SPECIAL REPAIRS TO BLDG NO WL-43/1 and 43/2 (2xJCOs MD ACCN) OF MH and DSC RECORDS AT KANNUR MIL STN UNDER AGE (I) KANNUR

Amount

Dismantling of Mangalore Pattern roofing tiles or similar tiles in roofing complete all as specified and as directed.

Dismantling of battens for tiles, shingles etc., of any size including tilting fillets spaced exceeding 15 cm complete all as specified and as directed.

Dismantling of timber scantlings 40 sqcm and over in section in any position, unframed work complete all as specified and as directed.

Dismantling wall and ceiling boards (fiber, pulp, insulation etc) or insulation boards, slabs, blankets, any thickness, including cover fillets all as specified and as directed

M&L for second class Hard Wood scantlings, clean sawn as in rafters, purlins etc; framed and fixed as directed by Engineer-in-charge without finish complete all as specified and as directed.

All as in item No. 5 above but for except timber complete all as specified and as directed.

M&L for steel work rectangular/ tubular trusses as in purlins etc including special shaped washers etc complete using ERW or induction butt welded tubes conforming to IS specifications complete all as specified and as directed.

S&F 0.50 mm total coated thickness prepainted galvalume aluminium zinc coating GI based corrugated steel roofing sheets having tensile strength of 550 MPa colour coated with self tapping screws as per manufacturers instruction complete all as specified and as directed.

S&F 0.50 mm thick pre-painted galvalume aluminium zinc coating GI based plain steel of any colour, having tensile strength of 550 MPa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F PVC (SWR) pipe 200 mm bore as in half round valley gutters including suitable drop ends/stop end and fixing with MS/PVC clamps suitable for steel sheet roofing complete all as specified and as directed

S&F PVC (SWR) down take pipe 75mm bore single socketed, in any length with rubber ring joints, fixed to wall complete all as specified and as directed.

M&L for preparing surfaces of wood and wood based materials new or old, of any description and girth, not otherwise described and treated with two coats of creoste oil complete all as specified and as directed.

All as in item no 12 above but one coat over of creoste oil.

M&L for preparing new or previously un treated steel surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer complete all as specified and as directed.

M&L for GI framework for seamless false ceiling (size of grid 605mm x 605mm) comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 mm and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exceeding 1.2 m length ) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre, suspended with hangers 6 mm dia (up to 1200 mm length) GI wire of suitable length adjusting level fixed to roof by means of ceiling cleats made out of GI Flat 40x3mm size 60mm long complete all as specified and directed

S&F 4 mm thick non asbestos fiber cement building boards fixed to GI frame work as per manufacturers instructions as in ceilings flat or sloping complete all as specified and directed.

M&L for preparation of new unplastered / unplastered surface on ceiling and applying three coats of white wash complete all as specified and as directed.

Demolition of concrete in ground floor and pavings not exceeding 15 cm thickness (below or above GL) for cement concrete un-reinforced complete all as specified and as directed.

Roughening surfaces of old concrete floor by picking, seeping clean and washing down with water to remove dust etc complete all as specified and as directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete all as specified.

Demolition of brick work or concrete/ stone masonry wall built in cement mortar, including all quoins, arches, pillars etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Demolition of cement concrete (reinforced) not exceeding 15cm thickness in floors (other than ground floors) and similar suspended work complete all as specified and as directed.

Taking down plastering in cement or cement lime plaster any thickness complete all as specified and as directed.

M&L for 25mm thick cement concrete 1:2:4 type B0 using 12.5mm graded stone aggregate as in flooring complete all as specified and as directed.

M&L for 50 mm thick cement concrete 1:4:8 type D-2, using 40mm graded stone aggregate as in sub base complete all as specified and as directed.

M&L for 25 mm thick cement concrete 1:2:4, type B-1, using 20mm graded stone aggregate as in floor complete all as specified and as directed.

M&L for coloured joint free non skid ceramic tiles 10 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for coloured non skid ceramic tiles, 7 to 8 mm thick, area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for coloured glazed ceramic tiles 300x200x7mm on vertical surfaces of wall such as skirting dado etc. set and jointed in net cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for 20 mm thick, granite work (table rubbed and polished) as in cooking platform set and jointed in net cement slurry pointed with white cement 1:2 using marble dust with admixture of pigment to match with shade of granite, complete all as specified and as directed.

M&L for 20mm thick granite work (table rubbed and polished) as in wall lining set and jointed in net cement slurry pointed with white cement 1:2 using marble dust with admixture of pigment to match with shade of granite, complete all as specified and as directed.

M&L for screed bed or bedding layer in cement mortar 1:6, 20mm thick for laying floor finishes complete all as specified and as directed.

M&L for 10mm thick cement mortar on stone surface as backing coat in CM 1:4 finished rough to receive tiles complete all as specified and as directed.

M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed.

M&L for reinforced cement concrete 1:2:4 type B1, using 20mm graded stone aggregate as in slabs as complete all as specified and as directed.

M&L for walling of laterite stone walls uncoursed, well bonded bedded and solidly hearted built in cement mortar 1:6 complete all as specified and as directed.

All as per item No.36 above, but except stone (old serviceable stone reused in the work)

M&L for providing precast cement concrete solid building blocks of 1:2:4 Type B1, using 20 mm graded stone aggregate or slabs 10 cm thick (with plain or interlocking joints as directed) setting in Cement Mortar 1:6 complete, in walls complete all as specified and as directed.

M&L for rendering 10mm thick in CM 1:6 on stone masonry surface finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15 mm thick in CM 1:4, on stone masonry surface finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 10 mm thick in CM 1:4 on concrete surface finished even & smooth without using extra cement complete all as specified and as directed.

Taking down chowkats or frames and not exceeding1.5 Sqm each with shutters (without taking of shutters from the frame) complete all as specified and as directed.

Taking down chowkats or frames and but exceeding 1.5 Sqm and not exceeding 4 Sqm with shutters (without taking off shutters from the frame) complete all as specified and as directed.

Taking down wooden shutters of any description not exceeding 1 Sqm each complete all as specified and as directed.

Taking down wooden shutters of any description exceeding. 1 Sqm and not exceeding 2 Sqm each complete all as specified and as directed.

Taking down shutters of any description, not exceeding 1 sqm each and refixing in same openings complete all as specified and as directed.

Taking down shutters of any description, exceeding 1 sqm and not exceeding 2 sqm each and refixing in same openings complete all as specified and as directed.

Cutting holes in stone walls built in CM, exceeding one brick but not exceeding two bricks for inserting hold fast and making good dismantled portion in CM 1:3, or cement concrete 1:2:4 type B1 complete all as specified and as directed.

S&F flat iron hold fast and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed.

M&L for cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in in hold fast blocks including necessary form work etc complete all as specified and as directed.

M&L for IInd class hard wood, plain solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed.

M&L for IInd class hard wood plain, framed panelled door shutters 35 mm thick (any number of panels) with panels of timber flat on both sides or of veneered particle board medium density wood particle board with commercial face veneers and fitted to chowkats etc complete all as specified and as directed.

M&L for glazed and skeleton shutters, 30 mm thick open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); and fitted to chowkats complete all as specified and as directed.

All as per item no.53 above, but 35mm thick for door shutters

M&L framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con-forming to Fe.290.Gde-E-165 complete all as specified and as directed.

M&L for 18/19 mm thick block boards, grade 1 quality, exterior grade, decorative type with decorative face veneer on one faces complete all as specified and as directed by Engr-in-charge.

M&L for teak wood lipping, 6 mm thick, fixed with nails for 18/19 mm thick block board complete all as specified and as directed.

S&F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised with width of flaps (When open) 40 mm complete all as specified and as directed.

S&F Ball catches with 8mm dia steel ball, brass body and striking plate including letting in complete all as specified and as directed.

Hacking out old broken window/ventilator glass (any thickness, size, quality or description) for wooden metal frames or stone concrete surrounds glazed with putty or fixed with beads complete all as specified and as directed.

S&F sheet glass, 3 mm thick, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S&F figured glass, 3mm thick, pin head type and glazing with oil putty in squares not exceeding 0.5sqm in each pane complete all as specified and as directed.

S&F stainless wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.4 mm and fixed with stainless steel wire staples complete all as specified and as directed.

S&F in repairs 150 mm size aluminium anodized barrel tower bolts of extruded section complete all as specified and as directed.

Fixing only in repairs 150 mm size aluminium anodized barrel tower bolts of extruded section complete all as specified and as directed.

S&F in repairs 100 mm size aluminium anodized barrel tower bolts of extruded section complete all as specified and as directed.

Fixing only in repairs 100 mm size aluminium anodized barrel tower bolts of extruded section complete all as specified and as directed.

S&F 300mm size aluminium alloy, anodized, sliding door blot with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section or cast aluminium alloy complete all as specified and as directed.

S&F in repairs 100mm size stainless steel butt hinges medium weight complete all as specified and as directed.

Fixing only in repairs 100mm size stainless steel butt hinges medium weight complete all as specified and as directed.

S&F in repairs 75mm size stainless steel butt hinges medium weight complete all as specified and as directed.

Fixing only in repairs 75mm size stainless steel butt hinges medium weight complete all as specified and as directed.

S&F 150mm size extruded aluminium alloy anodized handle fabricated type complete all as specified and as directed.

Fixing only 150mm size extruded aluminium alloy anodized handle fabricated type complete all as specified and as directed.

S&F 100mm size extruded aluminum alloy, anodized handle fabricated type complete all as specified and as directed.

Fixing only 100 mm size extruded aluminium alloy anodized handle fabricated type complete all as specified and as directed.

M&L for preparing new wooden surfaces over 10 cm width or girth and applying two coats of synthetic enamel painting over a coat of primer complete all as specified and as directed.

M&L for preparing old wooden surfaces over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for preparing back of chowkats of area not exceeding 0.50 Sqm each and treated with tar or coal tar black paint complete all as specified and as directed.

M&L for preparing and treating small articles such as hold fasts etc of area not exceeding 0.1 Sqm each complete all as specified and as directed.

M&L for preparing old treated steel/iron surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

S&F solid PVC door frame of sizes 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, as per specification and drawings complete all as specified and as directed.

S&F factory made solid PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain coloured PVC “C” channel having a PVC sheet strip of 20mm width stock inside with solvent cement for stiles and plain colour PVC sheet for top rails, lock rails and bottom rails on either side and as gap insert for top rail & bottom rail on either side and as gap insert for top rail and bottom rail, paneling of plain colour of PVC sheet fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement etc. Details as peer specification and drawings complete all as specified and as directed.

S&F Harrison rails, anodised aluminium alloy with fixing brackets of 15 cm long, stops, rollers etc. all as specified and as directed.

Excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m deep for foundation and getting out in hard/dense soil complete all as specified.

M&L for PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and as directed.

M&L for reinforced cement concrete 1:1.5:3, type A1, using 20mm graded stone aggregate as in foundations, including footings, plinth beams, bases for columns etc complete all as specified and as directed.

M&L for reinforced cement concrete 1:1.5:3, type A1, using 20mm graded stone aggregate as in columns complete all as specified and as directed.

M&L for reinforced cement concrete 1:1.5:3, type A1, using 20mm graded stone aggregate, as in beams complete all as specified and as directed.

M&L for reinforced cement concrete 1:1.5:3, type A1, using 20mm graded stone aggregate as in slabs complete all as specified and as directed.

M&L mild steel TMT bars 10mm dia and over cut to length bent to shape required including cranking ,bending, spirally for hoping for columns hooking ends and binding with MS wire annealed not less than 0.90 mm dia complete all as specified and as directed.

All as in item 91 above, but 6 to 8mm dia bars in stirrups, spacers and binders complete all as specified and as directed.

M&L for form work to sides of concrete foundations, footings, bases of columns and plinth beams and similar work finished rough in flat complete all as specified and as directed.

M&L for form work to sides of columns and similar work finished rough in flat complete all as specified and as directed.

M&L for form work to sides and soffits of floor or roof beams etc including supports, overhangs etc finished rough in flat complete all as specified.

M&L for form works to soffits of slab rough finished surfaces of concrete complete all as specified and as directed

M&L for form work to edges of concrete flats, floor and roofs not exceeding 20 cm wide and similar work exceeding 5cm but not exceeding 10cm wide finished rough complete all as specified.

Returning filing in including spreading, levelling ,watering and well ramming in layers not exceeding 25 cm in hard/ dense soils complete all as specified and as directed.

Removing excavated material to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed.

Dismantling water tanks of capacity exceeding 250 but not exceeding 500 litres and removing to store complete all as specified and as directed.

S&F rotational moulded polyethylene water storage tanks (cylindrical, vertical with closed top) of capacity 500 litres, hoisted and fixed in position all as specified in SSR Part I complete all as specified and as directed.

S&F Ball brass valves, 25mm bore high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed.

Taking down GI tubing and connection and removing to store of pipe up to 25mm bore complete all as specified and as directed.

Dismantling of cast iron drain pipe75/ 100mm dia complete all as specified and as directed.

Taking down LDPE pipes of any description size 32mm bore complete all as specified and as directed.

S&F 110mm PVC (SWR) pipe single socketed in any length with rubber ring joints, fixed to walls complete all as specified and as directed.

All as in item no.106 above but laid in trenches or on floors

S&F 75mm PVC (SWR) pipes, single socketed in any length with rubber ring joints, fixed to walls complete all as specified and as directed.

S&F 75mm PVC (SWR) pipes, single socketed in any length with rubber ring joints, laid on floors complete all as specified and as directed.

S&F 110mm PVC (SWR) vent cowl complete all as specified and as directed.

S&F 75mm PVC (SWR) bends any radius complete all as specified and as directed.

S&F 75mm PVC (SWR) bends any radius with access door complete all as specified and as directed.

S&F 110mm PVC (SWR) bends any radius complete all as specified and as directed.

S&F 110mm PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and as directed.

S&F in repairs125/110mm size PVC (SWR) Gully trap including setting and jointing with solvent cement complete all as specified and as directed.

S&F in repair 75mm size PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and as directed.

S&F grating, square, 150mm size of PTMT complete all as specified and as directed.

M&L for 15mm bore unplasticized PVC pipe of pressure rating 10Kg f/cm² fixed on walls, ceilings or on floor complete all as specified and as directed.

Ditto all as per item no. 118 above, but 20mm bore

Ditto all as per item no. 118 above, but 25mm bore

Cutting chases not exceeding 10cm girth in stone work, concrete block or slab walls for concealed water tubing and making good complete all as specified and as directed.

S&F in repairs water closet vitreous china squatting pan, Orissa pattern of size 580 x 440 mm, white with integral foot rest, including laid in lime concrete bedding complete all as specified and as directed.

S&F in repair low level PVC flushing cistern, 10 litres capacity, white with inlet ball valve float and handle including brackets complete all as specified and as directed.

S&F in repair flush pipe of polyethylene low or high density PVC 32mm bore for low level cistern complete all as specified and as directed.

S&F Vitreous China wash basin, white, flat back, of size 630x450mm excluding taps, waste chain & plug & porcelain stopper but including brackets complete all as specified and as directed.

S&F kitchen sinks made of stainless steel, 1 mm thick, overall size 495mm x 420mm and bowl size 410mm x 330mm x 160mm, with plugs, washers and wastes, etc., including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, complete all as specified as directed.

S&F in repairs 15mm pillar taps, fancy type, cast copper alloy with capstan heads, chromium plated screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe complete all as specified and as directed.

M&L for 32mm dia waste fittings brass chromium plated for sinks, WHB etc with long screwed shanks and fly nuts flange end bedded in red lead cement and other end complete all as specified and as directed.

S&F PVC connections 15mm size with PTMT nuts on both sides, of length 600mm, complete all as specified and as directed.

S&F in repairs chromium plated fancy type bib tap cast copper alloy with crutch or butterfly handle screwed and down screwed for iron pipe or for brass ferrule of 15mm bore complete all as specified and as directed.

S&F stop cocks, cast copper alloy, chromium plated with long shank and cup (concealed type), high pressure with capstan head handle, screwed both ends for iron pipe or for unions of 15 mm dia complete all as specified and as directed.

S&F angle cocks, cast copper alloy, chromium plated with long shank and cup , high pressure with capstan head handle, screwed both ends for iron pipe or for unions of 15 mm bore complete all as specified and as directed.

S&F in repairs 20mm bore stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and as directed.

S&F in repairs 25mm bore stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and as directed.

S&F 32mm bore low density polyethylene pipe (LDPE) of pressure rating 6kgf/cm2 fixed to walls, floors or in ceilings etc complete all as specified and as directed.

S&F 50mm bore low density polyethylene pipe (LDPE) of pressure rating 6kgf/cm2 fixed to walls, floors or in ceilings etc complete all as specified and as directed.

S&F in repairs shower rose, chromium plated, 125mm complete all as specified and as directed.

M&L for shower arm, 15 mm size, 195 mm long with bend of 45 degree with flange, of PTMT any colour complete all as specified and as directed.

S&F tubular towel rail, brass chromium plated, 20mm dia, D type, 600mm long between flanges complete all as specified and as directed.

M&L for Cutting into existing manholes for connecting new drains of 100mm dia pipe , making good to pipe & rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required, complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C-2, using 40mm graded stone aggregate finished even and fair as in plinth protection complete all as specified and as directed.

M&L for cement concrete1:3:6 type C1 using 20mm graded stone aggregate as in surface channels and drains complete all as specified and as directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms moulds, mitred/stopped ends etc complete all as specified and as directed.

M&L for rough excavation not exceeding 1.5 m deep and getting out in hard/dense soil complete all as specified and complete all as specified and as directed.

M&L for hardcore of broken stone aggregate or boulders of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L for 100mm thick cement concrete 1:4:8 type D-2,using 40mm graded stone aggregate finished even and rough to receive the topping layer as in sub bases complete all as specified and as directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

M&L for machine pressed precast concrete interlocking paver block with grey cement and pigment, any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade, complete all as specified and as directed

M&L for complete removal of existing treatment on surfaces of wall by scrapping down old treatment, preparing surface even and smooth using wall care putty and applying two coats of oil emulsion distemper over a coat of primer complete all as specified and as directed

M&L for preparation of new plastered surfaces of walls, preparing surface even and smooth using wall care putty and applying two coats of oil emulsion distemper over a coat of primer complete all as specified and as directed.

M&L for complete removal of existing treatment on external walls by scrapping down old treatment and applying two coats of exterior grade anti-algae acrylic emulsion paint over one coat of wall primer paint including preparation of surfaces using wall care putty etc complete all as directed as per manufacturers instructions. (Make : Asian Paints Apex Ultima or techno commercially equivalent )

M&L for preparing newly plastered surfaces of external walls and applying two coats of exterior grade anti-algae acrylic emulsion paint over one coat of wall primer paint over wall care putty complete all as directed as per manufacturers instructions. Make: Asian Paints Apex Ultima or techno commercially equivalent)

S&F in repairs Aluminium Hat pegs, solid body, 125 mm to 175 mm complete all as specified and as directed.

S&F in repairs, Soap dish, vitreous China white, approximate size 160x 160x 90mm, fixed to plugs with chromium plated brass screws complete all as specified and as directed.

S&F Towel Ring of PTMT (min. weight 90 gms) including CP brass screws and wooden/plastic cleats etc complete all as specified and as directed.

S&F in repairs stainless steel kitchen plate racks of 1 mm thick of overall size 900 mm x 900 mm as per trade pattern complete all as specified and directed by Engineer-in-Charge

Taking down carefully copper/aluminium point wiring of light, fan, socket or power complete, including fitting such as switches, ceiling roses, pendants, regulators, sockets etc. and making good disturbed surfaces of walls, floor ceiling etc. complete all as specified and as directed.

M&L for point wiring complete with 1.5 Sqmm single core, PVC insulated unsheathed copper conductor FRLS cable, multi-stranded 1100 V grade drawn through and including non-metallic rigid PVC conduct, concealed in wall complete, fixed in roof, etc with necessary fixing accessories such as bend, elbow, socket, saddles etc with and including 1.5 sqmm, single core PVC insulated unsheathed copper conductor FRLS cables multi stranded, 1100 volt grade, green in colour as earth continuity conductor connected to common earth dolly complete all as specified and directed for:- Note: Cutting chases for fixing conduit shall be measured and paid separately.

(i) One light point controlled by one switch complete all as specified and as directed.

(ii) One ceiling fan/exhaust point controlled by one switch complete all as specified and as directed.

(iii) One 3 pin, 5 Amps switch socket on independent board complete all as specified and as directed.

(iv) One 3 pin, 5 Amps switch socket on same board with other switches complete all as specified and as directed.

All as per srl item No 159 above, but for one 3 pin, 15 Amps, switch socket combination on independent board with FRLS cable of size 4 Sqmm with and including 4 sqmm copper conductor cable as earth continuity conductor green in colour and connected to common earth dolly all as specified and directed.

Cutting chases on wall of width 30mm, depth 35mm for concealing PVC conduct of 20/25mm dia, with and including replastering, smooth finishing to match the existing colour of the wall complete all as specified and as directed.

Cutting chases on wall of width 50 mm, depth 35mm for concealing PVC conduit of 20/25 mm dia, with and including replastering, smooth finishing to match the existing colour of the wall complete all as specified and as directed.

Cutting chases on wall of width 75mm, depth 35 mm for concealing PVC conduct of 20/25mm dia, with and including replastering, smooth finishing to match the existing colour of the wall complete all as specified and as directed.

S&F modular switch, 240 V, one way, single pole, 6 Amps one module including connecting up electrically complete all as specified and as directed.

S&F modular switch, 240 V, one way, single pole, 16 Amps one module including connecting up electrically complete all as specified and as directed.

S&F switch, bell push modular type, 240 V, 6 Amps one module including connecting up electrically complete all as specified and as directed.

S&F ceiling rose of polycarbonate, 3 terminal including connecting up electrically all as specified and directed.

S&F socket, outlet, 2/3 pin 6 Amps, multipurpose, modular type, including connecting up electrically complete all as specified and directed.

S&F socket, outlet, modular type 2 in 1 2/3 pin 6 & 16 Amps, including connecting up complete all as specified and as directed.

S&F Calling bell AC 240V single pole including connecting up electrically complete all as specified and as directed.

S&F modular white cover plate with frame for two module complete all as specified and as directed.

S&F modular white cover plate with frame for three module complete all as specified and as directed.

S&F modular white cover plate with frame for four module complete all as specified and as directed.

S&F modular white cover plate with frame for six module complete all as specified and as directed.

S&F modular white cover plate with frame for eight module complete all as specified and as directed.

S&F modular metal flush box for one/two module complete all as specified and as directed.

S&F modular metal flush box for three module complete all as specified and as directed.

S&F modular metal flush box for four module complete all as specified and as directed.

S&F modular metal flush box for six module complete all as specified and as directed.

S&F modular metal flush box for eight module complete all as specified and as directed.

S&F sheet metal enclosure factory made for MCB DB, SP 8 way with 200 Amps bus bar 415 Volt, double door type, fixed/flushed on wall including electrically connecting up complete all as specified and directed.

S&F in replacement sheet metal enclosures distribution boards, double door 4 way three phase 415 volts MCCB, ISOLATOR & MCB's comprising three phase four wire copper strip bus bar of appropriate capacity complete all as specified and directed and comprising of the following:- (a) MCCB 4 Pole 100 AMPS AC 415 V 10 KA = 01 NO as incoming (b) MCB SP 40 AMP = 12 Nos as out going Note:- (i) The DB shall be VTPN series of Make:- Hagger CAT PART No VYV04DMZ or techno commercially equivalent. (ii) The DB shall be flush fixed and making good the disturbed surface matching with existing specifications shall be part of job at no extra cost. (iii) Connection of the MCCBs/ MCBs with cable shall be made through appropriate size pin/ bottle type thimble-properly crimped. (iv) All the vacant holes of the DB shall be provided with blank plates of appropriate size. (v) Double continuous earth wire shall be provided for each three phase DB from earthing mains dolly.

S&F MCB SP, 240 Volt, 6 to 32 Amps including electrically connecting up using wiring lugs complete all as specified and as directed.

S&F MCB SPN, 240 Volt, 40 Amps including electrically connecting up using wiring lugs complete all as specified and as directed.

Taking down unserviceable tube light fitting and S&F decorative ultra slim linear LED light fittings with extruded Aluminium, heat sink, environmental friendly, energy efficient ready to use pack of 20W LED 6500K and electrically connecting up complete all as specified and as directed. Make:- Model LDLL20-WW of Crompton or of SSK-T-5 22W of Syska or techno commercially equivalent

Taking down old unserviceable tube light fitting and S&F decorative ultra slim linear LED light fittings with extruded Aluminium, heat sink, environmental friendly, energy efficient ready to use pack of 10W LED 6500K and electrically connecting up complete all as specified and as directed. Make:- Model LDLL10-WW of Crompton or of SSK-T-5 12W of Syska or techno commercially equivalent.

Taking down old unserviceable bulk head fitting from wall and S&F 10watt LED Bulk head fitting environmental friendly ultra modern, energy saving, surface mounted decorative hexagon bulk head Back lit LED luminaire comprising of high brightness LEDs complete all as directed. Make: Havells Cat Part HEXAFT10WLED857SSYMBOPC or techno commercially equivalent

S&F in replacement Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

M&L for earthing complete with galvanized steel earth plate electrode 60cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.5m below normal ground level connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron connected to earthing test point, main DB, panel board, continuous earth lead protected by 15mm bore GI pipe light grade, 20mm bore GI light grade pipe for watering, necessary excavation and earth work in any type of soil, PCC pit, RCC chamber cover with suitable reinforcement complete all as shown on electrical plate No 3 of SSR part-I of 2009 all as specified and directed. Note:- Rate quoted shall deem to include for GI earth and GI pipe lead up to 7.5m length complete all as specified and as directed.

Supply and fixing in replacement LED Ball type Lamp 10 watt complete all as specified and as directed.

M&L for sub main wiring with two runs of single core 4 Sq mm copper conductor FRLS cable, PVC insulated, unsheathed multistanded, 1100V grade drawn through and including non metallic rigid PVC all accessories such as bend, elbow, socket, tee saddles etc., fixed concealed to wall / fixed to ceiling etc including 2.5 Sq mm single core copper conductor FRLS cable PVC insulated, unsheathed multistranded 1100 V grade as earth continuity conductor connected to common earth dolly complete all as specified and directed. Note:- 2 runs of 4 Sq mm, one run of 2.5 Sq mm copper cable and one run of PVC conduit will be measured as one length.

S&F electronic stepped modular type regulator two module, 120W suitable for ceiling fan 230V complete all as specified and as directed.

Taking down carefully ceiling fan with rod from ceiling / roof/ wall and depositing in MES store and S&F ceiling fan 1200mm sweep, 230 volt, single phase, 50 Hz, BEE star rated complete all as specified and as directed. Make : Havells Cat Part No ES 50 or Techno commercially equal.

S&F exhaust fan single phase, 230 volts, 1400 RPM, non metallic, 200 mm dia sweep, including louvers, fixing accessories, making hole and additional alternation, making good as per site requirement for suitable size etc., complete all as specified and directed .

SANTOSH CONSTRUCTIONS

T.P.SUNIL KUMAR