S&F 300 mm size (length of bolt) aluminium alloy, anodised, sliding door bolt with hasp and staple ,(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F 200 mm size (length of bolt) aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F 150 mm size extruded aluminium alloy handles, cast type, anodised complete all as specified and directed.

M&L preparation of new surfaces of steel of any description, over 10 cm width or girth not other wise described and appliying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer, complete all as specified and directed.

S&F steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing peices, caps and plugs, unions etc.) of nominal bore 15mm complete all as specified and directed.

S&F steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing peices, caps and plugs, unions etc.) of nominal bore 20mm complete all as specified and directed.

S&F sink with drainage made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connection union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F CP swan neck type pillar taps fancy type 15mm bore cast alloy with capasten head screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and flynuts screwed complete all as specified and directed.

M&L for 18-20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs and pillars, window cills, cooking platforms and the like including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite with and including 15mm thick screed bed in CM 1:4, complete all as specified and directed.

Providing edge moulding to 18-20mm thick stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc complete all as specified and directed.

M&L machine cut kota stone slab flooring 18 to 20mm thick laid over cement screed base and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (mirror face) complete over and including 15 mm thick screed in CM (1:4) complete all as specified and directed.

M&L machine cut kota stone slab 18 to 20mm thick in riser of steps,skirting,dado and pillar laid over cement screed base and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (mirror face) complete over and including 10 mm thick backing coat in CM (1:4) complete all as specified and directed.

M&L 40mm thick PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in floor finished even and rough to receive the topping layer complete all as specified and directed.

M&L PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base below floors complete all as specified and directed.

M&L 75mm thick PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in plinth protection and similar works including finishing the surface of concrete topping even & fair without using extra cement complete all as specified and directed.

M&L broken stone or boulder hardcore of gauge n exc.63mm,deposited,spread and levelled in layers n exc,15 cm thick,watered and rammed to a true surface complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints fixed to walls/ laid in trenches or in floors, complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints fixed to walls/ laid in trenches or in floors, complete all as specified and directed.

S&F grating doom 100mm dia with waste hole of PTMT (Min wt 25 gram) complete all as specified and directed.

S&F 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including fixing fittings such as GI nipple for inlet, outlet, washout and overflow etc, including 20mm size ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe including dismantling old cemented/asbestos water/PVC storage tank complete all as specified and directed.

S&F 20mm dia gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F PVC coated mild steel conduit pipe 25mm dia (Drapery rod) with PVC coated MS clamps to hold drapary rod and decorative attachment at one or both ends of drapary rod, fixed to opening of door/windows, each opening n exc 1.50 mtr, contained with a pair of clamps and a pair of side ornamental attachments complete all as specified & directed.

M&L pre-cast cement concrete type B-1 1:2:4 (20mm graded crushed stone aggregate) as in landings, cover slabs for man holes,chullah hoods,chajjas,water troughs,mangers,shelves and similar articles with plain faces, set in CM 1:4 complete all as specified and directed.

S&F 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed .

S&F 75 mm dia PVC (SWR) junction single T equal or unequal complete all as specified and directed .

Treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and directed.

Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed.

Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

Treating the soild along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and directed.

Excavation post holes (or similar holes) in any type of soil each n exc 0.50 cu.m,getting out,returning,filling on and ramming earth or broken rubble mixed with earth around,in layers not exceeding 25cm, complete all as specified and directed.

Returning,filling with approved excavated earth, incl spreading leveling, watering and well ramming in layers not exc 25cm thick with soft loose soil complete all as specified and directed.

Removing excavated material/soil to a distance exc 250m and not exc 500m and depositing where directed complete all as specified and directed.

M&L 75mm PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base rough finished fair and even complete all as specified and directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

M&L plain cement concrete 1:3:6 type C-1 using 20 mm graded stone aggregate cast in situ in lintels up to 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates, water through and the like including weathering, slightly rounded or chamfered angles and throating including use of form work (straight or curved) complete all as specified & directed.

M&L PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

M&L PCC 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) as in surface channels or drains etc complete all as specified and directed.

M&L plain cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate cast in situ in lintels up to 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates, water through and the like including weathering, slightly rounded or chamfered angles and throating including use of form work (straight or curved) complete all as specified & directed.

Supplying and laying or passing through pipe, 1100 volts grade heavy duty cable with XLPE insulated aluminium stranded conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheather 25 Sqmm nominal cross sectional area 3.5 core complete all as specified and directed.

Supplying and laying or passing through pipe, 1100 volts grade heavy duty cable with XLPE insulated aluminium stranded conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheather 16 Sqmm nominal cross sectional area 3.5 core complete all as specified and directed.

Earthing complete with galvanised iron earth plate electrode of size 600mm x 600mm x 6mm thick buried directly under ground vertically to a depth not less than 2.25 metre below ground level with top edge of the earth plate at a depth not less than 1.5 metre below ground level ,connected to galvanised earth lead wire 4.0mm by means of bolts, nuts, check nuts, washer including test point by means of bolts, nuts, check nuts, and washers of galvanized iron and connected to main switch / control board up to 7.5 metre away from earth electrode and including GI pipe light grade 40mm bore protection pipe & necessary excavation and earth work in any strata, PCC chambers in PCC 1:3:6 type B1, RCC 1:2:4 type B1 cover slab 50mm thick with 8mm dia TMT bars at 140mm C/C both ways, with lifting handle, watering pipe of GI medium grade 40mm dia, wire mesh, funnel, lugs and charcoal, salt etc all as applicable and as per plate No 3 of SSR Part-I and all as specified.

Removal of excavated material (soil) to a distance not exc 50m and depositing where directed complete all as specified and directed.

M&L clean dry sand laid in trenches/duct for bedding and cushioning to cable including spreading and levelling complete all as specified and directed.

M&L sub class 'B' brick old size protection cover laid dry flat transversally along the length of cable on cushioning with width equal to the length of brick complete all as specified and directed.

M&L GI tubing (light grade) with all fitting laid in trenches or along pole/bldg or under road crossing and protection pipe or fixed alongwith wall/pole with necessary clamp nut bolt and washer bore for pipe 40mm complete all as specified and directed.

Supply, fixing and testing 70W LED street light fitting IP66 powder coated pressure die cast aluminium high power LED street light with heat resistant toughened glass with lens, complete with all accessories duly prewired and suitable fixing arrangement for mounting on existing MS frame bracket including connecting the fitting and taking down complete all as specified and directed.

S&F bulkhead luminaire fitting with CFL/LED lamps 9/10W complete all as specified and directed.

Supplying, laying and jointing and testing 50mm bore galvanised steel water tubing medium grade (ISI marked) laid in trenchese with medium grade galvanised iron fitting (ISI marked) such as bends, Tees, sockets, nipplese & unions, flanges, reducer etc complete all as specified and directed.

Supplying, laying and jointing and testing 25mm bore galvanised steel water tubing medium grade (ISI marked) laid in trenchese with medium grade galvanised iron fitting (ISI marked) such as bends, Tees, sockets, nipplese & unions, flanges, reducer etc complete all as specified and directed.

Supplying, laying and jointing and testing 20mm bore galvanised steel water tubing medium grade (ISI marked) laid in trenchese with medium grade galvanised iron fitting (ISI marked) such as bends, Tees, sockets, nipplese & unions, flanges, reducer etc complete all as specified and directed.

S&F gun metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed of size 50mm dia complete all as specified and directed.

S&F gun metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed of size 25mm dia complete all as specified and directed.

M&L brick masonry valve pit of size 60x60x60cm (internal dimensions of chamber) built in CM 1:6 including 15cm thick plastering internally with CM 1:6 and flush pointing externally as the work proceeds in same mortar complete with 3.15mm thick MS sheet cover with angle iron 40x40x6mm frame, handle, locking arrangement including privisioning of 2 foot steps made out of MS 15mm round bars removal of surplus material to a distance not exceeding 50 metre and painting steel surface (cover in side and out side with frame) with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L cutting of existing GI pipe line of size 50mm size in position for making branch connection 50mm dia for inserting of Tee complete including Tee of required size and other fitting such as sockets, nipples, unions etc complete including making threads in position for both side as per site requirement complete all as specified and directed.

M&L for point wiring for one light/fan/call bell point controlled by one 5/6 Amp switch with 1.5 Sqmm single core multistranded copper conductor FRLSH, PVC insulated (unsheathed) heavy duty cable including continuous earth wire of size 1.5 sqmm copper conductor multistrand FRLSH, PVC insulated (unsheathed) drawn into and including concealed PVC rigid conduit medium grade ISI marked including Modular GI sheet Metal flush Boxes of any way (as per site requirement) for mounting switches, sockets, fan regulators etc complete all as specified and as directed for the following:- (a) Wiring shall be done by using proper colour coding(b) Earth wire shall be of green colour all as directed .

Description all as per serial item No 89 here-in-before but 6 Amp socket outlet on same board complete all as specified and directed.

Description all as per serial item No 89 here-in-before but socket outlet 6 Amps independent board complete all as specified and directed.

All as per item No 89 above but for 16 Amps on independent board with cables 2.5 sqmm size single core multistranded copper conductor FRLSH, PVC insulated (unsheathed) heavy duty cable including continuous earth wire of size 2.5 sqmm copper conductor multistrand FRLSH, PVC insulated (unsheathed) drawn into and including concealed PVC rigid conduit medium grade ISI marked including Modular GI sheet Metal flush Boxes of any way (as per site requirement) for mounting switches, sockets, fan regulators etc complete all as specified and as directed for the following:- (a) Wiring shall be done by using proper colour coding(b) Earth wire shall be of green colour all as directed

S&F Modular switch 1 way 6 A,1 module, 240 volts ISI marked complete all as specified and directed.

S&F Modular switch 1 way 16 A, 1 module, 240 volts ISI marked complete all as specified and directed.

S&F ceiling rose, 3 terminal surface type complete all as specified and directed.

S&F Single pole and neutral enclosure with 1 two pin and earth plug and a socket complete with one single pole C type MCB, 20 Amp, 240 volts ISI marked complete all as specified and directed.

Supply and fixing LED light fitting 20 Watt 220V, AC decorative box type with built in driver, Ready to use type connecting up with three core flexible copper conductor cable of suitable size from celling rose complete all as specified and directed.

S&F LED Bulb 9 watt with angle lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

Supply and fixing LED light fitting 10 Watt 220V, AC decorative box type with built in driver, Ready to use type connecting up with three core flexible copper conductor cable of suitable size from celling rose complete all as specified and directed.

Supply and fixing celling fan complete with blades, down rod , electronic reulator and acessories,, 230 V 1200 sweep,Min air delivery 210CFM with service value 6.00BEE, Five start rated with brushless direct current motor (BLDC), complete all as specified and directed by Engr-in-Charge.

M&L distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 8 way 240 volts double door complete all as specified and directed. Note:- Distribution board and MCB's should be same make.

S &F of SPN 40 to 63 Amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

Supply and fixing MCB ‘B’ curve suitable for 230 volts AC supply, 06 to 32 Amps, SP with over load and short circuit protection and rupturing capacity not less than 10 KA, fixing in DB complete all as specified and as directed by Engineer-in-charge

Supply & Fix electric water geyser, S&F new electric storage Heater (vertical type Geysers) 25 Ltrs BEE RATING 5 STAR, 230 volts AC single phase with and including grouting with high tensile rag bolt, nut & washer etc as directed as per site requirement and making and including necessary inlet / outlet water PVC connection for Geysers. Geysers to have glass lines tank, fero glass coated container, PUF insulation, glass coated heating element, thermostat cut off etc. complete all as specified and as directed.

S&F GI pipes 15mm bore ISI marked medium grade with all fittings complete fixed on floor / wall with and including clamp including vent pipe etc complete all as specified and directed by Engineering-in-Charge.

M&L for cutting & screwing existing steel tubing 15mm dia bore size for alternations or additions required for connection with inlet pipe of Geyser complete all as directed.

S&F angle cock with flange15mm bore heavy duty fancy type chromium plated with long shank and cup concealed in wall complete all as directed.

S&F 15mm dia CP Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe complete all as directed.

M&L for sub main wiring with proper colour coding, insulated, unsheathed, multistranded, copper conductor FRLS, cable of 2 run 10 Sq mm for phase and neutral and one run of 10.0 Sq mm for earth wire unsheathed, multistranded, copper conductor FRLS, drawn through including medium grade ISI mark PVC concealed conduit fixed on wall. Note: Two runs of cable for phase/neutral and one run of cable for earth will be measured and paid as one unit length complete all as specified and directed. Note : Wiring shall be done in proper colour coding.

MM Constructions (BID ID -3277778)