SPECIAL REPAIR TO 03 X TOILETS IN SARVATRA CSD CANTEEN BLDG NO T 20 AT RAIWALA MIL STN

Amount

Dismantling of asbestos cement ( corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coated GI based corrugated steel sheet 0.50mm thick of any colour, having tensile strength of 550 Mpa, AZ-150 as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Dismantling of timber scantling such as in fillets, rails, runner, rafters, purlins etc under 40 sqcm in section as in framed work complete all as specified and as directed.

S&F rolled mild steel section for structural steel work as in main and cross beams, hip and jack rafters, purlin where connected to common rafters and running rails and guides for sliding crane, fixed with angle cleats or other connecting plates/ bolts, conforming to Fe-290(Gde-E-165) complete all as specified and as directed. Note : The rates quoted allow for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete.

Demolition of PCC in ground floor and pavings not exc 15 cm thickness below or above ground level including removal of rubbish out side MOD land complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6), type C-2 using 40mm graded stone aggregate as in plinth protection, surface finished even & smooth without using extra cement, with and including joint filling (Size 30mm deep x 10mm wide) with sealing compound grade-A at 3m interval and corner complete all as specified and directed. Note : Joint to be provided at each interval of 3m and corner and cost of the same deemed included in quoted rate.

Demolition of concrete of any description and in any position not otherwise specifically provided for Cement concrete ( reinforced) including removal of debris etc to a distance out side MoD land complete all as specified and directed.

M&L for precast RCC (1:2:4) type B1, (using 20mm graded stone aggregates) as in cover slab (for manholes) and set in CM (1:4) including necessary fair finish formwork complete all as specified and directed.

M&L for mild steel TMT bars as in reinforcement, 10mm dia and over cut to length, bent to shape required including cranking, bending spirally for hopping for columns hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins,arches, pillars,etc. but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L for brick work with old size full brick subclass ‘B’ burnt clay bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed.

M&L for brick work with old size half brick subclass ‘B’ burnt clay bricks, straight or curved on plan exc 6m mean radius, built in CM (1:4) complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises from MoD land complete all as specified and as directed.

M&L for non skid, joint free, coloured ceramic tiles 7-8mm thick (Square/Rectunglar), as in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the coloured tiles laid with and including over 15mm thick screed bed in CM (1:6), area of each tiles shall be of following complete all as specified and directed :-

Area of each tile exc 0.11 Sqm but not exc 0.18 Sqm.

M&L for coloured, digital glazed ceramic tiles size 350x250x7-8mm or 450x300x 7-8mm thick as in dado/ skirting etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, laid with and including over 10mm thick rendering in CM (1:3) all as specified and directed.

Taking down cement plaster on brick or stone wall surfaces including glazed tiles wherever exists including raking out joints, hacking for key and scrubbing down with water and removing unseviceable materials out side MoD land complete all as specified and as directed.

M&L for 15mm thick plastering on brick work or concrete surfaces in CM (1:6) finished even and smooth without using extera cement complete all as specified and directed.

M&L for 15mm thick plastering on fair faces of brick wall in two layers, Ist layer 10mm thick in CM (1:6), and IInd layer 5mm thick in CM (1:4), surface finished even and fair mixed with @ 200ml per bag WPC (liquid type) complete all as specified and directed. Note :- WPC (Liquid type) shall be measured and paid separately as supply only.

Supply only WPC integral water proofing compound (Liquid type) complete all as specified and directed.

M&L for preparation of newly plastered surfaces on wall and applying two coats of oil emulsion distemper over alkali resistance for primming to distemper for smooth finish of wall complete all as specified and directed.

M&L preparation of new or plastered or unplastered and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

Taking down chowkhats or frames with shutters ( without taking off shutters from the frames) of following size complete all as specified and directed:-

Area not exc 1.5 sqm each

Area exc 1.5 sqm but not exc 4 sqm each

S&F PVC door frame (Chowkhat) of size 50mm x 47mm is made out of 5mm thick sheet properly jointed with slovent cement adhesive as per the sectional view. A mild steel square tube of size 19mm of 19 gauge is inserted inside to give extra structual strength. The door frame can be made with/without rubber gasket as required. If rubber gasket is not required then one strip of 5mm thickness can be eliminated and final size of chowkhat will be 50mm x 42mm. PVC door frame sections are cut in 450 and joined to each other perfectly at 900. 'L' shape brackets made out of MS square tube are inserted inside the chowkhat corners. These brackets are finally fixed using the steel screws from both the sides complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top, bottom and side rails, MS frame shall be covered with heat molded plain colour PVC “C” channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail & bottom rail on either side and as gap insert for top rail and bottom rail panelling of plain colour PVC sheet to be fixed in the MS frame welded /sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement and fixing in the frame at site complete all as specified and directed.

S&F factory made steel ventilators with top hung shutter including box type hinges with steel handle and Z-section handle and steel peg stay complete with glazing bars, dovetailed or welded including a shop coat of red oxide zinc chrome primer complete all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ ceosetory windows and other frames/ chowkhat of following size comprising of virgin PVC polymer having K-value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) and 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and direction. Note: (i) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable and variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. (ii) M.S. hold fast/ lugs or SS dash fasteners shall be measured and paid for separately.

65mm x 100mm size

M&L for 30mm thick factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter comprising of virgin polymer of K-value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk stainless steel screws complete all as specified and directed. Note: stainless steel butt hinges and necessary stainless steel screws shall be paid separately.

M&L for factory made 30 mm thick 100% solid WPC window glazed shutter and Gauzed (wire mesh) shutter 95 mm x35mm thick. Made from WPC material with density not less than 800 kg/cum. All four corner are fusion welded & screwed with 8 x 50mm self-screws for additional strength. After joining all 4 corner clear space to be paneled with 5mm thick glass / S S mosquito mesh after glazing of inside of shutter 10 x 12mm pvc “L” shape bead to be nailed or sticked with shutter. Provided 2 Nos SS hinges of 100 mm, 1 Nos aluminium handle of 125 mm , 2 Nosaluminium tower bolt of 125mm and 01 peg stay for each shutter (Glazed and Gauzed) incl factory made 100 % solid WPC window frame 125 mm x 65 mm double rebated frame & mullion 125 x 80mm. made from WPC (Single extruded process) material comparising of virgin PVC polymer of K value 57-60 (suspension grade), calcium carbonate and natural fibers (Wood powder/ rice husk/wheat husk) and nontoxic additives fabricated with meter joints after applying PVC solvent cement & screwed with fully body treated star headed screws having minimum frame desity not less than 800 kg /cum, having good screw holding capacity (screw withdrawal strength of (min 990N). Minimum compressive strength of 58 N/mm2. Modulus of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite / borer proof, water / mosquito proof & fire retardant & fixed in position with fasteners / hold fast of required size. Window shall be provided with MS Grill/Guard Bars made of 10mm MS Sq Bar welded to 6 x 12mm MS Flat including painting with countersunk holes at both vertical ends. Gap between the bars should not be more than 125mm. All as per specification drawing as directed by Engr-in-charge. Note - (i) Glazed and Gauzed shutter both are deemed in this quoted rate (ii) Glass pane, wire mesh and grill are deemed in this quoted rate

S&F 4 mm thick figured glass, pin headed type and glazing with oil putty /wooden beads in square exc 0.5 sqm in each pane complete all as specified and as directed.

Supply only MS butt hinge, medium weight, cold rolled and fixed of following size complete all as specified and directed:-

100 mm long

S&F extruded aluminium alloy handles, fabricated type, anodised (ISI marked) of following size complete all as directed and specified:-

150 mm long

S&F anodised aluminium barrel tower bolts (ISI marked) of extruded section of following size complete all as directed and specified:-

200 mm long

S&F anodised aluminium sliding door bolt (ISI marked) with hasp, staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections of following size complete all as specified and directed:-

300mm long

Taking up or down steel water tubing (GI Pipe) and connections of following bore complete all as specified and as directed :-

15mm bore

20mm bore

S&F galvanised steel water tubing (GI pipe), medium grade with all fittings (ISI Marked) and fixed to wall, floor and ceiling or laid in trenches of following bore complete all as specified and as directed :-

15mm bore

20mm bore

S&F in repair 15 mm bore gun metal globe or gate valves, ISI marked, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed

S&F in repair 1000 Ltrs Capacity rotational moulded polyethylene water storage tank, double layer construction, ISI mark (cylindrical vertical with closed top) hoisted and fixed in position with and including 20 mm dia GI pipe medium grade washout pipe 450 mm long with plug and 20 mm dia GI pipe medium grade overflow pipe 600 mm long with fittings, complete all as specified and as directed.

S&F in repair 20mm bore ( minimum weight 210gms) ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipes or brass ferrule and fixed complete all as specified and as directed

S&F 32 mm bore, 600mm long PVC flexible waste pipe with socket fixed with sink/WHB waste coupling complete all as specified and as directed

S&F in repair soap dish recessed type (stainless steel) fixed with CP screws and wood cleats with wall complete all as specified and directed.

S&F in repair vitreous china urinal half stall type urinal complete including providing and fixing plugs bedding urinal against wall in CM 1:2 securing urinal to plugs with & including 60 mm brass screws pointing around urinal back in cement fixing automatic flushing cistern with brackets flush pipe grating and union for discharge pipe complete all as specified and directed.

S&F in repair urinal spreader of PTMT any colour for fixing with 15mm dia pipe (Min wt 60 gms) complete all as specified and directed.

S&F in repair PVC valveless, symphonic action type low level flushing cistern white with inlet ball valve, float and handle including brackets, 10 ltr capacity complete with flush pipe(Long bend) 32mm dia complete all as specified & directed.

S&F in repair vitreous china wash hand basin, white, flat back, size 550mm x 400mm excluding taps, chain and plug and porcelain stopper but including cutting for and pinning in ends of and including brackets, waste pipe & CP brass waste coupling of 32mm dia complete all as specified and directed. Note : Rate quoted under this item deemed included fixing of taps, plug and chain and connecting up to supply pipes, wastes or traps etc.

S&F in repair 450mm long PVC connection 15 mm size with PTMT nut complete all as specified and directed.

S&F in repairs 15mm bore Stop valves (angular stop cock), cast copper alloy, fancy type, chromium plated with long shank and cup screwed down high pressure with crutch or butterfly handle or concealed screwed both ends for iron pipe or for unions complete all as specified and directed. Note for all CP item :- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site.

S&F in repairs 15 mm bore pillar taps, cast copper alloy, with capstan heads, chromium plated , Fancy type screwed down for pipe,high pressure , with or without lettered ' 'HOT' or 'COLD' with long screwed shanks and fly-nuts , screwed for iron pipe complete all as specified and directed.

S&F in repair 15mm bore stop angle valve, cast copper alloy, fancy type chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe complete all as specified and directed. Note:- Chromium plated fitting shall be brought in store yard first as approved by GE/AGE(I) and will be issued subsequently for fixing at site

S&F in repair chromium plated health faucet, telephonic type with CP flexible arms and hooks of approved make suitable to fix to 15mm bore CP angle valve complete all as specified and directed.

S&F in repair 5mm thick bevelled edge best quality looking mirror of size 600x450 mm with 30 mm PVC beading all around the glass, mounted over 3mm thick PVC sheet or 6mm thick AC bldg board, complete all as specified and directed.

S&F in repair chromium plated brass tubular towel rail, 20mm dia, D type, 60 cm long between flanges complete all as specified and directed.

S&F in repair vitreous china wash down water closet pan (pedestal pattern), white/ivory, with and including plastic seat and cover, white, closed pattern with flat bottom and mild steel chromium plated or aluminised hinging device, (excluding fixing bolts, flushing cistern and flush pipe) including connection to drain (or outgoing pipe) and to flushing pipe, anti -syphonage pipe, etc., complete all as specified and directed.

S&F in repair vitreous china squatting pan of “Orissa” pattern of size 580 mmx 440mm white with integral foot rest (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, anti syphonage pipe etc and making good to floor complete all as specified and as directed.

S&F in repair 15 mm bore bib taps, cast copper alloy with crutch or butterfly handle, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F PVC (SWR) floor trap, out let dia 75mm, plain with grating including jointing with solvent cement complete all as specified and as directed.

Demolition and breaking up drain pipes (PVC/ SGSW/ AC/ RCC pipe) of following bore of pipe, set in cement mortar complete all as specified and as directed:-

100mm bore

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints and laid in trenches or in floor of following size complete all as specified and as directed :-

110 mm bore

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints and fixed to wall of following size complete all as specified and as directed :-

110 mm bore

75 mm bore

M&L concrete bed to pipes in PCC (1:3:6) type C2 (using 40mm graded stone aggregate) including packing under and haunching against the sides of pipes after they are laid on slope and tested for following bore sewer pipe line complete all as specified and directed :-

110mm bore

S&F PVC (SWR) bends any radius including necessary cutting in brick wall and making good to match with existing surface of following size complete all as specified and as directed :-

110 mm bore

75 mm bore

S&F PVC (SWR)branch piece, single (single Y) equal or unequal of following size complete all as specified and as directed :-

110 mm bore

S&F PVC (SWR) junction single, (single T) with access door equal or unequal of following size complete all as specified and as directed :-

110 mm bore

S&F 75 mm bore PVC (SWR) vent cowl complete all as specified and as directed

M&L for PCC (1:2:4) type B-1, using 20mm graded stone aggregates, as in kerb/ benching/ coping, bed plates, for fixing of hold fast, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and directed.

M&L for cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required for 110 mm dia pipe complete all as specified and directed.

M&L preparation of old plastered or unplastered surfeces of wall and applying two coat of distemper emulsion white or tinted over and incl of one coat of alkali resistance priming paint and 1mm thick wall care putty on wall surface.Complete all as specified and directed

M&L preparation of old or plastered or unplastered surfeces of wall and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces Complete all as specified and directed

M&L for rubber moulded coloured glossy finish chequered cement concrete tiles, ISI Marked, set and jointed and pointed in neat cement slurry with grey cement and pigment in floors over and including 20 mm thick screed bed in cement mortar (1:6) for following size of tile complete all as specified and as directed:-

30cm x 30cm x 25mm thick

Excavating in trenches n'exc 1.5 m width and n'exc 1.5 m in depth for foundation etc / for laying of cable/ pipe etc n'exc 10 sqm on plan and n'exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

Excavating in trenches n'exc 1.5 m width and n'exc 1.5 m in depth for foundation etc / for laying of cable/ pipe etc n'exc 10 sqm on plan and n'exc 1.5 m in depth and getting out in any type soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. complete all as specified and directed.

Removal of surplus soil to a distance n'exc. 100 Mtr and depositing where directed at a level not exc 1.5m above the starting point complete all as specified and directed.

Dismantling and taking down U/S copper / aluminium point wiring (light, fan, socket, power) complete fitting such as switches, ceiling roses, pendants, lamp holder, light fitting etc including CI/Pressed steel terminals, switch box, and making good the disturbed surface of wall/floor etc, to match with the existing surfaces of wall/floor complete all as specified and directed. Note :- If the contractor fail to make good the disturbed surface of wall/floor etc and do not match with the existing surface of wall/floor to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding.

Dismantling and taking down carefully existing DB’s any type and making good the disturbed surfaces of wall/floor to match with the existing wall/floor etc. complete all as specified Note:- Note:- i) Cost of cutting chases of suitable girth where required on brick /concrete surface and making good disturbed surface shall be deemed to be included in quoted rates( ii) If the contractor fail to make good the disturbed surface of wall/floor etc and do not match with the existing surface of wall/floor to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding. If the contractor fail to make good the disturbed surface of wall/floor etc and do not match with the existing surface of wall/floor to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding.

Dismantling and taking down u/s sub-main wiring/service wire of any size including wooden batten / PVC Conduit etc and making good the disturbed surfaces of wall/floor to match with the existing wall/floor etc excluding conduit when in wiring in existing conduit complete all as specified & as directed. Note :- If the contractor fail to make good the disturbed surface of wall/floor etc and do not match with the existing surface of wall/floor to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding.

Material & Labour for Point Wiring for one light Point/one fan point/ one call bell point, controlled by one switch with 1100 volts grade single core conforming to (IS:694 /1990) PVC insulated unsheathed 1.5 sqmm multi stranded copper conductor cable (FRLSH) with contineous earth wire of 1.5 Sqmm stranded copper conductor cable (FRLSH) PVC insulated unsheathed , drawn in and including concealed PVC conduit ,duly concealed to wall/floor or above false ceiling with fittings(ISI marked) not less than 20 mm dia (Color coding of wires shall be Phase, neutral and earth wire all as specified ) sunk Metal flush box with and incl decorative polycarbonate frame for housing Modular Switches, sockets , fan regulators etc including white cover cover plate complete all as specified and directed. Note:- i) Cost of cutting chases of suitable girth where required on brick /concrete surface and making good disturbed surface shall be deemed to be included in quoted rates ii) If the contractor fail to make good the disturbed surface of wall/floor etc and do not match with the existing surface of wall/floor to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding.

One 3pin/5pin 5/6 Amps socket out let on same board with other switches , with cables 1.5 sq mm size , complete all as specified and directed.

One 3pin/5pin 5/6 Amps socket out let on independent board with other switches, with cables 1.5 sq mm size, complete all as specified and directed .

All as per item No 76 above but with 2.5 Sqmm PVC insulated FRLSH cable for 15 Amps power point complete all as specified and directed.

S & F Switch Modular single pole, one way 6 Amps, 1 module 240 Volts AC all as specified and directed.

Supply and fixing switch modular , one-way 16Amps, 1 module 240 Volts AC all as specified and directed by Engr- in-charge.

Supply and fixing modular socket, 6A -2/3 pin combined 2 module ISI marked 230 volts, 50 Hz all as specified and directed.

Supply and fixing modular socket, 6A/16A -2/3 pin combined 2 module 230 volts 50 hz all as specified and directed

Supply and fixing ceiling rose surface bakelite 65x25mm dia having three terminals ISI marked all as specified

Supply and fixing batton/angle holder insulated body with back plate, suitable for batten fittings all as specified & directed.

Supply and fixing sheet metal enclosure double door type for MCBs DB SPN(Single pole and neutral) 240V AC 08 way with 200 Amps rated bus bar all as specified and directed .

Supply and fixing sheet metal enclosure double door type for MCBs DB SPN(Single pole and neutral) 240V AC 04 way with 200 Amps rated bus bar all as specified and directed .

Supply and fixing MCB SPN 32-40 Amp 240 V AC 10 KA C series repturing capacity complete all as specified.

Supply and fixing MCB SP 5-10 Amp 240 V AC 10 KA B series repturing capacity complete all as specified.

Supply and fixing in repair sub main wiring two single core 4 sq mm PVC insulated unsheathed multi stranded copper conductor cable ( FRLSH ) 1100Volts grade drawn in & including rigid PVC conduit 20mm dia or more medium grade surface/ concealed in wall as per existing along with 4.00 Sq mm PVC insulated unsheathed copper conductor cable (FRLSH ) as earth wire and wire connected with main earth dolly including cutting chasing and making good disturbed portion all as specified and as directed Note:- Two runs of multi stranded copper conductor cable and one run of earth wire including PVC conduit will be measured as a one length.

Supply and fixing LED lights fitting 1X20 watt ,4 ft with extruded aluminium housing heat sink, environmental friendly energy efficient translucent diffuser with LED light source,2400 Lumens( minimum) coefficient colour temp 6000°K to 6500 °K, surge protection range ≥ 2.5KV, voltage protection range-120-300VAC,2 years warranty ,system efficacy not less than140Lm/Watt for the fitting, power factor >.95,total harmonic distortion< 20% color rendering index>80, fixed on site with all accessories including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose all as specified & directed

Supply and fixing energy efficient LED lights fitting, 10 watt , 230 Volt, of 600 mm length,CCT 6000ºK to 6500° K , decorative ultra slim linear LED lighting fixture with extruded aluminium housing heat sink, environmental friendly, energy efficient LED light source more than1200 lumens , wall mounted mirror batten, integrated electronic driver, system efficacy not less than 140 lumens /watt CCT 6000 to 6500°K , surge protection range ≥ 2.5 KV , voltage protection range 120-300 volt AC, power factor > 0.95 total harmonic distortion < 20%, colour rendering index > 80, fixed on site with all accessories including 2 years warranty connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified & as directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300 mm sweep with, blades, and frame and louvers all as specified and directed.

Supply and fixing in repair LED building security light 1X20 W housing made out of pressure die-cast aluminium alloy with toughened glass, IP-66 protection, working on 240 Volts , 50 HZ, consisting of reflective lens wired with appropriate driver PF>0.98 having over voltage protection up to 440 volts, Surge protection level ≥ 10 KV, thermal short circuit protection THD < 10% made up of long life LED chips (SMD) in modular with Ra>70, and LED lumen efficiency >140 lumen per watt, beam angle along the drive way, 120 degree, beam angle across the drive way, 80 degree luminior efficiency > 130 Lumens/watt, power LED should be of more than 01 watt CCT should be between 5700° K- 6500° K including fixed on wall with 02 Nos MS clamp made out of 40X6 mm FI and bracket made out of 32 mm dia light grade GI pipe not less than 0.90 mtr long bend to shape complete all as Specified and directed including connecting with 1.5 sq mm, 3 core, PVC insulated Copper conductor cable 1100 Volts grade from terminal box to light fittings complete all as specified and as directed by Engr-in-Charge (i) the firm has to give warranty for street light fittings including driver minimum for 03 years for any defects developed during the period. (ii) The contractor shall submit the third party LM 79 report from any NABL approved laboratory. (iii) The fitting should have BIS, CRSno

Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground. ( earth pit not less than 2.25 mtr depth below ground level at any type of strata ) with top edge of the earth plate not less than 1.5mtr below normal ground level connected by 4 mm GI wire as earth lead by means of brass nuts and bolt,thimbles check nuts, washers including concrete chamber of PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish, internal surface of concrete chamber shall be given internal dia 300mm x300mm, 15mm thick plaster in CM 1:4 funnel with wire mesh, RCC pit cover of 320x320x80mm size (1:2:4) Type B1 using 20mm graded stone aggregate rainforced with XPM and charcoal, dust and common salt all as shown in electrical plate No 3 of MES SSR Part-1(2009) and specified including and provision of GI wire upto 7.5 mtrs long with 15 mm dia light grade Gi pipe protection and watering pipe of GI 20 mm bore, medium grade, including all exavation and earth work and connecting the earthing strip to panel, including testing on completion complete all as specified and directed by Engr-in-charge. Note:- (i) RCC pit cover shall be precast of RCC(1:2:4) type B1, 80mm thick rainforced with XPM weighting not less than 4kg/sqm in lieu of CI cover. (ii) Cost of additional GI wire more than 7.5 mtrs will be measured and paid seperately under relevant items.

Supplying, laying, commisioning and testing of 1.1 KV grade XLPE insulated, PVC sheathed, steel armoured, aluminum stranded conductor LT UG cable (Conforming to IS 7098), ISI marked, in trenches / ducts / through GI pipes under roads of following size complete all as specified and directed:- Note:- 1. The earth work, GI pipe shall be measured and paid sepretely. 2. Cable may fixing/ passing through pipe laid in trenches or fixed to pole/ wall or fixed to LT panel etc.

6.00 Sqmm, 2 core.

M&L for sand cushioning with dry and clean fine river sand for underground cable 8 cm before laying cable and 15 cm after laying and punned to 18 cm after laying of cable complete all as specified and directed. Note:- Punned thickness shall be considered for payment purpose.

Supply and laying cable protection bricks, common burnt clay sub class 'B' designation 75 for protection of UG cable laid in trenches with axis of the bricks perpendicular to the axis of the cable complete all as specified and directed.

RAMAN CONSTRUCTION CO. (BID ID -3373750)

AMARJEET SINGH AND CO. (BID ID -3373192)

Malik Associates (BID ID -3369281)

SAVV BUILDERS (BID ID -3381691)

TARUN ENGINEERING WORKS (BID ID -3373505)

M/s RP AGRAWAL (BID ID -3373722)