Addn/ Altn cum spl repair to Physics Lab, Chemistry Lab, Biology Lab and Junior science Lab at KV Upper camp , spl repair to roof sheet of Bldg No T-8 OR living (OTM) of 127 Inf Bn and Constr of sentry post at RP Gate No 1 of 5 Grenadiers under GE De

Amount

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified

Dismantling of timber scantlings 40 Sqcm and over in section in any position and in any situation. (unframed work) complete all as specified.

M&L brick work with fly ash brick straight or curved on plan exc. 6 m mean radius built in cement mortar 1:6 including all quoins, arches, pillars etc complete all as specified

M&L brick work with old bricks straight or curved on plan exc. 6 m mean radius built in cement mortar 1:6 including all quoins, arches, pillars etc, but except bricks complete all as specified (Note- old bricks shall be re-used obtained from demolition).

M&L brick work with fly ash brick straight or curved on plan to any radius built in cement mortar 1:4 as in half brick thick wall complete all as specified.

Taking down cement or cement lime plaster/ tile work on brick or stone walls etc. including racking out joints, hacking for key and scrubbing down with water etc. complete all as specified

M&L 5 mm thick plastering on ceiling in CM (1:4) finished even and smooth without using extra cement complete all as specified and directed.

M & L 15 mm thick rendering on fair/ unfair faces of brick work or concrete surface in cement mortar 1:6, surface finished even and fair without using extra cement complete all as specified

M & L 15 mm thick rendering in cement mortar 1:4 on fair/ unfair faces of brick work or concrete surfaces, surface finished even and fair with water proofing compound without using extra cement complete all as specified & directed by Engineer-in Charge. Note: Water proofing compound will be measured & paid separately under respective item of the schedule.

Supply only liquid water proofing compound as per manufacturer instructions.

M&L for complete removal of existing treatment of old decorated surfaces of walls by washing, rubbing down, electric sand paper grinder, and stopping of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces finally rubbed and smooth with sand paper all as directed by Engr-in-charge.

M&L for preparation of old decorated surfaces of walls and applying interior grade wall care putty 1.0 to 1.50 mm thick to make the surface smooth as specified in SSR Part-I and as directed by Engr-in-Charge. Make : Berger/ Asian/ JK/ Birla.

M&L for two coats of oil bound distemper over a coat of alkali resistant primer on newly plastered/ old decorated/ putty surfaces of wall including preparation complete all as specified and directed.

M&L, preparation of old plastered/ un plastered surfaces of walls and providing two coats of OBD as in walls completed all as specified and directed

M&L for two coats of plastic emulsion paint over a coat of alkali resistant primer on newly plastered/ unplastered/ putty surfaces of walls including preparation complete all as specified.

M&L for preparation of old decorated surfaces of walls and applying two coats of weather coat (Apex Ultima) over a coat of alkali resistant primer complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of weather coat (Apex Ultima) over a coat of alkali resistant primer complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying three coats of white wash on walls etc complete all as specified and directed.

M&L for preparing old decorated surfaces of ceiling and applying two coats of white wash complete all as specified and directed.

M&L for preparing newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M & L for two coats of cement based paint over one coat of cement primer on newly plastered surfaces of wall complete all as specified.

Demolition of PCC/ terrazo floor in ground floor and paving n.exc 15 cm below or above ground level including tiles stone flooring etc complete all as specified.

M & L 25 mm thick PCC 1:2:4 type B-0 using 12.50 mm graded aggregate as in levelling course to floors, etc finished even and fair without using extra cement complete all as specified.

M&L for cement concrete ( 1:3:6 ) type C1 (using 20 mm graded stone aggregate) as in surface channels and drains and benching including finishing the top of benching even and smooth using extra cement and necessary form work complete. Note : Forming fair finished channel for drain using extra cement will be measured and paid for separately.

M&L for 75mm thick PCC 1:3:6 type C-1 using 20 mm graded stone agg as insub base for lay floor finishes complete all as specified and as directed.

M&L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including form, moulds, mitred, stopped ends etc complete all as specified.

M& L PCC 1:2:4 type B-1 (using 20 mm graded stone aggregates) as in coping,benching,anchorage blocks, lintels upto 1.5m clear span,cills, steps, sesmic & other similar bands, plinth course, lacing course, parapets & ralling upto 60 cm in height, coping, kneelers, apex stones, bed plates, kerbs not provided for water trought & the like including weathering, slightly rounded or chemfered angels & throating and formwork as directed and specified.

Surface excavation in any type of soil n. Exc. 30 cm deep and averaging 15 cm deep and getting out complete all as specified.

Excavation in trenches in any type of soil, n. exc. 1.5m wide and n. exc. 1.5m deep and getting out complete all as specified.

Returning filling in, including spreading, leveling, watering and well ramming in layers n. exc 25 cm thick in any type of soil complete all as specified.

Removal of surplus excavated soil to a distance n. exc. 50 m and depositing where directed at a level n. exc. 1.5 m above starting point complete all as specified.

M & L 100 mm thick cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in floor finishes, pavings, etc complete all as specified and directed.

M & L PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation filling, mass concrete, sub base or leveling course of floor etc. complete all as specified.

M & L RCC 1:2:4 type B1 using 20 mm graded stone aggregate as in column footing including raft footings, foundation, plinth beam, bases of columns etc. complete all as specified and as directed.

M & L RCC 1:2:4 type B1 using 20 mm graded stone aggregate as in columns, pillars, posts and struts etc. complete all as specified and as directed.

M & L RCC1:2:4 type B1 using 20 mm graded stone aggregate as in beam, cantilevers, lintel chajjas etc. complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) rubbish off the premices complete all as specified.

Dismantling wall and ceiling boards (fiber, pulp, insulation etc) or insulation boards/ slabs/ blankets any thickness incl cover fillets. Complete all as specified and directed.

M&L double charged vitrified ceramic coloured tiles 10 mm thick (square/rectangular) polished,area of each tiles not exceeding 0.36 sqm, in floor etc. set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

All as per item No 39 here-in- above but in skirting over and including 10 mm thick rendering in CM 1:4 complete all as specified.

M&L non-skid / mat finish designed coloured joint free ceramic tiles of size not less than 400 mm x 400 mm x6- 7 mm thick in floor, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed in cement mortar 1:6 complete all as specified.

All as per item No 41 here-in- above but as in skirting over and including 10 mm thick rendering in cement mortar 1:4, complete all as specified.

M&L for pre-polished pavement coloured chequred tiles glossy finish of size not less than 300 x 300 x 20-22mm thick with anti skid properties laid over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

M&L for Machine cut kota stone slab flooring 18-20 mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing rounding edges if required and polishing over and including 20 mm thick screed bed in cement mortar 1:6 complete all as specified.

M&L for Machine cut kota stone slab as in skirting 15-18 thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 10 mm thick rendering in cement mortar 1:6 complete all as specified.

M &L Glazed Ceramic tiles coloured, of size 450mm x 300mm 6 to 7mm thick approved 1st quality as in vertical surfaces such as skirting/ dados etc, set and jointed in neat cement slurry and pointed with white/ coloured cement to match the colour of tiles over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

Demolition of stone slab and tiles and laid bedded in any mortar of any description in floors, apron, etc. complete all as specified.

M&L for 16-18 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

M & L 75mm th PCC (1:3:6) type C-2 as in plinth protection, finished even and fair without using extra cement.The plinth protection shall be laid in alternate bays nexe 2sqm, 10mm joints shall be provided joints shall be filled with bitumen mastic, bitumen mastic comprises of 1 part of hot bitumen 85/25 grade and 3 parts sand all by weight complete all as specified.

Taking up or down steel tubing and connections including cleaning for refixing with all fittings for 15 mm bore GI tubing complete all as specified.

Taking up or down steel tubing and connections including cleaning for refixing with all fittings for 20 mm bore GI tubing complete all as specified.

M&L cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves lintels etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good cutting not exc 10cm girth.

Supply, fixing, laying & testing 15 mm dia (Nominal bore) galvanised iron water tubing 'medium grade' with and including all GI fittings such as unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

Supply, fixing, laying & testing 20 mm dia (Nominal bore) galvanised iron water tubing 'medium grade' with and including all GI fittings such as unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S&F PVC connection 15mm size with PTMT nuts, of 450 mm length complete all as specified.

S&F CP bib tap long body fancy type cast copper alloy 15 mm bore screwed down screwed for iron pipe or for brass ferrule complete all as specified.

S&F in repairs CP brass fancy type Angle cock 15mm dia ISI mark complete all as specified.

Demolition of reinforced cement concrete, of any description and in any position and debris off the premices complete all as directed.

M&L for RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in slabs supported on walls, beams and colums, in floors, roofs, landing balconies, canopies, deck slabs, chajja and in shelves and the like, complete all as specified and directed.

S&F mild steeel work as in main and cross beam, hip and jack rafters, purlins etc. fixed with angle cleat or other connecting plate complete confirming to Fe - 410-O or Fe - 310-O long complete all as specified and directed.

Use and waste for form work for RCC Slab such as roof slab, chajja, floor slab, slab supported on walls etc. for fair finished surfaces n.exc 200 mm thick complete all as specified.

Use and waste for form work to edges of concrete flats, treads, break in floor & roofs n.exec 20 cm wide horizontal or sloping and smilar works complete all as specified.

Use and waste form work to sides of concrete foundation, footing, bases of columns, plinth beam, side and soffits of plinth beam and similar works in vertical or to batter of fair finished surfaces complete all as specified and as directed.

Use and waste form work to sides of columns, pillars etc. of fair finished surfaces complete all as specified and as directed.

Use and waste form work to sides and soffits of floor or roof beams, lintel, cantilevers, shelves etc. including support of fair finished surfaces complete all as specified and as directed.

S & F mild steel work as in holdfast, hooks for hanging fans and similar small articles conforming to Fe- 290 Gde-E-165 including necessary welding or fixing nuts and bolts complete all as specified.

S&F mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

M&L for MS TMT bars 6 to 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified and directed.

M&L MS TMT bars 5mm dia and over up to and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required,including binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

Taking down chowkat with shutter of any description exc 1.5 sq.m but n.exc 4 Sqm each without taking off shutter from frame complete all as specified.

Taking down chowkat with shutter of any description n.exc 1.5 sqm each without taking off shutter from frame complete all as specified.

Taking down shutter only of any description exc 1.0 sq.m but n.exc 2.00 sqm each and refixing in the same opening aftrer necessary easing and repair complete all as specified.

S&F in factory made steel window made out of steel square/rectangular hollow section including MS hinges, steel handle and steel peg stay, complete without glazing bars, dovetailed or welded including taking down old window complete all as specified and directed.

S&F factory made steel window made out of steel square/rectangular hollow section including MS hinges, steel handle and steel peg stay, complete with glazing bars, dovetailed or welded including taking down old window complete all as specified and directed.

S&F of power coated ventilator fixed type and frame made with aluminium section with and including partly glass and partly stainless steel wire mesh and including aluminium grill of aperture not more than 40 sqcm (as specified below), aluminium sections shall be of size as given below including taking down old window/ventilator etc complete all as specified and directed by Engineer in Charge. Frame : 44.5 x 44.5 mm x 1.98 mm thick including 5mm thick frosted in glass fixed with rubber gasket with aluminium beading and stainless steel wire mesh of 0.63 mm nominal dia wire and average width of aperture 1.40 mm complete including taking down old window/ventilator etc complete all as specified and directed by Engineer in Charge. Note :- (i) Making good of wall surface with matching to existing surface complete all as specified and directed by Engineer in Charge. (ii) Cost of glass and gauge shall be included in the quoted rate including taking down old complete all as specified and directed.

Dismantling of block board as in kitchen cabinets and the like and making good disturbed surfaces to match with the existing complete all as specified and directed

S&F 15 mm thick PVC sheet of both side plain white colour fixed with screws, solvent cement/ adhesive to make kitchen cabinet sides top and bottom and shelves inside the cabinets complete as per specifications and as directed by the Engineer-in-charge.

S&F 18 mm thick PVC sheet of one side plain and one side prelaminated colour to make kitchen cabinet Partition Shutter/ drawer Front, cup board shutters complete as per specifications and as directed by the engineer - in - charge.

S&F 4.8 mm thick sheet glass ordinary quality in squares n exc 0.50 Sqm each as in cup board shutters fixed with PVC beading complete as per specifications and as directed by the Engineer-in-Charge.

S & F SS Cupboard Cabinet Glass 2 Wheels Sliding Door Rollers with ball bearing arrangement for sliding movement of glass with complete assembly exc 0.25 but n exc 0.60 m in length complete all as specified and directed.

S & F Continuous (Piano) hinges, mild steel, bright finished or electro galvanized, width of flaps (When open) 30 mm complete all as specified.

S&F 150mm SS Hasp and staples safety type, gde-204 including bolt to hings plate and fixed with screwed complete all as specified.

S&F 150 mm long bright finish stainless steel handles gde-204 complete all as specified.

S&F magnet catcher for cub board with brass body and striking plate including letting in and fixed complete all as specified and directed.

S&F 100 mm size MS butt hinges medium weight cold rolled fixed/ welded to frame complete all as directed.

S&F mild steel 300mm long, ordinary rat rail rod pattern spring including roller and roller plate (Helical door spring) for door shutter complete all as specified.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks or galvanized wire staple complete all as specified and directed.

S&F in repair galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks or galvanized wire staple complete all as specified and directed.

M&L for two coats of synthetic enamel paint over a coat of red oxide or zinc chromate primer including preparation of new steel or iron surfaces over 10 cm width or girth, complete all as specified.

Dismantling Mild steel work of any description and in any position not otherwise provided for complete all as specified.

Hacking out old broken glass (any thickness) size, quality or description from wooden or metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified.

M & L sheet glass ordinary quality 3mm thick and glazing with oil putty in squares n.exc. 0.5 sqm in each pane complete all as specified

S&F in repair 25 mm dia stainless steel drapery rod including brackets and decorative finials at both end complete all as speccified and directed.

M & L PCC 1:5:10 type E-2 using 40mm graded stone aggregate as in foundation filling, mass concrete, sunken filling sub base or leveling course of floor etc complete all as specified.

S&F in repair PVC (SWR) pipe 110 mm bore, single socketed, in any length with rubber ring joints and jointed with approved adhesive and fixed in walls complete all as specified and directed.

S&F in repair PVC (SWR) pipe 75 mm bore, single socketed, in any length with rubber ring joints and jointed with approved adhesive and fixed to wall complete all as specified and directed.

S&F in repair PVC (SWR) pipe 75 mm bore, single socketed, in any length with rubber ring joints and jointed with approved adhesive and laid in trenches or in floors complete all as specified and directed.

S&F PVC (SWR) bend 110 mm dia, any radius with oval access door complete all as required and as directed.

S&F PVC (SWR) bend 75 mm dia, any radius with oval access door complete all as required and as directed.

S&F PVC floor trap of 75mm bore, with grating including jointing to waste pipe with solvent fixed in cement concrete type B1 (1:2:4) complete all as specified.

S&F waste fitting brass chromium plated for 32mm bore with long screwed shanks and fly nuts including 32mm PVC waste pipe for WHB complete all as specified.

S&F in repairs Vitreous China wash basin, flat back, size 600 x 480mm white, excluding taps, waste pipe, chain and plug and porcelain stopper but including brackets complete all as specified.

S & F in repair vitreous china wash hand basin white, oval type counter sunk of size 550mmx400mm fixed on and including 32mm dia brass waste coupling and 32 mm dia PVC waste pipe, waste fitting etc. complete all as specified. Make : Jaquar (FLS-WHT-5701) or equivalent in Hindware/Parryware.

Supply and fixed pillar taps 15mm bore cast copper alloy with swan neck, chromium plated, screwed down high pressure with or without lettered hot or cold with long screwed shanks and fly nuts, screwed to iron pipe & fixed.

S&F in repairs 20mm dia brass chromium plated tubular towel rails, D type, 60cm long between flanges, complete all as specified.

S&F in repairs Gun metal gate valve with iron wheel head screwed both ends for iron pipe of 20 mm bore complete all as specified.

S & F in repairs stainless steel kitchen sink without draining board made of stainless steel 1mm thick,coupling plug, washers and waste pipes including bedding in cement mortar on to dwarf wall or including fixing cantelever brackets and connecting union to pipe, overall size 495 mm X 420 mm, bowl size 410 mm X 330 mm X160 mm all as specified and directed.

M&L for precast reinforced cement concrete (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in landings, cover slabs ( for manholes etc.), shelves and similar articles with plain faces including necessary form work, set in cement mortar (1:4) complete all as specified and directed. (Note - Reinforcement shall be measured and paid for separately under respective item of BOQ).

S&F aluminum alloy powder coated door made out of hollow extruded aluminum section as mentioned below. Each door having 02 Nos Disc or D type handle, 02 Nos aluminum tower bolt 200 mm size, one brass mortice lock of six lever with key in duplicate regulated by double action hydraulic floor spring heavy duty (Make:- Sandhu/Ritz) shutter to be partly glaze with 5mm thick tined coloured glass in upper pannel and partly pannelled with 12mm thick both side laminated particle board in lower pannel fixed with glazing clip, rubber beading/gasket, anodised aluminum beading screw complete all as specified and directed at site. Chowkhat Frame:- 101.60 x 44.45 x 1.60 mm Shutter verticle style :- 85 x 44.45 x 1.56mm shutter middle Rail :- 83.50 x 44.45 x 1.54 mm Shutter Top Rail and bottom Rail :- 114.30 x 44.45 x 1.55mm incl taking down existing wooden door Make: (i) Anodised aluminum section : Jindal / Hindalko / Indalco. (ii) Particle board: Navipan / Puratuff / Kitlam (iii) Glass: Saint gobain / Modi guard / Tata

S&F powder coated Aluminium partition (Fixed) made out of aluminium powder coated section 83 x 44.45 x 2.00 mm including 5 mm thick glass/ACP Sheet complete with rubber packing/aluminum beading etc including dismantling of exixting structure complete all as specified and directed. Make: (i) Anodised aluminum section : Jindal / Hindalko / Indalco. (ii) Particle board: Navipan / Puratuff / Kitlam (iii) Glass: Saint gobain / Modi guard / Tata

S&F powder coated aluminium window double shutter with frame and shutter and glazing wire gauge, rubber gasket, aluminium glazing clips, aluminium peg stay, iron mongary etc including taking down existing wooden window complete all as specified and directed. aluminium sections shall be given below: - Frame;- 85x44.5x1.20 mm thick fixed with rawal plug Style;- 44.5x44.5x1.20 mm thick Glazing beading;- 0.70 mm thick Aluminium handle 'D' type ;- 100mm Aluminium tower bold 9.9 mm dia shoot 150 mm long Glass;- 5 mm thick frosted/ plain glass ( as specified) wire mesh Stainless steel of 0.063 mm nominal dia wire and average width of arperture 1.40 mm Aluminium stopper cleat, aluminium hinges 100 mm long powder coated

S&F in repair glazing (5.00 mm thick float glass) in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket and aluminium snap beading etc. complete all as direted by engineer-in-charge . (Note : - Cost of aluminium snap beading and EPDM rubber/ neoprene gasket if required shall be paid and measured seperately)

M & L for 02 mm thick SS sheet of grade 304, plain, in wall cladding, steel gates and similar work, cut to size, holes punched, including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or truning up, mitred angles etc as required & complete all as specified.

S&F mild steel, plain, black sheet 1 mm thick in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitered angles, etc. as required complete all as specified.

S&F 8 mm thick mild steel plate (plain or chequered channels, squares cut or notched (ordinary and counter sunk forming holes, without any attachment complete all as specified and directed

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws including dismantling of old asbestos sheet complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding/ ridge to wall, fixed with self tapping screws including dismantling of old asbestos sheet complete all as specified and as directed.

S&F in repair Pre-painted galvalume aluminium zinc coating GI based valley gutter of 1.0 mm thick sheet any colour having fixed with self tapping screws complete all as specified and as directed.

S&F in replacement 4 mm thick 'E' board in false ceiling including & fixing of frame work made of special section MS sheet glavanised with zine coating, cellular nitro painting & consisting of angle cleats of size 25 mm wide, 1.60 mm thick with flange fixing to the ceiling with dash fastener 12.5 mm x 40 mm long or with 4 mm dia GI wire or fixed with nails or bolts in GI channel 45x14x0.90 mmrunner at 600mm c/c including fixing of E board with ceiling section & perimeter of angle 25x25x0.50 mm thick complete all specified, and directed

Taking down existing light, fan, socket or power including fitings and re-fixing the same after completion of repair work and making good disturbed surfaces of walls, floors, etc complete all as specified and directed

S&F in repair 110 mm bore UPVC (SWR) pipe 4 Kgf/cm2single socketed in any length with rubber ring. Joints laid in trenches complete all as specified.

S&F in repair UPVC (SWR) bend, 110 mm bore complete all as specified.

M&L moorum/ red bajary filling in flloors or pavings, laid in layers n. exc. 15 cm thick, spread, levelled, and rammed including watering complete all as specified.

M & L for hardcore of broken bricks of gauge n. exc. 63 mm, deposited, spread and levelled in layers n. exc. 15 cm thick, watered and rammed to a true surface complete complete all as specified.

S&F mild steel Framed work such as grills, gratings , Iron Chowkhats etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work mild steel conforming to Fe 290. Gde-E-165 complete all as specified and directed.

M&L for Point wiring with1100 Volts, grade 1.5 Sqmm. (nominal area) ,PVC insulated but unsheathed multistranded copper conductor single core FRLS cable drawn through and including non metallic medium duty rigid PVC concealed conduit (medium duty) 20mm dia or higher size complete with all accessories such as socket, elbow, junction box, bell mouth, bend, reducer etc including pressed iron/steel suction box of thickness1.2mm for mounting of switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet as top cover, and 1.5 Sqmm. (nominal area) single core FRLS,PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor cable green colour as earth wire upto common earth and connected to earth dolly including cutting chases for conduits and sinking's for boxes and making good to walls,floors etc complete all as specified and directed by Engr.-in-charge of following. Note : The wiring to be done as per IE rule and maintain colour code accordingly.

One light point controlled by one way switch.

One fan point , controlled by one way switch through Regulaor

One three pin 5 Amp socket on same board with other switches

One three pin 5 Amp socket on independent board

All as per Item No 127 here-in- before but one three pin 15 Amps switch socket out let on the independent board with 2.5 sq mm PVC insulated FRLS copper conductor and 2.5 Sqmm FRLS copper conductor for continuous earthing complete all as specified.

S & F Switch piano flush type single pole one way 230 Volts 6 Amp complete all as directed.

S & F Socket outlet 3 pin , 230 Volts 5/6 Amps flush type multipurpose 5 pin complete all as specified.

S&F Socket outlet multipurpose having provision for 3 pin, 230 Volts 15/16 Amp and 3 pin, 5/6 Amp, piano flush type IS: 1239-1988 marked with valid CML No complete all as specified.

S&F Switch piano; flush type, single pole, one way, 230 Volts 15/16 Amps IS: 3854 marked with valid CML No. complete all as specified.

S&F Ceiling rose, Three terminal ISI marked surface bakelite suitable for batten fitting complete all as specified Make- HPL/Havells/Anchor

S&F Lamp holder polycarbonate insulated body, with back plate suitable for batton fitting. Make HPL/Havells/Anchor

S&F wall mounted LED tube light fitting 1x20 watts extruded aluminium polycarbonate covers PF 0.9 and above operating voltage 140V-270V colour temp 6500K & lumen input output 95 Lumen per watt and connected to ceiling rose with required length of two core flexible copper cable 23/0.0076 fixed on wall/roof complete all as specified and directed.

S&F Wall mounted fan 400mmsweep,230v ,single phase AC,1350 RPM,65 CMM,55 watt. Make : CG esteem model SKUcode 250542 equivalent in Havells/Usha/Bajaj

S&F energy saving ,surface mounted, LED 10 watt Bulk head luminaire with decorative oval diffuser comprrising of high brightness LEDs complete all as specified and directed by Engr-in-charge. Make : CG cat LBHP-10-CDL/Philips WT140W LED7S CW PSU S1 PC/Havells ENDURA RUGBYNEO N /Mepro cat no BCL 23 Plain

Supply and fixing Distribution board SPN 4 Way double door, for mounting MCBs isolator, ELCBs etc factory made, IS: 13032 marked with valid CM/L No fabricated out of CRCA sheet not less than 1.2 mm thick fitted with DIN channel, neutral and earthing link and bus bar. DBs shall be semi glossy finished with epoxy polyester based powder paint sprayed and baked at high temperature, painted in seven tank process. The DBs shall be of IP 43 protection.Note:- DB and MCCB/MCB shall be of same make Make:- Legrand/Hager/L&T

S&F MCB single pole 240 volt, 10 KA, 5-32 Amp, 'C' series confirming to IS complete all as specified and directed.

S&F MCB SPN 240 Volt 10 KA 32 Amp 'C' series conforming to IS complete all as specified & directed.

PRAGATI ENTERPRISES

M/s RP AGRAWAL