SPECIAL REPAIR TO BUILDING NO P- 45 IN TIRAH LINE AT MIL STN DHARAMSHALA

Amount

Taking down chowkhats or frames with shutters (without taking off shutter from the frame) area not exceeding 1.50 sqm each and removing complete, all as specified and as directed by the Engineer-in-Charge.

Taking down shutters exc. 1.5 sqm but not exc. 2.0 sqm each all as specified and directed by Engr-in-Charge.

Taking down shutters exc. 2.0 sqm but not exc. 4.0 sqm each all as specified and directed by Engr-in-Charge.

Factory made PVC solid door frame of size 50mmx47mm made out of 5mm wood grain printed PVC sheet reinforced with MS square tube, complete all as spcified and directed by Engr-in-Charge.

PVC door Factory made solid panel shutter, 30mm thick (Stile) consisting of frame made out of M. S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent for top rail, lock rail & battom rail on either side & as gap insert for top rail & bottom rail: Panelling of wood grain printed PVC sheet to be fitted in the M. S. frame welded/sealed to the stiles & rails with suitable 5mm thick x 15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (90 degree) used instead of exposed portion of PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing on page No.156 of MES SSR Part-II 2010, complete all as spcified and directed by Engr-in-Charge.

Pressed steel frame of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified and directed by Engr-in- Charge.

Factory made, 2nd Class, hard wood (Sal/Hollock) plain, framed, panelled 35mm thick shutters (two panels) with lock rail and panels of 9mm BWP commercial plywood or 12mm veneered particle with commercial face veneers on both sides. The size of rail and style as per IS-1003 (Part-I), kiln seasoned and chemically presure treated complete all as specified and directed by Engr-in- Charge.

30mm thick 2nd class soft wood glazed and skelton shutters open rebated and prepared to receive glass, gauge etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in SSR Part-I, Section 8 clause 8.24 (a) supplied and fitted to chowkhats complete, all as specified and as directed by the Engineer-in-Charge.

All as per items No. 08 here-in-above but divided into square with sash bars.

2nd Class soft wood, plain, solid chowkats and frame wrought, framed, rebated on the solid, rounded or chamfered put together with glue pinned at joints complete, all as specified and as directed by the Engineer-in-Charge.

Mild steel galvanised wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks or wire staples or wooden beads complete (fixed in repair), all as specified and directed by Engr-in- Charge.

150mm aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed by Engr-in- Charge.

100mm aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed by Engr-in- Charge.

100mm butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed by Engr-in- Charge.

75mm butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed by Engr-in- Charge.

100mm long aluminium alloy handles, cast type, anodised complete all as specified and directed by Engr-in- Charge.

150mm long aluminium alloy handles, cast type, anodised complete all as specified and directed by Engr-in- Charge.

300mm long, mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed by Engr-in-Charge.

100mm size hasp and staple safety type brass with mild steel hinges pin including bolt to hinge plate and fixed with screws, complete all as specified and directed by Engr-in-Charge.

12mm thick plywood, BWR, type BB fixed with screws to timber frame work asin cup board shutters complete, all as specified and directed by Engr-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or steel, concrete or brick surrounded, glazed with oil putty or fixed with beads complete, all as specified and directed by Engr-in-Charge.

3mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in square n.exc.0.50 sqm in each pane complete, all as specified and directed by Engr-in-Charge.

Two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces including prepration of new steel surface complete all as specified and directed by Engr-in-Charge.

Two coats of synthetic enamel paint over a coat of red oxide primer on old steel surfaces including prepration of new steel surface complete all as specified and directed by Engr-in-Charge.

Two coats of synthetic enamel paint over a coat of pink primer on new wood or wooden based surfaces of any description, n. exc. 10cm width or girth including preparation of surfaces complete, all as specified and directed by Engr-in-Charge.

Two coats of synthetic enamel paint over a coat of pink primer on old wood or wooden based surfaces of any description, n. exc. 10cm width or girth including preparation of surfaces complete, all as specified and directed by Engr-in-Charge.

Taking down Cement plaster on brick or stone or concrete surfaces etc including racking out joints, hacking for key, scrubbing down with water complete all as specified and directed by Engr-in-Charge.

Rendering 10 mm thick on fair faces of brick or concrete surface in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed by Engr-In-Charge.

Preparation of new plastered wall surfaces and applying two coats of oil bound distemper complete all as specified & directed by Engr-in-Charge.

Preparation of old plastered wall surfaces and applying two coats of oil bound distemper complete all as specified & directed by Engr-in-Charge.

Rendering 15mm thick on fair faces of brick or concrete surface in CM 1:4, finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

Supply only liquid water proofing compound complete all as specified and directed by Engr-in-Charge.

Two coats of all weather exterior paint over a coat of primer on newly plastered wall surface including prepration of plastered/ unplastered surface, complete all as specified and directed by Engr-in-charge.

Rendering 5mm thick on concrete surface as in ceiling in CM 1:4, finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

Two coats of oil bound distemper on newly plastered surface of ceiling over a coat of chalk whiting including preparation, complete all as specified and directed by the Engr-in-Charge.

Demolition of cement concrete in ground floors & paving not exceeding 15 cms thick (below or above ground level), complete all as specified and directed by Engr-in-Charge.

Plain Cement concrete, 25mm thick, type B-1, M-15 (using 20mm graded crushed stone aggregate) finished rough to receive floor finishes, complete all as specified and directed by Engr-in-Charge.

75mm thick cement concrete, M-10, type C-2 (using 40mm graded crushed stone aggregates) as in plinth protection complete, all as specified and as directed by the Engineer-in-Charge.

Mat Finish (non-skid) premium class-I grade, coloured Ceramic tiles 7 to 8 mm thick, area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over 15mm thick screed bed in cm 1:6 complete all as specified and directed by Engr-in-Charge.

Mat finish (non skid) coloured tiles 7 to 8mm thick, straight edge, standard economic class-II, A- grade, area of each tiles exc.0.18 sqm but n.exc 0.38 sqm in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engr-in-Charge.

Machine cut, mirror polished 20-25 mm thick kota stone as in flooring, over 15mm thick screed bed in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing grinding and polishing complete, all as specified and directed by Engr-in-Charge.

Machine cut, mirror polished 20-25 mm thick kota stone as in skirting, over 10mm thick rendering in CM 1:3 and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing grinding and polishing complete, all as specified and directed by Engr-in-Charge.

Demolition of Trezzo/Tiles/cement plaster of any thickness as in vertical surface complete all as specified and directed by Engr-in-Charge.

Glazed ceramic coloured tiles of size 450X350X7mm thick as in vertical concrete /brick surfaces, set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed by Engr-in- Charge.

20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillar, window-cills, cooking platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigments to match with shade of granite complete all as specified and directed by Engr-in-Charge.

Sink made of stainless steel 1mm thick (in replacement) kitchen or laboratory with plugs, washers and wastes,including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe,overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm including 40mm size CP waste coupling & PVC waste pipe, including demolition of existing terrozo/cement slab sink fixed (in repair), complete all as specified and directed by Engr-in-Charge.

PVC valve less, crystal white , syphonic action type flushing cistern 10 liters capacity, superior quality , plunger type, low level, with inlet, with inlet, ball valve, float and handle, 32mm dia PVC long bend flush pipe 90cm long and 15mm die 450mm including PVC connection with CP brass coupling nuts and PVC washers at bothy ends fixed compete all as specified and directed by Engr-in-Charge.

Vitreous chinaware squantting pan, ''Orrisa pattern'', size 580mm x 440mm white, with Cast iron 'P' or 'S' trap, front or back inlet, integral footrest excluding flushing cistern and flush type, etc and making good to floors (fixed in repair) complete all as specified and directed by Engr-in-Charge.

Dismantling water tanks of capacity exc. 250 ltrs & n.exc 500 ltrs, complete all as specified and directed by Engr-in-Charge.

Rotational moulded polyethylene water storage tank 500 Ltrs capacity (cylinderical vertical with closed top) including 15mm brass float valve & fly nut and make hoisted and fixed in position, complete all as specified and directed by Engr-in-Charge.

Plain cement concrete, 75mm thick, M-7.5 (nominal mix), type D-2 (using 40mm graded crushed stone aggregate) as in sub base and similar work complete all as specified and directed by Engr-in- Charge.

Chequered cement concrete tiles machine pressed glossy finish (heavy duty) of size 20cmx20cmx25mm thick with grey cement and pigment set jointed & pointed in neat cement slurry in floors over 15mm thick screed bed in cement mortar 1:6 complete, all as specified and directed by Engr-in-Charge.

Taking up or down GI tubing 15mm bore in any position complete all as specified and directed by Engr-in-Charge.

Taking up or down GI tubing 20mm bore in any position complete all as specified and directed by Engr-in Charge.

GI tubing, medium grade,15mm bore with all fittings/ fixtures, laid under floors/ trenches or fixed in wall complete, all as specified and directed by Engr-in- Charge.

All as per items No. 57 but fixing only.

20mm bore GI tubing, medium grade, galvanised with all fittings and fixtures fixed to walls and celling or laid in floor, complete all as specified and directed by Engr-in- Charge.

All as per items No. 59 but fixing only.

15mm bore Bib taps (in repair) chromium plated, Brass with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule complete all as spcified and directed by Engr-in-Charge.

15mm bore, stop valves, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipes or for unions and fixed in repairs complete all as specified and directed by Engr-in- Charge.

Shower rose, 125mm Chromium plated, with or without swivel joints, any size, including fixing to steel pipe or union (fixed in repair) complete all as specified and directed by Engr-in-Charge.

15mm bore CP stop valve (fancy type) brass, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as spcified and directed by Engr-in-Charge.

Tubular towel rail, 20mm dia, D-type, 60cm long between flanges aluminium anodised, fixed in repairs complete all as specified and directed by Engr-in- Charge.

Dismantling of cast iron or reinforced concrete drains pipes, jointed in cement mortar and taking out of trenches, if required complete all as specified and directed by the Engr-in-Charge.

Cast iron floor trap, 75mm bore (fixed in repair), with grating including jointing to waste pipe fixed in cement concrete, M-15, type B-1, complete all as specified and as directed by Engineer-in- Charge.

100 mm bore, cast iron soil waste and vent pipe (sand cast) in any length with or without ears, with cement joints, laid in trenches or in floors, complete all as specified and directed by the Engr-in-Charge.

100 mm bore, cast iron soil waste and vent pipe (sand cast) in any length with or without ears, with cement joints, fixed to walls etc with brackets / clamps complete all as specified and directed by the Engr-in-Charge.

75mm bore, cast iron soil waste and vent pipe (sand cast) in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed by the Engr-in-Charge.

75mm bore, cast iron soil waste and vent pipe (sand cast) in any length with or without ears, with cement joints, fixed to walls etc with brackets / clamps complete all as specified and directed by the Engr-in-Charge.

50mm bore, cast iron soil waste and vent pipe (sand cast) in any length with or without ears, with cement joints, fixed to walls etc with brackets / clamps complete all as specified and directed by the Engr-in-Charge.

Cast Iron Cowls, 50mm dia complete all as specified and directed by the Engr-in-Charge

100mm bore sand cast iron P or S trap, complete all as specified and as directed by Engineer-in-Charge .

Cast iron floor trap, 100mm bore, with grating including jointing to waste pipe fixed in cement concrete, M-15, type B-1 (fixed in repair), complete all as specified and as directed by Engineer-in-Charge .

75mm bore Cast iron bends (any radius) with duck's foot or heel rest, (fixed in repair), complete all as specified and as directed by Engineer-in-Charge .

75mm bore cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, (fixed in repair), complete all as specified and as directed by Engineer-in-Charge .

100mm bore Cast iron bends (any radius) with duck's foot or heel rest, (fixed in repair), complete all as specified and as directed by Engineer-in-Charge.

100mm bore cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, (fixed in repair), complete all as specified and as directed by Engineer-in-Charge .

Plain cement concrete, M-15, nominal mix, type B-1, (using 20mm graded crushed stone aggregates), as in coping, complete all as specified and directed by the Engr-in-Charge.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof covering complete, all as specified and directed by Engr-in- Charge.

Galvanized corrugated mild steel sheeting, 0.63 mm thick with two corrugations side lap, fixed with ' L' or 'J' hooks and washers, as in roof covering with grade of zinc coating 275, complete all as specified and directed by Engr-in- Charge.

Plain GaIvanised mild steel sheeting 0.63 mm thick, as in ridges, valley, gutter etc; fixed with L-type or J type hooks and washers, complete all as specified and directed by Engr-in-Charge.

Taking down roof trusses, coupled rafters or trussed beams, clear span upto 04 metres for renewal of any defective members & reassembling, housing & fixing trusses etc; after repair, including tightning up wedges, cotters bolts etc; complete all as specified and directed by Engr-in-Charge.

Dismantling timber scantling unframed work under 40 sqcm as in rails, purlins & rafters complete all as spcified and directed by Engr-in-Charge.

Second class, soft wood, wrought, framed work as in repair of trusses, purlins etc; complete all as specified and directed by Engr-in-Charge.

All as per serial item No. 86 here-in-above but refixing only.

Dismantling wrought iron or mild steel work of any description not otherwise provided, complete all as Specified and directed by Engr-in-Charge.

Mild steel work as in wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed by Engr-in-Charge.

Preparing surfaces of wood and wood based materials new or old, of any description and girth, not other wise described and treated with two coats of creosote oil complete all as specified and directed by Engr-in-charge.

Dismentling asbestos cement sheets as in ceiling complete all as specified and directed by Engr-in-Charge.

4mm thick Non Asbestos Cement fibre building board, fixed or laid to MS frame work as in ceilling complete all as specified and directed by Engr-in- Charge.and directed by Engr-in-Charge.

Two coats of white wash on ceilling including prepration of AC ceiling surfaces complete all as spcified and directed by Engr-in-Charge.

Demolition of brick work or stone/ boulders masonry, built in cement mortar including all quoins, arches, pillars, etc but excluding ashlar facings dressed stone work and precast concrete articles, complete all as specified and directed by the Engr-in-Charge.

Walling of random rubble stone masonry, uncoursed, well bonded, bedded and solidly hearted built in CM 1:6 Complete all as specified and directed by Engr-in- Charge.

All as per item No 95 here-in-above but except stones.

Brick work with sub class 'B' bricks, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:4 complete all as specified and directed by the Engr-in-Charge.

Dismantling old timber scantling 40 Sqcm and over in section, in any position complete all as specified and directed by the Engr-in-Charge

2nd class soft wood plain fillets, square, rectangular or triangular in section and secured with nails, sectional area exceeding 6 sqcm but not exceeding 13 sqcm complete all as specified and as directed by Engr-in-Charge.

Two coats of synthetic enamel paint over a coat of pink primer on new wood or wooden based surfaces of any description, area not exceeding 10cm width or girth including preparation of surfaces complete, all as specified and directed by Engr-in- Charge.

Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete with fittings and fixtures such as switches, ceiling roses, pendants, regulators, socket, lamp holders brackets, bulk head fittings etc including removing material for taking credit ( credit shall be recovered as per credit Schedule attached) and also making good disturbed surfaces of wall, floors etc all as specified and as directed by the Engineer-in-Charge.

Point wiring with 1.5 Sqmm copper conductor (Multi-stranded) PVC insulated and unsheathed FRLS electric cable 1100 volts cable and including PVC casing and caping of suitable size (as per conductor run) with all fittings/ accessories and including PVC insulated electric cable 1100 volts 1.5 Sqmm ( multi-stranded) copper conductor single core( Green colour) cable as continuous earth wire connected to common earth dolly including wooden box covered with 3 mm thick plastic laminated sheet ( Make Hylum) for one light point/ fan/exhaust fan point/ bell point etc controlled by one, one way switch,complete all as specified and as directed by the Engineer-in-Charge.

All as per item No 102 here-in-above, but for one 3 pin socket outlet 5 Amp on the same board with other switches complete all as specified and as directed by the Engineer-in-Charge.

All as per item No 102 here-in-above, but for one 3 pin socket outlet 5 Amp on independent board complete all as specified and as directed by the Engineer-in-Charge.

All as per serial item No 102 here-in-before, but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor ( Multi-stranded) PVC insulated and unsheathed electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 2.5 Sqmm copper stranded conductor as continuous earth wire connected to common earth dolly complete all as specified and as directed by Engineer-in-Charge.

Socket outlet 2 in 1, 3 pin, 5 Amp, flush type complete all as specified and as directed by the Engineer-in-Charge.

Socket outlet 2 in 1, 3 pin, 5 Amp and 15 Amp, flush type complete all as specified and as directed by the Engineer-in-Charge.

Switch piano, flush type, single pole, one way, 15Amp, complete all as specified and as directed by the Engineer-in-Charge.

Switch piano, flush type, single pole, one way, 5/6 Amp,complete all as specified and as directed by the Engineer-in-Charge.

Bell push switch, flush button, single pole, one way 5 Amps complete all as specified and as directed by the Engineer-in-Charge.

Call bell ding dong AC 230 volt single pole complete all as specified and as directed by Engineer-in-Charge.

Sub main wiring, two single core, PVC insulated and unsheathed cable with 6 Sqmm multi -strand copper conductor drawing in PVC casing caping with 4 Sqmm PVC copper conductor cable as in earth wire system, complete all as specified and as directed by the Engineer-in-Charge.

Ceiling rose surface type, 65 mm x 50 mm two to three terminals / PVC / polycarbonate, isolated body fixed on PVC block complete all as specified and as directed by Engineer-in-Charge.

Replacement of existing unserviceable Sheet metal enclosure with new DB’s suitable for MCBs of single pole and neutral 12 way double door type with 200 amp rated bus bar complete all specified and as directed by the Engineer-in-Charge. Note: (i) Connnections of the MCB'S shall be done with appropriate size of brass/Cooper thimble. (ii) The disturbed surface shall be match with existing surface. Make: Hensal/Legrand/Heggars

MCB SPN 40Amp breaking capacity 10KA, complete all as specified and directed by the Engineer-in-Charge.

MCB SPN 6-32 Amp complete all as specified and directed by the Engineer-in-Charge.

Universal batten for LED tube suitable for indoor applications tube light fitting 4Ft, 1x18W complete all specified and as directed by the Engineer-in-Charge. Make:- Havells Cat part No. REGALBATTENT5UPTO1X18WDSBSWH or equivalent in Philips/OSRAM/Bajaj.

LED tubelight with very high efficacy suited for installation in existing batten all as specified and as directed by the Engineer-in-Charge. Make: Havells CAT Part No. CRYSTAL1213T8DSTL8WLED865S-GLASS or equivalent in Philips/OSRAM/Bajaj.

Engery efficient LED integrated batten suitable for indoor applications tube light fitting 1x10 Watt 2 FT complete all as specified and as directed by the Engineer-in-Charge. Make:- Havells Cat part No. LUMILINEPLUSBS10WLED865SPCSS or equivalent in Philips/OSRAM/Bajaj.

1x30 watt LED Bldg security light fitting with lamp pressure die cast housing with epoxy powder coated dark graphite grey colour finish, prismatic polycarbonate cover with individual LED lenses with GI pipe 1.5 mtr length clamps, nuts, bolts complete all as specified and directed by Engr-in-charge. Make:- Havells Cat part No. ENDURAPEALSL30WLED757SASYTOPCMP OR equivalent inSurya/bajaj.

Angular type lamp holder, PVC/ polycarbonate type with back plate suitable for 15/18 watts for batten fitting, including plastic square board of required size complete all specified and as directed by the Engineer-in-Charge.

LED Lamp,pin type,9watt, complete all specified and as directed by the Engineer-in-Charge. MAKE: Polycab cat part No. LLP0101051 AELIUS LX LED Lamp 9W BC 6500K or equivalent in Bajaj/ CG/ Havells.

Taking down and re-fixing, connecting existing serviceable electric meters, single phase complete all specified and as directed by the Engineer-in-Charge.

Earthing complete with galvanized steel earth plate electrode 600x600x6mm thick burried directly in ground(earth plate not less than 2.25 mtr deep below the normal ground level ) with top edge of plate not less than 1.5 mtr below the normal ground level connected to galvanized earth lead wire 4mm dia by means of nuts bolts,washers,check nuts of iron or steel including test point PCC pits and RCC cover in PCC 1:2:4 (type B-1) including iron angle frme 40x40x6mm and medium grade GI watering pipe 20mm dia with funnel and wire mesh and 15 mm bore GI pipe light grade proection pipe including excavation and charcoal ,common salt surrounded with 15cm all around the plate complete all as specified and shown in EP-3 of SSR Part-I & as directed by Engr-in-Charge.

Supply, jointing, fixing or passing through pipe, trenches or ducts,commissioning and testing XLPE insulated screened and PVC sheathed armoured electric power LT cable heavy duty with aluminium conductor nominal cross sectional area 25 Sqmm 3.5 core for working voltage upto including 1100 volts confirming to IS - 7098 (Part-I) 1988 (Compaction condutors shall be shaped and arrangement for the same shall be on the cable), including taking down existing cables, complete all as specified & directed by Engr-in-Charge.

Excavation in trenches not exc 1.5 mtr wide and not exceeding 1.5 mtr in depth and getting out in any type of soil, for laying of cable , erection of poles and stays etc, complete all as specified & directed by Engr-in-Charge.

Returning, filling in, including spreading,,levelling,,watering and well ramming in layers n.exc 25 cm thick, complete all as specified & directed by Engr-in-Charge.

Removal of surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above starting point, complete all as specified & directed by Engr-in-Charge.

Sand cushioning to underground cables complete all as specified in clause 19.75 of SSR Part-I laid before and after laying of cables,complete all as specified.

Sub class 'B' bricks, old size, brick covering, laid dry, flat transversally along the length of cable on sand cushioning, with width equal to the length of the brick complete all as specified and directed.

GI tubing, light grade, 40mm bore with all fittings laid in trenches or under road crossing or fixed along trenches/walls as protection pipe with clamps, nuts, washer, bolts (where necessary) as per reqmt of site complete all as specified & directed by Engr-in-Charge.

Supply & fix (in replacement) of existing unserviceable Sheet metal enclosure with DB’s suitable for MCBs of triple pole and neutral, 4 way, 415 volt, double door type with 200 amp rated bus bar double door type with one incoming and 12 outgoing complete all specified and as directed by the Engineer-in-Charge. Make: Havells/Legrand/ABB Note: (i) Connnections of the MCB'S shall be done with appropriate size of brass/Cooper thimble. (ii) The disturbed surface shall be match with existing shall be part of job.

Supply and fix (in replacement) of MCB TPN 63 Amps ( 01 incoming+04 outgoing ) complete all specified and as directed by the Engineer-in-Charge.

Sheet metal enclosure of size 450x300x180mm made out of 2mm thick MS sheet suitable for fixing the MCB DB & meters, single door type with locking arrangement and reconnecting commissioning including two coats of synthetic enamel paint over a coat of red oxide primer to internal and external surfaces with machine spray, necessary cutting, PCC work, including match the disturbed surface to existing surface complete complete all specified and as directed by the Engineer-in-Charge.

Geyser (water heater storage type), electrical, capacity 25 litres. BEE 5 star rated, vertical type including giving inlet & outlet connections, testing, commissioning complete all as specified and as directed by the Engineer-in-Charge. Make: Jaquar model Elena/ Racold Model ALTRO 2/ Venus model wave. Note: Fixing of electric geyser on wall with suitable size of Anchor bolt including grouting in PCC, making good the disturbed surface shall be part of the job at no extra cost.

malghotra construction co

jatindera enterprises