COMPREHENSIVE REPAIR TO OTM ACCN of CSR AT YOL CANTT UNDER AGE B/R-II AREA AT YOL CANTT.

Amount

PART-I:-Dismantling plain or corrugated steel sheeting any gauge, thickness including Nainital or similar pattern roof covering, all as specified.

Dismantling wall and ceiling boards (fiber, pulp, insulation etc) or insulation boards/ slabs/ blankets, any thickness including cover fillets in ceiling, all as specified.

Demolition of stones or brick masonry or block walling, built in cement mortar including all quoins, arches etc., but excluding ashlar facing, dressed stone work etc.complete, all as specified and as directed.

Taking up or down 15mm bore, steel tubing and connections, including cleaning for refixing or removal from site, all as specified.

Taking up or down 20mm bore, steel tubing and connections, including cleaning for refixing or removal from site, all as specified.

Taking down cement plaster on brick or stone walls, ceiling, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete, all as specified and as directed.

Taking down shutters of any description exc. 1 Sqm not exc. 2 Sqm each and removing from site, all as specified.

Taking down shutters of any description not exc. 1 Sqm each and removing from site, all as specified.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) not exc. 1.5 Sqm each and removing from site, all as specified.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) exc. 1.5 Sqm but not exc. 4 Sqm each and removing from site, all as specified.

Dismantling timber scantlings 40 sq. cm and over in section, in any position, framed work, complete all as specified.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames, steel or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete, all as specified

Hacking out old broken glass (any thickness, size, quality or description)metal frames, steel or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete, all as specified

Mat finish joint less (non skid), Premium class I grade, coloured, ceramic tiles, 7 to 8mm thick (Square/ rectangular) area of each tile exc. 0.06Sqm but not exc. 0.11 Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:6 (1 cement : 6 coarse sand) complete, all as specified.

Mat finish joint less (non skid), Premium class I grade, coloured, ceramic tiles, 7 to 8mm thick (Square/ rectangular) area of each tile exc. 0.18Sqm but not exc. 0.38 Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:6 (1 cement : 6 coarse sand) complete, all as specified.

Glazed coloured tiles of size 350x250/450x350x7mm thick as in vertical surfaces such as jointed in neat cement slurry and pointed with coloured cement to match and including 10mm thick plastering in cement mortar 1:4 (1 cement : 4 coarse sand) complete, all as specified.

Machine cut kota stone slab flooring 18-20 mm thick of size not less than 550 mm X 550 mm as per sample kept in GE’s office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, as in floor etc, laid over and including 15mm screed layer in cement mortar 1:6 (1 cement : 6 coarse sand), cutting, rubbing, grinding and polishing to achieve mirror finish complete, all as specified.

Machine cut kota stone slab 18-20 mm thick as per sample kept in GE’s office, as in vertical surfaces such as skirting/dado/riser to steps laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, laid over and including 10mm thick plastering in cement mortar 1:4 (1 cement : 4 coarse sand) including cutting, rubbing, grinding and polishing to achieve mirror finish complete, all as specified.

75mm thick Plain cement concrete M-7.5 nominal mix, D-2, using 40mm graded mechanically crushed stone aggregate as in sub base complete all as specified.

Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment laid over and including 50mm thick sand cushion, joints of tiles filled with dry sand and compacted with mechanical vibrator complete all as specified and directed.

Plain cement concrete M-15, nominal mix, type B-0, using 12.5mm graded mechanically crushed stone aggregate as in floors, 25mm thick, surface finished even and fair to receive top surface, all as specified.

Plain cement concrete M-10, nominal mix, type C-1, using 20mm graded mechanically crushed stone aggregate, 50mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified. Note:- The unit rate include for use of form work (straight or curved).

Rendering cement plaster 15mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) on fair faces of brick wall or concrete surfaces, surface finished even and smooth without using extra cement with WPC , all as specified. Note :- water proofing compound shall be measured and paid separately

Rendering plaster 15mm thick in cement mortar 1:6 (1 cement :6 coarse sand) on other than fair faces of brick wall or stone wall surfaces, surface finished even and smooth without using extra cement, all as specified.

Rendering cement plaster 10mm thick in cement mortar 1:3 (1 cement : 3 coarse sand) on ceiling, surface finished even and smooth without using extra cement, all as specified.

Two coats of cement base paint on newly plastered surface of wall including preparation of surface complete all as specified and directed.

Preparation of newly plastered wall surfaces and applying two coats of oil bound distemper over 2mm thick wall care putty complete, all as specified.

Three coats of white wash on newly plastered or previously undecorated surfaces of wall including preparation of surfaces complete, all as specified.

Three coats of white wash on newly plastered or previously undecorated surfaces of ceiling including preparation of surfaces complete, all as specified.

6mm thick non asbestos fiber cement building boards (Decorative E Board) as in ceiling fixed or laid/ inserted to timber/GI / aluminium framework fixed with nails, complete,all as specified.

Aluminium anodized snap grid frame work of size 605 mm x 605 mm as in false ceiling, flat or sloping (pattern as per manufacturer's catalogue/instruction), cutting holes for electrical fittings fixed on an including aluminium tee of size 25 mm x25 mm x1.5 mm as main runner, aluminium tee of size 25mmx25mmx1.25mm as cross runner and aluminium angle of size 25mmx25mmx1.25mm at the perimeter suspended from soffit at approx 900mm centre to centre with hangers 6mm dia galvanized (length as per site requirement) adjusting level fixed to roof by means of ceiling cleats made out of galvanized iron flat 40mmx3mm size, 60mm long and expansion hold fasteners 12.5mm dia, 40mm long including necessary scaffolding all as specified and directed.

Rolled Mild steel sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc. similar work conforming to Fe.290. Gde-E-165, all as specified and directed.

Factory made 2nd class hard wood (Sal/ Hollock) plain, framed, panelled 35mm thick shutters without interlocking rail and with one paneland panels of 9mm BWP commercial plywood or 12mm veneered particle with commercial face veneers on both sides.The size of rail and style as per IS–1003 (Part-I), kiln seasoned and chemically pressure treated, all as specified.

Factory made second class hard wood (Sal) glazed and Skelton door shutters 35mm thick open rebated and prepared to receive glass gauge etc (without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitered beads for securing glass or gauge etc., size of members of shutter as specified in clause 8.24 (a) of part-I, fitted to chowkats, complete all as specified.

Factory made second class hard wood (Sal) glazed and Skelton door shutters 25mm thick open rebated and prepared to receive glass gauge etc (without sash bars) edges but divided into squares, of framing plain chamfered or rounded fitted with cut and mitered beads for securing glass or gauge etc., size of members of shutter as specified in clause 8.24 (b) of part-I, fitted to chowkats, complete all as specified.

Factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing on page No 180 of MES SSR 2020 Part-II

Factory made fully glazed PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; completespecified and directed. Note:- Glass shall be measured and paid separately

Factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam PVC sheet and edges shall be painted to match with prelam sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing on page No 176- of MES SSR 2020 Part-II

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of 5 mm thick plain coloured PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site, Sheet No 1/1) specified and directed.

Supply only integral water proofing compound (ISI marked) or approved brand.

Steel window 1.25mm thick box type (Primer coated) ERW hollow P section of size 85mm x 35mm double rebated comprises gauged, glazed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with two openable leaf consiting two Nos sash bar of T-Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 30mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC M-15, type B-0 (04 No's for each window, steel duly painted with one shop coat of zinc chromate primer on prepared surfaces) and finishing the surfaces to match with existing including following fitting welded to frame shutter:-(i) Hold fast, 150mm long of 12mm x 3mm made to shape -04 Nos per window.(ii) Handle of Z section 20mm x 25mm, 100mm long -1 No per leaf.(iii) MS tower bolt 150mm long - 2 No per leaf(iv) Z section 20mm x25mm, 100 long stopper - 1 No per leaf.(v) Cleat 65mm long of hollow square 15mm x 20mm x 63mm welded to hinge -1 No per leaf.(vi) Mild steel pintle hinge of size 75mm x 12mm - 2 Nos per leaf.(vii) Flat iron fillets of size 20X3 mm for fixing wire gauge.(viii) Fabrication & fixing arrangement as per drg No. CEPZ/ TD 06/07.Make : As per Appendix 'C'.Note:-(i) Above referred drawing has not been made part of tender. The same can be seen in the office of GE during working hours on any working day.

Natural colour 15 micron anodized aluminium door chowkhat with shutter of approved design complete with all fixing arrangements including providing and fixing door handles, tower bolts, hydraullic door closer and mortice lock, hinges, door stopper including neoprene lining. The member shall made out of extruded aluminium sections comprising of:- a) Shutter vertical member 85.00 x 44.45 x 1.80mm weighing 1.302 Kg/RM. b) Shutter top member 83.5 x 44.45 x 1.70 mm weighing 1.243 Kg/RM. c) Shutter bottom member 114.30 x 44.45 x 1.29mm weighing 1.139 Kg/RM. d) Shutter lock rail 83.5x44.45x1.70mm weighing 1.243 Kg/RM. e) Anodised aluminium handle, fancy type, 350mm long and aluminium tower bolt of size 150mm. (f) 5.50mm thick tinted sheet glass fixed with alumnium beading, silicon lining and gaskets. (g) Aluminium anodised frame of door of section 101.6 x 44.45 x 1.75mm weighing 1.367 Kg/M, with flat iron hold fasts and necessary concrete to fix hold fasts all as directed. Note:- (i) Shutter shall be fixed with heavy floor spring ISI marked and pivot, brass lock with duplicate keys.

Natural colour 15 micron anodized aluminium window chowkhat with shutter of approved design complete with all fixing arrangements including providing and fixing door handles, tower bolts, hydraullic door closer and mortice lock, hinges, door stopper including neoprene lining. The member shall made out of extruded aluminium sections comprising of:- a) Shutter vertical member 47.62 x 45.45 x 1.74mm weighing 0.881Kg/RM. b) Shutter top member 47.62 x 44.45 x 1.1.14 mm weighing 0.607 Kg/RM. c) Shutter bottom member47.62 x 44.45 x 1.14mm weighing 0.607 Kg/RM. d) Natural colour 15 micr anodised aluminium anodised frame of chowkhat of section 85x44.45x1.80mm weighing 1.302 Kg/RM, with flat iron hold fasts and necessary concrete to fix hold fasts all as directed. (e) 5.50mm thick tinted sheet glass fixed with alumnium beading, silicon lining and gaskets.f) The size of Anodised aluminium round handle, fancy type shall be 100mm dia (02 Nos) and aluminium anodised aluminium tower bolt of size 100mm (02 Nos).

PCC M-15, nominal mix, B-1 using 20mm graded mechanically crushed stone aggregate as, in lintels up to 1.5 metre clear span cuts, steps seismic and other similar bends, coping, bands plates for serving hold fasts etc. and the like including weathering slighting rounded or chamfered angles and throating complete all as specified. Note:- (i) The unit rate include for use of form work (straight or curved). (ii) Reinforcement if any shall be measured and paid separately.

Mild steel work as in bolt hooks (stay) hook and pintle hinges, bands, straps, hold fasts, clamps, wall ties, cleats, fanhooks etc. or similar small articles conforming to grade Fe-290 grade E-165, all as specified.

Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed in repair with stainless steel wire staples or wooden beads, all as specified.

Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden beads, all as specified.

Sheet glass 4mm thick ordinary quality and glazing with oil putty wooden beads in squares, not exc. 0.5sqm in each pane, complete all as specified.

Figured glass, pin head type 4mm thick and glazing with oil putty/ wooden beads in squares, not exc. 0.5sqm in each pane, complete all as specified.

Aluminium anodised, (ISI marked), barrel tower bolts of extruded section, length of bolt 150mm , fixed ,all as specified.

Aluminium anodised, (ISI marked), barrel tower bolts of extruded section, length of bolt 100mm , fixed ,all as specified.

Extruded aluminium alloy handles, fabricated type, anodised, of size 150mm, all as specified.

Extruded aluminium alloy handles, fabricated type, anodised, of size 100mm, all as specified.

Butt hinges, medium weight, cold rolled, mild steel 100mm long, all as specified.

Butt hinges, medium weight, cold rolled, mild steel 75mm long, all as specified.

Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, length of bolt 250mm with lipping frame to match , all as specified.

Applying two coats of synthetic enamel paint over a coat of pink primer on new wood or wood based surfaces of any description, exc. 10cm width or girth including preparation of surfaces, all as specified.

Applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel or steel based surfaces of any description, exceeding 10cm width or girth including preparation of surfaces, all as specified.

Rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment etc. conforming to grade Fe 410 -W(Gde-E- 250 quality-A ) steel ,all as specified.

Rolled sections as in Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240s, steel workcomplete , all as specified.

Mild Steel framed work as Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment complete, conforming to Fe 290 Gde E-165 , all as specified.

Corrugated galvanized iron mild steel sheets 0.63mm thick, grade ‘O’, with 120 grams per square metre zinc coating fixed with 'J' or 'L' hook as in roof covering with two corrugation side lap. (Horizontal distance of side lap shall not be less than 145mm and depth of corrugation shall be 12.5mm), all as specified.

0.80 mm thick plain galvainsed mild steel sheeting in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete, all as specified.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.60mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.60mm thick of any colour having tensile strength of 550 Mpa as in ridge,hips, valley gutter and cladding to wall, fixed with self tapping screws as specified, all as specified and directed.

2nd class soft wood (Kail) as in scantling clean sawn timber fixed in framed including preparation and applying one coat of black bituminous paint complete, all as specified.

Fly ash brick work with old size bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 (1 cement : 6 coarse sand), complete all as specified.

Brick work with fly ash bricks, old size bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan exceeding 6m mean radius in half brick thick wall built in cement mortar 1:4 (1 cement : 4 coarse sand), complete all as specified.

Vitreous China wash down water closet (pedestal pattern), white fixed including traps, connection to drain or outgoing pipe, PVC 32mm dia flushing pipe, anti-syphonage pipe complete including fittings, PVC white seat cover and chromium plated jet including PVC valveless, syphonic action type flushing cistern 10 litres capacity low level with inlet, ball valve , float and handle with brackets , fixed complete ,fixed in repairs all as specified, Make as per Appx 'C'

Vitreous Chinaware squatting pan, ‘Orrisa pattern’ size 580 mm x 440 mm, crystal white, with cast iron ‘P’ or ‘S’ trap, front or back inlet, integral foot rest with provision of plain cement concrete M-15, type B-I using 20 mm graded crushed stone aggregate and PVC valveless, syphonic action type flushing cistern 10 litres capacity low level with inlet, ball valve , float and handle with brackets,32mm dia flushing pipe, anti-syphonage pipe completeincludingfittings,complete all as specified,3 connections to trap and to flush pipe, etc and making good to floors to match existing, in repair, all as specified. Make: as per Appx 'C'

Wash hand basins, Vitreous China of size 550mmx400mm, white with and including cutting for and pinning on ends of brackets, 450 mm long PVC connections 15mm size with PTMT coupling nuts at both ends, trap, grating and 32mm dia CP brass waste coupling, chain and plug and porcelain stopper, waste fittings such as 32mm dia flexible PVC waste pipe fixed, 15mm bore brass chromium plated fancy type pillar tap,screwed for iron pipe and fixed in repairs, complete all as specified,Make as per Appx 'C'

32mm bore High density polyethylene pipes (HDPE) of pressure rating 6 kgf/Sqcm fixe to wall etc including short lengths, with all pipe fittings uch as ends, elbows, unions, tees, reducing tees, adoptors, sockets, plugs, hose clips etc. and fixing to walls etc, complete with saddles (snap clips), wall clips, hooks, protective mild steel tube sleeves and cutting through walls, floors and their making good, complete all as specified.

Brass Chromium Plated, tubular towel rail, 20mm dia, D type, 60cm long between flanges, with brackets, fixed with chromium plated screws, fixed in repair, complete all as specified.

Mild steel galvanized iron water tubing 15mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor complete, all as specified and directed.

Mild steel galvanized iron water tubing 20mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor/ sunken floor spout complete, all as specified and directed.

Bib taps, 15mm bore, cast copper alloy with crutch or butterfly handle, chromium plated screwed for iron pipe or for brass ferrule and fixed in repair , all as specified.

Chromium plated brass shower rose, 125mm size suitable for 15mm bore pipe with swivel joint fixed in repair to pipe, complete all as specified.

Angle valve, cast copper alloy, fancy chromium plated, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed in repair complete, all as specified.

Brass Chromium Plated,health faucet suitable for 15mm bore pipe fixed in repair, complete all as specified.

Harrison 25mm bore Curtain rails, mild steel, chromium plated with fixing brackets, stops and roller etc. fixed in repair complete all as specified.

Rotational moulded polyethylene water storage tank 500 Ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position inbcluding PVC float ball valve 20mm dia epoxy coated aluminium rod with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line including dismantling old cemented/ asbestos water/ PVC storage tank, all as specified.

15mm Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed in repair ,complete all as specified.

20mm Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed in repair ,complete all as specified.

25mm Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed in repair ,complete all as specified.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall of bore 110mm including fixing adjustable clamps complete, complete, including taking up or down old pipe , all as specified.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall of bore 75mm including fixing adjustable clamps complete, including taking up or down old pipe , all as specified.

PVC (SWR) bends any radius, 110mm bore( fitted with oval access door, all as specified.

PVC (SWR) bends any radius, 75mm bore jointed with solvent cement( fitted with oval access door all as specified.

PVC (SWR) junction single, (Single T) equal or unequal, 110mm bore, provided with oval access door all as specified.

PVC (SWR) junction single, (Single T) equal or unequal, 75mm bore, provided with oval access door all as specified.

PVC (SWR) floor trap, plain with grating including jointing with solvent cement, dia of outlet 75mm, all as specified.

Sheet glass 5.5mm thick ordinary quality and glazing with glazing clips, ruber neoprene packing, aluminium beads in squares, not exc. 0.5sqm in each pane, complete all as specified.

Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor ,overall length of cover plate 150mm,fixed in repair complete all as specified.

Taking down aluminium door shutter n. exc 2 Sqm each, taking out servicable glass panes, hydraulic door clocer, but hinges, double action hydraulically regulated floor spring and other fittings, if required carefull and refixing in the same opening after repairs of unservicable or loosened joints/cleats of top rail/bottom rails/lock rails and styles etc and fixing old servacale glass, any thickness with rubber packing and aluminium beadings, fixing of old servicable hydraulic door closer, double action door spring duly oiling/greasing and fixing all servicable fitting complete all as directed by Engr-in-Charge. NOTE;- Unservicable door closer, double action floor spring, glass panes and other fittings etc shall be replaced and paid under separate items of schedule.

Mortice lock, brass, vertical type, size 100 mm, 4 lever, fixed in repair to aluminium door shutter, complete all as specified.

Aluminium (diecast) body door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed in repair,complete all as specified.

Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed in repair complete all as specified.

Mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/ or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed ballusters walk ways; railings; framework of water tanks and similar work conforming to Fe.290. Gde-E-165, all as specified.

VIJAY KUMAR LAKHNI

M/S VIG AND COMPANY