Civil and Electrical works for the Renovation of HINDLABS Diagnostic Lab Facility at TRIDA, Medical College, Thiruvananthapuram

Amount

Civil works

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per directionof Engineer - in - charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Dismantling steel work in built up sections in angles, tees, flats, tubular sections and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.In cement mortar

Dismantling doors, windows and clerestory windows (steel or wood/ glass) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below

Dismantling aluminium/ Gypsum/ glass partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge.

Cleaning existing floor tile/Wall tile in neat and shiny by using stain remover /chemicals and clean water with due care and precaution, by mechanical / manual means ( using a rag or chamois-type mop rather than sponge mop), including preparing and cleaning the surface for re-pointing/refilling of joints, including disposal of rubbish to the dumping ground all complete.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double action hydraulic floor spring type fixing arrangement including stopper and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-incharge

Providing and fixing 12 mm thick frameless toughened glass partitions of approved brand and manufacture, including providing and fixing top & bottom patch fixing arrangement and making necessary holes etc. for fixing required partitions, all complete as per direction of Engineer-incharge

Providing and fixing SS H handle having min 45 cm length in toughed glass door including all necessary screws etc. complete.

Providing and fixing SS patch lock on toughed glass door including all necessary screws etc. complete.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion : Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately): Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing Pre-laminated (one side decorative and other side balancing lamination) flat pressed 3 layer or graded particle board (medium density) Grade I, Type II, IS :12823 marked, with necessary fixing arrangements and screws, including drilling necessary holes for rawl plugs etc. and priming coat on unexposed surface complete: 12 mm thick

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . With float glass panes of 8 mm thickness (weight not less than 20 kg/ sqm)

Providing and fixing wooden partition made of 12mm BWR ISI (303 Grade) plywood (Century, Greenply, Fineply or equivalent) with 1mm lamination at exposed area and 0.8mm inside laminate by Hot press Lamination (3m or Henkel) (Brand : MERINO, Associate or equivalent) of approved colour and pattern as per the design and direction of Engineer in charge. Partition top and side shall be provided with 16mm both side white laminated plywood (top side high glossy finish) with 1.3 mm thick glossy edge band. The frame work should be 16mm BWR grade plywood. All joints and necessary grooves in laminate to be given with smooth finish. the partition is firmly fixed to the floor and wall. Area of unit to be measured in elevation Only.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). Sal wood

Providing and fixing stain retardant cubicle curtains having net not less than 30 cm on the top and over all cloth height not less than 2.1 m using approved quality cloth(Rate Rs.300 per metre or above) which includes supplying of approved quality cloth, stitching ,fixing with all necessary fixing items including curtain road and other fixing arrangements all complete.

Providing and fixing chromium plated brass butt hinges with necessary chromium plated brass screws etc. complete. 125x70x4 mm (ordinary type)

Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer-incharge Powder coated minimum thickness 50 micron aluminium

Structural steel work in single section, fixed with or without connecting plate,including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete

Providing and fixing anchor bolts including nuts and washers complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Zebra Blinds: Providing and Fixing Zebra blinds for windows with approved colours as per Indian standards with following Specification Head Rail, Bottom Rail: Made of extruded aluminium powder-coated with high mechanical strength, UV resistant, anti-fogging polyester powders, expressly made for accessories to set inside IG units. Ladder Tape, Cords provided with 100% Polyester, Excellent dimensional stability and high mechanical & UV resistance. Modular and durable Chain for vertical movement.

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: One or more coats on old work

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Providing and fixing framed toughened automatic glass door of minimum 10mm thickness with all necessary fixing arrangemnts and proximity sesnors all complete Door of Size : 1200 X 2100

Reception "L" Shaped Table of size 3400mmx600mmx750mm Made of minimum 18mm BWR ISI (303 Grade) plywood (Century, Greenply, Fineply or equivalent). On top and all sides with 1mm thick hot press (3M or Henkel) laminates (Brand MERINO, Associates or equivalent) of approved colour and pattern as per the design. Table top shall be provided with 2mm thick edge band. The table is provided with 1 drawer, 2 Storage, 1 key board pullout with necessary hardware like flipbox for electrical and data sockets, multipurpose locks, handles, mini fix, dowels and screws. Exposed edges to be finished with 0.8 mm edge band as per specified colour. Front elevation of the table to be provided with backlit signages and to be done as per the design and instructions of the engineer in charge.

Reception "L" Shaped Table of size 6150mmx600mmx750mm Made of minimum 18mm BWR ISI (303 Grade) plywood (Century, Greenply, Fineply or equivalent). On top and all sides with 1mm thick hot press (3M or Henkel) laminates (Brand MERINO, Associates or equivalent) of approved colour and pattern as per the design. Table top shall be provided with 2mm thick edge band. The table is provided with 3 drawer with cash till, 4 Storage, 2 key board pullout with necessary hardware like flipbox for electrical and data sockets, multipurpose locks, handles, mini fix, dowels and screws. Exposed edges to be finished with 0.8 mm edge band as per specified colour. Front elevation of the table to be provided with backlit signages and to be done as per the design and instructions of the engineer in charge.

Work Station Table of size 1000x600mmx750mm Made of minimum 18mm thick Medium Denisty Fiber Board with lamination of approved colour and design. The table is provided with 1 drawer, 1 Storage, 1 key board pullout with necessary hardware like flip box, multipurpose locks, handles, mini fix, dowels and screws. Exposed edges shall be provided with minimum 1 mm thick edge band as per specified colour.

Supply and Installation of Slotted Angle Racks (Min size of rack 900mm Length X 300mm Depth X 2000mm Height): Supply and erection of Powder coated slotted angle metallic rack having min 8 shelves made up of min 40X 40 X 2 mm size rolled steel angle posts shall have 8 –mm diameter holes provided at 50- mm centre to centre. Metal shelves shall be made from mild steel sheets not less than 1.0 mm in thickness and with sufficient stiffeners. Shelves shall have lipped flanges. Width of flange being 30 mm and depth of lip 15 mm.

Supply and Installation of Slotted Angle Racks (Min size of rack 1300 mm Length X 300mm Depth X 2000mm Height): Supply and erection of Powder coated slotted angle metallic rack having min 8 shelves made up of min 40X 40 X 2 mm size rolled steel angle posts shall have 8 –mm diameter holes provided at 50- mm centre to centre. Metal shelves shall be made from mild steel sheets not less than 1.0 mm in thickness and with sufficient stiffeners. Shelves shall have lipped flanges. Width of flange being 30 mm and depth of lip 15 mm.

Supply and installation of size 1200mmx600mmx750mm Made of minimum 18mm thick Medium Denisty Fiber Board with lamination of approved colour and design. Exposed edges shall be provided with minimum 1 mm thick edge band as per specified colour.

Supply and installation of size 800 mmx600mmx750mm Made of minimum 18mm thick Medium Denisty Fiber Board with lamination of approved colour and design. Exposed edges shall be provided with minimum 1 mm thick edge band as per specified colour.

Supply of Fowler Bed with Mattress & Cushion (for Hospital Purpose) having Top flat platform made of perforated CRC sheet of thickness of 16G or better. Bed frame must be sturdy and stable to support weight of at least 170 kg. The frame structure should be made up of at least 16 G CRC, rectangular / circular pipe of 100 mm x 30 mm and mounted on trolley base made up of 100mmx30mm CR C rectangular pipe of 16 gauge. All adjustments for fowler position must be obtained from crank shaft, manually operated with stainless steel/ABS foldable handle on both the shaft. Fowler bed should be of following dimension: Mattress area of Length 2000 to 2010 mm x Width 900 to 1000mm x Height: - 500 to 550mm (without mattress). The finished bed must be rust proof, pre-treated and polished Stainless Steel. The bed should have telescopic side rails of stainless steel of 22 Gauze with spring loaded locking arrangement on both sides. Should have easily removable head and foot panels made up of ABS plastic. Should have strong & good quality single wheeled total locking type Swivel Castors of 125 to 150 mm diameter with breaks on all four castors for stabilized position. There should be suitable buffer mechanism to avoid hitting of the bed to the wall from all sides. Should have provision of fixing suitable rod for hanging intravenous / irrigation fluid bottle on both sides at head end and foot end. Each bed should be supplied with 1 no. good quality I. V. rod. Should have hooks on bed frame on both side for holding urine / drainage bag (at least 2 Nos. on each side). Hooks should be in-turned to prevent injury to bystander. Bed production facility to be US FDA registered. Bed to be European CE and facility to be ISO 9001, 14001 and 13485 approved. Mattress to be four sectional and to be combination of good quality foam and coir layer and exactly fitting to the bed.

Consultation Table of size 1200x600mmx750mm Made of minimum 18mm thick Medium Denisty Fiber Board with lamination of approved colour and design. The table is provided with 1 drawer, 1 Storage, 1 key board pullout with necessary hardware like flip box, multipurpose locks, handles, mini fix, dowels and screws. Exposed edges shall be provided with minimum 1 mm thick edge band as per specified colour.

Executive Chair: Medium back ergonomic chair with five nos. star shaped Nylon base. Castor: 50mm diameter nylon twin wheel, gas lift height adjustment, back angle adjustment and backrest height adjustment. Fixed armrest providing natural resting for arms. Seat with PU cutted foam backed fabric, back rest with mesh type fabric, upholstery: Heavy duty rubber backed fabric in BLACK.

Visitors Chair: Non-revolving executive chair with fixed armrest providing natural resting for arms. Seat with PU cutted foam backed fabric, back rest with mesh type fabric, Upholstery: Heavy duty rubber backed fabric in BLACK

Supply and errection of Airport type 3 seater waiting chair with powder coated chromium finish having minimum dimensions 1675mm legth X 710mm width X 775mm total height and 400mm seat height .Seat: Made of high quaulity foam that is covered with a soft and durable resin of approved shade supported over High quality cold rolled 1.2mm thick steel perforated sheet pressed and welded to form the shape.Arm & Leg: High quality 1.2mm thick MS Tube / Sheet .Cross bar: High quality cold rolled 2mm thick steel sheet pressed and welded to form the shape.

Vinly stickering over toughened glass with suitable design or pattern as per the instructions of engineer in charge.

Supplying and Installation of Frosted filim over toughened glass partition

Supply and installation of a hospital trolley of 75x45x90 cm made of SS 304 having 2 shelves with 3 Side Railing on top and bottom shelves. Trolley to be provided with sufficient provision for movement with lockable castors.

Supply and installation of a queue manager with minimum pole height of 80cm made of Stainless Steel. Length of ribbon should be a minimum of 250cm long of velvet finish

Providing and fixing of 3 mm thick Aluminum composite panel of approved make and colour as two nos of ACP in a single opening by fixing decorative face of ACP to the visible area in the aluminium partition including making provisions holes for fixing of , the cost of EPDM rubber / neoprene gasket etc all as per the instructions of Engineer in charge. ACP make: Armstrong or equivalent.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering.All works upto five floors. 1:4:8

Dismantling tile work in floors and roofs laid in cement mortars including stacking materials with in 50 metrea lead.

Electrical Works

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVCinsulated copper conductor single core cable in surface / recessed medium class PVC conduit,with modular switch,modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLSPVC insulated copper conductor single core cable etc as required.Group C

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2x1.5 sq.mm + 1x1.5 sq.mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 4sq. mm + 1 X 4 sq. mm earth wire.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 6Sq.mm + 1 x 6 sq.mm earth wire

Rewiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable and 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable as earth wire in existing surface/ recessed steel/PVC conduit including dismantling as required.Group C

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or inrecess,including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 ampsmodular switch,connection etc. as required. (For light plugs to be used in non residentialbuildings)

Supplying and fixing suitable size PVC box with modular plate and cover in front on surface or in recess,including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch,connection etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden blockincluding connection etc as required.

Supplying and fixing brass batten/ angle holder including connection etc. as required.

Supply and fixing 25 mm PVC casing capping as required.

Supply and fixing of 150MM PVC casing capping.

Supply, conveyance and Installation of compact Surface or Recess mounted, 15cm x 15cm, 15W LED luminaire with High translucent diffuser gives soft glare free, Cool White light & complete with electronic driver including all required mounting accessories, frames, along with dismantling/cutting false ceiling and making good the damages as required complete ( Make: <br>Philips/WIPRO/Havells or equivalent).

Supply, conveyance and Installation of compact Surface or Recess mounted, 60cm x 60cm, 36W LEDluminaire with High transculent diffuser gives soft glare free, Cool White light & complete with electronic driver including all required mounting accessories, frames, along with dismantling/cutting false ceiling and making good the damages as required complete. (Philips/WIPRO/Havells or equivalent)

Supplying, conveyance and Installation of 3 blade, 400 mm sweep, 1400 rpm Wall Mount Fan including frames and all mounting accessories complete. Recommended Make: USHA/ Havells/ Bajaj / Almonard or equivalent

Supplying, conveyance and Installation of 3 blade, 305 mm sweep, 1400 rpm Exhaust Fan including frames and all mounting accessories complete. Recommended Make: USHA/ Havells/ Bajaj or equivalent.

Supply, conveyance and Installation of compact, 20 W LED tube light with 1800 lumen giving soft glare free light including all required mounting accessories, frames complete. (Philips/WIPRO/Havells or equivalent)

Supply and Installation of 9-12 watt LED bulb in Existing Holder

Supplying and drawn of UTP 4 pair CAT 6 LAN cable in the existing surface/recessed steel/PVC conduit as required1 run of Cable

Supplying and fixing RJ45 Outlet including cover plate, Keystone Jack and Gang box supporting,connection etc. as required

Supply of 8 ports Network Switch, Rack-mountable 10/100/1000 Mbps, Switching capacity 35.7 Mbps Features: Flow control, Layer 2 switching, auto-negotiation, auto-uplink (auto MDI/MDI-X), Weighted Round Robin (WRR) queuing, Quality of Service (QoS) Power: AC 120/230 V (50/60 Hz) complete. Make D-Link/TP Link/Cisco or equivalent<br>

Supply and fixing of 4U wall mounting rack with supply and fixing of mounting brackets for support Lockable Front Door and Detachable Side Doors, Cable Manager and PDU of 4 or 6 sockets including cooling fan with accessories complete

Supply, Conveyance and Installing of 2MP IP Dome/Bullet Camera having 1/3" Progressive Scan True Day and Night Colour IR Camera having effective pixel of 2 MP, Video frame rate of 2MP @30FPS,Minimum illumination of 0.01 [email protected], 0 lux@IR On, 20 M IR Range, 24 IR LED, AWB, AGC, BLC, 2D Noise reduction, with 3.6mm board lense, 12 VDC, PoE IP67 rated weatherproof performance. 1 year warranty. Make: Bosch/CP Plus/Honeywell or equivalent

Supply and Installation of 600VA UPS including all accessories complete. Make: V-Guard/Luminous orequivalent

Supply and Installation of 2 TB Hard Disk Make: WD/Seagate or equivalent

Supply and Installation of LED Color Monitor of minimum 32 inch screen, complete, UHD display Make:LG/Samsung/Panasonic or equivalent.

Supply and Installation of wireless Mouse. Make : hp/ Logitech/dell or equivalent

Supply and Installation of Network Switch. 8 Port PoE Switch 1000BASE-T Copper Ethernet PoE+connections, 10M/100M/1G RJ-45 copper ports, 1000BASE-X Fiber SFP ports, 8 port Auto sensing 10/100/1000 Mbps PoE, minimum CPU memory 512 MB with 2 SFP/combo ports, Energy Efficient Ethernet (IEEE 802.3az). Make: Cisco/CP Plus/Netgear or equivalent.

Supply, Installation and Integration of 8 channel embedded Linux PoE, NVR (Network Video Recorder),having dual core embedded processor, must connect 8 channel IP cameras , should support min 5 SATA HDD each of 2TB and must record video simulataneously, (Recording Type: Continuous, Motion Detection, Alarm, Smart Event, Event Motion Detection, Alarm, Smart Event), Video Compression H.265(HEVC)/H.264+/H.264, 2 Year Warranty, Image quality should be maintained throughout the warranty period. Make: Bosch/CP Plus/Honeywell or equivalent

Supply and connecting 2 mtr long CAT6 cable Patch cord having RJ45 connectors crimped at both ends,to the existing outlets as required. Make: D-Link/TP-Link or equivalent.

Supply and fixing of 4U wall mounting rack with supply and fixing of mounting brackets for support Lockable Front Door and Detachable Side Doors, Cable Manager and PDU of 4 or 6 sockets including cooling fan with accessories complete

Supplying and drawn of UTP 4 pair CAT 6 LAN cable in the existing surface/recessed steel/PVC conduit as required1 run of Cable.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20mm

Supply,Installation,Testing and Commissioning of Response Indicator for all detectors above false ceiling.

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as required. 8 zone Panel

Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement,mounted in M.S. box (16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required.

Supply and Installation of Manual Call Point break glass type red colour powder coated MS/ABS box fix on existing wall /frame,24/12 Volt DC operated push OFF/ON switching mechanism with inner, outer frame, operation label and necessary attachments.

Supplying, installation, testing & commissioning of smoke detector with built-in LED and mounting base complete with all connections etc. as required.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V,on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar,interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator12 way, Double door

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.2 core 10 sq mm with factory made clamp

Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.2 core 16 sq mm with factory made clamp

Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required4.00 mm copper conductor ( 8 SWG)

Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.4.00 mm (8 SWG)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.2 X 10 sq. mm (19mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.2 X 16 sq. mm (22mm)

Supply, installation, testing and commissioning of Split Air Conditioner of following capacity and specifications: Consisting of high wall-mounted type room unit (fan coil) with cordless remote control and one number outdoor condensing unit comprising of energy-efficient suitable rotary compressor for operation on single-phase, 230 V, 50Hz supply, fixing the outdoor unit on a raised platform as per manufacturers recommendation and fixing of room (fan coil) unit on wall, standard 4 m distance refrigerant copper piping with 13mm nitrile rubber insulation, providing and making interconnection between room & condenser as per site conditions, comprising of 1" dia drain PVC pipe with insulation up to 4 m, canvas connections, full electrical cabling from power plug near indoor unit and to outdoor unit,ODU MS stand, first charge refrigerant gas, suitable stabilizer etc complete as required. (Make: Voltas,Blue Star, Hitachi, Carrier or equivalent). 2 TR 3 Star rated (inverter type AC) as per BEE

Supply, installation, testing and commissioning of Split Air Conditioner of following capacity and specifications: Consisting of high wall-mounted type room unit (fan coil) with cordless remote control andone number outdoor condensing unit comprising of energy-efficient suitable rotary compressor foroperation on single-phase, 230 V, 50Hz supply, fixing the outdoor unit on a raised platform as permanufacturers recommendation and fixing of room (fan coil) unit on wall, standard 4 m distance refrigerant copper piping with 13mm nitrile rubber insulation, providing and making interconnectionbetween room & condenser as per site conditions, comprising of 1" dia drain PVC pipe with insulation upto 4 m, canvas connections, full electrical cabling from power plug near indoor unit and to outdoor unit, ODU MS stand, first charge refrigerant gas, suitable stabilizer etc complete as required. (Make: Voltas, Blue Star, Hitachi, Carrier or equivalent). 1.5 TR 3 Star rated (inverter type AC) as per BEE

Supplying additional copper piping of required size and connecting the same to the available piping and extension of the same through PVC duct inside false ceiling

Supply, installation, testing and commissioning of drain piping of hard PVC pipe and fittings, insulated with '12 mm thick nitrite rubber 25 mm

Supply installatron, testing and commlssioning of drain piping of hard PVC pipe and fittings insulated with 12 mm thick nitrile rubber 32 mm

Supply installatron of LED strip with accessories cove light, making necessary cuttings and connections and fixing on false ceiling as directed by engineer in charge .Make -Philips, Wipro, Panasonic, Crompton.

MASTERCELL TELECOM SERVICES (P) LTD

panwar construction company