BID DOCUMENT FOR CONSTRUCTION OF URBAN HEALTH CENTER AT MANJIPURA AT NADIAD_2ND CALL.

Total Amount Rs:-

Sr. No. Description Qty Unit Rate Amount

Excavation for foundation upto 1.5M depth including dewatering & sorting out and stacking of useful materials and disposing of the excavated stuff upto 50 Meter Lead.

1.00 Loose or Soft Soil. 495.24 Cu.M. 117.08

Excavation for foundation 1.5M to 3.0M depth including dewatering & sorting out and stacking of useful materials and disposing of the excavated stuff upto 50 Meter Lead.

2.00 Loose or Soft Soil. 135.14 Cu.M. 129.81

Filling available excavated earth (exluding rock)in trenches plinth,sides of foundation etc.in layer not exceeding 20cm in depth consolidating each disposited layer by

ramming and watering.

Filling, Foundation & Plinth with murrum or selected soil in layers of 20 cms thickness including watering , ramming and consolidation etc complete. lead upto 10.00 km

Providing and laying cement concrete 1:3:6 ( 1: Cement : 3- Coarse Sand : 6- hand broken stone aggregates 40mm nominal size) and curing complete excluding cost of

5.00 formwork in 183.11 Cu.M. 3005.76

(A) Foundation & Plinth

Providing and laying controlled cement concrete M250 and curing complete including the cost of formwork but excluding reinforcement for reinforced concrete work in

6.00 Foundation, footing, Base of Columns and mass concrete 95.64 Cu.M. 4466.21

Providing and laying controlled cement concrete M250 and curing complete including the cost of formwork but excluding reinforcement for reinforced concrete work in

Column, upto two floor level.

Providing and laying controlled cement concrete M250 and curing complete including the cost of formwork but excluding reinforcement for reinforced concrete work in

8.00 Beams upto two floor level. 121.47 Cu.M. 6656.73

Providing and laying controlled cement concrete M250 and curing complete including the cost of formwork but excluding reinforcement for reinforced concrete work in

9.00 Shelves, Lintel, slab, landing upto two floor level. 150.14 Cu.M. 6225.44

Providing and laying controlled cement concrete M200 and curing complete including the cost of formwork but excluding reinforcement for reinforced concrete work in

10.00 Staircase upto floor two level 2.17 Cu.M. 6938.58

providing and mixing water proofing material in cement in mix proportion recommended by the manufacturers.

Brickwork using common burnt clay building bricks having crushing strength not less than 35kg/Sq.cm. In foundation and plinth in Cement mortar 1:6 ( 1-Cement :6- Fine

(B) Conventional

Brickwork using common burnt clay building bricks having crushing strength not less than 35kg/Sq.cm. In foundation and plinth in Cement mortar 1:6 ( 1-Cement :6- Fine

(B) Conventional

Extra for brickwork in super structure above floor two level

NADIAD MUNICIPAL CORPORATION

DISTRICT :- KHEDA

BID DOCUMENT FOR CONSTRUCTION OF URBAN HEALTH CENTER AT MANJIPURA AT NADIAD_2ND CALL

Sr. No. Description Qty Unit Rate Amount

Half brick masonary in common burnt clay building brick having crushing strength not less than 35 kg/sq.cm. In cement mortar 1:4 ( 1 cement : 4 coarse sand ) in

14.00 foundation and plinth (B) Conventional +Extra for brickwork in super structure above floor two level For Stair cabin. 251.21 Sq.mt. 640.33

15.00 Providing & Fixing S.S. Railing to flooring & wall including loading, unloading, taxes, labour etc complete as per Engineer In Charge. 9.90 Sq.mt. 2394.71

16.00 Providing TMT Bar FE 500D reinforcement for R.C.C. work including bending, binding and placing in position complete upto floor two level 63375.12 Kg 76.22

Providing 15mm thick cement plaster in single coat on Rough (Similar)side of single or half brick walls for interior plastering upto floor two level and finished even and

smooth in (i) Cement mortar 1:3 (1-cement:3-sand)

Providing 20mm thick sand faced cement plaster on walls upto height 10mt. Above ground level consisting of 12mm thick backing coat of C.M. 1:3 ( 1-cement : 3-sand ) and

18.00 8mm thick finishing cost of C.M.1 :1 ( 1-Cement : 1-Sand) etc. complete. 1131.70 Sq.M. 335.66

19.00 Providing throating or plaster drip and moulding ao R.C.C. Chhajja 84.24 R.M. 41.00

Providing and laying broken chine mosaic flooring for terrace using 12 mm to 20 mm broken pieces of glazed tiles to be laid over cement mortar 1:3 to plain or slope and to

20.00 be tempered to bring mortar creme out upto surface using white cement including rounding off junctions and extending them upto 15 cm along the wall,clearing with 442.95 Sq.M. 747.29

water and oxalic acid etc. as directed.

Providing and laying 24" x 24" Vitrified 8mm thick tiles flooring over 20mm (Average) base of Cement Mortar 1:6 (1-cement : 6-coarse sand) on new surface or fixing on

21.00 existing flooring by sdhesive materials including dismentalling of existing flooring and jointed with colour cement slurry including finished with flush pointing & cleaning the 771.59 Sq.M. 1397.83

surface etc. complete for Light Shade.

Providing and laying coloured glazed tiles of thesize 300 mm x 200 mm x 8 mm / 300 mm x 450mm x 8 mm in skirting, risers of steps and dedoon 10 mm. thick cement

plaster 1:3 (1 cement :3 coarse sand) & jointed with white cement slurry.

providing and laying Granite slab flooring or dedo over 20 mm base of cement mortar 1:6 (1 cement :6 coarse sand ) or L.M. 1:1.5 laid & jointed with gray cement slurry

including rubbing and polishing complete.

24.00 Labour Charges For Half Round edge for Granite 769.78 R.M. 85.85

25.00 Providing cement vata ( 10cm x 10cm size ) quarter round in cement mortar 1:1 including neat cement finishing watering etc. complete. 84.24 R.M. 23.69

Provoding and fixing flush door shutters, solid core construction with frame of first class hardwood with cross board and face veneer or plywood face panels, including

anodised alluminium butt hinges with necessary screws. (B) Non-decorative type and block board core anodised alluminium butt hinges in flush door shutters (2) 35 mm

Extra for using bright finished M.S. piano hinges of (A) Nickel plated piano hinges.

Providing and fixing FRP FRAME size 100 x 50 mm and 28 mm thick FRP degree panel shutters having extra reinforcement on sides and edges and in gel coat finish. The core

of the shutter is to be filled up with injected fire retardant grade polyurethane form done in situ along with embedded wooden pices for stiffening and also for taking

27.00 hingies and fixtures. The whole FRP frame and shutter is to be water proof, weather proof, terminte proof and resistance to mild acid/alkali, rates are to be inclusive of S.S> 18.90 Sq.M. 2377.77

hinges with necessary screws and alluminium fixtures and fastning product should have 3 years performance guarantee and company have ISO 9001-2000 certificte.

Providing and fixing M.S. grills of required pattern to wooden frame of windows with M. S. flat at required spacing & frame alround, square or round bars with round bars

28.00 with round headed bolts and nuts or by screws. 2728.80 Kg. 101.18

Painting two coats ( including priming coat ) on new steel and other metal surface with snthetic enamel paint ,brushing to give an even shade including cleaning surface of

all dirt, dust and other foreign matter.

NADIAD MUNICIPAL CORPORATION

DISTRICT :- KHEDA

BID DOCUMENT FOR CONSTRUCTION OF URBAN HEALTH CENTER AT MANJIPURA AT NADIAD_2ND CALL

Sr. No. Description Qty Unit Rate Amount

Applying two coats of putty & two coats of primer of approved brand and manufacture on new wall surface to give an even shade including thoroughly brushing the

surface free from mortar dropping and other foreign matter and sand papered smooth.

Wall Painting (Two coats) with plastic emulsion paint of approved brand & manufacture on under coated wall surface to give an even shade including throughly brushing

the surface free from mortar dropping and other foreign matter and sand papered smooth.

Finishing Wall with Weather Proof Exterior Emulsion Paint on wall Surface (Two Coats) to give an required shape even shade after throughly brushing the surface free from

mortar dropping and other foreign matter and sand papered smooth. Extra over Item 51 for every subsequent coat of water proofing cement paint of approved brand and

Providing and fixing extruded aluminum window, door or partition having extruded aluminum Colour anodized section frame main outer size 127mm x 38.10mm x 1.35mm

(of Jindal Section no:2443,@ Wt.1.384 Kg/mt), horizontal Four track member size 122.20mm x 31.75mm x 1.10mm (of Jindal Section no:8787,@ Wt. 1.205 Kg/mt),vertical

member of size 122.20mm x 31.75mm x 1.50mm (of Jindal Section no:8935,@ Wt. 1.398 Kg/mt) with sliding shutters of horizontal member size 40mm x 18mm x 1.29mm

(of Jindal Section no:8949 @ wt.of 0.456Kg/mt),vertical member of size 40mm x 18mm x 1.29mm (of Jindal Section no:8947 @ wt.of 0.456Kg/mt/Section 8948,@ Wt.

0.457 Kg/mt) with 5 mm thick transparent bronze colour tinted float glass with powder coated aluminum fittings and fixtures and transparent silicon sealant glass fixing to

frame as per details etc complete for window.

Providing laying and jointing in true line and level 25 mm dia. U.P.V.C. Pipe (SCH -40) line including fittings make or equivalent as apprroved by Engineer In charge. Pipe

34.00 shall be fixed on the wall with the help of clamp at every two meter C/C or shall be concealed as directed including necessary fittings etc. including testing of pipe and joints 210.00 R.M. 91.84

and fixing the same with adhesive solvent, including cost of all materials.

35.00 Providing erecting and fixing double coated ISI water tank of required capacity each with all necessary fittings and connection etc. complete on terrace 3000.00 Lit 3.95

Providing and fixing Ball Cock of Approved Quality as Directed

36.00 ( A ) Copper Metal 3.00 Nos 132.89

( I ) 25 mm dia.

Providing laying and jointing in true line and level 15 mm dia. U.P.V.C. Pipe (SCH -40) line including fittings make or equivalent as apprroved by Engineer In charge. Pipe

37.00 shall be fixed on the wall with the help of clamp at every two meter C/C or shall be concealed as directed including necessary fittings etc. including testing of pipe and joints 130.00 R.M. 72.65

and fixing the same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 35 mm dia. U.P.V.C. Pipe (SCH -40) line including fittings make or equivalent as apprroved by Engineer In charge. Pipe

38.00 shall be fixed on the wall with the help of clamp at every two meter C/C or shall be concealed as directed including necessary fittings etc. including testing of pipe and joints 100.00 R.M. 119.15

and fixing the same with adhesive solvent, including cost of all materials.

Providing and fixing Urinal of approved quality including connection with trap and with integral longitudinal flush pipe.(A) Squating plate pattern white earthenware

Providing and fixing washbasin with single hole for pillar tape with C.I. or M.S. brackets painted white including cutting holes and making good thesame but excluding

fittings. (A) vitreous china : II. Flat back washbasin 550 mm x 400 mm size (I) IN white colour

Providing and fixing screw down bib taps of following size.Brass screw down bib tap polished bright.

42.00 Providing and fixing Brass screw down stop tap/ Angle tap (A) 15 mm dia. 12.00 No. 205.83

43.00 Providing and fixing pillar tap,captan head, screw down high pressure with screws, shanks and back nuts. 15 mm Dia. 6.00 No. 308.73

Providing and fixing Brass screw down stop tap

( C) 25 mm dia.

Providing and fixing PVC SWR Nahni Trap IS 14735 for drain - 75 mm diameter with jali of the following nomonal diameter of self cleansing design with C.I. scread down or

hinged grating including the cost of cutting and making good the walls.

NADIAD MUNICIPAL CORPORATION

DISTRICT :- KHEDA

BID DOCUMENT FOR CONSTRUCTION OF URBAN HEALTH CENTER AT MANJIPURA AT NADIAD_2ND CALL

Sr. No. Description Qty Unit Rate Amount

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure poluthene pipes of the following outside Dia. Low densidy, complete with special falnge

compression type fittings, wall clipsetc. including making good the wall ceiling and floor. (F) 75mm

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure poluthene pipes of the following outside Dia. Low densidy, complete with special falnge

compression type fittings, wall clipsetc. including making good the wall ceiling and floor. (G)110 mm

Providing and fixing in position cowel vent to pipes.

Providing and fixing S.W. gully trap with C.I. grating brick masonry chamber and water tight C.I. cover with frame of 300mm x 300mm size (inside) with standard weight.(i)

Square mouth traps.(B) 150mm x 100mm size P or R type

Constructing Brick masonry road gully chamber 500mm x 450mm x 600mm including 500mm x 450mm C.I. horizontal grating wih frame

Providing and fixing Urinal or approved quality including conecting the Urinal with waste pipe, tap etc. complete.(A) White earthenware flat back or corner type size

Providing and fixing water closet Squtting pan (Indian type W.C. pan) size 580 mm (earthwork, bed concrete, foot rests and trap to be measured and paid for separately)

(A) Vitreous china (i) Long patter-white colour

Providing and fixing wsh down water closet (European type, W.C. Pan) with integral P or S trap including jointing the trap with soil pipe in Cement Mortar 1:1 (1-Cement : 1-

fine sand) (Seal and cover to be measured and paid for separately)(A) vitreous China Pattern :(i) in white colour

Providing and fixing ( 600 mm X 450 mm X 150 mm) size vitreous china laboratory sink brand of approved quality with CI or MS brackets painted white including cutting

holes and making good the same including providing and fixing 32 mm dia CP waste coupling rails providing fixing PVC waste pipe etc. comp as approved by the Engineer

in charge. The white glazed earthenware laboratory sink shall be 600 x 450 x 150 mm of best quality and make as approved by the Engineer-in-charge.

Providing and Fixing 6 mm thick Lexan Polycarbonate multi wall roofing sheet fixed with hilti screw and rubber silicon sealer and alluminium strip of size 50 x 3 mm etc.

complete as directed by Engineer in charge

56.00 Providing and fixing C.P. brass towel rail comlete with C.P. brass brackets fixed to wooden plugs with C.P. brass scews.(B) 600mm x 20mm size. 4.00 No. 603.20

Providing and laying polished Kota stone slab flooring over 20mm (Average) thick base of cement mortar 1:6 (1-cement : 6-coarse sand) or L.M. 1.1.5 (1-Lime putty :1.5 -

57.00 coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing etc. complete. (A) 25mm thick 12.07 Sq.M. 989.45

Providing and fixing 600mm x 450mm bevelled edge mirrror of superior glass mounted on 6mm thick A.C. sheet or plywood sheet and fixing to wooden pluge with C.P.

brass screws and washers.

Applying general insecticide pest control treatment to floors, cupboards etc including labour materials etc. complete. Using Imidacloprid 30.5 SCas Per IS 6313 part -II(

59.00 (0.075% concentration by mass) is recommended 10.5ml chemical diluted with 5 liters of water application 0.5 litre chemical /Sqm of surface is recommended as per I.S. 442.95 Sq.M. 89.29

Providing and fixing 3 mm thick 45x15 cm in size approved coloured Acrylic sheets as signage and display of health signs/information of required size having retro reflective

60.00 letters/design as per requirement, fixing the same through approved adhesive,G.I. Seam bolts and nuts 25mmx7mm etc . complete work shall e carried out as per 40.00 No. 227.25

instruction of Engineer-in-charge.

61.00 Providing and fixing brass cromium plated surgical handle cock of size of 15mm dia as per list etc. complete as directed by engineer incharge. 4.00 No. 1010.00

Providing & erecting water cooler having storage capacity 150 Ltr. & cooling capacity 150 Ltr.per hour @ an ambient temp of 450 C. The outlet temp. of the water should

drop by 150C within a hour, The water cooler should be comprising of hermetically sealed compressor, fan motor, condensing unit, water tank surrounded by evaporating,

coil, thermostats, relay etc.complete with necessary inlet & outlet connection. The body of water cooler will be made from Stainless Steel.

NADIAD MUNICIPAL CORPORATION

DISTRICT :- KHEDA

BID DOCUMENT FOR CONSTRUCTION OF URBAN HEALTH CENTER AT MANJIPURA AT NADIAD_2ND CALL

Sr. No. Description Qty Unit Rate Amount

Supplying & erecting 5 stage single reverse osmosis water purification system with M.S. powder coated frame, prefilter housing with 'O' ring presediment filter GAC filter,

carbon filter suitable buster DC pump capacity 80 psi, mention with 40 psi inline type post carbon filter auto low & high pressure switches with following size of storage

tank & LPH capacity & erected as directed with one year comprehensive maintenance guarantee.[B] 25 Ltr / Hr with 30 Ltr.

Supplying and erecting horizontal / vertical mounting type storage water heater with copper container housed in M.S./S.S. body insulated with glass wool / puff complete

64.00 with heating elements,adjustable thermostats 300 c to 850 C, indicating lamp, safety valve, fusible plug, etc.complete erected with coach bolts, nuts. washers & 1.00 No. 7027.58

cementation (A) 10 Ltr. with 3 KW. heating element Cat.III

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires up to

10 mtr length , in below type of pipe erected with 6A Modular type switch / bell push & accessories and earth continuity of following type, erected on PVC /

65.00 Metallic/Wooden box, single mounting base frame covered with textured/metallic/white front plate modules erected on / in wall / ceiling as per pipe erected, with 100.00 pts 449.45

necessary Lamp holder/ceiling rose / H.D.Connector as directed.

(a) with medium class Rigid PVC pipe and accessories erected flushed on wall/ceiling complete Cat. III

Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS PVC insulated multi strand copper wires up to 10 mtr

length, in below type of pipe erected with 6A Modular type switch and hum free EME step type electronic fan regulator mounted and accessories with earth continuity

66.00 of following type erected on PVC / Metallic/Wooden box, single mounting base frame covered with textured/metallic/white front plate modules erected on / in wall / 26.00 pts 638.32

ceiling as per pipe erected. with necessary ceiling rose / H.D.Connector as directed.

(a) with medium class Rigid PVC pipe and accessories erected flushed on wall/ceiling complete Cat. III

Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin socket erected on PVC / Metallic/Wooden box, single mounting base frame covered with

67.00 textured / metallic/white front plate modules erected on / in wall / ceiling with following type accessories 25.00 pts 257.55

Providing & erecting following type of Modular Type Accessories with necessary connection. As desired by Engineer In charge

68.00 (2) 16 Amp. SP one way switch 30.00 Ea 51.51

Providing & erecting following type of Modular Type Accessories with necessary connection. As desired by Engineer In charge

69.00 (3) 6/16Amp. Universal socket 30.00 Ea 82.82

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in

70.00 /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size (a) with medium class 500.00 mtr 82.82

Rigid PVC pipe and accessories (c) 3 wire 1.5 sq. mm

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected concealed in

71.00 /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size (a) with medium class 450.00 mtr 102.01

Rigid PVC pipe and accessories (d) 3 wire 2.5 sq. mm

providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of pipe to be erected in / on wall / ceiling

72.00 with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size (A) with medium class Rigid PVC pipe and 440.00 mtr 325.22

accessories (f) 3 wire 10 sq. mm (use earth wire of 4 sq.mm )

Providing & Erecting following Shockproof tissino type accessories erected on 3 mm thick PC (Polycarbonate) sheet in PVC/ Metal/Wooden Box. erected on wall/ ceiling.

(8) Bakelite lamp holder

74.00 Supplying KITKAT pattern porcelain cut-out fuse with base of following current capacity erected on existing block board. (v) 100 A. 500 V 6.00 Ea 278.76

NADIAD MUNICIPAL CORPORATION

DISTRICT :- KHEDA

BID DOCUMENT FOR CONSTRUCTION OF URBAN HEALTH CENTER AT MANJIPURA AT NADIAD_2ND CALL

Sr. No. Description Qty Unit Rate Amount

providing and erecting Miniature circuit breaker single pole 6A to 25A suitable to operate on 240 V A.C. system and having breaking capacity 10 KA to be erected in existing

box. confirming to IS 8828/1996 with ISI Mark cat III

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following

capacity (c)63 Amp cat III

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS

8623-1 & 3, IEC 61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) suitable for

(A) single phase incoming and horizontal single phase outgoing

(b) sheet steel double door (IP-43)

Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of

corrosion free hot dipped G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm having 200-250 Micron galvanising,

connection terminal dia of 12mm with constant ohmic value surrounded by highly conductive compound with high charge dissipation suitable for following type of

applications with chamber and heavy duty cover.(approved make OEM has to submit test certificate) & having back filling compound of (B) Inner chemical (CCM

Compound)- Resistivity:- 0.2 / meter testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no load & dry form, Sulphar content:- <2%(C) Back fill Compound :- Earthing

compound should be capable to retain moisture for long time Necessary test report must be submitted.

(b)For Electrical installation up to 11 KV in normal soil.

Length of Pipe : 2.00 mtrs

Back filling Compound :1 no. Bag of 25 Kg.

Providing & erecting Approved make Ceiling Fan with double ball bearing ISI mark with Condenser 230 volt A.C.50 Hz 1200 mm sweep complete having 3 blades aluminium

79.00 body and blade sets having ornamental design shanks , canopy erected with earthing. [ Make shall be approved by Engineer in Charge] 26.00 Ea 2311.89

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB, with housing used as a heat sink shall be made of thick

sheet Steel conforming to IS: 513/CRCA/ aluminium die cast powder coated and high U.V. & corrosion resistance with diffuser with company mark/name 160V to 270V,

Power Factor more than 0.9, THD < 15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

80.00 LED driver efficiency > 85 % 42.00 Ea 373.70

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown ranges of Wattage capacity of LED fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.)

(A) Tube Light with integral driver

(iii) 18-20 Watts, Surge - 2KV,IP-20, conventional 4 feet

NADIAD MUNICIPAL CORPORATION

DISTRICT :- KHEDA

BID DOCUMENT FOR CONSTRUCTION OF URBAN HEALTH CENTER AT MANJIPURA AT NADIAD_2ND CALL

Sr. No. Description Qty Unit Rate Amount

Supplying and erecting LED street light / Flood light fittings with High power White LEDs wattage of 3 Watt and above assembled on single MCPCB, efficiency more than

130 lm/w and corrosion free High pressure die cast aluminum housing with smooth finish powder coated and heat sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses, with toughened glass with company mark/name engraved or embossed 160 to 270 V,Power Factor more than 0.95, THD < 10 %, CCT 3000 K

to 5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED driver efficiency > 85 %.( fittings required LM-79 & LM-80 certificates)(NOTE: Below

81.00 description have shown ranges of Wattage capacity of LED fittings.The Engineer incharge may select any wattage capacity between the ranges shown.) 8.00 Ea 7266.95

(B) Flood Light (IP-65), Surge protection -4KV integral and ,Light must have 440VAC line supply with over-voltage protection.

(iv) above 90 to 120 watts

Box cutting the road surface to proper slope and camber for making a base for road work including ramming the excavated stuff and despositing on the road side slope as

directed up to 50 mt. lead.

Providing & laying spreading and compacting WBM Grade - II of B.T.M.C. metal 25mm to 90mm size (hand brocken) including using 20% (13+7%) filler i.e. stone screeing

13.2 mm at the rate 0.16 Cumt. & 0.08 stone dust including spreading in uniform thickness hand packing rolling with vibratory roller8-10 tonnes in stages to proper garde

and cmaber applying and brooming required types of screening/binding materials to fill up the interstices of coarse aggregate watering and compacting to the required

Providing and laying controlled cement concrete M.250 and curing complete excluding the cost of formwork and reinforcement for reinforced concrete work in (A)

Foundations, footings, Base of columns and Mass concrete.

Providing & Laying M.S. Side rail of road thickness with necessry nut boit plates, fixing as per width applaying plates vibrator, electric or diesel on channel comp. with V.D.

Systems (Trimix) by using the necessary equipments 7 material & Machinery, such as running screed vibrator on prelaid M.S. channel for leveling vaccum

pumps, floating & power trowling etc. compl. also including gruv cutting and filling joint with bituminous every 5 mtr. applying 4.50 kg / Sq.Mt. meatalic hardner.

Providing & Fixing Precast Rubber Dye/ Steel dye Interlocking Concrete Blocks 60 mm thick with grade of concrete M30 pnumetic compressed/ vibrated by mechanically

86.00 pressed and as per approved design confirming to IS 15658:2006 including 35 mm sand layer for leveling and filling the joint with sand in proper line and level as per 586.05 Sqmt. 686.91

guidelines of IRC: SP 63-2018 etc. complete.

Providing and fixing pre-cast concrete kerb stone of gray cement based concrete block 30cm length,30cm height and 15cm thick of M250 grade concret as per approved

design and including excavation for fixing in proper line and level,filling the joint with C:M 1:3 (1cement:3fine sand) etc complete.

Making trench in Hard Murrum / Tar Road of suitable width of 90 cms or required depth for laying any size of cable or locating the fault all over the run and back filling the

same and making the surface as normal ground.

Supplying and erecting approved make Octagonal pole made from HR sheet steel. The pole should be made as per IS. and shall be coated with hot dip galvanizing as per IS

2629/2633/4759, suitable suspend local wind speed with integral Junction box consist of terminal plate of min 6mm Hylam sheet, standard profile 35mmX7.5mm Din-Rail

for MCB Mounting, stud type terminal and arrangement for cable termination to be erected With Suitable foundation (Included) as per details given by manufacturer

considering site requirement.

(H) 9 Mtr. Long 70 mm Top X 155 mm bottom dia, 3 mm thickness with 260mmX260mmX16mm base plate, 4-M24 Bolts and 750mm long with necessary G.I. J Bolts

.Approx Pole weight 97 kg

Providing and erecting Street Light pole bracket comprising main B Class MS pipe of 4.2 cm/require outside dia. complete with suitable B Class M.S. sleeve tubing of approx.

45cms.length and suitable for 76.5 mm /80mm / required size of pole top having sufficient fasteners for fixing the brackets and having spread of 1.5.mtr. length with

90.00 deg.with vertical plane & suitable welded stays, reducer and with check nuts complete painted with one coat of Red oxide / PU base primer and two coats of Aluminium / 5.00 Each. 626.20

PU paint. paint with following nos of arms.

[A] Single Arm Bracket 1.5 Mtr

NADIAD MUNICIPAL CORPORATION

DISTRICT :- KHEDA

BID DOCUMENT FOR CONSTRUCTION OF URBAN HEALTH CENTER AT MANJIPURA AT NADIAD_2ND CALL

Sr. No. Description Qty Unit Rate Amount

Providing and erecting Street Light pole bracket comprising main B Class MS pipe of 4.2 cm/require outside dia. complete with suitable B Class M.S. sleeve tubing of approx.

45cms.length and suitable for 76.5 mm /80mm / required size of pole top having sufficient fasteners for fixing the brackets and having spread of 1.5.mtr. length with

91.00 deg.with vertical plane & suitable welded stays, reducer and with check nuts complete painted with one coat of Red oxide / PU base primer and two coats of Aluminium / 1.00 Each. 916.07

PU paint. paint with following nos of arms.

[B] Double Arm Bracket 1.5 Mtr

Supplying and erecting LED street light / Flood light fittings with High power White LEDs wattage of 3 Watt and above assembled on single MCPCB, efficiency more than

130 lm/w and corrosion free High pressure die cast aluminum housing with smooth finish powder coated and heat sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses, with toughened glass with company mark/name engraved or embossed 160 to 270 V,Power Factor more than 0.95, THD < 10 %, CCT 3000 K

to 5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED driver efficiency > 85 %.( fittings required LM-79 & LM-80 certificates)(NOTE: Below

92.00 description have shown ranges of Wattage capacity of LED fittings.The Engineer incharge may select any wattage capacity between the ranges shown.) 7.00 Each. 5976.17

(A) Street Light (IP-65), Surge protection -4KV integral and ,Light must have 440VAC line supply with over-voltage protection.

Supplying and erecting Flexible PVC insulated multi strand multi core 1.1 kv grade ISI marked copper wires of following size to be erected as directed.

(e) 1.50 Sq.mm 3 core round PVC sheathed

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench /

94.00 pipe of following size of cables 168.00 R.Mt. 140.39

(C) 4 core 10 Sq. mm

Providing and erecting Pipe type earthing having 150 cms.long and 2.5 cms. dia. galvanised iron pipe with coupling and buch buried in specially prepared earth pit complete

with necessary 8 SWG earth wire.

96.00 For using salt and charcoal / coke as required for pipe type earthing. 6.00 Each. 171.70

97.00 Providing and erecting HOT deep Galvanised iron strip wire 8 to 16 SWG. 15.00 Kgs. 77.77

Supplying & erecting IP 55 grade following size section pillar fabricated from joint less M.S. Sheet with angle iron legs made from jointless M.S. Angle with cable clamps to

be buried in ground to have appropriate erection to work uniform until erected with cement concrete foundation and 45 cm high bricks work finishing with plaster etc.

hinged double door internally supported on both side, with internal and outside looking arrangement with look and keys in duplicate 35 x 35 x 5 mm M.S. Angle of Two

98.00 Nos. one is welded and other with nut and bolt for erecting Bakelite sheet. Painting the Section Pillar inside and out side with three tank powder coated paint. section 1.00 Each. 16691.26

pillar roof should be without joint with water leakage proof & tested as per IP 55 test & followed by IS 2147 of

(A) 150 X 90 X 75 cm section pillar fabricated from 14 Gauge MS Sheet with angle iron legs 95 cm long made from 40 X 40 X 6 mm thick MS angle.

Supplying and erecting HYLAM sheet on existing angle iron frame.for following thickness

Providing and erecting Approved make Four pole moulded case circuit breaker having breaking capacity ICU of 35 KA. at 415 V. having normal current rating 125A. with

Fixed thermal & magnetic release suitable to work on A.C.supply 50 c/s. with all internal connections, spreader tinned copper & complete erected in existing 16 G.M.S.

ICS=100% of ICU only Cat III

Supplying and erecting approved make Segment time switch suitable for 230V+10%16A. floating contacts with 24 hour dial having15/30 min. segments with early manual

101.00 override switching for on & off without influencing the program sequence with quartz time switch With power reserve, housed in fire proof thermoplastic enclosure & 1.00 Each. 2226.04

transparent cover terminal covers erected as required wire necessary connection erected as directed.

NADIAD MUNICIPAL CORPORATION

DISTRICT :- KHEDA

BID DOCUMENT FOR CONSTRUCTION OF URBAN HEALTH CENTER AT MANJIPURA AT NADIAD_2ND CALL

Sr. No. Description Qty Unit Rate Amount

Providing & erecting 415V MCB Four Pole Switch for Lighting Load (B curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity

(B) 40 Amp. Cat.III

Providing 1:2:4 cement concrete foundation & 70 % PCC from bottom including excavation for the pole of size 60 x 60 x 150 cm. Deep in below ground level with plinth of

103.00 45 cm x 45 cm(or 45 cm dia x 45 cm) high upper ground level with necessary curing and finishing in approved manner. 6.00 Each. 1652.36

( for 9 & 10 mtr pole)

Providing & laying approved make Double walled corrugated pipes (DWC) of polyethylene(conforming to IS 14930 II )with necessary connecting accessories of same

104.00 material at required depth in existing trench for laying of cable. below ground / road surface for enclosing cable 168.00 Rmt. 73.73

(B)63mm outer dia

providing and erecting Miniature circuit breaker single pole 6A to 25A suitable to operate on 240 V A.C. system and having breaking capacity 10 KA to be erected in existing

box. confirming to IS 8828/1996 with ISI Mark Cat.III

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals

106.00 with brass/cadmium plated nut bolts in an approved manner. 24.00 Each. 13.13

Total Amount Rs:-

Total Amount Rs:-

Consultanting Civil Engineer City Engineer

Dharmesh Deshani OPC Pvt Ltd Nadiad Municipal Corporation

Ahmedabad Nadiad