C/o District Panchayat Resource Centre at Nahan, Sirmaur (HP)

Amount

Cutting in earth work in by mechanical mean in all heights and depths in all kinds of soils, including saturated soils comprising of pick work , Jumper work and blasting work both in soft and hard rock with chiseling and wedging out of rock (Where blasting is prohibited) and their intermediate classification of soil including, dewatring where required, setting out to required lines, levels as shown on the drawing and directed by the Engineer-in - charge at site, according to the HP.PWD. specification of 1990( One Thousand Nine Hundred ninety) Volume-I (One) and sorting out useful and unuseful matreial and Transportation of the unuseful matreial for disposing at dumping site ( To be arranged by the Contractor) as per satisfacation of Engineer -in- Charge through all modes of transportation including head load , animal load or mechnical means along with its leveling fine dressing and with all kinds of labour, machineries, tools equipments and safety measures and incidentals necessary to complete the work by mechnical means and labour( If required). All useful material such as stone , shingles aggregate and slates shall be properly stacked at site to the maximum possible extent in all leads and lifts through all modes of transportation as per direction of the Engineer -in -charfe . The recovery for stones, weather useful or not, for the minimum quatom of 99.52 cubic meter @ Rupee 300/- Only (Rupees. Three hundred) per cubic meter shall be effected on pro rata basis in all circumstances. Any loss to the public and private property during the course of execution and disposal of serviceable and unserviceable materials shall be the absolute responsibility of the contractor and shall have to be duly compensated by him in all respect including all incidental charges.

Excavation in foundation and trenches in earth work in all heights and depths in all kinds of soils, including saturated soils comprising of pick work, jumper work and blasting work both in soft and hard rock with chiseling and wedging out of rock (where blasting is prohibited) and their intermediate classification of soils including, dewatering wherever required, setting out to required lines, levels as shown on the drawing and directed by the Engineer -in-charge at site., according to the HP.PWD. specification of 1990 (one thousand nine hundred ninety) volume-I (one) and sorting out useful and unuseful material and transportation of the unuseful material for disposing at dumping site (To be arranged by the contractor) as per satisfaction of Engineer- in -charge through all modes of transportation including head load ,animal load or mechanical means along with its leveling fine dressing and with all kinds of labour, machineries, tools equipments and safety measures and incidentals necessary to complete the work by mechanical means and labour ( if required ). All useful material such as stones, shingles aggregate and slates shall be properly stacked at site to the maximum possible extent in all leads and lifts through all modes of transportation and used /removed as per the direction of the Engineer - in- charge. Any loss to the public and private propriety during the course of execution and disposal of serviceable and unserviceable materials shall be the absolute responsibility of the contractor and shall have to be duly compensated by him in all respect including all incidental charges.

Earth work in excavation for all type of road structures such as retaining walls, breast walls, culverts, drains and parapets ectetra in all type of classification of soil comprising of ordinary soil, soft/ hard rocks, chiselling / wedging out of rocks (where blasting is prohibited) as per drawing and MORD technical specifications Clause 305.1, 1104 and 1606.1 and as per direction of the Engineer-in-Charge including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal of materials upto all leads and lifts including dressing of sides and bottom and back filling in trenches with excavated suitable approved materials to the original surface in layers not exceeding 150mm (One Hundred Fifty milimetres) compacted thickness including shorting and strutting and pumping and bailing out water (surface and sub soil water) upto all depth and any quantum of water including cleaning of slush which may arise out during dewatering as per the direction of Engineer-In-Charge and including of carriage of materials with in all leads and lifts.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete including carriage of materials through all modes of transportion with in all leads and lifts and as per HP.PWD. specifications of 1990 volume-I and as per direction of Engineer-in-charge.

Providing form work with steel plates 3.15mm. (Three point fifteen milimetre) thick welded with angle iron in frame 30X30x5mm.(Thirty into thirty into five millimeter) so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden/ steel battens and ballies, height of propping and centring below supporting floor to ceiling to any floor height and removal of the same for in situ-reinforced concrete and plain concrete work and as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

In foundation, footings, bases of columns etc. and mass concrete.

In flat surfaces such as soffits of suspended floors, roofs, landings and the like of any thickness in all floor level in all heights.

Columns,pillars,posts and struts Square,rectangular or polygonal in plan in all floor level in all heights.

Stair cases with sloping or stepped soffits excluding landing in all floor level in all heights.

Beams, Cantilever, girders and lintels. Sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels in all floor level in all heights.

Edges of slabs and break in floors and walls in any width.

In vertical surface such as wall (any thickness) partition and the like including attached pilasters in all floor level in all heights.

Providing and laying cement concrete 1: 6:12 (One cement : Six sand: twelve graded/ crushed stone aggregate 40mm (Forty milimetre) nominal size) mechnically mixed and curing complete excluding the cost of form work in foundation and plinth including carriage of materials through all modes of transportations with in all leads and lifts and as per HP.PWD.specifications of 1990 volume-I and as per direction of Engineer-in-charge.

Providing and laying cement concrete 1:4:8 (One cement: Four sand :Eight graded cursed/broken stone aggregate 40mm (forty millimeters) nominal size) mechanically mixed and curing complete, excluding cost of form work in foundation and plinth including carriage of materials through all modes of transportion with in all leads and lifts and as per HP.PWD. specifications of 1990 volume-I and as per direction of Engineer-in-charge.

Providing and laying concrete for plain/ reinforced concrete in open foundation1:4:8 (One cement: Four sand :Eight graded cursed/broken stone aggregate 25mm (twenty five millimeters) nominal size, mechanically mixed as per drawing & MORD technical specification clause 802, 803, 1202 & 1203 in retaining walls, breast walls,including centring & shuttering including carriage of materials through all modes of transportion with in all leads and lifts and as per HP.PWD. specifications of 1990 volume-I and as per direction of Engineer-in-Charge.

Providing and laying reinforced cement concrete 1:2:4 (1 cement : 2 Sand : 4 graded stone aggregate 20mm nominal size) to give a smooth and even surface including centring and shuttering etc. but excluding cost of reinforcement in string courses, copings, bed plates, anchor blocks, plain windows sills and the like in all floor level in all heights including carriage of materials through all modes of transportion with in all leads and lifts and as per HP.PWD. specifications of 1990 volume-I and as per direction of Engineer-in-Charge

Providing and laying cement concrete 1:2:4 (one cement isto two sand isto four crushed stone aggregate 20mm. (Twenty millimeter) nominal size) mechanically mixed and vibrated, curing complete excluding cost of form work and reinforcement for reinforced concrete work and as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

In suspended floors roofs, landings and shelves and their supports, balconies, beams, girders, bressumers and contilevers in super structure for all floor and in all heights

Providing and laying cement concrete 1:1.5:3 (one cement isto one point five sand isto three crushed stone aggregate 20mm. (Twenty millimeter) nominal size) mechanically mixed and vibrated, curing complete excluding cost of form work and reinforcement for reinforced concrete work and as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

In Foundation, footings bases of columns etc. and mass concrete.

In suspended floors roofs, landings and shelves and their supports, balconies, beams, girders, bressumers and cantilevers upto floor all level in all heights.

In columns, pillars, posts and struts. Square, rectangular or polygonal in plan, in all floor level in all heights.

In stair cases with sloping or stepped soffits excluding landings in all floor level in all heights.

In walls (any thickness but not less than 0.10m) attached pilasters, buttresses, plinth and string courses etc from top of foundation in all floor level in all heights.

Providing & laying cement concrete work mechnically mixed & vibrator 1: 1.5 : 3 ( One cement : One & half approved sand : three graded crushed stone aggregate 20mm ( twenty milimeter ) nominal size ) reinforced concrete chajja of any thickness upto floor all level including finishing the exposed surface with cement mortar 1:3 ( One cement : three approved sand )to give a smooth & even surface centring/form work & curing complete excluding the cost of reinforcement including carriage of materials within all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge as per HP.PWD., specification 1990 Volume- I ( One ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing Tor / TMT steel reinforcement of TATA Tiscon/SAIL/Rashtria Ispat incluiding cost of binding wire for R.C.C. work including cutting, bending, binding and placing in position complete in all floor levels in all heights including carriage of materials through all modes of transportations with in all leads and lifts and as per HP.PWD. specifications of 1990 volume-I and as per direction of Engineer-in-Charge.

Brick work using common burnt clay building bricks in foundation and plinth in Cement Mortar 1:6 (One cement : Six sand) Second Class Bricks including carriage of materials through all modes of transportion with in all leads and lifts and as per HP.PWD. specifications of 1990 volume-I and as per direction of Engineer-in-Charge.

Providing and laying brick work using common burnt clay building brick in Cement Mortar 1:6 (One cement:Second sand) Second class bricks in super structure for all floors levels and in all heights including carriage of materials through all modes of transportations with in all leads and lifts and as per HP.PWD. specifications of 1990 volume-I and as per direction of Engineer-in-Charge.

Providing and laying second classs half brick masonry in common burnt clay building bricks in foundation and plinth level in Cement Mortar 1:4 (One cement: Four sand) including carriage of materials through all modes of transportion with in all leads and lifts and as per HP.PWD. specifications of 1990 volume-I and as per direction of Engineer-in-charge.

Providing and laying second class half brick masonry in common burnt clay building bricks in cement Mortar 1:4 (One cement: Four sand) in super structure for all floor levels in all heights including carriage of materials through all modes of transportations with in all leads and lifts and as per HP.PWD. specifications of 1990 volume-I and as per direction of Engineer-in-charge.

Stone soling tightly hand packed under floors, including watering, ramming and consolidating complete and carriage of materials, labour ,tool and plants through all modes of transportation with in all leads and lifts, as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and laying Random rubble masonry / polygonal rubble masonry (uncoursed/brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (One cement : six sand : twelve crushed stone aggregate 20mm (Twenty millimeter nominal size) at plinth level in Cement Mortar 1:6 (One cement: six sand) and curing complete including all carriage of materials, labour ,tool and plants through all modes of transportation with in all leads and lifts, as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing anodised aluminium work for door, windows, ventilators and partitions with extruded built up standard tubular and other sections of approved make confirming to IS 733 and IS 1285 anodised transparent or dyed to required shade according to IS 1868. (minimum anodic coating of grade AC 15) fixed with rawl plugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, straight, mitred and jointed mechanically where ever required including cleats angle, aluminium, snap beading for glazing/panelling C.P. brass/stainless steel screws as per Architectural drawings and as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

For frames of windows and ventilators and glazed partitions.

For shutters of windows and ventilators including providing and fixing hinges/pivots and making provisions for fixing of fittings where ever required including the cost of PVC/neoprene gaskets as required ( fittings and glazing/panelling shall be paid for separately)

Providing and fixing glazing in aluminium door,window,ventilators shutters & partitions etc. with PVC/neopprene gasket etc. complete as per the architectural drawings and the direction of Engineer-in-Charge ( Cost of aluminium snap beading shall be paid for separately ) glazing with glass pans of 6/5.5 mm ( Six/ Five point five milimeter ) thickness ( weight not less than 13.75 Kg/ Sqm ( Thirteen point seven five Kilogramme per square meter ) as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing fly proof satinless steel wire gauge of IS gauge designation 140g with wire of dia 0.71milimetre in aluminium frame of shutters of doors,windows, ventilators and partitions etc. with PVC neoprene gasket and M.S. flats of required size etc.complete as per the Architectural drawing & as per direction of Engineer-in-Charge (Cost of snap beeding shall be paid in basic items) as per HP.PWD., specification1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing & fixing mild steel plain grills of required pattern in aluminium frames of windows & vents with 80mm x 80mm ( Eighty milimeter into eighty milimeter ) panel holes with 25 x 8 mm ( Twenty five into eight milimeter ) thick mild steel flat, square or rounded headed bolts & nuts or by screws complete in aluminium channels base frame ( aluminium base frames to be measured & paid for separately ) complete as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction/ direction of the Engineer-in-Charge.

Providing & fixing door shutters with 40 mm thick frame of Second class Deodar wood for doors with panel of 12mm ( Twelve milimeter ) thick MDF board preliminated ( Both side ) phenol bonded particle board ISI marked No. IS 12823 exterior/ interior grade panelled shutters including bright finished/black enamelled iron butt hinges with necessary screws frame as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction/ direction of the Engineer-in-Charge.

Providing & fixing door shutters with 40 mm thick frame of Second class Deodar wood for doors with panel of 12mm ( Twelve milimeter ) thick MDF board preliminated ( one side ) phenol bonded particle board ISI marked No. IS 12823 exterior/ interior grade panelled shutters including bright finished/black enamelled iron butt hinges with necessary screws frame as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction/ direction of the Engineer-in-Charge.

Providing and fixing 19mm (Nineteen milimetre) thick cub board shutters of commercial board ISI marked IS 1659 of uniply/green ply or its equivalent) for with butt joints & fixing with nails & screws etc. complete as per HPPWD specification 1990 volume-I includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge.

Providing and fixing 19mm (Nineteen milimetre) thick water proof commercial board (ISI marked) in shelves/boxes for cup boards including fixing with nickel plated piano hinges with screws etc. complete as per HPPWD specification 1990 volume-I includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge

Providing & fixing 8 mm ( eight milimeter ) thick ply wood lining with butt jointing and nails ( Frame work and cover fillets to be measured and paid for seapatately ) as per HPPWD specification 1990 volume-I includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge

Providing and fixing 1.00mm (one milimetre) thick coloured or plain lamination sheet (ISI mark) (sunmica) on boards/ply wood sheets with approved adhesive and nails etc complete as per HPPWD specification 1990 volume-I includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge.

Providing sal wood work in frames of flase ceiling partitions etc. sawn and put-up in position as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing plain square edged cover fillets ( Beading ) 50 x 12 mm ( Fifty into twelve milimeter ) section, with wood screws in ceiling and lining including mitring at junction Ist class deodar wood as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing and fixing ACP tiles in ceiling of size 600x600 mm of approved shade and pattern including moulded on powder coated G.I. frame work fixed/hanging with wall or ceiling etc. with specified clamp and G.I. wire rawl plug etc. complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing Chormium plated mild steel sliding door bolt bright finished with bolts and nuts screws etc. complete for all floors, including carriage of materials, labour ,tool and plants through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

300×16mm (Three hundred into sixteen millimeter)

250×16mm (Two hundred fifty into sixteen millimeter)

Providing and fixing powder coated aluminium tower bolts (barrel type) anodized trans parent or dyed to required shade and colour with screws etc. complete, including carriage of materials , labour ,tool and plants through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

250×10mm (Two hundred fifty into ten millimeter)

150×10mm (One hundred fifty into ten millimeter)

Providing and fixing powder coated aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete for all floors, including carriage of materials , labour ,tool and plants through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

125 mm ( One hundred twenty five milimetre ) size

75 mm ( Seventy five milimeter ) size.

Providing & fixing powder coated aluminium hooks & eyes transparent or dyed to required colour or shade with necessary screw. 250 mm ( Two hundred fifty milimeter ) size as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing aluminium 100 mm ( One hundred milimeter ) floor door stopper with rubber cushion screws etc. to suit shutter thickness complete as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing chromium plated brass 100 mm rim latch and lock & pair of knob with necessary screws etc. complete ( Indian type ) as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing mild steel single acting spring hinges bright finished with necessary screws etc. complete 125 mm ( One hundred twenty five milimetre ) size as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing over head hydraulic door closer of approved brand & manufacture conforming to IS specification ISI marked ) for door with screws complete as per HPPWD specification 1990 volume-I ( One ) including carriage of all labour equipments & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing plain lining with tongued & groved jointing & screws ( Frame work & cover fillets to be measured & paid for separately ) Ist class Indian teak wood 20 mm ( twenty milimeter ) thick as per the direction of the Engineer-in-Charge, including all leads, lifts & carriage of materials & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing glass strips in joints of terrazo / cement concrete floor 40 mm wide & 4 mm ( Forty milimeter wide and four milimeter ) thick as per the direction of the Engineer-in-Charge, including all leads, lifts & carriage of materials & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

40mm ( forty milimeter ) thick cement concrete flooring 1:2:4 ( One cement : two approved sand : four graded stone aggregte 20mm( twenty milimetre ) nominal size ) laid in one layer finished with a floating coat of neat cement in all floor level as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entiresatisfaction of Engineer-in-Charge.

50mm ( fifty milimeter ) thick cement concrete flooring 1:2:4 ( One cement : two approved sand : four graded stone aggregte 20mm( twenty milimetre ) nominal size ) laid in one layer finished with a floating coat of neat cement in all floor level as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entiresatisfaction of Engineer-in-Charge.

Providing and laying 25 mm (Twenty five milimetre) thick Mirror Polished Kota stone slab flooring with 20mm (twenty milimetre ) thick base of cement mortor 1:4 (one cement is to four sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab and as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and laying 25mm (twenty five milimetre ) thick Mirror polished Kota stone slab in risers of steps ,skirting dado and pillars laid on 12 mm (average) thick cement morter 1:3 (one cement isto three sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing & laying granite stone in flooring 20mm ( Twenty milimeter ) ( average ) thickness base of cement mortar 1 : 3 ( One cement : three sand ) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone including rubbing & polishing complete as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipments and materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Extra for flaming / etching of grainte stone in required width and length as per approved Architectural drawing as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipments and materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction / direction of the Engineer-in-Charge.

Providing & laying marble work ( Table rubbed and polished ) in flooring 20mm ( twenty milimetre ) thick base in cement mortar 1:3 ( one cement : three approved sand ) including jointing with cement mortar 1:2 ( One cement : two marble dust ) with an admixure of pigment to match the shade of the marble. 20mm ( twenty milimetre ) thick white Makrana marble having grey streaks upto 2.05 mtrs. height as per HP.PWD.,specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts and other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

First class white/coloured glazed tiles in skirting,risers & dedo of Nitco, Kajaria / Orient etc. or equilevent of approved shade 12 mm ( tweleve milimeter ) thick cement mortar 1:3 ( One cement : three approved sand ) & jointed with cement slurry finished with flush pointing in white cement as per HP.PWD.,specification 1990 Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

Providing & laying Duro stone vetrified tiles { 600 x 600 x 12 mm ( Six hundred into six hundred into twelve milimeter ) } of Nitco, Kajaria / Orient etc. or equilevent of approved shade with boarders in grey coloured or of approved shade in flooring, treads of steps and landing laid on a bed of 12 mm ( Twelve milimeter ) thick cement mortar 1 : 3 (One cement : three sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete as per HP.PWD.,specification 1990 Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

Providing & laying Duro stone vetrified tiles { 300 x 300 x 8 mm ( Three hundred into three hundred into eight milimeter ) } of Nitco, Kajaria / Orient etc. or equilevent of approved shade in skirting risers of steps & dedo on 12mm thick cement mortar 1 : 3( One cement : three sand ) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete as per HP.PWD.,specification 1990 Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

Providing & laying 15mm thick Single slab Endura vetrified tiles stepping stone of heavy duty double charge vetrified tiles { 600 x 600 x 15 mm ( Six hundred into six hundred into fifteen milimeter ) } of ORIENT-BELL/RAK/AGL/NITCO in grey coloured or of approved shade in flooring, treads of steps & landing laid on a bed of 12 mm ( twelve milimeter ) thick cement mortar 1 : 3 ( One cement : three sand ) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete as per HP.PWD.,specification 1990 Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

Providing & fixing Garsa stone 12mm ( twelve milimeter ) cladding on reinforced cement concrete surface side on faces of Arch masonry wall etc. on 12 mm ( twelve milimeter ) thick cement plaster 1 : 3 ( One cement : three sand ) and jointed with cement slurry including scaffolding etc. complete as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts and other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

Providing and fixing 0.60mm ( Zero point six zero milimeter ) thick prepainted steel sheet of TATA DURASHINE in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing ridges or hips 60 cm overall with 0.60mm thick prepainted steel sheets of TATA Durashine in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete as per HP.PWD., Specifications of 1990 volume-I includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge.

Providing and fixing valley 90 cm overall 0.60mm thick prepainted steel sheet of TATA Durashine in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia with prepainted G.I. limpet and bitumen washers complete as per HP.PWD., Specifications of 1990 volume-I includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge.

Providing and fixing flushing 38cm overall with 0.60mm thick prepainted steel sheet of TATA Durashine in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia meter & prepainted G.I. limpet & bitumen washers complete as per HP.PWD., Specifications of 1990 volume-I includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge.

Providing and fixing thiclk 30cm wide 30cm deep 120cm overall box type 0.45mm thick plain prepainted steel sheet of TATA Durashine gutter with bolts and nuts and washers etc. including making conection with rain water pipe complete as per design including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing & fixing M.S. B.P. sheet 2mm ( Two milimetre ) thick in eaves board/facia/ soffits/ ceiling including cutting fixing & welding to steel roof mambers and applying a coat of red lead primer complete ( Base member of steel work shall be measured & paid for separately ) as per HP.PWD., specification Volume-I ( one ) including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing on wall face150mm ( One hundred fifty milimeter ) dia PVC rain water pipes of working pressure not less than 4.5 Kg ( Four decimal five kilogram ) per square meter including filling the joints with approved adhesive complete as per HP.PWD.,specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts and other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts and other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

150mm ( One hundred fifty milimetre ) dia

Providing and fixing 150mm ( One hundred fifty milimetre ) dia PVC collars ISI marked approved design with steel screws and rawal plugs etc. complete as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts and other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

Providing and fixing 150mm dia M.S. sheet clamps for PVC pipes with steel screws and rawl plugs complete including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts as per direction of Engineer-in- Charge.

100 mm ( One hundred milimetre ) dia

75mm ( Seventy five milimetre ) dia

Providing & fixing single rebate door frame manufactured from ISLC 75 mm ( Seventy five milimeter ) ( With mild steel flat 75 x 4 mm ( Seventy five into four milimeter ) for centre frame ) and mild steel hollow section for rebate 40 x 12 mm ( forty into twelve milimeter and 1.5 mm ( One point five milimeter ) thick welded together for making rebate including mild steel flat hold fast 20 cm ( twenty centimeter ) long and 4 mm ( four milimeter ) thick embedded in cement concrete block 1 : 3 : 6 ( One cement : three sand : six graded stone aggregate twenty milimeter nominal size ) as per design & drawing including jamb, lock jamb, beed and if required angle threshold of mild steel angle 50 x 25 mm ( fifty into twenty five milimeter ) welded or rigidly fixed by mechanical means lugs with aplit end tails to each jamb including steel butt hinges 2.5 mm ( two point five milimeter ) thick with provision for locking arrangement and shock absorbers as specified & applying a coat of steel primer after pretreatment of the surface complete as per HP.PWD.,specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts and other incidental charges complete as per entire satisfaction of the Engineer-in Charge.

Side / end frame

Side / end frame

Providing & fixing steel glazed doors,windows & ventilators of standard rolled steel Z section with horizontial & vertical sashbar of angle iron ( 25x25x3mm ) ( Twenty five into twenty five into three milimeter ) T-section ( 25x25x 3mm ) ( Twenty five into twenty five into three milimeter ) in fixed and openable shutters as per standard Architectural drawing,jointed mitred & welded with mild steel Channel framed or with fixing clips or with bolts & nuts as required & iron fitting, including providing & fixing of glass pans with glazing clips & special metal sesh putty of approved make complete including applying a priming coat of red lead paint as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Fixed steel windows.

Side hung steel windows.

Providing steel work of TATA SALT or RASHTRIYA ISPAT welded in built up sections/hollow section in trusses and framed work, including cutting,hoisting , fixing in position and applying a priming coat of red lead paint complete as per HP.PWD., Specifications of 1990 volume-I includng carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-Charge.

In trusses and trussed purlings in buildings

In gratings, framed, guards, bars ladders and railing, brackets and similar works.

Providing & fixing MS round holding down or anchor bolts with nuts and washers plates complete as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing moulded hand rail of mild steel hollow pipe 50 mm ( fifty milimetre ) dia welded in stright length over mild steel flat at top of vertical balusters including one coat of red oxide priming coat complete ( mild steel flat & baluster of railing shall be measured & paid for sepataely ) as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing satinless steel railing hollow pipe 50 mm ( Fifty milimeter ) dia welded with stainless steel flat at top of vertical baluster & moulded hald rail with semi round nosing complete as per Architectural drawing complete in all respect as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per direction of the Engineer-in-Charge

Painting two coats ( excluding priming coat ) on new steel & other metal surface with enamel paint brushing to give an even shade including cleaning the surface of all dirt, dust & other foreign matters with other then white as per HPPWD specification 1990 Volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Applying priming coat over new wood & wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt & other foreign matter, sand papering & knotting ready mixed paint brushing primer pink as per HPPWD specification Volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Painting two coats ( excluding priming coat ) on new wood & wood based surface with enamel paint to give an even shade including cleaning the surface of dirt, dust & other foreign matter sand papering & stopping with enamel paint other than white as per HPPWD specification 1990 Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Polishing two coats with french polish on new wood & wood based surface to give an even surface including cleaning the surface of all dirt, dust & sand papered smooth & including a coat of wood filler as per HPPWD specification 1990 Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Applying white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Applying one coat of Acrylic primer/ Asian primer or its equivelent of superior quality on new concrete/ plastered surfaces after & including preparing the surface by thoroughly brushing the surface free from mortar drops, dust,loose materials and other foreign matter sand papering smooth the surface complete as per HP.PWD., specification Volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Finishing wall with weather proof exterior grade premium emulsion of Asian paints/Apex Ultima or its equivelent of approved shade on undecorated wall surface ( two coats ) to give an even shade & final finish after thoroughly cleaning the surface to remove all dirt, dust & other foreign matter etc. including sand papering smooth in all external plastered surfaces as per HP.PWD., specification 1990 Volume-I ( one )including carriage of all labourequipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Applying priming coat on new concrete/masonry/asbestos cement/masonry/ plastered surface surface after and including preparing the surface by thoroughly cleaning oil, grease, dirt & other foreign matter and sand papering as required Ready mixed primer as per HP.PWD., specification 1990 Volume-I ( one )including carriage of all labourequipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Wall painting (two coats) with premium enamel paint Kemolite of Asian paint or its equivelent upto 140 cm ( One hundred forty centimetre ) height having two Nos. bands 5cm wide each above 125 and 135cm. ( One hundred twenty & One hundred thirty five centimetre ) Height of approved shade as per pettern to detail on undecorated cobcrete/ plastered wall surface to give shade and final finish after thoroughly cleaning the surface to remove all dirt, dust and other foreign matters etc. including sand papering smooth as per HP.PWD., specification 1990 Volume-I ( one )including carriage of all labourequipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

6mm ( six milimetre ) cement plaster to ceiling with cement mortar 1:3 ( One cement : three approved sand )as per HP.PWD., specification 1990 Volume-I ( one )including carriage of all labourequipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

15mm ( fifteen milimetre ) cement plaster in single coat on rough side of brick/ concrete/stone walls of interior plastering upto floor two level including arrises,internal rounded angles, chamfers & rounded angles not exceeding 80mm in ( eighty milimetre ) grith finished even and smooth in cement mortar 1:6 ( One cement : six approved sand) as per HP.PWD.,specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

15mm ( fifteen milimetre ) cement plaster in single coat on fair side of brick/ concrete/stone walls of interior plastering upto floor two level including arrises,internal rounded angles, chamfers & rounded angles not exceeding 80mm in ( eighty milimetre ) grith finished even and smooth in cement mortar 1:6 ( One cement : six approved sand) as per HP.PWD.,specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

15mm (fifteen milimetre)cement plaster in single coat on fair side of brick/ concrete/ stone walls of interior plastering upto floor two level including arrises,internal rounded angles, chamfers & rounded angles not exceeding 80mm in (eighty milimetre) grith finished even and smooth in cement mortar 1:4(One cement:four approved sand) as per HP.PWD., specification volume-I (one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Distempering two coats with Ist quality oil bound washable distemper of Asian paints or equivalent of approved shade and manufacture and of required shade on undecorated ceiling/slopping surfaces to give an even shade over and incluidng a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth priming coat with distemper primer for all floors including entire carriage of materials through all modes of transportation with in all leads and lifts as per PWD specifications and as per direction of Engineer-in-Charge.

Distempering two coats with Ist quality oil bound washable distemper of Asian paints or equivalent of approved shade and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth priming coat with distemper primer for all floors including entire carriage of materials through all modes of transportation with in all leads and lifts as per PWD specifications and as per direction of Engineer-in-Charge.

Providing under layer for plinth protection of 75mm thick (unconsolidated) bed dry brick/stone aggregated 40mm nominal size with rammed and consolidated and grouted with fine sand including preparation of ground completeas per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing plinth protection 50mm (fifty millimetres) thick in cement concrete 1:3:6 (one cement : three sand: six crushed stone aggregate 20mm (twenty millimetres) nominal size) as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Construction of "U" shape cement concrete 1:3:6 drain of size 15x20 centimetre plastered inside with floating coat of neat cement complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing screen with main frame of size 50mmx50mm M.S. hollow square pipe section and distributing member of 25x25 mm M.S. hollow square pipe complete in all respect as per architectural drawing including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing & laying in trenches, galvanised mild steel tubes ( Medium grade ) , tube fitting ( earth work in trenches to be measured & paid for separately ) )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

15 mm ( Fifteen milimetre ) nominal bore

20 mm ( Twenty milimetre ) nominal bore

Making connection of galvanised steel distribution branch with galvanised mild steel main 20 mm to 40 mm ( Twenty milimeter to forty milimeter ) nominal bore by providing & fixing tee including cutting & threading the pipes complete as per HP.PWD., Specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Fixing water metre stop cock in galvanised mild steel tube including necessary fitting such as mild steel galvanised jam nuts,sockets, etc. cutting & making long screws, complete ( Water metre & stop cock to be measured & paid for separately) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

15 mm ( Fifteen milimetre ) nominal bore

Providing and fixing 10000 litres net capacity PVC water storage tank of ISI : 12701 marked,G.I. inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting upto all heights above ground level as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing & fixing brass full way valve with wheel 20 mm ( twenty milimeter ) nominal bore as per HPPWD.,specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing G.I. / M.I. Union of following sizes ( Where not included in the items )as per HPPWD.,specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

15 mm ( fifteen milimeter ) dia

20 mm ( Twenty milimeter ) dia

Providing & fixing plytheline- Aluminium Polyethylene ( PE-AL-PE ) composite pressure pipe U.V. stabilized with carbon black confirming to IS-15450-2004 water supply including clamps at one metre spacing, cutting, fixing & making good the wall etc. but excluding the cost of fitting ( Internal work ) pipes exposed on wall internal work-Exposed as per HPPWD., specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

1216 ( One thousand two hundred sixteen ) ( 16 mm ( Sixteen milimeter ) outer dia pipe )

1620 ( One thousand six hundred twenty ) ( 20 mm ( twenty milimeter ) outer dia pipe )

Providing & fixing PE-AL-PE- composite internal seal compression fitting as per IS-15450-2004 for hot water supply such as tees, elbows, reducers, connector, couplers & clamps with jointing testing & fixing including cutting & making good the walls etc. ( This type of fitting to be used for hot water supply only ) as per HPPWD.,specification volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Equal Tees :-1216 mm ( One thousand two hundred sixteen milimeter ) size

1620 mm ( One thousand six hundred twenty milimeter ) size

Reducing Tees:- 1620 ( One thousand six hundred twenty into all branches

Female branch Tees :-1216 x 1216 x 15mm ( One thousand two hundred sixteen into One thousand six hundred sixteen into fifteen milimeter ) thread

1620 x 1620 x 20 mm ( One thousand six hundred twenty into One thousand six hundred twenty into twenty milimeter ) thread

Female Elbows :-1216 x 15mm ( One thousand two hundred sixteen into fifteen milimeter ) thread

1620 x 15mm ( One thousand six hundred twenty into fifteen milimeter ) thread

Male thread connector :-1216 x 15mm ( One thousand two hundred sixteen into fifteen milimeter ) thread

1620 x 15mm ( One thousand six hundred twenty into fifteen milimeter ) thread a

Female thread connector :-1216 x 15mm ( One thousand two hundred sixteen into fifteen milimeter ) thread

1620 x 15mm ( One thousand six hundred twenty into fifteen milimeter ) thread

Couplers :-1216 ( One thousand two hundred sixteen ) ( 16 mm ( Sixteen milimeter ) outer dia pipe )

1620 ( One thousand six hundred twenty ) ( 20 mm ( twenty milimeter ) outer dia pipe )

Reducers :- 1620 x 1216 ( One thousand six hundred twenty into one thousand two hundred sixteen milimeter ) outer dia pipe )

Providing and fixing high pressure PVC spigot & socket, waste & ventilating pipes ISI marked including fixing with approved adhesive etc. complete as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

150mm (One hundred fifty milimetre ) dia

110mm (One hundred ten milimetre ) dia

75mm ( Seventy five milimetre ) dia

Providing & fixing PVC door bend with oval access door insertion rubber washers 3mm ( three milimeter ) thick bolts & nuts ISI marked complete including fixing with approved adhesive etc. complete including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

150mm (One hundred fifty milimetre ) dia

110mm (One hundred ten milimetre ) dia

75mm ( Seventy five milimetre ) dia as

Providing & fixing PVC collars ISI marked including fixing with approved adhesive etc. complete as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

100mm (One hundred milimetre ) dia

75mm ( Seventy five milimetre ) dia

Providing & fixing PVC Plain bend ISI marked including fixing with approved adhesive etc. complete as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

100mm (One hundred milimetre ) dia

75mm ( Seventy five milimetre ) dia

Providing & fixing PVC double equal branch with oval access door insertion rubber washers 3mm ( three milimeter ) thick bolts & nuts ISI marked complete including fixing with approved adhesive etc. complete as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

150mm (One hundred fifty milimetre ) dia

110mm (One hundred ten milimetre ) dia as

75mm ( Seventy five milimetre ) dia

Providing & fixing PVC reducer ISI marked including jointing with approved ahesive etc. complete as per HP.PWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

150mm x 110mm (One hundred fifty milimetre into one hundred ten milimeter ) dia

110mm x 75mm (One hundred ten milimetre into Seventy five milimeter ) dia

Providing & fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floor etc. complete as per HPPWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

110mm x 90 mm dia ( One hundred ten milimeter into seventy five milimeter ) dia

110mm x 75 mm dia ( One hundred ten milimeter into seventy five milimeter ) dia

Providing & fixing PVC cowl ISI marked including fixing with approved adhesive etc. complete as per HPPWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

150 mm ( One hundred fifty milimeter ) dia

110 mm ( One hundred ten milimeter ) dia

75mm (seventy five milimeter ) dia

Providing & fixing PVC waste pipe of ISI marked including fixing with approved adhesive complete for wash basin or sink. 32 mm ( thirty two milimeter ) dia as per HPPWD.,specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing Vitreous China wash down water closet ( Orrisa pattern ) Orrisa Pan W.C.No. 2071 size 58 x 44cm ( Fifty eight into forty four centimetre ) in white shade of Cera or its equivelent ( Earth work, bed concrete,foot rest & trap to be measured & paid for separtely ) as per HP.PWD., specification Volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing PVC " P " or " S " trap for water closet (Squatting pan) ISI marked including jointing the trap with the pan & PVC pipe with approved adhesive etc. complete 110mm ( One hundred ten milimetre ) dia as per HP.PWD.,specification Volume-I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing Vitreous China wash down water closet ( European type W.C. pan ) with intergal " P " or " S " trap including jointing the trap with soil pipe in cement mortar 1 : 1 ( One cement : one sand ) ( Seat & cover to be measured & paid for separately ) Angle Indian Universal closet of white shade of Hindware or its equilevent W.C. Pan as per HP.PWD., specification Volume -I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of Engineer-in-Charge.

Providing & fixing PTMT coloured/ white automatic flushing cistern with a pair of PVC/C.I. or M.S. bracket complete with fittings including PVC syphonic apparatus, mosquito proof Lid. PVC union & coupling for connections with inlet, outlet and over flow pipe including cutting holes & making good the same ( Over flow pipe to be measured & paid for separately) 5.00 Litre ( five litre ) net capacity as per HP.PWD., specification Volume -I ( one )including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of Engineer-in-Charge.

Providing & fixing plastic seat ( solid/Hollow type ) & cover for wash down water closet with C.P. brass hinges & rubber buffers Solid Type white plastic seat & cover as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing vitreous China bowl pattern Urinal including connection the Urinal with waste pipe by means of white lead mixed with chopped hemp ( waste pipe to be measured & paid for separately ) Flat back type size 430mm x 260 mm x 350 mm ( Four hundred thirty milimetre into two hundred sixty milimetre into three hundred fifty milimetre ) size as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing C.P. brass flush pipe/ spreaders for urinal with fitting such as unions, clamps etc. ( all in C.P. brass ) including cutting holes & making good the same 15 mm ( fifteen milimetre )nominal size as per HP.PWD., specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing PTMT Jet spray of approved quality & colour with 1.50 ( One & five zero ) meter tube as per HPPWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing Vitreous China wash basin with single hole for pillar tap with C.I. Or M.S. brackets painted white including cutting holes & making good the same but excluding fitting flat back white shade No. 102012 of clear size 580 x 400mm ( five hundred eighty into four hundred milimetre ) with pedestal of Hindware or its equivelent as per HP.PWD.,specification Volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing vitreous China Pedestal for wash basin complete recessed at the back for reception of pipes & fittings as per HP.PWD.,specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing stainless steel kitchen sink of approved standard ISI marked No. 1250 D of size 470mm x 420mm x178mm with Double bowl steel Sink ISI Marked 304 grade, of Prayag polymers or its equivelent with cast iron or Mild steel brackets painted white including cutting holes and making good the same but excluding fittings as per HPPWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing C.P. brass chain 50 mm ( fifty milimeter ) long & rubber plug of following size for sink or wash basin 32 mm ( thirty two milimeter ) dia as per HPPWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing M.I. union for wash basin or sink 32mm ( Thirty two milimetre ) dia as per HP.PWD.,specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing C.P. brass waste for wash basin or sink 32mm ( Thirty two milimeter ) dia as per HP.PWD.,specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing C.P. brass" S "trap for wash basin or sink 32mm(Thirty two milimeter ) dia as per HP.PWD.,specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing 600mm x 450mm ( six hundred milimetre into for hundred fifty milimetre ) bevelled edge mirrior of superior glass mounted on 6mm (six milimeter ) thick A.C. sheet or plywood sheet & fixed to wooden plugs with C.P.brass screws & washers as per HP.PWD., specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing C.P. brass towel rain complete with C.P. brass brackets fixed to wooden plugs with C.P. brass screws 750mmx20mm ( Seven hundred fifty milimetre into twenty milimetre )as per HP.PWD.,specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing toilet paper holder, C.P. brass as per HP.PWD.,specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing P.V.C. connection with brass union ( a ) 300 x 450 mm ( Three hundred into four hundred fifty milimeter ) length 15 mm ( fifteen milimeter ) nominal bore as per HPPWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing brass bib tap ( superior or heavy type ) 15mm dia ( fifteen milimetre ) dia as per HP.PWD.,specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing 15mm ( fifteen milimeter ) mixer for kitchen sink with top/ bottom swinging soput of superior quality as per HPPWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & fixing C.P. brass pillar tap with capstan head 15mm dia ( fifteen milimeter ) dia as per HP.PWD.,specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing C.P. stop cock 15mm dia ( fifteen milimetre ) dia as as per HP.PWD., specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & fixing C.P. brass angle valve 15mm ( fifteen milimetre ) without nuts & pipe ( fifteen milimetre ) dia as per HP.PWD.,specification Volume-I (one) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-charge.

Providing & laying in trenches 150 mm ( One hundred fifty milimeter ) dia P.V.C. Finolex Type-B Spigot soaked waste and ventilators pipes including collers and fitting the joints with approved adhesive etc. complete as per HPPWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Providing & laying cement concrete 1 : 4 : 8 ( One cement : four sand : eight graded stone aggregate 40 mm ( forty milimeter ) nominal size ) for surround or in caring P.V.C. pipe of 150 mm ( One hundred fifty milimeter ) dia including necessary form work etc. complete as per HPPWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Cutting holes through existing brick work including making good the same in cement mortar 1 : 6 ( One cement : six sand ) per centimeter depth of cutting holes upto and including 400 Sqmt ( Four hundred square centimeter ) in area as per HPPWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Cutting holes upto 15 cm x 15 cm ( fifteen centimeter into fifteen centimeter ) in R.C.C. floors and roofs for passing drain pipe etc. & repairing the holes after insertion of drain pipe etc. with cement concrete 1 : 2 : 4 ( One cement : two sand : four graded stone aggregate 20 mm ( twenty milimeter ) nominal size ) including finishing complete so as to make it leak proof as per HPPWD., specification volume-I ( one ) including carriage of all labour equipment & materials to various location through all leads,lifts & other incidental charges complete as per entire satisfaction of the Engineer-in-Charge.

Constructing manhole with R.C.C top slab in 1:2:4 mix in 1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) foundation concrete1:4:8 (1cement : 4 sand : 8 graded stone aggregate 40mm nominal size) inside plastering 15mm thick with cement mortar 1:3 (1cement 3 sand) finished with a floating coat of neat cement and making channels in concrete 1:2:4 mix (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) finished smooth complete. Inside size 800mm x 800mm and 500mm deep including precast RCC cover with frame for 455 mmx610mm internal dimensions of man hole complete with 200mm thick walls of brick masonry using common burnt clay building bricks in cement mortar 1:3 (1 cement : 3 sand) complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing precast RCC cover with frame for 455 mmx610mm internal dimensions of man hole complete including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing precast RCC cover with frame for 300 mmx300mm internal dimensions of gully trap complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportation within all leads and lifts and as per direction of Engineer-in- Charge.

Supplying and filling brick bats in soak pit/filter tank as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts

ARVIND KUMAR BANSAL

NARESH KUMAR TULI