construction of Cow Shed at Nageshwar Mahadev Kud, Gram Panchayat Bharol, Dev Block Chountra on Khasra no 2466 at Mohal Gavela Tehsil Lad Bharol District Mandi HP SH Construction of Community Toilet, Two nos Urine Collection Tanks Rain water harvesti

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means in foundation ,trenches ,drains (Any width or square metre on plan),inlcuding dressing of sides and ramming of bottoms,lift upto any height,including getting out the excvated soil and disposal of surplus excvated soil as directed in all kinds of classifications of solis such as pick work,jumper work,blasting work saturated soils including chiseling or any other mixed variety of soils,dewatering and/or removal of slush and other incidentasls within all leads and lifts complete in all respect as per directions and satisfaction of Engineer -in-Charge.Any loss to the public or private property during the course of excvation shall be the sole responsibility of the contractor which shall have to be duly compensated by him at his own cost in all cases including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer -in -Charge.

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km (five kilometere) also including ramming and watering of the earth in layers not exceeding 20 cm (twenty centimeter) in trenches, plinth, sides of foundation etc. complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer -in -Charge.

Supplying, filling, spreading & leveling stone boulders /stone soling hand packed of size range 50mm to 200mm,(Fifty mm to Two hundred mm) under floor/path as soling etc, in the required thickness, for all leads & lifts, all complete including carriage of materials with in all leads, lifts and other incidentals as per direction of Engineer-in-charge.

Providing and laying cement concrete 1 : 4 : 8 (one cement : four sand : eight graded stone aggregate 40 mm (Forty millimetre nominal size) mechanically mixed and vibrated and curing complete excluding cost of form work in foundation and plinth including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in-charge.

Providing and laying cement concrete work 1:2:4 (one cement : two sand : four graded crushed stone aggregate 40mm (Forty millimetre nominal size) and curing complete excluding cost of form work in foundation and plinth including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in-charge.

Providing and laying M- 25 (twenty five) grade reinfoced cement concrete work mechanically mixed and vibrated with minimum cement contents of 400 Kg. (four hundred Kilogram) per cubic metre with graded crushed stone aggregate 20mm (twenty millimetre) nominal size and curing complete excluding cost of form work and reinforcement for reinforced cement concrete work in:- Foundation, footings bases of columns etc. and mass concrete including carriage of materials with in all leads, lifts and other incidentals .

Providing and laying M- 25(twenty five) grade reinforced cement concrete work mechanically mixed and vibrated with minimum cement contents of400 Kg. (four hundred Kilogram) per cubic metre with graded crushed stone aggregate 20mm (twenty millimetre) nominal size and curing complete excluding cost of form work and reinforcement for reinforced cement concrete work in:- Columns, pillars, posts and struts square rectangular polygonal in plain upto floor all level including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying M- 25 (twenty five) grade reinforced cement concrete work mechanically mixed and vibrated with minimum cement contents of 400 Kg. (four hundred Kilogram) per cubic metre with graded crushed stone aggregate 20mm (twenty millimetre) nominal size and curing complete excluding cost of form work and reinforcement for reinforced cement concrete work in:- Suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels upto floor all level including carriage of materials with in all leads, lifts and other incidentals.

Providing Tor steel reinforcement TMT bar Fe 500 ISI make high yield strength for reinforced cement concrete work including bending, binding and placing in position cost of binding wire complete upto floor all level including carriage of materials with in all leads, lifts and other incidentals complete in all respect as per as direction and to the entire satisfaction of Engineer -in -Charge.

Providing form work with steel plates 3.15mm (three point fifteen millimetre) thick welded with angle iron in frame 30x30x5mm (thirty millimetre into thirty millimetre into five millimetre) so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and ballies in any height of propping and centering below supporting floor to ceiling upto floor all level and removal of the same for in-situ reinforced concrete and plain concrete work including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in-charge in:- :Foundations, footings, bases of columns, etc. for mass concrete

Providing form work with steel plates 3.15mm (three point fifteen millimetre) thick welded with angle iron in frame 30x30x5mm (thirty millimetre into thirty millimetre into five millimetre) so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and ballies in any height of propping and centering below supporting floor to ceiling upto floor all level and removal of the same for in-situ reinforced concrete and plain concrete work including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in-charge in:- Lintels, beams, plinth beams, girders, bressumers and cantilevers

Providing form work with steel plates 3.15mm (three point fifteen millimetre) thick welded with angle iron in frame 30x30x5mm (Thirty millimetre X Thirty millimetre X Five millimetre) so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and ballies in any height of propping and centering below supporting floor to ceiling upto floor all level and removal of the same for in-situ reinforced concrete and plain concrete work including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in-charge in ;-Suspended floors, roofs, landings, balconies and access platform

Providing form work with steel plates 3.15mm (three point fifteen millimetre) thick welded with angle iron in frame 30x30x5mm (thirty millimetre into thirty millimetre into five millimetre) so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and ballies in any height of propping and centering below supporting floor to ceiling upto floor all level and removal of the same for in-situ reinforced concrete and plain concrete work including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in-charge in:- Columns, Pillars, Piers, Abutments, Posts and Struts

Half Brick work using second class common burnt clay building bricks in super structure above plinth level upto all floor level in cement mortar 1:4 (one cement : four sand and curing complete ) including carriage of materials with in all leads, lifts and other incidentals.

Brick work using second class common burnt clay building bricks in super structure above plinth level upto all floor level in cement mortar 1:6 (one cement : six sand) and curing complete including carriage of materials with in all leads, lifts and other incidentals.

Random rubble masonry (un-coursed/ brought to courses) with hard stone of approved quality in foundation and plinth including leveling up with cement concrete 1 : 6 : 12 ( one cement : six sand : twelve graded crushed stone aggregate 20mm (Twenty millimetre) nominal size) at plinth level including racking out joints in cement mortar 1: 6 (one cement : six sand) and curing complete including carriage of materials with in all leads, lifts and other incidentals.

15mm (Fifteen millimeter) cement plaster in single coat on the rough side of brick/concrete /stone walls for interior & Exterior walls plastering up to all floor level including arises, internal rounded angles, chamfers and /or rounded angles not exceeding 80mm (Eighty millimeter) in girth and finished even and smooth in cement mortar 1:6 (one cement : six sand) upto all floor level including carriage of materials with in all leads, lifts and other incidentals.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture nerolac/Asian paint and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth upto all floor level including carriage of materials with in all leads, lifts and other incidentals.

Providing and placing in position 100 mm (Hundred milimetere) thick factory made machine batched & machine mixed Precast RCC Rectangular Covers on drains of footpath of various sizes, of M-25 grade cement concrete for RCC work, including cost of centering, shuttering, reinforcement of 8 mm (Eight milimeter) dia TMT bars of Fe 500 (Five Hundred) grade @ maximum 100mm (Hundred milimetre) c/c on both ways , neat cement punning on finished surface, properly encased on all edges with 1.6 mm (One point six milimtere) thick , 100 mm (Hundred milimetere) wide MS sheet duly painted over priming coat , reinforcement to be welded at edges with MS sheet and providing 2 Nos (Two No.'s. 12 mm (Twelve dia bar for hooks etc including cost of cartage, all leads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge.

Providing and fixing M.S. grill of required pattern in wooden/steel frames of windows etc. with M.S. flat square or round bars with round headed bolts and nuts or by screws plain grill including carriage of materials with in all leads, lifts and other incidentals.

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture including carriage of materials with in all leads, lifts and other incidentals

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion - Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15 (Fifteen) )including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) :Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15 Fifteen) ) including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): etc.: -With float glass panes of 4.0 mm thickness weight not less than 10.00 kg(Ten kilograms) / sqm including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. - Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side including carriage of materials with in all leads, lifts and other incidentals.

Kota stone slab flooring over 20 mm Twenty milimeter (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :25mm thick including carriage of materials with in all leads, lifts and other incidentals.

Steel work welded in built up sections, trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of red lead paint in beams, joists, channels, angles, tees, flats with connection plates or angle cleats as in main and cross beams, hip and jack rafters purlins connected to common rafters and the like including carriage of materials with in all leads, lifts and other incidentals.

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.63 mm ( point Six three millimetre ) thick with zinc coating not less than 275 gm/ m² including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 0.60mm (Zero point sixty millimetre) thick preprinted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyester (RNP) organic coating of 20 (Twenty) microns over 5 (five) microns primer coating to back coat of polyester of 5 (five) microns over 5 (five) microns primer coating including fixing with screws preprinted iron J or L hooks, bolts and nuts 6mm (Six millimetre) dia metre with preprinted limpet and rubber washers complete with all accessories as required as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing ridges or hips 60 cm (sixty centimetre) overall with 0.60mm (Zero point sixty millimetre) thick pre-painted steel sheets in roofing with hot dipped metallic zinc coated sheets with top coat of regular modified polyester organic coating of 20 (Twenty) microns over 5 (five) microns primer coating + back coat of polyester of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer in Charges including carriage of materials with in all leads, lifts and other incidentals.

Supplying & fixing at site Angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm(Ten centimeter) length and drilling holes upto 10 mm dia(Ten mm dia.). etc. including carriage of materials with in all leads, lifts and other incidentals.

Fencing with angle iron post placed at required distance embedded in cement concrete blocks, every 15th(Fifthenth ) post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with horizontal wires, of barbed wire weighing 9.38 kg (Nine point thirty eight Kg/ Per 100 m (Hundred meter minimum), between the two posts fitted and fixed with G.I. staples, turn buckles etc. complete. (Cost of posts, struts, earth work and concrete work to be paid for separately).including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm (Fifty x Fifty mm ) including strengthening with 2 mm (Two mm dia) dia wire or nuts, bolts and washers as required complete including carriage of materials with in all leads, lifts and other incidentals as per the direction of Engineer-in-charge.

Disposal of moorum/building rubbish/ malba/ simila transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km(Ten Kilometers) for all lifts, complete as per directions of Engineer-in-charge. Note - item to be applicable in urban areas having directions for restricted hours for movement/ plying of load carrying motor vehicle of 3.5 cum (Three & Half Cum) or more including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing CPVC Pipes 15 mm dia.(Fifteen milimeter) Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work -Exposed on wall including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing CPVC Pipes 15 mm dia.(Fifteen milimeter) Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work -Exposed on wall including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 20 mm dia.(Twenty milimeter) G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. 20 (Twenty milimetere) mm dia nominal bore (Medium) including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 100mm (One hundred millimetre) sand cast iron grating for gully floor or Nahni trap including carriage of materials with in all leads, lifts and other incidentals..

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm (Hundred milimetere) sand cast Iron P or S trap, 10 litre (Ten Litre) low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre (Ten litre) low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm (Forty milimetere) flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 8 mm dia(Eight milmiter) C.P. / S.S. Jet with flexible tube upto 1 metre (One meter) long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing wash basin with C.I. brackets, 15 mm (Fifteen milimetere) C.P. brass pillar taps, 32 mm (Thirty Two milimetere) C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour.Waste coupling 31 mm (Thirty One to Seventy Nine milimeter) dia of 79 mm(Seventy Nine milimeter) length and 62mm (Sixty Two milimeter) breadth weighing not less than 45 gms(Forty Five grams) including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm (Four hundred Thirty x Two hundred sixty x Three hundred fifty) and 340x410x265 mm (Three hundred forty x Four hundred Ten x Two hundred Sixty five )sizes respectively with automatic flushing cistern with standard flush pipe and C.P. Brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing Division plate for urinal 600x300mm (Six hundred x Three hundred millimeter) vitreous china complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals. including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing C.P. brass angle valve /angle cock for basin mixer /others locations of approved quality conforming to IS:8931 - 15mm (Fifteen milimeter) nominal bore including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing PTMT soap Dish Holder having length of 138mm (One hundred thirty eight ) breadth 102mm, height of 75mm (Seventy Five milimeter)with concealed fitting arrangements, weighing not less than 106 gms (One hundred & six grams) . including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 453x357mm (Four Hundred fifty Three x Three Hundred Fifty Seven milimeter) mirror of superior glass mounted on 6mm (six millimetre) thick A.C. sheet or plywood sheet and fixed to wooden plugs with C.P. brass screws and washer including carriage of materials with in all leads , lifts and other incidentals. including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball.including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms (Eight Hundred and Ten grams) ).including carriage of materials with in all leads, lifts and other incidentals.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 75 mm dia (Seventy Five milimetere) on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (Ten milimeter) gap for thermal expansion, (i) Single socketed pipes. including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing110 mm dia (One hundred and Ten milimeter) on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (Ten milimeter) gap for thermal expansion, (i) Single socketed pipes. including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 110mm dia Coupler (One Hundred & Ten milimeter) on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion all complete.including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 75 mm dia Bend (Seventy Five milimeter)on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing Bend 87.5 degree,110mm bend (One hundred & Ten milimeter) on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion all complete.including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing Shoe,110mm bend (On Hundred & Ten milimeter)on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion all complete.including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing unplasticised - PVC pipe clips of approved design to unplasticised PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete including carriage of materail with in all leads and lifts and other incidentals.

BUDHI SINGH

LEKH RAJ