BID DOCUMENT FOR PROVIDING, SUPPLY, INSTALLATION, TESTING, COMMISSIONING OF GRID CONNECTED ROOFTOP SOLAR PROJECT WITH (05 YEAR) OPERATION AND MAINTENANCE, AND AUTOMETIC SOLAR CLEANING SYSTEM IN VARIOUS AREA AT PADRA NAGARPALIKA UNDER: SWARNIM JAYANTI MUKHYA MANTRI SHEHRI VIKAS YOJANA YEAR: 2025 26.

Total Amount Rs.

Note : 4 In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-

10/2017 Cement Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where

there is a change as per actual mix design the cost of difference of cement consumption have been deducted

from the rate of original item at the rate of input rate mentioned in all the tender.

SECTION-7 BILL OF QUANTITIES-183

Signature of Contractor President Chief Officer

Padra Nagarpalika Padra Nagarpalika

SECTION-7 BILL OF QUANTITIES-184

PADRA NAGARPALIKA PADRA

NAME OF WORK : ESTIMATE FOR SUPPLY, INSTALLATION, TESTING, COMMISSIONING OF 21 KW GRID

CONNECTED ROOFTOP SOLAR PROJECT WITH 05 YEAR O & M,AND AUTOMETIC SOLAR CLEANING SYSTEM AT

SAYAJI GARDEN WATER WORKS , AT PADRA DIST. VADODARA

Item No. & Description Qty. Per Amount

Supply, Installation, Testing & Commissioning of following size of Grid Tied Solar Power Plant with

Solar Panels (ALMM approved): Frame Material : Anodized Aluminum alloy Frame With Twin Wall Profile, Front Cover :

High Transmission Low-Iron Tempered Glass (AR Coated), High efficency and positive power tolerance Pmax: 0/+5, Module

Efficiency should be approx. 19.5%-22%, Normal operating temperature 45'C, Junction Box with Waterproof IP67 & MC4

Compatible and Enclosed with Bypass diodes, 100% Electroluminescence test to ensure error free Modules, Thep. temp. co-

efficient of the PV module shall equal or better than -0.45%/degree C. Solar PV modules of minimum fill factor 75% to be

used. Unit Production:- More than 4.5 Unit /kw /day (Actual)(1Year Avg) With 10 year Product warranty and 25 year Linear

Power Warranty includes all mechanical and electrical parameters of the Solar panel. Modules must be complied to the

DCR(Domestic content requirements). The Ration of AC to DC is 5:6 for the Installation capacity which are given in AC KW.

Solar Inverter: MPPT Range: MPPT Range: 80-1000 V , Max efficiency: 97.5% - 98.9%, O/p Frequency: 50/60Hz, Operating

Altitude (m) ≤4000, O/p Power Factor: ~1, O/P THDi: <3%, Operating Tempreture Range: -25~60°C, Integrated protection of

Inverter are Anti-islanding Protection, Input Reverse Polarity Protection, Insulation Resistor Detection, Ground fault

protection, Residual Current Monitoring Unit, Output Over Current Protection, Output Short Circuit Protection, Output

Over Voltage Protection, PV array string fault Protection. Protection Degree: IP65, User Interface LCD & APP, Datalogger &

Communication: GPRS / Wi-Fi.

Integrated, Input Reverse Polarity Protection Integrated, Insulation Resistor Detection Integrated, Residual Current

Monitoring Unit Integrated, Output Over Current Protection Integrated, Output Short Circuit Protection Integrated, Output

Over Voltage Protection Integrated, Protection Degree: IP65, User Interface LCD & APP,Datalogger & Communication:

GPRS / Wi-Fi, Module Mounting Structure: The mounting (Rectangular pipe / square pipe / circular pipe) with requisite

cross bars, nuts and bolts, etc. shall be Hot deep galvanized with minimum 80micron coating. The Rectangular / square

/circular hollow pipe section used for the structure should have a minimum thickness of 2.0 mm. other than above, the

material thickness should be minimum 2.5 mm. A certificate of a structural engineer certifying the strength and stability of

the mounting structure to withstand the weight and wind speed of 150 km/hour throughout the life span of 25 years of

the system, shall be submitted by the vendors. Hot Dipped Galvanized steel coils. suitable arrangement for base plate for

foundation , solar panel mounting, the structure should be suitable for carry the load of solar panel,wiring, sprinkler

system etc. with necessary foundation work/wall mount, j bolt, anchor fastner etc. the nut bolt used for installtion of

stucture should be (SS 304) quality.The ground clearance of the bottom most edge of solar panel shall not be less than

mm to 1200 mm or as per site’s technical/feasibility requirement.

a. Column –The minimum section (thickness) should be 60MM*40MM

b. Rafter - The minimum section (thickness) should be 60MM*40MM

c. Purlin - The minimum section (thickness) should be 40MM * 40MM Balane of System with necessary Swichgears

(Suitabel size and protection of ACDB & DCDB), inter connecting wiring, earthing system as per the CEIG drawing approval,

lightining arrester system as per the CEIG drawing approval, all liasoning work with various gov. dipartment like state nodal

agency,DISCOM & CEIG is included in agency scope

(Excluding All charges namely GEDA Application fees, Solar connectivity Charges, Meter connectivity Charges, Meter

(C ) Grid Tied Solar Power System: 11 - 25 kW (3 - phase)

SBD SECTION-7 BILL OF QUANTITIES-185

Item No. & Description Qty. Per Amount

The all inclusive comprehencive annual maintance contract cost covers yearly maintanance of solar Pv Modules, Inverter,

wiring,earthing,switchgears, etc with material and labour cost including preventive maintanance.The cost covers entire

installation. AMC also includes monthly site visit and inspection of project with submission of inspection and solar

generation report. All parts should be replaced/repaired if found faulty within specified time. Agency has to provide

necessory licening work for warranty,power,Bidirectional meter etc

(C ) 21KW-50KW System

1St year 21.00 4078.38 KW

2nd Year 21.00 4078.38 KW

3Rd Year 21.00 4078.38 KW

4Th Year 21.00 4078.38 KW

5Th Year 21.00 4078.38 KW

Providing & erecting Automatic solar panel cleaning system for solar

power projects which includes necessary plumbing work (UPVC pipes

and accessories) from source of water to project site (upto

meters),Suitable size of sub mercible/ open well motor, necessary wiring

for motor and sprinkler system with safety, timer circuit for

automatically on/off the sprinkler system, necessary size oand number

of nozzles/JET (minimum 1 Nozzle/Jet per module).

(D) 21KW-50KW Cleaning System

Total Amount Rs. ..............

Total Amount Rs. ..............

Meter connectivity Charges Rs…...…......

Add GEDA Application fees Rs…...…......

Meter Testing Charges and system stability/strenthning charges. Rs…...…......

Amount Rs. ..............

Add 18% GST Charge Rs…...…......

Net Amount Rs. ..............

SBD SECTION-7 BILL OF QUANTITIES-186

PADRA NAGARPALIKA PADRA

NAME OF WORK : ESTIMATE FOR SUPPLY, INSTALLATION, TESTING, COMMISSIONING OF 4.00 KW GRID CONNECTED

ROOFTOP SOLAR PROJECT WITH 05 YEAR O & M AT AMBAJI POND , TA PADRA DIST. VADODARA

Item No. & Description Qty. Per Amount

Supply, Installation, Testing & Commissioning of following size of Grid Tied Solar Power Plant with

Solar Panels (ALMM approved): Frame Material : Anodized Aluminum alloy Frame With Twin Wall Profile, Front Cover : High

Transmission Low-Iron Tempered Glass (AR Coated), High efficency and positive power tolerance Pmax: 0/+5, Module Efficiency

should be approx. 19.5%-22%, Normal operating temperature 45'C, Junction Box with Waterproof IP67 & MC4 Compatible and

Enclosed with Bypass diodes, 100% Electroluminescence test to ensure error free Modules, Thep. temp. co-efficient of the PV

module shall equal or better than -0.45%/degree C. Solar PV modules of minimum fill factor 75% to be used. Unit Production:- More

than 4.5 Unit /kw /day (Actual)(1Year Avg) With 10 year Product warranty and 25 year Linear Power Warranty includes all

mechanical and electrical parameters of the Solar panel. Modules must be complied to the DCR(Domestic content requirements).

The Ration of AC to DC is 5:6 for the Installation capacity which are given in AC KW.

Solar Inverter: MPPT Range: MPPT Range: 80-1000 V , Max efficiency: 97.5% - 98.9%, O/p Frequency: 50/60Hz, Operating Altitude

(m) ≤4000, O/p Power Factor: ~1, O/P THDi: <3%, Operating Tempreture Range: -25~60°C, Integrated protection of Inverter are Anti-

islanding Protection, Input Reverse Polarity Protection, Insulation Resistor Detection, Ground fault protection, Residual Current

Monitoring Unit, Output Over Current Protection, Output Short Circuit Protection, Output Over Voltage Protection, PV array string

fault Protection. Protection Degree: IP65, User Interface LCD & APP, Datalogger & Communication: GPRS / Wi-Fi.

Integrated, Input Reverse Polarity Protection Integrated, Insulation Resistor Detection Integrated, Residual Current Monitoring Unit

Integrated, Output Over Current Protection Integrated, Output Short Circuit Protection Integrated, Output Over Voltage Protection

Integrated, Protection Degree: IP65, User Interface LCD & APP,Datalogger & Communication: GPRS / Wi-Fi, Module Mounting

Structure: The mounting (Rectangular pipe / square pipe / circular pipe) with requisite cross bars, nuts and bolts, etc. shall be Hot

deep galvanized with minimum 80micron coating. The Rectangular / square /circular hollow pipe section used for the structure

should have a minimum thickness of 2.0 mm. other than above, the material thickness should be minimum 2.5 mm. A certificate of a

structural engineer certifying the strength and stability of the mounting structure to withstand the weight and wind speed of

km/hour throughout the life span of 25 years of the system, shall be submitted by the vendors. Hot Dipped Galvanized steel coils.

suitable arrangement for base plate for foundation , solar panel mounting, the structure should be suitable for carry the load of solar

panel,wiring, sprinkler system etc. with necessary foundation work/wall mount, j bolt, anchor fastner etc. the nut bolt used for

installtion of stucture should be (SS 304) quality.The ground clearance of the bottom most edge of solar panel shall not be less than

300 mm to 1200 mm or as per site’s technical/feasibility requirement.

a. Column –The minimum section (thickness) should be 60MM*40MM

b. Rafter - The minimum section (thickness) should be 60MM*40MM

c. Purlin - The minimum section (thickness) should be 40MM * 40MM Balane of System with necessary Swichgears (Suitabel size and

protection of ACDB & DCDB), inter connecting wiring, earthing system as per the CEIG drawing approval, lightining arrester system as

per the CEIG drawing approval, all liasoning work with various gov. dipartment like state nodal agency,DISCOM & CEIG is included in

(Excluding All charges namely GEDA Application fees, Solar connectivity Charges, Meter connectivity Charges, Meter testing Charges

(A) Grid Tied Solar Power System: 1 - 6 kW

The all inclusive comprehencive annual maintance contract cost covers yearly maintanance of solar Pv Modules, Inverter,

wiring,earthing,switchgears, etc with material and labour cost including preventive maintanance.The cost covers entire installation.

AMC also includes monthly site visit and inspection of project with submission of inspection and solar generation report. All parts

should be replaced/repaired if found faulty within specified time. Agency has to provide necessory licening work for

warranty,power,Bidirectional meter etc

SBD SECTION-7 BILL OF QUANTITIES-187

Item No. & Description Qty. Per Amount

(A) 1KW-10KW System

1St year 4.00 5564.09 KW

2nd Year 4.00 5564.09 KW

3Rd Year 4.00 5564.09 KW

4Th Year 4.00 5564.09 KW

5Th Year 4.00 5564.09 KW

Providing & erecting Automatic solar panel cleaning system for solar power

projects which includes necessary plumbing work (UPVC pipes and accessories)

from source of water to project site (upto 30 meters),Suitable size of sub

mercible/ open well motor, necessary wiring for motor and sprinkler system with

safety, timer circuit for automatically on/off the sprinkler system, necessary size

oand number of nozzles/JET (minimum 1 Nozzle/Jet per module).

(A) 1KW-5KW Cleaning System

Total Amount Rs. ..............

Total Amount Rs. ..............

Meter connectivity Charges Rs…...…......

Add GEDA Application fees Rs…...…......

Meter Testing Charges and system stability/strenthning charges. Rs…...…......

Amount Rs. ..............

Add 18% GST Charge Rs…...…......

Net Amount Rs. ..............

SBD SECTION-7 BILL OF QUANTITIES-188

PADRA NAGARPALIKA PADRA

NAME OF WORK : ESTIMATE FOR SUPPLY, INSTALLATION, TESTING, COMMISSIONING OF 36 KW GRID CONNECTED

ROOFTOP SOLAR PROJECT WITH 05 YEAR O & M AT WATER WORKS NEAR AMBAJI TEMPLE , TA PADRA DIST.

Item No. & Description Qty. Per Amount

Supply, Installation, Testing & Commissioning of following size of Grid Tied Solar Power Plant with

Solar Panels (ALMM approved): Frame Material : Anodized Aluminum alloy Frame With Twin Wall Profile, Front Cover : High

Transmission Low-Iron Tempered Glass (AR Coated), High efficency and positive power tolerance Pmax: 0/+5, Module Efficiency

should be approx. 19.5%-22%, Normal operating temperature 45'C, Junction Box with Waterproof IP67 & MC4 Compatible and

Enclosed with Bypass diodes, 100% Electroluminescence test to ensure error free Modules, Thep. temp. co-efficient of the PV module

shall equal or better than -0.45%/degree C. Solar PV modules of minimum fill factor 75% to be used. Unit Production:- More than

Unit /kw /day (Actual)(1Year Avg) With 10 year Product warranty and 25 year Linear Power Warranty includes all mechanical and

electrical parameters of the Solar panel. Modules must be complied to the DCR(Domestic content requirements). The Ration of AC to

DC is 5:6 for the Installation capacity which are given in AC KW.

Solar Inverter: MPPT Range: MPPT Range: 80-1000 V , Max efficiency: 97.5% - 98.9%, O/p Frequency: 50/60Hz, Operating Altitude (m)

≤4000, O/p Power Factor: ~1, O/P THDi: <3%, Operating Tempreture Range: -25~60°C, Integrated protection of Inverter are Anti-

islanding Protection, Input Reverse Polarity Protection, Insulation Resistor Detection, Ground fault protection, Residual Current

Monitoring Unit, Output Over Current Protection, Output Short Circuit Protection, Output Over Voltage Protection, PV array string

fault Protection. Protection Degree: IP65, User Interface LCD & APP, Datalogger & Communication: GPRS / Wi-Fi.

Integrated, Input Reverse Polarity Protection Integrated, Insulation Resistor Detection Integrated, Residual Current Monitoring Unit

Integrated, Output Over Current Protection Integrated, Output Short Circuit Protection Integrated, Output Over Voltage Protection

Integrated, Protection Degree: IP65, User Interface LCD & APP,Datalogger & Communication: GPRS / Wi-Fi, Module Mounting

Structure: The mounting (Rectangular pipe / square pipe / circular pipe) with requisite cross bars, nuts and bolts, etc. shall be Hot

deep galvanized with minimum 80micron coating. The Rectangular / square /circular hollow pipe section used for the structure

should have a minimum thickness of 2.0 mm. other than above, the material thickness should be minimum 2.5 mm. A certificate of a

structural engineer certifying the strength and stability of the mounting structure to withstand the weight and wind speed of

km/hour throughout the life span of 25 years of the system, shall be submitted by the vendors. Hot Dipped Galvanized steel coils.

suitable arrangement for base plate for foundation , solar panel mounting, the structure should be suitable for carry the load of solar

panel,wiring, sprinkler system etc. with necessary foundation work/wall mount, j bolt, anchor fastner etc. the nut bolt used for

installtion of stucture should be (SS 304) quality.The ground clearance of the bottom most edge of solar panel shall not be less than

300 mm to 1200 mm or as per site’s technical/feasibility requirement.

a. Column –The minimum section (thickness) should be 60MM*40MM

b. Rafter - The minimum section (thickness) should be 60MM*40MM

c. Purlin - The minimum section (thickness) should be 40MM * 40MM Balane of System with necessary Swichgears (Suitabel size and

protection of ACDB & DCDB), inter connecting wiring, earthing system as per the CEIG drawing approval, lightining arrester system as

per the CEIG drawing approval, all liasoning work with various gov. dipartment like state nodal agency,DISCOM & CEIG is included in

(Excluding All charges namely GEDA Application fees, Solar connectivity Charges, Meter connectivity Charges, Meter testing Charges

(D) Grid Tied Solar Power System: 26 - 50 kW (3 - phase)

The all inclusive comprehencive annual maintance contract cost covers yearly maintanance of solar Pv Modules, Inverter,

wiring,earthing,switchgears, etc with material and labour cost including preventive maintanance.The cost covers entire installation.

AMC also includes monthly site visit and inspection of project with submission of inspection and solar generation report. All parts

should be replaced/repaired if found faulty within specified time. Agency has to provide necessory licening work for

warranty,power,Bidirectional meter etc

SBD SECTION-7 BILL OF QUANTITIES-189

Item No. & Description Qty. Per Amount

(C ) 21KW-50KW System

1St year 36.00 4280.38 KW

2nd Year 36.00 4280.38 KW

3Rd Year 36.00 4280.38 KW

4Th Year 36.00 4280.38 KW

5Th Year 36.00 4280.38 KW

Providing & erecting Automatic solar panel cleaning system for solar power projects

which includes necessary plumbing work (UPVC pipes and accessories) from source

of water to project site (upto 30 meters),Suitable size of sub mercible/ open well

motor, necessary wiring for motor and sprinkler system with safety, timer circuit for

automatically on/off the sprinkler system, necessary size oand number of

nozzles/JET (minimum 1 Nozzle/Jet per module).

(D) 21KW-50KW Cleaning System

Total Amount Rs. ..............

Total Amount Rs. ..............

Meter connectivity Charges Rs…...…......

Add GEDA Application fees Rs…...…......

Meter Testing Charges and system stability/strenthning charges. Rs…...…......

Amount Rs. ..............

Add 18% GST Charge Rs…...…......

Net Amount Rs. ..............

SBD SECTION-7 BILL OF QUANTITIES-190

PADRA NAGARPALIKA PADRA

NAME OF WORK : ESTIMATE FOR SUPPLY, INSTALLATION, TESTING, COMMISSIONING OF 60 KW GRID CONNECTED

ROOFTOP SOLAR PROJECT WITH 05 YEAR O & M AT SBM SITE-AT SAREJA TOWN , TA PADRA DIST. VADODARA

Item No. & Description Qty. Per Amount

Supply, Installation, Testing & Commissioning of following size of Grid Tied Solar Power Plant with

Solar Panels (ALMM approved): Frame Material : Anodized Aluminum alloy Frame With Twin Wall Profile, Front Cover : High

Transmission Low-Iron Tempered Glass (AR Coated), High efficency and positive power tolerance Pmax: 0/+5, Module Efficiency

should be approx. 19.5%-22%, Normal operating temperature 45'C, Junction Box with Waterproof IP67 & MC4 Compatible and

Enclosed with Bypass diodes, 100% Electroluminescence test to ensure error free Modules, Thep. temp. co-efficient of the PV

module shall equal or better than -0.45%/degree C. Solar PV modules of minimum fill factor 75% to be used. Unit Production:-

More than 4.5 Unit /kw /day (Actual)(1Year Avg) With 10 year Product warranty and 25 year Linear Power Warranty includes all

mechanical and electrical parameters of the Solar panel. Modules must be complied to the DCR(Domestic content requirements).

The Ration of AC to DC is 5:6 for the Installation capacity which are given in AC KW.

Solar Inverter: MPPT Range: MPPT Range: 80-1000 V , Max efficiency: 97.5% - 98.9%, O/p Frequency: 50/60Hz, Operating Altitude

(m) ≤4000, O/p Power Factor: ~1, O/P THDi: <3%, Operating Tempreture Range: -25~60°C, Integrated protection of Inverter are Anti-

islanding Protection, Input Reverse Polarity Protection, Insulation Resistor Detection, Ground fault protection, Residual Current

Monitoring Unit, Output Over Current Protection, Output Short Circuit Protection, Output Over Voltage Protection, PV array string

fault Protection. Protection Degree: IP65, User Interface LCD & APP, Datalogger & Communication: GPRS / Wi-Fi.

Integrated, Input Reverse Polarity Protection Integrated, Insulation Resistor Detection Integrated, Residual Current Monitoring Unit

Integrated, Output Over Current Protection Integrated, Output Short Circuit Protection Integrated, Output Over Voltage Protection

Integrated, Protection Degree: IP65, User Interface LCD & APP,Datalogger & Communication: GPRS / Wi-Fi, Module Mounting

Structure: The mounting (Rectangular pipe / square pipe / circular pipe) with requisite cross bars, nuts and bolts, etc. shall be Hot

deep galvanized with minimum 80micron coating. The Rectangular / square /circular hollow pipe section used for the structure

should have a minimum thickness of 2.0 mm. other than above, the material thickness should be minimum 2.5 mm. A certificate of

a structural engineer certifying the strength and stability of the mounting structure to withstand the weight and wind speed of

km/hour throughout the life span of 25 years of the system, shall be submitted by the vendors. Hot Dipped Galvanized steel coils.

suitable arrangement for base plate for foundation , solar panel mounting, the structure should be suitable for carry the load of

solar panel,wiring, sprinkler system etc. with necessary foundation work/wall mount, j bolt, anchor fastner etc. the nut bolt used

for installtion of stucture should be (SS 304) quality.The ground clearance of the bottom most edge of solar panel shall not be less

than 300 mm to 1200 mm or as per site’s technical/feasibility requirement.

a. Column –The minimum section (thickness) should be 60MM*40MM

b. Rafter - The minimum section (thickness) should be 60MM*40MM

c. Purlin - The minimum section (thickness) should be 40MM * 40MM Balane of System with necessary Swichgears (Suitabel size

and protection of ACDB & DCDB), inter connecting wiring, earthing system as per the CEIG drawing approval, lightining arrester

system as per the CEIG drawing approval, all liasoning work with various gov. dipartment like state nodal agency,DISCOM & CEIG is

included in agency scope

(Excluding All charges namely GEDA Application fees, Solar connectivity Charges, Meter connectivity Charges, Meter testing

(E) Grid Tied Solar Power System: 51 - 100 kW (3 - phase)

The all inclusive comprehencive annual maintance contract cost covers yearly maintanance of solar Pv Modules, Inverter,

wiring,earthing,switchgears, etc with material and labour cost including preventive maintanance.The cost covers entire installation.

AMC also includes monthly site visit and inspection of project with submission of inspection and solar generation report. All parts

should be replaced/repaired if found faulty within specified time. Agency has to provide necessory licening work for

warranty,power,Bidirectional meter etc

SBD SECTION-7 BILL OF QUANTITIES-191

Item No. & Description Qty. Per Amount

(D) 51KW-100KW System

1St year 60.00 3852.14 KW

2nd Year 60.00 3852.14 KW

3Rd Year 60.00 3852.14 KW

4Th Year 60.00 3852.14 KW

5Th Year 60.00 3852.14 KW

Providing & erecting Automatic solar panel cleaning system for solar power

projects which includes necessary plumbing work (UPVC pipes and accessories)

from source of water to project site (upto 30 meters),Suitable size of sub

mercible/ open well motor, necessary wiring for motor and sprinkler system with

safety, timer circuit for automatically on/off the sprinkler system, necessary size

oand number of nozzles/JET (minimum 1 Nozzle/Jet per module).

(E) 51KW-100KW Cleaning System

Total Amount Rs. ..............

Total Amount Rs. ..............

Meter connectivity Charges Rs…...…......

Add GEDA Application fees Rs…...…......

Meter Testing Charges and system stability/strenthning charges. Rs…...…......

Amount Rs. ..............

Add 18% GST Charge Rs…...…......

Net Amount Rs. ..............

SBD SECTION-7 BILL OF QUANTITIES-192

PADRA NAGARPALIKA PADRA

NAME OF WORK :ESTIMATE FOR SUPPLY, INSTALLATION, TESTING, COMMISSIONING OF 16 KW GRID CONNECTED

ROOFTOP SOLAR PROJECT WITH 05 YEAR O & M AT FULBAUG GARDEN , TA PADRA DIST. VADODARA

Item No. & Description Qty. Per Amount

Supply, Installation, Testing & Commissioning of following size of Grid Tied Solar Power Plant with

Solar Panels (ALMM approved): Frame Material : Anodized Aluminum alloy Frame With Twin Wall Profile, Front Cover : High

Transmission Low-Iron Tempered Glass (AR Coated), High efficency and positive power tolerance Pmax: 0/+5, Module Efficiency

should be approx. 19.5%-22%, Normal operating temperature 45'C, Junction Box with Waterproof IP67 & MC4 Compatible and

Enclosed with Bypass diodes, 100% Electroluminescence test to ensure error free Modules, Thep. temp. co-efficient of the PV

module shall equal or better than -0.45%/degree C. Solar PV modules of minimum fill factor 75% to be used. Unit Production:-

More than 4.5 Unit /kw /day (Actual)(1Year Avg) With 10 year Product warranty and 25 year Linear Power Warranty includes all

mechanical and electrical parameters of the Solar panel. Modules must be complied to the DCR(Domestic content requirements).

The Ration of AC to DC is 5:6 for the Installation capacity which are given in AC KW.

Solar Inverter: MPPT Range: MPPT Range: 80-1000 V , Max efficiency: 97.5% - 98.9%, O/p Frequency: 50/60Hz, Operating Altitude

(m) ≤4000, O/p Power Factor: ~1, O/P THDi: <3%, Operating Tempreture Range: -25~60°C, Integrated protection of Inverter are Anti-

islanding Protection, Input Reverse Polarity Protection, Insulation Resistor Detection, Ground fault protection, Residual Current

Monitoring Unit, Output Over Current Protection, Output Short Circuit Protection, Output Over Voltage Protection, PV array string

fault Protection. Protection Degree: IP65, User Interface LCD & APP, Datalogger & Communication: GPRS / Wi-Fi.

Integrated, Input Reverse Polarity Protection Integrated, Insulation Resistor Detection Integrated, Residual Current Monitoring Unit

Integrated, Output Over Current Protection Integrated, Output Short Circuit Protection Integrated, Output Over Voltage Protection

Integrated, Protection Degree: IP65, User Interface LCD & APP,Datalogger & Communication: GPRS / Wi-Fi, Module Mounting

Structure: The mounting (Rectangular pipe / square pipe / circular pipe) with requisite cross bars, nuts and bolts, etc. shall be Hot

deep galvanized with minimum 80micron coating. The Rectangular / square /circular hollow pipe section used for the structure

should have a minimum thickness of 2.0 mm. other than above, the material thickness should be minimum 2.5 mm. A certificate of

a structural engineer certifying the strength and stability of the mounting structure to withstand the weight and wind speed of

km/hour throughout the life span of 25 years of the system, shall be submitted by the vendors. Hot Dipped Galvanized steel coils.

suitable arrangement for base plate for foundation , solar panel mounting, the structure should be suitable for carry the load of

solar panel,wiring, sprinkler system etc. with necessary foundation work/wall mount, j bolt, anchor fastner etc. the nut bolt used

for installtion of stucture should be (SS 304) quality.The ground clearance of the bottom most edge of solar panel shall not be less

than 300 mm to 1200 mm or as per site’s technical/feasibility requirement.

a. Column –The minimum section (thickness) should be 60MM*40MM

b. Rafter - The minimum section (thickness) should be 60MM*40MM

c. Purlin - The minimum section (thickness) should be 40MM * 40MM Balane of System with necessary Swichgears (Suitabel size

and protection of ACDB & DCDB), inter connecting wiring, earthing system as per the CEIG drawing approval, lightining arrester

system as per the CEIG drawing approval, all liasoning work with various gov. dipartment like state nodal agency,DISCOM & CEIG is

included in agency scope

(Excluding All charges namely GEDA Application fees, Solar connectivity Charges, Meter connectivity Charges, Meter testing

(C ) Grid Tied Solar Power System: 11 - 25 kW (3 - phase)

The all inclusive comprehencive annual maintance contract cost covers yearly maintanance of solar Pv Modules, Inverter,

wiring,earthing,switchgears, etc with material and labour cost including preventive maintanance.The cost covers entire installation.

AMC also includes monthly site visit and inspection of project with submission of inspection and solar generation report. All parts

should be replaced/repaired if found faulty within specified time. Agency has to provide necessory licening work for

warranty,power,Bidirectional meter etc

SBD SECTION-7 BILL OF QUANTITIES-193

Item No. & Description Qty. Per Amount

(C ) 11KW-20KW Cleaning System

1St year 16.00 3681.45 KW

2nd Year 16.00 3681.45 KW

3Rd Year 16.00 3681.45 KW

4Th Year 16.00 3681.45 KW

5Th Year 16.00 3681.45 KW

Providing & erecting Automatic solar panel cleaning system for solar power

projects which includes necessary plumbing work (UPVC pipes and accessories)

from source of water to project site (upto 30 meters),Suitable size of sub

mercible/ open well motor, necessary wiring for motor and sprinkler system with

safety, timer circuit for automatically on/off the sprinkler system, necessary size

oand number of nozzles/JET (minimum 1 Nozzle/Jet per module).

(B) 11KW-20KW System

Total Amount Rs. ..............

Total Amount Rs. ..............

Meter connectivity Charges Rs…...…......

Add GEDA Application fees Rs…...…......

Meter Testing Charges and system stability/strenthning charges. Rs…...…......

Amount Rs. ..............

Add 18% GST Charge Rs…...…......

Net Amount Rs. ..............

SBD SECTION-7 BILL OF QUANTITIES-194