additional toilets along the SD queue lines, Tirumala

Demolishing and disposal of unserviceable materials with in 100 metres lead Unreinforced cement concrete up to 15cm thickness

Demolition including stacking of serviceable materials and disposal of unserviceable materials within 100 metres lead-R.C.C.work

Demolishing and disposal of unserviceable materials with in 100 metres lead Unreinforced cement concrete more than 15cm thickness

Cutting road surface including stacking of excavated materials for pipe line trench work.-do- cutting open B.T Road surface (as well as asphalt concrete up to 75 mm thick) including water bound mecadam.

Earthwork excavation for foundations and depositing on bank for all lifts and with an initial lead of 10m including all Operational, incidental ,labour charges such as shoring, sheeting, planking, strutting etc., complete for finished item of work. Ordinary soil-Mechanical means up to 3m depth

Earthwork excavation for foundations and depositing on bank for all lifts and with an initial lead of 10m including all Operational, incidental ,labour charges such as shoring, sheeting, planking, strutting etc., complete for finished item of work. Ordinary soil-Manual means up to 3m depth

Earthwork excavation in hard rock (blasting prohibited) with rock breakers including breaking rock, loading in tippers and disposal with intial lift of 3 m and lead up to 1000 mt, including trimming bottom and side slopes in accordance with requirements of lines grades and cross sections as per technical specifications clause 302.3.5 MORD/301 MORTH - Mechanical means.

Note: 1 1. The quality, quantity and availability of rock shall be checked before affording credit. 2. In case some rock is issued to the contractor, rate as arrived per cum to that issued extent shall be deducted. 3. In case some rock is issued to the contractor at site , the item carriage shall be restricted / reduced to that extent. 4.Being small quantity, manual loading will be economical in this case and has been provided accordingly.

Filling with useful available excavated earth (excluding rock) in trenches, sides of foundations and basement with initial lead in layers not exceeding 15cm thick, consolidating each deposited layer by watering and ramming including cost and conveyance of water to work site and all operational, incidental, labour charges, hire charges of T&P etc., complete for finished item of work.

Note: Cost of transportation of good quality earth has not been included. Only labour for carrying carted earth with a lead of 50m to the foundation pits has been taken in the rate. The cost of carted earth / sand may be worked out separately if the same is not available from adjoining area.

Conveyance of excavated surplus earth/debris to a distance 2 kms from the site of work at the place specified by the Engineer-in-Charge including loading and unloading etc., complete as directed during execution.

Filling of foundations and basement with best river sand in layers of not more than 15 cms. thick each well watered to saturation and consolidated including cost and conveyance of all materials, incidental charges etc., complete.

Cement Concrete (1:4:8) using 40 mm ( 0.54 Cum), 20 mm (0.27Cum) and 12 mm (0.09Cum)nominal size hard broken granite crushed metal from any source conforming to the relevant ISI standards for foundations etc., laid in layers of not more than 15 cm thick well compacted including curing, machine mixing cost and conveyance of all materials etc., complete.

Cement Concrete (1:2.5:5)-Grade M15 using 20 mm ( 0.54 cu.m) and 12 mm (0.36cu.m) nominal size hard broken granite crushed metal from any source conforming to the relevant ISI standards for foundations etc., laid in layers of not more than 15 cm thick well compacted including curing, ,machine mixing, cost and conveyance of all materials etc., complete. Note: Measurement boxes shall be used for measuring the quantities of cement, aggregate and water required for the given concrete mix.

Supply and placing of M 25 Design Mix Concrete corresponding to IS 456 using concrete mixer using of 20 mm HBG crushed metal 0.530 cu.m (707 kg),. 10 mm HBG crushed metal, 0.362 cu.m (471 kg) , sand 0.407 cu.m (616 kg.) and cement 380 kg with water cement ratio of 0.48 ( 182.40 ltrs/ cu.m of CC) etc., to site and including sales & other taxes on all materials including all operational, incidental and labour charges such as machine mixing, vibrating, laying concrete, curing etc., complete with cement from standard suppliers approved by the department , including cost of centering, shuttering charges but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402).

Note : The design mix shall be got designed by furnishing the information required as per clause 19.1.1 &19.1.2 of IS 456-2000 by the contractor at his own cost and get approved from the competent authority before execution. The cement considered for above M25 grade concrete is 380 kg/cu.m and the rate is arrived accordingly in the estimate. After the mix is designed and approved, if there is any variation in the quantity of cement, over the cement content adopted in the estimate, the same will be considered and paid/recovered at estimate rate + T.P ( Either increase or decrease in quantity adopted in the estimate). Payment will not be made for variation in the quantity of other materials such as coarse & Fine aggregates.

-do- For footings

-do- Columns up to Basement

-do for Plinth Beams

-do- Columns in First Floor

Supply and placing of M 25 Design Mix Concrete corresponding to IS 456 using concrete mixer using of 20 mm HBG crushed metal 0.530 cu.m (707 kg),. 10 mm HBG crushed metal, 0.362 cu.m (471 kg) , sand 0.407 cu.m (616 kg.) and cement 380 kg with water cement ratio of 0.48 ( 182.40 ltrs/ cu.m of CC) etc., to site and including sales & other taxes on all materials including all operational, incidental and labour charges such as machine mixing, vibrating, laying concrete, curing etc., complete with cement from standard suppliers approved by the department but excluding cost of centering, shuttering charges and excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402). -do- For R.C.C Slabs

Note : The design mix shall be got designed by furnishing the information required as per clause 19.1.1 &19.1.2 of IS 456-2000 by the contractor at his own cost and get approved from the competent authority before execution. The cement considered for above M25 grade concrete is 380 kg/cu.m and the rate is arrived accordingly in the estimate. After the mix is designed and approved, if there is any variation in the quantity of cement, over the cement content adopted in the estimate, the same will be considered and paid/recovered at estimate rate + T.P ( Either increase or decrease in quantity adopted in the estimate). Payment will not be made for variation in the quantity of other materials such as coarse & Fine aggregates.

HIRE CHARGES FOR CENTERING & SCAFFOLDING - Unsupported height up to 3.66 m - Steel scaffolding pipes , jack props, wallers, Foot plates , brackets, steel centering plates, etc., for SLABS up to 150mm thick

Hire charges for Centering and Scaffolding charges for VCC "Vertical walls of plane surface (rate is for both sides centering) including open drains. Note : The centering charges for VCC vertical walls are both the faces of the repsective members. The measurement of centering charges shall be in Sqm for one face only and the centering charges given are for two faces of centering

Providing High Yield Strength deformed (HYSD)/ Thermo mechancially treated (TMT) steel bars of specified grade (as per IS 1786 - 2008) of different diametres for RCC works, including labour charges for straightening, cutting, bending to required sizes and shapes, placing in position with cover blocks of approved materials and size and tying and lap splicing with binding wire of 18 SWG, forming grills for reinforcement work as per approved designs and drawings, including cost and conveyance of steel bars including all wastages such as over laps, couplings, chairs, spacer bars including cost and conveyance of binding wire, cover blocks and all incidental, operational, labour charges such as cutting, bending, placing in position, tying including sales and other taxes on all materials etc., complete for finished item of work in all floors. (APSS NO.126) (In the absence of 18G binding wire,2 nos of 20G binding wire in tandem are to be strictly adhered). -do- below 36 mm Fe 500/Fe-500D/Fe550 Note: Unless otherwise fabrication and placement of steel, no pre-pament shall be made against the supply of steel reinforcement

Construction of Brick Masonry in CM(1:6) using well burnt Bricks 2nd class or ground moulded (Non- modular or traditional size) (230 x 110 x 70 mm) including curing, cost and conveyance of all materials as directed during execution and complying with standard specifications etc., complete.

Construction of 110 mm thick Brick masony in C.M (1:5) for super-structure using second class traditional size bricks (23X11X7CM) including cost of all materials, seigniorage charges, labour and all operations for constructing half brick masonry, mixing cement motar, curing etc., complete - for finished item of work.

Plastering in Cement mortar (1:5) 20 mm thick using best river sand from approved quarry including cost and conveyance of all materials, screening, curing, rounding of corners, incidental charges as directed during execution complying with standard specifications etc., complete.

Plastering in Cement mortar (1:5) 12 mm thick using best river sand from approved quarry including cost and conveyance of all materials, screening, curing, rounding of corners, incidental charges as directed during execution complying with standard specifications etc., complete.

Flooring with cement concrete floor tiles of 25 mm thick confirming to IS 1380-12013/IS 1237-2012 of following sizes set over base coat of cement mortar (1:6) 20 mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3 kgs per sq.m & jointed with neat cement to full depth mixed with pigment of matching shade including cost & conveyance of all materials, etc., complete for finished item of work. (Note: Unless otherwise laying of flooring is finished, no pre-payment shall be made for the tiles against supply) High strength cement concrete plain step tiles with edge half rounded and grooved confirming to IS:1237 using aggregates, cement, pigments of regular colour, design and of 25 mm thickness.

Providing skirting to internal walls to 15 cm height / risers of steps with cement concrete floor tiles of 25 mm thick length equal to flooring stones, set over base coat of CM (1:3) 12 mm thick with cement slurry of honey like consistency spread at the rate of 3.30 kgs per sq.m and jointed with white cement paste mixed with pigment of matching shade to full depth, including cost and conveyance of all materials like tiles, cement, sand and water etc., complete for finished item of work. High strength cement concrete plain step tiles with edge half rounded and grooved confirming to IS:13801 using aggregates, cement, pigments of regular colour, design and of 25 mm thickness.

Flooring with cement concrete floor tiles of 25 mm thick confirming to IS 1380-12013/IS 1237-2012 of following sizes set over base coat of cement mortar (1:6) 20 mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3 kgs per sq.m & jointed with neat cement to full depth mixed with pigment of matching shade including cost & conveyance of all materials, etc., complete for finished item of work. (Note: Unless otherwise laying of flooring is finished, no pre-payment shall be made for the tiles against supply). -do - Chequered cement concrete heavy duty tiles confirming to IS:13801 using aggregates, cement, pigments of size 300 X 300 x 25mm of any shades.

Providing skirting to internal walls to the following heights / risers of steps with vitrified tiles length equal to flooring stones, set over base coat of CM (1:3) 12 mm thick with cement slurry of honey like consistency spread at the rate of 3.30 kgs per sq.m and jointed with white cement paste mixed with pigment of matching shade to full depth, including cost and conveyance of all materials, etc., complete - for finished item of work. -do- Supply of Double charged / multi charged stain free full body porcelain vitrified tiles with double layer pigment of size 600 x 600 mm and thickness between 8-10 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs

Flooring with telephone Black Granite 18-20 mm thick upto 2.43 M set over base coat of cement mortar (1:8) 20 mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3 kgs per sqm & jointed neatly with white cement paste mixed with pigment of matching shade to full depth, including cost & conveyance of all materials, seigniorage charges, labour charges for dressing of tiles etc., complete for finished item of work. (Note: Unless otherwise laying of flooring is finished, no pre-payment shall be made for the slabs against supply)

Flooring with granite slabs set over base coat of cement mortar (1:8) 20 mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3 kgs per sqm & jointed neatly with white cement paste mixed with pigment of matching shade to full depth, including cost & conveyance of all materials, seigniorage charges, labour charges for dressing of tiles etc., complete for finished item of work. - do - Galaxy granite 18-20 mm thick upto 8'-00(2.43 m) (Premium Quality)

Flooring with Antiskid floor tiles 1st quality of all series & shades (as per manufacture specification), set over base coat of cement mortar (1:6) 20 mm thick over CC bed already laid or RCC roof slab, including white cement slurry of honey like consistency spread @ 3.30 kgs per sq.m. jointed with neat cement to full depth mixed with pigment of matching shade, including cost and conveyance of all materials like flooring slab, cement, sand and water etc., complete, for finished item of work. (Note: Unless otherwise laying of flooring is finished, no pre-payment shall be made for the tiles against supply)

- do - Supply of Non-skid red or white full body Ceramic floor tiles of size 450 x 450 mm and thickness between 7-8 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs

Finishing the sides of walls with Ist quality glazed wall tiles of following sizes of approved colour and brands including pointing the joints with the same colour of cement by mixing the same colour pigment in white cement and over a bed of C.M.(1:3), 12 mm thick & Cement slurry of 33 Kg /10 sq.m shall be used for fixing bed tiles including cost and conveyance of all materials, curing, incidental charges etc., complete (No separate plastering shall be paid to the walls). (Note: Unless otherwise laying of flooring is finished, no pre-payment shall be made for the tiles against supply)

Supply of glazed red or white full body ceramic wall tiles of size 300 x 600 mm and thickness between 6-8 mm 1st quality conforming to IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and finish in all shades and designs

Half Rounding the edges of Marble/ Granite stone slabs of all thicknesses including polishing the same

Supply fixing and fabrication of MS hollow tubes & pipes of all diametres as per IS-1161 of approved design including Labour charges for fabricating all heavy steel works like Trusses, Stanchions, Heavy Beams and Girders including cost of welding rods, power charges, etc including Labour charges for fixing heavy iron grills, Trusses, Stanchions, Heavy Beams and Girders erecting in position and fixing by using chain pulley blocks, Derek pole arrangements and cranes etc., complete in position including painting the same with Two coats of Synthetic enamel paint over a Primary coat (Red oxide metal primer) (total three coats) of approved make and colour including cost of making the holes into RCC or masonry works and making good the same wherever necessary, including cost and conveyance of all materials as directed during execution.

Supplying , fixing and fabrication in position M.S tubes & pipes of all diameters as per ISI 1161 of approved size design including Labour charges for fabricating all heavy steel works like Trusses, Stanchions, Heavy Beams and Girders including cost of welding rods, power charges, etc., including labour charges for fixing iron doors, iron windows and window grills in positionn including painting the same with Two coats with Synthetic enamel paint over a Primary coat (Red oxide metal primer) (total three coats) of approved make and colour including cost of making the holes into RCC or masonry works and making good the same wherever necessary, including cost and conveyance of all materials, incidental charges etc., complete.

Supply, Fabrication and fixing of Mild steel base Plates of diffrent sizes including cost and conveyance etc complete as directed during the execution of the work including Labour charges for fabricating all heavy steel works like Trusses, Stanchions, Heavy Beams and Girders including cost of welding rods, power charges, etc including cost of fixing in position including painting the grills with two coats of with synthetic enamel paint over a red oxide metal primer paint (total three coats) grade -1 of approved make and colour etc., complete as directed during the execution of the work.

Supply and fixing of Galvalume sheet Pre-painted Galvalume Trapezoidal Profile Roofing sheets with 0.47mm thickness (Total Coated Thickness-TCT), Coating: Alu-Zinc coating AZ150 GSM. Tensile strength: 550 MPA. Paint coating: Regular Modified Polyester painting. Painting thickness (Top): 18 to 20 Microns, (Bottom): 5 to 7 Microns. Sheet Width: 1.020, Length: Maximum 12 Meters with Regular Range Colours with minimum end lap of 15 cms etc.,complete as directed during execution (Original coil shall be of make TATA Blue scope/JSW)

Supply of roof accessories medium size ridge, barge cap corner trim, L-Flashing, down pipes, gutter etc., with 0.47mm thick, width:0.585, Length maximum 2.50 mts.

Providing and applying wall putty of white cement or polymer or cement based putty of approved make with average 1 to 2 mm thickness over plastered surface to prepare the surface even and smooth after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, applying emery paper, sand the surface, clean & wipe off loose dust, applying knifing paste filler by putty knife / muslin pad, air dry for 2-3 hrs. sand with 180 and 320 No., emery paper for the surface preparation including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work, excluding scaffolding charges - for internal and external walls.-do- for new work

Painting two coats with Acrylic Emulsion paint exterior grade with silicon additives having VOC (Volatile Organic Compound) content less than 50 grams/liter of approved brand and shade over cement primer exterior grade-2, (total three coats) after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work as per SS 911for new external walls.

Painting two coats with Acrylic Emulsion paint interior grade having VOC (Volatile Organic Compound) content less than 50 grams/liter of approved brand over primary coat (total three coats) using ready mixed cement primer (water thinnable) for interior grade-1 (total three coats) and shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials, including cost and conveyance of all materials to work site and all operational, incidental, labour charges etc., complete for finished item of work as per SS 911 for internal walls New work

Supplying and fixing in position M.S Ornamental grills for windows and ventilators or for veranda openings using M.S. Flats, square rods, angles sheets etc., of approved design including necessary cuttings, bending fabrication, welding, grinding and finishing smooth including painting the grills with Two coats with Synthetic enamel paint Gr-I over a Primary coat (Red oxide metal primer) (total three coats) of approved make and colour including cost of making the holes into RCC or masonry works and making good the same wherever necessary, including cost and conveyance of all materials, incidental charges etc., complete.

Supply and fixing of stainless steel SS-304 grade tubes, sections, plates , sheets and pipes of all sizes and diameters etc., including cost and conveyance of all materials and labour charges for fabrication of stainless steel railing works using SS welding rods including buffing , polishing , lacquer finishing , to present seamless finishing etc., complete as directed during execution

Providing and fixing 28 -30 MM thick solid Wood Polymer Composite(WPC) single extruded door shutter with 3MM top and bottom rigid layer with an overall density of 750kg/Cum. It will be fixed to the frame using 3 inch /4 inch hinges. Minimum of 4 hinges will be required for fixing the door with the frame

Providing and fixing factory made solid Wood Polymer Composite (WPC) single extruded Door Frame section of size with encapsulation of 8MM rigid layer on all the six surfaces. The door frame will have a rebat of 32MM.

Door Frame section of 45x75 MM . The two Vertical members are to be joined together with the horizontal member using 8x50 MM long MS Star full thread screws to be used with reverse forward speed control hand drilling machine. The ready/assembled door frame is fixed to the wall using hold fast or bolt fasteners. A minimum of 4 No.s of screws to be provided for each vertical member & minimum 2no.s for horizontal member.

Supplying & Fixing Orissa Pan white glazed W.C 1st quality ISI marked conforming to IS:2556-Part-3-1981 with "P" or "S" trap 580x440 mm ISI Mark or equivalent brand approved by the department.

Supplying and Fixing European Water Closet of 1st quality confirming to IS:2556-Part-2-1973 of white glazed with 'P' trap with ISI mark or equivalent brand approved by the department.

Supply & fixing of PVC low level cistern with internal components & short bend: 10 Litres capacity Single Flush

Supplying and Fixing best Indian make plastic seat and lid for European water closets with rubber or plastic Buffers as per IS 2548-1996

Supplying & Fixing white glazed flat back half stall urinals 590 x 375 x 390 mm 1st quality confirming to IS:2556-1995 with standard C.P. Spreader of overall size 95 x 95 x 57 mm confirming to IS:2556 - Part 6, Sec-6-1974 fixed with screws complete Indian make with ISI mark or equivalent approved by the department.

Supplying & fixing oval shape basin white (520x410mm)parry or equivalent

SYMET 2 in 1 Faucet (1 mts tube ) with hook ( prayag make CAT NO 187) as directed during execution

supply and fixing 12.7mm heavy duty dia high neck pillar cock 1st quality Indian make 400 grams

Supply & fixing Waste coupling Jaquar make Chrome finish with 7 years warranty.

SYMET BIB COCK (CAT.NO:125) (20mm) 3/4'' size with flange deluxe handles, 98mm long and 114mm high and 48mm breadth 18mm seat dia and replaceble washers, having approx. weight of 125gms.

Supply & fixing of N.P coat hook

Supply and Fixing of Premium make CPVC Pipes and Fittings to meet the requirement of ASTM-D 2846 and are produced in CTS (Copper Tube Sizes 1/2" ton 2" SDR 11 and SDR 13.5 pipes are made from idential CPVC compounds having the same physical Properties for Hot and Cold Water (IS 15778:2007).

54.00 mm OD pipe SDR - 13.50

28.60 mm OD pipe SDR - 13.50

22.20 mm OD pipe SDR - 13.50

Supplying and fixing Gunmetal Gate (GM peet) valve as per IS - 778 Class-I, Indian make heavy type

-do - 50mm NB Size

- do - 25 mm NB size.

Supply of round jalli

4" (101.6mm) Nahany Trap [without jali with inlet ]

Supplying, laying and jointing in position the following dia metre of PVC/ SWR pipes & fittings ( as per ISI standards) 6Kg/sqcm (Type -B) including labour charges for laying, fixing and commissioning the PVC pipes including couplers/ bends/ tees etc.,any dia including fixing necessary fiittings like bends, plugs, couplers, junctions, tees, etc., with solvent jointing as per standard practice.

160mm dia pipe double Socket

110mm dia pipe Single socket

75mm dia pipe single socket

Supply and fixing of 10 mm wide PVC edge beading including cost and conveyance of all materials and incidental charges, etc., complete.

Supplying and fixing in position 600 x 450 mm size wall mirror with 5 mm thick glass (Saint Gobion) with 6 mm plywood IS 303 bwr (both sides commercial) back in position with 12 mm Aluminium 'U' channel (Jindal make) including cost and conveyance of all materials etc., complete

Manufacture as per BIS:12592 (Part 1&2) Supply & Delivery of Pre-cast concrete manhole covers and frames with ISI marking anywhere in A.P.,F.O.R. destination including, loading, unloading & stacking at site but excluding all taxes.Heavy Duty.-10 with 560mmdia clear opening

Supply of the following Anodized Aluminum Fixtures for Doors and windows

Anodized Aluminum Tower Bolts 10mm dia X 150 mm Long with ISI Mark IS:204

Anodized Alluminium Aldrops sliding door bolts 16 mm x 200 mm (3T-Pieces)

Anodized Aluminium Door Handles (IS:208) 150 mm long

Supply of glow sign vinyl stickered name plate / sign (or) instruction boards using 4mm ACP (Aluminum composite panel )sheet as back ground and glow sign vinyl sticker one layer for letters of different sizes as directed during execution including cost of ACP sheet, vinyl sticker and all labour charges for computer design and cutting, pasting and fixing the boards as directed during execution .

Supply M S Bolts / Nuts / Washers etc.,complete as directed during execution.

Supply of U.V resistant UPVC SWR pipe fittings (as per BIS standards )

110mm dia plain bend 87.5 Degree

110mm dia door bend 87.5 Degrees

110mm dia 45 degree bend

110mm dia Single 'Y'

110mm dia Coupler

110 mm dia Vent Cowl

110 mm dia Single Tee

110 mm dia Single Tee (With Door)

75mm dia plain bend 87.5 Degree

75mm dia Door bend 87.5 Degree

75mm dia Single Tee

75mm dia Single Tee (with Door)

75mm dia 45 Degree bend

75 mm dia single Y

75mm dia Single 'Y' (with Door)

75mm dia COUPLER

75mm dia VENT COWL

Electrical items

Supply and Fixing of ISI mark 25mm outer dia heavy grade (2.20mm thickness) with IS:9537 part -3 P.V.C. pipe for concealed wiring in walls of brick building duly cutting them to the required depth wherever necessary and fixing the pipes and specials with nails and plastering neatly with cement mortar and colour washing to match the finished surface and for surface wiring on chromium plated metallic base saddles on ceiling of roof / existing brick building walls, columns, beams, roofs / trusses / channel etc., and masonry work for light, fan and separate plug point including all labour charges etc., complete. Makes: Sudhakar / Finolex / Polycab / Kumar / AKG / Indian-tubes / GM / Anchor / Nandi / Polyline / Gold Medal

Supply and wiring with 3 run of 14/0.3mm (1.0 sq.mm) PVC insulated FRLS flexible copper cable (ISI MARK) as per IS:694 / 1990 specification in existing PVC pipes / casing & caping with 3 plate pilot ceiling rose, 6 Amp 1 Way Module Modular switch to switch control box including all labour charges etc., complete for Light, bell, fan and Exhaust fan points in Non-Residential Buildings. Grade-A: Wire Makes: Finolex / RRKabel / Havells / Polycab / L&T / KEI Grade-A: Modular Switch Makes: Legrand Arteor / Schneider Zen cello / Gold Medal / GIFA / L&T englaze / Crabtree - Murano / Amare / Ducor / GM Four-Five

Supply and run of 3 wire of 36/0.3mm (2.5 Sq mm) PVC insulated flexible FRLS copper cable as per IS:694 / 1990 specification in the existing PVC pipe / MS pipe /PVC Trunking for mains including all labour charges etc., complete. Grade-A: Makes: Finolex / RRKabel / Havells / Polycab / L&T / KEI

Supply and run of 3 wire of 56/0.3mm (4.0 Sq mm) PVC insulated flexible FRLS copper cable as per IS:694 / 1990 specification in the existing PVC pipe / MS pipe /PVC Trunking for mains including all labour charges etc., complete. Grade-A: Makes: Finolex / RRKabel / Havells / Polycab / L&T / KEI

Supply and fixing of 16 /20 Amps 1 Way 1 Module Modular Switch on to the existing metal box (Switch Control Box) cover frame and giving necessary connections including all labour charges etc., complete. Grade-A: Makes: Legrand Arteor / Schneider Zen cello / Goldmedal (GIFA) / L&T englaze / Crabtree - Murano - Amare - Ducor / GM Four-Five

Supply and fixing of 20 Amps 2 Module Modular Socket with Shutter on to the existing metal box (Switch Control Box) cover frame and giving necessary connections including all labour charges etc., complete. Grade-A: Makes: Legrand Arteor / Schneider Zen cello / Goldmedal (GIFA) / L&T englaze / Crabtree - Murano - Amare - Ducor / GM Four-Five

Fixing of given (9" to 24") Exhaust fan on to the existing hole and giving necessary connections complete.

Supply and fixing of 12 Module Hot Dip Galvanized 20 / 18 SWG Module box with earthing terminal concealed in wall with all required accessories including masonry work and all labour charges etc., complete. Make: Legrand / G.M / L&T / GM Four-Five / Legrand Arteor / Schneider / Anchor / Clipsal / Havells / ABB / Indo Asian / Siemen / Fortune Art.

Supply and fixing of 12 Modular Vertical Cover Plate & Frame on to the Existing Metal Box (Switch control Box) including all labour charges etc., complete. Grade-A: Makes: LegrandArteor / Schneider Zen cello / Goldmedal (GIFA) / L&T englaze / Crabtree- Murano - Amare - Ducor / GM Four-Five

Supply and fixing of 8 Modular Horizontal / Vertical Cover Plate & Frame on to the Existing Metal Box (Switch control Box) including all labour charges etc., complete. Grade-A: Makes: LegrandArteor / Schneider Zen cello / Goldmedal (GIFA) / L&T englaze / Crabtree- Murano - Amare - Ducor / GM Four-Five

Supply and fixing of 8 or 9 Module Hot Dip Galvanized 20 / 18 SWG Module box with earthing terminal concealed in wall with all required accessories including masonry work and all labour charges etc., complete. Make: Legrand / G.M / L&T / GM Four-Five / Legrand Arteor / Schneider / Anchor / Clipsal / Havells / ABB / Indo Asian / Siemen/ Fortune Art.

Supply of 12" (300mm) Light duty exhaust fan with metallic blades and wire guard etc complete. Makes: Crompton / Bajaj Bahar WG / Havells Ventil Air-DSP / Orient hill air/ Halonix / Polycab/G.M. (Xenix)/ Goldmedal (Rapido-12)

Supply and fixing of 20-24W, not less than 1100mm length LED batten light with extruded aluminum housing and polycarbonate cover, input voltage AC 220 - 260 Volts, with high power LEDs, having System Efficacy of >=100 lumens/watt , PF>0.9, Surge protection: 2KV, THD<15%, with inbuilt driver and frosted cover CCT: 3000K - 5700K, minimum CRI>70, etc., complete with earth connection and not less than two years warranty a) LUMINAIRE MAKE : Phillips / GE- Venture / Crompton / Wipro / Bajaj / Havells / Halonix/Jaquar/HPL/GM / GreenLites / Gold Medal/Eveready// Rhino/Panasonic b) LED MAKE : PHILIPS LUMILEDS / CREE / NICHIA / OSRAM / SAMSUNG/ Everlight.

Supply and transportation of 45W LED Street light Luminaire made of pressure diecast aluminum body with powder coated, having protective toughened glass, supply input voltage 120 - 270V AC, P.F > 0.90, high power LEDs having System Efficacy >=120 lumens/watt and junction temperature < 70°C, with Ingress protection IP66, Luminaire performance complies to IS 10322 (Part 5/Sec-3), driver surge protection 4KV, in-house additional Surge protection 10 KV with optics distribution, THD<10% at 110 Volts AC, driver efficiency >90%, CCT: 3000K - 5700K, minimum CRI>70, etc., complete with earth connection and not less than two years warranty.

a) LUMINAIRE MAKE : Wipro(Skyline) / Philips (Green line) / GE-Venture / Crompton(Neo Series) / Bajaj (Edge) / Halonix(Lumos - Super) / Havells (Endura Series) /Capart(Premium)/Greenlites(Hi-Lux) /Polycab/Keselec/ HPL(City Vision)/ Jaquar(Premium)/Eveready/ Surya (Pollux) / FortuneArrt (Leaf) / Rhino(GPSL04) b) LED MAKE : PHILIPS LUMILEDS / CREE / NICHIA / OSRAM / SAMSUNG / LG

Supply & fixing of 1" dia 'B' class GI pipe not exceeding 1.5Mtr long with necessary bending (120° to 135°) to the wall or to the pole as directed during execution duly grouting 2 Nos. of MS angle of 35x35x5mm having length 20Cm (grouted portion of MS angles into the wall 7.5cm) and fixing with 2 Nos. of MS clamps fabricated with 25mmx3mm MS flat with suitable holes and 4 Nos. of 3/8"x2" MS bolts, nuts & washers for fixing on the wall / 2 Nos. of suitable MS clamps with bolts, nuts for fixing to the pole etc., complete. A 16Amp fuse unit is to be fixed to the MS angle / clamp and giving necessary connections with 14/0.3mm PVC copper flexible wire from pole to the fuse unit and to the fitting or from Ceiling rose in the building to the fuse unit and to the fitting with link clips etc., and the GI pipe has to be painted with two coats of enamel grey paint over one coat of red oxide paint. Fixing charges for stem pipe including the cost of MS angle, MS clamps, bending of pipe, bolts, nuts, fuse units etc.

Supply and fixing of 8 Way SP & N Distribution board as per IS 8623; IS 13032; IEC 61439-3 with IP-43 protection (Metal door) firmly concealed in the wall with neat plastering etc., complete. Grade-A: Make: Legrand (Ekinox 3) / Schneider-Acti9 / Hager - Novello+ / Seimens / Havells STADx / L&T-Newrang / Indoasian (Opti Pro)

Supply and fixing of 6 to 32 Amp TP MCBs 10 KA breaking capacity 'C'/ 'D' Curve ISI Mark as per IS:60898-1:2002 in the existing board and giving necessary connections. Grade-A: Makes: Legrand DX3 / Schneider-Acti9 / Hager - Novello+ / Seimens / Havells STADx / L&T- Newrang / Indoasian (Opti pro).

Supply and fixing of 6 to 32 Amps range S.P MCBs 10 KA breaking capacity 'C'/ 'D' Curve ISI Mark as per IS:60898-1:2002 in the existing board and giving necessary connections. Grade-A: Makes: Legrand DX3 / Schneider-Acti9 / Hager - Novello+ / Seimens / Havells STADx / L&T- Newrang / Indoasian (Opti pro).

Supply and transportation of 16 Sq.mm 4 core LT XLPE insulated, 1100V grade armoured Aluminium UG cable as per specification confirming to IS:7098 (Part-I) / 1554-1. Grade-A: Make: Torent / Universal / Unistar / Havells / KEI / Gloster / Polycab / RR Kabel / Finolex.

Laying of U.G cables upto 50 Sq.mm and back filling of trench including labour charges etc., complete.

Supply and making end termination with heavy Alluminium lugs (pin / ring type) upto 16 Sq.mm cable as per IS specification duly crimped with crimping tool, PVC tape etc., complete. Make: Dowels / Jainson / Comet.

Supply and making one end termination with heavy duty single compression brass gland as per BS 6121:2005, IP 66 complete, SIBG type, heavy duty Alluminium lugs duly crimped with crimping tool, PVC tape etc upto 16 Sq.mm with brass washers of Armoured PVC insulated & PVC sheathed / XLPE aluminium conductor cable of 1100 volt grade as required of size. Make: Dowels / Comet / SMI

Earth Work excavation for trench for laying of U.G. Cable in ordinary Soils, manual means to the required width and depth and depositing the same on bank as directed during execution etc., complete .

Supply and fixing of fabricated M.S clamps made out of 25mm x 3mm MS flat with necessary holes on either side with 1 1/2" coach screws and painting 2 coats of enamel black paint over one coat of red oxide suitable for fixing of UG Cables of size 10 Sq.mm to 16 Sq.mm on walls etc. including all labour charges etc., complete.

Providing earthing as per IS 3043/ 1987 with 100mm (ID), 13mm thick C.I. Pipe of 3.0 mtr. length after excavating an earth pit of size1.5 m X 0.9 M X 3.00M(Top 1.50 m X 1.20 m X 0.9m & bottom 1.20 M X 1.20 M X 1.65 M) and filling with a homogenous layer of 40 Kgs. of Coke / Char Coal, 20 Kgs. of Salt and the required quantity of sand around 100mm pipe from the bottom of the pipe to a height of 2.7mtr. and filling the remaining excavated portion with earth and consolidation / Settlement of the trench should be done by filling with sufficient quantity of water. A concrete bed of size 0.8 M X 0.8 M X 0.1 M thick and an inspection chamber having inside measurements of 0.4 M X0.4 M X 0.4 M with wall thickness of 100 mm with cement concrete CC (1:2.5:5) using 20 mm HBG Metal is to be constructed with side wall 100 mm above ground level and plastering the exposed walls neatly with CM (1:3) with 12 mm thick

The Top of the Inspection Chamber is to be provided with reinforced precasted RCC Slab with 40mm thick with lifting hook. The top of C.I. Pipe is to be fixed & welded with suitable G.I. Wire mesh funnel 50mm x 6mm G.I. Strip having length of 300mm is to be fixed to the top of C.I. Pipe with

G.I. Clamps fabricated with 50 x 3mm G.I. Flats with necessary bolts and nuts and necessary welding to be done to the clamps and C.I. Pipe. 2 Nos. of holes are to be drilled on either side of G.I. Flat for Extending earth connections. 65mm dia PVC Pipe is to be embedded at the pit entry for earth.

After laying earth from earth conductor bus to Electrode trough PVC Pipe, the surface should be covered with bitumen and grease. The cost of GI/Copper flat to be run from CI Pipe electrode to the equipment is to be made separately on running meter basis. The work shall be executed strictly as per IS 3043 - 1987. The rate includes cost and conveyance of all materials, labour charges, incidental charges etc., complete (Note:- Necessary meggaring testing is to be carried out in the presence of concerned Engineers and measurement of resistance shall be as per ISI standards)

Supply and run of ' 8 ' SWG G.I wire for earth electrode to required places by Surface in walls, flooring including cost of all accessories and giving necessary connection with 3/8"x2" GI Bolts, Nuts and Washers wherever joints has to be done. The strip has to be either rivited (or) bolted (or) gas welding neatly and all labour charges etc., complete.

Supply and fixing of fabricated M.S clamps made out of various sizes of (25mm x 3mm, 25mm x 6mm etc.) MS flat with necessary holes on either side with suitable MS bolts and nuts and painting 2 coats of enamel black paint over one coat of red oxide suitable for fixing of PVC pipes, Conduit pipes etc., on Trusses / Channels etc. including all labour charges etc., complete.

Fixing of M.V / S.V / M.H luminaire /LED/ Halogen fitting on wall / pole cross arm / channel / stem pipe etc., including all labour charges and giving connections etc., complete.

Supply and fixing of RCCB Up to 40A Four Pole, 30mA for earth leakage protection, confirms to IEC:61008 and IS:12640-1 in the existing boards including internal connections and Labour charges etc., complete. Grade-A: Makes: Legrand DPX3 / Schneider-Acti9 / Hager - Novello+ / Seimens / Havells STADx / L&T- Newrang / Indoasian (Opti pro).

Supply of 225 X 295 X 122 Sizes thermo-plastic cable junction boxes with IP66/67 weatherproof, for outdoor installation with knockouts for cable entry including terminals etc., complete (sizes in mm). Make : Hensel/Sadhrish

Rupees Four Crore Fifty Five Lakh(s) Sixty Two Thousand Two Hundred Forty And Paise Sixty Six Only