Loading…
India Infra Updates on WhatsApp
Join the Tenderkart WhatsApp channel for India Tender Updates
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹28.8 LAccepted-AOC | L1 | Accepted-AOC Being L1 and reasonable | |
| 2 | L2₹29.5 L+₹15,238.75 (0.52%)Rejected-AOC | L2 | Rejected-AOC Not being L1 | |
| 3 | L3₹30.5 L+₹1.2 L (3.92%)Rejected-AOC | L3 | Rejected-AOC Not being L1 |
Tender Value
₹35 L
EMD Value
₹70,000
Closing Date
12 Jul 2023, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Garrison Engineer Naval Depot
Garrison Engineer Naval Depot Industrial Estate Post 104 Area Visakhapatnam 530007
COMPREHENSIVE MAINTENENCE WORKS OF INS DEGA AND DEGA VIHAR UNDER AGE BR II OF GE ND VISAKHAPATNAM
2023_MES_603163_1
8275GEND
Open Tender
Civil Works
Item Rate
240 days
VISAKHAPATNAM
Please refer Tender documents.
8 documents required · 8 mandatory
₹500
GE ND VISAKHAPATNAM
₹70,000
2 Feb 2024
14 Jun 2023
17 Jul 2023
14 Jun 2023
12 Jul 2023
28 Jun 2023
Amount
The rates quoted by the tenderer shall deemed to be inclusive for the following provisions in addition to the other conditions specified in the tender documents. No claim whatsoever shall be entertained at a later date on this account:- [i] The repairs shall be done by skilled workmen in the relevant field to the entire satisfaction of Engineer-in-Charge. The contractor shall engage sufficient manpower for the entire period so that progress of work shall not be hampered due to non availability of labour at any time. [ii] The contractor on getting information through Site order / Works diary regarding the nature of repair to be carried out, he shall immediately respond to the same and make all out efforts to carry out the same on priority within 48 hours. In case of any delay in responding / attending the repairs within 48 hours, the GE may at his absolute discretion impose penalty on the contractor at Rs. 100/- per day per each work ordered upto 05(Five) days and Rs. 200/- per day thereafter till completion of the work in case of delay without valid reasons as decided by GE. [iii] Further, the above penalty is applicable even for the multiple locations of work at the same period. It is the responsibility of contractor to make suitable arrangements for attending the repairs simultaneously at all the places. [iv] The decision of the GE as to whether a particular repair has been attended or not on a particular day will be final and binding. The above penalty shall be in addition to the provisions made in clause 50 of IAFW-2249 i.e (Compensation for delay in completion of work). NOTE:- Tenderers/bidders are advised to vist the site and quote their rate accordingly and no claim whatsoever in this regard shall be admissible at any later stage.
Taking up or down 15 mm bore steel tubing and connections, including cleaning for Refixing or removal to store complete all as specified and directed
Taking up or down 20 mm bore steel tubing and connections, including cleaning for Refixing or removal to store complete all as specified and directed
Supply, laying and Testing for 16mm dia CPVC pipe SDR11 and plain CPVC SDR11 brass fittings, (ISI Marked), concealed or fixed complete to wall, ceiling or laid in floors complete all as specified and directed.
Supply and laying for 20mm dia CPVC pipe SDR11 and plain CPVC SDR11 brass fittings, (ISI Marked), concealed or fixed complete to wall, ceiling or laid in floors complete all as specified and directed.
Taking down Chowkats or frames exceeding 1.5 Sqm and not exc 4 sqm each (Without taking off shutters from the frames)complete all as specified and directed.
Taking down Chowkats or frames not exceeding 1.5 Sqm each (Without taking off shutters from the frames) complete all as specified and directed.
Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and directed
Taking down shutters of any description not exc 1 sqm each complete all as specified and directed.
S&F Second class hard wood plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.
S&F Factory made 2nd class hard wood 30mm thick glazed and skeleton shutter open rebated and prepared to receive glass gauge etc divided into square with rebated sash bars any number edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, gauge etc (size of members of shutters as specified in SSR Par –I section 8 Clause 8:24 (b) complete all as specified and directed.
M & L for 2 nd class hard wood factory made 35mm thick plain framed pannelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.
S & F for soild PVC Door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, complete all as specified and directed
S & F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall bw covered with heat moulded plain colour PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and botom rail on either side & as gap insert for tip rail & bottom rails; Panelling of plain colour PVC sheet to be fitted in the MS frame weloded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement. suppling and fixing in the frame at site complete all as specified and directed
S & F powder coated aluminium anodised frame for doors with one or more rebates including joining cleats for fixing with powder coating etccomplete all as specified and directed
S & F powder coated aluminium anodised door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws with powder coating etc complete all as specified and directed
S&F for anodised Aluminum sliding window and ventiletor frame made up 62 mm X29.5 mm X1.5 mm thick aluminium section & shutter made up 38 mm / 20 mm/1.5 mm thick without sash bar aluminium section including all necessary joining cleats,hold fast ,rubber gasket anodised snap beading,anodised alumn fittings,suitable alumn handle and locking arrangment etc complete all as specified and directed
S& F in repairs aluminum frame work for grill, deco grill model DG-104 with 10 mm thick flat matt design making scope and level and fixed in 30 x 12 x 5 mm channel complete and necessary fixing arrangements etc complete all as specified and as directed.
Supply & fixing Sheet glass 4mm thick,ordinary quality and glazing with wooden beads in square not exc 0.5 sqm in each complete all as specified and directed.
M&L 12 mm thick prelaminated particle boards exterior grade prelaminated both sides with decoratative choice lamination fixed in aluminium frame work with screws complete all as specified and directed .
M/L for taking down and refixing the same existing aluminium door shutters for carrying out repairs as required, removing the existing beading and fixing new rubber beading of suitable size with adhesive, overhauling of floor springs including greasing and oiling as required complete all as required and as directed area of each shutter not exceeding 4 Sqm.
S & F in repairs aluminium body door closer hydraucally regulated, designation No. 3 universal type , suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg complete all as specified and directed
M&L for cement concrete 1:3:6 type C-1 using 20 mm graded crushed stone aggregate for fixing hold fast, coping, cills and filling in pressed steel door frames including necessary form work and finishing the surfaces to match with existing, complete all as specified and directed.
S&F mild steel flat iron of size 40x4mm thick as in hold fasts conforming to Fe-290 Gde-E-165 complete all as specified and directed
S&F butt hinges 100 mm long medium weight, cold rolled stainless steel complete all as specified and directed.
S&F butt hinges 75 mm long medium weight, cold rolled stainless steel complete all as specified and directed.
S & F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed.
S & F 100 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed.
S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.
S & F 100 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.
S & F for 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.
S&F 12mm thick toughned glass as in hinged doors, partition automatic doors and similar work including cutting to shape, drilling holes required including all fittings and fixture complete all as specified and directed.
Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.
S & F 3 mm thick Sheet glass, ordinary quality in squares not exceeding 0.5 Sqm in each pane fixed with cut & mitred beads complete all as specified and directed .
Taking down cement motar plaster on brick or stone wall etc, including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed
Demolition of brick work built in cement mortar including all quoins,arches,pillars etc but excluding ashlar facing , dressed stonework and precast concrete articles complete all as specified and directed
M&L for Brick work with fly ash bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6 complete all as specified and as directed.
M&L for brick work with flyash bricks straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed
Rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement complete all as specified and as directed.
M&L for rendering 15 mm thick on fair faces of brick or concrete the surface even and smooth without using extra cement in CM (1:4) Mixed with water proofing compound @ 3% of weight of cement complete all as specified and directed. Note :Water proofing compound shall be measured and paid seperately
Demolition of un-reinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness. (Below or above ground level) complete all as specified and directed
M&L for 75 mm thick Cement concrete type B2, 1:3:6 (using 40 mm graded crushed stone aggregate) as in plinth protection and finishing the concrete surface even and smooth without using extra cement complete all as specified and directed.
M&L for 100mm thick PCC type B2 1:2:4 using (40mm graded crushed stone aggregate) as in sub base of floors and finishing the surface rough for receiving top layer complete all as specified and directed.
S & F in repairs chequered cement concrete tiles 300 x 300 x 22 to 25 mm thick, with grey cement and no pigments, set, jointed and pointed in neat cement slurry in floors over and including 20 mm thick cement screed bed in CM 1:6 complete all as specified and directed.
Rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:3 and even and smooth without using extra cement including mixing of water proofing compound wherever required for floors and sides of wall in sunken floors complete all as specified and directed NOTE: Water proofing compound will be measured separately
Supply only integral water proofing compound ISI marked complete all as specified and directed.
Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) removing rubbish off the site complete all as specified and directed.
S&F Coloured non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0. 11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or Coloured cement to match over and including 15 mm thick screed bed or bedding layers in CM 1:4 complete all as specified and directed.
S&F Coloured non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or Coloured cement to match over and including 15 mm thick screed bed or bedding layers in CM 1:4 complete all as specified and directed.
M&L Glazed ceramic tiles in vertical surface 450x 300x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including Screed bed or bedding layer of cement mortar (1:4) 10 mm thick for laying floor finishes complete all as specified and as directed.
M&L for Virified Ceramic tiles dark shade Double charged 8-10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm and not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and laid over and including 20 mm thick cement screed bed in cm 1:4 complete all as specified and as directed
S&F Coloured non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0. 18 sqm but not exceeding 0.38 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or Coloured cement to match over and including 15 mm thick screed bed or bedding layers in CM 1:6 complete all as specified and as directed.
S&F in repairs white colour rotational moulded polyethylene water storage tanks 3/multi layered ISI Marked (cylinderical, vertical with closed top) of 500 Ltrs capacity hoisted and fixed in position complete all as specified and directed.
S&F in repairs white colour rotational moulded polyethylene water storage tanks 3/multi layered ISI Marked (cylinderical, vertical with closed top) of 1000 Ltrs capacity hoisted and fixed in position complete all as specified and directed.
S&F in repairs 20 mm gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified and directed
S&F in repair 25 mm dia ball valves, PTMT high pressure of epoxy coated Aluminium rod and high density plastic ball (200 gms) , screwed for iron pipes or brass ferrule and fixed complete all as specified and directed.
S&F in repairs Vitreous China wash down water closet pan 580 x 440 mm (Pedestal pattern) EWC white complete incl seat and cover, flush pipe incl all joints complete all as specified and directed.
S & F in repairs Vitreous China Ware Wash hand basin white, flat back, size 550 x 400 mm size (flat back or angle back type) including cutting for and pinning ends of brackets or erecting stand complete all as specified and directed.
S &F in repairs Vitreous china urinals, bowl type flat back size 465 x 355x 265 mm whiten minimum with grating and union for discharge pipe , complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws complete all as specified and directed
Waste coupling of PTMT (half or full threaded Minimum weight 60 gm (half or full threaded) bore of discharge pipe 40 mm complete all as specified and directed
Waste coupling of PTMT (half or full threaded Minimum weight 45 gm (half or full threaded) bore of discharge pipe 32 mm complete all as specified and directed
S & F in repairs 15 mm bore pillar taps, fancy type Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed .
S & F in repairs 15 mm bore chromium plated bib tap fancy type cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.
S & F in repairs 15 mm bore Stop valves, chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.
S&F in repairs PVC 10 litres capacity low level flushing cistern white with inlet ball valve float and braket and 32 mm bore PVC flush pipe complete all as specified and directed.
S&F in repairs 15mm dia PVC connection pipe with PTMT nuts of length 450mm all as directed incl taking down old one complete all as specified and directed.
S&F in repairs grating round 100 mm size of PTMT (min weight 25 grms) complete all as specified and directed.
Taking down eaves gutters & rain water pipes ( any size or pattern) including all fittings , heads, shoes , bends, swan- necks, etc including cleaning or refixing or removal to store ( measured overall as fixed along the centre line over fittings & accessories) complete all as specified and directed .
S&F 110 mm dia PVC (SWR) pipes single socketed in any length , with rubber ring joints fixed in walls complete all as specified and directed.
S&F 110 mm dia bore PVC (SWR) bends complete all as specified and directed .
S&F 110 mm PVC (SWR) junction single(Single T) equal or unequal with access doors complete all as specified and directed.
S&F 110 mm PVC (SWR) vent cowl complete all as specified and directed
M & L for preparation new or prevously untreated surfaces of wood and wood based material of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer by using auto roller or airless sprayer machine complete all as specified and directed
prepration of newly plastered wall surfaces by using vaccume based hand held or long handle sander machine and applying three coats of white wash by using auto roller, complete all as specified and directed
prepration of old decorated wall surfaces by using vaccume based hand held or long handle sander machine and applying one coat of white wash by using auto roller, complete all as specified and directed
prepration of old decorated ceiling surfaces by using vaccume based hand held or long handle sander machine and applying one coat of white wash by using auto roller, complete all as specified and directed
prepration of old decorated wall surfaces by using vaccume based hand held or long handle sander machine and applying one coat of distemper oil emulsion (Oil bound washable distemper) by using auto roller or airless sprayer machine complete all as specified and directed.
M & L for preparing old painted steel surfaces over 10cm width or girth and applying one coats of synthetic enamel paint by using auto roller or airless sprayer machine complete all as specified and directed
M&L for preparation of old painted surfaces of wood and wood based materials of any description, not otherwise described and applying one coats of synthetic enamel paint by using auto roller or airless sprayer machine complete all as specified and directed .
Prepration of old decorated wall surface by using vaccume based hand held or long handle sander machine and cleaning the surfaces by using Jet washer and applying one coat of exterior weather proof (100% acryllic paint) by using auto roller or airless sprayer machine complete all as specified and directed
Preparing new plastered surfaces of walls by using vaccume based hand held or long handle sander machine and cleaning the surfaces by using Jet washer and applying two coats of cement based paint by using auto roller or airless sprayer machine complete all as specified and directed .
Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness, including cover fillets and S&F Anodised aluminium snap grid frame work for false ceiling and Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long and Providing and fixing Gypsum Board 12mm thick in ceiling fixed with screws as per manufacturers instructions complete all as specified and directed.
Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings all as specified and directed
S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour as approved by GE. having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed
S&F Pre- painted galvatume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour as approved by GE. having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed
Removing the existing roof treatment completely and roughening surfaces of old concrete floor or concrete surfaces by picking, sweeping clean and washing down with water to remove dust, etc then Brushing neat cement slurry with 3 Kg of cement per Sqm,then Rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 mixed with WPC @ 3% of weight of cement and finished even and fair without using extra cement then supplying testing and applying APP based polymeric membrane minimum weighing 3.5 kg/sqm and minimum 3mm thick reinforced with polyster non woven fabric (weight not less than 150 gms/sqm) laid on primed surface by forced application including coating the APP membrane surface with water based bituminous primer of blow bitumen of 85/25 at 1.2 Kg/Sqm both at bottom and top of the membrance (Three layers of bitumen primer one on plastered surface and two on APP membrane) and finally finished with one coat of bitumenous aluminium primer at 100 gm per sqm complete all as specified and directed. Notes:- (a)The Roof treatment work shall be carried out through the original manufacturer or his authorized applicator only , Contractor will have to submit all necessary documents like Purchase Vouchers, test Certificates, Authorization letter of manufacturer, etc before payment of RAR. (b) Contractor will have to submit a written guarantee for water proofing treatment for a period of 10 years on a stamp paper of Rs 100 . (c) Contractor will have to deposit a FDR for a Sum equal to 3% of Total Cost of water proofing Treatment before issue of final completion of work failing which the sum shall be deducted from his RARs/Final Bill.
M & L for Anodised aluminium partitions (Area of panel not exc 1.5 Sqm each) with frame made of aluminium section of 63.5x38.1x1.5mm size fixed with and including including necessary joining cleats, glazing clips, ruber neoprene packing, anodised aluminum snap beading screws including providing 12mm thick prelaminated particle board, exterior grade prelaminated both sides with decorative choice lamination fixed to alumnium frame including dismantling old partitions complete all as specified and directed.
M/s Sai Venkata Durga Constructions
M/s.G.KRISHNA RAO
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .