ADDN/ALTN INCLUDING REPAIRS TO OFFICERS MD ACCN

Amount

Taking down cement plaster any description, on brick or stone walls, etc. including raking out joints, hacking for key & scrubbing down with water, etc. & removing rubbish off the premises, complete all as specified & directed.

Dismantling of cement concrete tiles in floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness below or above ground level incl removal of demolished material exc 1.5 km but not exc 5 km complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete in any description and in any position, not otherwise specifically provided for incl removal of demolished material exc 1.5 km but not exc 5 km complete all as specified and directed.

Demolition of cement concrete (un-reinforced) to roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work not exceeding 15 cm thickness incl removal of demolished material exc 1.5 km but not exc 5 km complete all as specified and directed.

Demolition of reinforced cement concrete reinforced roofs, floors (Other than ground floors), beams, staircases, landing, chajjas, slab & similar suspended work incl removal of demolished material exc 1.5 km but not exc 5 km complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles and removal all rubbish material outside of MD Land complete all as specified and directed.

Dismantling of 75mm bore cast iron drain pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed. Note :- The length shall be measured along the centre line including fittings and accessories).

Dismantling of 100mm bore cast iron drain pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed. Note :- The length shall be measured along the centre line including fittings and accessories).

Taking up or down 15mm bore steel tubing and connections removal complete all as specified and directed.

Taking up or down 20 mm bore steel tubing and connections removal complete all as specified and directed by Engr-in-Charge.

Taking up or down 25 mm bore steel tubing and connections removal complete all as specified and directed by Engr-in-Charge.

Demolition of PVC/RCC Water tank up to cap 500 Lts & removal of all retrieved material complete all as specified & directed.

Demolition of PVC/RCC Water tank cap exc 500lts but n.exc 1000 Lts & removal of all retrieved material complete all as specified & directed.

Taking down existing water proofing roof treatment of all description and scrapping and properly cleaning of the surface to remove loose particles with wire brushes complete all as specified and directed by Engr-in-Charge

Taking down existing water proofing treatment for sunken slab incl removal of all filling materials around WC upto top of existing sunken slab complete all as specified and directed by Engr-in-Charge

Taking down chowkats or frames not exceeding 1.5 Sqm each with shutter (without taking off shutter from the frame) including iron mongry and removing from site complete all as specified and directed.

Taking down chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutter (without taking off shutter from the frame) including iron mongry and removing from site complete all as specified and directed.

Taking down shutter of any description exc. 1 sqm but n.exc 2 sqm each including iron mongry and removing from site complete all as specified and directed. .

Taking down and re-fixing after easining to shutters of any description exceeding 1 sqm but n.exceeding 2 sqm each in the same opening complete all as specified & directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified & directed.

Demolition of stone slabs / PCC tiles of any description or thickness in floors, aprons laid bedded and pointed in any mortor etc incl removal of demolished material complete all as specified and directed.

Raking out joints/pointing to random rubble or polygonal rubble uncoursed or brought up to courses complete all as specified & directed.

M&LCutting holes in stone masonry walls in cement mortar for inserting holdfasts & making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified & directed.

M&L for re-inforced cement concrete (nominal mix) type B1 (1:2:4) using 20 mm graded stone aggregate in columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for re-inforced cement concrete (nominal mix) type B1 (1:2:4) using 20 mm graded stone aggregate in chajjas complete all as specified and directed.

M &L 10mm dia and over mild steel TMT bars cut to length, bent to shape as required including cranking ,hooking ends & binding with mild steel wire (annealed) not less than 0.90mm dia complete all as specified and directed.

M &L 5mm dia and over upto 10mm dia mild steel TMT , cut to length ,bent to shape required including cranking and binding with and including mild steel wire (annealed) not less than 0.90mm dia as in stirrups, spacers and binders etc complete all as specified & directed.

M & L for form work to sides of square/rectengular pillars, columns, posts, struts etc for fair finished concrete surface complete all as specified and directed.

M & L for form work to soffits of suspended slabs such as roof slabs,landings, chajjas n. exc. 20cm thick (horizontal or sloping for fair finished concrete surface complete all as specified and directed.

Demolition of loose concrete cover of RCC columns, beams, slabs, chajjas and the like as directed, roughening and cleaning concrete surfaces with steel wire brushes, washed with water and allowed to dry, including dusting of steel reinforcement, providing fabric mild steel wire mesh 75X75mm of 2mm dia as reinforcement to concrete surfaces, applying adhesive/admixture over steel mesh and providing ordinary portland cement 53 grade and 2 parts of banas sand mixed with adhesive/admixture at the rate as per manufactures instruction or 2% by wt of cement all as directed with a pressure of 2 to 2.5 kgs per sqm by guniting machine including necessary padding, steel scaffolding and shuttering for working platform/formwork , patchwork exc 2.5 sqm each etc complete all as specified and directed.

Dittto all as per item 31 above but patch work of area nexc 2.5 sqm each complete all as specified & directed.

M & L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) straight or curved on plan exc 6 mtr mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L Providing, cement concrete Type B1 1:2:4 (20 mm graded aggregate,on lintels up to 1.5m clear span, bed plates,coping, kerbs water trough & the like including weathering, slightly rounded or chamfered angles & throating, complete all as specified & directed.

S & F 35mm thick factory made IInd Class Hard wood (Hollock) plain framed, panelled door shutters single panel with lock rail and panel of 9mm B.W.P. marine grade plywood bonded with high quality liquid phenol formaldehyde synthetic resin adhesive conforming to IS-710 or 12mm thick particle board veneered with commercial veneering on both faces. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed.

S & F 35mm thick factory made glazed and skeleton door shutters open rebated of second class hard wood rail and styles(Hollock), prepared to receive glass/gauge etc without sash bars, edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass/gauge etc. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed. Note :- S & F Glass/wire gauge shall be measured and paid for separately

S & F for Factory made Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing as applicable to item 08095 given in SSR Part – II (2010) complete all as specified and directed.

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppy and fixing in the frame at site complete all as per specifications and drawings as applicable to item 08080 given in SSR Part – II complete all as specified & directed.

S&F 1.00 mm thk pressed steel shutter with frame for cup board incl 3.15 mm thick steel hings 100 mm long(3 Nos for each shutter), standard rim latch with12 mm dia rod for locking, 12 mm dia fastner (3 Nos each side) of size as reqd at site incl frame complete all as per Drg No- TD/2009/105(R) sheet No 1/1

S&F 3 Track powder coated aluminium window with std aluminium section as per TD with 2 Nos glazed shutter and 1 No Wire mesh shutter complete including 5mm thick glass pane, 0.36mm dia stainless steel wire mesh avg width of aperature 1.4 mm including rubber gasket, glazing clips, aluminium cleats, locking arrangement complete all specified and directed. (Drg No TD/CEJZ/2004/65R Sh 1/1

S&F Anodised aluminium Powder coated frame for windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified & directed.

S & F Anodised aluminium powder coated window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.), hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified & directed.

S & F 4mm dia aluminium ornamental type powder coated grill with fixing channel complete all as specified & directed.

S & F for factory made steel windows conforming to IS-1038 with side hung shutters including box type hinges with 2 Nos MS 100mm size tower bolt over MS flat iron for each openable leaf & Z section handle and steel peg stay complete with glazing bars, dovetailed or welded including one shop coat of Red Oxide Zinc chromate primer complete all as specified and directed. Note :- (i) Window size and pattern wherever required and directed shall be suitable for installing Desert cooler. (ii) Glass shall be measured and paid for separately).

S & F for factory made steel windows conforming to IS-1038 with side hung shutters including box type hinges with 2 Nos MS 100mm size tower bolt over MS flat iron for each openable leaf & Z section handle and steel peg stay complete without glazing bars, dovetailed or welded including one shop coat of Red Oxide Zinc chromate primer complete all as specified and directed. Note :- (i) Window size and pattern wherever required and directed shall be suitable for installing Desert cooler. (ii) Wire mesh shall be measured and paid for separately).

S&F factory made steel ventilator with top hung shutter including hinges, steel peg stay complete all as specified and directed.

S & F factory made steel ventilator with fixed type shutter without glazing bars including hinges, steel peg stay, complete all as specified and directed.

Welding in repairs thickness of metal to be welded not exc 6mm and lenth of welding exc 2.5cm but n exc 5cm complete all as specified & directed.

S&F 4mm thick sheet glass ordinary quality exc 0.7 sqm each pane complete all as specified & directed.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire & average width of aperture 1.40mm & fixed with alluminium wire staples complete all as specified & directed.

S&F in repairs Stainless steel wire cloth, 0.36mm nominal dia of wire & average width of aperture 1.40mm & fixed to wodden door shutters complete all as specified & directed.

S & F 250 mm long Aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded section & fixing blots & sliding bolts of extruded section or cast aluminium alloy & fixed complete all as specified & directed.

S & F MS butt hinges 100mm size cold rolled medium weight and fixed complete all as specified & directed.

S & F MS butt hinges 50 mm size cold rolled medium weight and fixed complete all as specified & directed.

S & F 100 mm size Butt hinges, extruded aluminium alloy with galvanished mild steel hinges pin, anodized & fixed, type B-21 complete all as specified & directed.

S & F Aluminium handles cast moulded type 100mm size fixed with screws complete all as specified & directed.

S & F Aluminium handles cast moulded type 150mm size fixed with screws complete all as specified & directed.

S & F Aluminium anodised barrel tower bolts of extruded section, 200mm long complete all as specified & directed.

S & F second class hardwood small fittings such as door and window stops and the like n.exceeding 200 cucm each fixed complete all as specified & directed.

S & F in repair Floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring.(140mm Long) complete all as specified & directed.

S & F Helical door spring 300mm size including roller and roller plate complete all as specified & directed.

S & F 125mm size hasp and staple aluminium anodised safty type including bolt to hinge plate and fixed complete all as specified & directed.

S & F in repair second class hard wood plain, solid, straight frames wrought, framed rabated on the solid, rounded or chamfered, put together with glue pinned at joints and fixed with long MS screws including two coats of polishing etc complete all as directed and specified.

M & L 18-19 mm thick Pre-laminated particle boards, interior grade perlaminated one side with decorative choice lamination & other side balancing white lamination fixed with screws to timber frame work complete all as specified & directed by Egnr-in-Charge.

S & F stainless steel, Continuous (piano) hinges, bright finished 40mm width of flaps for cup board shutters complete all as specified & directed.

S & F Ball catches with 8mm dia steelball, and brass body and striking plate including letting in and fixed complete all as specified & directed.

S&F in repair 25 mm dia drapery rod fancy type with bracket & 8 rings per window /door , side holders ,projecting type clamp etc with necessary all fittings complete all as specified & directed.

M & L Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and fastening and fixing complete FE 290 Gde E-165 complete all as specified & directed.

M & L Framed work such as grills, gratings, etc., with ends of bar shoulder &/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks with Angle, MS sheet Flat iron & similar work conforming to Fe 290 GDE -E-165 complete all as specified & directed.

M & L Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161-1979 grade St.-240 complete all as specified & directed.

S&F pre painted galvalume aluminium zink coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws and washers complete all as specified & directed.

S & F 40 mm medium grade GI pipe, ,60cm long out of which 20cm projected outside for spout pipe, placed in slope to drain water accumulated in sunken portion incl making good in CM 1:3 for the damaged portion complete all as specified & directed.

M & L for WPT in sunken floors as described here under:- Sunken floor and sides up to finished floor level shall be plastered with 15 mm thick cement plaster in CM 1:4 mixed with water proofing liquid @ 150 ml per bag of cement . (ii) Preparing plastered surfaces and providing APP polymeric water proofing membrane , minimum 3 mm thick and weighing not less than 3.0 kg/ sqm of make super thermolay manufactured by STP ltd or Hyper Plas (Polyster) manufactured by M/S IWL Ltd or 'Shatiplas' (Polyster) manufactured by M/S Capital Steels and chemicals Pvt Ltd as approved by GE, black finish reinforced with non-woven polyster matt, with a thermo fusable finish laid over compatible bitumen primer (Bitumen primer shall be TANK MASTIC of M/S STP Ltd or EMW Flate' of M/S Texas India Ltd) at the rate of 0.40 Ltr/Sqm torching overlaps with a propane or a butane gas torch , with a over lap of 75mm at the sides and 100mm at the ends sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer's instructions including preparation of surface and filling lime concrete 1:5:10 type E2 with brick bats complete all as specified and directed. Note :- (i) Polymeric membrane shall be laid in sunken floor and on sides up to finished floor level. (ii) The waterproofing treatment shall be got carried out by the manufacturer or their authorised applicators. (iii) Above aspects are deemed to be included in quoted rate. (iv) Supply only water proofing liquid shall be measured and paid seperately (v) Slab area only will be measured for payment purpose.

M &L for PCC (1:2:4) type B-0 using 10/12.5 mm graded stone aggregrate laid over roof slab after applying cement slurry for filling undulationations finished even and smooth without using extra cement complete all as specified & directed. (Note : cement slurry shall be measured and paid separately)

M & L for applying cement slurry over existing roof surface @ 3 Kg/Sqm complete all as specified and directed.

M&L screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:4, over RCC roof slabs for laying water proofing treatment mixed with using water proofing liquid @ 150 ml per bag of cement complete all as specified and directed by Engineer-in-Charge.(Note : Water proofing liquid shall be measured and paid separately)

supply Integral water proofing Liquid of Dr fixit/sika/Fosroc complete all as specified & directed.

M&L Water proofing treatment on roof surfaces in the following manner : - (a) The surface shall be painted with hot paving bitumen grade Vg40 conforming to IS-73 @ 1.20 Kg/Sqm over a coat of bituminous primer conforming to IS-3384 applied @ 0.30 Ltr/Sqm. (b) Heavy duty polythene film (white) of 150 micron thickness weighing 135 gms/ Sqm (approx) having tensile strength not less than 140 Kg/Square metre in machine direction and 110 Kg/Sq cm in transverse direction, conforming to IS-2508 shall be laid with overlaps & bonded with cold cutback adhesive, overlaps being not less than 150 mm. Polythene film shall be tucked in parapet wall to a depth of 65 mm as per figure shown in IS-7290. (c) Brown craft paper of weight not less than 100 gms/Sqm laminated over the film with semi hot layer of paving bitumen grade Vg40 conforming to IS-73 @ 0.60 Kg/Sqm shall be painted on the paper, paper reversed and pasted on the film. (d) Semi hot paving bitumen grade Vg40 conforming to IS-73 applied @ 1.20 Kg/Sqm on the surface and the entire surface shall be dusted with fine sand. (e) 20 mm thick screed in CM 1:4 shall be obtained after fine sand dusting , when the cement mortar is still green 18-20mm thick marble crazy pirces shall be spread in regular panel using dividers or marble strips 18 to 20mm thick and 50mm wide. The size of panels shall be at 1 to 1.5 m intervals in length and breadth over the entire roof area, leaving joints 10 to 15 mm wide . The left out space shall be filled with cement, marble powder & marble aggregate of 4 to 7 mm size like as cast in situ terrazzo toping. The work of placing , curing and grinding shall be done all as per clause 13.38.4 to 13.38.6 of MES SSR Part-I (f) Covered fillet in PCC (1:2:4) type B-0 with terrazzo finishiong layer at top of radius 75mm shall be provided at the junction of roof and parapet wall/chimney/other vertical surface and surface painted with a hot paving bitumen grade Vg40, conforming to IS-73 @ 1.20 Kg per Square metre over a coat of bituminous primer conforming to IS-3384 applied @ 0.30 litre per square metre.

Supplying & applying fiber reinforced UV resistant elastomeric liquid applied waterproofing & heat reflective coating with acrylic polymers and polyester/ glass fibres after scrapping and properly cleaning the surface to remove loose particles with wire brushes , complete all as directed by Engineer-in-charge, over a coat of primer as per manufacturers instruction complete all as specified & directed. (Make Asain paint, M/STP LTD-Shalicry MHI, M/S Sika cool coat.

M&L 15mm thick rendering in cement mortar 1:4 to stone masonry wall surfaces or on other than fair faces of brick wall surfaces finished fair & even for fixing tiles etc complete all as specified and directed by Engineer - in - Charge.

M&L coloured Glazed ceramic tiles in verticle surface (350x250mmx7mm) /450x350x 7mm thick, as dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by Engineer-in-Charge.

M & L 25 mm thick PCC 1:2:4 type B-1, using 20 mm graded stone aggregate as in floors, surfaces finished fair and even complete all as specified and directed.

M&L screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:6, for laying floor finishes/tiles complete all as specified and directed.

M & L Vitrified ceramic double charge tile size n exc 1.0 sqm & 10 mm thick (square/rectangular) in floors etc., set & jointed in neat cement slurry & pointed in white or coloured cement to match complete all as specified & directed.

All as per Item No 84 here-in-before but on vertical surfaces complete all as specified & directed.

M&L Non- skid coloured ceramic tiles 300x300x7 to 8mm thick (square / rectangular) as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified and directed.

M&L for non skid joint free ceramic tiles 600x600x7 to 8mm thick (square / rectangular ) as in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match with coloured tiles complete all as specified and directed by Engineer-in-Charge.

All as per item 87 above but on vertical surfacess skirting etc set and jointed in neat cement slurry complete all as specified and directed by Engineer-in-Charge.

M&L for grinding/cutting old Kota stone surface rubbing and polishing with (bee wax polish) complete all as specified and directed.

'M&L machine cut kota stone flooring 20-22 mm thick (not less than 450x450 MM SIZE) as in floor laid over 15mm thick cement screed of CM (1:4) as in steps in single piece incl chipping the steps where required complete all as specified & directed.

All as per item No 90 above but in risers to steps, skirting over rendering in CM 1:4 complete all as specified & directed.

M&L 16-18mm thick Granite work (table rubbed & polished) in steps, jambs, pillars, window-cills cooking platforms & like in 15 mm screeding cement mortar (1:4) including pointing into white cement (1:2) using marble dust with admixture of pigment to match shade of granite complete all as specified & directed.

M&L for 100 mm thick Cement concrete type D-2, 1:4:8 (40mm graded aggregate) as in sub base complete all as specified & directed.

M &L Machine pressed precast concrete interlocking paver block with grey cement and pigments any shape and size confirming to IS 15658 -2006 of 80mm thick, M-40 Grade complete all as specified & directed.

M & L Sand filling under floors or in foundation including watering and consolidation complete all as specified & directed.

M & L for 75mm thick PCC 1:3:6 , type C-2 using 40 mm graded stone aggregate as in plinth protection laid in slope in 1:30 in alternative bays not exceeding 3 mtr in length. Exposed surfaces finished even and smooth without using extra cement including raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:3 complete all as specified and directed .

M&L rendering 15 mm thick in CM 1:6 on brick masonry surfaces or on other than fair faces of brick masonry finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L rendering 15 mm thick in CM 1:6 on stone masonry surfaces or on other than fair faces of brick masonry finished even and smooth witout using extra cement complete all as specified and directed.

M&L 15mm thick rendering in cement mortar 1:4 to stone masonry wall surfaces or on other than fair faces of brick masonary finished even and smooth without using extra cement mixed with Dr Fixit liquid water proofing compound @ 150ml per bag of cement over dubbing out cement plaster 5mm thick in CM 1:4 complete all as specified and directed. Note : liquid water proofing compund shall be measured and paid seperately.

M&L rendering 5 mm thick in CM 1:3 as on concerete surface on ceilings finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for preparing newly plastered surfaces and applying two coats of distemper with distemper oil emulsion white or tinted over and including one coat of 1mm thick wall care putty complete all as specified and directed. (Make : For wall putty- Birla white/Bison wall putty of Berger/Narolac wall putty/Asian paint powder putty /Acro wall guard.)

M&L for complete removal of existing treatment on walls, including cleaning of any mortar drops, fungus efflorescent salts etc and preparation of old plastered surfaces and applying two coats of distemper with distemper oil emulsion white or tinted over and including one coat of 1mm thick wall care putty complete all as specified and directed. (Make : For wall putty- Birla white/Bison wall putty of Berger/Narolac wall putty/Asian paint powder putty /Acro wall guard.)

M&L for preparation of newly plastered surfaces of wall and applying two coats of exterior emulsion paint over a coat of primer complete all as specified and directed. (make- Apex ultima of asian, weather shield max of ICI/Dulux)

M&L complete removal of existing treatment of old plastered surfaces of walls and washing, rubbing down and stopping of painted surfaces and applying two coats of exterior emulsion paint over a coat of primer complete all as specified and directed. (make- Apex ultima of asian, weather shield max of ICI/Dulux) IN CAMOUFLAGE PATTERN

M & L for preparation of old plastered surfaces of walls & applying two coats of white wash complete all as specified & directed.

M & L for preparation of newly plastered surfaces & applying three coats of white wash on ceilings complete all as specified & directed.

M & L for preparation of old plastrered surfaces of ceiling & applying one coats of white wash complete all as specified & directed.

M&L preparation new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide zinc chrome primer complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new or previously untreated wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over and including one coat of pink primer complete all as specified and directed by Engineer-in-Charge.

M&L preparation old untreated steel surfaces of any description over 10 cm width or girth and applying one coats of synthetic enamel paint over complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old painted wooden or wood based surfaces of any description n.exc 10 cm in width or girth when unconnected with other painting or when painted in a diferent tint and applying one coat of synthetic enamel paint over complete all as specified and directed.

Cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landing, steps, cill, sunshades, shelves, lintal etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exc 10 cm girth in brick wall/stone masonry wall etc complete all as specified & directed.

S& F Cast iron cowls for 100 mm bore complete all as specified and directed.

S&F Cast iron 75 mm dia of outlet floor trap with grating including jointing to waste pipe fixed in cement concrete type B 1(1:2:4) complete all as specified & directed.

S&F Cast iron 75 mm bore soil, waste & vent pipes, in any length with or without ears, with lead joint fixed to walls complete all as specified & directed.(Make -NECO/KESORAM/SKM)

S&F Cast iron 75 mm bore soil, waste & vent pipes, in any length with or without ears, with lead joints, laid in floors complete all as specified & directed.(Make -NECO/KESORAM/SKM)

S&F Cast iron 100 mm bore soil, waste & vent pipes, in any length with or without ears, with lead joint fixed to walls complete all as specified & directed. (Make -NECO/KESORAM/SKM)

S&F 75 mm bore bends (any radius), diminishing pieces or tapers (large bore measured) with oval excess door complete all as specified and directed.

S&F 75 mm bore branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval excess door complete all as specified and directed.

S&F 100 mm bore branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval excess door complete all as specified and directed.

S&F 100mm cast iron sanitary connection socket to fit WC out-let complete all as specified & directed.

Refixing of 100mm bore CI pipe obtain from item no 09 after cleaning in any length with or without ears, with lead joints fixed on walls complete all as specified & directed.

Refixing of 75mm bore CI pipe obtain from item no 08 after cleaning in any length with or without ears, with lead joints fixed on walls complete all as specified & directed.

S& F Salt glazed stoneware gully traps of size 150mmx150mm , square or round mouthed, type‘P’ complete all as specified & directed.

S & F Stack clamps out of 50mm by 5mm flat iron & 16mm dia round iron stays, including bolts & nuts & securing ends of stay to wall or roof for 75 mm bore pipe complete all as specified & directed.

S & F Stack clamps out of 50mm by 5mm flat iron & 16mm dia round iron stays, including bolts & nuts & securing ends of stay to wall or roof for 100 mm bore pipe complete all as specified & directed.

Fixing only 15 mm dia steel water tubing galvanized medium grade concealed in all type wall with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge (GI Tubing shall be issued under sch 'B' on payment)

Fixing only 20 mm dia steel water tubing, galvanized, medium gradeconcealed in all type wall with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge (GI Tubing shall be issued under sch 'B' on payment)

Fixing only 25 mm dia steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge (GI Tubing shall be issued under sch 'B' on payment)

Fixing only after cleaning 15 mm dia steel water tubing galvanized medium grade obtain from item no 10 above concealed in all type wall with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge

Fixing only after cleaning 20 mm dia steel water tubing, galvanized, medium grade obtain from item no 11 above concealed in all type wall with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge

Fixing only after cleaning 25 mm dia steel water tubing, galvanized, medium grade obtain from item no 12 above concealed in all type wall with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge

S&F in repairs vitreous china wash basin ivory flat back size 550 x400 mm including one No PVC waste pipe 25 mm dia and 75 cm long with 32 mm dia connector, 32mm size waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange end, bedded in red lead cement and other fixed complete including cutting for and pinning in ends of bracket or erecting stand complete all as specified and directed. (Make - CERA/PRAYAG/PERRYWARE, CAT PART NO-4642)

Cutting holes into or through stone masonry walls built in cement mortar or cement lime mortar and making good in CM 1:3 or walls of cement concrete 1:2:4 Type B-1 as required for Superficial area exc 150 sq.cm but n exc.400 sq.cm complete all as specified & directed.

All as per item no 134 above but Superficial area n exc 150 sq cm complete all as specified & directed.

S & F white Vitreous china wash down Wall mounted water closet pan with superior quality water jet spray and health faucet including plastic water closet seat white/black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device including flush pipe and fixing bolts including taking out old EWC and flushing cistern etc complete all as specified and directed. (Make - CERA/HINDWARE/PERRYWARE)

S&Fin repairs vitrous china squatting pan orrisa pattern, size 580x440 white with integral foot rests or out going pipe and to flushing pipe, antisyphonage pipe etcplastic water seat white/black pattern flat bottom and cover and mild steel chroumium plated complete all as specified & directed. (Make - CERA/HINDWARE/PERRYWARE)

S&F in repairs, PVC low level cistern 10 litres capacity, valve less, symphonic action type with float, handle including 32mm dia PVC flush pipe of polyethylene of low or high density & bracket incl taking down of old EWC with flushing cistern etc complete all as specified and directed . (Make - cera commander champion)

S&F in repair Brass chromium plated shower rose 100mm size with or without swivel joints, any size, including fixint to steel pipe or union complete all as specified and directed. (Make - JAQUAR/MARC/ESS-ESS)

S & F in repair 15 mm dia Angle valve, cast copper alloy chromium plated , screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions & fixed complete all as specified & directed. (Make - JAQUAR/MARC/ESS-ESS)

All as per Item No 140 here-in-before but Two way Angle cock 15 mm bore complete all as specified & directed. (Cat part No- MQT-526AF, Make-Jaquar)

S&F in repairs 15mm bore PVC connections, with PTMT nuts of length 450mm complete all as specified and directed.

S&F in repair 15 mm dia stop valve (conncelaed type) fancy type, chromium plated with long shank and cup for iron pipe or for unions and fixed complete all as specified & directed. (Make - JAQUAR/MARC/ESS-ESS)

S&F in repair 15mm bore stop valve cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and directed. (Make - JAQUAR/MARC/ESS-ESS)

S&F in repair 20mm bore stop valve cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and directed. (Make - JAQUAR/MARC/ESS-ESS)

S&F in repair 25mm bore stop valve cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and directed. (Make - JAQUAR/MARC/ESS-ESS)

S&F in repair bib taps 15mm bore cast coper alloy fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for union complete all as specified and directed. (Make - JAQUAR & EQUIVALANT) Cat part No- DRC-37037,

S&Fin repair brass chromium plated towel rail 20 mm dia, D type 60 cm long complete all as specified and directed. (Make - JAQUAR & EQUIVALANT) Cat part No- ACN-1111NM )

S&F in repair Towel ring of PTMT & including Chromium plated brass screws & wooden / plastic cleats (Minimum weight 90gms) complete all as specified and directed. (Make - JAQUAR/MARC/ESS-ESS)

S&F in repair Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed. (Make - JAQUAR & EQUIVALANT) Cat part No- A2N-7731 )

S & F in repair Toilet paper holder CP complete all as specified and directed. (Make - JAQUAR & EQUIVALANT) Cat part No- AKP-35751P )

S & F in repairs, PTMT alloy bathroom cabinet with mirror of overall size 350 x 450mm complete all as specified and directed. (Make Prayag or equivalent model of other makes as approved by Garrison Engineer)

S&F 500 litres, rotational moulded polyethylene 5 layered thermal insulated water storage tank (ISI marked) white colour (Cylindrical vertical with closed top), hoisted and fixed in position complete all as specified and directed by Engineer-in-Charge.

S&F 1000 litres, rotational moulded polyethylene 5 layered thermal insulated water storage tank (ISI marked) white colour (Cylindrical vertical with closed top), hoisted and fixed in position complete all as specified and directed by Engineer-in-Charge.

M & L Providing, cement concrete PCC 1:2:4 type B-1, using 20 mm graded stone aggregate as in roof kerbs or mud stops, rounded or chamfered on edges, plateform for service tank, surfaces finished fair and even complete all as specified and directed.

S&F 20mm bore ball brass valve high pressure with polythene float and fly nut complete, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engineer-in-Charge.

S & F in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420 mm bowl size 410 mm x 330 mm x 160 mm fixed in granite stone slab and top of granite stone match with top of kitchen sink complete all as specified & directed. (Note : granite shall be measured and paid in appropiate item)(Make - NIRALI/NEELKANTH/JAYNA)

S & F 4 way diverter for concealed fitting with built in non return valve with diverter handle complete including taking out of old wall mixer complete all as specified & directed. (Cat part No -DRC-37421, Make- jaquar)

S & F in repairs KITCHEN SINK mixer CP hot & cold, 15mm bore, bright finish with three joints screwed the ends for iron pipe and plugging complete all as specified and directed. (Make - JAQUAR & EQUIVALANT) Cat part No- APR-101309N)

S & F in repairs Basin mixture CP hot & cold, 15mm bore, bright finish screwed the ends for iron pipe complete all as specified and directed. (Make - JAQUAR & EQUIVALANT) Cat part No-MQT-516A )

S & F Plate rack of size 900mmx1200mmx200mm fabricated out of .6mm thick stainless steel sheet fixed in repair complete all as specified and directed. fixed in repair (Make - PRAYAG & EQUIVALENT, CAT PART-P336)

S & F mild steel chromium plated grating doom 100mm dia complete all as specified & directed.

S & F 300 mm Corner Glass shelf with ABS brackets complete all as specified & directed.

S&F PVC (SWR) 160mm bore pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S & F in repairs 17 mm thick modular membrane kitchen cabinet door shutter (made out by HDHMR boards) in wood grain colour, half round edge complete all as specified & directed.

S & F in repairs of kitchen basket stainless steel size 435mmx510mm including stainless steel guide channel complete all as specified & directed.

S & F in repairs auto close hinges , stainless steel , bright finish or electro galvanised fixed complete all as specified & directed.

S & F in repairs 17 mm thick HDHMR board in shelf and partition of kitchen cabinet complete all as specified & directed.

Excavation in post holes in soft/loose soil,each n. exc. 0.50 cum,getting out,returning,filling in and ramming earth or broken rubble mixed with earth around,in layers n. exc. 25 cm thick,watering and removing surplus excavated soil to a distance n. exc. 50 m and making good surfaces complete all as specified & directed.

M & L PCC 1:4:8 type D-2, using 40mm graded stone aggregate as in foundation filling and mass complete all as specified & directed.

M & L PCC 1:2:4 type B1, using 20mm graded stone aggregate as in foundation filling and mass complete all as specified & directed.

M&L for 100 mm thick Cement concrete type 1:2: 4 type B2 using 40mm graded aggregate as in floors finished even & smooth without using extra cement laid in alternate bays complete all as specified & directed.

Providing & injecting chemical emulsion for Post Constructional Anti-termite Treatment with external wall where the apron is not provided using chemical emulsion at the rate 7.5 liters per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavation channel along the wall and rodding etc. complete all as specified & directed.

Treatment of soil under existing floors using emulsion at the rate 1 liter per hole, 300mm apart including drilling & plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified & directed.

Taking down carefully point wiring and removing from site such as (Light,fan socket or power) Complete including fitting and fixtures,fan regulators switch boards,switches,ceiling rose, lamp holder etc from existing batten PVC conduit/steel conduit / PVC casing and capping wiring complete excluding light fittings and fans all as specified and making good to the disturbed surfaces to match all as specified and directed by Engr-in-Charge.

Taking down main Switches,MCB DB with MCBs complete all as specified and directed by Engr-in-Charge.

Taking down sub main wiring of any sizes all as specified and directed by Engr-in-Charge.

Taking down old tube light fitting/ bldg light/ street light fitting any type and removal from site and making good disturbed surfaces of walls, ceiling etc complete all as directed to match with existing surfacescomplete all as specified and directed.

Taking down Fan/ Geyser any type/make and removal from site and making good disturbed surfaces of walls, ceiling etc complete all as directed to match with existing surfaces all as specified and directed by Engr-in-Charge.

Material and labour for point wiring for light point/ ceiling fan point/ exhaust fan point controlled by one, one way switch complete with 1.5 sqmm FRLS insulated unsheathed 1100V grade copper multistranded conductor drawn through and including rigid PVC casing caping on ceiling/surface of the walls, roofs floors etc including 1.5 Sq mm FRLS insulated copper conductor as earth continuity conductor and connecting it to the common earth dolly all as specified and directed by Engineer-in-charge. Note:- Supply only of modular flush box including cover plate shall be measured and paid seperately. However, fixing cost of the same shall be deemed included in the unit rates of this item.

All as per item No 181 above but for one light point controlled by one two way switch. Note:- Supply only of modular flush box including cover plate shall be measured and paid seperately. However, fixing cost of the same shall be deemed included in the unit rates of this item.

All as per item No 181 above but for one 3 pin socket outlet 5 Amps on the same board with other switches complete all as specified and directed. Note:- Supply only of modular flush box including cover plate shall be measured and paid seperately. However, fixing cost of the same shall be deemed included in the unit rates of this item.

All asper item No 181 above but for one switch socket combination 5 Amps 3 Pin points on independent board complete all as specified and as directed. Note:- Supply only of modular flush box including cover plate shall be measured and paid seperately. However, fixing cost of the same shall be deemed included in the unit rates of this item.

All asper item No 181 above but for switch socket combination 15 Amps 5 Pins on independent board with 4 Sqmm PVC Insulated unsheathed,stranded copper, conductor cable (1100 V grade) complete all as specified and as directed. Note:- Supply only of modular flush box including cover plate shall be measured and paid seperately. However, fixing cost of the same shall be deemed included in the unit rates of this item.

Material and labour for wiring for one bell/buzzer point controlled by one push button with other switches or independent with cables 1.5 Sqmm size copper multistranded conductor drawn through and including rigid PVC casing caping on ceiling/surface of the walls, roofs floors as specified and directed by Engineer-in-charge. Note:- Supply only of modular flush box including cover plate shall be measured and paid seperately. However, fixing cost of the same shall be deemed included in the unit rates of this item.

M&L sub main wiring with 2 runs of 6 Sqmm cable multistranded copper conductor 1100 V grade drawn into and including suitable size PVC Casing caping with required accessories complete including 6.0 Sqmm copper conductor PVC insulated cable for earth continuity and connected to earth dully fixed on surface or walls/floor/roof etc complete all as specified and as directed.

M&L sub main wiring with 2 runs of 4 Sqmm cable multistranded copper conductor 1100 V grade drawn through and including rigid PVC casing caping with required accessories complete including 4.0 Sqmm copper conductor PVC insulated cable for earth continuity and connected to earth dully fixed on surface or walls/floor/roof etc complete all as specified and as directed.

M&L sub main wiring with 2 runs of 10 Sqmm cable multistranded copper conductor 1100 V grade drawn through and including rigid PVC casing caping with required accessories complete including 10.0 Sqmm copper conductor PVC insulated cable for earth continuity and connected to earth dully fixed on surface or walls/floor/roof etc complete all as specified and as directed.

S&F modular Switch one way 6 Amps, 1 module 240 V complete all as specified and as directed.

S&F modular Switch 2 way 6 Amps, 1 module 240 V complete all as specified and as directed.

S&F Modular Switch socket combination 3 pin 5 Amps 240 V flush type complete all as specified and as directed.

S&F modular socket 3 pin 5 Amps 240 V flush type complete all as specified and as directed.

S&F Modular Switch socket combination 3 pin 15 Amps 240 V flush type complete all as specified and as directed.

S&F PVC/Polycarbonate angular/batten type lamp holder with LED lamp 7 watt complete all as specified and directed.

Supply & fixing DECORATIVE WALL LIGHT FIXTURE MADE UP OF POLYCARBONATE AS PER Havells Model CITY 2 Code No LHDL06160099 incl 10 Watts LED bulb or equivalent complete all as specified and directed.

Supply & fixing ceiling rose surface type modular type, 65x50 mm, with 3 terminals complete all as specified and directed.

Supply & fixing Modular stepped type fan regulator 100 W complete all as specified & directed.

Supply and fixing wall mounted LED batten fitting (retrofit type including both fitting(patti) and rod), extruded aluminium heat sink for efficient heat dissipation with internal electronic driver, 20 watt complete all as specified and directed all as per havells cart part No LHLDEFXD5L8RO20 AND LHFXCEPITNNW020 or equivalent .

Supply and fixing wall mounted LED Mirror light batten fitting, extruded aluminium heat sink for efficient heat dissipation with internal electronic driver, 11 Watts complete all as specified and directed.

Supply and fixing LED building security light fitting 25 watts, pressure die cast aluminium housing with IP-66 deg of protection. complete with 32 mm dia GI Bracket of GI tubing light grade not less than 550 mm length, bent to shape of 120 degree angle alongwith clamps, bolts, Nuts etc complete all as specified and directed as per HPL cat part No HPLLEDSL2560S or equivalent.

Supply and fixing sheet metal enclosure for MCB DB double door TPN 4 ways 200 Amps rated bus bar complete all as specified and directed. Note :- (i) MCB shall be measured and paid seperately. (ii) MCBs and DBs shall be of same make.

Supply and fixing sheet metal enclosure for MCB DB double door SPN 04 ways 200 Amps rated bus bar complete all as specified and directed. Note :- (i) MCB shall be measured and paid seperately. (ii) MCBs and DBs shall be same make.

Supply and fixing sheet metal enclosure for MCB DB double door SPN 16 ways 200 Amps rated bus bar complete all as specified and directed. Note :- (i) MCB shall be measured and paid seperately. (ii) MCBs and DBs shall be same make.

Supply and fixing sheet metal enclosure for MCB DB double door SPN 12 ways 200 Amps rated bus bar complete all as specified and directed. Note :- (i) MCB shall be measured and paid seperately. (ii) MCBs and DBs shall be same make.

Supply and Fix of Bell push modular type 5 Amps complete all as specified and directed.

Supply and Fix of Electronic Call Bell 230 volts single pole A C complete all as specified and directed.

M&L MCBs suitable for lighting load, 50 Hz, 10 kA of under mentioned types and rating (to be housed in DBs) here in before including making all electrical connection with suitable size of copper lugs complete all as specified and directed.

MCB TPN 100 Amps 415 V

MCB SPN 40 Amps 240 V

MCB SP 06-32 Amps 240 V

MCB SPN 20 Amps 240 V

M&L for Earthing complete with galvanized steel earth plate electrode 60cmx60cmx 6.3mm thick buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 meter below normal ground level connected to galvanized earth lead GI wire 4 mm dia by means of bolts, nuts, check nuts and washer of galvanized iron or steel all as shown in electrical plate No 3 of SSR Part-I connected to continuous earth wire to DB all as specified and testing on completion, including provision of earth wire protected by 20mm dia GI light grade protection pipe from test point to main board and 20mm GI medium grade watering pipe funnel, PCC earth pit and RCC cover charcoal, salt and GI wire including excavation and earth work etc complete all as specified and directed.

Fixing only ceiling fan/Exhaust fan including PVC cable connection of 1.5 sqmm size 3 core obtained from BOQ item no 180 here in before after cleaning of blade of fans/exhaust fan complete all as specified and directed.

Fixing only Geyser including PVC cable connection of 2.5 sqmm size 3 core obtained from BOQ item no 180 here in before including plug top (if required) complete all as specified and directed.

S & F sheet metal enclosure single pole and neutral enclosure two pin and earth plug and socket complete with one single pole MCB 20 Amp for AC complete all as specified and directed.

Supply only modular metal flush box 8 module complete all as specified and directed.

Supply only modular metal flush box 6 module complete all as specified and directed.

Supply only modular metal flush box 4 module complete all as specified and directed.

Supply only modular metal flush box 3 module complete all as specified and directed.

Supply only white cover plate with frame 8 module complete all as specified and directed.

Supply only white cover plate with frame 6 module complete all as specified and directed.

Supply only white cover plate with frame 4 module complete all as specified and directed.

Supply only white cover plate with frame 3 module complete all as specified and directed.

S AND A ENGINEERS CONSTRUCTION CO

Pioneer Enterprises

M/s Prem Associates

M K ENGINEERS CO.

M/s. Shiva Engineers

SHREE MEGHALAYA CONSTRUCTION AND SUPPLY COMPANY