PROVISION OF STORAGE ACCN AND EXTENSION OF COVERED SHED AT KOCHI

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out any type of soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and directed

Material and labour for plain Cement concrete in foundations, filling and mass concrete type D2(1:4:8) using 40 mm graded stone aggregate complete all as specified and directed

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed

S&F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed

S&F PVC (SWR) pipes 110mm bore double socketed in any length with rubber ring joints fixed to walls for rain water pipes complete all as specified and directed

M&L for two coat of synthetic enamel paint over 10 cm width or girth,not otherwise described over a coat of redoxide on new steel surfaces incl preparation complete all as specified and directed

Excavation in trenches, not exceeding 1.50 meter wide and not exceeding 1.5 meter in depth, for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not of any type of soil complete all as specified and directed

M&L for RCC M-30 design mix concrete in foundation, including rafts, footings, foundation beams, plinth beams, bases for columns etc; basement slabs, under reamed piles and mass concrete complete all as specified and directed Note: Reinforcement and form work measured and paid separately.

M&L for form work to sides of concrete foundations, foottings, bases of columns, raft and raft beams, sides and soffits of foundation and plinth beams and similar works; vertical or to batter for rough finished surfaces complete all as specified and directed

M&L for sand cushioning under interlocking tiles including watering and consolidtion complete all as specified and directed.

M&L for mild steel bars 10mm dia and over FE 410 W(Gde E250) quality A cut to length and bend to shape as required,,including cranking,bending,prirally for hooping and inserting in to footing as bolting in concrete include necessary washer and bolts complete all as specified and directed

M&L for reinforced cement concrete (Design Mix, M-30) in beams, cantilevers, bressummers, lintels over 1.50 meter span complete all as specified and directed Note : Reinforcement and form work measured and paid separately.

M&L for reinforced cement concrete (Design Mix, M-30) in Chhajha complete all as specified and directed Note : Reinforcement and form work measured and paid separately.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels cantilevers, shelves including supports, overhung etc. also splays between floors and beams etc. as in rough finished surfaces complete all as specified and directed

M&L for formwork to chullah hoods, cha-jjas, troughs and similar items in-cluding edges complete all as specified and directed

M&L Pre-cast cement concrete block Type C1 1:3:6 (20 mm graded aggregate) masonry with solid blocks, exc. 10 cm in width and setting in mortar 1:6 , complete all as specified and directed

S & F 125 x 60mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified

S & F 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed

S & F anodised powder coated aluminium frame for windows,ventelator with one or ,more rebate including joining cleats for fixing etccomplete all as specified

Supply and fixing anodised aluminum powder coated ventelator shutters fixed type without sash bars,aluminium ectionweighing 0.55kg/m including necessary joining cleats,glazing clips,rubber packing,anodised aluminium snap beading,crews etc omplete all as specified

Supply and fixing anodised powder coated aluminium window shutters ,side hung typewithout sash bars,aluminium ectionweighing 0.55kg/m including necessary joining cleats,glazing clip,rubber paking,anodised aluminium snap beading, crews, anodised aluminium fittings such as peg stays150mm long 01 no,hinges type B-21 100mm long (2nos) suitable handle(01 no) complete all as specified

Supply and fixing 4mm thick figured glass,pin headed type and glazing with rubber beading or with glazing clips n exc 0.5 sqm all as specified and directed

Supply and fixing stainless steel wire loth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed

S&F 100mm long Butt hinges, heavy weight, cold rolled mild steel, and fixed complete all as specified and directed

S&F 200 mm long 10 mm dia Aluminium tower bolt complete all as specified and directed

S&F 150 mm long Mild steel pressed handles, oval type, stove enamelled black complete all as specified and directed

S&F 150mm Long, 16mm Dia Aluminium Aldropbolt complete all as specified and directed

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed

M&L for rendering 10 mm thick in CM 1:6 on PCC block masonry brick work or concrete surfaces to be finished even and smooth without using extra cement in internal walls complete all as specified and directed

M&L for rendering 15 mm thic in CM 1:4 on PCC block masonry brick work or concrete surfaces to be finished even and smooth complete all as specified and directed

M&L for preparing new plastered surfaces of wall & apply three coat of white wash over a coat of lime putty cpmplete all as specified and directed.

M&L for preparing new plastered surfaces of wall & applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed

M&L TMT bars 10 mm dia and over cut to length bent to shape required including cranking,bending,spirally for hooping and binding with and including mild steel wire anealed not less than 0.9 mm dia complete all as specified and directed

All as per item No. 36 here in before but 5 mm dia and over up to and including 10 mm dia in stirrups spacers and binders complete all as specified and directed

M&L for two coat of synthetic enamel paint over 10 cm width or girth,not otherwise described over a coat of pink primer on new wooden surface including preparation complete all as specified and directed

M&L for hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 75 mm thick, watered and rammed to a true surface complete all as specified and directed

M&L for PCC for 50 mm thick (1:3:6) type D-2 using 20 mm graded stone aggegate plinth protection complete all as specified and di

M&L for PCC (1:4:8) type D-2, (using 40 mm graded stone aggregate),75 mm thick, as in sub base for floor, finished even and rough complete all as specified and directed.

rected

M&L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 15 mm thick cement screed in (1:4 ) CM complete all as specified and directed.

M&L for Machine cut kota stone slab in skirting 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 10 mm thick cement screed in (1:4 ) CM complete all as specified and directed.

M&L for non skid ceramic Coloured tiles, 300mmx300mmx6mm to7mm thick, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match with the colour of tiles, over and including 15 mm thick screed bed or bedding layer of cement mortar 1:4 complete all as specified and directed.

M&L Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre.

M&L Providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wire mesh (Fillets, metal frame work and G.I. wire mesh paid separately)

S&F Vitreous China, wash down water closet pan "Pedestal pattern" white including connection to drain and to flush pipe and anti syphonic pipe including all joints and making good the disturbed surfaces complete all as specified.

S&F in Repairs PVC valve-less, syphonic action type, flushing cistern, low level, 10 litre capacity (ISI marked) white with inlet, ball valve, float and handle, flush pipe of polyethylene pvc 32mm dia high or low density including brackets complete all as specified and directed.

S&F PVC connections 15 mm dia and 450 mm long with brass nuts complete all as specified

S&F chromium plated shower rose 125 mm size and Shower arm 15 mm size, 195mm long with bend of 45degree with flange of PTMT any colour.(Minimum weight 40gms

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F Tubular towel rail, Brass chromium plated 20mm dia, D type, 60cm long between flanges complete all as specified and directed

S&F Liquid soap container of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 105gms) complete all as specified and directed

M&L PVC (SWR) 50 mm multi floor trap with grating including jointing with solvent cement complete all as specified and directed

M&L PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed

S&F (concealed / open) 15mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified

S&F (concealed / open) 20mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified

S&F (concealed / open) 25mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified

S&F fancy type bip tap cast copper alloy chromium plated with crutch or butterfly handle screwed down,screwed for pipe and fixed

S&F fancy typePillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed

S&F Stop valves, fancy type cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed

S&F Stop valves, concealed fancy type cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed

S&F Grating square 150 mm size of PTMT (Minimum weight 100gms) complete all as specified and directed

S&F Vitreous Cliina wash basin, wliile, flat back, size directed irun including waste, chain and plug and porcelain stopper but including brackets complete all as specified and directed

S&F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring jointsfixed on walls complete all as specified and directed

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring jointsfixed on walls complete all as specified and directed

S&F PVC (SWR) bends, 110 mm bore, any radius with access door complete all as specified and directed.

S&F PVC (SWR) bends, 75 mm bore, any radius with access door complete all as specified and directed.

M&L Returning filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm in soft/ loose soil complete all as specified and directed

M&L removal of excavated soil n exc 50m and depositing where directed at a level n exc 1.5 m above the starting point complete all as specified and directed