CMLRRP 2019-20 , CHELAKKARA LAC , PALLUR COLONY CHIRACOLONY ROAD WARD 4 ( SL NO 319 ) AT DESAMANGALAM G.P, WADAKKANCHERY B.P

Amount

Retarring

75.5.5.B.2pb : Modified Penetration Macadam 75 mm thick using Bitumen S-65 - Packed Bitumen Rates <br> Construction of penetration macadam over prepared base by providing a layer of compacted crushed coarse aggregate using chips spreader with alternate applications of bituminous binder and key aggregates and rolling with a three wheel 80-100 kN static roller to achieve the desired degree of compaction as per Technical Specification Clause 506.

75.5.5.A.1pb : Modified Penetration Macadam 50 mm thick using Bitumen S-65 - Packed Bitumen Rates <br> Construction of penetration macadam over prepared base by providing a layer of compacted crushed coarse aggregate using chips spreader with alternate applications of bituminous binder and key aggregates and rolling with a three wheel 80-100 kN static roller to achieve the desired degree of compaction as per Technical Specification Clause 506.

75.5.9.2.2.Pa : Plastic Roads - Bitumen S-65 <br> 20mm thick Open-Graded Premix Carpet using Bituminous (penetration grade/modified bitumen) Binder <br> Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508 (with 7% of bitumen replaced by shredded waste plastic) <br> Case - I By Manual Means <br> (II) Bitumen (S-65) (VG - 30)

75.5.2.1pb : Tack Coat - With Packed Bitumen Rates <br> Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.

75.5.12.A.3.2pb : Seal Coat - Manual Means - Type C - Bitumen S-65 - Packed Bitumen Rates <br> Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A, Type B and Type C as per Technical Specification Clause 510 <br> A. By Manual Means <br> Case III : Type C <br> (II) Bitumen (S-65)

Side berm concrete

3.5.1 : Excavation in Cutting in Soil by manual means with lead upto 50 mExcavation for roadway in soil using manual means for carrying of cut earth to embankment site with a lift upto 1.5 m and lead upto 50 m as per Technical Specification Clause 302.3

od631551/2020_2021 : Filling with Quarry Muck &lt;br&gt; Filling up low lying and water logged areas with local material/ quarry muck, spreading in layers, leveling the top at site and consolidation by ramming, etc complete for improving the CBR value of subgrade

11.4.3.1 : Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203III.P.C.C. grade M 20 (i)Nominal mix (1:2:4)

Name Board &amp; Marking

od638464/2020_2021 : Providing and fixing of direction and place identification retro-reflectorised sign with 7&lt;br&gt;years warranty&lt;br&gt;manufactured as per IRC :67 High Intensity Micro Prismatic (Type IV) grade sheeting fixed over&lt;br&gt;aluminium sheeting, 2 mm thick/ aluminium composit material sheeting 4 mm thick with area exceeding&lt;br&gt;0.9 sqm, with suitable back supporting frame of MS angle 40x40x6 and supported on suitably designed&lt;br&gt;GI pipe pole not less than 50mm NB , 2 Nos. confirming to IS 1239, firmly fixed to the ground by means&lt;br&gt;of properly designed foundation with M 15 grade cement concrete min size 45 cm x 45 cm x 60 cm, 60&lt;br&gt;cm below ground level including painting all exposed surface with 2 coats of epoxy painting over epoxy&lt;br&gt;primer and as per approved drawing and clause 801 including lettering symbols etc.(Moth 8.6 modified)

od638465/2020_2021 : :Providing and fixing reflective road studs (Raised Pavement Marker) of &apos;category A&apos;&lt;br&gt;made out of ASA/HIPS/ABS moulded body with shanks and conforming to ASTM D 4280, strong enough to&lt;br&gt;support a load of more than 13.635 T when tested in accordance with ASTM D 4280, reflective panel&lt;br&gt;confirming to ASTM D 788, and reflectivity conforming to clause 804.4 including installation, drilling, fixing&lt;br&gt;with adhesive etc with 2 years warranty for the road stud as well as for in field performance as per clause&lt;br&gt;804.7.3.&lt;br&gt;Raod Markers/Road Stud with Lense Reflector:-&lt;br&gt;(Morth 8.35 modified)&lt;br&gt;

od638466/2020_2021 : :Providing and laying of hot applied thermoplastic compound 2.5 mm thick including&lt;br&gt;reflectorising glass beads on BItuminous Surface @ 250 gms per sqm area, thickness of 2.5 mm is exclusive&lt;br&gt;of surface applied glass beads as per IRC : 35. The finished surface to be level, uniform and free from&lt;br&gt;streaks and holes. (Morth 8.13 modified)

od638467/2020_2021 : Direction and place identification signs more than 0.90 sqm sign board&lt;br&gt;&lt;br&gt; &lt;br&gt;B.Semi-Reflective Traffic signs&lt;br&gt;Providing and erecting direction and place identification of semi reflective sign boards as per IRC-67 made of 2 mm thick M.S. Sheet duly stove enameled paint white colour in front and grey colour on back with reflective border of 70 mm width and required message, letters, figures with reflective tape of engineering grade as per MORD specifications of required shade and colour. Supported and welded on two nos. 47 mm x 47 mm of 12 SWG square tube of 3050 mm height duly strengthened by 25 mm x 5 mm MS flat iron on edges on back firmly fixed to the ground by means of properly designed foundations with M-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and Technical Specification Clause 1701 (modified MoRD 10.4.B)

K K ASHARF

Bidder Name

K K ASHARF

SUBAIR