Necessary Of Civil And Repairing Work For Aganvadi In Chandlodiya Ward And Other Ward in North West Zone.

Name of Work: Necessary Of Civil And Repairing Work For Aganvadi In Chandlodiya Ward And Other

Ward in North West Zone.

Sr. No Qty Items Per Amount Rs.

Excavation for foundation up to1.5 m depth including sorting

out and stacking of useful materials and disposing of

theexcavated stuff upto 50 Meter lead.(A) Loose or soft

soil (R & B S.O.R 2023-24 I.no. Item Code 04001A)

2 Upto 1.5 mt Depth 115.92 Cmt

2 1.5 to 3.0 mt.depth 128.52 Cmt

Filling available excavated earth (excluding rock) in

trenches, plinth, sides of foundations etc. in layers not

exceeding 20 cm. in depth consolidation each deposited

layer by ramming and watering.

Providing and laying cement concrete1:5:10 (1-Cement: 5-

coarses sand and:10-hand broken stone aggregates 40mm

nominal size) and curing complete excluding cost of

formworkin (A) Foundation and Plinth.

Providing and laying cement concrete1:4:8(1-Cement 4-

coarses and:8-hand broken stone aggregates 40mm nominal

size) and curing complete excluding cost of formworkin(A)

Foundation and Plinth

Providing and laying cement concrete1:3:6 (1-

Cement: 3- coarses sand and:6-hand broken stone

aggregates 40mm nominal size) and curing complete

excluding cost of formworkin (A) Foundation and Plinth.

Providing and laying cement concrete 1:3:6 (1-Cement:3-

coarse sand:6-crushed stone aggregates 20mm nominal

size) and curing complete including cost of formwork in (A)

wall caps/coping

Providing and laying cement concrete work 1:2:4 ((1-Cement:2-

7 coarse sand:4-graded aggregates 20mm nominal size)

curing complete excluding cost of formwork and reinforcement.

Foundations, footings, base or columns and mass

Slabs, landing, shelves, balconies, lintels, beams,

girders and cantilivers upto floor two level

c 2 Independent piers, columns, and pillars, upto floor two level 3661.3 Cmt

Provdg. & laying cement concrete 1:2:4 (1 cement :

coarse sand : 4 graded stone aggregates 20 mm minal size)

for reinforced concrete chhajjas not exceeding 10 cm.

thickness upto floors two level including finishing the

exposed surfaces with cement mortar 1:3 (1 cement : 3 find

sand) to give a smooth and even surface centering and

formwork and curing complete excluding cost of

Providing and laying controlled cement concrete /

Ready Mix Concrete of M-200 and curing complete,

excluding the cost of form work and reinforcement for

reinforced concrete work in:

(A) 2 Foundations, footings, base of columns, and mass concrete. 3977.88 Cu.M.

(B) 2 Walls from top of foundations /level up to floor Two level. 4484.17 Cu.M.

Slabs,landing,shelves,Balconies Lintels, Beams, Girders and

Cantilever upto floor

(D) 2 Columns, pillars, posts, and struts, up to floor two level. 4558.2 Cu.M.

(E) 2 Staircase up to floor two level. (excluding landing) 5418.91 Cu.M.

(K) 2 Vertical and horizontal fins up to floor two level. 4701.97 Cu.M.

Providing and Laying ordinary cement concrete 1:2:4 (1-

Cement 2-coarsesand: 4-graded stone aggregates

mm nominal size) and finishing smooth with curing etc.

complete including the cost of form work but excluding the cost

of reinforsement for R.C.C work in (iv) Slabs having more

than 13 cm and upto 15 cm.thickness

Providing and Laying ordinary cement concrete 1:2:4 (1-

Cement 2-coarsesand: 4-graded stone aggregates

mm nominal size) and finishing smooth with curing etc.

complete including the cost of form work but excluding the cost

of reinforsement for R.C.C work in (iv) Slabs having more

than 8 cm and upto 10 cm.thickness

Brick work using common burnt clay building bricks

having crushing strength not less than 35kg./Sq.Cm.in

foundation and plinth in Cement Mortar1:6 (1-Cement :6

2 (A) Conventional (upto 10 ton) 3981.21 Cmt

2 B) Modular 4241.7 Cmt

Extra Rate for brickwork in Above Item for super

13 structure above plinth level upto floor two level (B)

a 2 (A) Conventional 272.25 Cmt

b 2 B) Modular 262.35 Cmt

c 2 C) above floor two level Item No. 2(6.13) (A) Modular 42.66 Per Cum

d 2 D) above floor two level Item No. 2(6.13) (B) Conventional 40.09 Per Cum

Half brick masonry in common brunt clay building bricks

having crushing strength not less than 35 Kg/Sq.Cm. in

Cement mortar 1:5 ( 1-Cement : 5 coarse sand ) in

foundation and Plinth conventional brickwork

Extra for half brick masonry in super structure above

15 2 plinth level upto floor two level (B) conventional

Providing form work in ordinary timber planking so as to

give a rough finish including centering, shuttering,

strutting and propping etc. height of propping and

centering below supporting floor to celling not exceeding

M & removal of the same for in situ reinforced or plain

concrete work upto floor four level

Foundation, footings, bases of columns etc. and mass

(B) Flat surfaces such as soffits of supspened floors slabs

b 2 Landings and the like. (1) Floors etc. upto 200 mm in 252 Smt

(B) Flat surfaces such as soffits of suspended floor roof slabs

c 2 Landings and the like. (2) Floors etc. above 200mm in 270.9 Smt

Vertical surface such as walls (any thickness) partitions and

d 2 the like including attached buttresses & string course & the 229.95 Smt

(ii) Sides And Soffits Of Beam, Haunchings Cantilevers,

e 2 Girders, Bressumers And Lintels Not Exceeding 1 M In 192.15 Smt

(G) Columns PillarsPosts and struts. (1) Square Rectangular

Polygonal in plan.

g 2 (2) Circular or curved in plan. 422.1 Smt

(H) (2) Sides and soffits of Beams Beam Haunchings canti-

levers Girders Bressumers and Lintels exceeding 1M.in Depth.

Providing and fixing 35 mm thick panelled, glazed or

panelled and glazed shutters for Doors windows and clear

story windows including anodised alluminium But hinges

with necessary screws and indian teak wood shutters with.

a 2 (A) Plywood sheet panels. 3459.09 Smt

b 2 (B) Particle board panels 3464.51 Smt

c 2 (C)Hard board panels. 3433.65 Smt

d 2 (D) Asbestos sheet panels. 3406.53 Smt

Providing and fixing 25 mm thick shutters for cup

boards etc. including black enamelled M.S. butt hinges

with necessary screws.(A) Indian teak wood. (i) Fully

Providing and fixing 25 mm thick shutters for cupboards etc.

a 2 including anodised alluminiu butt hinges with necessary 3006.75 Smt

screws. (A) Indian teak wood. (ii) Fully Glazed.

Providing and fixing 25 mm thick shutters for cupboards etc.

including anodised alluminiu butt hinges with necessary

screws. (A) Indian teak wood. (ii) Partly panelled and partl

Providing and fixing M.S. grills of required pattern to

wooden frames of windows etc. with M.S. flats at required

spacings and frame alround, square or round bars with

round headed bolts and nuts or by screws (A) Plain Grill.

Providing and fixing glazed louvered glass

windows and ventilators with teak wood frame 10 cm. x

7 cm. size including 3 coats of oil painting to wood work

Providing and fixing glazed louvered glass

windows and ventilators with teak wood frame 10 cm.x7

cm. size including 3 coats of oil painting to wood work

etc.complete.with wooden louvers plank 12mm thick

Providing and fixing 35 mm thick shutters for Doors,

windows and clere story windows including Indian teak

wood frames 10 cm x 7 cm. size including anodized

alluminium fixtures and fastenings including primer coat of

approved quality and two coats of oil painting etc, complete.(ii)

Providing and fixing 35 mm thick shutters for Doors,

windows and clere story windows including Indian teak wood

frames 10 cm x 7 cm. size including black enamelled iron

oxidixed fixtures and fastenings including primer coat of

approved quality and two coats of oil painting etc,

complete.(ii) Fully Panelled.

Providing and fixing 35 mm thick shutters for Doors, windows

and clerestory windows including Indian teak wood frames

cm x 7 cm. size including anodized alluminium fixtures and

fastenings including primer coat of approved quality and two

coats of oil painting etc, complete. (iii) Partly panelled and

Providing and fixing 30 mm thick FACTORY MADE SOLID

PANEL PVC DOOR SHUTTER consisting of frame made out

of M.S.tubes of 19 gauge thickness and size of 19 mm x

mm for stiles and 15 mm x 15 mm for top and bottom rails.M.S.

frames hall have a coat of steel primers of approved

make and manufacture, M.S. frames hall be covered with

mm thick heat moulded PVC ‘C’ channel of size 30 x

mm formings tiles, and 5 mm thick 75 mm wide PVC sheets

for to prail, lock rail and bottom rail on either side, and 10 mm

(5 mm x 2) thick, 20 mm wide cross PVC sheet as gap

insert for top rail and bottom rail, Panelling of 5 stiles and

rails with 30 mm wide x 5 mm thick PVC sheet beading

on eighter side, and joined together with solventcement

adhesive,. An additional 5 mm thick PVC strip of 20 mm width

is to be stculkon the interiors side of the ‘c’ channel

using PVC solvent cement adhesive etc. complete

as per direction of Engineer incharge, manufacture’s

specification and drawing.

Providing and fixing in position collapsible steel

shutters with vertical channels 20 x 10 x 2 mm braced

with flat iron diagonal 20 x 5 mm size with top and bottom

25 2 rails T iron 40 x 40 x 6 mm with 38 mm dia steel pulleys 5391.23 Sq.M.

complete with bolts, nuts, locking arrangements, stoppers,

handles, including a priming coat of red lead paint &

Providing and fixing 1 mm thick M.S. sheet sliding

shutters with frame and diagonal braces of 40x40x6 mm

angle iron, 3.15 mm M.S.gusset plates at Junctions and

26 2 corners 25 mm dia. pulley, 40x40x6 mm angle 3652.12 Sqm

and T-iron guide rail at top and bottom respactively

with handles, stoppers and locking agangement etc,

including applying a priming coat of red lead paint.

Providing & Fixing in position Alluminium doors with frame

using approved quality anodised extruded alluminium

section as approved by Engg.in charge(Jindal

alluminium) (a) Frame sections 101.6x44.45 mm (b) Shutter

bottom vertical & top section 83.5x44.45 (wt.1.31 kg/mt.)(at

1.31 kg/mt) (c) Shutter bottom section at 114.3x44.45

27 2 mm at(1.37kg/mt) Shutter middle section at 100x44.3 wt.(1.37

kg/mt) incl.providing & installing 5 mm thick approved

color Acrylic sheet of standard quality fixed with glazing chips

on upper pannel & Laminated sheet on lower pannel

(wtt.0.13 kg/Rmt) etc. comp.as direction of engg.in

Providing and fixing extruded aluminum window having

extruded aluminum Colour r Powder Coated section frame

main outer size 127mm x 38.10mm x 1.35mm ,@ Wt.1.384

Kg/mt,horizontal Four track member size 122.20mm x

31.75mm x 1.10mm @ Wt. 1.205 Kg/mt,vertical member of

size 122.20mm x 31.75mm x 1.50mm ,@ Wt. 1.398 Kg/mt with

sliding shutters of horizontal member size 40mm x 18mm x

1.29mm @ wt.of 0.456Kg/mt,vertical member of size 40mm x

18mm x 1.29mm @ wt.of 0.456Kg/mt,@ with 5 mm thick

transparent bronze colour tinted float glass with powder coated

aluminum fittings and fixtures and transparent silicon sealant

glass fixing to frame as per details etc complete for window.

Providing & Fixing in position Alluminium vents with frame

using approved anodised extruded alluminium section as

approved by Engg. In charge.(Jindal alluminium)

29 2 units equivalent Approved Rate)Frame section of 63.50 x 1,950.00 Sq. M.

38.50 mm. (wt. 0.68Kg/Rmt) incl. Providing & Installing

mmthick approved color Acrylic sheet of standard

quality etc. comp.

Providing and fixing standared extruded of alluminium

section of size 63 mmx38.10 mmx1.2 mm (Jindal

30 2 Section:2434, or equivalent @ Wt.0.643 Kg/mt) with 1163.92 Sq. M.

colour anodized alluminium frame for ventilation with

mm thick frosted glass as details etc complete for Ventilation

Providing and fixing standared extruded of alluminium section

of size 63.50 x 38.10 x 1.95 mm,@ Wt 1.094Kg / Rmt with

31 2 colour Powder Coated alluminium frame with 5 mm thick 2,141.88 Sq.M.

transparent bronze colour tinted float glass as details etc

complete for Fix Partition

Providing and laying 40 mm thick marble chips flooring

rubbed and polished (I.E.terrazo) to granolithic finish with

under layer 30 mm thick cement concrete1:2:4 (1-Cement: 2-

coarse sand:4-graded stone aggregate 10 mm and down

gauge) and to player 10 mm thick with white, black or white

32 2 and blak marble cihps of required sizes from 1 mm to 4 mm 811.13 Sqm

nominal size laid in cement marble powder mix 3:1 (3-

Cement:1-Marble powder by weight) in proportion of 4:7

(4- Cement: 7-marble chips by volume) (C) Medium

Shade pigment with approx 50% white cement and 50%

ordinary cement (In top layer only) (upto 10 ton)

Providing and laying marble chips skirting (Terrazo) or

dedo rubbed, and polished to Granolithic finish to player

mm white, black or white and black marble chips of

size from smallest to 4 mm nominal size laid in cement

marble powder mix 3:1 (3-Cement: 1 marble powder by

weight) in proportion of 4:7 (4-cement marble powder mix: 7-

marble chips by volume) (B) Light shade pigment with white

cement (In top layer only)

Providing and laying white glazed tiles 6mm thick in flooring

treads of steps and landing laid on a bed of 12mm thick

34 2 cement mortar 1:3 (1-cement : 3-coarse sand ) finishing with

Providing and laying Ceramic tiles 6 mm thick in flooring

treads of steps and landing laid on a bed of 12 mm thick

cement mortar 1:3 (1- cement :3-coarses and) finishing with

flush pointing in white cement.

Providing & Fixing 20 mm thick Mirror Polished Decorative

Granite Board with Computerised Golden Letters

36 2 Discription as per instructions of engg. in charge to 4,304.00 No.

M.S. frame structure for Inaugaration & Public

Handover Function (N.S.)

Providing and laying Vitrified tiles 8 to 10 mm thick, 36''x36'' in

flooring treads of steps and landing laid on a bed of

mm thick cement mortar 1:3 (1-cement:3-coarses and)

finishing with flush pointing inwhite cement.

Providing and laying Vitrified tiles 8 to 10 mm thick, 24''x24'' in

skrting risers of steps and dedo on 10 mm thick cement

plaster 1:3 (1- cement: 3-coarse sand) and jointed

with white cement slurry

Providing and laying Vitrified tiles 8 to 10 mm thick, in skrting

risers of steps and dedo on 10 mm thick cement plaster

1:3 (1-cement:3- coarse sand) and jointed with white

Providing and laying Vitrified tiles 8 to 10 mm thick , 24'' x 24''

in flooring treads of steps and landing laid on a bed of 12mm

40 2 thick cement mortar 1:3 (1- cement : 3-coarse sand ) finishing

with flush pointing in white cement.

P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm

(average) base of cement mortar 1:6 ( 1 cement: 6 coarse

sand) on new surface or fixing on, existing flooring by adhesive

41 2 material including dismentaling of existing flooring and jointed

with color cement slurry including finised with flush pointing &

cleaning the surface etc. complete for antiskit

Providing and laying polished Kota stone slab flooring over

20 mm (Average) thick base of cement mortar 1:6 (1-

cement:6-coarses and) or L.M.1.1.5 (1-Lime putty:1.5-coarses

and) laid over and jointed with grey cement slurry mixed

with pigment to match the shade of slab including

rubbing and polishing etc. complete. (A) 25 mm thick

Providing and laying marble stone slab flooring over 20mm

(average)base of cement mortar 1:6 (1-cement : 6 coarse

43 2 sand) or L.M. 1:1.5(1- lime putty : 1.5 - coarse sand) laid and 2194.63 Sq.M.

jointed with gray cement slurry including rubbing and polishing

complete. (A) Marble slab 25mm thick

Providing and laying polished Kota stone slab flooring over

20 mm (Average) thick base of cement mortar 1:6 (1-

44 2 cement:6-coarses and) or L.M.1.1.5 laid over and jointed 1085.48 Sq.M.

with grey cement slurry including rubbing and polishing

etc.complete. (B) 30 mm thick

Providing and laying polished kota stone slab 25 mm thick in

risers of steps, skirting Dedo and pillars laid on 10 mm thick

cement mortar 1:3 (1-Cement :3 coarses and) and jointed

with gray cement slury mixed with pigment to match the

shade of slab including rubbing and polishing

Providing and laying cement concrete flooring 1:2:4

(1-cement: 2-coarses and:4-graded stone aggregate

20mm nominal size) laid in one layer and finished with a

floating coat of neat cement. (A) 40mm thick.

Providing and laying cement concrete flooring 1:2:4

(1-cement: 2-coarse sand:4-graded stone aggregate

20mm nominal size) laid in one layer and finished with a

floating coat of neat cement. (B) 50mm thick.

Providing and laying broken china mosaic flooring for

terrace using 12 mm to 20 mm broken pieces of glazed tiles to

be laid over cement mortar 1:3 to plain or slope and to be

48 2 tempered to bring mortar creme out upto surface using 739.89 Sqm

white cement including rounding off junctions and

extending them up to15 cm along the wall, clearing with

water and oxalic acid etc.as directed.

Providing and laying coloured glazed tiles of the

size 300 mmx200 mmx8 mm/300 mmx450 mmx8 mm in

49 2 skirting, risers of steps and dedo on 10 mm. thick 1426.95 Sqm

cement plaster 1:3 (1cement: 3 coarse sand) & jointed

with white cement slurry.

Providing ridges or hips 600 mm overall in plain G.I. sheet

class-3 fixed with G.I. J or L Hooks and nuts 8 mm dia

G.I. Limpet and bitumen washer complete. (1) 0.80 mm thick

Providing and fixing 150 mm wide 450 mm over all semi

circular plain G.I.sheet class-3 gutter with Iron brackets

51 2 mmx3 mm size Bolts, Nuts, washers etc. including 555.71 Sqm

making necessary connection with rain water pipes. (i)

mm thick Sheet.

Providing and fixing five courses water profing

treatment with bitumen felt consisting of second and

fourth course of blown/ bitumen or/and residual

bitumen applied hot at 1.2 kg.per Sq.M.of area for each

course and first course with fibre base bitunen

saturated under lay type land third course with fibre base self

finished felt type 2 grade 1 and fifth and final course of

stone grit 6 mm and down size or pea sizes gravel

spread at 0.008 Cu.Metre/Sq.metre preparation of surface

excluding grading complete.

Providing and fixing on wall face C.I. Rain water pipe

including filling the joints with spun yarn soaked in neat

cement slurry and cement mortar 1:2(1- Cement : 2-

fine sand) (A) 75 mm dia.

Providing 15 mm thick cement plaster in single coat on

Rough (Similar) side of single or half brick walls for interior

plastering up to floor two level and finished even and

smooth in (i) Cement mortar 1:3 (1-cement :3-sand)

Providing 20mm thick sand faced cement plaster on walls upto

height 10 metres above ground level consisting of 12mm thick

backing coat of C.M. 1:3 (1-cement : 3-sand) and 8mm thick

finishing coat of C.M. 1:1 (1-cement : 1-sand) etc. complete.

Colour washing with lime on wall surface (two coats)

over and including a primary coat of white washing to

56 2 give an even shade after through brooming the surface to 12.29 Sqm

remove all dirt, dust, mortar drops and other foreigh

Removing dry or oil bound distemper by a

washing and scraping and sand papering the wall

surface smooth including necessary repairs to

scratches complete.

Distempering with dry distemper of approved brand and

manufacture (two coats) and of required shade on wall

surfaces of given an even shade, over and including

a priming coat of whiting after thoroughly brooming

the surface free from mortar dropping and other foreign

Distempeing (Two coats) with oil bound distemper of

approved brand and manufacture and of required shade

on wall surfaces to give an even shade, over and

including a priming coat with distemper primer of

approved brand and manufacture after thoroughly

brushing the surface free from mortar dropping and

other foreign matter and also including preparing the

surface even and sand papered smooth.

Extra Coat for Above Item over above for every

subsequent coat of approved brand and manufacture.

Wall painting (two coats) with plastic emulsion paint of

approved brand and manufacture on undecorated wall

61 2 surface to give an even shade including throughly brushing 78.44 Sqm

the surface free from mortar droppings and other foreign

matter and sand papered smooth.

Extra over item for every sub sequent coat of wall painting

with plastic emulsion paint of approved brand

Extra over item for painting with plastic emulsion paint of

approved brand on ceilings and sloping roofs.

Applying priming coat over new steel and other metel

surface after and including preparing the surface by

throughly cleaning, oil, grease, dirt and other foreign

matter and scoured with brushes fine steel wood, scrapers

and sand paper with ready mixed priming paint brushing

Painting two coats (excluding priming coat) on new

steel and other metal surface with enamel paint, brushing,

64 2 interior to give an even shade including cleaning the surface 86.94 Sqm

an even shade including cleaning the surface of all dirt, dust

and other foreign matter.

Painting one coats (excluding priming coat) on previously

painted steel and other metal surface with enamel paint,

brushing to give an even shade including cleaning the

surface of all dirt, dust and other foreign matter.

66 2 Extra over item for every sub sequent coat of paint. 50.4 Sqm

Painting two coats (excluding priming coat) on new

steel and other metal surface with synthetic enamel paint,

brushing to give an even shade including cleaning the

surfaceofalldirt,dust and other foreign matter.

Painting one coats (excluding priming coat) on previously

printed steel and other metal surface with synthetic enamel

paint, brushing to give an even shade including cleaning

the surface of all dirt, dust and other foreign matter.

69 2 Extra over Above item for every sub sequent coat of paint. 43.47 Sqm

Painting two coats (excluding priming coat) on external

surface of new rain water, soil, waste and vent pipes and

70 2 fittings with ready mixed bituminous brushing, black, anti 20.16 Sqm

corrosive to give an even shade including cleaning of all

dirt, dustand other foreign matter.(75 mm dia)

Painting two coats (excluding priming coat) on external

surface of new rain water, soil, waste and vent pipes and

71 2 fittings with ready mixed bituminous brushing, black, anti 25.05 Sqm

corrosive to give an even shade including cleaning of all

dirt, dust and other foreign matter.(100 mm dia)

Painting two coats (excluding priming coat) on new

wood and wood based surface with enamel paint, interior

to give an even shade including cleaning the

72 2 surface of all dirt, dust and other foreign matter sand

papering and stopping. (a) Ready mixed paint brushing wood

Painting one coats (excluding priming coat) on previously

painted wood and wood based surface with enamel paint,

73 2 to give an even shade including cleaning the of all dirt, dust 26.78 Sqm

and other foreign matter.(b) Ready mixed paintbrushing

priming for enamel

74 2 Extra over Above item for every sub sequent coat of paint. 24.26 Sqm

Painting two coats (excluding priming coat) on new wood

and wood based surface with ready mixed paint,

75 2 brushing, oil, gloss, semi gloss to give and even shade 104.12 Sqm

including cleaning of all dust, dirt and other foreign

matters and papering and stopping.

Finishing wall with weather proof exterior emulsion paint

on wall surface (two coats) to give an required shape

76 2 even shade after thoroughly brushing the surface to remove 113.4 Sqm

all dirt, and remains of loose powdered

materials.etc complete

Applying two coats of Birla (white cement based) or

Asian (acryliclapy-putty) or equivalent & two coats of primer

of approved brand and manufacture on new wall surface

to give an even shade including thoroughly brushing the

surface free from mortar dropping and other foreign matter

and sand papered smooth.

Painting one coats (excluding priming coat) on previously

painted wood and wood based surface with enamel paint, to

give an even shade including, cleaning the of all dirt, dust and

other foreign matter.

Writing etter or figures on any surface with black japan

paint (stops, comas, hyphens and the like not to be

measured and paid for separately) (i) Block

(Letters/Figures) (Per 10 Letter pet CM.HT) Cm/Ht

Demolition including stacking of serviceable materilas and

80 2 disposal of unserviceable materials with all lead and lift. (i) 1047.38 Cu.M.

Demolition of Brick work and stone masonry including

stacking of serviceable materil as and disposalof

unserviceable materials with all lead and lift.(ii) In Cement

Dismentaling tiled of stone floors laid in mortar including

82 2 stacking of serviceable materil as and disposal of 47.25 Sqm

unserviceable materials with all lead and lift.

Dismentaling of sheet roofing including ridges, Hips,

Valleys, Gutters etc. stacking of serviceable materil as

and disposal of unserviceable materials with all lead

and lift.(i) G.I.sheet roofing.

Dismentling steel work including distempering and

84 2 stacking the materials with all lead and lift.

Dismentling doors, windows, ventilators etc. (wood

or steel) shutters including chowkhats architraves, hold

85 2 fasts and other attachment etc. complete and stacking 185.85 Each

the material within all lead and lift.(i) Not exceeding 3 Sq.M. in

Dismentling doors, windows, ventilators etc. (wood

or steel) shutters including chowkhats architraves,hold

86 2 fasts and other attachment etc. complete and stacking 248.85 Each

the material with in all lead and lift.(ii) Exceeding 3 Sq.M.in

Dismentling barbed wire in fencing including making rolls

and also including dismentling fencing posts including all

earth work concrete in base and making good the disturbed

ground stacking useful materials as directed and

disposing as directed and disposing of the unserviceable

materials with all lead and lift.

Dismentling C.Ipipes G.S.W. pipes abd A.C. rain water

88 2 pipes with fittings and clamps including stacking the 74.03 Rmt

materials with all lead and lift (for any dia, of pipe)

Dismantling santtary fittings like wash basin . W.C. pan Indian

89 2 and Europe an type, flushing tank etc. including stacking 401.63 Each

the materials with all lead and lift

Scraping oil paint from steel and other metal surface and

making the surface even (with Hand Scraping.)

Removing and scraping of old deteriorated plaster

of any thickness from wall / R.C.C member

including stacking of serviceable material and disposal of

unserviceable from site of work with all lead and lift

Providing and fixing M.S. fan clamps of shape and

92 2 size as specified in existing R.C.C. slab including cutting 168.53 Each

chase and making good.

Cutting out cracks of roof terrace to V-section, cleaning out,

93 2 wetting, grouting with cement and sand slurry 1:3 (1- 64.58 Rmt

cement 3-sand )

Cutting out cracks roof terrace to V-Section cleaning out

94 2 and filling solidly with a hot mixture of bitumen and 75.29 Rmt

clean dry sand (1:1 by weight)

Providing & Fixing in position Alluminium doors with

frame using approved quality anodised extruded

alluminium section as approved by Engg.in charge(Jindal

alluminium)(a) Frame sections 101.6x44.45 mm (b)

Shutter bottom vertical & top section 83.5x44.45

(wt.1.31 kg/mt.)(at 1.31 kg/mt) (c) Shutter bottom section at

95 2 114.3x44.45 mm at (1.37 kg/mt) Shutter middle section at

100x44.3 wt.(1.37 kg/mt) incl.providing & installing 5 mm

thick approved color Acrylic sheet of standard quality

fixed with glazing chips on upper pannel & Laminated

sheet on lower pannel (wtt.0.13 kg/Rmt) etc.comp.as

direction of engg.in charge.(N.S.)

Providing & Fixing in position Fully Panelled / Partly Panelled

Partly Glazed / Fully Glazed Alluminium doors with frame

using approved quality anodised extruded

alluminium section as approved by Engg. In charge.(Jindal

alluminium )(a) Frame sections 101.6x44.45 mm b)

Shutter vertical & top section 83.5x44.45 (wt.

96 2 kg/mt.)( at 1.31 kg/mt) © Shutter bottom section at 114.3 4,583.00 Sq.M.

x44.45mm at ( 1.37 kg/mt ) Shutter middle section at

100x44.3 wt. (1.37 kg/mt ) incl. providing & installing 5 mm

thick Glass of standaed quality fixed / 12 mm thick

Laminated sheet with glazing chips (wt. 0.13 kg/ Rmt) in

panels etc. comp. as per Detail Given & direction of

engg.in charge.

Providing & Fixing in position Alluminium window

2/3/4 track sliding / fix type with frame using approved

anodised extruded alluminium section as approved by Engg.

97 2 In charge.(Jindal alluminium) units equivalent.

including P/F installing 5 mm thick clear/tinted Glass of

standard quality etc.comp.

Providing & Fixing in position Alluminium vents with frame

using approved anodised extruded alluminium section as

approved by Engg. In charge.(Jindal alluminium)

98 2 units equivalent Frame section of 63.50 x 38.50 mm.

(wt.0.68 Kg/Rmt) incl. Providing & Installing 5 mm

thick Glass of standard quality etc. comp.

Providing and fixing of Ridge flashing for roof panel

shall be made out of 0.5 mm thick pre coated GI

sheet. The Pre coatedsheet shall be of minimum

mpa steel grade confirming to IS 14246:1995 and shall

have zinc coating of minimum 120 gsm as per

IS:277:1992, 5-7 microns epoxy primer on both side of

99 2 the sheet and polyester top coat 15-18 micron. The PP GI

Sheet shall have plastic protective guard film of minimum

25 microns to avoid scratches during transportation. The

ridge shall be fixed to the steel members by poprivetor

self drilling/self stitching fastners @ maximum 450mm c/c

along length of capping/flashing etc complete .

Supplying and fixing vinyl flooring over the surface having

100 2 1-2 mm thickness as per directed by engineer 963 Smt

incharge etc as completed (N.S.)

Providing and laying 15mm bamboza wooden flooring

as per architect's drawing with all necessary details

101 2 as directed by the project consultants. Use underlay 2,690.00 Smt

for better result as per Detail specifications and directed

by the project consultants. (N.S.) Approved Rate )

Providing and fixing 1.20 Metre high fencing with

Metre long M.S. Angle posts 40 mm x 40 mm x 6 mm and

oil painting 3 coats fixed at 2.5 Mt, C/c. with five

Horizontan lines and two diagonals of galvanised steel

barbed wire weighting 9.38 Kg. per 100 Metre, strained and

fixed to posts with G.I, staples including fixing the posts

in ground with 0.5 M x 0.5.M x 0.5 M. block in C.C 1:5:10

Renovation and Repairing work in Chainlink fencing any

size and also refixing work incl. febrication work with all

103 2 materails to be painted one coat of primer and twocoats

of paint as directed inline and level. (N.S.)

Constructing a sink (chowkedi) with C.C. 1:2:4, 12 cm.

thick over B.B. masonry in C.M, (1:6) in front and dwarf wall

104 2 1.0 Mt. high and 23 cm. thick cement plaster to 2235.66 Rmt

masonry / in C.M.1:3) and cement concrete flooring in 1:2:4:

mix 5cm.dia.drain pipe etc.complete.

Constructing a cooking platform 60 cm. width and 70 cm

high resting on B.B. Masonry walls 23 cm. thick in C.M.

(1:6) with (i) Fixing or precast R.C.C. 1:2:4) 8 cm. thick

slab with marble chips set in C.M. (1:6) (6 mm thick

terrazo) with plastering on exposed faces walls in C.M.

(1:4) etc complete.

Extra rate for using Ready Mix Concrete of any grade

for below ground level to vertical upto any floor with

106 2 delivery & suction Pipe & Pump etc. The rate includes fule, 760 Cmt

pump operator, skilled labor, driver etc completed and as per

direction of engineer in charge

P/A Tremix with dewartering machine and floater

machine on constructed CC work for finishing the surface

107 2 as per requirement. The rate including all machinaries, 54 Sq.M.

labor, loading, unloading, transportaion etc

complete as per direction given by engineer incharge.

Carrying out timber treatment to all wood work including drilling

holes and spraying oil based chemical solution on surface of

timber work for termite control including labor and material etc.

complete. Using Chlorpyriphos20 EC as per 6313 2013 Part III

(1% concentration by mass) is recommended one litre

chemical emulsion diluted with 19 liters of kerosene. Total

diluted concentration will be 20 liters inclusive of 1 liter

chemical emulsion application in drilled holes and 0.75 / Litre

chemical per one Sqmt two coat on wood surface not protected

by paint or varnish.

Applying general insecticide pest control treatment to floors,

cupboards etc including labour materials etc. complete. Using

Imidacloprid 30.5 SCas Per IS 6313 part -II( (0.075%

concentration by mass) is recommended 10.5ml chemical

diluted with 5 liters of water application 0.5 litre chemical /Sqm

of, surface is recommended as per I.S.

Carring out plinth treatment to post construction / existing

structure by spraying chemical solution for termite

control treatment including labour and material consist ment

with I.S.specification. Using Chlordene and Chior purfiles

110 2 20 EC. As Per 6131_paret-II Consentration Weight on 104.9 Smt

percentis recommended i.e one litre 20 EC chemical

emulsion with 19 liter give 1% concrentration inclusive of

one litre chemical emulsion appication attherate of 5 Litre

chemical /Sqm of surface is recommended as per I.S

Carrying out wall treatment for termite control including

spraying with chemical solution in oil base including labour and

material Using Chlorpyriphos 20 ECAs per IS 6313 part - II (1%

concentration by mass) is recommended i.e one litre chemical..

emulsion diluted with 19 liter oil base. Total solution will be

liters inclusive of one liter chemical emulsion application at the

rate of 7.5 litre chemical / Sqm of surface is recommended as

Providing erecting and fixing double coated Syntex

or equivalent PVC.(ISI) water tank of required capacity

112 2 3.91 Litre

each with all necessary fittings and connection etc.

complete on terrace.

Providing and fixing to wall, ceiling and floor galvanised

Mild steel tubes (Medium grade) of the following

nominal bore, tube fitting and clamps including making good

the wall ceiling and floor.

2 (F) 50mm 779.6 Rmt

Providing and laying in trenches galvanised mild steel

tubes (Midium grade) of the following nominal bore,

and tube fitting (Earth work in trenches to be

measured and paid for separately)

Making connection of galvanised Mild steel distribution

branch with galvanised mild steel main 50 mm to 80 mm

nominal bore by providing and fixing tee including cutting

and threading the pipes complete.

Providing and fixing to wall ceiling and floor 6.0 Kg.F/Cm2

working pressure poluthene pipes of the following out side

116 Dia. Low densidy, complete with special falnge compression

type fittings,wall clips etc. including making good the wall

ceiling and floor.

Providing and fixing to wall ceiling and floor 10.0 Kg.F/Cm2

working pressure polythene pipes of the following out side

117 Dia Low densidy, complete with special falnge

compression type fittings, wall clips etc. including making

good the wall ceiling and floor.

2 (C) 32mm 116.4 Rmt

Providing and fixing cast iron (Spun) Nahni trap of the

following nominal diameter of self cleaning design with C.I.

118 2 screaed down or higned grating including cost of cutting 600.08 Each

and making good the walls and floor 100 mm inlet and 50 mm

outlet.(C)100mm dia.

Providing and fixing water closet squatting Pan (Indian

type W.C.Pan) size 580 mm (Earth work, bed concrete,

foot rest and trap to be measured and paid for separately)

(A) Vitreous China. (I)Long pattern = White colour

Provdg. & fixing wall mounted White / Color Vitreous

China European water closet with integral P trap of "Cera" -

120 2 Clair Series or equivalent incl. seat cover , Chair Bracket

etc. complete as per direction of engg. In charge.(N.S.)

Providing and fixing wsh down water closet (Europe

an type, W.C.Pan) with integral P or S trap including jointing

the trap with soil pipe in Cement Mortar1:1 (1-

Cement:1-fine sand) (Seal and cover to be measured and

paid forseparately) (A) vitreous China Pattern :(i) in white

Provdg. & Fixing Flat Back Large Urinal of White/ colour of

"Cera" or " Hindware" incl. C.P. Brass waste coupline

122 2 waste pipe, pvcconnection etc. Complete.( size

Providing & Fixing Angle cock of " Ess Ess" - Trend

123 2 series or equivalent standard make as approved by 675 No.

engg. in charge all complete. (N.S.)

Providing and fixing 100 mm size P or S trap for

water closet squatting pan including jointing the trap with the

pan and soil pipe in cement Mortar1:1 (1-Cement : 1-Fine

sand)(A) Vitreous China.

Providing and fixing wash basin with single hole for pillar

tap with C.I.or M.S. brackets painted white including sutting

125 2 holes and making good the same but excluding fittings. 1400.18 Each

(A) Vitreous China: (ii) Flat Back wash basin 550 mm x v

mm size.(i) In white colour.

Providing and fixing Kitchen sink with C.I. or M.S. brackets,

painted white including cutting holes in walls and making

good the same but excluding fittings. © Vitreous China

Sink. (i) 600 mm x 450 mmx 150 mm size

Providing and fixing 600 mm x 450 mm bevelled edge

mirrror of superior glass mounted on 6 mm thick A.C.

sheet or ply wood sheet and fixing to wooden pluge with

C.P. brass screws and washers.

Providing and fixing chromium plated brass halftrun flush cock

of approved quality including fixing in pipe line etc. complete.

Provdg. & fixing White / Color Vitreous china Counter

wash basin with signle hole for pillar tap of "Cera " -

Concord series of 550 x425 mm size to be fiited in stone

counter with necessary brackets painted white incl.

129 2 cutting holes and making good the same .Cost Includes 2,950.00 No.

P/F C.P. brass waste coupline, 32 mm dia fisher union

mm dia. Pillar cock & Angle cock of " Ess Ess"- Trend

series ,32 mm dia. Waste pipe etc. complete as per

dir. of engg. in charge.

Providing and fixing washbasin with single holefor pillar tap with

C.I. or M.S. brackets painted white including sutting holes and

130 2 making goodthe same but excluding fittings.(A) Vitreous 1400.18 No

China:(ii) Flat Back washbasin 550 mm x v400mm size. (i) In

Providing & Fixing S.S.304 Grade Sink of Nirali / Krishna or

131 2 Equivalent Make for Kitchen Platform of size : 24":x18" as 4,650.00 No.

per Direction of engg. In charge

Providing and fixing C.P. brass towel rail comlete with

132 2 C.P.brass brackets fixed to wooden plugs with C.P. 597.22 Each

brass scews.(B) 600mm x 20mm size.

Providing and fixing 600 mmx120 mm glass shelf with

133 2 C.P. brass bracket and guard rail complete mixed to 561.03 Each

wooden plug with C.P.brass screws.

134 2 Providing and fixing toilet paper holder. (A) C.P.Brass 414.53 Each

Providing and fixing screw down bib taps of following size.

(A) Brass screw down bib tap polished bright.

2 (i) 15mm dia. 184.98 Each

2 (ii) 20mm dia. 212.68 Each

Providing and fixing screw down bib taps of following size.

(B) Brass chromium plated screws down Bib Tap.

2 (i) 15mm dia. 184.98 Each

2 (ii) 20mm dia. 212.68 Each

Providing and fixing screw down bib taps of following size.

© Gun metal screw down bib tap.

2 (i) 15mm dia. 157.29 Each

2 (ii) 20mm dia. 176.09 Each

Providing and fixing pillar tap, capstan head, screw

down high pressure with screws, shanks and back nuts.

2 (i) 15mm dia. 305.67 Each

2 (ii) 20mm dia. 351.18 Each

Providing and fixing Gun metal check or non-return

fullway wheel valve.

2 (i) 15mm dia. 184.98 Each

2 (ii) 20mm dia. 201.8 Each

2 (III) 25 MM DIA 416.47 Each

2 (E) 40mm dia 656.86 Each

Providing and fixing chromium plated brass half trun flush

140 cock of approved quality including fixing in pipe line etc.

2 (i) 20mm dia. 252.26 Each

2 (ii) 25mm dia. 261.16 Each

2 (iii) 32mm dia. 273.03 Each

Providing and fixing Urinal or approved qualit including

conecting the Urinal with waste pipe, tap etc.complete. (A)

White earthen ware flat back or corner type size 430mm

Providing and fixing Urinal of approved quality

including connection with trap and with integral

longitudinal flush pipe. (A) Squating plate pattern white

earthen ware 550mm x 300mm.

Providing and fixing chromium plated, bottle trap with

necessary couplings of approved quality for wash basin.

Providing and fixing ball cock ofapproved quality as

directed. (A) Copper Metal (i) 25mm dia.

Providing and fixing ball cock of approved quality as

directed. (B)Abonite (i) 25mm dia.

Filling with good Quality thor as and where directed

by the Architect / Engineer-in-charge, in sunk in layers of

146 2 15 cm. thickness, including watering, ramming well etc.

complete, as directed by the Architect / Engineer-in-charge .

Providing laying and jointing in true line and level 15 mm dia.

U.P.V.C. Pipe (SCH-40) for cold water including fittings

make PRINCE/ SUPREME/ ASTRAL/ FINOLEX or equivalent

as approved by Engineer In Charge. Pipe shall be fixed

147 2 on the wall with the help of clamp at every two metre 71.93 Rmt

C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints

and fixing the same with solvent, including cost of all

materials.adhesive

Providing laying and jointing in true line and level 25 mm dia.

U.P.V.C. Pipe (SCH-40) for cold water including fittings

make PRINCE/ SUPREME/ ASTRAL/ FINOLEX orequivalent

as approved by Engineer In Charge. Pipe shall be fixed

148 2 on the wall with the help of clamp at every two metre 90.93 Rmt

C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent, including cost

of all materials.

Providing laying and jointing in true line and level 32 mm dia.

U.P.V.C. Pipe (SCH-40) for cold water including fittings

make PRINCE/ SUPREME/ ASTRAL/ FINOLEX or equivalent

as approved by Engineer In Charge. Pipe shall be fixed

149 2 on the wall with the help of clamp at every two metre 117.97 Rmt

C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent, including cost

of all materials.

Providing laying and jointing in true line and level 40 mm dia.

U.P.V.C. Pipe (SCH-40) for cold water including fittings

make PRINCE/ SUPREME/ ASTRAL/ FINOLEX or equivalent

as approved by Engineer In Charge. Pipe shall be fixed

150 2 on the wall with the help of clamp at every two metre 146.65 Rmt

C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent, including cost

of all materials.

Providing laying and jointing in true line and level 50 mm dia.

U.P.V.C. Pipe (SCH-40) for cold water including fittings

make PRINCE/ SUPREME/ ASTRAL/ FINOLEX or equivalent

as approved by Engineer In Charge. Pipe shall be fixed

a 2 on the wall with the help of clamp at every two metre 193.73 Rmt

C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent, including cost

of all materials.

Providing in line level plumb, fabricating and fixing

three row horizontal barbed wire fencing and punched tape

concertina coil of 9 turns per meter of 610 mm dia fixed

with clips on top of the angle iron posts. The punched

tape concertina coil having sharp barbs at every 25 mm

spacing shall be 0.5 mm thick and 19 mm width and weighting

13 kg/100 mt. (Average) as per manufacture's specification.

The rate shall also include providing and fixing

1.20 mt.total long MS angle 40 x 40 x 6 mm @3.00 mt.c/c

spacing embaded in RCC column, angle posts shall be

painted with one coats of red oxide and two coats of enamel

paint of approved quality at top compound wall.

Fixing sun film for protection sunlight in black or any colour as

152 2 as directd by engineer In Charge.(Market rate)

Providing & Fixing 3 mm thick F.R.P.sheet of Approved

Quality & Color / Pattern as per Consultant's design also

includes required fabrication structure in the grid of 2'-0x2'-

0 size using hollow pipe of16 gauge & size 2"x1" & 1"x1"

153 2 ,G.I. & Bitumen Washers, Silicon paste application for 1,930.00 SqM

fixing the sheet . Rate also includesnecessary bending,

cutting, labor charges , Zinc Primer coat & Two coats of oil

painting of color as approved by consultants & making

good the wall. (N.S.)

Providing 2 mm thick F.R.P. Gutter with necessary M.S.

154 2 Supporting Brackets. (N.S.)

Hiring charges for J.C.B.machine inclduing cost of fuel,

155 2 operator, dirver etc.. ( 12 hours sift day/night) 600 Hrs.

To provide tractor with hydraulic trolley, driver, 4 Nos. of

Labor with all tools like bucket drum, showels, trikam, pavadas,

etc, to carryout different works during monsoon for 12 Hrs.

156 2 Shift. Work shall be carried out as per the instrucitons of

Engineer In-Charge.No extra charged shall be paid for night

Roller Blind Providing and fixing Roller Blind curtain fixed

on window level on wooden batten and curtain lift with

cotton thin rope, make of aerolax or equivalent design and

157 2 colour as per instruction by engineer – in – Charge with

necessary hardware fitting, material and labour etc

Providing & Fixing Door closer - Door closers (Heavy type of

158 2 765 number) Hardwire or Everite Prabhat or Equivalent

Providing and fixiing M.S. Fan clamps type 1 of 16 mm dia

M.S. bar bent to shape with hooked ends of R.C.C. slabs

during laying incl. painting the exposed protion of loops, all as

per standard design complete.

Providing cement vata (10cm. x 10 cm. size) quarter round in

160 2 cement mortar 1:1 including neat cement finishing, watering 23.45 Rmt

161 2 Making Water connection from exi.Muni. Water line (N.S.) 250 No.

Providing and applying fibere reinforced cementitious

micro concrete work in cellings and beams incl.mixture of

CEMSCREED HM (F) fair mate company material, FBR

162 2 bonding agent material with water in suItable proportion anti 530 Smt

corrosive treatment on exposed beam,celling steel bars with

safeCore R incl.all kind of labour etc.comp.including three

coat of white wash.(Approved Rate)

Providing and Fixing 1 H.P. Electrical monoblock or

submarcible water pumps withmotor and required cable and

163 2 switch board of approved brand and make etc.comp.as

.Providing TMT Bar FE 415 reinforcement for R.C.C. work

163 a 2 including bending, binding and placing in position complete up 66.59 Kg.

to floor two level

ProvidingTMTBarFE500/500Dreinforcement for

R.C.C.workincluding bending,binding and placing in position

complete upto floor two level placing in position complete upto

floor two level placing in position complete upto floor two level

Providing and fixing 30mm thick solid both side prelam PVC

164 2 door shutter (sintex door-equivalent) with necessary alluminium 2,867.00 Smt

fitting with EL-7 section frame

Conveyance charge of Earth,Lime, Murrum, building rubbish

165 2 earch manure or sludge and excavated rock and fly 235.51 Cu.M.

ash,aggregate of any kind etc.comp.upto 5 km lead.(L.S.)

Providing and laying polished granite stone slab 18 mm thick in

risers of steps, dedo and pllars laid on 10 mm thick cement

166 2 mortar 1:3 (1 cement:3 coarse sand) and jointed with gray

cement slurry including rubbing & polishing etc.complete.

Wall panelling with 12 mm MDF fixed to existing alluminium

framing and making grove as per design and finished with

167 2 royal plastic paint as per instruction of engineer incharge.

Providing and laying 15mm bamboza wooden flooring

as per architect's drawing with all necessary details

168 2 as directed by the project consultants. Use underlay 2,690.00 Smt

for better result as per Detail specifications and directed

by the project consultants. (N.S.) (Approved Rate )

Applying two coats of Birla (whitecementbased) or Asian

(acryliclapy-putty) or equivalent & two coats of primer of

169 2 approved brand and manufacture on new wall surface to give 40.19 Sq.M.

an even shade including thoroughly brushing the surface free

from mortar dropping

Finishing wall with weather proof exterior emulsion paint on wall

surface (two coats) to give an required shape evenshade after

170 2 thoroughly brushing the surface to remove all dirt, and remains

of loose powdered materials.etc complete

Providing and fixing flush door shutters, solid core

construction with frame of first class hardwood with cross

board and face veneer or plywood face panels, with both

side 1 mm laminate finishing including anodized

aluminum butt hinges with necessary screws. Decorative

type and pine wood core anodized minimum 3 no

mm long aluminum butt hinges in flush door shutters with

171 2 2 no of brass holdfast 325 mm long 1 no brass tower bolt 4,686.36 Smt

250 mm long and two no of 150 mm long brass door handle

. Decorative both side laminated Flush door 35 mm thick.

with frame of 10 cm x 7 cmt Indian teak wood frame

including all necessary fitting fixtures hardware screw

and adhesive etc fixing up to all lead and lift height up to

45 mtr from GL etc complete as per direction of engineer

P/M/F chainlink jali 8'x4' size as per details sketch &

instructionof engineer in charge same as lal darwaja garden

pattern consisting of 3'dia. M.S black pipe 'A' class 5'4" ht.

fixed at 8'9" c/c in C.C 1:2:4 block of 9"x9"x9" size chain link jali

of size 2"x2"x10 gauge fixed in 35x35x5 mm MS angle frame

172 2 8'x4' size with MS flat of size 25x3 mm welded jali

etc.comp.The jali is to be welded to MS pipe with MS flat as

instruction given.The M.S pipe and the M.S angle frame are to

be painted one coat of primer and two coats of paint as

directed in line and level. (N.S)

Providing & Fixing masonary wall with porbandar lachiya stone

with well dressed grooveas per directed by engg.in charge for

foundation, plinth or super structure level (above plinth level

173 upto floor two level) in cement mortar 1:5 (1-cement : 5-fine

sand) incl.pointing the joint with white cement and yellow oxide

powder in proportion to match stone colour the joints should be

thread grooved as per exi. lake stone pitching apperance

(A) stone masonary wall/stone dressed single faced (size

2 (B) stone coping (size 15"x8"x4") 510 Rmt

2 (C) stone coping (size 15"x8"x9") 790 Rmt

2 (D) stone column (size 15"x15") 10,710.00 Cmt

2 (E) stone column top (size 20"x20"x9") 685 No.

Supplying and fixing of 300 mm-L x 15 mm-B x 380 mm-H

Kerb block for Footpath in M-20 grade using 20 mm

nominal size black trap aggregate of Sevaliya/Timbaor

equivalent quality for pre-cast blocks,

reasonablyexposed finish/ formwork , mould

with well equippedwith vibratory system for kerb stones

of approved design including curing, etc. complete,

including thecost of formwork etc. complete. The rate

shall also include necessary cutting of asphalt, fixing

174 2 the Kerbstones in line and level on 5 cm thick sand

bedding withnecessary equipments and

materials. The rate shall also include the flush pointing in

CM (1:3) for all joints of thekerbstones. Filling of zari alone the

sides of the kerbstone fixed with Bituminous

concrete Bituminousconcrete / C.C. mixed in proper

position to flush withthe road surface as dire

Engineer incharge, manufacture’s specification and

Providing and Laying of Rubber Moulded Paver Block

Grey/Coloured 60 mm thick, M-35 Grade of any size shape

(Usually Uni-Paver Blocks) using black trap good quality

aggragate of 20 mm nominal size for footpath,parking areas,

service lanes and other areas as mentioned in the drawing /

instruction of engineer in charge. Cost includes formworks

using rubber mould, Rate providing and laying paver blocks as

per required grading and specification. The paver block shall

175 2 be mechanically compacted. The work of paving blocks shall 429 Smt

be executed in line and level by skill mason of flooring work

only. It should be laid in such a way that the no cutting of the

paver block to be necessary. if cutting of paver block

necessary then it should be cut by machine only and carting.

The finished surface of the paver block shall have resonably

good, plain finished. Paver blocks shall be compacted and

shall be relaid if necessary. Gravel or such type of materials

shall not be allowed for production. Laying on 5 cms thick sand

Provoding and fixing flush door shutters, solid core

construction with frame of first class hard wood with cross

board and face veneer or ply wood face panels, including

anodised alluminium butt hinges with necessary screws. (B)

176 2 Non- decorative type and block board core anodised 1779.97 Smt

alluminium butt hinges in flush door shutters (2) 35 mm thick.

Labour work for fixing any kind of paving with cement pointing

in CM 1:2, including watering, ramming etc comp. as dir.For

I) Laying on Sand bedding as per requirement to fix the

177 2 C.C.Block / Nibhada Stone in Line & Level

Box type metal letters forming composite box made from 1mm

thick stainless steel plate of grade 304 having brush finish of

178 following font size to be fixed at Main Gate in english and or

Gujrati and including fixing charges approved before fixing by

clent / consultant.

A 2 400mm high 1,000.00 Nos.

B 2 300 mm high 750 Nos.

C 2 230 mm high 565 Nos.

Providing and fixing false ceiling at all height including

providing and fixing of frame work made of special sections,

power pressed from M.S. sheets and galvanized with zinc

coating of 120 gms/sqm (both side inclusive) as per IS :

and consisting of angle cleats of size 25 mm wide x 1.6 mm

thick with flanges of 27 mm and 37mm, at 1200 mm centre to

centre, one flange fixed to the ceiling with dash fastener

mm dia x 50mm long with 6mm dia bolts, other flange of cleat

fixed to the angle hangers of 25x10x0.50 mm of required

length with nuts & bolts of required size and other end of angle

hanger fixed with intermediate G.I. channels 45x15x0.9 mm

running at the spacing of 1200 mm centre to centre, to which

the ceiling section 0.5 mm thick bottom wedge of 80 mm with

tapered flanges of 26 mm each having lips of 10.5 mm, at

mm centre to centre, shall be fixed in a direction perpendicular

to G.I. intermediate channel with connecting clips made out of

2.64 mm dia x 230 mm long G.I. wire at every junction,

179 2 Engineer incharge, manufacture’s specification and

Providing & Fixing SPEED BUMP - #2 No (1 black, 1 yellow)

350 x 500 x 50 mm, Size per color End Cape 350 MM x

MM x 50 MM TOP DESIGN - Lining Top flat ANTI SKID

PATTERN FOR GRIP COLOUR :- YELLOW & BLACK BODY

MATERIAL :- MODIFIED THERMOPLASTICS (Polymer

180 2 Rubberized ) • ECO FRIENDLY RECYCLE RUBBER

Packing :- 4 pcs/ woven Bag Load Capacity :- 20 MT Fitting (

Fixing on TRAKE) :-4 holes & END CAPE :- 2 HOLE HEX Bolts

with Washer Epoxy for Bolt Fitting etc. complete as directed

Providing and fixing of Roller blind curtain/blackout. The fabric

shall be woven from formulated platisol extruded over a

polyaster yarn.The fabric shouldl be weaved to provide subtle

181 2 view of the side of the blind and should offer elimination of

glare and sunlight radiance upto a minimum of 80%.The fabric

shall be flame retardant.

Providing and fixing PVC/Gpsysum plain colour false ceiling

with grid type with aluminium frame from gypsteel,

fastners ,props, Finishing as per architectural drawing

182 2 allowing openings for A.C. Diffusers, Light/Electrical 933 Smt

Points etc –complete, Prior to fixing on frame.(Brand :

Anutone or equivalent ) (N.S.) or as directd by engineer In

Provdg. & laying S.W. Gully trap with brick masonry chamber &

183 2 water tight G.T.Stone including fixing of covervSquare mouth 1,263.15 No.

trap 100 mm x100 mm size P-Trap

Providing cement vata (10cmx10cmsize) quarter roundin

184 2 cement mortar 1:1 including neat cement finishing, waterin 23.45 Rmt.

getc. complete.

Providing and laying (to level or slopes) and jointing with stiff

mixture of Cement Mortar in proportion 1:1 Salt glazed

stoneware pipes including testing of pipes and joints

complete.(A) 100mm dia.

Providing and laying (to level or slopes) and jointing with stiff

mixture of Cement Mortar in proportion 1:1 Salt glazed

stoneware pipes including testing of pipes and joints

complete.(B) 150mm dia.

Constructing brick masonry chamber for underground C.I.

Inspection chamber and bends with bricks having crushing

strength not less than 35Kg/Cm2 in C.M. 1:5 C.I. cover with

frame (Light duty) 455mm x 610mm intenal dimensions total

weight of cover with frame to be not less than 38Kg. (Wt. of

cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with

1:2:4 mix (1-cement :2- coarse sand :4-graded stone

aggregate 20mm size) foundation concrete 1:5:10 inside

plaster 15mm thick with cement mortar 1:3 finished smooth

with a floating coat of neat cement on walls and bed concrete

etc. complete.(i) Inside dimensions 455mmx 610mm and

450mm deep for single pipe line.

Constructing brick masonry chamber for underground C.I.

Inspection chamber and bends with bricks having crushing

strength not less than 35Kg/Cm2 in C.M. 1:5 C.I. cover with

frame (Light duty) 455mm x 610mm intenal dimensions total

weight of cover with frame to be not less than 38Kg. (Wt. of

cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with

1:2:4 mix (1-cement :2- coarse sand :4-graded stone

aggregate 20mm size) foundation concrete 1:5:10 inside

plaster 15mm thick with cement mortar 1:3 finished smooth

with a floating coat of neat cement on walls and bed concrete

etc. complete.(i)Inside dimensions 500mm x 700 mm and

450mm deep for pipe line with one or two inlets.

Providing, supplying and fixing precast C.C. blocks (M-20)

edge kerb having size of 75 x 300 x 300 mm depth and as per

189 2 design conveying it to the site, jointing into C:M 1:3 and 219 Rmt.

racking out the joints incl. necessary excavation of asphalt, soil

etc..completed.

Constructing a cooking Sandwich platform 60 cm. width and

cm high resting on B.B.Masonry walls 23 cm.thick in C.M.(1:6)

190 8 with (ii) Fixing black Granitee 30mm thick laid on precast 754.95 Rmt.

R.C.C. (1:2:4) slab with plastering on exposed faces of wall in

C.M. (1:4) etc complete

Providing and fixing hard drawn steel wire fabric 75mm x

191 8 25mm mesh or weight not less than 7.75 kg. per Sq.M. to 754.65 Smt

window frames etc. including60 x 20mm beading of teak wood.

Providing & fixing 15 cm wide chicken mesh jali with nails &

192 8 then application of 15 mm plaster on R.C.C.& masonary joints 35 Rmt.

as per dir.of engg.in charge

Providing and laying cement concrete flooring 1:2:4 (1-cement

: 2-coarse sand : 4-graded stone aggregate 20mm nominal

193 8 size) laid in one layer and finished with a floating coat of neat

cement. (A) 50mm thick.

Providing and constructing, Underground (U/G) water tank of

specified capacity, on specified location, for all depths, in

controlled CC of M-200 grade with bottom slab, top slab and

RCC walls, including cost of form work and reinforcement, with

inside and outside plaster in CM 1 :3 and water proofing

194 5 treatment as per IWP specification, including injection,

grouting, etc. complete. The rate includes for providing and

fixing two nos. 0.6m. x 0.6 m. size medium duty CI manhole

cover/s at top, including wash out pipe line and inlet and outlet

connections etc. complete.

Providing and fixing PVC Printed pain colour false ceiling with

grid type with alluminium frame consisting of 600mm x 600mm

3mm thick plain PVC sheet used as panel insert in a frame

work made using anodized alluminium T section of size 1 x

(235 x 25mm, 19 gauge or 1 mm thick) in square pattern of

grid sizes of 2 x 2 (600 x 600mm) The alluminium frame work is

195 5 supported from the cceiling with the help of G.I. hook and G.I.

wire/6mm M.S. rods of required sizes to maintain proper level

etc. The aluminium frame work is supported on side wall with

the use of alluminium L section of size 1 x1 (25 x 25mm)

angles etc. complete as per direction of Engineer in charge.

Manufactures specification and drawing.

Providing and supplying of labour for necessary manual

excavation, cleaning, Shifting of Material Or any other, or for

196 5 any other work as directed by Engineer In charge. The Rate

includes Handcart with Mazdoor

A 5 Mukadam/supervisior/karigar 425 No

B 5 Fitter/Plumber/Mason 697 No

C 5 WELDER/ Gas cutter at Day /night 689 No

Supplting of welding machine / gas cutter including cost of

D 5 welding rods/gas, Transportation, including carting from site to 1500 No

E 5 Mazdoor at Day Female 450 No's

E 5 Mazdoor at Day Male 493 No's

Supplying electric breaker machine for RCC slab or asphalt

demolishing work on site by using operator, fuel, power supply

etc.complete as directed. (no payment should be allowed for

197 5 non working condition of machinery and for pipe line

excavation and M.H. work. Allowed only for break down work)

(Based on Previously approved rate by CE sir )

Providing and fixing concealed center point to wall ceiling &

floor CPVC (SDR 13.5) PIPE having National Sanitation

198 Foundation (NSF) seal for potable water of following dia.

Nominal bore tube fittings and clamps including making good

the wall, ceiling and floor etc. complete.

A 2 15 MM DIA 165.21 Rmt

B 2 20 MM DIA 202.97 Rmt

C 2 25 MM DIA 247.25 Rmt

D 2 32 MM DIA 330.36 Rmt

E 2 40 MM DIA 437.66 Rmt

199 2 50 MM DIA 647.3 Rmt

Supplying and fixing C.I. cover 300mm x 300mm without frame

200 2 for Gulley trap (Standard pattern) te weight of cover to be not 491.8 Each

Providing and fixing to wall ceiling and floor 10.0Kg.F/Cm2

working pressure polythene pipes of the following out side Dia

201 Low densidy, complete with special falnge compression type

fittings, wall clips etc. including making good the wall ceiling

Filling available excavated earth(excluding rock) in trenches.

plinth, sides of foundations etc. in layers not exceeding 20 cm.

202 2 in depth consolidating each disposited layer by ramming and

Filling in plinth with sand under floors including watering

203 2 ramming, consolidating and dressing complete

Filling in foundation and plinth with murrum or selected soil in

204 15 layers of 20cm. thickness including watering, ramming and 286.2 cumt

consolidating etc. complete

Filling in Sunken Portion with good Quality Aerated light weight

concrete block having crushing strength not less than

kg/sqcm and where directed by the Architect / Engineer-

205 2 incharge, in sunk in layer. including watering, ramming where it

is required etc. complete, as directed by the Architect /

Engineer-in-charge .

Providing and applying fibre reinforced elastomeric liquid water

proofing membrane with resilient acrylic polymers having Sun

Reflectivity Index (SRI) of 105 on top of concrete roof in three

coats @10.76 litre/ 10 sqm. One coat of self-priming of

elastomeric waterproofing liquid (dilution with water in the ratio

206 1 of 3:1) and two coats of undiluted elastomeric waterproofing 562.4 sq mt

liquid (dry film thickness of complete application/system not

less than 500 microns). The operation shall be carried out after

scrapping and properly cleaning the surface to remove loose

particles with wire brushes, complete in all respect as per the

direction of Engineer-in- Charge.

Providing and laying integral cement based water proofing

treatment including preparation of surface as required for

207 1.392 treatment of roofs, balconies, terraces etc consisting of 1150.48 sq mt

following operations:

(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of

cement admixed with water proofing compound conforming to

IS. 2645 and approved by Engineer-in-charge over the RCC

slab including adjoining walls upto 300 mm height including

cleaning the surface before treatment.

(b) Laying brick bats with mortar using broken bricks/brick bats

25 mm to 115 mm size with 50% of cement mortar 1:5 (1

cement : 5 coarse sand) admixed with water proofing

compound conforming to IS : 2645 and approved by Engineer-

in-charge over 20 mm thick layer of cement mortar of mix 1:5

(1 cement :5 coarse sand ) admixed with water proofing

compound conforming to IS : 2645 and approved by Engineer-

in-charge to required slope and treating similarly the adjoining

walls upto 300 mm height including rounding of junctions of

walls and slabs.

(c) After two days of proper curing applying a second coat of

cement slurry using 2.75 kg/ sqm of cement admixed with

water proofing compound conforming to IS : 2645 and

approved by Engineerin- charge.

(d) Finishing the surface with 20 mm thick jointless cement

mortar of mix 1:4 (1 cement :4 coarse sand) admixed with

water proofing compound conforming to IS : 2645 and

approved by Engineerin- charge

(e) The whole terrace so finished shall be flooded with water for

a minimum period of two weeks for curing and for final test.“All

above operations to be done in order and as directed and

specified by the Engineer-in-Charge :and shall be guaranteed

for minimum period of 10 years after handing over the

completed building by the main contractor to be finished as

directed. Stamp paper guarantee 10 years to be furnished

before receiving any payment from the client.

With average thickness of 120 mm and minimum thickness at

khurra as 65 mm.

Rapairing of Auditorium Chair . It Including material charges

208 25.00 and Labour Charges For Erection And Fixing Spring for smooth 523.00 No

and easy pushback system.

Supply and Fixing of Auditorium seating Fabricate Auditorium

seating with Synchronized Push back Chair with Ergonomically

designed Poly Urethane foam for seat and back made my

DOW chemical with High Pressure moulding technology to

achieve long life performance, upholstered with stitched

Layer 100% Yarn Dyed fabric Upholsteries. Chair profile with

the seat in Normal position and without a tablet arm should not

be more than 75 cm. Chair pushback mechanism should

consist of 2 nos. x DIA 50 mm ZYTEL Based Rollers which is

supported by AXIAL shaft of DIA 12 mm is Driven by radial

movement of 4 set of Swing Arms of size 25mm x 6 mm

thickness with Orbital Riveted Solid Dia 8 mm Barrel MS

Rivets. The pushback movement is achieved by synchronised

movement of 04 links mounted on Two Number of triangular

209 1.00 Symmetrical housing of size 27 cm x 23 cm duly embossed for 9990.00 No

extra strength by 1.2 cm made up by 0.12 cm CRCA

compliance to IS 513. The entire mechanism should be made

in India and should have total weight 8.5 kg duly including

fixing perimeter channels 0.5 mm thick 27 mm high having

flanges of 20 mm and 30 mm long, the perimeter of ceiling

fixed to wall/partition with the help of rawl plugs at 450 mm

centre, with 25mm long dry wall screws @ 230 mm interval,

including fixing of gypsum board to ceiling section and

perimeter channel with the help of dry wall screws of size 3.5 x

25 mm at 230 mm c/c, including jointing

Painting the kids picture chart & letter writting of

210 10.00 different size and shapes as per details/design etc.comp. 5803.57 wall

as dire.by engineer in charge