SPECIAL REPAIRS TO ROOF OF THE BUILDING NO. P-65, P-101 AND P-63 AT NAD ALWAYE AND SPECIAL REPAIRS AND IMPROVEMENT TO MARRIED ACCOMMODATION BUILDINGS P-22 AND P-23 AT TS K.

Amount

Dismantling of corrugated, semi corrugated asbestos cement sheets in roof covering complete all as directed.

Dismantling of Plain or corrugated galvanised sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as directed.

Dismantling of rain water pipe including fittings in any position complete all as directed.

Dismantling of eves board and fixed in any position with nails complete all as directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for wind tie including fittings complete all as directed.

Dismantling of ceiling boards (fibre,pulp, insulation, etc.) or insulation boards/slabs and blankets any thickness, including cover fillets complete all as directed.

Dismantling of timber scantlings 40 sqcm and over in section, in any position complete all as directed.

Dismantling of fillets, rails, posts, rafters, purlins, etc. under 40 sqcm in section in any position complete all as directed.

Supply and fixing of Pre-painted galvalume aluminum zinc coating and GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Supply and fixing Pre -painted galvalume aluminium zinc coating and GI based plain sheet 0.50mm thick of any colour having tensile strength of 550mpa as in roof covering, fixed with self tapping screws complete all as specified and directed.

Supply and fixing of Steel work in purlin including welded with existing members tubular trusses including special shaped washer etc, complete using ERW or induction butt welded tubes confirming to IS:1161-1979 grade St-240 complete all as specified.

Supply and fixing of Mild steel work for wind tie for roof including drilling, bolting or riveting etc, and as in bands and hold fasts etc and similar small articles confirming to Fe-290 Grade E 165 complete all as specified and directed.

Material and labour for Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), clamps,hold fasts, wall ties ,plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles confirming to Fe-290 Grade-E-165 complete all as specified.

Supply and fixing of PVC (SWR) pipes 150mm bore single socketed in any length with rubber ring joints fixed to walls complete all as specified.

Supply and fixing of PVC (SWR) 150mm bore bends any radius including fittings complete all as specified.

Material and labour of Second class hard-wood in clean swan scantlings complete all as specified.

Ditto All as per Sl Item No 16, but except timber.

Material and labour for second class Hard wood exceeding 13 sqm and not exceeding 25 sqm sectional area in plain fillets square, rectangular or triangular in section, clean sawn, secured with nails or brads complete all as specified.

Material and labour of 4mm thick Non asbestos fibre cement building boards fixed in ceiling with screws complete all as specified and as directed.

Material and labour for 6mm thick Cover fillets of standard hard board, 40mm wide and fixing with all fittings complete all as specified and as directed.

Material and labour of second class Hard wood Weather boarding, clean sawn, plain, 20mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm laps with all fittings complete all as specified and as directed.

Material and labour for applying two coat creosote oil including preparing surfaces of new wooden surface complete all as specified and as directed.

Material and labour of one coat creosote oil including preparing surfaces of old wooden surface complete all as specified.

Material and labour of preparing new Zinc (or galvanised) surfaces to receive painting, by coating with mordant solution including washing and cleaning, etc, complete all as specified and directed.

Material and labour for preparation of new or previously untreated surfaces exceeding 10 cm width or girth applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Material and labour of two coat of synthetic enamel paint over a coat of red oxide primer not exceeding 10cm in girth/width complete all as specified and directed.

Material & Labour for preparation of new plastered surfaces and apply of three coats of white wash on ceiling surface complete all as specified and as directed.

Material and labour of two coat of synthetic enamel paint over one coat of pink primer including preparation of new wooden surface not exceeding 10cm in girth/width complete all as specified and directed.

Material & Labour for preparation of new surface with two coats of synthetic enamel painting over a coat of pink primer on wooden surface of any description, not otherwise described, over 10cm width or girth complete all as specified and directed.

Material and labour for applying one coat of synthetic enamel paint including preparation of old steel surface complete all as specified.

Material and labour of one coat of synthetic enamel paint including preparation of old wooden surface complete all as specified

Material and labour of one coat of synthetic enamel paint including preparation of old steel surface not exceeding 10cm girth/width complete all as specified.

Material and labour for applying one coat of white wash on wall surface including preparation of old treated surface complete all as specified.

Material and labour for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade(Company Depot Tinted) with silicon additives at 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied at 0.90 litre/10sqm including complete removal of existing treatment and preparation of surface complete all as specified.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed

Material and labour for point wiring complete with 2.5 sqmm PVC insulated (FRLS) unsheathed multi stranded copper conductor cable1100 volts grade through stove enameled steel conduit on wall/ceiling/Trusses including 2.5 sqm green colour code copper conductor (FRLS) or continuous earth wire. complete all as specified.

Supply and fixing of Flame proof switch rotary type with termination box in LM6, 16A, single pole 250V complete all as specified and as directed.

Supply and fixing of CIMFR certified LED flameproof batten suitable for twin T8 tube of 20Watt, Recommended for gas/Vapor group of llA & IIB and Zone 1 & 2, IP65 Protected including LED lamp 20W complete all as specified and as directed.

Material and labour for sub main wiring with 2 runs of 2.5 Sqmm PVC insulated unsheathed single core multi standard copper conductor cable, FRLS, ISI marked and one run of 2.5 Sqmm multi stranded insulated copper conductor cable, FRLS, ISI marked as earth continuity conductor drawn through stove enameled steel conduit of suitable size and all accessories, not less than 2mm thick, fire resistant, ISI marked and making good the disturbed surfaces of walls / floors / ceiling etc and including removing the existing aluminum sub main wiring cable, all as specified and directed. (Note:-Required for continuation of point wiring beyond 7.5 metrs)

Supply and fixing of single phase surge protection device type 1 & 2 tested for lightning impulse current 10/350 micro second 50 ka for phase to neutral and 125 ka for neutral to earth, surge protection device tested for nominal discharge current 8/20 micro second 20 ka phase to neutral voltage protection level, <=1.4kv, encapsulated spark technology for line to neutral for type 1 and metal oxide for varistor for type 2 line to neutral. LED indication in line to neutral pole in type 1 and flag indication in type 2 lines to neutral, response time for type 1 is less than 100 nano second and type 2 is less than 25 nano second, DIN rail mounted. Make:- OBO Better man Model No- MCD50B-OS 01 No (Artical No 5096861), MCD 125-B/NPE 1No, ((Artical No 5096865), and V20C/1 - 01 No (Artical No 5094684) all as specified and directed.

Supply and fixing of MCB distribution board made of thermoplastic polycarbonate IP65 in accordance with IEC61439-3, made of high quality Polycarbonate PC - GFS (shock proof, rust free, corrosion free, acid and chemical resistant, fire retardant, self-extinguishing, having high impact against mechanical load, made of halogen and silicon free recyclable material conform to ROHS directive 2002/92/EC, UV resistant according to IEC 61439-3, having high grade internally embedded gasket made of Polyurethane ( PUR ). Top and bottom cable entry via pre-moulded knockouts each DB Should have DIN channel for fixing MCBs/RCCBs/SPDs, earth and neutral terminal.For better safety enclosure should withstand glow wire test at 960 Deg. C in accordance with IEC 60 695-2-11 UL subject 94, should be flame retardant and self-extinguishing in nature. Degree of protection against mechanical load IK 08 (5 Joule) ) in accordance with accordance with EN IEC 62262 of size 400 x 333 x 129mm, 2 row 18 module complete all as specified and directed Make:- Hensel Cat No KV9118 M or equivalent in Spelsberg/Rittal

Supply and fixing in repairs RCCB, double pole, 25A, 30mA, 240V, all as specified and directed.

Supply and fixing in repairs RCCB, double pole, 40A, 30mA, 240V, all as specified and directed.

Material and labour for point wiring with 1.5 sqm PVC insulated unsheathed single core multi stranded copper conductor cable, FRLS, ISI marked drawn through stove enameled steel conduit of suitable size and all accessories, not less than 2mm thick, fire resistant, ISI marked including 2 mm thick and 4cm depth GI sheet pressed terminal box ( recessed) with 3 mm thick laminated hylam sheet top cover including 1.50 Sqm PVC insulated unsheathed multi stranded single core copper conductor FRLS, ISI marked cable as earth continuity conductor and making good the disturbed surfaces of walls, floors, ceiling etc, for One light point controlled by one switch complet all as specified and directed

Ditto all as per Serilal Item No 44 but for One 3 pin 5 Amps socket outlet controlled by one switch on independent board.

Ditto all as per Serilal Item No 44 but with 2.5 Sqmm cable for wiring and 2.50 Sqmm cable as earth continuity conductor for one 16 Amps switch socket outlet on independent board.

Supply and fix switch piano, flush type, 6 Amps, SP, one way, all as specified and directed.

Supply and fix in switch socket combination, 2/3 pin, 06 Amps, flush type all as specified and directed

Supply and fix switch socket combination 6 pin 6/16Amps, flush type, multipurpose all as specified and directed.

Supply and fix ceiling rose, surface type, Bakelite, 65x50mm, 3 terminals all as specified and directed.

Supply and fixing new generation energy saving and environmental friendly long life LED high bay light 80 watt in PDC housing suitable for industrial application, Lumen efficiency upto150 Lumen/Watt with IP66 Protection complete all as specified and directed.

Supply and fixing new generation energy saving and environmental friendly long life LED Street light 70/72 watt made up of pressure die cast aluminum housing with high power LED lumen efficiency 110 Lumen/Watt lighting source and lens embedded PC cover having Top Opening separate driver compartment with IP66 Protection and impact resistance of IK07 with 10KV Built-in Surge protection device complete all as specified and diercted.

Material and labour for sub main wiring with 2 runs of 1.5 Sq mm PVC insulated unsheathed single core multi stranded copper conductor cable, FRLS, ISI marked and one run of 1.5 Sq mm multi stranded insulated copper conductor cable, FRLS, ISI marked as earth continuity conductor drawn through and including steel conduit of suitable size and all accessories, not less than 2mm thick, fire resistant, ISI marked and making good the disturbed surfaces of walls / floors / ceiling etc and including removing the existing aluminum sub main wiring cable, for point wiring beyond 7.5 metres complete all as specified and directed.

Supply and fix in repairs MCB SP 6 to 32 Amps, 'C' series all as specified and directed.

Supply and fix in repairs MCB SPN 25-32 Amps 'C' series all as specified and directed.

Supply and fix in repairs MCB SPN 40 Amps 'C' series all as specified and directed.

Material and Labour in replacement of test terminal block made of gun metal or phosphorus bronze size 75x75x25 mm drilled and screwed including 3 No’s 8mm dia 25mm long hexagonal head screws complete all as specified.

Supply and fix in replacement GI strip 32 x 6 mm with saddles/fasteners/insulators and fixing screws etc for roof and down conductors above ground complete all as specified and directed.

Supply and fix in replacement single pointed aluminum rod 12mm dia 300mm long complete all as specified and directed.

Material and labour for Earthling with galvanized MS earth plate of size 600 x 600 x 6 mm thick buried directly in ground not less than 2.25 metre below ground level, earth plate placed on all side with charcoal mixed with salt to a thickness of 150 mm in layers, connected by GI earth strip of size 32 x 6 mm thick, soldered and reverted to earth plate, GI earth strip will be protected by using 40mm bore GI pipe (light grade) earth plate to transformer body, LT feeder pillar box, and neutral of transformer etc complete. The earthling includes Plain Cement Concrete pit chamber, Reinforced Cement Concrete pit cover and frame, watering pipe 20 mm bore, funnel with wire mesh with necessary earth work including disposal of surplus soil to a distance not less than 50 metre etc complete all as specified and shown in electrical plate No 3 of SSR Part I - 2009 complete all as specified and directed. Note: - Main earthling lead from earth plate to test point & up to 7.5 Metre to be provided. The cost for the same shall be deemed to be included in the above quoted rate.

Dismantling of old treated APP roof treatment of any type including tiles, screed bed complete all as per site condition and as directed by Engineer in charge.

Material & Labour for rendering 15mm thick on fair faces of concrete surfaces in Cement Mortar 1:3 finished even and smooth without using extra cement with using WPC complete all as specified and directed. Note: WPC will be measured and paid separately.

Supply only integral water proofing compound.

Material & Labour for cleaning and preparation of old or new surfaces and applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 Kg per Sqm complete all as specified and directed.

Material & Labour for 3mm thick APP based Polymeric membrane minimum weighing 3 Kg/Sqm and minimum reinforced with Polyster nonware fabric (not less than 150 Gm/Sqm) laid on primed surface by forced applied complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided complete all as specified and directed.

Material & Labour for reinforced cement concrete 1:2:4 Type B1 using 20 mm graded stone aggregate as in slab support on wall, column etc, complete all as specified and directed.

Material & Labour for RCC type B0 1:2:4 using 12.5 mm graded aggregate in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

Material and Labour for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exceeding 200mm thick complete all as specified and directed.

Material and Labour for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc, also splays between floors and beams etc, complete all as specified and directed.

Material and Labour for TMT steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding complete all as specified and directed.

Material and Labour for coloured joint free Ceramic tiles Matt finish 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors over 15mm thick screed bed in cement Mortar 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the existing surface complete all as specified and directed.

Ditto all as per Serial Item No 74, but in skirting over 10mm thick screed bed in cement mortar in 1:4.

Material & Labour for Non - skid coloured Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors over 15mm thick screed bed in Cement Mortar in 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the existing surface complete all as specified and directed.

Material & Labour for joint free Glazed ceramic coloured tiles in vertical surface 450X 300X 7mm thick over screed bed in 10mm thick CM 1:4 set and jointed in neat cement slurry and pointed in white or colour cement to match with the existing surface complete all as specified and directed.

Material & Labour for Granite (of any type) tiles 20mm thick machine cut over 20mm thick screed bed in Cement Mortar 1:6 ,bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed.

Demolition of concrete in ground floors and paving not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed.

Material & Labour for 75mm thick PCC 1:3:6 Type C2 40mm graded aggregate finished even and smooth without using extra cement as in plinth protection complete all as specified and directed.

Material & Labour for Pre-cast cement concrete block masonry type C1 1:3:6 (20mm graded aggregate) with solid blocks, not exceeding 10 cm in width and setting in mortar 1:4, complete all as specified and as directed by Engineer in Charge.

Taking down cement plaster on brick or stone wall etc including raking out joints, hacking for keys, scrubbing down with water etc, complete all as specified and as directed

Material & Labour for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and as directed

Material & Labour for rendering 10mm thick in CM 1:4 on fair faces of brick work or concrete surfaces including finished even and smooth without using extra cement complete all as specified and as directed.

Material & Labour for rendering 10mm thick in CM 1:3 on fair faces of concrete ceiling surfaces including finished even and smooth without using extra cement complete all as specified and as directed.

Material & Labour for preparation of new plastered surfaces of wall and apply of two coats of oil bound distemper over a coat of primer complete all as specified and as directed.

Material & Labour for preparing old distempered surfaces of walls by and applying one coat of oil bound distemper complete all as specified and directed.

Material & Labour for preparation of old surfaces of ceiling and applying one coats of white wash complete all as specified and directed.

Taking down chowkat with shutters (without taking off shutters from the frame) exceeding 1.5 Sqm and not exceeding 4 Sqm complete all as specified and directed.

Taking down chowkat with shutters not exceeding 1.5 Sqm complete all as specified and directed.

Taking down shutter exceeding 1 Sqm and not exceeding 2 Sqm complete all as specified and directed.

Refixing of shutters in same opening of any description exceeding 1 Sqm and not exceeding 2 Sqm complete all as specified and directed.

Material & Labour for solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed.

Supply & Fix factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS. tubes for top & bottom rails, MS. frame shall be covered with heat molded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Paneling of plain colour PVC sheet to be fitted in the MS. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed.

Material & Labour for second class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed.

Supply & Fix second class Hard Wood framed, paneled shutter 35mm thick (one panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces, The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

Supply & Fix second class hard wood Glazed and skeleton shutters 35mm thick open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a), supplied and fitted to chowkats complete all as specified and directed.

Supply & Fix 25mm thick Flush shutters, solid core construction, with block board core and plywood face panels, one face is covered with decorative face veneer with liping/frame to match and other face commercial type for cupboard complete all as specified and directed.

Supply & Fix Aluminium anodised, barrel tower bolts of extruded section and fixed of size 150mm complete all as specified and directed.

Supply & Fix Aluminium alloy, anodised, sliding door bolt of size 250 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

Supply & Fix mild steel butt hinges 100mm, medium weight complete all as specified and directed.

Supply & Fix extruded aluminium bow handles 150mm, fabricated type, anodised complete all as specified and directed.

Supply & Fix Floor door stopper of aluminium alloy body of size 140mm and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

Supply & Fix MS 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

Supply & Fix 20mm thick second class hard wood in shelves of built in cupboards and similar works both size edges tongued and grooved or rebated complete all as specified and directed.

Supply & Fix Continuous (piano) hinges, mild steel, bright finish or electro galvanised complete all as specified and directed.

Supply & Fix 40mm dia, cupboard knobs fixed with nut, screw and washer of brass polished bright finished complete all as specified and directed.

Supply & Fix 100mm size Hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

Supply & Fix stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

Material & Labour for preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, not otherwise described, and treated with tar or coal tar black paint treating end of posts, back of chowkats etc, area treated exceeding 0.1 Sqm but not exceeding 0.5 Sqm each complete all as specified and directed.

Ditto all as per Serial Item No 110 , but treating small articles such as stop, covers, gully gratings, holdfasts, ends of posts, backs of chowkats, etc, area not exceeding 0.1 sq m each complete all as specified and directed.

Material & Labour for providing cement concrete type B1 1:2:4 (20mm graded aggregate) as in coping,bed plates of hold fast rounded or chamfered on edges, curb including all formwork etc complete all as specified and directed.

Supply & Fix aluminium powder coated sliding window/doors and glass window consisting of stranded section for frames including necessary handles, roller wheels, hinges rubber beading etc, complete all as specified and directed.

Supply & Fix aluminium powder coated window and ventilator shutters, fixed type/ side hung type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws etc, complete all as specified and directed. complete all as specified and directed.

Supply & Fix powder coated aluminium grill of make DG 104 (10mm thick) with DL 102 frame complete all as specified and directed.

Supply & Fix 4mm thick sheet glass, ordinary quality, and glazing with oil putty/wooden beads in squares not exceeding 0.5 Sqm each complete all as specified and directed.

Supply & Fix 4mm thick figured glass, pin head type and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed.

Supply & Fix in repair Wash basins of size 580x450mm, Vitreous China flat back or angle back type, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified and directed.

Supply & Fix in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

Supply & Fix in repair Vitreous China squatting pan of pattern “long pan”, of size 580 mm white with ‘P’ or ‘S” trap, front or back inlet and foot rests, any pattern but excluding flushing cistern and flush pipe complete all as specified and directed.

Supply & Fix in repairs, PVC valve less,10 litre capacity, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

Supply & Fix Chromium plated fancy type 15mm bib tap complete all as specified and directed.

Supply & Fix 15mm bore Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

Supply & Fix 32 mm dia Flush pipe of polyethylene of low or high density or PVC, for low level cistern complete all as specified and directed.

Supply & Fix PVC connection 15mm with PTMT nuts of length 450mm long complete all as specified and directed.

Supply & Fix 15mm dia chromium plated fancy type pillar cock complete all as specified and directed.

Supply & Fix fancy type CP angle Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

Taking down GI tubing 15mm all as directed by EIC

Taking down GI tubing 20mm all as directed by EIC

Supply and laying of CPVC pipes 20mm outer diameter, SDR 13.5 & Plain CPVC SDR 11 fittings on walls/ ceiling or laying in floors complete all as specified.

Supply and laying of CPVC pipes 25mm outer diameter, SDR 13.5 & Plain CPVC SDR 11 fittings on walls/ ceiling or laying in floors complete all as specified.

Supply & Fix 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

Supply & Fix 75mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

Dismantling of PVC water tank exceeding 250 litres and not exeeding 500 Litres capacity complete all as specified and directed.

Supply & Fix 500 Litres Rotational molded polyethylene water storage tank cylindrical, vertical with closed top hoisted and fixed in position complete all as specified and directed.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing, etc. measured separately) complete all as specified and directed.

Supply & Fix 25mm bore ball brass valve high pressure with polythene float with fly nut complete screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

Supply & Fix 100mm dia of PTMT grating doom complete all as specified and directed.

Supply & Fix 32mm dia waste fittings brass chromium plated in wash basin complete all as specified and directed.

Supply & Fix 40mm dia waste fittings brass chromium plated in kitchen sink complete all as specified and directed.

Supply & Fix waste pipe for wash basin of size 32mm dia complete all as specified and directed.

Supply & Fix waste pipe for kitchen sink of size 40mm dia complete all as specified and directed.

Supply & Fix CP fancy type shower rose of size 125mm connected to 15mm bore pipe complete all as specified and directed.

Supply & Fix sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

Supply & Fix CP Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

Material & Labour for providing and injecting chemical emulsion for Post Constructional Anti termite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per Sqm of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and roding etc, complete all as specified and directed.

Supply & Fix harrison rails, anodised aluminium alloy with fixing brackets, stop, roller etc complete all as specified and directed.

Supply & Fix tubular towel rail brass type 20mm dia, D type, 60CM long between flanges complete all as specified and directed.

Material and labour for One light point controlled by one switch with PVC single core unsheathed copper conductor multistranded cables FRLS 1.5 sqmm size drawn through and including PVC conduit of suitable size concealed and all accessories, fire resistant, ISI Marked including 2 mm thick 60mm depth GI sheet pressed modular terminal box (recessed) with top cover including PVC single core unsheathed copper conductor multistranded cables FRLS 1.5 sqmm as earth continuity conductor and making good the disturbed surfaces of walls/floors/ceiling etc all as specified and directed.

Ditto as per item No 150 but for One ceiling fan point controlled by one switch.

Ditto as per item No 150 but for One exhaust fan point controlled by one switch.

Ditto as per item No 150 but for One 3 pin 5 Amps socket outlet controlled by one switch on independent board.

Ditto as per item No 150 but for One 3 pin 5 Amps socket outlet controlled by one switch in the same board with other switches.

Ditto as per item No 150 but for One bell/buzzer point controlled by one bell push in the same board with other switches or independent.

All as per item No. 150 above but with 2.5 Sqmm cable for for one 3/5 pin socket outlet 16 Amps on the independent board.

Supply and fix Modular switch 1 way 6A/10, 1 module complete all as specified and directed.

Supply and fix Modular Bell push 6A 1 module, complete all as specified and directed.

Supply and fix Socket, 6A - 2/3 pin combined 2 module complete all as specified and directed.

Supply and fix Socket 16A - 2/3 pin combined 2 module complete all as specified and directed.

Supply & Fix modular stepped type electronic Fan step regulator, 120W - 2 module complete all as specified and directed.

Supply and fix call bell, AC, 230 Volts, single pole complete all as specified and directed.

Supply & Fix fluorescent LED tube light fitting, 1x20W, 230V,with extruded aluminium housing and high quality PC Diffuser, efficiency of 125 Lumen/watt including LED lamp of 20 Watt complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed.

Supply & Fix fluorescent LED tube light fitting, 1x10W, 230V,with extruded aluminium housing and high quality PC Diffuser, efficiency of 100 Lumen/watt including LED lamp of 10 Watt complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed.

Disconnecting and taking down fans, any size, any make, for servicing /painting and re-hanging / re-fixing in its original position/location for Ceiling Fan 1200mm/1400 mm Sweep including multistranded copper conductor of size 23/0-0076 Sqmm for connection complete all as directed.

Material & Labour for painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc complete all as directed by Engineer In Charge.

Disconnecting, taking down and refixing its original position/location of Exhaust fan up to 380mm sweep after servicing /painting including multistranded copper conductor of size 23/0-0076 Sqmm for connection complete all as specified and directed.

Supply & Fix Thermoplastic polycarbonate IP 65 energy meter enclosure environment friendly, Corrosion proof, chemical resistant weather proof suitable to fix energy meter inside of size 300 x 300 x 170 mm complete all as specified and directed.

Taking down and refixing of electric energy meter single phase including all fixing accessories complete all as specified and directed.

Supply and fix thermoplastic polycarbonate SPN DB, 8 way, 9module, 220 Volts, in accordance with IEC 61439-3 hinged flap type shock proof, Rust free, Corrosion free, acid and chemical resistance, fire retardant, self extinguishing, PE+N terminals, IP 65 Protection including dismantling old one complete all as specified and directed.

Supply and fixing MCB SP 5 to 32 Amps, 240V, 10 KA 'B' curve in the MCB DB complete all as specified and directed.

Supply and fixing MCB SPN 32 Amps, 240V, 10 KA 'C' curve in the MCB DB complete all as specified and directed.

Disconnecting, taking down and refixing its original position/location of Geyser up to 50 litres capacity after servicing /painting complete as specified and directed including multistranded copper conductor of size 2.5 Sqmm for connection complete all as directed.

Material and labour for Earthing with galvanised MS earth plate of size 600 x 600 x 6 mm thick buried directly in ground not less than 2.25 metre below ground level, earth plate paced on all side with charcoal mixed with salt to a thickness of 150 mm in layers, connected by GI earth lead wire of 4 mm thick, soldered and riveted to earth plate. The earthing includes PCC pit chamber, RCC pit cover and frame, watering pipe 20 mm bore, funnel with wire mess with necessary earth work including disposal of surplus soil to a distance not less than 50 metre etc complete all as specified and shown in electrical plate No 3 of SSR Part I - 2009. Note: - Main earthing lead from earth plate to test point & up to 7.5 metre to be provided. The cost for the same shall be deemed to be included in the above quoted rate.

Excavation in trenches in Soft/loose soil not exceeding 1.5 metre wide and not exceeding 1.5metre in depth for foundation, laying of pipes, cables, etc, or for shafts, wells, cesspits, manholes, pier holes, etc, not exceeding 10 Sqm on plan and not exceeding 1.5 m in depth and getting out complete all as specified.

Returning filling in including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick complete all as specified.

Removing surplus excavated soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified.

Supply and spread M Sand for cushioning and covering of UG cables in trenches complete all specified and directed. (Note : For measurement purpose only punned thickness shall be measured and paid)

Supply and laying un-reinforced precast concrete cable cover class LV type-I flat size 250mm x 150mm x 40mm complete all specified and directed.

Supply & laying in replacement Galvanised steel tubing of size 40 mm bore, light grade to be fixed on walls or laid under roads for passing cables complete all as specified and directed.

Supply, laying for replacement of unserviceable underground LT cable 1100 Volts grade heavy duty electric cable XLPE outer sheathing with aluminium conductor, Armoured confirming to IS-7098 Part-I (1988) with latest amendments of size 10 Sqmm x 2 core including taking out old unserviceable cable complete all as specified and directed.

Amount of Credit Schedule shall be deducted to arrive the Contract Sum.

Classic Builders