MAJOR GENERAL FABRICATION ERECTION CONTRACT JOB

Amount

Sulphur Furnace scrubber from M.S. Plate from 10mm (including all connections with pipe lines) A) Dismantling

B) Fabrication

C) Erection

Sulphur Furnace melter, receiver from M.S. Plate from 10mm (including all connections with pipe lines) A) Dismantling

B) Fabrication

C) Erection

Juice heater outer shell from MS plate 10mm including hydraulic testing at 50 psi for each juice heater A) Dismantling

B) Fabriaction

C) Erection

i) Fabrication & Erection (Fitting) of mud mixture scroll & side plates with proper Alignment & Commissioning

ii) Fabrication & Erection (Fitting) of mud mixture & side plates with proper Alignment & Commissioning

juice clarifier inside compartment coil from M.S. Pipe 5" with all connections complete job (as where it is) A)Dismantling

B) Fabriaction

C) Erection

Dismantling, Fabrication & erection of juice heater to angle valves, distance piece from M.S. Plate 10mm of diameter 12"

Dismantling, Fabrication & Erection of Juice Heater (top & bottom) compartment partition plate with rubber fitting channels from M.S/EN-8 square bar & rubber seal fitting to make it seal proof (to avoid short circuiting) i) Top Compartment

ii) Bottom Compartment

Dismantling Fabrication & Erection of MS Channel of rubber strips of juice heater compartment with M.S/EN-8 square

Dismantling, Fabrication & Erection of worn out semi Kestner catcher from M.S. plate size-8MM

QUAD Body shell from M.S Plate 12mm A) Dismantling

B) Fabrication

C) Erection

Top cone from M.S Plate 12mm A) Dismantling

B) Fabrication

C) Erection

Umbrella from M.S Plate 10mm A) Dismantling

B) Fabrication

C) Erection

Down Take from M.S Plate 12mm A) Dismantling

B) Fabrication

C) Erection

Save- All from M.S Plate 10mm A) Dismantling

B) Fabrication

C) Erection

PAN Body Shell from M.S Plate 12mm A) Dismantling

B) Fabrication

C) Erection

Top cone from M.S Plate 12mm A) Dismantling

B) Fabrication

C) Erection

Umbrella from M.S Plate 10mm A) Dismantling

B) Fabrication

C) Erection

Down Take from M.S Plate 12mm A) Dismantling

B) Fabrication

C) Erection

Save- All from M.S Plate 10mm A) Dismantling

B) Fabrication

C) Erection

Syrup tank from M.S plate 8mm A) Dismantling

B) Fabrication

C) Erection

Replacement / patch work of worn out body shell of final molasses storage tank with M.S plate

Replacement / patch work of worn out roof of final molasses storage tank with M.S plate

Dismantling, Fabrication & erection of suction pipes of injection/ spray pumps including reducer

Dismantling, Fabrication & erection of worn out portion of bottom, side plate & supporting angle/ channel of surup tank at pan station for each tank

Dismantling, Fabrication & erection of cooling coils of Crystallizers including connection pipe if any

Dismantling, Fabrication and erection water weighing & receiving tanks

Dismantling, Fabrication, Erection of magma mixture body including the drive units complete

Replacement of worn out round portion of crystallizer body

Repair and fitting of bush to Crystallizer's Central shaft

Replacement of worn out condensate juice receiving bottles with all connection

Dsimantling, Fabrication & Erection of scrapper hinge of juice clarifier

Dismantling, Fabrication & erection of Dorr's scrapper

Replacement of ventury of pan condenser from S.S plate

Replacement of C.I tail pipe of pan & quad

Replacement of condenser jet box

Dismantling, fabrication & erection of the bottom portion of pug mill (centrifigal machine)

Replacement of the outer shell of the Dorr clarifier

Replacement of the worn out portion cane carrier

Replacement/repair of worn out portion of sugar grader side plates & chutes

Replacement/repair of worn out portion of hopper

Replacement of hopper Air tray

1. Dismantling, Fabrication & erection of worn out shaft of Crystallizer no-3 including complete gear arrangement with complete commissioning.

2. Dismantling, Fabrication & erection of ribben type arms of crystallizer

Dismantling, fabrication & erection of superheater wash water tank with all connection, nipples, bends , valves & flange from 10mm plate

Dismantling, Fabrication & Erection of vaccumm filter condenser

Dismantling, fabrication & erection distribution plate of Central shaft of juice clarifier

Dismantling, Fabrication & erection mud boot of juice clarifier

Dismantling, Fabrication & erection shell of condenser of pan from SS plate

Dismantling & erection of spray pond with all connection including distance piece

Replacement of worn out of M.S Runner of inter carrier, elevator, RBC, cross carrier & cane Carrier Chains

Replacement of rail line of cane unloader with 50mm square bar

Replacement of worn out ducting of boiler & APCD including angle, channel, Flats & flanges

Replacement of side plates of cane carrier chain/RBC trough/cross elevator/Baggse elevator

Levelling of cross elevator chain trough

Mill house screw conveyor assembly (complete with bearings) A) Dismantling

B) fabrication

C) Erection

Replacement of worn out of APCD includes casing/ scrubber and flue gas entry connected to chimney portion etc.

Cane Cutter hodd and chopper top plate from 12mm thick M.s plate A) dismantling

B) fabrication

C) Erection

Dismantling, fabrication , erection of worn out portion of chute cane carrier to 1st mill

Replacment runner (flat size 50x8mm) of cane carrier / cross elevator / RBC/ baggase

Dismantling, Fabrication, erection of juice Tray of mill no 1 & 2 from S.s Plate A) 8mm

Dismantling, fabrication, erection of juice tray of mill No. 1 & 2 from s.s plate A) 6 mm

Repair of rotary baggase feeders of boilers A) Body

B) Rotor

Replacement of casing of boiler (both plate & supporting angle)

I.D Fan worn out casting of both boilers A) Dismantling

B) fabrication

C) Erection

Replacement of expansion joints of boilers

Replacement of worn out ducting the boilers

Erection and Fabrication of any thing from scrap

Replacement of inter carrier side plates

Replacement of scrapper bar side plates size :- 1 meter square

Replacement of the casting of air heater

Dismantling, loading & transportaion of juice hater from CSM Rakhra & unloading at CSm Budhewal

Erection of Juice Heater at CSM Budhewal with modification if any including trials and commissioning

Dismantling of Juice heater at CSM budhewal

(PART B) (General) Pipe Line M.S 1" to 12" dia a) Dismantling

b) Erection

Pipe Line M.S above 12'' dia (other than vapour pipe of pan and quad A) Dismantling

B) Fabrication

C) Erection

Pipe Line S.S 1" TO 12" dia A) Dismantling

b) Erection

Pipe Line S.S above 12'' dia (other than vapour pipe of pan and quad A) Dismantling

B) Fabrication

C) Erection

Pipe Line C.I. 1'' TO 12" dia A) Dismantling

B) Erection

Pipe Line C.I. above 12'' dia (other than vapour pipe of pan and quad A) Dismantling

B) Fabrication

C) Erection

Steam Pipe Line A) Dismantling

B) Fabrication

C) Erection

Steam Pipe Line bends A) Dismantling

B) Fabrication

C) Erection

(A) Bend M.S upto 12” dia a) Dismantling

b) Fabrication

c) Erection

(B) Bend M.S above 12” dia (other than Vapour pipe line of Pans & Quad) a) Dismantling

b) Fabrication

c) Erection

(A) Bend S.S upto 12" dia from 5mm to 7mm thick plate a) Dismantling

b) Fabrication

c) Erection

(B) Bend S.S. above 12" dia (other than Vapour pipe line of pans & Quad) a) Dismantling

b) Fabrication

c) Erection

Man hole of all sizes a) Dismantling

b) Fabrication

c) Erection

Flanges of all size a) Dismantling

b) Fabrication

c) Erection

M.S Tee/Nipple/Cross/Reducers a) Dismantling

b) Fabrication

c) Erection

Dismantling, Fabrication and Erection of M.S Coil

M.S Steam Coil

Dismantling and Erection of any type of valve

Plateform of any type a) Dismantling

b) Fabrication

c) Erection

M.S Structure work (Factory Building) a) Dismantling

b) Fabrication

c) Erection

M.S Tank having round & rectangular bottoms a) Dismantling

b) Fabrication

c) Erection

Trusses, Perlins, Columns & Beams (Factory Building) a) Dismantling

b) Fabrication

c) Erection

Plateform Pipe Line Railing of all sizes a) Dismantling

b) Erection

Electric Panel, DB and other machinery shed GI/ACC/MS Sheet a) Dismantling

b) Fabrication

c) Erection

Dismantling, Fabrication and Erection of Pump and Motor Bed of all Size

Valves Sluice/Angle/N.R./Butterfly a) Dismantling

b) Erection

VAPOUR/EXAUST pipe Line of quad and pan from M.S. plate 10mm a) Dismantling

b) Fabrication

c) Erection

VAPOUR pipe Line bend from M.S plate 10mm for quad and pan bodies a) Dismantling

b) Fabrication

c) Erection

Cone from M.S Plate a) Dismantling

b) Fabrication

c) Erection

Gutter from M.S. plate 5mm a) Dismantling

b) Fabrication

c) Erection

Sight Glass (Replacement)

Crystallizer Slide gate valve a) Dismantling

b) Fabrication

c) Erection

Dismantling, Fabrication and Erection of M.S shed of any type for panels, D.B., machines etc.

Fabrication and Erection of M.S terminal box of any type