Repairs to Building No 435 with Structural Strengthening inside factory at AFK

Amount

Submitting detailed structural design and drawings from authorised designer for necessary column, beam and footing for strengthening of the existing structure.

Taking down shutters of any description not exc. 1 sqm each and removing to CW store

Taking down existing chowkats or frames with shutters (without taking off shutters from the frame) any type exc. 1.5 sq.mt. but not exc. 4 sqm. each and removing to CW store.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including quoins, arches, pillars etc but excluding ashlar dressed stonework and precast concrete article.

Dismantling structural steel work including doors/ gate/ windows but excluding framed truss etc.

Taking down cement plaster on brick or stone walls etc. including raking out joints, hacking for key , scrubbing down with water etc. to receive plaster etc. complete.

Demolition of cement concrete (reinforced in roofs, beams, staircases, landing, chajjas and similar suspended work (reinforcement cut as required to facilitate demolition).

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness/ roof.

Exacation in trenches n. exe 1.5m wide and n. exc 1.5 in depth; for foundation etc . exc or for manholes etc n. exc 10 sqm on plan and n. exe 1.5m depth and getting out in :- Hard/ Dense soil.

Exacation in trenches n. exe 1.5m wide and n. exe 1.5 in depth; for foundation etc . exe or for manholes etc n. exc 10 sqm on plan and n. exe 1.5m depth and getting out in :- Soft/ Disintegrated rock.

Exacation in trenches n. exe 1.5m wide and n. exe 1.5 in depth; for foundation etc . exe or for manholes etc n. exc 10 sqm on plan and n. exe 1.5m depth and getting out in :- Hard rock.

M&L for providing cement concrete type B 1:2:4mix (20mm graded aggregate ) in foundations, filling and mass concrete fair finished with necessary centering.

M&L providing precast cement concrete type C1, 1:3:6 (20mm graded aggregate) in block masonry with solid blocks, exc 10cm width and setting in cement mortar 1:6, complete

M&L for providing Reinforced Cement Concrete M-30 grade (Design mix) (20mm graded aggregate) in Foundation, including rafts, footing, foundation beams, plinth beams; bases for columns, etc basement slabs, under reamed piles and mass concrete etc complete.

M&L for providing Reinforced Cement Concrete M-30 grade (Design mix) (20mm graded aggregate) in Columns,Pillars,piers,posts and struts etc.

M&L for providing Reinforced Cement Concrete M-30 grade (Design mix) (20mm graded aggregate) in beams,cantilevers,lintels over 1.5m span.

M&L for providing Reinforced Cement Concrete M-15 grade (Nominal mix) 1:2:4 mix (20mm graded aggregate) in chajjas.

M&L for providing formwork to sides of concrete foundations, footings, bases of columns, rafts and raft beams, sides and soffits (if any) of foundation and plinth beams and similar works, vertical or to batter rough finished surface of concrete flat.

M&L for providing formwork to sides of square, rectangular, circular or polygonal pillars, posts, struts, piers, columns and stanctions for rough finished surface of concrete flat.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunch ings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc

M&L for deformed or twisted bars 10mm Dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

M&L for deformed or twisted bars 6 to 8mm Dia, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

M&L for applying of high strength epoxy bonding agent on old concrete surface as directed. Make: Nitobond/ Dr. fixit/Roff.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces on ceiling in CM 1:4 including finishing neeru finish to plastering as specified.

M&L for rendering 20mm thick on fair faces of brick work or concrete surfaces of walls in CM 1:4 including neeru finish to plastering as specified.

S&F of wire netting of galvanised steel wire 0.40mm dia mesh size 20mm fixed with tinned tacks of wire staples.

Cutting holes into or through brick walls/ stone walls built in cement mortar and making good in cement mortar or cement concrete 1:2:4 Type B-1 as required for superficial area of hole exceeding 150 sq cm but n Exc. 400 sq cm.

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, bore of pipe 110mm.

Cutting and uprooting/ plants of tree/plants/bushes/shrubs growing overwall, roof and slab of any position and any location in the building including cutting of brick work or concrete in position not exc. 1 sqm in area up to full depth of roof.

Stripping out/ taking down existing water proofing treatment with plaster from roof slab and parapet walls and stone slab etc. including hacking for key, raking out joints and scrubbing down with water etc to receive plaster as per direction of Engg-in-Charge.

M&L for providing WPT by using membrane over roof & vertical surface, consisting of applying oil bonded bituminous primer coat at 0.30 kg/m2 on a clean & dry surface & then providing a layer of APP modified membrane 3mm thick weighing approx. 4 kg /m2 with non woven polyester reinforcement with very thin polyethylene film on both side with thermofusion process by gas regulated torch & finally applying one coat of super silver sheld aluminium based bituminous paint all as per specification & as directed by E-in-C. Make: Tiki, IWL or equivalent.

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces of walls/column/ roofs/papapet/drains in CM 1:4 including finishing the plastered surface even and smooth without using extra cement.

Supply for liquid waterproofing compound for mixing in cement concrete/ mortar as specified and directed.

S&F framed worked such as grills, gratings etc with ends of bars shouldered and/or rivetted, or forged into spikes, framed guard bars, barred iron doors, ladders; framed balusters; walk ways; railings; frameworks of water tanks and similar work conforming to be Fe 290. Gde-E-165.

S&F Mild steel of grade Fe-410-W for framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc, complete, drilled for fixing of steel sheeting or other covering, doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing complete.

S&F Flush shutters 30mm thick & more, solid core construction, with block board core and plywood face panels, commercial type on both sides

S&F for mild steel butt hinges, medium weight, cold rolled. Size of hinges 100mm.

S&F of mild steel pressed handles , oval type, stove enamelled black. Size of handle 125mm.

S&F mild steel barrel tower bolts stove enamelled balck, with bright bolt, length of bolt 150mm.

S&F mild steel sliding door bolts, plate type stove enamelled black with with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on blot plate and two on stople plate and fixed: length of bolt 300mm.

S&F Powder coated aluminium sliding windows/ventilators three track (01 gauged and 02 glazed shutters ) including glazed panel shutter of standard section of jindal or equivalent with 4mm thick ordinary plain glasses fixed with rubber linning angles cleat and locking arrangement including pvc ball bearing, including stainless steel wire cloth 0.36 mm nominal dia of wire and average width of apreature 1.40 mm etc, making good to the disturbed surface and match with existing surfaces complete all as specified and directed.

M&L for 3.0mm thick sheet glass, ordinary quality and glazing with oil putty in square n. exc 0.5sqm in each pane.

S&F Steel rolling shutters thickness of lath 1 mm, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type.

M&L for preparing plastered or unplastered new/old surfaces of ceiling and applying two coats of oil emulsion distemper.

M&L for preparing plastered or unplastered new/ old surfaces and applying two coats of oil emulsion distemper on walls over one coat of primer with alkali resistant.

M&L for preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise mentioned over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer.

M&L for preparation of old painted wood and wood based surfaces of any description, not otherwise mentioned over 10cm width or girth and applying two coats of synthetic enamel pain

M&L for preparation of old painted steel or iron surfaces of any description, not otherwise mentioned over 10cm width or girth and applying two coats of synthetic enamel paint.

M&L for preparation of new painted steel or iron surfaces of any description, not otherwise mentioned over 10cm width or girth and applying two coats of synthetic enamel paint.

M&L for preparation of old plastered or unplastered surfaces and finishing walls with two coats of cement paint.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm soft/ hard soil.

Removing surplus excavated soil/rock/PCC/tarfelt and demolished material to a distance exc 500m but n exc 1.5 KM and depositing where directed.

Credit Item- Dismantled Door frames with shutters of any description area exc 1.5 Sqm but not exc 4 Sqm each including iron mongries.

M/S Hrushikesh A. Patil (BID ID -842232)