SPECIAL REPAIR OFFRS MD ACCN BLDG NO P-371 IN OFFRS ENCLAVE (02 X OTRS CAPT AND BELOW) AT MILITARY STATION JAMNAGAR

Amount

Demolition of concrete of any description and in any position not other wise specially provided for cement concete (unreinforced) and all as specified and directed.

M&L 15mm thick rendering in cement plaster 1:3 with WPC on bottom and side walls of sunken floor incl finished even and smooth w/o using extra cement all as specified.

M&L filling PCC type E2 1:5:10 (40 mm graded stone aggr) as in sunken floor after applying appropriate treatment to side walls cmplete.

M&L for 40 mm thick PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate mixed with liquid water proofing compound @3%of cement in bottom of sunken floors floors.

M&L Cleaning vertical and horizontal surfaces of sunken slab using wire brushing followed by sanding with emery paper for loose materials/dust and applying two coats of epoxy resin component (Dr. Fixit DAMPGUARD or equivalent) solution/mix using nylon brush pouring Base part in appropriate container followed by the Hardner part and mix thoroughly to attain homogeneous smooth paste and dilute the mixed compound with water in ratio 1 part Base: 1 part Hardner: 1 part water by slow addition and mix thoroughly until a brushable consistency is obtained, first coat will be allowed to dry for 6 to 8 hrs before application of second/final coat) incl curing treated surface for 24 hrs complete incl applying evenly a coat of blown bitumen @ 1.5kg/sqm over entire treated surfaces incl spout holes complete and all as specified as per manufacturer instruction.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar .

Roughening surfaces of old concrete surfaces by picking, sweeping clean and washing down with water to remove dust, etc complete all as specified.

S&F Glazed ceramic tiles in vertical surface 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick plaster in CM 1:4 .

S&F Non-skid ceramic tiles 7 to 8mm thick (square / rectangular ) area of each tiles exceeding 0.06 Sqm but not exceeding 0.11 sqm, in floor/ etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, including 15mm thck screed bed in CM 1:4 .

M&L Machine cut & polished Kota stone slab as in flooring, cill of window single piece over lap 20-25mm thick laid over screed base ,laid & ,jointed with grey cement slurry mixed with pigment to match the shade of the slab steps, jambs, pillars, window- cills, etc including 20mm thck screed bed in CM 1:3 .

M&L 20mm thick Granite(of any type) work (table rubbed and polished) in cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 20 mm thick screed bed in CM 1:3 all as specified and directed

Moulding to Granite(single or double) slab including rounding off edges for 20 mm thick slabs including grinding and polishing

S&F Coloured Vitrified tiles 10 mm thick (square/rectangular) polished area of each tiles n exc 0.36 sqm in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match in light shade including 15 mm thick screed bed in CM 1:6

Demolition of concrete of any description and in any position not other wise specially provided for cement concete (unreinforced) and all as specified and directed.

M&L 100mm thick PCC type C-2, 1:2:4 (40mm graded stone aggt) as in path, hard standing, parking floors etc. complete all as specified and as directed.

M&L 40 mm thick Cement concrete type B-1, 1:2:4 (20 mm graded aggregate) as in plinth protection

Taking down all existing roof treatment and demolition of cement concrete padding/levelling course incl wire brushing and cleaning loose dust etc from surfaces of RCC roof incl flashing and juntion of parapet complete all as specified.

Roughening surfaces of old concrete surfaces by picking, sweeping clean and washing down with water to remove dust, etc incl brushing neat cement slurry with 3.0 kg of cement per sq metre complete all as specified.

M&L 25mm thick PCC 1:2:4, type B0 (using 12.5mm size stone aggregate) as levelling course incl finished even and smooth using extra cement complete all as specified

M&L for 10 mm thick rendering in CM 1:3 over concrete surfaces (Roof) mixed with liquid water proofing compound @ 3% of cement complete all as specified. NOTE:- Liquid water proofing compound shall be measured and paid for separately as “Supply only”.

Supply of integral water proofing compound

M&L for applying roof treatment on top of roof with APP modified membrane (minimum 3 mm thick) weight not less than 3.00 Kg/sqm and reinforced with non-woven polyster reinforcement/mat (centre core) with thermal insulation with polythene finish on upper side of membrane, laid by torch application method with overlaps 150 mm on length side and 100 mm on the width side as per manufacturer’s instructions over a coat of approved cold applied bituminous oil based primer (IS-3384) @ 300 gm/sqm and applying two coats of aluminium paint 0.20 litre/sqm complete all as specified and as directed by Engineer-in-Charge.

S&F powder coated aluminium sliding window of 3 tire, frame of section 62mm X 32mm X 1.47 mm or appropriate equivalent section and shutters of section 18 mm X 44 mmX 1.35 mm or appropriate equivalent section fixed with 4 mm thick tinted sheet glass with rubber gasket, handles, locking arrangement and aluminium wire mesh incl making good jambs, cills etc and including taking down old iron window complete all as specified and directed by the Engr-in-Charge

S&F in powder coated aluminium fixed louvered ventilator, frame of section 63.5mm X 38.1mm X 1.01 mm or appropriate equivalent section with 4 mm thick figured/frosted sheet glass with rubber gasket,Aluminium wire mesh, handles, locking arrangement etc incl making good jambs, cills etc and including taking down old iron ventilator complete all as specified and directed by the Engr-in-Charge.

Taking down cement plaster on brick/stone or concrete surfaces including racking out joints, hacking for key,scrubbing down with water to receive plasterincluding necessary all scaffolding complete all as specified

M & L for rendering 10mm thick plaster in CM (1:6) on surfaces of brick work/ stone masonry /concrete surface, finished even and fair without using extra cement complete.

M&L for rendering 5 mm thick in CM 1:4 mixed with liquid water proofing compound3% of cement, over and including 10 mm thick rendering in CM 1:6 on stone masonry surfaces or surface other than fair faces of brick work or on one side of lathing. Note:- Liquid water proofing compound shall be measured and paid for separately as “Supply only”

M&L for rendering 5 mm thick in CM 1:3 on concrete surfaces in ceiling including finishing even and smooth without using extra cement.

M&L Preparation of newly plastered surface and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

M&L for preparation of new plastered surface of wall and applaying two coat of oil bond distemper and 3 mm putty all as specified and directed

M&L for preparation of new plastered surface of ceiling and applying three coats of white wash.

M&L Preparing old decorated surfaces by complete removal of existing treatment, scraping down, washing, rubbing down and stopping of painted surface of walls & ceiling including roof projection / chajjas and by hand held sander / long handle sander including cornices, pilasters etc (Plastered or unplastered surfaces) and applying Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade on Two coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.9lit/10 sqm complete all as specified and as directed.

Complete Removal of existing treatment on ceiling and applying two coats of white wash acomplete.all as directed.

Complete Removal of existing treatment on wall and applying two coats of oil bond distemper and 3 mm putty all as directed.

M&L preparation of old painted surfaces of wood/ wood based materials of any description over 10Cm width or girth and applying one coat of synthetic enamel paint etc. complete all as specified and directed by Engineer-In-Charge.

Removal of all loose/unsound/bad/damaged concrete or plaster existing RCC structure of slab/beams/walls/chajja by using chesel/hammar .Cut and remove unsound reinforcement bars, wires etc without damaging the sound reinforcement . clean loose rust from bars manually with brush . fixing new supplymentary bars if required,either by tying it with existing bars or by welding on it. Applying eppoxy bonding agent and making good with polymer modified plaster/micro concrete as required thickness over a coat of rust removing alkaline primer and match the finishing to the existing surface in ground floor including formwork complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) each area n.exc 1.5 sqm all as complete all as specified and directed by the Engr-in-Charge

Taking down chowkats or frames with shutters (without taking off shutters from the frame) each area exc 1.5 sqm but n.exc 4.0 sqm complete all as specified and directed by the Engr-in-Charge

S&F Pressed steel frames for doors size 125 mm X 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed by the Engr-in-Charge

S&F Pressed steel frames for doors size 105 mm X60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed by the Engr-in-Charge

Providing cement concrete type B 0 1:2:4 using 12.5 mm aggregate filling in Pressed steel hollow door section complete all as specified and directed by the Engr-in-Charge

S&F Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and as directed.

S&F factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel designed with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face incl particle board core complete all as specified and as directed.

S&F 35 mm thick Flush shutters, solid core constuction, with block board core and plywood face panels, commercial type on both sides supplied and fitted to chowkats complete all as specified and directed.

S&F 35 mm thick 2nd class hardwood factory made glazed & skeleton door shutter open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.20 (a) complete all as specified and directed by the Engr-in-Charge

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or stainless steel wire staples or with second class hard wood beadings complete all as specified and directed by the Engr-in-Charge

S&F100mm butt hinges,extruded aluminium alloy with galvanised mild steel hinge pin,anodised and fixed,tupe B1 complete all as specified and directed by the Engr-in-Charge

S&F 250 mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast aluminium complete all as specified and directed by the Engr-in-Charge

S&F Extruded aluminium alloy handles 150mm long, fabricated type, anodised complete all as specified and directed by the Engr-in-Charge

S&F Aluminium anodised barrel tower bolts, 150 mm long, of extruded section complete all as specified and directed by the Engr-in-Charge

M&L preparation of new untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer..

S&F in repair 25mm dia stainless steel curtain rail, cut in required length and size to fit with opening incl fixing on bracket with necessary screws fitted on bracket and decorative nobs on sides with necessary arrangement complete all as specified and as directed by Engr-in-charge.

S&F in repairs curtain rod side brackets of stainless steel, angular or cantilever type fixed to wall with 02 nos screws on each bracket and fitted screws for fixing curtain rod incl CP/stainless steel carved decorative design plain metal colour nobs with fixing arrangement for curtain rod using a screw complete all as approved and shown by Engr-in-charge.

Dismantling boardings, any description, fixed in any position with screws complete all as specified.

M & L 18/19mm thick Pre-laminated particle board, interior grade, prelamination one side with decorative choice lamination & other side balancing white lamination, fixed with nails as in cupboards / cabinets incl locking arrangement .

S&F 18/19 mm wide 6 mm thick lipping on veneered particle as in cupboard shutter and shelves.

S&F in repairs 2nd class hardwood plain fillet square rectangular in section wrought sawn secured with screws exc 13 & n exc 25 sqcm in section all as specified and as directed by Engineer-In-Charge..

S&F75 mm butt hinges,extruded aluminium alloy with galvanised mild steel hinge pin,anodised and fixed,tupe C21

S&F Extruded aluminium alloy handles 100mm long, fabricated type, anodised.

S&F Aluminium anodised 75mm hasp and staple ,safety type with hinge pin including bolt to hinge plate and fixed with screws

S & F in repairs white vitreous china washed down water closet pan, (pedestal pattern), white, with and including P/S Trap, PVC solid type seat cover etc complete.

S&F in Repairs Health Faucet with 1.50mtr tube & Hook any description including flexible attachment Make Prayag or equivalent make specified

S/F in repairs PVC valveless syphonic action type ,flushing cistern Low level white,with,with inlet ball valve ,float and handle 10 Ltr capacity including brackets.

S&F in repairs Flush pipe of Polyethylene of low or high density or PVC 32 mm dia. for low level cistern

S&F in repairs counter sunk Vitreous china wash basin(560x410x180mm), white , excluding taps, waste, chain and plug and porcelain stopper but including mounting on granite slab 20 mm thick and fixed with brackets complete all as specified and directed

S&F 32 brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary picking , union and cap and fixed all as specified and directed.

S&F decorative type Mirror of 5/6 mm thick with beveled /grind without beading and CP screw with plugs as specified and all as directed by Engineer-In-Chagre

S&F in repairs Brass CP Central hole Basin Mixer without Pop-up and joint with adhesive , taflon tape. Make Prayag or equivalent make specified

S&F in repairs Brass CP wall Mixer for mixing hot & Cold water screwed down for iron pipe and fixed.make and joint with adhesive , taflon tape

S & F in repairs brass chromium plated over head shower with arm 255 mm with flange size fency type with or without swival joints any size including fixing to steel pipe 15mm bore union sand joint with adhesive , taflon tape.

S&F in repair stainless steel towel rail long specified and directed by Eng-in-charge.

S&F in Repairs Soap Dish Specified and directed by Eng-in-charge.

S&F in Repairs Toilet paper holder fancy type ,specified and directed by Eng-in-charge.

S&F in repairs glass self 300mm ,specified and directed by Eng-in-charge.

S&F in Repairs angular cock valves regular body with adjustable wall flange 15 mm dia screwed down fixed and joint with adhesive , taflon tape specified and directed by Eng-in-charge.

S&F PVC connections 15 mm size with PTMT nuts of length 450mm

S F Sinks made of stainless steel 1mm thick kitchen or laboratory with plugsm wasers and wastes including bedding in cement mortar on to drarf wall or including ficing cantilever brackets and connecting union to pipe overall size 495 mmx420mm boel siz 410mm x 330mm x 160 mm all as specifie and directed.

S&F Waste fittings,32mm brass , chromium plated for glazed ware sinks , basins , etc. with long screwed shanks and fly -nuts , flange end bedded in red lead cement and other end fixed

S&F bib tap 15 mm bore with crutch or , screwed down,with sink cock swing spout (W/M)with flange .

Taking up or down steel tubing and connections including cleaning for refixing or removal to store of 15 mm dia.

Taking up or down steel tubing and connections including cleaning for refixing or removal to store of 20 mm dia.

S&F CPVC pipe outer dia 16mm SDR 11 & plain CPVC SDR 11 , with all fittings and concealed joint with cpvc Adhesive , taflon tape complete to walls and ceilings or laid in floors including cutting grooves ,filled with cement morter in CM 1:4

S&F CPVC pipe outer dia 20mm SDR 11 & plain CPVC SDR 11 , with all fittings and joint with cpvc Adhesive taflon tape and fixed complete to walls and ceilings or laid in floors

S&F in repairs CP Bib taps long body, cast copper alloy chromium plated with crutch or fancy type, screwed down,and joint with adhesive , taflon tape screwed for iron pipe or for brass ferrule and fixed

S&F 500ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position with 20mm ball/float valve including dismantling of old one complete all as specified.

S&F 1000ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position with 20mm ball/float valve including dismantling of old one complete all as specified.

S&F 25 mm bore Ball brass valves,high pressure,with polythene float and flynut complete, screwed for iron pipe or brassferrule and fixed

S&F in repairs PVC(SWR) pipe 110 mm dia, conforming to IS-13592-1992 type 'B', single socketed in any length with rubber ring joints and pvc adhesive, laid in trenches or in floors.

S&F in repairs PVC(SWR) pipe 75 mm dia, conforming to IS-13592-1992 type 'B', single socketed in any length with rubber ring joints and pvc adhesive , laid in trenches or in floors.

S&F in repairs PVC(SWR) bend any radius, 110 mm dia.

S&F in repairs PVC(SWR) bend any radius, 75 mm dia.

S&F in repairs 75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent.

Demolition brick work /stone masonry built in cement mortar of any description.

M&L brick work with sub - class 'B' bricks straight or curved on plan 6 mtr mean radius built in cement mortar 1:4

Demolition of in lintels, chajja,manole cover landing,stair case of cement concrete reinforced of cimilar suspended works complete all as specifeid

M & L RCC nominal mix type B1 1:2:4 using 20mm graded aggregate as chajja etc and incl necessary formworkall as specified.

S&F TMT bars 10mm dia and over, cut to length, bent to shape required,including binding with mild steel wire (annealed) not less than 0.9mm dia.

Excavation in trenches n.exc 1.5 m wide & n.exc 1.5 m depth for foundations, sewage lines etc and n.exc 10 Sqm on plan for manholes and getting out in soft/loose soil complete all as specified and directed.

Excavation in trenches n.exc 1.5 m wide & n.exc 3 m depth for foundations, sewage lines etc and n.exc 10 Sqm on plan for manholes and getting out in hard/dense soil complete all as specified and directed.

Returning, filling in, including, spreading, leveling, watering and well ramming in layers not exc. 25 cm depth as in any type of soil complete all as specified and directed.

Removing excavated materials to a distance not exceeding 50 m and depositing at a level not exceeding 1.5 m from starting point.

Demolition and breaking up any sewage drain pipe not exceeding 150mm bore dia set in cement mortar including haunching as directed by EIC.

Demolition and breaking up any sewage drain pipe not exceeding 200mm bore dia set in cement mortar including haunching as directed by EIC.

M&L for cement concrete bedding and haunching against the sides of pipes after they are laid to 150mm bore drain pipes in PCC 1:3:6 type C-2 (using 40 mm graded stone aggregates) laid to falls including packing under, and tested, complete all as specified and directed. NOTE :- Pipe shall be measured and paid separately).as in repairs.

M&L for cement concrete bedding and haunching against the sides of pipes after they are laid to 200mm bore drain pipes in PCC 1:3:6 type C-2 (using 40 mm graded stone aggregates) laid to falls including packing under, and tested, complete all as specified and directed. NOTE :- Pipe shall be measured and paid separately).as in repairs.

S&F DWCPE (SN8) pipes, nominal dia 150 mm laid in trenches for sewer network, fixed and jointed with integral socket or coupler and EPDM sealing ring (depending on pipe ends) as per manufacturer instructions complete all as specified and as directed by Engr-in-Charge (Make (DWCPE Pipe) : Supreme, Prince, Berlia or equivalent as specified in Appx B )

S&F DWCPE (SN8) pipes, nominal dia 200 mm laid in trenches for sewer network, fixed and jointed with integral socket or coupler and EPDM sealing ring (depending on pipe ends) as per manufacturer instructions complete all as specified and as directed by Engr-in-Charge (Make (DWCPE Pipe) : Supreme, Prince, Berlia or equivalent as specified in Appx B )

S&F mild steel of grade Fe-290 (Grade E-165) in framed work such as grills, grating etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders; ramed balusters; walk ways; railings; framework of water tanks and similar works.

M & L for preparation of New steel surfaces of any description, over 10cm in width or girth, not otherwise described and apply two coats of synthetic enamel paint over a coat of red oxide zinc chrome.

Demolition for reinforcement cement concrete complete all as specified and as directed.

M&L for precast RCC 1:2:4 type B1 using 20mm graded stone aggregate in cover/plaform slabs including necessary form work etc for manholes Cover/platform,RCC benches set in CM 1:4 (reinforcement measured seperately)

Dismantling of MS work of any description not otherwise provided for complete all as specified and as directed

S& F Hand rails, Half round or other steel section or core for wooden hand-rail straight portion , drilled and countersunk for balusters, nosing to steps including embeding in concrete and screwing etc wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed,drilling holes,notching for wire etc, flat iron fillets (for securing wire mesh etc) including all necessary drilling,bolting or riveting etc and similar work conforming to Fe-290 Gde E-165

S & F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe 410 -W (GdeE- 250) qualityA

S&F MS Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work or of any other section including ornmental CI items for Portions framed and hung as gates, including pintle hinges,stops ,hand-made sliding bolts etc posts and struts in fencing including cutting tops to shape as directed, drilling holes,notching for wire etc,flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting etc and similar work conforming to Fe-290 Gde E-165

Demolition of brick work or stone/boulder masonry built in cement mortor or cement lime mortor incl all quoins,arches,pillars etc all as specified and directed

M&L Pre cast cement concrete block type C1in 1:3:6 Using 20 mm graded stone aggregate exc 10 CM in widdth and setting in CM 1;6 all as specified and directed.

M&L for rendering 15 mm thick in CM 1:4 on the external surfaces of brick work/Stone or concrete surface finishing fair and even without using extra cement.

M&L for preparation of surfaces plastered or unplastered new surfaces on walls and applying two coats of cement base paint over a coat of primer.

M&L PCC (1:3:6) C-2,using 40mm graded stone aggregate in foundation,filling and mass concrete including form work

Dismantling fencing wire mesh any type

Supply only chain link MS Galvanized fencing size or type 75mm x 75mm with 4mm dia wire incl line wire and any type of standarded rails standard bolts incl binding wire (if minimum weight is not available then contractor has to provide next higher weight without extra cost)

Fixing only chain link fencing including line wires,any mesh size and type to any type of standard rails, straining bolts etc incl providing binding wire.

M&L for preparation of new steel surfaces exc 10 cm in width or girth and applying two coats of synethetic enamel paint over a coat of red oxide/zinc primer

Taking down copper /aluminium point wiring (light, fan, bell,socket or power) complete including fixture and fittings such as switches , ceiling roses , pendent , regulators, sockets, light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit a for above items should be made as per condition seperately) and making good distrubed surfaces of walls, floors etc complete all as specified and directed at site.

Taking down old/unserviceable distribution board by disconnection of electric connection carefully SPN DBs/TPN DBs/ Main Switch including old unserviceable MCCBs/ MCBs, Isolators, etc and making good to disturbed surface complete all as specified and as directed by Engineer-In-Charge.

Taking down carefully copper/aluminium Sub main wiring of any size from surface/concealed /existing conduit of any height and removing materials at site and making good disturbed surfaces of walls, floors roofs etc complete all as specified and as directed by Engineer-In-Charge.

Taking down existing geyser of any capacity after disconnecting all necessary electrical and water supply connections and deposit to MES store yard of AGE E/M jamnagar complete all as specified and as directed by Engineer-In-Charge.

Taking down ceiling fan / Exhaust fan of any sweep after disconnecting all necessary electrical connections form ceiling rose to fan, fan blades and deposite to MES store yard of AGE E/M jamnagar complete all as specified and as directed by Engineer-In-Charge.

Taking down existing energy meter from site and deposit to MES store yard and refixing the same meter after completion of work complete all as specified and as directed by Engineer-In-Charge.

M & L for Point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 Sq. mm (nominal area), two single core, PVC insulated and unsheathed FRLSH cable 1100 volts grade ISI-694 marked drawn through in and including heavy duty, PVC concealed conduit of white/ ivory colour including all accessories after chasing in wall/ceiling etc, heavy duty ISI marked, with GI sunken boxes 1.2 mm thick, 60 mm deep with earth dolly duly, covered with modular white cover plate with frame suitable for modular switches, including PVC insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLSH cable as earth continuity conductor to common earth and connecting to earth dolly including cutting, chasses and making goood disturbed surface to mtatch with existing finish with plaster complete all as specified and directed for the following :-

(a) One light point controlled by one, one way switch 5 Amps

(b) One fan point/ exhaust fan point controlled by one, one way switch 5 Amps and regulator

(c) One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

(d) One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent boad.

(e) One bell point controlled by one, bell switch 5 Amps

Description all as per item No 131 here in before but using 2.5 sq mm single core copper conductor FRLSH cable of multistranded PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 2.5 sq mm PVC insulated copper conductor FRLSH cable as earth continuity conductor along with wiring and connecting to the common eath dolly.

Description all as per item No 131 here in before but using 4.0 sq mm single core copper conductor FRLSH cable of multistranded PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 4.0 sq mm PVC insulated copper conductor FRLSH cable as earth continuity conductor along with wiring and connecting to the common eath dolly.

S & F for Modular Switch piano flush type, single pole, one way, and 5/6 Amp single module complete all as specified.

S & F for Modular Switch piano flush type, single pole, one way, and 15/16 Amp single module complete all as specified.

S & F for Modular Socket outlet multipurpose having provision for 3 pin, 5/6 Amp and 2 pin, 5/6 Amp, 2 module piano flush type complete all as specified.

S & F for Modular Switch Socket outlet multipurpose having provision for 3 pin, 15/16 Amp and 3 pin, 5/6 Amp, 2 module piano flush type complete all as specified.

S & F for modular step type fan regulator 100/120 watt 2 module suitable for 230 volt 50 Hz AC supply complete all as specified and as directed.

S & F for for Bell push modular 6 Amps single module complete all as specified.

Suply and fix for Bell Electric Ding dong AC 230 volts type single pole complete all as specified and as directed

S & F for Ceiling rose, surface Bakelite suitable ISI marked for batten fitting complete all as specified

S & F for for Lamp holder, PVC body of brass suitable for batten fitting completes all as specified.

M & L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLSH cable with stranded copper conductor of size 6 Sq mm nominal area and drawing into PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc one run of PVC insulated with 6.0 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and as directed. Note:- Two runs of 6.0 sqmm cable,one run of 6.0 sqmm cable and one run of PVC heavy duty conduit will be measured as one unit

S & F for sheet metal enclosure MCB DB TPN 4 way Vertical type with 200 Amps rated bus bar 415 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

S & F for sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

S & F for MCB tripple pole and neutral rated capacity 63 Amps, 415 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S & F for MCB Single pole and neutral rated capacity 5 to 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S & F for MCB Single pole rated capacity 5 to 32 Amps, 240 V breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S & F for metal clad box suitable for 230 volt 50 Hz AC supply three pin with MCB SP 20/32 Amps including removal of old unserviceable one complete all as specified and as directed complete all as specified and as directed

Fixing only water heater storage type (Geyser) vertical/ Horizental type as per site requirement obtained from item no 128 above with replacement of unsv 3 core PVC insulated PVC sheated multi stranded copper conductor cable and painting of geyser complete with two coats synthetic enamel paint by spraying incuding filling cavities with filler after cleaning all dust etc. complete all as specified and directed.

Labour only for refixing the celing fan obtained from item No 129 above with replacement of unsv 3 core PVC insulated PVC sheated 3 core multistranded copper conductor cable of size 23/ 0.193 from ceiling rose to fan terminal including over hauling the fan, painting of ceiling fans complete with two coats synthetic enamel paint by spraying including filling cavities with filler after cleaning all dust etc. complete all as specified and as directed.

Labour only for refixing the Exhaust fan obtained from item No 129 above with replacement of unsv 3 core PVC insulated PVC sheated 3 core multistranded copper conductor cable of size 23/ 0.193 from ceiling rose to fan terminal including over hauling the fan, painting of ceiling fans complete with two coats synthetic enamel paint by spraying including filling cavities with filler after cleaning all dust etc. complete all as specified and as directed.

S & F for Highly efficient LED Bulbs, 10 watts used as a ready replacement for existing GLS/CFL direct fit lamp, in B-22 cap complete all as specified and directed . Make Bajaj, Havells, HPL

S & F for Decorative wall mounted luminaire made out of polycarbonate with unbreakable globe suitable for LED bulb and including provosion of LED bulb 10 watts complete all as specified and as directed. Make- Havells Cat part No -LHDLO6160099 or its equivalent in Wipro, Philips, Bajaj

S & F for LED tube light fitting with aluminium housing 2 feet x 10 watts mirror type with high out put diffuser, decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose to fitting with warranty option of 5 years from date of installationcomplete all as specified and as directed.Make :- Bajaj or its equvalent in Wipro, Philips, Havells.

S & F for Energy saving new generation 10 watts LED bulk head fitting IP 65 luminaire with opel diffuser pre wired with warranty option of 5 years from date of installation and necessary mounting arrangements , provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting with warranty option of 5 years from date of installation including LED bulb complete all as specified and as directed. Make :- Bajaj Cat No BIBWP 10W LED, Wipro Cat part No LW07-141-XXX-57-G1 or its equvalent in Philips Cat part No WT202W LED6S NW PSU S2 PC.

S & F for wall mounted LED tube light fitting 20 watts batten for surface mounted, anodized extruded aluminium housing, high transmissitivity diffuser, high lumen ouput box type fitting, 230 volts and intregrated electronic driver connector block etc with warranty option of 5 years from date of installation complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed. Make :- Bajaj Cat Part No BCLAB 20W WH LED P or Wipro Cat Part NoLL24R-251-57XX or Philips Cat Part No BN100C LED40S-6500 PSU L120 GR or equivalent of make specified complete all as specified and directed by Engr-in-Charge.

S & F for Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 25/35 watts with pre wired and necessary mounting arrangements and provision of 2.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting with warranty option of 5 years from date of installation including necessary dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as directed by Engineer- in-charge. Make :- Bajaj Cat part No ENXT P 30L WH CR PC SD, or its equvalent in Wipro Cat part No LR02-291-XXX-57-XX, Philips Cat part No BRP042 P LED25 CW SLE S1 PSU GR P4210.

M&L for Earthing complete with galvanised steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground vertically (earth pit not less than 2.25 mtrs below normal ground level) with the top edge of the plate not less than 1.5m below the normal ground level connected to GI wire 4.00mm dia protected by 15mm bore GI pipe light grade) and watering pipe 20mm bore GI pipe (medium grade) and chamber PCC (1:4:8) type D2( using 40mm grade stone aggregate), MS FUNNEL with wire mesh ,coping shall be PCC (1:3:6) type C1 using 20mm graded stone aggregate and RCC (1:2:4) type B1 using 20mm graded stone aggregate, pit cover 50mm thick reinforced with 8 mm MS bar at 80mm c/c both way in lieu of CI pit cover with lifting hook including excavation and earth work and removal of surplus soil complete all as shown in electrical plate No-3 of SSR part-I and as specified including earth plate packed around with charcoal dust common salt complete including GI sheet funnel, wire mesh, earth lead wire 4mm dia and earth lead connected to earthing test point/ main board. The GI earth wire 8 SWG under the earth and on pole/db upto a height of 1.5m shall also be protected by 15mm dia GI pipe (light grade ) and the GI pipe to be fixed with poles/wall by means of 02 Nos. FI clamp 25x3mm with nuts bolts and washer etc. incl taking down old earthing complete all as specified and directed by Engineer-in-Charge. Note :- GI earthing wire 4mm dia and protected pipe 15 mm dia of same size upto 7.5m shall deemed to be included into quoted rate

M & L filling dry and clean sand in trenches for cable 8 cm deep below and 15 cm above for cable cushioning complete all as specified and directed by Engr in Charge.

Supplying and laying un-reinforced precast concrete cable cover, LV low voltage type -I flat size 250 mm x 150 mm x 40 mm complete all as specified and directed by Engr-In-charge.

Material and labour for XLPE insulated screened PVC bedded galvanised steel strip of wire armoured UG heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area of 25 sqmm 4 core size laid in trenches under floor/roads/hard standing along poles etc all as specified and directed by Engr in Charge. (Excavation and earth work, sand cushioning ,brick protection & GI pipe shall be measured and paid for separately).

M & L for GI pipe 40 mm dia Light grade fixing to wall or laying in floors for protection of cable complete all as specified and directed by Engr in Charge.

Taking up and taking down GI tubing and connections 20mm size of pipes including all fitting complete all as specified and directed :-

Taking up and taking down GI tubing and connections 25mm size of pipes including all fitting complete all as specified and directed :-

S&F GI tube medium grade 20mm dia with all fittings laid in trenches complete all as specified and directed

S&F GI tube medium grade 25mm dia with all fittings laid in trenches complete all as specified and directed

S&F Gun metal Gate valve with iron wheel head, screwed both ends for iron pipe and fixed of size 20 mm bore complete all as specified and as directed by Engr in Charge

badri glass and construction (BID ID -3141559)

Prashiv Enterprise (BID ID -3127778)

ABR Trading Co (BID ID -3137705)

S t modi (BID ID -3141937)

JAY DWARAKDHISH ENTERPRISE (BID ID -3142416)