LAC-ADS-CPP-MLBC-Renovation and motorization of 2 Nos of Kambalathala Eri shutters-General Mechanical Work

Amount

CPP-MLBC-Renovation and providing motorized screw hoist for 2Nos of MLBC main shutters of Kambalathara Eri

OD31180/2024-2025:RING BUND - PUTTING UP RING BUND as per approved shape 7m bottom width and 4 m top width using empty gunny bar polythene bag filled with earth placed in two rows at 1m apart and filled in between with puddle clay to form bund for an average height 5m and total length of 25m including labour, materials. REMOVING the bund after COMPLETION of WORK.(#)

OD30852/2024-2025:[60.2.4] BAILING OUT WATER USING PUMP ABOVE 10HP and UP TO 20HP - Bailing out water with engine and pump set above 10HP and up to 20HP, including conveyance to site and erection, cost of fuel, lubrication oil and other stores, pay of staff etc complete.(#)

15.3:Demolishing R.C.C. work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material with in 50 metres lead as per direction of Engineer -in-Charge.

15.9.2:Demolishing stone rubble masonry manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer -in- Charges:In cement mortar

4.3.3:Centering and shuttering including strutting, propping etc. and removal of form work for:Columns, piers, abutments, pillars, posts and struts

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

OD30741/2024-2025:Drilling hole on civil structure dia up to 24 mm and depth up to 250mm without damage existing any structure and cleaning the hole for preparation of Chemical Anchor. Including cost of all materials, labour charges, energy charges, hire charges etc.complete. As per the instructions from the deptl officals.(#)

OD30742/2024-2025:Anchoring the MS/SS rebars into the drilled hole using CHEMICAL ADHESIVES, including cost of hire charge of machine, cost of chemical adhesive and labour.(#)

5.2.2:Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

OD30855/2024-2025:Dismantling of the Canal Shutter ( up to 2 Tonne weight ) /Hoisting unit / Embedded parts etc. of the same and stacking of a distance of 100 meter including hire of machinery, labour etc complete as directed by the deptl. officer at the site (Weight of the unserviceable shutters and embedded parts may be calculated as 60% and unserviceable hoisting units as 80%)-(CANAL GATE 4-16)

OD29209/2023-2024:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

OD29210/2023-2024:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

OD29211/2023-2024:Supply of MS round bar including cost of conveyance charges

85.103:Supply of MS checquered plates including cost of conveyance charges

OD29212/2023-2024:Supply of SS BOLT and NUT up to 300mm Length including cost of conveyance.

OD29213/2023-2024:Fabrication,Supply,Erection and Assembling in correct position and alignment by welding SS Embedded parts in 304L Grade like roller track,seal track,Seal seat etc as per approved specifications,drawings and directions of deptl officer at site including cost of all materials,labour,machinery for planing,welding,shearing,grinding etc,lead and lift,conveyance,incidental and handling etc complete

OD29214/2023-2024:Fabrication and errection of Embedded parts for canal shutters ( lJp to 2 tonne weight ) and accessories as per approved specifications, drawings and directions of deptl fficer at site including cost of labour,machinery, all leads and lifts, incidental and handling charges etc complete but excluding cost of material already supplied.

OD29215/2023-2024:Fabrication and supply of Structural steel canal shutters ( Up to 2 tonne weight ) /Hoisting Bridge /Platform and accessories etc. for the same as per approved specifications, drawings and directions of deptl fficer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc complete but excluding cost of material already supplied

OD30844/2024-2025:Providing of double worm and pinion having a lifting speed of around 5.00 cm/min for hand operation/manual operation including cost of all materials, labour, hire charges and conveyance- (CANAL GATE 16-16)

OD32218/2024-2025:Supply and fixing of 3 HP MOTOR and REDUCTION GEAR UNIT driven through self locking worm reducer, coupling mechanism for engaging/disengaging including cost of all materials, labour, hire charges and conveyance.

OD31896/2024-2025:Supplying and fixing of individual STARTER BOARD including cost of all labour, materials, incidental charges etc.

OD31897/2024-2025:Supplying and fixing of MAIN PANEL BOARD including electrical accessories etc. complete including cost of materials, labour, incidental charges etc.

85.114:Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

85.115:Cost of painting with 2 coats of enamel paint over 1 coat of zinchromate primer as per IS1477:1994 after hand and power tool cleaning including cost of all materials, labour charges, cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

OD29218/2023-2024:SUPPLYING and APPLYING GREASE on NEW SCREW ROD for CANAL GATE

85.116:Supplying and fixing in correct position with specified initial interface the flat type rubber seal confirming to IS 11855 to the gates including cost of SS bolts and nut all labour and machinery and incidental and conveyance charges complete as per approved specification and drawing

85.118:Supplying and fixing in correct position with specified initial interface L-type / bulb nose rubber seal confirming to IS11855 to the gates including cost of SS bolts and nuts and all labour and machinery and incidental and conveyance charges complete as per approved specifications and drawings

OD30819/2024-2025:SUPPLYING, STACKING and FIXING of ANGULAR BULB NOSE RUBBER SEAL for corner (400mm X 400mm).(#)

OD29219/2023-2024:Supplying and fixing cast steel thrust roller assembly having 250mm Dia, 50mm tread width, SS(304) shaft and 22313E self aligning spherical roller bearing and accessories as per approved specifications and drawings including cost of all materials, machineries, labour , all lift and lead, incidental and conveyance charges etc complete

OD29221/2023-2024:Providing screw rod locking arrangement to the shutters including cost of materials ,fixing charges etc complete

OD29222/2023-2024:SUPPLYING and STACKING of PAD LOCK.

OD30854/2024-2025:SUPPLY of BUTT HINGE(#)

OD29220/2023-2024:Erection of the Canal Shutter ( Up to 2 Tonne weight ) / Hoisting Bridge / Platform including hand rails , lader etc. for the same including . alignment correcting and setting complete including cost of all labour, machinery, incidental and conveyance , lead and lift charges etc complete but excluding cost of materials already supplied..

OD31903/2024-2025:ASSEMBLING the Motor and gear box mechanism to the bridge and conducting TRIAL RUN

OD31188/2024-2025:Preparing design and drawing of shutter and motorised hoisting mechanisms suited for existing screw rod and worm and pinion mechanism as per standard specifications and submitting hard and soft copies of all GA, fabrication and detail drawings.

OD35853/2024-2025:Supplying, stacking and erection of Dial assembly for shutters including cost of all material, labour,hire charges etc. complete.

OD35854/2024-2025:SUPPLYING and FIXING of individual starter board including cost of all labour, materials, incidental charges etc

V M Asharaf (BID ID -2182778)

Bidder Name

Kinanath V P

V M Asharaf