Construction of toilet block at F-4 and Store section inside factory at AFK.

M&L for providing Reinforced Cement Concrete M-20 grade (Design mix) 1:1.5:3 mix (20mm graded aggregate) in Foundation, including rafts, footing, foundation beams, plinth beams; bases for columns, etc basement slabs, under reamed piles and mass concrete etc complete.

M&L for providing Reinforced Cement Concrete M-20 grade (Design mix) 1:1.5:3 mix (20mm graded aggregate) in Columns,Pillars,piers,posts and struts etc.

M&L for deformed or twisted bars 10mm Dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

M&L for deformed or twisted bars 6 to 8mm Dia, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

M&L for providing formwork to sides of concrete foundations, footings, bases of columns, rafts and raft beams, sides and soffits (if any) of foundation and plinth beams and similar works, vertical or to batter rough finished surfaces of concrete flat.

M&L for providing formwork to sides of square, rectangular or polygonal pillars, posts, struts, piers, columns and stanctions for rough finished surface of concrete flat.

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finished surface of concrete flat.

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces in CM 1:4 including applying neeru finish to plastering as specified.

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces of ceiling in CM 1:4 including finishing the plastered surface even and smooth without using extra cement.

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces in CM 1:4 including finishing the plastered surface even and smooth without using extra cement.

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces of walls in CM 1:4 including finishing the plastered rough finish.

M&L for Glazed Ceramic coloured tiles in vertical suraces 300 x 200mm x 7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match. (Make- Johnson, Kajaria, Bell).

M&L for Granite (of any type) work (table rubbed and polished) 20mm thick for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.

Cutting holes into or through brick walls/ stone walls built in cement mortar and making good in cement mortar or cement concrete 1:2:4 Type B-1 as required for superficial area of hole not exceeding 150 sq cm.

M&L for providing precast cement concrete type B1, 1:2:4 (20mm graded aggregate) in drain cover slab and similar articles etc. set in cement mortar 1:4.

M&L for preparing plastered or unplastered new surfaces and applying two coats of white wash on ceiling.

M&L for preparing plastered or unplastered new surfaces and applying two coats of Dry distemper on walls.

M&L for preparing plastered or unplastered new surfaces and applying two coats of cement paint on walls.

M&L for providing WPT by using membrane over roof & vertical surface, consisting of applying oil bonded bituminous primer coat at 0.30 kg/m2 on a clean & dry surface & then providing a layer of APP modified membrane 3mm thick weighing approx. 4 kg /m2with non woven polyester reinforcement with very thin polyethylene film on both side with thermofusion process by gas regulated torch & finally applying one coat of super silver sheld aluminium based bituminous paint all as per specification & as directed by E-in-C. Make: Tiki, IWL or equivalent.

Supply and fixing of sheet metal enclosure, double door MCB DB (Distribution Board), single phase & neutral, 240 Volt, 4-way with 200 Amp rated bus bar. Make - Legrand/Indo Asian/Schneider/ABB/L&T only.

Supply and fixing of RCBO for Earth leakage, Overload & Short- Circuit Protection, Double Pole, 32 Amp, 30 mA, Type-A. Make - Legrand/Indo Asian/Schneider/ABB/L&T only.

Supply and fixing, 240V, 10 kA, 'C' curve MCB of Single Pole and current carrying capacity 6Amp to 32Amp in MCB DB complete with connection, testing and commissioning. Make - Legrand/Indo Asian/Schneider/ABB/L&T only.