State Plan Scheme 2020-21-Contiuing Project - Construction of Building for District Police Office, Kannur City-Phase III (DSR 2021)

CIVIL WORKS

2.8.1 Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil.

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources).

50.6.7.1 Laterate masonry with neatly dressed laterate stone of size 40x20x15cm or nearest size in cement mortar 1:6 for foundation and basement including all cost of materials, labour charges etc.

50.6.7.3 Laterate masonry with neatly dressed laterate stone of size 40x20x15 cm or nearest size in cement mortar 1:6 for superstructure above floor two level upto floor five level including all cost of materials, labour charges etc.

13.1.1 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand).

50.10.1 Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

12.50 Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

12.51.1 Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screwscomplete :Ridges plain (500-600 mm).

OD151035/2025-2026 Providing and fixing Square type 160mm UPVC gutter including all cost and conveyance charge etc. complete.

5.9.1 Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.1.2 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size derived from natural sources).

5.22.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more.

5.22A.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more.

5.9.6 Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts.

5.2.2 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

16.68 Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M - 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

13.80 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

13.47.1 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm).

13.48.2 Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.75 ltr/10 sqm of approved brand and manufacture.

13.48.3 Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture.

13.69.1 Polishing on wood work with ready mixed wax polish of approved brand and manufacture:New work.

10.25.2 Item Shifted to Sub head 14 as item 14.73 Item Shifted to head 14 as item 14.74 Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

12.48 Providing & fixing on roof pressed clay tile (Mangalore tile) of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately).

12.49 Providing & laying on roof pressed clay tile ridge (Mangalore tile) of 20 mm thickness and of approved pattern on steel frame work complete (steel frame work to be paid separately ).

OD151036/2025-2026 Supplying, laying and jointing 40mm dia (6KG/CM2) HDPE pipe for water line from bore well pump to surface inside the bore including all fitting charges etc. complete or above dia PVC casing (ISI marked) and labour charges of conveyance to site etc.

OD205255/2025-2026 Preparation of all drawings submitting and arranging inspection from KSEB,obtaining power allocation and permanent power connection etc and commissioning of the whole installation in the premises.

21.1.2.2 For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron).

21.2.1 Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS : 12823 Grade I Type II, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer - in- Charge.Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side.

21.3.2 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50 mm thickness (weight not less than 12.50 kg/sqm).

9.100.1 Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:125 mm.

9.113 Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of approved quality for aluminium door, with necessary screws etc complete as per direction of Engineer- in- charge.

9.84 Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width form 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

9.97.4 Providing and fixing aluminium tower bolts, ISI marked, anodised(anodic coating not less than grade AC 10 as per : 1868), transparent or dyed to required colour or shade, with necessary screws complete: 150x10 mm.

13.45.1 Finishing walls with textured exterior pint of required shade:New work (Two or more coats applied @ 3.28 ltr/ 10 sqm ) over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm.

INTERIOR DESIGN WORKS

OD205257/2025-2026 Supply of shock treatment chart duly framed and placed in a conspicuous location for clear vision.

OD193659/2025-2026 Supply and Installation of Indian Map made with 12mm Marine Plywood (BWP 710 Grade) and One side 0.7mm inner laminate and other side 1mm laminate finish including cost and conveyance of materials, labour charges, all accessories and fittings etc. complete as per the directions of Engineer in charge.

OD193662/2025-2026 Supply and Installation of TV Unit made with 16mm Marine Plywood (BWP 710 Grade) and One side 0.7mm inner laminate and other side 1mm laminate finish including cost and conveyance of materials, labour charges, all accessories and fittings etc. complete as per the directions of Engineer in Charge.

OD193663/2025-2026 Supply and installation of 12mm Marine Plywood (BWP 710 Grade) and inside 0.8mm Laminate and Visible area 1mm PVC Laminate Finish, including cost and conveyance of materials, labour charges, all accessories and fittings etc. complete as per the directions of Engineer in Charge.

OD193658/2025-2026 Supply and Installation of Wall panel made with 12mm Marine Plywood (BWP 710 Grade) and One side 0.7mm Inner laminate and other side Veneer Finish including cost and conveyance of materials, labour charges, all accessories and fittings etc. complete as per the directions of Engineer in Charge.

OD193660/2025-2026 Supply and installation of 12mm marine Plywood (BWP 710 Grade) and inside 0.8mm Laminate and Visible area 1mm PVC Wooden Laminate Finish including cost and conveyance of materials, labour charges, all accessories and fittings etc. complete as per the directions of Engineer in Charge.

OD193657/2025-2026 Providing Nylon net Blinds for Windows with all necessary fittings etc. complete as per direction of Engineer in charge.

ELECTRICAL WORKS

21.1.1.2 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitre

1.10.2 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq mm FRLS PVC insulated copper conductor single core cable etc as required.Group B.

1.10.3 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C.

1.17.12 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 2.5 sq. mm

1.17.21 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 4 sq. mm

1.17.3 Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 X 1.5 sq.mm

1.21.1 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm.

1.21.2 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm.

1.24.1 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch.

1.24.2 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.2 way 5/6 amps switch.

1.24.3 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch.

1.24.4 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet.

1.24.5 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet.

1.24.6 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.Telephone socket outlet

1.24.7 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.TV antenna socket outlet.

1.24.8 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.Bell push.

1.25 Supplyi

ng and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

1.26 Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

1.53.1 Supplying and drawn of UTP 4 pair CAT 6 LAN cable in the existing surface/recessed steel/PVC conduit as required1 run of Cable.

1.27.1 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm).

1.27.2 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm)

1.27.4 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.6 Module (200mmX75mm).

1.27.5 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.8 Module (125mmX125mm).

1.28.1 Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.1 or 2 Module.

1.28.2 Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.3 Module.

1.28.3 Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.4 Module.

1.28.4 Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.6 Module.

1.28.5 Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.8 Module.

1.28.6 Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.12 Module.

90.10.1.2 Supply & Fixing the following types/ sizes of boxes suitable for modular accessories in surface/ recess including making good the damages, colour washing etc as required (RoHS compliant )2 module moulded plastic box on surface.

90.10.1.3 Supply & Fixing the following types/ sizes of boxes suitable for modular accessories in surface/ recess including making good the damages, colour washing etc as required (RoHS compliant )3 module moulded plastic box on surface.

90.10.1.4 Supply & Fixing the following types/ sizes of boxes suitable for modular accessories in surface/ recess including making good the damages, colour washing etc as required (RoHS compliant )4 module moulded plastic box on surface.

90.10.1.5 Supply & Fixing the following types/ sizes of boxes suitable for modular accessories in surface/ recess including making good the damages, colour washing etc as required (RoHS compliant )6 module moulded plastic box on surface.

90.10.1.6 Supply & Fixing the following types/ sizes of boxes suitable for modular accessories in surface/ recess including making good the damages, colour washing etc as required (RoHS compliant )8 module moulded plastic box on surface.

90.10.1.7 Supply & Fixing the following types/ sizes of boxes suitable for modular accessories in surface/ recess including making good the damages, colour washing etc as required (RoHS compliant )9 module moulded plastic box on surface.

90.10.1.8 Supply & Fixing the following types/ sizes of boxes suitable for modular accessories in surface/ recess including making good the damages, colour washing etc as required (RoHS compliant )10 module moulded plastic box on surface.

90.10.3.14 Supply and Fixing the following modular switches & accessories in the existing front plates and giving necessary connections as required (RoHS compliant )25A SP switch with indicator

90.10.3.15 Supply and Fixing the following modular switches & accessories in the existing front plates and giving necessary connections as required (RoHS compliant )32A DP switch with indicator.

90.10.3.22 Supply and Fixing the following modular switches & accessories in the existing front plates and giving necessary connections as required (RoHS compliant )6A 3 pin plug top.

90.10.3.23 Supply and Fixing the following modular switches & accessories in the existing front plates and giving necessary connections as required (RoHS compliant )16A 3 pin plug top.

1.32 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

1.33 Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

1.38 Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required.

1.47 Supplying and fixing extra down rod of 10 cm length G.I. pipe, 15 mm dia, heavy gauge including painting etc. as required. (Note: More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored).

1.56 Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess, including providng and fixing 2 Nos. 3 pin 5/6 A modular socket outlets and 2 Nos. 5/6 A modular switches, connection etc. as required. (For light plugs to be used in non residential buildings).

1.58 Supplying and fixing PVC batten/ angle holder including connection etc. as required.

90.4.5.4 Supply, Installation, testing and commissioning of ceiling fan of following sizes including wiring the down rods of standard length (up to 30 cm) with 1.5 sq. mm FRLS PVC insulated, copperconductor, single core cable etc. as required. 1200mm sweep - ceiling fan complete with service value minimum 4.0(cub meter/minute/Watt), Air delivery minimum 210(cubic meter/minute), Copper winding suitable for 230V/240V single phase AC supply.

19.1 Supply, installation, testing and commissioning of 1200 mm sweep BEE-5 star rated ceiling fan with brushless direct current motor (BLDC) , class of insulation B , 3 no:s blades , 30 cm long down rod , 2no:s canopies, shackle kit, safety rope , copper winding, power factor not less than .9, service value (CM/M/W) minimum 6.00, Air delivery minimum 210 cum/min,350 RPM (tolerance as per IS :374-2019, THD less than 10% remote or electronic regulator unit for speed control and all remaining accesories including safety pin, nut and bolts , washers, temperature rise equal to 75 deg celsius ( maximum) , insulation resistance more than 2 Megaohm , suitable for 230V,50 Hz, single phase AC supply , earthing etc., complete as required:

OD151043/2025-2026 Supply installation and commissioning of exhaust fan upto 250mm with self opening loovers in the existing opening.

OD151041/2025-2026 Supply and fixing of CAT6 I/O socket in the existing suitable modular plate and suitable GI box ,giving proper connection as required.

OD151038/2025-2026 Supply, installation, testing and commissioning of Energy Efficient 9W LED Bulb of Philips make or equivalent ,giving connections etc. complete as required.

OD151044/2025-2026 Supply, conveyance, installation, testing and commissioning 400mm sweep wall mounting fan of the following sizes using mounting brackets supplied along with the fan and giving connection with existing wire.

OD151042/2025-2026 Supply, installation, testing and commissioning of 20W LED Tube Light fittings of make Crompton or equivalent, giving connection with 3 core PVC insulated and sheathed round Cu flex on wall/ceiling conforming to relevant ISS etc. complete as required.

90.16.1.10 Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required3.25 mm GI conductor (10 SWG).

90.16.1.11 Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required4.06 mm GI conductor (8 SWG).

90.12.7.42 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacin

g of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 25 sq mm with factory made clamp.

90.12.7.40 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 10 sq mm with factory made clamp.

OD151039/2025-2026 Supply and crimping of RJ 45 connectors.

OD152988/2025-2026 Supply installation and commissioning of profile light including all accessories.

OD152546/2025-2026 Supply installation and commissioning of profile light adaptor.

OD152547/2025-2026 Supply installation and commissioning of strip light including all accessories.

OD152548/2025-2026 Supply installation and commissioning of strip light adaptor.

OD152549/2025-2026 Supply installation and commissioning of 24 U rack with all accessories.

OD152953/2025-2026 Supply and fixing of expansion fan hook on ceiling including all accessories for hanging ceiling fan.

90.12.7.41 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 16 sq mm with factory made clamp.

OD152993/2025-2026 Supply and laying of HDMI cable of length upto 5 meter.

OD153035/2025-2026 Supply, fabricate, handle and erect fabricated 24 swg GSS ducting as per drawing, complete with all fittings such as tee bends, etc. as required.

OD153030/2025-2026 Supply, fabricate, handle and erect fabricated 22 gauge GSS ducting as per drawing, complete with all fittings such as tee bends, etc as required.

OD153053/2025-2026 Supply & fixing of Thermal insulation with 9mm thick closed cell Nitrel Rubber insulation with adhesive as per the recommendation of the manufacture.

OD153050/2025-2026 Supply & fixing of Acoustic insulation with 10mm thick Nitrel Rubber insulation with adhesive as per the recommendation of the manufacture.

OD153054/2025-2026 Canvas connection of fire retardant quality for connecting the indoor unit to ducting including all accessories.

OD153063/2025-2026 Supply installation ,balancing of powder coated ,extruded Aluminum linear grills for air conditioned areas for supply air & return Air .

OD153108/2025-2026 Supply of 5 TR ductable split air cooled Air-conditioners each complete with single scroll compressor , air cooled condenser, GSS casing, filters, cooling coils, fan motors ,refrigerant controls and accessories .

OD153184/2025-2026 Supply of 11 TR ductable split air cooled Air-conditioners each complete with single scroll compressor , air cooled condenser, GSS casing, filters, cooling coils, fan motors ,refrigerant controls and accessories.

OD153787/2025-2026 Supply and installation of 9W Ceiling light sqaure/round of approved brand with 5 year warranty.

OD153788/2025-2026 Supply and installation of 12W Ceiling light sqaure/round of approved brand with 5 year warranty.

OD153789/2025-2026 Supply and installation of 18W Ceiling light sqaure/round of approved brand with 5 year warranty.

OD153790/2025-2026 Supply and installation of 24W Ceiling light sqaure/round of approved brand with 5 year warranty.

OD153791/2025-2026 Supply and installation of one feet mirror of approved brand with 5 year warranty.

OD153839/2025-2026 Supply and fixing of 3 Watts or above UP and Down of approved make with 5 year warranty.

OD153842/2025-2026 Supply, installation, testing and commissioning of following port switch (10/100/1000 Mbps) 24 Port GIGABIT Desktop Switch D-Link / TP-Link approved make, giving connections and configuration etc complete as required.

FIRE FIGHTING WORKS

90.16.1.3 Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required3.15 mm copper conductor ( 10 SWG).

90.16.1.4 Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required4.00 mm copper conductor ( 8 SWG).

OD151591/2025-2026 Supply, Instalation, Testing and Commissioning of Electric driven hydrant pump suitable for automatic operation consist of the following: 1620LPM at 45 MWC ,Electric Motor Driven Horizontal End Suction, Top Discharge, Back Pull Out Design, Centrifugal Main Pump set of Standered fitted construction with Cast Iron casing/impeller directly coupled to suitable HP,2900 RPM, SPDP Motor with class B/ class F insulation both mounted in a common base plate and foundation bolts complete as required. (MAKEKIRLOSKAR-)

OD151590/2025-2026 Supply, Installation, Testing and Commissioning of Electric Driven automatic pressuration pump suitable for automatic operation consist of the following. 10.8m3/hr at 50 MWC, Model KDT 1078 Electrical Motor Driven Horizontal End Suction, Top Discharge,Back Pull out Design Centrifugal Jockey Pump of stantard fitted construction with Cast iron casting and Bronze Impeller directly coupled to 10 HP, 2900RPM squirrel cage, TEFV motor with class B/ Class F insulation both mounted in a common base plate with coupling guard, base plate and foundation bolts complete as required. (MAKE-KIRLOSKAR- )

OD151589/2025-2026 Supply, Instalation, Testing and Commissioning of Electric Driven automatic pressuration pump suitable for automatic operation .Electrical Motor Driven Horizontal End Suction, Top Discharge,Back Pull out Design Centrifugal tress Pump of stantard fitted construction with Cast iron casting and Bronze Impeller directly coupled to 5HP, 2900RPM squirrel cage, TEFV motor with class B/ Class F insulation both mounted in a common base plate with coupling guard, base plate and foundation bolts complete as required. (MAKE-KIRLOSKAR -)

OD151594/2025-2026 Fabricating, Supplying, Erection, Testing and Commissioning of cubical type floor mounted power cum Control panel complete with suitable switch gear Bus bars, Relays, Contactors,Indicating lamps,fuses, Insruments, Automatic Isolators and Auxiliary switch including connections complete as required for 2 no Electrical pump, and 1 no Jockey pump

OD151645/2025-2026 Industrial type pressure switch with isolation cock. (MAKE-INDFOS).

OD151646/2025-2026 Pressure gauge with isolation cock. (MAKE-GURU).

OD151647/2025-2026 Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil). 4 X 16 Sq.mm

OD151648/2025-2026 Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil). 3.5 X35 Sq.mm.

OD151840/2025-2026 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 4 X 16 Sq.mm

OD151845/2025-2026 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 3.5x35 Sq.mm.

OD151651/2025-2026 Providing and fixing of 25 mm dia. Air Release valve. (MAKE-GEM/ATOM).

OD151652/2025-2026 Providing and fixing of Hose Reel drum with 30Mtrs long 19 mm dia. Rubber Hose with 19 mm dia. Nozzle (MAKE-ADDI/NEW AGE).

OD151653/2025-2026 Providing and fixing of External Fire Hose box made out of 16 SWG Mild Steel sheet of size / fiber including supports and accessories. (To accommodate 1 Nos. of 15 Mtrs. Hose and branch pipe. (MAKE-FRIENDS / ANASWARA).

OD151654/2025-2026 Supply, Instalation

, Testing and Commissioning of Heat Detector.(MAKEAGNI/ RAVEL).

OD151655/2025-2026 Supply, Instalation, Testing and Commissioning of Photo Electric Detector.(MAKE-AGNI/RAVEL)

OD151656/2025-2026 Supply, Instalation, Testing and Commissioning of Dual Tone Electronic Hooter.(MAKE-AGNI/RAVEL)

OD151657/2025-2026 Supply, Installation, Testing and Commissioning of Manual call point with Hammer and Chain (MAKE-AGNI/RAVEL)

OD151658/2025-2026 Supply, Instalation, Testing and Commissioning of 6 Zone Main Fire Alarm Control Panel with Built-in Battery Charger and 12 V Ah Lead Acid Battery Complete as required. (MAKE-RAVAL/AGNI)

OD151659/2025-2026 Supply, Installation, of Signages as pe the requirement of site.

OD151689/2025-2026 Supply, Installation, Testing and Commissioning ABC type fire extinguishers 6kg capacity make kanex / safex or equivalent.

OD151705/2025-2026 Supply, Installation, Testing and Commissioning of exit light (Double sided with battery backup) make aimfire/ safe india or equivalent.

OD151789/2025-2026 Supply and laying of 2x1.5 sq.mm PVC insulated sheathed armoured (FRLS) copper fire alarm cable for fire alarm system make polycab/ havells or equivalent.

LIFT WORKS

d and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately): For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron).

H T WORKS

OD151798/2025-2026 Supply, Installation, Testing and Commissioning of power amplifier.

OD151806/2025-2026 Supply, Installation, Testing and Commissioning of wall moulded PA speaker 10W in CRCA sheet fabricated with LMT for Talkback facility having push to talk switch compatiable speaker to play music with precise voice clarity.

OD205695/2025-2026 Supply, Installation, Testing and Commissioning of Dry Chemical Powder (DCP) type extinguisher of 4 Kg capacity with ordinary nozzle on the top of the fire extinguisher for discharge of liquid & shall have CO2 gas cartridge as the expelling agent complete with bracket fixing screws, spanner & one filing, extinguisher should bear ISI mark. (MAKE-SAFETECH / SAFEX).

OD204221/2025-2026 Supply installation testing and commissioning of 315 KVA ,11 KV/0.433KV, Delta star,3 phase,50HZ, Dyn 11 Vector group -AN Cooled, Dry type, copper woundtransformer, Core made of CRGO suitable for Indoor application with offload tape changer with 11KV Incomer VCB.

OD204496/2025-2026 Supply,Installation,testing and commmisioning of RESIN CAST SPOUT 50*10*305-3no,CT 11 KV 10/5A 10VA-0.2S-3 no,PT 3 PH 11 KV -R3- 0.11 V-R3 25VA -0.2-1nos,VT FUSE 11 KV 2 A MVTF 11-3no, PT FUSE CLAMP CU-6nos in the existing HT Panel ,INCLUDING ALL CONNECTION AS REQ.

OD204512/2025-2026 Supply ,Installation, commissioning, and testing of 0.2S Class HT TOD Ner meter in the existing HT Panel including all connections etc as req.

OD204697/2025-2026 Supply, Installation, testing and commissioning of 100KV AR APFC Panel , cubicle type,MADE OUT OF min 2 mm thick CRCA Sheet totaly enclosed, IP42,Free standing ,floor mounting,dust and vermin proof,powdwe coated ,indoor,compartmentalised , suitable for operation on 3 phase and neutral ,415volt 50HZ AC SYSYTEM,Including internal wiring with suitable size wires, hinged type door with neoprene gasket etc ,

5.4 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

5.8 Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc.as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm).

5.14 Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

5.6 Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

5.20 Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.

5.17 Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.

5.19 Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

12.45.1 Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:12.5 mm thick tapered edge gypsum plain board conforming to IS : 2095-Part 1 :2011 (Board with BIS certification marks).

8.1.2 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Above 120 sq. mm and upto 400 sq.mm

8.4.2 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing masonry open duct as required.Above 120 sq. mm and upto 400 sq. mm

10.1.3 Supplying and making indoor cable end jointing with cast resin compound, including lugs and other jointing materials for following size of 3 core, XLPE Aluminium conductor cable of 11KV grade as required:240 sq.mm.

7.1.2 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Above 35 sq. mm and upto 95 sq. mm.

7.1.3 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Above 95 sq. mm and upto 185 sq. mm.

7.1.4 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Above 185 sq. mm and upto 400 sq. mm.

7.6.2 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required.Above 35 sq. mm and upto 95 sq. mm

7.6.3 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1KV grade of following size in the existing masonry open duct as required.Above 95 sq. mm and upto 185 sq. mm.

7.6.4 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required.Above 185 sq. mm and upto 400 sq. mm

9.1.24 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 95 sq. mm (45mm)

9.1.25 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 120 sq. mm (45mm).

9.1.26 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 150 sq. mm (50mm).

9.1.27 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 185 sq. mm (57mm)

90.16.1.3 Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required3.15 mm copper conductor ( 10 SWG).

4.1.2 Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 150 mm width X 50 mm depth X 1.6 mm thickness.

4.2.2 Supplying and installing following size of perforated pre-painted M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts

& nuts, painting suspenders etc as required.150 mm width X 50 mm depth X 1.6 mm thickness.

1.10.2 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit,with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group B.

1.10.3 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit,with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C.

1.14.2 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire.

1.14.3 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 4 sq. mm + 1 X 4 sq. mm earth wire

1.25 Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

1.33 Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.

1.32 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

1.56 Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess, including providng and fixing 2 Nos. 3 pin 5/6 A modular socket outlets and 2 Nos. 5/6 A modular switches, connection etc. as required. (For light plugs to be used in non residential buildings).

2.22 Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

2.21 Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

OD205191/2025-2026 PANEL BOARDS Fabrication, Supply and Installation of dust and vermin proof, wall/floor mounting cubicle construction made from 2 mm CRCA sheet, providing necessary supports made from the same gauge CRCA sheet to fix meters, fuse units, CT, MCCBs etc,hinged door construction for the front side with compartments knock out for cable entry and exit, painting the entire board with 2 coats of synthetic enamel paint over a coat of zinc chromate primer etc as required including fixing it on wall/ floor,making good the damages colour washing etc. as required. Comprising the following: SSB Incomer: 250A, 25kA 4P MCCB Thermal magnetic-1No. Metering and indication lamps RYB Indication, MFM with control fuses, and CTs--1No. Bus bar: Al busbar suitable for 250A. Outgoings:125A,16kA TPN MCCB Thermal magnet-2Nos. 100A,16kA TPN MCCB Thermal Magnetic-1No. 63A,16KA TPN MCCB Thermal Magnetic-5Nos. 160A FP Isolator-1 No.

OD205198/2025-2026 PANEL BOARDS Fabrication, Supply and Installation of dust and vermin proof, wall/floor mounting cubicle construction made from 2 mm CRCA sheet, providing necessary supports made from the same gauge CRCA sheet to fix meters, fuse units, CT, MCCBs etc,hinged door construction for the front side with compartments knock out for cable entry and exit, painting the entire board with 2 coats of synthetic enamel paint over a coat of zinc chromate primer etc as required including fixing it on wall/ floor,making good the damages colour washing etc. as required.Comprising the following: MSBIncomer:250A FP MCCB 25kA-1 No. Meters and indication lamps: RYB Indication, MFM with control fuses and CTs. Busbar: 32X10 mm Al busbar for 3 Phases,32X6 mm busbar for neutral and 25X3 mm Cu busbar for earthing. Outgoing: 100A TPN MCCB 16KA-1 No. 63A TPN MCCB 16KA-5Nos 40A TPN MCCB 16KA-1 No. 160A TPN Isolator-1 No

OD205202/2025-2026 PANEL BOARDS Fabrication, Supply and Installation of dust and vermin proof, wall/floor mounting cubicle construction made from 2 mm CRCA sheet, providing necessary supports made from the same gauge CRCA sheet to fix meters, fuse units, CT, MCCBs etc,hinged door construction for the front side with compartments knock out for cable entry and exit, painting the entire board with 2 coats of synthetic enamel paint over a coat of zinc chromate primer etc as required including fixing it on wall/ floor,making good the damages colour washing etc. as required. Comprising the following: LIFT PANEL Incomer:40A FP Isolator-1 No. Meter and indication lamps: RYB indication, MFM with control fuses and CTs. Busbar;25x6 mm Al busbar for 3 phases,26x6mm Al busbar for neutral and 25x3 mm Cu bus bar for earthing. Outgoing:32A FP RCBO 100mA-1No. 25A DP RCBO 30mA-1No. 6A SP MCB 10KA-2Nos.

10.5.3 Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :240 sq. mm

10.4.3 Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core,XLPE aluminium conductor cable of 11 KV grade as required:240 sq. mm

OD205249/2025-2026 Supplying and making cable route marker with cement concrete 1:2:4(1 cement:2 coarse sand:4 graded stone aggregate 20mm nominal size) of size 60cmx60cm at the bottom and 50cm x50cm at the top with a thickness of 10cm including inscription duly engraved as required.

OD205250/2025-2026 Supply, installation, testing and commissioning of 30 KVA,3 phase INPUT and 3 phase OUTPUT online double conversion IGBT UPS with 20 Nos 100Ah Sealed maintenance free (SMF) batteries with 15min back up, battery rack and interconnections cable for battery etc as required.

OD205254/2025-2026 Preparation of all drawings, submitting and getting approval from Electrical Inspectorate, submitting of completion certificates and arranging inspection, getting sanction and energization certificates from Electrical Inspectorate and commissioning of the whole Installation in the premises. All statutory payments will be reimbursed on production of the original receipts.