SPECIAL REPAIR TO BLDG NO. P 265, VEHICLE SHED AT BLDG NO. P 433 AND PROVN OF TOILET NEAR BLDG NO. P 352 AND GUARD ROOM NEAR GATE NO. 2 AT MIL STN GADHIANGAR

Amount

Surface excavation not exceeding 30cm and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and directed.

Excavating in trenches not exceeding 1.5m wide and not exceeding 1.5 m in depth for foundation of pole, laying of cables etc in soft/loose soil and getting out.

Returning, filling in, including spreading, leveling, watering and well ramming in layer not exc 25 cm with soil obtained from excavation.

M&L for providing dry river sand as in sand cushioning to UG cable including punning gently all as directed. Note: Depth after punning shall be measured and paid.

Removing excavated material (Soil) not exc 50 mtr and depositing where directed at a level not exc. 1.5 m above the starting point.

M&L for hard core of gauge not exc. 63mm deposited spread and levelled in layers not exc. 15 cm thick, spread, levelled and rammed to a true surface including watering complete all as specified and directed.

M&L for treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area compete all as specified and directed.

M&L for treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) compete all as specified and directed.

M&L for treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface compete all as specified and directed.

M&L for treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area compete all as specified and directed.

M&L for plain cement concrete (1:4:8) type D2 using 40 mm graded stone aggregate in foundation filling and mass concrete complete all as specified and directed.

M&L for Pre-cast cement concrete (1:2:4), type B1, using 20mm graded stone aggregate, solid block in kerb stone of size 300mm x 300mm x 75mm, with plain fair faces, including chamfers, weathering, throating etc and set in cement mortar (1:4) complete all as specified and directed.

M&L for 35mm thick, precast cement concrete 1:2:4, Type B-0 using 12.5mm graded stone aggregate as in louvers and jallies, (measured solid) including all mouldings and precast cement concrete 1:2:4 type B-0, pillars/supports to jallies, set in cement mortar 1:4 complete including taking down old Jallies all as specified and directed.

M&L for RCC M-25 ( Design Mix ) ( using 20mm graded stone aggregate ) as in suspended slabs supported on walls/columns, in floors, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L RCC M-25 (Design mix) using 20 mm graded stone aggregate as in beam, cantilevers, bressumers, lintels over 1.5m span complete all as specified and directed.

Preparation for water proofing treatment to roof slab by applying one coat of cold bituminous primer @ 0.30 litre/sqm and confirming to IS-3384, laying APP based polystr modified membrane reinforced non wooven polyster of 3.50 kg/sqm (minimum) 3mm thick with plain polythene finished and sealing all the overlap 75mm in length side and 100mm in width side of membrane by torching including applying one coat of bituminous aluminium paint over membrane all as specified and directed.

Supply only, integral water proofing compound.

Supply only, liquid water proofing compound complete all as specified and directed.

M&L for Brick work with old size, sub class 'B' bricks, straight or curved on plan exc. 6m mean radius built in cement mortar (1:6) complete all as specified and directed.

M&L for Brick work with old size, sub class 'B' bricks, straight or curved on plan any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

Supply and laying sub class old 'B' burnt bricks, size of brick 230x115x75mm, laid as cable protection cover complete all as specified and directed.

Cutting holes exc 150 sq cm but not exc 400 sq cm in stone walls built in cement mortar or cement lime mortar and walls on cement concrete

M&L for form work to soffit of suspended slabs such as roof slabs, floor slabs, landings and simillar works not exceeding 20cm thick and fair finished surfaces of concrete all as specified and directed.

M&L for form work to soffit of suspended slabs such as roof slabs, floor slabs, landings and simillar works not exceeding 20cm thick and rough finished surfaces of concrete all as specified and directed.

M&L for form work to soffit of suspended slabs such as roof slabs, floor slabs, landings and simillar works not exceeding 20cm thick and fair finished surfaces of concrete all as specified and directed.

M&L for form work to sides and soffit of floor or roof beams, beams haunchingss, girders, brussummers, lintels, cantilevers, shelves including sup-ports, overhangs, etc and rough finished surfaces of concrete all as specified and directed.

S&F factory made 30mm thick flush shutters, solid core construction, with block board core and plywood face panles, commercial type on both sides complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from the frames) exc. 1.5sq.m but not exc. 4sq.m each complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sqm each complete all as specified and directed.

S&F, factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site complete all as specified and directed.

S&F, solid PVC door frame of size 50mm x 47mm, made out of 5mm plain colour PVC sheet, reinforced with MS Square tube, supplying and fixing in opening as per specifications complete all as specified and directed.

S&F, PVC/iron 5mm thick plain color PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specification and drawing complete all as specified and directed.

S&F, in repair, aluminium anodised, barrel tower bolts of extruded section with length of bolt 150 mm and fixed complete all as specified and directed

S&F aluminium anodised, barrel tower bolts of extruded section with length of bolt 200 mm and fixed complete all as specified and directed

S&F, 5mm thick, black tinted glass panes fixed to aluminium doors/windows/vents with necessary rubber gaskets complete all as specified and directed.

S&F, aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy with length of bolt 300 mm and fixed complete all as specified and directed.

S&F, butt hinges, medium weight, cold rolled, mild steel of size 100 mm complete all as specified and directed.

S&F, butt hinges, medium weight, cold rolled, mild steel of size 125 mm complete all as specified and directed.

S&F, aluminium anodised handles, cast type 125mm size complete all as specified and directed.

S&F extruded aluminium alloy handles, fabricated type, anodised of size 150 mm complete all as specified and directed.

S&F, brass chromium plated, tubular towel rail 20mm dia, D type, 600mm long complete all as specified and directed.

S&F, in repair, 150mm long floor door stopper of aluminium alloy body and tongue with hard drawn steel spring complete all as specified and directed.

S&F, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for mild steel TMT bars 6 to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for mild steel TMT bars, 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bend to shape required and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for rolled mild steel angle iron work fixed independently, without connecting plates etc( cut to ordinary lenghts) conforming to Fe-410 (Gde-E-250) complete all as specified and directed.

S&F, MS angle iron Fe-410-W (Gde-E-250) quality A in framed work for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc complete all as specified and directed.

M&L for rolled mild steel angle iron work as in door frames complete, drilled for fixing of hinges etc. also fastening and fixing conforming to Fe-290 (Gde-E-165) complete all as specified and directed.

S&F mild steel work in tubular trusses, posts, main and cross beams, hip and jack rafters, purlins, including special shaped washer etc. complete using ERW or induction butt welded tubes, conforming to IS 1161-1979, Gde St-240 complete all as specified and directed.

S&F, 3mm dia galvanized steel wire 50 x 50mm mesh made up into mattresses or eages, lapped, wired and laid in position including closing after filling all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails straining bolts, etc including provision of binding wire complete all as specified and directed. Note: supply only chain link fencing, MS 10mm dia round bars as line wire and MS flat iron shall be measured and paid separately under respective item of this schedule.

S&F, factory made steel windows with side hung shutter including box type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded including applying one shop coat of red oxide primer complete all as specified and directed.

S&F, factory made steel ventilators with top hung shutter including hinges, steel peg stay, glazing bars including applying one shop coat of red oxide primer all as specified and directed

Supply only mild steel galvanised, chain link fencing of 50x50mm mesh size and 3mm dia wire complete all as specified and directed.

S&F, pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet, 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F, Aluminium anodised doors/windows/ventilators with one or more rebates including joining cleat for fixing etc complete with frames, shutters and grills of size directed by Engineer-in-charge including handles, tower bolts, grills, etc complete all as specified and directed. Note:- Floor door spring, sheet glass, wire cloth, lock, etc shall be measured and paid seperately.

M&L for machine cut kota stone slab, 450x600mm,(18"x24") 20-25mm thick as in flooring laid over and including cement mortar screed bed of 15mm thick in CM (1:6), laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer-in-charge.

M&L for machine cut kota stone slab 18-20 mm thick in riser of steps, skirting, dado and pillar laid over and including rendering 10mm thick in cement mortar (1:4), jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for 50mm thick cement concrete (1:3:6) type C1, using 20mm graded stone aggregate as in plinth protection, finishing cement concrete surfaces even and smooth without using extra cement, Joints of plinth protection shall be filled with bitumen mastic (1:3) complete all as specified and as directed.

M&L for 75mm thick cement concrete 1:3:6 type C1, using 40mm graded stone aggregate as in plinth protection, finishing cement concrete surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for 100 mm thick cement concrete (1:4:8) type D-2 using 40 mm graded stone aggregate as in sub base of flooring/hard standing and finishing the surface even and fair without using extra cement complete all as specified and directed.

M&L for 75 mm thick cement concrete (1:4:8) type D-2 using 40 mm graded stone aggregate as in sub base of flooring/hard standing, path and finishing the surface even and fair without using extra cement complete all as specified and directed.

M&L for 50mm thick PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in floors and finishing the top surface even and smooth without using extra cement complete all as specified and directed.

M&L for 40mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate in sub base to receive floor finishes without using extra cement complete all as specified and directed.

M&L for cutting uneven surfaces of concrete & cutting reinforcement from drops of fins & facias (thickness not exceeding 50mm) using necessary scaffolding and making good the disturbed portion with 5mm thick rendering in CM 1:3 finished even and smooth without using extra cement etc. complete all as specifeid and directed.

S&F 10 mm thick sheet glass plain exc 0.50 sqm of each pane fixed with wall with stainless steel fasteners and drilling in glass pane sheet complete all as specified and directed (Note : S/S fastener shall be measured and paid separately.

Supply only stainless steel fasteners 75 mm long all as specified

M&L wall tiles 200mm x 70 mm size and 12mm thick premium quality earthen ware moulded tiles including and over 10mm thick cement mortar 1:4 and jointed pointed in cement slurry using pigment to match the color of tiles.

M&L for Coloured glazed ceramic tiles of size 300 x 200 x 7mm thick, on vertical wall surface, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces over and including 10mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 450mm x 300mm x 7mm on vertical surface such as skirting, dados, risers to steps etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, over and including rendering 10mm thick in cement mortar (1:4) , complete all as specified and directed.

M&L, Non-skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete as specified and directed.

M&L for light shade, vitrified tiles, 10mm thick (square/ rectangular polished, area of each tiles not exceeding 0.36 sqm, in flooring set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed or bedding layer of 15 mm thick cement mortar (1:6) complete all as specified and directed.

M&L for Dark shade, vitrified tiles, 10mm thick (square/ rectangular polished, area of each tiles not exceeding 0.36 sqm, in flooring set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed or bedding layer of 15 mm thick cement mortar (1:6) complete all as specified and directed.

M&L for chequered cement concrete tiles 20 cmx20 cmx25 mm thick, with grey cement and pigment, set, jointed and pointed in neat cement slurry over and including 15 mm thick screed bed in CM (1:6) as in floor complete all as specified.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) and removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

S&F for machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size conforming to IS 15658- 2006 of 60mm thickness, M-35 grade including 25mm thick sand cushion below paver blocks complete all as specified and directed.

M&L for 18-20mm thick black granite stone slab machine cut in skirting/dado, cooking platform, jams, pillars, windows cills and the like laid over and including 10 mm thick screed bed or backing coat on cement mortar (1:4) and jointed with grey cement slurry and pointed with white cement and with admixture or pigment to match the shade of granite stone including and polishing complete all as specified and directed.

M&L for rendering cement plaster 10mm thick in cement mortar (1:6) on brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering cement plaster 5mm thick in cement mortar 1:3 on fair faces of concrete in ceilings, chajjas, fins facia etc. complete all as specified and directed.

M&L for rendering cement plaster 5mm thick in cement mortar 1:4 on fair faces of concrete in ceilings, chajjas, fins facia etc. finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering cement plaster 15mm thick in cement mortar 1:4 on stone masonry surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:4) on walls/ floors surfaces mixed with using water proofing compound @ 3% by weight of cement or as per manufacturer instructions, finished even and smooth without using extra cement to receive WPT complete all as specified and directed. Note:- Supply only water proofing compound shall be measured and paid separately.

M&L for screed bed or bedding layer of 20mm thick for laying floor finishes on green surface of roof slab in cement mortar 1:3 complete all as specified and directed.

M&L for preparation of new plastered or un platered surfaces of wall and applying two coats of cement base paint complete all as specified and directed.

M&L for preparing new plastered or un-plastered ceiling surfaces and applying three coats of white wash complete all as specified and directed.

M&L for preparing old plastered or un-plastered ceiling surfaces and applying two coats of white wash complete all as specified and directed.

M&L for preparation of old decorated plastered or unplastered wall surfaces including brooming down or steel wire brushging, scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of distemper oil emulsion complete all as specified and directed.

M&L for preparing new plastered or un-plastered walls surfaces and applying three coats white wash complete all as specified and directed.

M&L for preparing old plastered or un-plastered surfaces of wall and applying two coat of cement base paint complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of white cement as primer complete all as specified and directed.

M&L for 3mm thick sheet glass, ordinary quality and glazing with oil putty in square not exc. 0.5sq.m in each pane complete all as specified and directed.

M&L for 3mm thick figured glass, pin headed type and glazing with oil putty in square not exc. 0.5sq.m in each pane complete all as specified and directed.

M&L for preparation of new wooden surface of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L for preparation of old wooden surface of any description, over 10cm width or girth and applying one coats of synthetic enamel paint complte all as specified and directed.

M&L for preparation of new steel surface of any description not exc. 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 15mm bore of pipe complete all as specified and directed.

S&F, steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 20mm bore of pipe complete all as specified and directed.

S&F steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors for 25mm bore of pipe complete all as specified and directed.

Supply, hoisting, fixing in position and connecting, 500 litres capacity rotational moulded polyethylene water storage tank double layered (cylindrical, vertical with closed top), ISI marked, including fixing arrangement for inlet/outlet/over flow and vent pipe of standard size all as specified in SSR Part-I complete all as specified and directed.

S&F, bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule of 15mm bore complete all as specified and directed.

S&F, pillar tap, cast copper alloy with capstan head, chromium plated, screwed down high pressure, with or without lettered 'hot' or 'cold' with long screwed shanks and fly nuts, screwed for iron pipes 15mm bore complete all as specified and directed.

S&F, in repair, stop valves, cast copper alloy, fancy type, chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes or for unions of 15mm bore complete all as specified and directed.

S&F, ball brass valves, high pressure, with polythene float and fly nut, screwed for iron pipe and fixed complete all as specified and directed for 20mm bore of pipe.

Supply only 32mm, waste fittings, brass chromium plated for glazed ware sink, basins, etc. with long screw shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S&F, PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F, 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints laid in trenches or floor complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to walls including stack clamp complete all as specified and directed.

S&F, 110mm bore PVC (SWR) bend, any radius, with access door complete all as specified and directed.

S&F, 110mm bore PVC (SWR) branch piece, single(Single Y) equal or unequal complete all as specified and directed.

S&F, 110mm bore PVC (SWR), vent cowl complete all as specified and directed.

S&F, 110mm PVC (SWR) WC connector bent type complete all as specified and directed.

M&L for cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregate as in bed to drain pipes including packing under and hunching against the sides of pipe after they are laid and tested for 150mm bore of pipe complete all as specified and directed.

M&L for salt glazed stone ware drain pipes, 150mm internal diameter, grade 'A' laid in trenches and jointed complete all as specified and directed.

S&F, in repair, vitreous china squatting pan, 'Orissa' pattern of size 580mm x 440mm with integral foot rest (excluding flushing cistern and flush pipe) including joining, filling and provision of cement concrete bedding 1:5:10, type E-1, using 20mm graded aggregate complete all as specified and directed.

S&F, in repair, 10 litres capacity, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet ball valve, float and handle including brackets and connection to pipe or lever etc. complete all as specified and directed.

S&F, in repairs, vitreous china wash basin, white, flat back of size 550mm x 400mm including waste fitting and brackets grouted in cement mortar 1:2 in wall complete all as specified and directed. Note :- Supply only pillar taps, waste fittings, PVC connection, PVC waste pipe shall be measured and paid separately.

S&F, 40mm bore ligh density polythene pipes (LDPE) of pressure rating 6 Kgf/Sqcm fixed complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc. complete all as specified and directed.

Demolition of pre cast cement concrete articles set in cement mortar including all quoins, arches, pillars etc. complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified and directed.

Dismantling asbestos cement (corrugated, semi corrugated etc.) sheets in roof covering complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for.

Dismantling textile coverings including frames (if any) and cover fillets (measured flat and not girthed)

Dismantling barbed wire fencing mesh, fixed with steel or wood fillets of any type complete all as specified and directed..

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded in ( Concrete, brick work,masonry), portion and making good sturbed ground

Taking down carefully unserviceable copper/aluminium point wiring (Light, fan, socket or power) complete including unserviceable fittings and fixtures such as switches, ceiling roses, pendents, regulators, sockets, lamp holders, brackets, except ceiling fittings, bulk head fittings, tube light fittings etc. and making good the disturbed surfaces of walls, floors, etc. complete all as specified and directed.

M&L for wiring with and including multistranded copper conductor 1.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number drawing through in and including medium grade, rigid non metallic PVC concealed conduit of 20mm bore and including cutting chases for conduits and sinkings for boxes, its accessories and including with multistranded copper conductor 1.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number as continuity earth wire terminating with new modular sunken concealed terminal boxes complete all as specified and directed for the following :-

(a) One light/fan point controlled by one switch

(b) One 3 pin, 5 Amps, socket outlet on the same board controlled by another switch.

(c) One multi pin 5 Amps, socket outlet on Independent board.

M&L for wiring with and including multistranded copper conductor 2.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number drawing through in and including medium grade, rigid non metallic PVC concealed conduit of 20mm bore and including cutting chases for conduits and sinkings for boxes, its accessories and including with multistranded copper conductor 2.5 Sqmm (nominal cross sectional area) single core, PVC insulated, unsheathed FRLS cable 1100 Volts grade, ISI marked with valied CML number as continuity earth wire terminating with new modular sunken concealed terminal boxes complete all as specified and directed for the following :-

Supplying & laying, XLPE insulated, PVC inner sheathed, armoured with galvanised steel strip or wire heavy duty underground cable with aluminium multi stranded conductor, 1100 volt grade, laid in trenches/duct, passing through pipe/duct or fixed on pole and connecting and testing complete including taking down old unserviceable cable of sizes 6 Sqmm 2 core complete all as specified and directed.

Supplying & laying, XLPE insulated, PVC inner sheathed, armoured with galvanised steel strip or wire heavy duty underground cable with aluminium multi stranded conductor, 1100 volt grade, laid in trenches/duct, passing through pipe/duct or fixed on pole and connecting and testing complete including taking down old unserviceable cable of sizes 6 Sqmm 2 core complete all as specified and directed.

S&F, lamp holder, PVC/Polycarbonate, with back plate suitable for batten fittings complete all as specified and directed

S&F, switch piano, flush button, single pole, one way, 5 Amps complete all as specified and directed

S&F, switch piano, flush button, single pole, one way 15 Amps complete all as specified and directed

S&F,Socket, flush button, single pole, one way 15 Amps complete all as specified and directed

S&F, socket outlet, 2 in 1, 3 pin, 5 Amps, flush type complete all as specified and directed

S&F, in repairs, sheet metal distribution board, SPN, 2 way 240 Volt, double door factory made and tested complete, protection class IP-42 suitable for mounting MCBs, isolator with 200 A tinned copper bus bar complete all as specified and directed

S&F, in repairs, sheet metal distribution board, factory made and tested complete, protection class IP-42 suitable for mounting MCBs, isolator with 200 A tinned copper bus bar of capacity 200 Amps of SPN, 4 way 240 Volt complete all as specified and directed

S&F, ceiling rose, 3 terminal , any shade, of PVC/Polycarbonate, isolated body complete all as specified and directed

S&F, miniature circuit breakers, type curve ‘B’ , 10 KA, SP, 6-32 Amps complete all as specified and directed.

S&F, miniature circuit breakers, type curve ‘B’ , 10 KA, SP, 32-40 Amps complete all as specified and directed.

S&F, ceiling fan 1200mm sweep, BLDC type, 230V, AC, 50 Hz, including electronic type fan regulator, single phase electric supply, ISI Marked with all standared fittings including PVC cable 1.5 Sqmm, 3 core, 1100 volts, round from ceiling rose to the fan and writing of MES Nos with black synthetic enamelled paint complete qll as specified and directed.

S&F, Exhaust Fan, 200mm Sweep, single phase, 230/240 volts, 50 Hz, including making opening for exhaust fan including grouting nut , bolts and washer for fixing of fan and making good the disturbed surfaces all as per existing and mounting fan including connected with three core copper conductor cable 0.75mm complete all as specified and directed .

S&F, LED light fitting, batten type, housed in extruded from powder coated aluminium, 10 Watt connected with three core copper conductor cable of suitable size and testing complete all as specified and directed.

S&F, LED light fitting retrofit, batten type, housed in extruded from powder coated aluminium, 20 Watt connected with three core copper conductor cable of suitable size and testing complete all as specified and directed. Make : Bajaj Model No. 830233 for fitting and Model No. 830232 of light or equivalent make as approved by GE from the makes specified under Appx 'C'.

S&F, in repair, LED Oval bulk head 10 watt complete all as specified and directed.

S & F, in repair, Distribution Board Power line VTPN, 4 way, 415 volts, factory made, powder coated, double door with neutral and earth link including 3 pole MCCB 63 Amps rating, 10KA breaking capacity for incoming supply and including 12 Nos single pole MCBs 6-32 Amp 'C' series for out going supply complete all as specified and directed.

S&F, air circulation fans 230 Volts single phase osciliting 600mm sweep suitable for wall mounting incl mounting arrangement complete all as specified and directed. (Note: Old unserviceble air circulator fans to be deposited in MES store yard for further disposal)

S&F LED flood light 80 watt, medium bay IP-65 luminaire with high efficacy single phase 230 volt supply complete all as specified and directed.

ALBA AC AND REF SERVICES

SATISH ELECTRICALS

nevi constructions

Ramdev and Sons

Haritwal traders

DMA PROJECTS