/O Regional research Institute (Ayurveda) at Jaral (Siyog) Pandoh Distt.Mandi HP

Amount

Stone soling/boulder filling dry hand packed in under floor including carriage of materials with in all leads, lifts and other incidentals.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete including carriage of materials with in all leads, lifts and other incidentals.

Provding and laying of boulder apron laid in wire crates with 4mm (four millimetre) dia GI wire conforming to IS: 280 and IS:4826 in 100mmX100mm (one hundred millimetre into one hundred millimetre) mesh (woven digonally including 10per cent extra for laps and joints laid with stone boulders weighing not less than 25kg (twenty five kilogram) each as per drawing and techinical specification clause 1301 including carriage of materials with in all leads, lifts and other incidentals.

Construction of Embankment with approved material obtained from borrow pits with any lift, transporting to site spreading, grading to required slope and compacting to meet requirement of Table 300.1 and 300.2 with any lead as per technical specification Clause 301.5 including carriage of materials with in all leads, lifts and other incidentals.

Providing and laying cement concrete 1 : 6 : 12 (one cement : six sand : twelve graded crushed stone aggregate 40mm (Forty millimetre nominal size) mechanically mixed and vibrated and curing complete excluding cost of form work in foundation and plinth including carriage of materials with in all leads, lifts and other incidentals.

25mm (twenty five millimetre) thick cement concrete flooring 1:2:4 (one cement : two sand : four graded crushed stone aggregate 20mm (twenty millimetre) nominal size) laid in one layer finished with a floating coat neat cement. in all floors including carriage of materials with in all leads, lifts and other incidentals.

Precast concrete block masonry in partition wall 10cm (ten centimetre) thick with solid blocks of approved size including quoin blocks, jamb blocks, closer etc. made of cement concrete 1:3:6 (one cement : three sand : six graded stone aggregate 40mm (forty millimetre) and down gauge in cement mortar 1:6 (one cement : six sand) in all floors including carriage of materials with in all leads, lifts and other incidentals.

Precast concrete block masonry (including quoin blocks, jamb blocks, closer etc.) with solid concrete blocks of approved size made of cement concrete 1:3:6 (one cement : three sand : six graded stone aggregate 40mm) and down gauge in cement mortar 1:6 (one cement : six sand) in foundation plinth upto floor all level as per direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Stone work on plain Ashlar punched (ordinary work) in superstructure upto floor all level including pointing with cement mortar 1:6 (one cement : six sand) including pointing with cement mortar 1:2 (one cement :two sand) including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing door frame single rebate fabricated from sections roll formed out of 1.2mm (one point two millimetre) thick galvanized steel (Base steel as per IS 513) with zinc of 120gms/sq.mtr. (one hundred twenty grams per square metre). The overall size of the section should be 80x50mm & 105x60mm (eighty into fifty millimetre & one hundred five into sixty millimetre) with rebate of 37mm (thirty seven millimetre) for shutter. The frame section should be cut to length and meter joined with corner brackets made of CRCA electroplated. The frame should be provided with (a) 3 (three) Nos. of M.S powder coated 4" Butt hinges of 2mm (two millimetre) thickness welded to the frame. (b) 6 (six) Nos of 1.2 mm (one point two millimetre) thick CRCA electroplated stiffeners should be welded to frame. (c) 6 (six) Nos of 8" M.S hold fasts with split end tail welded to stiffener plates. (d) On no. altrop receiver. (e) Each frame should be provided with 25x50mm (twenty five into fifty millimetre) tie rod at bottom. All welded places should be treated with protective coat of zinc rich primer. The entire frame should be provided with a coat of etched primer including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing double rebate door frame fabricated from sections roll formed out of 1.2mm (one point two millimetre) thick galvanized steel (Base steel as per IS 513) with zinc of 120 gms/sq.mtr. (one hundred twenty grams per square metre). The overall size of the section should be 125x60mm (one hundred twenty five into sixty millimetre). The frame section should be cut to length and meter joined with corner brackets made of CRCA electroplated. The frame should be provided with (a) 3 (three) Nos M.S. powder coated 4: butt hinges of 2mm (two millimetre) thickness welded to the main frame. (B) 6 (six) Nos of 1.2mm (one point two millimetre) thick CRCA electroplated stiffeners should be welded to framed. (C) 6 (six) Nos 8" M.S. hold fasts with split end tail welded to stiffener plates (d) one No. aldrop receiver. (e) Each framed should be provided with 25x50mm (twenty five into fifty millimetre) tie rod at bottom. All welded places should be treated with protective coat of zinc rich primer. The entire frame should be provided with a coat of atched primer including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing Eco 5000 (five thousand) series windows fabricated from roll formed sections made of galvanized steel colour coated/powder coated (Base steel as per IS 513 "D" quality, Galvanized as per IS 277 with Zinc of 120 grams/sq.mtr.) (one hundred twenty grams per square metre) with total coated thickness of 0.60mm (zero point six zero millimetre). Coated sections should be with primer coat of Epoxy primer of 5-7 (five-seven) microns thick, finish painted with polyester paint of 12-16 (twelve –sixteen) microns thick and back coated with Alkyd backer of 5-7 five-seven) microns or powder coated with pure polyester powder up to 50-60 (fifty – sixty) microns thick. Section for frame should be of 98 x50mm (ninety eight into fifty millimetre), section for mullion should be of 46x70mm (forty six into seventy millimetre), section for shutter frame should be of 46x46mm (forty six into forty six millimetre), section for fixed glass bead should be of 18 x 25mm (eighteen into twenty five millimetre) and section for fly mesh shutter frame should be of 20x40mm (twenty into forty millimetre). Frame and mesh shutter section should be cut to length and metre joined with corner bracket made of polypropylene. Glass shutter should be metre joined with corner brackets made of CRCA electroplated. Mullion section should be jointed with frame/mullion using Nylon Mullion cap ethyl propylene diamine monomer (EPDM) gasket should be used all around glass in shutter between frame and glazed shutter and both sides of fixed glass. Rubber gasket should be used around fly mesh to fix mesh in mesh shutter. Each glazed shutters should be provided with MS Powder coated friction hings-one set, high grade aluminum Powder coated handles -1 NO. Each mesh shutters should be provided with S.S. Pivot hings-1 set, Seccolor make Handle shall be provided per shutter, window frame should be fixed to brick/concrete masonry by using nylon self expanding caps and driving MS electroplated 80mm (eighteen millimetre) long screws into the caps through frames including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing Gass shutter & Fixed glass portions should be provided with a glass of 4mm (four millimetre) plain float glass including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing stainless steel 32 (thirty two) gauge fly mesh of 304 (three hundred four) grades with 144 (one hundred forty four) holes per square inch. including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing Grill windows should be provided with grill made of 10mm (ten millimetre) Square MS bars welded to at 150mm (one hundred fifty millimetre) center-to-center 6mmx12mm (six millimetre into twelve millimetre) MS flat.Total grill unitshould be powder coated and fixed to window frame with screws. including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 35mm (thity five millimetre) thick including black enamelled M.S. butt hinges flush door shutters including black enamelled M.S. butt hinges interior grade, commercial type, core of black board construction with frame of first class hard wood and wall matched commercial ply veneering with vertical grains of cross bands and face veneers on both faces of shutters including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 40mm (Forty millimetre) thick second class deodar wood wire gauge shutters using galvanized M.S. wire gauge of I.S. gauge designation 85G with wire of dia 0.56 mm (zero point five six millimetre) for doors, windows, clerestory windows including bright finished/black enamelled iron butt hinges with necessary screws including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 250x16mm (Two hundred fifty into sixteen millimetre) anodized aluminum sliding door bolts anodized colour and shade with bolts and nuts screws etc complete including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 250x10mm (two hundred fifty millimetre into ten millimetre)anodized aluminium tower bolts (Barrel type) anodized transparent or dyed to required shade colour and with screws etc. complete including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 125mm (one hundred twenty five millimetre). aluminum handles anodized transparent or dyed to required colour and shade with necessary screws etc. including carriage of materials with in all leads, lifts and other incidentals complete in all respect.

Providing and fixing 100mm (hundred millimetre) bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete including carriage of materials with in all leads, lifts and other incidentals.

Supplying and fixing rolling shutter of approved make made of 80mmX1.25mm (eighty millimetre into one point two five millimetre) M.S. laths interlocked together through their entire length and joined together at the end by end locks mounted on specially designed pipe shaft, with brackets side guides and arrangements for insides and outside locking with push pull operation complete but excluding the cost of the top cover and spring. Shutter having any width including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 27.5 (Twenty seven point five) centimetre long wire spring grade No. 2 for rolling shutters including carriage of materials with in all leads , lifts and other incidentals.

Providing and fixing top cover for rolling shutters having any width including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing ball bearing for rolling shutters including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 1 mm (one millimetre) thick M.S sheet garrage door with frame of 40 mmX 40mm X6mm (forty millimetre into forty millimetre into six millimetre) angle iron 3.15 mm (three point one five millimetre) m.s gusset plates at the junctions and corners,all necessary fittings complete including applying a priming coat of red lead paint. Using Flats 30 mm X 6 mm (thirty millimetre into six millimetre) for diagonal braces and central cross pieces as per direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals as per specification.

Providing and laying spartic ceramic tiles 5.5mm (Five point five millimetre) thick in skirting flooring 300x300mm (Three hundred into three hundred millimetre) size riser of steps laid on a bed of 12mm (Twelve millimetre) thick cement mortar 1:3 (one cement : three sand) finished with flush pointing in white cement as per direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals as per specification.

White glazed tiles 6mm (Six millimetre) thick in skirting risers of steps and dado on 12mm (twelve millimetre) thick cement mortar 1:3 (one cement : three sand) and jointed with cement slurry including carriage of materials with in all leads, lifts and other incidentals.

6mm (six millimetre) cement plaster to ceiling in cement mortar 1:3 (one cement : three sand) complete upto all floor level as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

15mm (fifteen millimetre) cement plaster in single coat on the fair side of brick/concrete /stone walls for interior plastering upto floor all level including arises, internal rounded angles, chamfers and /or rounded angles not exceeding 80mm (Eighty millimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement : six sand) complete as per direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

15mm (fifteen millimetre) cement plaster in single coat on the rough side of brick/concrete /stone walls for interior plastering upto floor all level including arises, internal rounded angles, chamfers and /or rounded angles not exceeding 80mm (Eighty millimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement : six sand) including carriage of materials with in all leads, lifts and other incidentals.

White washing with lime on undecorated ceiling surfaces two coats to give an even shade including thoroughly brooming the surface to remove all dirt dust mortar dirt and other foreign matter including carriage of materials with in all leads, lifts and other incidentals.

Finishing wall with water proofing cement paint of approved brand and manufacture of snowcem/apox of required shade on undecorated wall surfaces (two coats) to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials including carriage of materials with in all leads, lifts and other incidentals.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt,dust and other foreign matter etc. including sand paper smooth complete including carriage of materials with in all leads, lifts and other incidentals.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter sand papering and knotting ready mixed paint with wood priming pink of approved brand and manufacture (Nerolac/ Asian shalimar) conforming to IS: 3536-1966 brushing including carriage of materials with in all leads, lifts and other incidentals.

Painting two coats (excluding priming coat) on new wood and wood based surface with enamel paint to give an even shade including cleaning the surface of all dirt, dust and other foreign matter sand papering and stopping with enamel paint other than white including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing vitreous china wash down water closet (European Type W.C. Pan) with integral 'p' or 's' trap including jointing the trap with soil pipe in cement mortar 1:1 (one cement : one sand) (sheet and cover to be measured and paid for separately) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Orissa Pattern closet CERA or its equivalent.

Providing and fixing vitreous china wash basin with single hole for pillar tap with cast iron or mild steel brackets painted white including cutting holes and making good the same but excluding fitting flat back 550x400mm (five hundred fifty millimetre into four hundred millimetre) including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing vitreous china bowl pattern urinal including connection the urinal with waste pipe by means of white lead mixed with chopped hemp (Waste pipe to be measured and paid for separately) Flat back type of size 430x260x350mm (four hundred thirty into two hundred sixty into three hundred fifty millimetre) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing PTMT Coloured /white automatic flushing cistern with a pair of PVC / C.I. or M.S. bracket complete with fittings including PVC symphonic apparatus, mosquito proof lid, PVC union and coupling for connections with inlet, outlet and over flow pipes including cutting holes and making good the same (overflow pipe to be measured and paid for separately) 10.00 (ten) liters capacity including carriage of materials with in all leads , lifts and other incidentals.

Providing and fixing to wall ceiling and floor galvanized mild steel tube (medium grade) tube fittings and clamps including making good the wall ceiling and floors 15mm (fifteen millimetre) nominal bore including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing in trenches galvanized mild steel tube (medium grade) 20 mm (twanty millimetre) nominal bore including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 32mm (Thirty two millimeter) dia diametre C.P. brass waste for wash basin or sink of approved brand and manufacture including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing C.P. brass angle valve 15mm (Fifteen millimetre) dia without Nuts and pipe including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing C.P. brass bib tap with Capstan head 15mm (Fifteen millimetre) dia including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 15mm (fifteen millimetre) dia C.P. brass stop cock as complete per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing M.I. union for wash basin or sink 32mm (thirty two millimetre) dia size including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 32mm (Thirty two millimetre) dia C.P. bottle trap for wash basin or sink including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 100mm (hundred millimetre) size sand cast iron grating square of approved quality and colour including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 110mm (one hunderd ten millimetre) dia PVC P or S trap for water closet ISI marked including jointing the trap with pan and PVC pipe with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals..

Providing and fixing 110mm (one hunderd ten millimetre) dia PVC plain bends ISI marked including fixing with approved adhesive etc. complete including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 110mm (one hunderd ten millimetre) dia PVC collars ISI marked including fixing with approved adhesive etc. complete as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing 110mm (one hunderd ten millimetre) dia.high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete including carriage of materials with in all lead, lifts and other incidentals as per direction of Engineer-in-Charge.

Providing and fixing G.I./M.I Union of following sizes (where not included in the items) dia including carriage of materials with in all leads, lifts and other incidentals.

15mm (fifteen millimetre)

20 mm (twenty millimetre)

KHEM CHAND