Construction of office building of newly created Division Jaswan Pragpur in Sub Tehsil Pragpur Distt. Kangra

Amount

Excavation in foundations and trenches (for pipes and pits in all depths etc.) in all lifts and in all kinds of soils such as pick work, jumper work, blasting in soft/hard rock, chiseling/wedging out of rock (where blasting is prohibited)and saturated soils, stacking the excavated earth within all leads and lifts, clear from the edge of excavation and then returning the stacked soil in 15 cm layers when required into plinths, sides of foundation and trenches etc., consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed by Engineer-in-charge within all leads and lifts

Providing and laying cement concrete 1:4:8 (1cement : 4 approved sand : 8 approved quarry stone aggregate.40mm nominal size) and curing complete excluding cost of form work in foundation and plinth including carriage of material within all leads and lifts.

Providing and laying reinforced cement concrete work 1:1.5:3 (1cement : 1.5 approved sand : 3 approved quarry stone aggregate.20mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced cement concrete work including carriage of material within all leads and lifts. Foundation footings basis of columns and the like and mass concrete .

Columns,pillers, posts & struts etc .

Suspended floor roofs landing and shalves and their supports balconies, beams, garders,bressumers and cantilevers upto floor two level.

Staircases ( except spril stair cases ) excluding landing but including preparing of the surface and finishing of nosing upto floor two level.

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm, so as to give a fair finish including centring, shuttering , strutting and propping etc. with wooden battens and ballies height of propping and centering below supporting floor to ceiling not exceeding 4meters and removal of the same for insitu reinforced concrete and plain within all leads and lifts. In foundation, footings, bases of columns etc. and mass concrete.

Columns,pillers, posts & struts etc .

Flat surfaces such as soffits and suspended floors, roofs landing and the like: Fliirs etc. upto 200mm in thickeness.

Staircase with sloping or stepped soffits including riser and stringers excluding landing.

Sides and soffits of beams, beam haunchings,contiliver girders, bressumers and lintels not exceeding 1 Metre in depth:

Edges of slabs and breaks in floors and walls under 20cm wide.

Vertical surface such as walls (any thickness) partitions and the like including attached pillasters,buttresses, plinth and string courses etc. and the like within all leads and lifts.

Providing tor steel reinforcement for RCC work including bending binding and placing in position complete upto floor two level. Tor steel.

1st Class Brick work using common burnt clay building bricks in foundation and plinths in cement mortar 1:6 (1cement :6 approved sand) including carriage of materials within all leads and lifts.

Half brick masonry in comon burnt clay building bricks in cement mortar 1:4 ( 1cement : 4 approved sand) including carriage of of all material within all leads and lifts above floor two level.

Providing and fixing anodised aluminium work for door, window, ventilators and partitions with extruded built up standard tubular and other sections of approved make conforming to IS 733 and IS 1285 anodised transparent or dyed to required shade according to IS 1868 (Minimum anodic coating of grade AC15) fixed with rawlpluge and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rustfree, straight, mitred and jointed mechanically where ever required including cleast angle, aluminium, snap beading for glazinge/panelling C.P. brass/stainless steel screws. All complete as per architectural drawings and the directions of Engineer-in-Charge. For doors, Windows and ventilatiors and glazed partitions frames. For door,windows, frames

For Shuters of doors, window (Schedule item)

Providing and fixing glazing in aluminium door, window, ventilators shutters and partitions etc. with PVC/neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-Charge. (cost of aluminium snap beading shall be paid in basic item.) glazing with glass panes of 4mm thickness (weight not less than 10.00 ks/sqm.

Providing and fixing 12mm thick prelaminated board both side bwp phenol bonded exterior/interior grade shutters with frame of 1st class deodar wood for cup board including nickel plasted bright finished piano hinges-25mm thick.

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm and braced with flat iron diagonals 20x5mm size with top and bottom rails of T.iron 40x40x6mm with 38mm dia steel pulley complete with bolts and nuts locking arrangements, stoppers, handles including applying a priming coat of red lead paint.

15mm cement plaster in single coat on fair side of brick masonery for interior plastering upto floor two level including arrises , internal rounded angle , chamfers and /or orunded angle not exceeding 80mm in girth and finished even and smooth in CM 1:3 (1cement: 3 approved sand).

20mm cement plaster in single coat on fair side of brick masonery for interior plastering upto floor two level including arrises , internal rounded angle , chamfers and /or orunded angle not exceeding 80mm in girth and finished even and smooth in CM 1:6 (1cement: 6approved sand)

Providing and laying cement concrete flooring 1:2:4 (1cement :2sand :4 graded stone aggregate 20mm nominal size) laid in one layer finished with a floating coat of a neat cement 40mm thick.

Providing and laying cement plaster skirting upto 30cm height with cement morter 1:3 (1cement :3approved sand) finished with a floating coat of neat cement including rounding of junction with floor with 15mm thick.

Providing and laying 40mm thick kota stone flooring 20mm (average) thick base of cement mortar 1:4 (1cement:4approved sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete.

Providing and laying Duro stone vetrified tiles (30x30x8mm) in grey/coloured of required shade in skirting risers of steps and dados on 12mm thick cement mortar 1:3 (1cement:3approved sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete.

Providing and fixing 10mm thick anti skid water proof stain and impect resistent heavy duty vetrified tiles Nitco or equivalent 600x600x10mm manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1cement:3approved sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete.

White glazed tiles 6mm thick in skirting risers of steps and dado 12mm thick / stone cladding cement mortar 1:3 (1cement:3approved sand) with cement slurry complete within all leads and lift Engineer in charge.

Providing and fixing anodized aluminium sliding door bolts anodized colour and shade with bolts and nuts screws 256 x16 mm etc. complete.

Providing and fixing anodized aluminium Tower bolts(barral type) anodized transparent or die to required shade and colour with screws etc. complete. 200 x 10 milimetre

150 x 10 milimetre

Providing and fixing aluminium handles anodized transparent or die to required colour of shade with necessary screws etc. complete. Handles 125 milimetre.

Handles 100 milimetre.

Providing and fixing Door closer for doors complete in all respect.

Providing and fixing of Blind/pauvers complete in all respect. Vista make

Providing and fixing aluminium eyes & hooks anodized transparent or dyed to required colour of shade with necessary screws etc. complete 150mm.

Providing and laying cement concrete 1:6:12 (1cement : 6 approved sand : 12 approved quarry stone aggregate.40mm nominal size) and curing complete excluding cost of form work in foundation and plinth including carriage of material within all leads and lifts.

Steel work welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and playing a priming coat of red lead paint, In beams joints channels, angles, tee, flats with connecting plates or angle cleats as in main and cross beams hip and jack rafters, purlins connacted to common rafters and the like within all leads and lifts.

Providing and fixing Pre-painted steel sheet 0.60mm thick.

Providing and fixing Pre-painted steel sheet ridges or hips 60cm. Overall 0.60mm thick.

Providing and fixing 12mm thick and 10mm wide palmet with 25mm diameter wooden curtain rod and brackets including fixing with 25x3mm M.S. flat 10cm long and plugs etc. complate 2nd class Indian teak wood.

Providing and fixing 75x60mm rounded hand rails in straight length complate in 2nd class Indian teak wood.

Providing plinth protection 50mm thick in cement concrete 1:3:6 (1cement:3sand: 6 graded stone agg. 20mm nominal size.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete.

Wall Painting (two coats) with plastic emulsion paint of approved brand and manufacture on undecorated wall urfaces to give an even shade including thoroughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth including applying of putty as required for making the surface.

Distempering( two coats) with oil bond washable distemper of approved brand and manufacture and of required shade on undecorated wall surface to give and even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar dropping and other foreign matter and also including preparing the surface even and sand papered smooth priming coat with distemper primer.

Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on coats to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered.

Providing and laying heavy duty precast cement concrete inter locking paver blocks vibro compacted upto M-50 grade i/c border or kurb block grey or coloured over sub-base of concrete with 25 mm thick average thickness of cement mortor 1:4 (1 cement : 4 sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks i/c curing rubbing and polishing complete (Sub base concrete floor to be paid for 60 mm thick inter locking blocks).

Providing and Fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including Fixing with approved adhesive etc. complete. 75 mm dia.

110 mm dia.

Providing and Fixing PVC plain bend ISI marked including Fixing with approved etc. complete. 75 mm dia.

110 mm dia.

Providing and Fixing PVC door bend with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including Fixing with approved etc. complete. 75 mm dia.

110 mm dia.

Providing and Fixing PVC collars ISI marked including Fixing with approved etc. complete.75 mm dia.

110 mm dia.

Providing and Fixing PVC singal equal branch plain ISI marked including Fixing with approved etc. complete. 75mm dia

110 mm dia.

Providing and Fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm thick bolts and nuts complete including Fixing with approved etc. complete. 75mm dia

110 mm dia.

Providing and Fixing PVC floor trap ISI marked of self cleaning design including Fixing with approved, cost of cutting and making good the wall and floors etc. complete. 110mm x 90mm

Providing and Fixing vitreous China wash, down water closet (EuropeanType WC pan) with integral "P" or "S" trap including jointing the trap with soil pipe in cement mortar 1:3 (1 cement : 3 sand) ( seat and cover to be measured and paid for seperately) : Anglo Indian (Universal Closet) in all leads and lifts. One piece WC for toilet including cistern & seat cover cera make CRUSE.

Two piece WC for other toilet CERA make CRUSE.

Providing and Fixing white solid type plastic sheet and cover for wash down water closet with CP brass hinges and rubber buffers. Two piece WC for other toilet CERA make CRUSE.

Providing and Fixing 10.00 liters Concealed cistern with a pair of C.I. or mild steel brackets, complete with fitting such as lead valve less syphon, 15 mm nominal size brass ball valve with polythene float, C.P. Brass handle, Unions and couplings for connections with inlet, outlet and couplings for connections with inlet, outlet and over flow pipes, 40 mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) in all leads and lifts. Two piece WC for other toilet CERA make CRUSE.

Providing & Fixing viterious china wash basin with single hole for pillar tap with C.I. or M.S. bracket painted white including cutting hole including good the same excluding fitting Cera sanitary work (cornet) white Flat back 630 mm x 450 mm.

Providing and Fixing viterious china pedestal for wash basin complete recessed at the basic for reception of pipe and fittings Cera sanitary work (carnet) white (Viterious China in White Colour)

Providing and Fixing M.I. Union for wash basin or sink 32 mm dia.

Providing and Fixing C.P. brass waste and plug for glazed ware sinks, basins etc. with long screwed shank and fly nut and fixed to steel pipe including vulcanite plug, brass chain and stud 32 mm nominal bore.

Providing and Fixing 600 mm x 450 mm bevelled edge mirror of superior glass marked on 6mm thick AC sheet or plywood sheet and fixed to wooden plug with CP brass screws and washer.

Providing and Fixing CP Brass towel rail complete with CP Brass brackets fixed to wooden plug with CP Brass screws 600 mm x 20 mm.

Providing and Fixing 600 mm x 120 mm glass shelf with C.P. Brass bracket and guard rail complete, fixed to wooden plugs with C.P. Brass screws.

Providing and Fixing Toilet paper holder C.P. brass.

Providing and Fixing chromium plated brass soap dish with C.P. Brass brackets fixed to wooden cleats with C.P. brass screws.

Providing and Fixing Tooth brush and Tumbler holder (Viterious China)

Providing and Fixing C.P. Brass Shower Rose with 15 mm to 20 mm inlet 100 mm dia.

Providing and Fixing brass bib tap (Superior or heavy type) 15 mm dia long nose.

Providing and Fixing brass bib tap (Superior or heavy type) 15 mm dia short body.

Providing and Fixing C.P. brass angle valve 15 mm without Nuts and pipe.

Providing and Fixing C.P. concealed stop cock 15 mm without Nuts and pipe.

Providing and Fixing one hole basin mixing Faucet.

Providing and Fixing P.V.C. connection with brass unions 300 / 450 mm length 15 mm nominal bore.

Providing and Fixing 100 mm dia chromium plated grating of superior quality for floor, gully or Nahni trap.

Providing and Fixing PTMT Jet spray of approved quality and colour with one meter tube.

Providing and Fixing of C.P. Towel ring of superior quality.

Providing and Fixing of C.P. towel rack 600 mm x 250 mm of superior quality.

Providing and Fixing stainless steel kitchen sink of approved standard ISI make with drain board and C.P. waste with C.I. or M. S. brackets painted white including cutting holes and making good the same but excluding fitting 610 x 460 mm with bowl depth 200 mm.

Providing and Fixing to wall ceiling and floor galvenised mild steel tubes (light grade) tube fittings and clamps including making good the wall, ceiling and floor in all leads and lifts. 25 mm nominal bore

Providing and Fixing brass full way valve with wheel of 25 mm dia (Heavy Duty) complete in all respect in all leads and lifts.

Providing and Fixing to wall ceiling and floor CPVC Pipe SDR 11 class - 1 (HSN Code : 3917) and clamps including making good the wall, ceiling and floor complete in all respect in all leads and lifts. 15 mm nominal bore

20 mm nominal bore

Providing and Fixing CPVC Coupler (HSN Code : 3917) of size mentioned below (Heavy Duty) complete in all respect in all leads and lifts.15 mm dia

20 mm dia

Providing and Fixing CPVC Elbow (HSN Code : 3917) of size mentioned below (Heavy Duty) complete in all respect in all leads and lifts.15mm dia

20 mm dia

Providing and Fixing CPVC Tee (HSN Code : 3917) of size mentioned below (Heavy Duty) complete in all respect in all leads and lifts. 15 mm dia

20 mm dia

Providing and Fixing CPVC Reducing Coupler (HSN Code : 3917) of size mentioned below (Heavy Duty) complete in all respect in all leads and lifts. 20x15 mm dia

Providing and Fixing CPVC Reducing Tee (HSN Code : 3917) of size mentioned below (Heavy Duty) complete in all respect in all leads and lifts. 20x15 mm dia

Providing and Fixing CPVC Tank Nipple (HSN Code : 3917) of size mentioned below (Heavy Duty) complete in all respect in all leads and lifts. 15 mm dia

20 mm dia

Providing and Fixing CPVC Union (HSN Code : 3917) of size mentioned below (Heavy Duty) complete in all respect in all leads and lifts. 15 mm dia

20 mm dia

Providing and Fixing CPVC Ball valve (HSN Code : 3917) of size mentioned below (Heavy Duty) complete in all respect in all leads and lifts. 15 mm dia

20 mm dia

Providing and Fixing PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. complete in all leads and lifts.

Providing and Fixing of PVC water storage tank sintex having of capacity 1000 liters with necessary fittings including over flow pipes, scour pipes etc. inlet and outlet and inside paint of required size for inlet or outlet and inside paint of approved quality complete including hoisting complete in all respects.

Construction of manhole with RCC top slab in 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:4:8 (1cement : 4 sand : 8 graded stone aggregate 40 mm nominal size) in side plastering 15 mm thick with cement mortar 1:3 (1cement:3 sand) finished with a floating coat of neat cement and making channel in cement concrete 1:2:4 (1cement:2 sand:4 graded stone aggregate 20 mm nominal size) including curing complete. i) In side size 800 mm x 800 mm x 500 mm deep excluding CI cover with frame (light duty single seal pattern - 1) 455 mm x 610 mm internal dimensions total weight of cover and frame to be not less than 38 kg. (Weight of cover 23 kg and weight of frame 15 kg) With 200 mm thick walls of brick masonry using common burunt clay building bricks in cement mortor 1:3 (1cement : 3 sand)

Providing and Fixing stoneware gully trap grade "A" complete with C.I. grating, brick masonry chamber in cement mortor 1:5 and water tight C.I. cover with frame of 300 mm x 300 mm size (inside) the weight of cover to be not less than 4.53 kg and frame to be not less than 2.72 kg. (Sqaure Mouth traps 100 mm x 100 mm size P type)

Constructing manhole with RCC top slab in 1:2:4 mix in (1cement :2 sand: 4graded stone aggregate 20mm nominal size ) foundation concrete 1:4:8 (1cement:4sand:8graded stone aggregate 40mm nominal size) inside plastering 15mm thick with cement mortor 1:3 (1cement:3sand) finished with a floating coat of neat cement and making channel in concrete 1:2:4 mix (1cement :2sand :4graded stone aggregate 20mm nominal size) finished smooth complete i/c curing and testing. Inside size 200x900x1000mm deep i/c C .I. cover with frame (Light duty single seal pattern-1) 455x610mm internal dimensions toal weight of cover and frame to be not less 38 kg. (Weigth of cover 23 Kg and weight of frame 15Kg.) with 200mm thick wall of brick masonery using common burnt clay building bricks in cement mortar 1:3 (1cement:3sand).

Constructing brick masonery chamber for under ground C I inspection chamber and bends with common burnt clay building bricks in cement mortar 1:5 (1cement:5sand) C I cover with frame (Light duty) 355x610mm internal dia total weight of cover and frame to be not less then 38Kg. (Weight of cover 23Kg and weight of frame 15Kg) RCC top slab with 1:2:4mix (1cement:2sand:4graded stone aggregate 20mm nominal size) foundation concrete 1:5:10 (1cement:5sand:10graded stone aggregate 40mm nominal size) inside plastering 15mm thick with cement mortor 1:3 (1cement:3sand) finished with a floating coat of neat cement on walls and bed concrete etc. complete. Inside dimensions 455x610x450mm deep single pipe line.

Providing & laying cement concrete work 1:2:4 (1 Cement: 2 Sand:4 graded stone aggregate 20mm nominal size) and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in:- Foundation,footings bases of column and the like mass concrete within all leads and lifts as per the direction of Engineer-in-charge.

Vertical walls (any thickness) partitions and the like including attached pillasters,buttresses, plinth and string courses etc. and the like within all leads and lifts.

Flat surface such as soffits of suspended floors,roofs,landing and like floors etc. upto 200mm in thickness as per direction and to the entire satisfaction of the Engineer-in-charge.

Manufacturing, febrication & fixing of M.S. man hole cover of 0.60x.60 m size made of M.S. Sheet 2.0 mm thick with M.S. angle 35x35x5mm thick with hinges one side and sliding door bolt for locking arrangement i/c cutting, welding and priming & Painting two coats of anamel paint sky complete in all respect to the entire satisfaction of the Engineer-in-charge.

P/Fixing pressed steel doors frames manufactured from commercial mild steel sheet of 1.25mm thickness including hinges jump lock jamb, beed and if reuired angle threshold of mild steel angle of section 50x25mm or base ties of 1.25mm pressed mild steel weided or refidly fixed together by mechanical means abjustable lugs with split and tails to each jamb including steel but things 2.5mm thick with guards lock strike plant and shocl as specified and applying a coat of approved steel primer after pretreetment of the surface as directed by Engineer-in charge.

Providing and fixing wood paneled glazed or paneled and glazed shutters for doors, windows and clear story 40mm thick windows including bright finished black enameled iron with necessary screws with second class deodar wood 40mm thick in all leads and lifts.

Prov. & fixing wire gauge shutters using galvanized MS wire gauge of IS gauge designation 85 G. with wire of dia. 0.56 mm for doors,windows & clerestrey windows including bright finished black enameled iron hinges with necessary screws.

Providing Laying and jointing of G.I. pipe 15mm dia to provide connections to cistern, Tap.

Prov. & fixing sand cast/cast iron spun spigot and socket soil waste and ventilating pipes (lead caulked joints to be measured and paid for separately) 50mm dia nominal size.

Prov. & fixing Vitreous china wash down water closet squatting pan (European type WC pan) with P or S trap i/c jointing the trap with soil pipe in cm 1:1 (1 Cement:1 sand) includind seat cover (Anglo indian type universal closer (earth work bed concrete footrest and trap to be measured and paid for separately) complete within all leads and lift.

Prov. & fixing 10.0/12.5/15.00 ltrs viterous china low level flushing cistern with a pair of CI or mild steel brackets complete with fitting such as lead valve less syphon 15mm nominal size brass ball valve with polythene float,CP brass handle unions and couppling for connections with inlet,outlet and over flow pipes.

Sushant Puri

Sarbjit Singh Katoch

Suraj Parkash Aggarwal

vikas parmar