CWEK-35/2019-20

Amount

SCHEDULE A PART I (B/R WORKS)

Dismantling plain or corrugated mild steel sheeting any gauge, thickness, including Nanital or similar pattern roof covering, complete all as specified.

Supply and fixing for 0.63mm Galvanised, Corrugated Mild steel sheeting with two corrugations side lap, fixed with L-type or J-type or cranked hook bolts and washers, ISI marked,, in roofs, walls etc. with grade of zink coating 275, complete all as specified.

Fixing only galvanised, corrugated mild steel, sheeting with two corrugation side lap fixed with L type or J type or cranked hook bolt and bent to curve (of any radius) as in roof covering complete all as specified and as directed Note :-Sheets obtained from dismantling from item No.1.01 shall be reused.

Supply and fixing 0.80 mm thick Plain, galvanized mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) of class-2, ISI Marked, complete all as specified.

Demolition of Stone slabs and tiles of any description or thickness in floors , aprons etc. (Demolition Laid, bedded and pointed in any mortar) complete all as specified and as directed.

Material and Labour for stone sett flooring with stone setts of size 600 to 1200 mm long, 150 to 300mm wide and 75mm deep and sides dressed; bedded in cement mortar 1:3, 20mm thick; joints grouted in cement mortar 1:2 with an admixture of metallic floor hardner, 5% by weight of cement and struck flush complete all as specified and as directed.

All as per ser item No.1.06 here-in-above, but except stone setts, complete all as specified and as directed. Note- The serviceable stone setts obtained from Serial item No.1.05 shall be reused after removing motar, cleaning with water, etc.complete.

Dismantling timber scantlings in any position in fillets, rails, posts, rafters , purlins, etc. under 40 sq. cm in section (framed / unframed work) complete all as specified and as directed.

Material and Labour for dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish/ demolished material outside defence land, complete all as specified and as directed .

Dismantling of brick work or stone masonary, precast cement concrete walling built in cement mortar including all quoins, arches, pillars etc., complete all as specified and as directed.

Material and labour for brick work with subclass ‘B` old size bricks, straight or curved on plan exceeding 6 metre mean radius built in cement mortar (1:6), complete all as specified and as directed.

Material and Labour for Brick work with sub class ‘B’ bricks (Except Bricks), straight or curved on plan exceeding 6 metre mean radius, built in cement mortar (1:6) , complete all as specified. ( Note- The serviceable bricks obtained from Serial item No- 1.10 will be used after removing motar, cleaning the bricks with water, etc.)

Material and labour for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:4 complete all as specified and as directed.

Material and labour for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:4 but except stone complete all as specified and as directed. Note- The serviceable stones obtained from Serial item No-1.10 will be used after removing motar, cleaning with water, etc.)

Demolition of cement concrete (unreinforced) in ground floor and pavings not exceeding 15cm thickness (below or above ground level) and removal the rubbish/ demolished material outside defence land, complete all as specified and as directed.

Material and labour for plain cement concrete 1:2:4 type B-1 (using 20mm graded mechanically crushed stone aggregate) as in surface channels and drains, complete all as specified and ditected.

Material and Labour extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds , mitred /stopped ends etc., complete all as specified and directed.

Material and Labour for providing Precast reinforced Cement Concrete 1:2:4 type B1 using 20mm graded aggregate as in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in cement mortar 1:4 complete with joints to match, except blocks or slabs, complete, all as specified and as directed..

Material and labour for hammer dressing to granite or trap stone with maximum depression from a straight edge held against the surface not exceeding 40mm dressing, complete all as specified and as directed .

Demolition of cement concrete (reinforced) in ground floor and pavings not exceeding 15cm thickness (below or above ground level) and removal the rubbish/ demolished material outside defence land, complete all as specified and as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs any thickness, including cover fillets complete all as specified.

Material and labour for providing cement concrete 1:2:4 Type B1 using 20mm graded aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed.

Cutting chases,pinning inmaking good to facings where required and pointed in cement mortar 1:3 to ends or edges of landings, steps, cills, shelves, etc. and cutting chases for concealed water tubing or concealed conduit wiring, etc . cutting not exceeding 10cm girth in brick and making good in cement mortar 1:3 complete all as specified and as directed.

Supplying & Fixing for Pre-painted galvalume aluminuim zinc coating GI based corrugated steel sheet 0.50mm thick, conforming to IS-15961 of any colour having tensile strength of 550 MPa as in roof covering/cladding to wall, fixed with self tapping screws, complete, all as specified and as directed .

Supplying & Fixing for Pre-painted galvalume aluminuim zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 MPa as in roof covering/cladding to wall, fixed with self tapping screws, complete, all as specified and as directed .

Material and labour for Second class hardwood (Hollack) plain fillets, square, rectangular or triangular in section of area exceeding 6 Sq. cm and not exceeding 13 Sq. cm, clean sawn, secured with nails or brads, complete all as specified and as directed.

Material and labour for Second class hardwood plain fillets, square, rectangular or triangular in section of area exceeding 13 Sq. cm and not exceeding 25 Sq. cm, clean sawn, secured with nails, complete all as specified and as directed.

Supply and fixing IInd class (hollock) factory made 35mm thick glazed skelton shutters, open rebated and prepared to receive glass, gauge etc. divided into squares edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass/gauge etc. with sizes of members of shutters as specified in para 8.24(a) of SSR 2009 (Part I), complete all as specified and as directed.

Supply and fixing 30 mm thick 2nd class hardwood skeleton shutters, open rebated and prepared to receive wire cloth, glass etc. (with or without sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass, wire cloth etc., sizes of members of shutters as specified in SSR Part-I section 8 clause 8.24(b), complete all as specified.

Supplying and Fixing for factory made 35mm thick, 2nd class HW, plain framed, panelled shutters (two panel) with lock rail and panel of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS:1003 (Part I), kiln seasoned and chemically pressure treated, complete, all as specified and as directed.

Supply and fixing factory made flush shutters 35 mm thick, solid core construction, with block board core and and both faces are covered with decorative face veneer with lipping/frame to match, ISI marked complete all as specified and as directed.

Taking down chowkats or frames with shutter area not exceeding 1.50 Square metre (w/o taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish complete, all as specified and as directed.

Taking down chowkats or frames with shutter area exceeding 1.50 Square metre and not exceeding 4.00 Square metre (w/o taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish , complete all as specified and as directed.

Taking down window shutters of any description but not exceeding 1.00 Sq.m each from chowkhat, complete all as specified.

Taking down shutters of any description exceeding 1.00 Sq.m but not exceeding 2.00 Sq.m each, from chowkhat complete all as specified and as directed .

Supply and fixing for 2nd class hard wood plain, solid straight chowkats and frames, wrought framed rebated on the solid, rounded or chamfered put together with glue pinned at joints, complete all as specified and as directed .

Supply and fixing mild steel works in bands, straps, supports, stays, bolts, hooks, hold fasts etc, similar articles conforming to Fe-290.Gde-E-165, complete all as specified and as directed.

Material and Labour for mild steel TMT bars of 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete, all as specified and as directed .

Material and Labour for mild steel TMT bars of 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete, all as specified and as directed.

Supply and fixing "RAJSHRI" BRAND 25mm thick factory made White Colour Rigid Glazed Solid UPVC Window Shutter consisting of frame made out of mild steel tube of 19 gauge of size 15mm x 15mm (style, top, bottom rail) .Mild steel frame of 'C' Channel of size 62mm x 25mm x 50mm with one factory coat of steel primers and covered with 4.25mm thick sheet (4mm(±0.3) UPVC foam sheet laminated with 0.25mm rigid PVC sheet of density 900 kg/cum.) White colour, rigid heat moulded UPVC.. Glass panel and Wire mesh shall be fitted externally in the clear space available between stiles and rails and fixed using window shutter UPVC (Rigid) beading of size 12mm x 8mm complete as per direction of Engineer-in-charge and manufacturer's specification. Note- Glazing and, wire mesh shall be measured and paid for separately.

Supply and fixing aluminum anodized, barrel tower bolt of extruded section 125mm long, ISI marked, complete all as specified and as directed.

Supply and fixing aluminum anodized, barrel tower bolt of extruded section 150mm long, ISI marked, complete all as specified and as directed.

Supply and fixing for aluminum anodized barrel tower bolt of extruded section 200mm long, ISI marked, complete all as specified and as directed.

Supply and fixing 300 mm aluminum anodised sliding door bolt, ISI marked, with hasp, staple (bolt type) complete with clamps bolt not less than 16mm dia and fixing clips of sheet, cast or extruded section and fixing bolts an sliding bolt of extruded section or cast aluminum alloy, complete all as specified and as directed.

Supply and fixing 250 mm aluminum anodised sliding door bolt, ISI marked, with hasp, staple (bolt type) complete with clamps bolt not less than 16mm dia and fixing clips of sheet, cast or extruded section and fixing bolts an sliding bolt of extruded section or cast aluminum alloy, complete all as specified and as directed.

Supply and fixing for butt hinge ,ISI Marked ,125mm size, medium weight, cold rolled mild steel complete, all as specified and as directed.

Supply and fixing for butt hinge ,ISI Marked ,100mm size, medium weight, cold rolled mild steel complete, all as specified and as directed.

Supply and fixing for butt hinge ,ISI Marked ,75mm size, medium weight, cold rolled mild steel complete, all as specified and as directed.

Supply and fixing continuous (piano) hinge, mild steel bright finish or electro galvanised, width of flap when open 30 mm complete all as specified and as directed.

Supply and fixing mild steel helical door spring 200 mm long fixed with screws to wooden chowkhats or welding to steel chowkhats, complete all as specified and as directed.

Supply and fixing 100mm cast iron or malleable cast iron handles, cast type, stove enamelled black complete all as specified and as directed.

Supply and fixing for ISI Marked 150 mm long, aluminium handle, cast type, anodized, complete, all as specified and as directed.

Supply and fixing for ISI Marked 100 mm long, aluminium handle, cast type, anodized, complete, all as specified and as directed.

Supply and fixing ( in repair), mild steel 25mm dia, 1.6mm thick, PVC coated, fancy type, heavy duty drapery rod, complete all as specified.

Supply and fixing (in repair), fancy type finials (latto) or wall end socket or brackets suitable for 25mm dia drapery rod, complete all as specified.

Material and labour for machine cut kota stone slab 18-20 mm thick (of size not less than (55 cm x 55 cm) laid in flooring and jointed & pointed with grey cement slurry mixed with pigment to match shade of the slab including cutting waste, rubbing and polishing (Granite finish) over and including cement screed bed 20mm thick in cement mortar (1:3) base , complete all as specified and as directed.

Material and labour for machine cut kota stone slab 16-18 mm thick laid on vertical surface and jointed & pointed with grey cement slurry mixed with pigment to match shade of the slab including cutting, waste, rubbing and polishing (Granite finish) but as in skirting over and including 10mm thick plaster in cement mortar (1:3) on brick work or concrete surfaces complete, all as specified and as directed.

Material and labour for PCC 1:2:4 type B-1 (using 20 mm graded mechanically crushed stone aggregate), 50mm thick, as in plinth protection/PCC path and paving, laid in panels of area not exceeding 2.00 sqm with 6mm wide joints filled with mastic (using bitumen and sand mixture applied hot in the ratio of 1:3 by weight) formed at the end of each panel and change in direction of plinth protection/PCC Path and paving and finishing the top surface even and smooth without using extra cement complete all as specified and as directed.

Material and labour for 40mm thick PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in floor finished even and smooth with out using extra cement complete all as specified and directed .

Material and labour for Glass dividing strips, 3mm thick and 38mm in width inserted in position conform to design complete all as specified and directed .

Material and labour for 25mm thick PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in floor complete all as specified and as directed.

Material and labour for 75mm thick PCC 1:4:8 type D-2 (using 40 mm graded mechanically crushed stone aggregate) as in sub base to floor, complete all as specified and as directed

Material and labour for premium quality, glazed coloured ceramic tiles 300 x 450 x 7mm thick on vertical surfaces of walls including 10mm thick rough finished plaster in cement mortar (1:3) set jointed in neat cement slurry and pointed in coloured cement to match complete, all as specified and as directed.

Material and labour for premium quality, joint free, non skid coloured ceramic tiles (Square/rectangular) , area of each tiles exceeding 0.06 sqm and not exceeding 0.11 sqm and 7 to 8 mm thick as in floor, set and jointed in neat cement slurry @ 3.00 kg/Sqm and pointed in white or coloured cement to match the surface over and including cement screed bed 15mm thick in cement mortar (1:4) , complete all as specified and as directed.

Supply and fixing chequered cement concrete tiles with grey cement and pigment , rubber moulded with laquer polish for extra shine, size 300 mm x 300 mm x 22-25 mm thick, ISI marked, coloured, set jointed and pointed in neat cement slurry over and including 20 mm thick (average thickness) cement screed (1:4) base, complete all as specified and as directed.

Material and labour for premium quality, joint free, non skid coloured ceramic tiles (Square/rectangular) , area of each tiles exceeding 0.18 sqm and not exceeding 0.38 sqm and 7 to 8 mm thick as in floor, set and jointed in neat cement slurry @ 3.00 kg/Sqm and pointed in white or coloured cement to match the surface over and including cement screed bed 15mm thick in cement mortar (1:4) , complete all as specified and as directed.

Material and Labour for vibratory compacted, precast cement concrete, coloured (other than grey), rubber moulded , interlocking designer paver blocks( double glossy) in any and shape, confirming to IS-15658-2006 of 60mm thickness, M-35 grade in path, hard standing, etc. laid over and including 25 mm thick bedding layer of sand complete, all as specified and as directed.

Material and labour for 3.20/3.30mm thick linoleum, plain coloured, laid dry in floors including stretching, cutting and fitting and sealed down with an approved adhesive, complete all as specified and as directed.

Taking down cement plaster of any description, thickness and in any position including raking out joints, hacking for key, scrubbing down with water etc , and removal the rubbish/ demolished material outside defence land, complete all as specified and as directed.

Material and Labour for 15mm thick rendering in two layers on fair faces of brick work or concrete surfaces in cement mortar 1:4 mixed with WPC @2% by weight of cement or as per manufacturer’s instructions, finished even and fair, complete all as specified and as directed. (Note : WPC shall be measured and paid separately)

Supply only integral water proofing compound, complete all as specified and as directed.

Dismantling of boarding, any description, fixed in any position with nails, complete all as specified

Material and labour for particle board, 19/20mm thick, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work complete all as specified and as directed.

Material and labour for 1.5mm thick decorative laminate type 1, of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer`s instructions complete all as specified and as directed.

Material and Labour for hardwood IInd class weather boarding, clean sawn, plain, 20mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm laps complete all as specified and as directed.

Description all as per serial item No.1.76 above but except boarding. ( Note- The serviceable boarding obtained from Serial item No- 1.72 will be used after repair.)

Material and labour for 20mm thick boarding, hardwood IInd class, planed one side with butt joints, fixed with nails in any situation (except flooring and skirting) complete all as specified and as directed.

Material and labour for 40mm thick boarding, hardwood IInd class, planed one side with butt joints, fixed with nails in any situation (except flooring and skirting) complete all as specified and as directed.

Material and labour for 6mm thick (5 ply) plywood, grade BWR, type BB, fixed with screws to timber frame work complete all as specified and as directed.

Material and labour for 6mm thick (5 ply) veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one faces, fixed with screws to timber frame work on walls, complete all as specified and as directed .

Material and labour for 6mm thick (5 ply) veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one faces, fixed with screws to timber frame work on ceiling, complete all as specified and as directed .

Supply and fixing 2nd class hard wood fillets, clean swan, bull nosed, chamfered or rounded on one face, sectional area exceeding 3 Sq. cm but not exceeding 6 Sq. cm, fixed with nails or brads including two coat of painting over a coat of pink primer after preparation of new fillets surface, complete all as specified.

Supply and fixing llnd class hardwood, 100mm x 75mm moulded handrails rounded or shaped with splayed faces in straight lengths and fixed complete all as specified and as directed.

Supply and fixing 40mm,llnd class hardwood wrought treads with rounded nosings, with 25mm wrought risers on tongued both edges, glued, wedged and blocked complete all as specified and as directed.

Dismantling timber scantling 40 Sq. cm and over in section, in any position of unframed/ framed work complete, all as specified and as directed .

Material and labour for 2nd class hardwood clean sawn in scantlings, in any position in framed work, complete all as specified and directed

Description all as per serial item No. 1.86 above but except timber, complete all as specified and directed

Supply and fixing in repair 8mm thick prelaminated wooden flooring over existing concrete surface comprising of the following specifications complete, all as specified and directed by Engr-in-charge. (i) Cleaning of concrete surface with mechanical means i.e. steel wire brush/air blower etc. and remove all loose /unsound material, dirt, dust etc, levelling the concrete surface and allow air dry to acheve moisture free surface. (b) Laying 125 micron polythene sheet ( as vapour barries) over the leveled concrete surface. (c) Laying 5mm thick thermocole sheet over polythene sheet. (d) Laying 8mm thick prelaminated wooden flooring as per manufacturer instruction. .Note :- The flooring shall be carried out by the manufacturer or his authorised applicators. i

Material and labour for 2-3mm thick wall care putty on new plastered surface complete all as specified and directed

Material and labour for preparation of old treated surfaces of walls and applying two coats of oil bound distemper, complete all as specified and as directed

Material and labour for two coat of cement base paint over a coat of alkaline resistant primer on newly plastered surface including preparation of surface of wall complete all as specified and as directed.

Material and labour for complete removal of existing treatment on surfaces of walls by using appropriate technique as approved by Engr-in-charge for complete removal of all layers of old treatment and reaching upto old plastered surface and applied two coat of cement base paint over a coat of alkaline resistant primer including preparation of surface complete all as specified and as directed.

Preparation of old painted wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed.

Preparation of old treated wood and wood base surfaces of any description over 10cm width or girth and applying one coat of varnish, complete all as specified and as directed.

Material and labour for preparing new or previously untreated wood and wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

Preparation of old painted steel surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed.

Material and labour for two coats of synthetic enamel paint on steel surfaces over a coat of red oxide primer including preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth, complete all as specified and as directed.

Material and labour for preparing new zinc (or galvanised) surfaces to receive painting, by coating with mordant solution including washing and cleaning, etc. and applying two coat of synthetic enamel paint, complete all as specified and directed..

Supply and fixing water storage tank 1000 ltr capacity HDPE triple layer, white coloured, conforming to IS , fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm high pressure with polythene float and flynut, screwed and suitable for iron pipe 20 mm bore, complete all as specified and as directed.

Supply and fixing in repair, vitreous china wash hand basin white flat back of size 550x400mm with padestal including CI brackets embedded in wall in CM 1:4, PVC waste pipe, PVC connections and chromium plated waste coupling, etc.,complete all as specified and as directed.

Supply and fixed in repair, vitreous china wash down water closet pedestal pattern, coloured including connection to trap and to flushing pipe with ‘P’ or ‘S’ trap, plastic water closet seat cover with mild steel chromium plated hinges complete, all as specified and as directed.

Supply and fixing 10 litre capacity, low level, virgin polypropylene cistern, ISI marked, coloured complete with PVC bend/flush pipe and making all connection including taking down existing high or low level unerviceable flushing cistern and making good the disturbed surface to match with the existing surface complete all as specified and as directed.

Taking up or down steel tubing and connections for 15mm dia including cleaning for refixing or removal to store complete all as specified and as directed .

Taking up or down steel tubing and connections for 20mm dia including cleaning for refixing or removal to store complete all as specified and as directed.

Supplying and fxing for ISI Marked, 15mm bore `Medium grade` GI tubing with all fitting and fixed complete to walls and ceilings or laid in floors, complete, all as specified and as directed.

Supplying and fixing for ISI Marked, 20mm bore `Medium grade` GI tubing with all fitting and fixed complete to walls and ceilings or laid in floors, complete, all as specified and as directed.

Fixing only in repairs 15mm dia GI tubes, any grade, to walls and ceilings or laying in floors complete all as specified and as directed. Note: Old tubes reteived from serial item No 2.04hereinbefore shall be reused in this item.

Fixing only in repairs 20mm dia GI tubes, any grade, to walls and ceilings or laying in floors complete all as specified and as directed. Note: Old tubes reteived from serial item No 2.05hereinbefore shall be reused in this item.

Supplying and fixing (in repair), angle cock, 15 mm dia , brass, fancy type, chromium plated, ISI marked, screwed down, high pressure with capstain head screwed both ends for iron pipes or for unions, complete all as specified and as directed. Note- Contractor will submit to Engineer-in-Charge a guarantee certificate from manufacturer before claiming payment.

Supplying and fixing stop cock 15mm dia, cast copper alloy, ISI marked, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or unions, complete all as specified and as directed by the Engineer-in-Charge. Note : (i)Contractor will submit to Engineer-in-Charge a guarantee certificate from manufacturer before claiming payment.

Supplying and fixing PVC connections 60cm long and 15mm dia with PTMT nuts and PVC washers on both ends, complete all as specified and as directed.

Supply and fixing ( in repair), PVC waste pipe for wash hand basin/urinals, 32mm dia and 80 cm long plain pipe, complete all as specified and as directed.

Supplying and fixing in replacement 15mm bore pillar tap,chromium plated cast copper alloy with capstan head, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ complete all as specified and as directed. Note- Contractor will submit to Engineer-in-Charge a guarantee certificate from manufacturer before claiming payment.

Supply and fixed in repair vitreous china bowl urinal white flat back of size 465x355x265mm with grating and union for discharge pipe excluding flushing cistern , flush pipe and waste pipe but including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws pointing around urinal back in cement,complete all as specified.

Supply and fixing in repair, aluminium composite panel clading of aproved make- Alstone/Aucomat/Alpolic (as per technical specification ) including necessary aluminium frame work either curved or straight or circular in plan. The aluminum composite panel shall be of 3mm thick thermoplastic core of anti-oxidant LDPE+HDPE (Virigin Core) sanwitched between 2 layers each 0.5mm thick aluminium alloy sheet (alloy grade 1100 of ASTM B-209) making a total panel thickness of 4mm . The surface finish shall be PVDF coat of 30 micron over e base polyster coat on top and services coat on the reverse with chrome /alkyd of 6-7 microns coating shall confirm to ASTM D-2244-93 and ASTM D 523-89 for colour retention and colk resistante ACP shall be fixed on especially designed aluminium frame work as per manufacturer's instructions with horizontal and vertical members of extruded aluminium section of size 25x38x1.6mm sheet to supplied in width of 1220mm and as per specifications including stainless steel fastening system making grooves applying non staining and non streaking weather sealent (Alstone WS-600/900 or equivalent as approved ). all as specified and directed.

Supply and fixing 75mm dia UPVC, soil waste drain pipe, type ‘B’ , conforming to IS 13592-1992, single socketed, in any length with rubber rings joints or jointed with solvent cement joint, fixed to wall with stack clamps 50mmx5mm flat iron and 16 mm dia round iron stays, including bolts and nuts complete all as specified and as directed . (Note- Rubber rings for pipes and fittings shall be confirm to IS 5382-1985)

Supply and fixing for sheet glass 3mm thick, ordinary quality , in square not exceeding 0.5 sqm in each pane and glazing with oil putty to steel window and with wooden beads to wooden shutters including solar control film 25 micron, reflective type sticked to glass panes as per instructions of manufacturers, complete all as specified and as directed.

Supply and fixing for sheet glass 4mm thick, ordinary quality , in square not exceeding 0.5 sqm in each pane and glazing with oil putty to steel window and with wooden beads to wooden shutters, complete all as specified and as directed.

SCHEDULE A PART II (INTERNAL ELECTRIFICATION)

Taking down carefully any type point wiring (light, fan, socket or power) complete with fittings such as switches ceiling roses, pendants, regulators, sockets tube light fitting with all accessories etc. removal of materials from site and making good the disturbed surfaces of wall, floors, ceiling etc to match with the existing surfaces complete, all as specified and as directed.

Material and labour for Point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable flame retardant low smoke (FRLS) , 1100 volt grade with multi stranded copper conductor drawn through and incuding medium grade , ISI marked PVC casing caping not less than 32 mm width , 10 mm depth with accessories fixed on wall/ceiling surface and incuding provision of 1.50 Sqmm single core PVC insulated , unsheathed cable flame retardant low smoke (FRLS) , 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with including mild steel sunken box or pressed steel terminal boxes made out of 1.6 mm thick mild steel sheet metal conforming to IS-5139(pt-I) of 1969 and IS:14772-2000 with earth dolly and coated with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally including provision of new 3 mm thick plastic laminated sheet top cover extended up to 25 mm over sunken box for housing the switches , socket outlets, fan regulators etc. with brass screws and brass washers and making good the disturbed surfaces as per existing for one light/fan any type/bell point controlled by one switch. Note :- Switch, socket and fan regulators to be measured and paid for separately .

Description all as per Srl item No.3.02 here in before but for socket outlet point 5 Amp on same board.

Description all as per Srl item No.3.02 here in before but for socket outlet point 5 Amp on Independent board complete, all as specified and as directed.

All as per the description of Serial Item No 3.02 above, but with 2.50 Sq mm un-sheathed multistranded cable for one socket outlet 15 Amps independent including continuous copper earth wire, PVC insulated of 2.50 Sq mm size complete, all as specified and as directed . (Switch, Socket shall be measured and paid separately)

Supply and fixing switch piano 5/6 Amps, flush button type, single pole, one way, 240 volt , AC supply, ISI Marked, complete all as specified and as directed.

Supply and fixing switch piano 15/16 Amps, flush button type one way 240 Volts, 50 Hz , AC supply, ISI Marked, complete all as specified and as directed.

Supply and fixing switch piano, bell push, 6 Amps , flush type, 240V, 50 Hz AC supply, ISI Marked, complete all as specified and as directed.

Supply and fixing socket outlet 5 pin 5/6 amps, 240 volt. flush type, AC supply, ISI Marked, complete all as specified and as directed.

Supply and fixing socket outlet 2 in 1, 6 pin 6 /16 Amp and multi pin flush universal shuttered type, 240 volt, AC supply, ISI Marked, complete all as specified and as directed.

Supply and fixing switch socket combination, 5 Amp, 2 in 1, single pole one way ,230 volts, flush type, AC supply, ISI Marked, complete all as specified and as directed.

Supply and fixing switch socket combination, 5/16 Amp, 5 in 1, single pole one way ,230 volts, flush type, AC supply, ISI Marked, complete all as specified and as directed.

Supplying and fixing Television (TV) socket, ISI Marked, complete all as specified and as directed.. Make:Havells Cat Part No. AHEKTOE001 or equivalent model in makes mentioned for Group 2 in Appendix 'B' of tender document .

Supplying and fixing Telephone socket, ISI Marked with top connector, complete all as specified and as directed by the Engineer-in-Charge. Make: Havells Cat Part No. AHEKRWW111 or equivalent model in makes mentioned for Group 2 in Appendix 'B' of tender document .

Supplying and fixing the ceiling rose, three terminal ISI marked surface backlit, complete all as specified and as directed.

Supply and fixing lamp holder, PVC/polycarbonate type with back plate suitable for batten fittings, ISI Marked, complete all as specified and as directed.

Supply and fixing fan regulator electronic step type(Socket type), 120 watt, 230 Volts, 50 Hz, AC supply suitable for ceiling fan any type/make/sweep complete all as specified.

Supplying and fixing in replacement, LED bulk head light fitting 1x10 watt with lamp holder(1x10W) ABS housing, IP65 and connecting up with twin core twisted flexible copper conductor cable of suitable size from ceiling rose to connector of light complete, all as specified and directed. Make: Bajaj Cat Part No. BIBWP 10WLED or equivalent model in makes mentioned for Group 2 in Appendix 'B' of tender document .

Supplying only pin type LED bulb, 15 watt pin type, ISI marked, suitable for batten holder complete, all as specified and directed. Make: Havells Cat Part No. LHLDEREEMK8X015 or equivalent model in makes mentioned for Group 2 in Appendix 'B' of tender document .

Supplying only pin type LED bulb, 10 watt pin type, ISI marked, suitable for batten holder complete, all as specified and directed. Make: Havells Cat Part No. LHLDERHEML8X010 or equivalent model in makes mentioned for Group 2 in Appendix 'B' of tender document .

Supply and fixing in replacement indoor decorative 20 watt LED tube light luminarie, extruded aluminium housing with polycarbonate diffuser and integrated electronic driver , AC 220-240 Volts, 50Hz including lamp ( Lamp type LED tube light 1x 20 Watt) and connecting up with three core 1.5 sqmm flexible copper conductor cable from ceiling rose to connector of light complete, all as specified and as directed. Make: Havells Cat Part No. ENDURALINEARNEOBS20WLED865SPCWH or equivalent model in makes mentioned for Group 2 in Appendix 'B' of tender document .

Supplying and fixing in replacement LED mirror light fitting with lamp, high output PMMA diffuser for glare free light, complete with all accessories internally prewired and connecting up with core twisted flexible copper conductor cable with suitable size, complete all as specified and as directed. Make- CG Ct Pt No- CDL-07-CDL or equivalent model in makes mentioned in Appendix 'B' of tender document .

Supply and fixing Jeta pro plus, die-cast aluminum housing, IP65 70W LED flood light fitting including high power LEDs suitable for highlighting architectural facade, highmast complete all as specified and directed. Make: Havells Cat Part No.JETANEOFL70WLED757LTG or equivalent model in makes mentioned for Group 2 in Appendix 'B' of tender document .

Supply and fixing exhaust fan 300mm size , ISI marked, AC single phase 230/240 volt ,steel body with louver, 1400 RPM and connecting with twin twisted copper conductor flexible of size 0.50 sqmm including cutting of existing wall and making opening in the existing wall for fixing exhaust fan, fixing nut bolts necessary for fixing exhaust fan and making good the disturbed surfaces and testing complete, all as specified and directed.

Supply and fixing exhaust fan 450mm size , ISI marked, AC single phase 230/240 volt ,steel body with louver, 1400 RPM and connecting with twin twisted copper conductor flexible of size 0.50 sqmm including cutting of existing wall and making opening in the existing wall for fixing exhaust fan, fixing nut bolts necessary for fixing exhaust fan and making good the disturbed surfaces and testing complete, all as specified and directed.

Supply and fixing ceiling fan of 1200 mm sweep, 230 volts, ISI marked, BEE 5 star rating, 50 Hz complete with down rod and fan clamp with rubber reel including connecting with 3 core copper conductor flexible cable of size 23/0.0076 from ceiling rose to connector of fan complete all as specified Make: Havells Cat Part No. ES-50 or equivalent model in makes mentioned for Group 2 in Appendix 'B' of tender document .

Supply and fixing geyser 25 litre capacity, BEE 5 star rating, vertical type including cement work, fixing bolts, making good the disturbed wall surfaces with the existing surface, water connection, electrical connection with three core PVC insulated copper conductor cable of 40/.0076 size complete, all as specified and as directed. Make: Havells Cat Part No. GHWAPTTWHO25 or equivalent model in makes mentioned for Group 2 in Appendix 'B' of tender document .

Supply and fixing MCB single pole, 240 volts, 50Hz , breaking capacity 10KA, B curve, 6 to 32 Amps, ISI marked, complete all as specified and as directed.

Supply and fixing MCB single pole and neutral, 240 volts, 50Hz , breaking capacity 10KA, B curve, 6 to 32 Amps, ISI marked, complete all as specified and as directed.

Supply and fixing MCB, Double pole, 415 volts, 50Hz , breaking capacity 10KA, B curve, 6-32 Amps, ISI marked, complete all as specified and as directed.

Supply and fixing MCCB three pole , 415 volts, 100 Amps, breaking capacity 16KA ,fixed type, ISI marked, complete all as specified and as directed.

Supply and fixing MCCB distribution board for Load line TPN, 6 ways, double door, 415 volts, with and including 200 amps rated bus bar, vertical type, IP 43 IK09 protection powder coated, suitable for MCCB as a in incomer and MCB's as out going with suitable size of MS cabinet 2mm thick and making all type of connections with suitable size of gland for incomer cable complete , concealed on the wall surface, making good the disturbed portion with adjoining surfaces to match with existing finish and taking down the existing DB's and MCB's any type complete all as specified and as directed.

Supply , insatallation, testing of SPN distibution board 04 way,double door , IP 43 , as per IS 8623 including 200 amps fully insulated copper bus bar, insulated neutral bar, earth bar, door earthing, reversible doors, PAN assembly for easy installation and also incoming and outgoing connections with suitable size of lugs/thimbles, concealed on the wall surface including taking down the existing DB's any type and description and making good the disturbed portion with adjoining surfaces to match with existing finish, complete, all as specified and as directed.

Supply , insatallation, testing of SPN distibution board 08 way,double door , IP 43 , as per IS 8623 including 200 amps fully insulated copper bus bar, insulated neutral bar, earth bar, door earthing, reversible doors, PAN assembly for easy installation and also incoming and outgoing connections with suitable size of lugs/thimbles, concealed on the wall surface including taking down the existing DB's any type and description and making good the disturbed portion with adjoining surfaces to match with existing finish, complete, all as specified and as directed.

Taking out old earthing complete and taking out old unserviceable earthing material and provision of new earthing complete with galvanised earth plate electrode 600mm x 600mmx 6mm thick surrounded by charcoal and salt, buried directly in ground vertically in a pit of depth not less than 2.25m below ground level with top edge of the earth plate not less than 1.5m below normal ground level, connected to 4.00 mm wire earth lead by means of bolts, nuts, checks nut and washers made out of galvanized iron or steel, earth wire protected by galvanized steel pipe 15mm dia (light grade) and connected to main switch or main control board all as shown in electrical plate No.3 of SSR Part-I & including necessary excavation and earth work. The rate also include charcoal & salt in alternate layers, 20mm dia GI pipe (light grade) for watering, protection pipe, funnel, wire mesh, RCC cover etc. complete, all as specified or indicated including testing on completion. Note : The rates for earth work in any type of soil, returning filling and removal, GI protection pipe, funnel, wire wesh, RCC cover, etc shall be deemed to be including in quoted rates. RCC cover shall be 50mm thick in 1:2:4 type B-1 using 8mm bars @10cm c/c both way.

Material and labour for sub main wiring with two single core flame retardant low smoke (FRLS) , PVC insulated unsheathed copper conductor cable 6.00 sqmm drawn through and including medium grade , ISI marked PVC casing caping not less than 32 mm width , 10 mm depth with accessories fixed on wall/ceiling surface with one additional PVC insulated , stranded copper conductor flame retardant low smoke (FRLS) of 4.0 sqmm,green colour for earth continuity conductor including taking down old unserviceable sub main wiring complete, all as specified and directed. Note- 2 run of 6.00 sqmm and 1 run of 4.00 sqmm cable with casing caping shall be measured as 1 unit.

Material and labour for sub main wiring with two single core flame retardant low smoke (FRLS) , PVC insulated unsheathed copper conductor cable 10 sqmm drawn through and including medium grade , ISI marked PVC casing caping not less than 32 mm width , 10 mm depth with accessories fixed on wall/ceiling surface with one additional PVC insulated , stranded copper conductor flame retardant low smoke (FRLS) of 10 sqmm,green colour for earth continuity conductor including taking down old unserviceable sub main wiring complete, all as specified and directed. Note- 3 run of 10.00 sqmm cable with casing caping shall be measured as 1 unit.

Supplying and fixing stop valves, 15 mm dia pipe, chromium plated, fancy type, ISI marked, screwed down, high pressure with capstain head, (concealed type) with long shank heavy body casted cap, screwed both ends for iron pipes or for unions, complete all as specified and as directed. (Make : ESSCO Cat No-DLX-526 or equivalent model in makes mentioned in Appendix 'B' of tender document ) Note- Contractor will submit to Engineer-in-Charge a guarantee certificate from manufacturer before claiming payment.

Supply and laying oor passing through pipes, XLPE insulated , screened, PVC bedded, galvanised steel strip or wire armoured electric power cable 1100 Volts grade with stranded aluminium conductor of size 10 Sq mm 2 core, complete, all as specified and as directed .

Material and Labour for medium grade , ISI marked, PVC casing caping not less than 32 mm width , 10 mm depth with accessories for TV cable and telephone cable etc, complete all as specified and as directed .

Excavating in trenches, not exceeding 1.50 metre wide and not exceeding 1.50m in depth for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. not exceeding 10 sq.m on plan and not exceeding 1.50m in depth and getting out in soft/loose soil, complete all as specified and as directed .

Returning filling in including spreding leveling watering and well ramming in layers not exc 25 cm each in soft/loose soil, complete all as specified and as directed .

Removing excavated materials to a distance not exc 50 m and depositing where directed at level n exc 1.5 above the starting points, complete all as specified and as directed .

Material and Labour for Fine and dry sand cushioning for underground cable by providing a layers of sand 8cm deep before laying and 15cm deep after laying the cable including tretching the cable, complete all as specified and as directed . Note - Punned thickness of sand layer shall be measured and paid to contractor.

Material and labour for sub class brick laid dry width wise across the cable in trenches for protection of cable complete all as specified.

Note:- Amount of credit of Rs. 88085.00 for retrieved materials as mentioned in Schedule of Credit Page No 55 of tender documents in pdf form which will be deducted offline while acceptance of tender.

M/S GHULAM RASOOL LONE AND SONS

M/S ABDUL MAJID LONE