Proposed Construction of New Gymnasium, Library and Physiotherapy Center at TP - 35, FP – 42 (Social Infrastructure Purpose) in Chandlodiya Plot of North West Zone, Ahmedabad Municipal Corporation.

Sr. No. Description Total Amount (In Rs.)

Total Amount Without GST Rs.

I/We am/are willing to carry out work at __________% above / below (should be written in figures and words) the estimated cost

mentioned above. The amount of my/our tender works out as under

Estimated cost put to tender : Rs. 10,14,04,882.72 Estimated cost put to tender : Rs.

Add_____% Above : Rs ___________ Add_____% Below : Rs ___________

In words : Rupees _______________________ In words : Rupees _______________________

The contractor should get the sample of material in respect of quality and source of supply or manufacturer approved by Consultant

/ AMC in all cases. All such approved samples should be kept at site in the custody of EIC-CMC/PMC/AMC. The tests for the

make in external laboratory in presence of CMC/PMC/AMC to be carried out by Contractor at his own cost as per relevant latest

codes. Reinforcement steel & cement original purchase bills shall be produced to CMC/PMC/AMC as and when asked for.

Note-2 Rate includes for any height, any level, any lead & lift and as per directed by EIC.

Note-3 For Fire Fighting System Autoglow Mandatory Sinages and NOC Process and charges of NOC are included.

Signature of Contractor Additional City Engineer

Seal North West Zone

Date Ahmedabad Municipal Corporation

Ahmedabad Municipal Corporation

Proposed Construction of New Gymnasium, Library and Physiotherapy Center at TP - 35, FP – 42 (Social

Infrastructure Purpose) in Chandlodiya Plot of North West Zone, Ahmedabad Municipal Corporation.

Civil, Plumbing & Site Development Work

Sr. No. Item Description Unit Rate Amount

(A) Excavation & Carting

Clearing and grubbing road land including uprooting rank vegetation grass bushes,shrubs,sapling and

1 3,390.00 trees girth up to 300 mm removal of stumps of trees cut earlier and disposal of unserviceable materials. Sqmt 2.81

(C) By mechanical means in area of light jungle.

Excavation for foundation for depth upto 1.5 m including sorting out and stacking of useful materials

2 3,529.00 and disposing off the excavated stuff upto 50 Meter lead. Cum. 148.19

(A) Dense or Hard Soil

Excavation for foundation for depth from 1.5 m to 3.0 m including sorting out and stacking of useful

3 2,004.00 materials and disposing off the excavated stuff upto 50 Meter lead. Cum. 160.77

(B) Dense or Hard Soil

Excavation for foundation for depth from 3.0 m to 5.0 m including sorting out and stacking of useful

4 158.00 materials and disposing off the excavated stuff upto 50 Meter lead. Cum. 172.50

(C) Dense or Hard Soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in

5 3,638.00 layers not exceeding 20 cm. in depth consolidation each deposited layer by ramming and Cum. 129.10

watering etc complete as directed by EIC.

Conveyance charges of earth lime, murrum, building rubbish, manure, garbage, sludge, excavated

rock, fly ash, aggregate of any kind etc. comp. upto any lead. up to 5.0 km

7 772.00 Above 5.0 km & up to 10.00 km Cum. 363.78

Filling in plinth with sand under floors including watering, ramming, consolidating, compacting and

dressing etc. completed.

Filling in foundation and plinth with murrum or selected soil in layers of 20cm. thickness including

watering, ramming and consolidating etc. complete.

Providing and laying rubble soling, 23 cm thick, in a compact manner, foudation, road, footpath etc.

using 200 to 230 mm. cut size stones, covering and levelling the surface with a layer of murrum after

filling the voids with smaller sized stones or stone chips, including watering, ramming well and

consolidating each layer, as directed.

Sr. No. Item Description Unit Rate Amount

P.C.C. && Carting

Providing and laying cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20 mm

11 508.00 nominal size) and curing etc complete excluding cost of form work in Cum. 3,661.30

(A) Foundation and plinth

Providing and laying in position Ready Mixed M250 grade concrete for reinforced cement conctere

work , using cement content as per approved Design Mix manufactured in fully automatic batching

plant and transported to site of work in transit mixer for a lead up to 10 kms having continuous

agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work

including pumping of R.M.C. from transit mixer to site of laying, excluding the cost of centering

shuttering finishing and reinforcement including cost of admixtures in recommended proportions as per

IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and

durability as per direction of the Engineer - in - charge. Without Fly Ash (Min. cement level as per

latest IS 456 shall be maintained) (Cement level 450 kg)

For All Type of R.C.C. Works like Footing, Column, Beam, Slab, Staircase, Walls, Lintel,

Chajja, Shelves, Balconies etc. for Any Shape, Any Height, Any Level, Any Floor, Any Lift and

Providing and laying in position Ready Mixed M-250 grade concrete for reinforced cement concrete

work, using cement content as per approved Design Mix manufactured in fully automatic batching

plant and transported to site of work in transit mixer for a lead up to 10 Kms. having continuous

agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work

including pumping of R.M.C. from transit mixer to site of laying in levels and pattern of bays as detail

of architect and finished with screed board vibrator , vacuum dewatering process and finally finished

13 259.00 by floating, brooming with wire brush etc., finishing and reinforcement including cost of admixtures in Cum. 7,440.00

recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability

without impairing strength and durability as per direction of the Engineer in - charge. Without Fly Ash

(Min cement level as per latest IS 456 shall be maintained)

The rate shall include cost of side shuttering with channels, rails, to form panels and groove cutting etc.

including filling the joint with glass strip/polysulphite complete to use. The rate shall also include the

cost of reinforcement approximate calculated at 5.14 kg/Smt. Rate for all lead & lift & as per directed

by Engineer in - charge. (Note: - Cement content considered in this item is @ 450 kg/cum.)

Providing TMT Bar FE 500D reinforcement for R.C.C. work including bending, binding and placing in

position complete upto floor two level.

Sr. No. Item Description Unit Rate Amount

Centering and shuttering including strutting, steel plates stiffened&by

(A) Excavation steel angles, propping etc. and

removal of form work for any height, any floor, any level, any lead and any lift for:

15.01 983.00 Foundations, footings, bases of columns, etc. for mass concrete. Sqm 171.68

15.02 772.00 Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. Sqm 229.95

Suspended floors, roofs, landings, balconies and access platform. Weather shade, Chajjas, corbels etc.,

including edges

15.04 3,295.00 Lintels, beams, plinth beams, girders, bressumers and cantilevers. Sqm 192.15

15.05 1,239.00 Columns, Pillars, Piers, Abutments, Posts and Struts. Sqm 297.68

15.06 64.00 Stairs, (excluding landings) except spiral-staircases. Sqm 242.55

Drilling hole of required diameter and depth` as directed for fixing of rebars,using hammer drill,

cleaning the hole using mechanical air flower, water etc,providing and fixing rebar in the drilled hole

16 110.00 using RE 500 V4 or Equivalent approved make Cementetious chemical grout and sealant with No. 631.00

necessary scaffolding, staging, labour, tools and equipment etc. complete as directed by Engineer-in-

(A) 8 mm dia bar (160 mm depth)

17 110.00 (B) 10 mm dia bar (200 mm depth) No. 906.00

18 110.00 (C) 12 mm dia bar (240 mm depth) No. 1,261.00

19 110.00 (D) 16 mm dia bar (320 mm depth) No. 2,166.00

20 110.00 (E) 20mm dia bar (400 mm depth) No. 4,212.00

21 110.00 (F) 25mm dia bar (500 mm depth) No. 8,659.00

22 110.00 (G) 32mm dia bar (640 mm depth) No. 15,981.00

(C) Masonry Work

Brick work using common burnt clay building bricks having crushing strength not less than

35kg/Sqcm. In cement mortar 1:6 (1 cement : 6 fine sand) etc. complete as directed by EIC.

(B) Conventional

(i) in foundation & Plinth

24 246.00 (ii) Ground Floor Cum. 4,253.46

25 212.00 (iii) First Floor Cum. 4,293.25

26 98.00 (iv) Second Floor Cum. 4,333.04

27 11.00 (v) Third Floor Cum. 4,372.83

Half brick masonry in common brunt clay building bricks having crushing strength not less than

Kg/Sq.Cm. in Cement mortar 1:4 (1- Cement : 4 -coarse sand ) in

(B) Conventional

(i) Ground floor

Sr. No. Item Description Unit Rate Amount

29 211.00 (ii) First floor (A) Excavation & Carting Sqm 652.64

Providing & fixing 23 cm wide chicken mesh jali with nails & then application of 15 mm plaster on

R.C.C.& masonary joints as per dir. of engg. In charge.

(D) Plaster & Paint Work

Providing 20 mm thick double coat mala cement plaster on Exterior brick / concrete work for

plastering comprising of base coat of 12 mm thick cement plaster in cement mortar (1 Cement :

coarse sand) in rough finishing and 8 mm thick top coat of cement mortar 1:2(1 Cement : 2 Coarse

sand) finished with trovel including scaffolding curing etc. complete.

Providing 15 mm. thick cement plaster in single coat on fair side of brick wall for interior plastering

upto floor two level finished even and smooth in [II] Cement mortar 1:4 (1 cement : 4 fine sand) For all

levels, hights and leads of works. etc. complete as directed by EIC.

33 2,046.00 First Floor Sqm 180.18

34 196.00 Second Floor Sqm 203.34

Ceiling (Min 10 mm thickness)at all hts.

36 1,470.00 First Floor Sqm 139.23

37 83.00 Second Floor Sqm 160.34

Providing 20 mm thick water proof cement plaster using water proofing powder 1Kg/1bag of cement

for all floors on brick / concrete wall work using water proofing materials in C M 1: 4 (1 cement

coasrse sand) including finishing with a flooting coat of neat cement slurry etc complete for all floor.

and shall be guaranteed for minimum period of 10 years after handing over the completed building by

the main contractor to be finished as directed. Stamp paper guarantee 10 years to be furnished before

receiving any payment from the client. etc. complete as directed by EIC.

Providing and applying 2mm thick Texture Plaster of Earthen Textures, Travertino Texture, Coral

texture or equivalent make incorporating fine filaments made of polymer and aggregating natural

stone powder with making grooves on existing base coat of 20 mm thick smooth mala plaster etc.

Complete with two coat Exterior weather proof paint and one coat of primer in any shade As per

drawings and design supplied by architect and instruction given by authority and E.I.C. for all floor all

Providing 8 mm Luxture decorcem expose concerte or brick concerte coating and wall textured paint

using base coat, tapping, durabond expose RCC materials and finishing with decorsil two coat etc.

complete. As per drawings and design supplied by architect and instruction given by authority and

E.I.C. for all floor all height.

Sr. No. Item Description Unit Rate Amount

Wall painting (two coats) with plastic emulsion paint of approved

(A) Excavation brand and manufacture on

41 7,721.00 undecorated wall surface to give an even shade including throughly brushing the surface free from Sqm 78.44

mortar droppings and other foreign matter and sand papered smooth.

Finishing wall with weather proof exterior emulsion paint on wall surface (two coats) to give an

42 2,125.00 required shape even shade after thoroughly brushing the surface to remove all dirt, and remains of Sqm 113.40

loose powdered materials.etc complete including one coat of primer.as directed by EIC.

Applying two coats of acrylic lapy ( putty) & two coats of primer of approved brand and manufacture

43 7,721.00 on new wall surface to give an even shade including thoroughly brushing the surface free from mortar Sqm 40.19

dropping and other foreign matter and sand papered smooth.

(E) Flooring Work

Providing and laying polished Kota stone slab flooring over 20mm (Average) thick base of cement

mortar 1:6 (1cement : 6-coarse sand) or L.M. 1.1.5 (1-Lime putty :1.5 coarse sand) laid over and

44 676.00 jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and Sqm 982.83

polishing etc. complete.

Providing and laying polished kota stone slab 25mm thick in risers of steps, skirting Dedo and pillars

45 28.00 laid on 10mm thick cement mortar 1:3 (1-Cement : 3 coarse sand) and jointed with gray cement slury Sqm 1,176.03

mixed with pigment to match the shade of slab including rubbing and polishing etc. complete.

Providing and laying Ceramic tiles 6mm thick in skrting risers of steps and dedo on 10mm thick

cement plaster 1:3 (1-cement : 3-coarse sand) and jointed with white cement slurry

Providing and laying white glazed tiles 6mm thick in flooring treads of steps and landing laid on a bed

47 55.00 of 12mm thick cement mortar 1:3 (1-cement : 3coarse sand) finishing with flush pointing in white Sqm 908.17

Providing and laying white glazed tiles 6mm thick in skrting risers of steps and dedo on 10mm thick

cement plaster 1:3 (1-cement : 3-coarse sand) and jointed with white cement slurry

Providing and laying Vitrified tiles 8 to 10 mm thick , 24'' x 24'' in flooring treads of steps and landing

49 1,551.00 laid on a bed of 12mm thick cement mortar 1:3 (1-cement : 3coarse sand) finishing with flush pointing Sqm 1,062.50

in white cement.

Providing and laying Vitrified tiles 8 to 10 mm thick , in skrting risers of steps and dedo on 10mm

thick cement plaster 1:3 (1-cement : 3-coarse sand) and jointed with white cement slurry

Sr. No. Item Description Unit Rate Amount

P & L 24" x 24" vitrified 8 mm thick tile flooring

(A) over 20 mm (average)

Excavation base of cement mortar 1:6 (1

cement : 6 coarse sand) on new surface or fixing on existing flooring by adhesive material including

dismentaling of existing flooring and jointed with color cement slurry including finised with flush

pointing & cleaning the surface etc. complete for antiskit

Supply and Installation of High Density Rubber Flooring having thickness of 8.0mm made of 85%

black rubber granules and 15% synthetic EPDM granules. Rich colors, Environmental friendly, non-

52 583.00 toxic, Recycled, non pollution, Moderate and adjusted hardness, Excellent resilience, wear well, Soft, Sqm 3,212.30

anti-slip, anti-fatigue, Density (kg/m3):1000-1200, Hardness (Shore a):68, Stretch (MPA):2.2, Length

(m):10m ±5cm, Width (m):1.0m ±5mm, Thickness: 8mm ±0.3mm

Providing and fixing machine cut, mirror/ eggshell polished , Marble stone work for wall lining

(veneer work) including dado, skirting, risers of steps etc., in required design and pattern wherever

required, stones of different finished surface texture, on 12 mm (average) thick cement mortar 1:3 (1

cement : 3 coarse sand) laid and jointed with white cement slurry @ 3.3 kg/sqm including pointing

with white cement slurry admixed with pigment of matching shade, including rubbing, curing,

polishing etc. all complete as per Architectural drawings, and as directed by the Engineer-in-Charge.

18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore

Providing and laying lift cladding min.10 mm th. machine cut and mirror polished grantite stone for

column / wall cladding by using araldite, stainless steel pins it required including scrapping the surface

and making the surface preparation for cladding. Also include for finishing the joints and exposed

54 158.00 edges shall be polished and finished with white cement slurry admixed with the approved shade Sqm 3,700.00

pigment to match the shade of tiles as per inst. of Architect etc., complete including champhered edges

& V grooves complete as per design. Including cost of 20 mm thick backing coat in C. M. 1 : 4. Rate

includes for all lead & lift & as per directed by EIC.

Providing and fixing 18 mm thick granite gang saw cut, mirror polished, premoulded and prepolished,

machine cut for kitchen platforms, vanity counters, door / window sills , facias and similar locations of

required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1

cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch

ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete

Sr. No. Item Description Unit Rate Amount

Providing and fixing Granite sand which type platform including supplying

(A) Excavation & Carting and fixing granite stone

mm thick mirror polished 1st quality Granite stones in top and side posiition and vertical strip at front

over 25 mm thick polished kotah stone platform fixing in top and sides and itermediates supports

fixing with cement mortar and adhesivee and finishing including providing & cutting of kitchen sink

(as directed) 600 mm x 450 mm x 200 mm size stainless steel sink (as directed by engineer incharge)

at required position etc complete.

Providing & fixing Granite for Door Jamb, Sill and the like similar location of 18mm thick, from

to 2105mm in length and width 150mm /250mm in cement mortar 1:2 [1 white cement : 2 marble dust]

with an admixture of pigment to match the marble shade including fixing with copper pin 7.5cm long

of 6mm diameters in cement mortar 1:2 (1 cement : 2 fine sand) including making rebate for door

shutter in Granite, edege polishing and moulding etc. completed as directed by EIC / Consultant.(Clear

measurement will be taken on sqmt basis for both Jamb)

Providing & Laying 18 mm thick Mirror polish granite For flooring , counter , stair -riser , tread

skirting , dedo, Jambs etc. machine cut or chiselled on bed of cement mortar 1:1 pointing with neat

cement slurry incl. moulding, Making grooves where it is required etc. comp. as per instruction of

engineer in charge.

Sr. No. Item Description Unit Rate Amount

Providing and laying integral cement based water (A) proofing

Excavation & Carting

treatment including preparation of surface

as required for treatment of roofs, balconies, terraces etc consisting of following operations:

(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing

compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including

adjoining walls upto 300 mm height including cleaning the surface before treatment.

(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of

cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS

: 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1

cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved

by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height

including rounding of junctions of walls and slabs.

59 1,195.00 (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of Sqm 944.65

cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-

(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse

sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-

charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing

the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.

(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for

curing and for final test.“All above operations to be done in order and as directed and specified by the

Engineer-in-Charge :

i) With average thickness of 120 mm and minimum thickness at khurra as 65 mm. Rate includes for

all lead & lift & as per directed by EIC.

Providing and laying broken chine mosaic flooring for terrace using 12 mm to 20 mm broken pieces of

glazed tiles to be laid over cement mortar 1:3 to plain or slope and to be tempered to bring mortar

creme out upto surface using white cement including rounding off junctions and extending them upto

15 cm along the wall,clearing with water and oxalic acid etc. as directed.

Providing and laying cement concrete flooring 1:2:4 (1-cement : 2-coarse sand : 4-graded stone

61 11.00 aggregate 20mm nominal size) laid in one layer and finished with a floating coat of neat cement. (B) Sqm 348.08

Providing and fixing M.S. grills of required pattern to wooden frames of windows etc. with M.S. flats

at required spacings and frame alround, square or round bars with round headed bolts and nuts or by

(A) Plain Grill.

Sr. No. Item Description Unit Rate Amount

Structural steel work (Confirming to IS 4923-1997) & Carting

riveted, bolted or welded in builtup for all type

63 1,300.00 sections, inframed work, including cutting, hoisting, fixing in position and applying a priming coat of Kg 126.68

approved steel primer all complete as per the structural designs and directions of Engineer in charge.

Applying priming coat over new steel and other metel surface after and including preparing the surface

64 414.00 by throughly cleaning, oil,grease, dirt and other foreign matter and scoured with brushes fine steel Sqm 34.34

wood, scrapers and sand paper with ready mixed priming paint brushing red lead.

Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint,

65 414.00 brushing, interior to give an even shade including cleaning the surface an even shade including cleanicn Sqm 86.94

the surface of all dirt, dust and other foreign matter

Fabricating, supplying and fixing in position SS railing for staircase and balcony with brush finish and

66 99.00 304 grade as per Indian Standrd and detailed drawing including grinding, cleaning and filling the Rmt. 2,425.00

welded spots with SS finish (Only Length will be paid for payment heigth max.1.0 mt.). The Work to

be executed as per consultant drawing.

Fabricating, supplying and fixing in position SS daso for staircase and balcony with brush finish and

67 46.00 304 grade as per Indian Standrd and detailed drawing including grinding, cleaning and filling the Rmt. 1,365.00

welded spots with SS finish (Only Length will be paid for payment ). The Work to be executed as per

consultant drawing.

(G) Door Window Work

Providing and fixing flush door both sides laminated and I.T.W. beading all around by using I.T.W.

frame 120 mm. x 80 mm. shutter fabricated from 35 mm thick solid core malemine faced three layered

pre laminated flat pressed wood based exterior grade bonded BWP/BWR synthetic resin having

68 80.00 stamped IS 12823 grade I type II including both sides laminates and Stainless steel decorative type Smt 5,773.00

designs fixtures / fastening 2 Nos. Handles, 2Nos. Aldropes, towerbolt, S.S. Hinges etc.including

I.T.W. triangular batten patti of size 30mm x 30mm including three coats of lacquer polishing etc. as

per architectural detailed drawing and as directed by engineer in charge.

Providing and fixing in position collapsible steel shutters with vertical channels 20 x 10 x 2 mm braced

with flat iron diagonals 20 x 5 mm size with top and bottom rails of T_rin 40x 40 x 6 mm with 38mm

dia, steel pulleys complete with bolts, nuts, locking arrangements, stoppers handles including applying

a priming coat of red lead paint.

Sr. No. Item Description Unit Rate Amount

Providing and fixing aluminium extruded section body tubular type

(A) Excavation universal hydraulic door closer

(having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and

door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and

screws etc. complete.

Providing and fixing window having extruded aluminum Colour anodized section frame main outer

size 63.50 x 38.10 x 1.95 mm,@ Wt 1.094 Kg / Rmt, horizontal two track member size 61.85 mm x

31.75 mm x 1.20mm @ wt.of 0.695 Kg/mt, vertical member of size 61.85 mm x 31.75mm x 1.30 mm

@ wt.of 0.659 Kg/mt with sliding shutters of horizontal member size 40mm x 18mm x 1.29mm @

wt.of 0.456Kg/mt, vertical member of size 40mm x 18mm x 1.29mm @ wt.of 0.456Kg/mt, @ Wt.

0.457 Kg/mt with 5 mm thick transparent bronze colour inted float glass with powder coated aluminum

fittings and fixtures and transparent silicon sealant glass fixing to frame as per details etc complete for

Providing and fixing standared extruded of alluminium section of size 63mm x 38.10mm x 1.2mm @

72 9.00 Wt. 0.643 Kg/mt with colour anodized alluminium frame for ventilation with 5 mm thick frosted glass Sqm 1,163.92

as details etc complete for Ventilation

Providing and fixing standared extruded of alluminium section of size 63.50 x 38.10 x 1.95 mm,@ Wt

73 55.00 1.094Kg / Rmt with colour anodized alluminium frame with 5 mm thick transparent bronze colour Sqm 1,509.90

tinted float glass as details etc complete for Fix window.

Providing and fixing All door partly glazed & partly pannelled door of approved colour Andised and

standard extruded alluminium frame 101.60 x 44.45 x 1.60mm @ 1.301 kg. with provided single door

shutters having bottom rail 114.30 x 44.45 x 1.35 @ 1.19 Kg/ Rmt. Lock, Top & style 83.50 x

x 1.80 @ 1.50 kg ,Vartical rail 85.00 x 44.45 x 1.80 @ 1.301 Kg/Rmt and glazing clips 19.00 x

x 0.90 @ 0.124 Kg/Rmt with 5mm thick float glass,silicon gasket and 6mm Pre-lamineted board at

bottom as per drawings 1-nos of pivot/ Hinges 4 nos 125mm, D type 200, Alluminium handle 2 nos,

lock of Apprvoed Quality 1 nos, Towarbolt 150mm 1 Nos, Floor door stopper 1 Nos, including

fixtures & Fastening etc. Complete.

Providing & fixing in position standard extruded Aluminium Partition with Colour anodized hollow

section frame of approved shade & pivoted without shutter fabricated from alluminium standard

section for outer frame size 101.60 x 44.45 x 1.60mm @ 1.301 kg. and using Glasing Clips 19.00 x

75 116.00 17.30 x 0.90 @ 0.124 Kg/Rmt and providing rubber gasket around the glass allover including Sqm 3,063.00

providing 6 mm th. transparent float glass of copper/ gray tint (Structural Glass) fixed with

transparent silicon gasket and in bottom panel 6mm thick compact sheet bothside including all

required materials labours and equipments as per detailed drwg. as directed.

Sr. No. Item Description Unit Rate Amount

Providing and fixing FRP frame size 125x65 mm (A)and 35mm thick&

Excavation FRP shutter with wood grain raised

panneled design finish shutter having extra reinforcement on sides & edges in Gel coat finish. The core

of the shutter & frame is to be filed up with injected polyurethene foam done in situ alongwith

embedded wooden pieces for stiffening & also taking hinges & fintures. The whole FRP frame &

shutter is to be water proof weather proof, termite proof & resistance to mild acid/alkali. Rates are to

be inclusive of S.S hinges with fastener sleeve & alluminium fixtures & fastenings.

(H) Miscellaneous Work

77 1,348.00 Providing throating or plaster drip and moulding to R.C.C. Chhajja. Rmt. 41.25

Providing cement vata (10cm. x 10 cm. size) quarter round in cement mortar 1:1 including neat cement

finishing, watering etc. complete.

Providing and fixing eco-friendly light weight calcium silicate false ceiling tiles having Tegular edge &

15 mm Thick Densified edges on the Tile Periphery for Extra Strength The Light weight calcium

silicate ceiling tiles shall have , light reflection 85% non-combustible as per B.S. 476 part IV, 100%

humidity resistance and also having thermal conductivity0.043° w/m KC.for the best thermal

Insulation . The Light weight calcium Silicate tile shall be of approved texture Fine fissured/

Spintone/Cosmos having NRC value of 0.5 & Globe having NRC value of 0.75 NRC or equivalent of

size 595 X 595 mm to be laid on true horizontal level suspended inter locking metal grid of hot dipped

galvanized steel sections (galvanizing @120 grams per sqm including both side) consisting of main

‘T’ runner suitably spaced at joints to get required length and size of 24X38mm made from 0.30 mm

thick (minimum) sheet, 1200mm centre to centre, and cross ‘T’ of size 24X28mm made out of

0.33mm (Minimum) sheet spaced 1200mm along spaced between main ‘T’ at 600mm centre to centre

to form agrid of 1200X600mm and secondary cross ’T’ of length 600mm and size 24x28mm made of

0.30 mm thick (Minimum) sheet to be interlocked at middle of the 1200X600mm panel to form grid of

size 600X600mm resting on periphery walls/partitions on a perimeter wall angle pre-coated steel of

size (24X24X3000mm made of 0.40mm thick (minimum) sheet with the help of rawl plugs at 450mm

centre to centre with 25mm long dry

Pro. And fixing single layer water proof gypsum board 12.5 mm thick sections using water proof board

of size 1220 mm x 1830 mm x 8.0 mm suspended by GI suspender channel of size 25 mm x 3 mm

with intermediate channel og size 18 mm x 40 mm x 0.8 mm at 1220 mm center to center ceiling

80 465.00 section of size 40 mm x 35 mm x 0.55 mm at 457 mm c/c and perimeter channel A of size 20 mm x 27 Sqm 600.94

mm x 30 mm x 0.5 mm at edges & drops incl.paper tap sand sofit cleat, anchor fastener, scoch bolt

connecting cleat,joining compound top coat on ceiling incl.making necy.opening for light

fitting,diffuser etc. comp. as per detail drawing as directed

Sr. No. Item Description Unit Rate Amount

Providing and fixing Structural Glazing with (A)using

Excavation & Carting

the 17 Micron anodised of approved colour

alluminium section as transium, mullium of size 63mm x 38mm x 2 mm with using 6 mm thick

reflective structural glass of approved make, colour, toughned and shade and fixed with silicone sealant

and spacer tap and at corner sealed neoprene foam dust and Air sealed gasket mirred including

scaffolding, cleaning of glass etc.complete at all heights anf lifts with all necessary fitting and fixtures,

81 60.00 anchore fasteners, necessary M.S. or Aluminium brackets, suitable design for openable or sliding Sqm 3,204.81

window as per Architectural drawing and as directed by Engineer-in-charge. Grooves between the

glasses to be filled with sealant of Dow corning - structural sealant 995, weather sealant 789. The

entire facade should be water proof. The mullions are to be connected to bracket by SS-304 nut bolts.

Measurement shall be given as per actual execution of the work. (Rate are included providing & fixing

of MS structure steel work when and where requried)

Providing and fixing pre-cast Rubber Dye / steel Dye inter locking concrete block 60mm thick with

grade of concrete M300 pnumatic compressed / vibrated mechanically and as per approved design

82 591.00 Confirming to IS 15658 : 2006 including 35 mm Sand layer for levelling and filling the joint with sand Sqm 680.10

in proper line and level as per guidlines of IRC : SP 632018 etc. Complete.(Alcock,Vyara or equivalent

Providing and fixing pre-cast concrete kerb stone of gray cement based concrete block 35cm

length,30cm height and 15cm thick of M250 grade concret as per approved design and including

excavation for fixing in proper line and level,filling the joint with C:M 1:3 (1cement:3fine sand) etc

Providing and fixing "MERINO" Or equivalent BESCO cubicle partion system for toilet by using

following materials, 12mm thick compact laminate with color of HPL Boards, size of cubicle :

1000mm(W) X 1550mm(D) X 2003mm(H), Door size: 1750mm(H) X 610mm(W) including SS "U"

84 37.00 Channel, SS "F" channel, SS top rail, SS coat Hook, SS Privacy thumb turn c/w occupancy indicator, Nos. 41,226.00

SS door knob, SS hinges with cover, SS adjustable foot-316 grade, Rubber lining for groove, SS

Screws 304 G & PVC wall plugs complete as per drawing and design complete.as directed by

Providing and fixing cast iron steps of size 500mm x 150mm x 22.5mm and painting with two coats of

Anti-corrosive paint etc. complete.

86 1,518.00 Sinage - internal and external signage boards in S.tainless steel., wood etc. as per architects details Sq.inch 2.00

Providing and filling with scrap of AAC block (good quality) as a cinder as directed by engineer in

charge in sunks in layers of 15 cm thk including watering placing ramming well etc. as directed.

Sr. No. Item Description Unit Rate Amount

CURTAIN TRACK : (A) Excavation & Carting

Curtain Track G RAIL 4100-(including all accessories) strong functional and fully reversible profile

confirming to HTM66, synthetic wall and ceiling brackets complying with the European NEN

standards, made of aluminium 606035- T6 –F2. Shape and size tolerance in accordance with DIN

17615. White powder coating colour RAL 9010, in accordance with Qualicoat standard. Runner/Glider

hooks made of nylon 6.6 with SS 304 grade hooks. Profile weight must be 394 g/m. The system is

such that if required can be mounted with ANTI-LIGATURE load release components, to provide a

controlled system collapse as per NHS guidelines

CUBICLE / PRIVACY CURTAIN :

Curtains fabric to comply with many safety protocols it must be stain retardant and has a coating of

antimicrobial and fire retardancy effect,must be certified according to international standards , must be

certified by indian govt approved laboratories . it has to contributes to the reduction of transferring

bacteria, help in increasing/improvement of hygienic standards provide greater safety against infection

.No need of sterilization after wash. The antibacterial component facilitate in reducing the growth of

fungi, moulds and mildew that can develop in any type of an indoor environment. Effective after

washes and , Antibaterial activity must be tested accourding to the JIS L 1902:2015 & Antimicrobial

Acitivy must be tested according to AATCC 100-2019 from goverment approved lab. Fire Retadency

test must be done by lab linked to ministry of textile, goverment of India according to NHPA

Blackout Curtains : Providing and installing Elite Series Fabric Roller Blind with BDH make control

unit complete with all hardwares. The Fabric will allow no passage of light and comes with PU coating

which has control over light. The Fabric is made of 100% polyester woven fabric. The thickness is

mm and openness factor is 0% light transmission. Weight of the fabric is 450 grams/ sq. mtr with

tolerance of 10%. . The density of the fabric is 72/in X 30 /in. The fabric comes in variety of shades

and to be finalized as per instruction of Architect in charge. BDH or equivalent makes to be used.

(I) Landscaping Work

Grassing with selection No.1 grass In rows 5 cm apart in both directions including watering and

maintenance of the lawn for 3 months or more till the grass forms a thick lawn, free from weeds and fit

91 183.00 for mowing including supplying farm clay up 300 mm thick, sludge, manure,pesticides , extra earth, Sqmt. 289.84

disposal of rubbish, trench excavation and all labour with lead and lift etc. complete as directed by

Sr. No. Item Description Unit Rate Amount

Providing & Planting of Deep rooted Tree plants required Digging

(A) Excavation of pits 0.6mt. x 0.6mt x 0.6mt,

filling with goodearth with mixing of cow dong and pesticide.planting the following plant of 4' to 6'

92 8.00 height stack it well, maintain it for 3 month name of plants as below etc completed as dircted by Nos. 250.00

Champa Tree (6')

93 8.00 Garmalo Tree (6') Nos. 275.00

94 8.00 Bottel Plam (6') Nos. 600.00

Providing & Planting of Deep rooted exoitic palm trees Digging of pits 0.6mt. x 0.6mt x 0.6mt,

filling with good earth with mixing of cow dong and pesticide.planting the following plant of 8' to 10'

height stack it well, maintain it for 3 month as below etc completed as dircted by E.I.C/PMC.

Ashoka Tree (8')

96 6.00 Gulmohar Tree (8') Nos. 300.00

97 6.00 Kadam Tree (8') Nos. 300.00

98 6.00 Neem Tree (8') Nos. 270.00

99 6.00 Saptapani Tree (8') Nos. 275.00

100 6.00 Golden Bamboo Plam (8') Nos. 150.00

Providing & Planting of Ornamental shurbs Digging of pits 0.6mt. x 0.6mt x 0.6mt, filling with good

earth with mixing of cow dong and pesticide.planting the following plant of 4' to 6' height stack it well,

maintain it for 3 month as below etc completed as dircted by E.I.C/PMC.

Rafic Plant (4')

102 6.00 Red Ixora Plant (4') Nos. 125.00

103 6.00 White Ixora (4') Nos. 125.00

104 6.00 Karan Plant (4') Nos. 60.00

105 6.00 Canna Plant (4') Nos. 12.00

106 6.00 Panama Rose Plant (4') Nos. 75.00

107 6.00 Lily Plant (4') Nos. 12.00

108 6.00 Song of India Plant (4') Nos. 150.00

109 28.00 Providing and supplying fine river silt(Kamp) as directed by EIC Cmt 550.00

Percolation Well

110 88.00 Boring and Sinking 30 cm. Diameter. Percolation well Rmt 760.00

111 2.00 Soak well around 3.0 m. dia. X 5.0 m. liquid depth including brick masonary for well No. 1,30,400.00

112 4.00 Brick masonry collection cum filtration tank around soak well No. 34,500.00

15 cm. diameter strainer pipes (Johnson make) having slot size 1.5 mm x 57 mm (72 slots in one line)

in the casing pipe

Sr. No. Item Description Unit Rate Amount

Supplying, fitting, fixing and lowering 30 cm. (A)diameter strainer&pipe

Excavation 1.2 m long (Johnson make)

having slot size 1.5 mm x 57 mm (72 slots in one line)

115 4.00 Providing and lowering 15 cm size M.S. (3 m long) bail plug to the bore hole. Set 3,800.00

Supplying, lowering, fitting, fixing and joining with Strainer, 15 cm. diameter M.S. Pipe of minimum

5.40 mm wall thickness

117 2.00 Cement ceiling the saline zone as per logging report and as directed by the employer. Job 10,265.00

Supplying, washing and shrouding with approved gravel, the annular gap between the casing pipe and

118 28.00 the remaining annular space to be filled in with puddle clay (for which no measurement with be taken Cumt 1,905.00

and paid for ).

Hire and labour charges for necessary tools and plants for conducting proper tests for percolation

Supplying and fixing reinforced concrete heavy duty nonpressure pipes with collars for culverts

including setting and joining the pipes in C.M. 1:2 watering and laying (To level of slops of I.S. 458 /

1971 Class NP4 of following internal diameter.

(I) 300 mm dia.

Providing & Laying & Jointing glazed stoneware pipes incl. excavation up to 2.0 mt.,refilling,

trasporting the pipe to work site, unloading, lowering in trenches, laying and jointing the pipes in c.m.

1:1 incl. all jointing materials such as cement, sand, hemp, bitumen as dire. testing the pipe line to a

head of 1.5 mt. and hydraulic test as dire incl. watering trenches, spreading ,and carting away of

surplus earth within 100 mt.lead as dire. etc.comp

(A) 230 mm dia.

Providing & laying cement concrete 1:5:10 (1- Cement,5- fine sand,10 - graded stone aggregate

40mm Nominal size ) bedding for stoneware pipes of following internal diameters with necessary

formwork & curing complete.

Providing & laying cement concrete 1:5:10 (1- Cement,5- fine sand,10 - graded stone aggregate

40mm Nominal size ) bedding for stoneware pipes of following internal diameters with necessary

formwork & curing complete.

Sr. No. Item Description Unit Rate Amount

Providing & laying cement concrete 1:5:10 (1-(A) Cement,5- fine sand,10

Excavation - graded stone aggregate 40mm

Nominal size ) bedding for stoneware pipes of following internal diameters with necessary formwork &

curing complete.

Providing, laying and jointing in true line and level 160 diametre U.P.V.C (Type B) conforming to IS

13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to SI

14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with

127 173.00 rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 160 mm diametre x 210 Rmt 822.99

mm length x 196 mm heigh at every 2000 mm center to center or shall be concealed in walls as

directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and

jointed with adhesive solvent cement including cost of all materials.

Providing, laying and jointing in true line and level 110 diametre U.P.V.C (Type B) conforming to IS

13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI

14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with

128 224.00 rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 110 mm diametre x 149 Rmt 826.88

mm length x 145 mm heigh at every 2000 mm center to center or shall be concealed in walls as

directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and

jointed with adhesive solvent cement including cost of all materials.

Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with bricks

having crushing strength not less than 35Kg/Cm2 in C.M. 1:5 C.I. cover with frame (Light duty)

455mm x 610mm intenal dimensions total weight of cover with frame to be not less than 38Kg. (Wt.

129 14.00 of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1 cement :2coarse sand :4- Each 2,903.89

graded stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement

mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete.

(I) Inside dimensions 455mmx 610mm and 450mm deep for single pipe line.

Sr. No. Item Description Unit Rate Amount

Constructing Manhole with R.C.C. top slab in (A)1:2:4

Excavation & Carting

mix (1cement :2-coarse sand : 4-graded stone

aggregate 20mm nominal size) foundation concrete 1:3:6 mix (1-cement : 3- coarse sand :6-Brick bats

40 + 50mm size) inside plastering 15mm thick with Cement Mortar 1:3 (1Cement : 3-coarse sand)

finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1-

Cement :2-Coarse sand :4-stone aggregate 20mm nominal size) finished smooth complete including

curing and festing (i) Inside size 900mm x 1200mm and 1.5M. deep including C.I. cover with frame

size 560mm diameter total weight of cover and frame to be not less than 128 kgs. (Wt. of cover 64 Kg.

and Wt. of frame 64 Kg.)(A) With 230mm thick walls of brick msonry using brick having crushing

strength not less than 35Kg. /Sq.cm. in Cement Mortar 1:5 (1- Cement: 5-Coarse sand)

(1) A type depth 0.90 Metre

131 2.00 (2) B type depth up to 1.50 Metre Each 19,139.07

132 2.00 (3) C type depth 2.25 Metre Each 23,209.64

Providing and fixing Urinal or approved quality including conecting the Urinal with waste pipe , tap

etc. complete. (A) White earthen ware flat back or corner type size 430mm x 260mm x 350mm

Providing and fixing 15mm dia C.P. bib cock of approved make like jaquar or Essess or any other type

134 36.00 and make specified by the Architect. All pillar cocks, stop cock, angle cock etc to be Jaquar or EssEss Each 750.00

make with quarter turn disc ceramic cartridge and chrome finish.

Providing and fixing C.P. brass angle valve for basin mixer of approved quality conforming to IS:8931

135 64.00 of Approved make as approved by engg. in charge all complete. Each 550.00

15 mm Nominal Bore Dia

Provdg. & laying S.W. Gully trap with C.I. garting brick masonry chamber & water tight C.I. cover

136 27.00 with frame of 300 mm x 300 mm size (inside) with standard weight. sqare mouth trap size 150 x100 Each 1,279.40

Providing erecting and fixing double coated ISI water tank of required capacity each with all necessary

fittings and connection etc. complete on terrace.

Sr. No. Item Description Unit Rate Amount

Constructing RCC Under Ground water tank(A) withExcavation &laying

Providing and Carting

controlled cement concrete

M250 mix for R.C.C. work including reinforcement, boxing, centering, vibrating, , PVC water stopper,

curing and mixed with approved water proofing cement compound or "CEMWET" or "PIDICRETE

LW" integral water proofing admixture as water proofing agent to be mixed with 50 kgs. bags shall be

as recommended by the manufacture of the water proofing material, concrete work for top, bottom slab

& side pardi for underground water tank item incl. Necessary excavation & refilling the available earth,

15 cm thk 1:2:4 for bedding of concrete, 20 mm thk. water proofing cement plaster in C.M. 1:3 with

smooth finishing & Glazes tile Dedo, vata, watering etc. Comp. to all face of tank . including locking

arrangement outlet, inlet, overflow and washout outlet pipe arrangement as necessary & C.I. Cover

0.60 x 0.45 weight not less then 35 kg with locking arrangement. etc. comp as per structural drawing

Including Reinforcement TMT-FE500D As per drawings and design supplied by architect and

instruction given by authority and E.I.C.

Constructing RCC Overhead water tank with Providing and laying controlled cement concrete M250

mix for R.C.C. work including reinforcement, boxing, centering, vibrating, , PVC water stopper, curing

and mixed with approved water proofing cement compound or "CEMWET" or "PIDICRETE LW"

integral water proofing admixture as water proofing agent to be mixed with 50 kgs. bags shall be as

recommended by the manufacture of the water proofing material, concrete work for top, bottom slab &

139 44,000.00 side pardi for Overhead water tank item incl. 20 mm thk. water proofing cement plaster in C.M. 1:3 Liter 10.00

with smooth finishing & Glazes tile Dedo, vata, watering etc. Comp. to all face of tank . including

locking arrangement outlet, inlet, overflow and washout outlet pipe arrangement as necessary & C.I.

Cover 0.60 x 0.45 weight not less then 35 kg with locking arrangement. etc. comp as per structural

drawing Including Reinforcement TMT-FE500D As per drawings and design supplied by architect and

instruction given by authority and E.I.C.

Providing and fixing cast iron (Spun) Nahni trap of the following nominal diameter of self cleaning

design with C.I. screaed down or higned grating including cost of cutting and making good the walls

and floor 100mm inlet and 50mm outlet.

Provdg. And fixing to wall, ceiling & floor in true line and level UPVC pipe Schedule- 40 of Prince

Supreme , astral , finolex or equivalent make as approved by engg. incharge. pipe shall be fix on wall

with the help of clamp at every twi meter center to center of shall be concealed as directed in cluding

neccesarry fitting etc. in cluding testing of pipe and jointd and fixing the same with adhesive

solvent, including cost of all materials of following nominal bore.

Sr. No. Item Description Unit Rate Amount

144 72.00 (D) 40 mm (A) Excavation & Carting Rmt 146.65

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having

National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube

fittings and clamps including making good the wall, ceiling and floor etc. complete.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot &

cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes &

152 51.00 fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per Rmt 1,674.40

direction of Engineer in Charge.

Provdg. And fixing to wall ,ceiling and floor 10.00 kg. F/Sq.Cm working pressure polythelene pipes

of the following outside diameter, low, density, complete with special flange compression type fittings,

wall clips etc. making good wall ceiling and floor.

Providing & fixing Wall-mounted European Closet Suite Cera 'Clair' model No 2035 P-Trap

(White/Light Coloured) with Dual Flush Tank, PVC pan connector, seat & lid (heavy duty) including

C.I. Brackets, C.P. Flush cock, C.P. brass hinges, All Internal fittings complete with rubber buffers,

C.P. nuts, bolts, ChaKi, etc making holes in walls & floors, & finishing for ready to use.The rate

includes Providing & fixing 15mm Angle Valve as per product detail with braided hose pipe as per

product detail, jet spray as per product detail including cutting and making good the wall where

required.(Ewc wall hung-p : Cera. (white/light coloured) Classic no.2037 or equivalent, Chair bracket

: Cera no:2434 or equivalent brand make, rag bolts, Dual Flush Cistern : Cera (white/light coloured)

no: 2608 or equivalent, Angle cock : Jacquar no 051continental or equivalent, Braided hose : Jaquar-

Allied-803B-CP)

Sr. No. Item Description Unit Rate Amount

Providing and Fixing Handicap Toilet set including EWC, Cistern,

(A) Excavation & Seat Cover, Fittings, Washbasin,,

Hinged Rail, Grab Bar and Faucet with Spatula Lever including Cast Iron chair backed and necessary

bolts and nuts complete, including painting of fittings and brackets, cutting and making good the walls

156 3.00 and floors wherever required to the satisfaction of Engineer-In-Charge. Special Needs Toilet Set: Each 40,986.00

Jaquar - CNS-WHT-755SN + Cistern Set CNS-WHT-207, Wash Basin CNS-WHT-811 & Grab Bar

2 No. - WAC-WHT-BG0800 & WAC-WHC-BR0600 - 2 nos.+ or Equivalent approved Make. Rates

includes all lead & lift as directed by EIC.

Providing and fixing chromium plated brass half trun flush cock of approved quality including fixing

157 28.00 in pipe line etc. complete. Each 261.16

Provdg. & fixing wash basin with signle hole for pillar tap with C.I. or M.S. brackets painted white

incl. cutting holes and making good the same . Incl. P/F C.P. brass waste pipe 32 mm dia M.I.Fisher

union of 32 mm dia. Pilar trap, capstren head, srew down high pressure with screw of 15 m dia etc.

comp.(550 x 400 mm size )

Providing and fixing beveled edge mirror of superior glass (of approved quality) complete with 6 mm

thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing C.P. brass towel rail comlete with C.P. brass brackets fixed to wooden plugs with

160 18.00 C.P. brass scews. Each 597.22

(B) 600mm x 20mm size.

Providing and fixing screw down bib taps of following size.

161 46.00 (A) Brass screw down bib tap polished bright. Each 212.68

Supplying & installing Brass handle Ball Valve conforming to IS 778, of RB, Italy or equivalent. Ball

valve must be having screwed ends. The ball valve should be with stand with maximum pressure up to

16 Kg/cm2. Complete job as specified & directed.

164 11.00 (iii) 50 mm dia Each 3,574.11

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end)

Providing and fixing pillar tap, capstan head, screw down high pressure with screws, shanks and back

Sr. No. Item Description Unit Rate Amount

Supplying and fixing reinforced concrete heavy duty nonpressure

(A) Excavation pipes with collars for culverts

169 28.00 carrying heavy traffic as per IS 458-1991 specifications including setting the pipes in C.M. 1:2 Mtr. 643.49

watering and laying (to level or slopes) of class NP3 of following internal daimeters.(i) 300mm dia.

Constructing Bombay Pattern Type Catch Pit of size 0.60 x 0.60 depth up to 1 mt including

excavation, B.B.C.C. (1:5:10), 23 cms thick brick maso. wall in the prop. of CM (1:6) with 40 mm

thick IPS flooring in the prop M15 at bottom and 15 mm thick cement plaster inside the catch pit in the

proportion of CM (1:3) with out jali etc. comp. as directed.

CatchPit Jali Fixing P/F FRC catch pit jali with frame 600mm x 600mm clear opening etc. comp.. As

directed by engineer in charge.

Total Amount of Civil, Plumbing & Site Development Work

Total Amount of Civil, Plumbing & Site Development Work

Ahmedabad Municipal Corporation

Proposed Construction of New Gymnasium, Library and Physiotherapy Center at TP - 35, FP – 42 (Social Infrastructure Purpose) in

Chandlodiya Plot of North West Zone, Ahmedabad Municipal Corporation.

BOQ of Electrical Work

SR. No. Description of Work Unit Rate Amount

Point wiring for Light / Bell with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of ISI marked

1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected

concealed in/ on surface on wall/ceiling complete with 6A Modular type switch / bell push & accessories and

earth continuity of following type, erected on PVC / Metallic box, single mounting base frame covered with

textured/metallic front plate modules erected on / in wall / ceiling as per pipe erected, with necessary Lamp

holder/ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete.

Wiring for the light points as above but with IP66 Switch board with IP 66 Box and 6 Amp / 16 amp

2 E-2 Switch. 250 Volt one 6 A IP66 switch located on IP 66 box board of Legrand cat. No. 673000 & 684638 2.00 Nos. 2,040.00

3 E-3 Primary light point controlled by one SP MCB (Same as above item but controlling with SP MCB) 2.00 Nos. 525.00

Point wiring for secondary light point with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (green) both are of ISI

marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected

concealed in / flushed on wall/ceiling, complete with earth continuity and necessary connection with primary

light with accessories erected on Metal / PVC box covered with 3 mm thick PC(Polycarbonet) / Acrylic

sheet for open / concealed wiring. with necessary Lamp holder / ceiling rose / H.D.Connector as directed.

(a) with medium class Rigid PVC pipe and accessories

Point wiring for Two Way Controlled Light Point with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (green) both

are of .ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to

be erected concealed in / flushed on wall/ceiling ,complete with 6A Modular type switches and following

5 E-5 type of accessories erected on PVC / Metallic box, single mounting base frame covered with textured / 2.00 Nos. 562.00

metallic front plate modules erected on / in wall / ceiling as per pipe erected. with necessary batten/angle

holder or ceiling rose or H.D.Connector as directed.

(a) with medium class Rigid PVC pipe and accessories

6 E-6 Do as above but for Secondary light point controlled by same two way switch 2.00 Nos. 192.00

SR. No. Description of Work Unit Rate Amount

Point wiring for FAN with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of .ISI marked 1.1 KV

Grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in /

flushed on wall/ceiling complete with 6A Modular type switch and hum free EME four or more step type

electronic fan regulator with separately mounted and accessories with earth continuity of following type

erected on PVC / Metallic box, single mounting base frame covered with textured/metallic front plate

modules erected on / in wall / ceiling as per pipe erected. with necessary ceiling rose / H.D.Connector as

(a) with medium class Rigid PVC pipe and accessories

Point wiring for Looped Plug with 6A Modular type switch & 5 pin socket erected on PVC / Metallic box,

8 E-8 single mounting base frame covered with textured / metallic front plate modules erected on / in wall / ceiling 30.00 Nos. 255.00

with following type accessories

Do - As - Above but for 6 A x 5 pin 250 Volt switched socket outlet point at convenient location. ( Plug &

Switch can be together or at different location )

Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV

grade FRLS PVC insulated multistrand copper wires, in following type of to be erected concealed in / on

surface of wall / ceiling complete with Modular type switch & 5 pin Plug erected on PVC / Metallic box

10 E-10 covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with following 48.00 Nos. 704.00

type of accessories.

[II] For 16A Plug with 2-2.5 sq.mm Cu. Wire

(a) with medium class Rigid PVC pipe and accessories

Wiring for the 250 volts single phase and neutral 16 amps switched socket outlet with 4.0 sq.mm

FRLS flexible copper conductor 1100 volts grade wires of approved make with concealed or surface

11 E-11 mounted 25 mm dia medium gauge PVC Conduit including providing and fixing of 16 amps 5 pin switch 2.00 Nos. 829.00

socket outlet of approved quality color make & design in 2 mm thick GI box and earthing of fixtures

and the outlet box with 2.5 sq.mm PVC insulated copper conductor stranded flexible "FRLS" wire.

Wiring for the UPS / Comp. / Raw Power outlet with 2 nos. of 250 volts single phase and neutral 16 amps

switched socket outlet with 2.5 sq.mm x 3 core FRLS flexible copper conductor 1100 volts grade

wires of approved make in concealed or surface mounted Prelaid 25 mm dia medium gauge PVC Conduit

/ Race ways including providing and fixing of 2 no's of 16 amps 5 pin switch socket outlet of approved

quality color make & design in 2 mm thick GI box and earthing of fixtures and the outlet box. (

Maximum 3 nos. of Plugs can be looped in 1 Circuit )

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected

on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution &

Clamps with following dia of pipes, in approved manner as directed

Supply and laying of 25 mm rigid PVC pipe of 1.6-1.8 mm thickness

14 E-14 Supply and laying of 32 mm rigid PVC pipe of 1.6-1.8 mm thickness 250.00 Rmt 52.00

15 E-15 Supply and laying of 40 mm rigid PVC pipe of 1.6-1.8 mm thickness 150.00 Rmt 64.00

SR. No. Description of Work Unit Rate Amount

MAINS : ( not for Point wiring )

Supplying and Laying of mains with Cu. PVC insulated flexible wire with ISI and FIA approval for 650 V/

1100 V with earth wires of Cu. PVC insulated flexible wires with ISI approval for 650 V/ 1100 V as earth

wires with Suitable dia rigid PVC Pipe of Heavy Gauge ( Scope Also includes Supply of pipe. )

Supplying and Laying of 4 nos. of 10 sq mm Cu. FRLS flexible wires with 2 nos 4 sqmm Cu. FRLS

flexible wireswith 40 mm dia Pipe

Supplying and Laying of 2 nos. of 6 sq mm Cu. FRLS flexible wires with 1 nos 2.5 sqmm Cu. FRLS

flexible wires with 40 mm dia Pipe

Supplying and Laying of 2 nos. of 4 sq mm Cu. FRLS flexible wires with 1 nos 2.5 sqmm Cu. FRLS

flexible wires with 25 mm dia Pipe

Supplying and Laying of 2 nos. of 2.5 sq mm Cu. FRLS flexible wires with 1 nos 1.5 sqmm Cu. FRLS

flexible wires with 25 mm dia Pipe

Supplying and Laying of 2 nos. of 1.5 sq mm Cu. FRLS flexible wires with 1 nos 1.5 sqmm Cu. FRLS

flexible wires with 25 mm dia Pipe

Distribution Board

Supply, Assembling, grouting, leveling Connecting & testing D.B of IP 54 of specified make.

Distribution Board-VTPN

Supply, Erecting, testing and commissioning of only VTPN D.B. with space for FPMCCB / FPMCB as

incoming and 4 TPMCB / SPMCB as outgoing per phase (i.e. 4 way VTPN D.B.) of Legrand Make Cat.

Distribution Board-TPN

Supply, Erecting, testing and commissioning of only TPN D.B. PPI type with space for FPMCB as incoming

and space for DPELMCB and 4 SPMCB as outgoing per phase (i.e. 8 way per phase D.B.) of Hensel Make

Distribution Board-SPN

23 E-23 Supply, Erecting, testing and commissioning of SPN D.B. PPI type with space for DPELMCB as incoming 4.00 Nos. 3,860.00

and 8 SPMCB as outgoing per phase (i.e. 12 way D.B.) of Hensel Make KV9112M

Supply, Erecting, testing and commissioning of SPN D.B. PPI type with space for DPELMCB as incoming

and 4 SPMCB as outgoing per phase (i.e. 8 way D.B.) of Hensel Make KV7109M

All MCB's, ELMCB's, ELCB's should be of 10 KA only

providing and erecting Miniature circuit breaker single pole 0.5A to 2A system and having breaking capacity

10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark

SR. No. Description of Work Unit Rate Amount

Providing & erecting 415 V MCB three Pole for Motor & Inductive Load (C Curve) having 10KA breaking

32 E-32 capacity & confirms to IS :8828 in existing box having following capacity 5.00 Nos. 582.00

(a) 6 to 32 Amp. Cat.III

Providing & erecting 415 V MCB three Pole for Motor & Inductive Load (C Curve) having 10KA breaking

33 E-33 capacity & confirms to IS :8828 in existing box having following capacity 5.00 Nos. 641.00

(b) 40 Amp. Cat.III

Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) having 10KA breaking

34 E-34 capacity & confirms to IS :8828 in existing box having following capacity 5.00 Nos. 590.00

6 to 32A FP MCB

Providing and erecting Approved make Four pole moulded case circuit breaker having breaking capacity ICU

of 25 KA. at 415 V,having normal current rating up to 25 A to 100A. with Fixed thermal & magnetic release

37 E-37 suitable to work on A.C. supply 50 c/s. with all internal connections, spreader tinned copper & complete 2.00 Nos. 6,112.00

erected in existing 16 G.M.S. housing. .

ICS= 100% of ICU only.

Supplying & erecting approved make Digital time switch having lithium cell 6 years operative and operate

battery backup 1 channel day clock with 14 memory programme, suitable to operate on 240V + 5%, 16A

38 E-38 with, floating contacts Minimum switching setup time 1 minimum & LCD display. Also comprised 2.00 Nos. 3,137.00

permanent ON/OFF switching. Programming switches & housed in fire proof thermoplastic enclosure &

transparent cover erected as required with necessary connection erected as directed.

39 E-39 25 Amp DP Dinrail Mounted Contactor 2.00 Nos. 2,234.00

40 E-40 40 Amp FP Dinrail Mounted Contactor 2.00 Nos. 3,674.00

41 E-41 SITC of IP65 Polycarbonate enclosure for DP MCB 2.00 Nos. 1,882.00

42 E-42 SITC of IP65 Polycarbonate enclosure for FP MCB 2.00 Nos. 1,995.00

Making trench in soft soil of suitable width of 90 cms deep for laying cable or locating the fault all over the

43 E-43 run and backfilling the same and making the surface proper. Providing and erecting iron clad cable route 350.00 Meter 55.00

marker duly marked with ELE.CABLE of size 23 cms.X 12 cms. Flushed with ground in cement foundation

as directed by Engineer in charge. The width shall be as per requirement

Covering of cable with second class bricks laid cover the cable crosswise & also on both sides with covering

of 7. 5 Cms. layer of sand above & below cable (cable shall be laid in 0.9mtr.deep & 0.4 Mtr.wide trench).

Where there are more than one cable in the trench on either side of the cable, 5 Cms. over lapping of bricks

shall be provided.

SR. No. Description of Work Unit Rate Amount

Construction of brick masonry pulling chamber 600 mm x 600 mm inside clear size and depth up to

meter with 350 mm thick masonry in cement mortar proportion 1:5,cement finish cement plaster in CM

proportion of 15 mm thickness from inside with 150 mm thick PCC at bottom with top slab minimum

45 E-45 mm thickness in M20 grade with reinforcement. The rate shall be inclusive of providing and fixing frame and 4.00 Nos. 10,423.00

600 mm dia cover of FRC for the Heavy Duty. Rate also inclusive of excavation and back filling & clearing

the site by removing debris & Shifting of the debris & making site good As per the Instruction of the

Engineer In charge complete in all respect.

Construction of brick masonry pulling chamber 750 mm x 750 mm inside clear size and depth up to

meter with 350 mm thick masonry in cement mortar proportion 1:5,cement finish cement plaster in CM

proportion of 15 mm thickness from inside with 150 mm thick PCC at bottom with top slab minimum

46 E-46 mm thickness in M20 grade with reinforcement. The rate shall be inclusive of providing and fixing frame and 8.00 Nos. 13,138.00

750 mm dia cover of FRC for the Heavy Duty. Rate also inclusive of excavation and back filling & clearing

the site by removing debris & Shifting of the debris & making site good As per the Instruction of the

Engineer In charge complete in all respect.

Construction of brick masonry pulling chamber 1000 mm x 1000 mm inside clear size and depth up to

meter with 350 mm thick masonry in cement mortar proportion 1:5,cement finish cement plaster in CM

proportion of 15 mm thickness from inside with 150 mm thick PCC at bottom with top slab minimum

47 E-47 mm thickness in M20 grade with reinforcement. The rate shall be inclusive of providing and fixing frame and 12.00 Nos. 16,746.00

900 mm dia cover of FRC for the Heavy Duty. Rate also inclusive of excavation and back filling & clearing

the site by removing debris & Shifting of the debris & making site good As per the Instruction of the

Engineer In charge complete in all respect.

Fabricating the box type items made from M.S. Sheet with A.I. supports, wings, doors, handles other

48 E-48 hardware materials as per requirement design with finishing by three tank powder coating processed inside 500.00 Kg 179.00

and outside painted, erected as directed including minor civil work.

Supply, Installation, Testing, Laying, Commissioning of following 1100 volt grade XLPE insulated PVC

sheathed aluminum / Copper conductor armored cables as per (IS:7098)(I)-88 ISI marked & specification in

trenches, cable trays, ducts, over bed of sand, clamped to wall with suitable clamps including, saddles fixing

bolts, connecting testing and commissioning with identification tags at every 10 mtr. & Both ends. with All

the fixing accessories, excavation Back filling & Cable protection with Bricks as per the drawing ( If

70 sq.mm x 3.5 c Al. XLPE Arm. Cable

50 E-50 50 sq.mm x 3.5 c Al. XLPE Arm. Cable 50.00 Meter 282.00

51 E-51 25 sq.mm x 4 c Al. XLPE Arm. Cable 80.00 Meter 189.00

52 E-52 16 sq.mm x 4 c Al. XLPE Arm. Cable 850.00 Meter 152.00

53 E-53 10 sq.mm x 4 c Al. XLPE Arm. Cable 500.00 Meter 139.00

54 E-54 6 sq.mm x 4 c Cu. XLPE Arm. Cable 150.00 Meter 505.00

SR. No. Description of Work Unit Rate Amount

Providing & erecting XLPE(IS:7098) (I)-88 ISI armoured cable multistrand copper conductor for 1.1 KV.

To be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following

6 sq.mm x 3 c cu. XLPE Arm. Cable

Providing & erecting XLPE(IS:7098) (I)-88 ISI armoured cable multistrand copper conductor for 1.1 KV.

To be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of following

4 sq.mm x 3 c cu. XLPE Arm. Cable

57 E-57 Supply & Laying of 1.5 sq mm x 3 core round flexible wire in prelaid pipe / Raceway. 200.00 Meter 46.00

58 E-58 Supply & Laying of 2.5 sq mm x 3 core round flexible wires in prelaid pipe / Raceway. 75.00 Meter 77.00

59 E-59 Supply & Laying of 4 sq mm x 4 core round flexible wires in prelaid pipe / Raceway. 30.00 Meter 175.00

Cable Termination

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor

60 E-60 armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, 2.00 Nos. 197.00

double compression type Brass glands with earthing.

70 sq.mm x 3.5c Al. XLPE Arm. Cable

61 E-61 50 sq.mm x 3.5 c Al. XLPE Arm. Cable 2.00 Nos. 150.00

62 E-62 25 sq.mm x 4 c Al. XLPE Arm. Cable 2.00 Nos. 111.00

63 E-63 16 sq.mm x 4 c Al. XLPE Arm. Cable 44.00 Nos. 107.00

64 E-64 10 sq.mm x 4 c Al. XLPE Arm. Cable 16.00 Nos. 90.00

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor

armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs,

double compression type Brass glands with earthing.

6 sq.mm x 4 c Cu. XLPE Arm. Cable

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor

armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs,

double compression type Brass glands with earthing.

6 sq.mm x 3 c Al. XLPE Arm. Cable

SITC of Cable end termination of the following XLPE insulated PVC sheathed aluminum/copper conductor

armored cables of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs,

double compression type Brass glands with earthing.

4 sq.mm x 3 c Al. XLPE Arm. Cable

SITC of Round Flexible wire end termination of the following insulated PVC sheathed copper conductor

Wires of 1100 volt grade including supplying and fixing of bimetallic Long neck crimping lugs, IP66 / 67 -

3 mm thick Thermoplastic long entry glands of Hensel / Spelsberg with Strain relief and Lock nut.

1.5 / 2.5 Sq. mm x 3 / 4 core round flexble wire or Similar dia wire

69 E-69 4 / 6 Sq. mm x 3 / 4 core round flexble wire or Similar dia wire 4.00 Nos. 51.00

SR. No. Description of Work Unit Rate Amount

MV Switchgear & Power Panels

Supply, Unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, &

Commissioning main L.T. panel board, fabricated from M.S. sheet & folded channel totally enclosed cubical

type compartmentalized. Scope Covers Unloading at Site, Store in Weather Proof Condition, Shift to the

Location Basement / GF / FF, Grouting, Installation, Testing & Commissioning complete in all respect & As

per the instruction of Architect / Consultant / Engineer Incharge. Scope also covers Co ordination with Panel

Design, fabrication, assembling, supply, installation , testing of Panels for 415 V, 3 phase, 50 Hz, 4 wire

power supply system.

Panels shall be fabricated out of 2 mm thick CRCA sheet steel in cubical formation, compartmentalized in

Form 4b Construction, floor mounted, free standing and shall be dust and vermin proof. 3 mm thick cable

gland plate, shall be provided both at the top and the bottom of the panel.

All large panels shall be provided with lifting hooks. Distribution panels shall be fabricated in accordance

with the specifications.

Note : Panel vendor has to provide Surge Protection at every stage of the Distribution.

1) Supporting rigid steel framework.

2) Cubicle type, 14 gauge CRCA sheet steel enclosed.

3) Complete with interconnections and distribution bus bars.

4) Proper bonding to earth.

5) Painting/lettering on Breakers and distribution boards, the location they serve, providing on each panel

its circuit diagram.

6) Providing cable clamps / supports within distribution boards cable alley.

7) TPN ACB’s / MCCB’s shall mean 3 pole ACB’s / MCCB’s with adequate size of neutral link.

8) All MCB’s shall be of minimum 10 KA breaking capacity.

9) The breaking capacity of MCCB’s are mentioned panel wise.

10) All motor feeders MCCBs shall be of motor duty.

11) Distribution panels shall be Powder Coated with Siemens gray paint shade no. RAL-7032 of IS-5.

12) Degree of protection for following type of distribution panel enclosure shall be as per IS:13947-1993.

a) IP 52 for indoor panels.

b) IP 54 for Service area panels.

c) IP 65 for outdoor panels.

13) All MCCB’s shall be provided with operating mechanism for door interlock & with the roraty handle.

14) Current density of aluminium shall be 1 sq mm for 0.8 amps for rated current of bus bars and current

density of copper shall be 1 sq.mm for 1 amps for rated current of bus bars.

15) Tinned copper earth bus as specified in the BOQ / SLD shall be provided through out the length of each

SR. No. Description of Work Unit Rate Amount

16) All measuring instruments (Meters) shall be of digital electronic with LED of approved make and

compatible with BAS.

17) All hinged door shall be earthed through 2.5 sq mm tinned braided copper wire.

18) All panels shall have provision of the following:

a) IP 55 for outdoor panels.

b) Pad locking of MCCB’s handles in “OFF” Position.

19) Additional set of C.T.s, potential free contacts, connectors, contactors with wiring etc are to be provided

for BAS including space required for various transducers in Main Switch Board sections. Only transducers

shall be supplied by BAS contractor.

20) All the C.T.s should be auto short link type.

21) All the MCCB's should be with rotary handle.

22) All MCB’s used for protection of resistive and lightly inductive load shall be type “B” characteristic and

inductive (motor) load shall be of type “C” characteristic and discharge lamps and UPS etc. shall be of type

D characteristic.

23) All incoming and outgoing air circuit breakers shall be placed on middle portion of the vertical in single

tier formation.

24) All PTs / control transformer shall be provided with centre tap earth secondary.

25) If Any descripancy found in SLD & BOQ, it should be brought in the notice of the Client / Consultant,

Client / Consultant's decision will be final in case of any descripancy.

26) All outdoor panles should be provided with minimum 600mm height fabrication stand with all side 2mm

thick M.S. powder coated sheet.

27) G.A. Drawing should be checked & Finalised by consultant before fabrication.

SR. No. Description of Work Unit Rate Amount

SITC of Main LT Panel

Incoming : From Supply Co. Meter

250 amps FP MCCB (25 KA) with following accessories: 1 Sets

i. LED type Phase indicating & ON, OFF light shall be protected by 2 amps SP MCB's. - 5 nos.

ii. 3 Nos. of Digital type 0-500 / 5 amps CTR digital ammeter with 3 nos 250 / 5 amps, 15 VA Class I CT’s.

iii. Digital type 0-500 Volt digital voltmeter with inbuilt selector switch & shall be protected by 2 amp TP

70 E-70 iv) KWH Meter 1.00 Nos. 1,98,000.00

250 amps FP Cu. Tinned bus bars with colored heat shrinkable insulated sleeve.

63 amps 4 pole MCB (10KA) : 4 Nos.

40 amps 4 pole MCB (10KA) : 10 Nos.

6 to 32 amps 2 pole MCB (10 KA) : 8 Nos.

Panel should be as per SLD & Specifications

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming to IS: 513/CRCA/

aluminium die cast powder coated and high U.V. & corrosion resistance with diffuser with company

mark/name 160V to 270V, Power Factor more than 0.9, THD < 15%, CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED LED driver efficiency > 85 % ( fitting required LM-79 & LM-80

Certificates) (NOTE: Below description have shown ranges of Wattage capacity of LED fittings.The

Engineer incharge may select any wattage capacity between the ranges shown.)

(A) Tube Light with integral driver

(iv) 22-24 Watts, Surge - 2KV,IP-20, conventional 4 feet, Cat-III

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming to IS: 513/CRCA/

aluminium die cast powder coated and high U.V. & corrosion resistance with diffuser with company

mark/name 160V to 270V, Power Factor more than 0.9, THD < 15%, CCT 3000 K to 6500K,

72 E-72 Luminaire efficacy> 85 lumens/watt ,LED LED driver efficiency > 85 % ( fitting required LM-79 & LM-80 5.00 Nos. 530.00

Certificates) (NOTE: Below description have shown ranges of Wattage capacity of LED fittings.The

Engineer incharge may select any wattage capacity between the ranges shown.)

(A) Tube Light with integral driver

(v) 36-40 Watts, Surge-2 KV, IP-20, conventional 4 feet, Cat-III

SR. No. Description of Work Unit Rate Amount

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder coated and high U.V. & corrosion resistance with diffuser

housed in aluminium casted body with company mark/name 160V to 270V,Power Factor more than 0.9,

THD < 15 %, CCT 3000 K to 6500K, Luminaire efficacy> 85 lumens/watt , LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may select any wattage capacity between the ranges shown.)

(A) Square/ Circular shaped Surface/Recessed Mount Downlight with provision for spring loaded mounting

clips complete.IP20

(i) 5-9 watts,Surge-2 KV

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder coated and high U.V. & corrosion resistance with diffuser

housed in aluminium casted body with company mark/name 160V to 270V,Power Factor more than 0.9,

THD < 15 %, CCT 3000 K to 6500K, Luminaire efficacy> 85 lumens/watt , LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may select any wattage capacity between the ranges shown.)

(A) Square/ Circular shaped Surface/Recessed Mount Downlight with provision for spring loaded mounting

clips complete.IP20

(iii) 16-20 watts, Surge-2 KV

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder coated and high U.V. & corrosion resistance with diffuser

housed in aluminium casted body with company mark/name

160V to 270V,Power Factor more than 0.95, THD < 15 %,

CCT 3000 K to 6500K,

75 E-75 Luminaire efficacy> 85 lumens/watt , 108.00 Nos. 1,777.00

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may select any wattage capacity between the ranges shown.)

(B) LED Panel Light with provision for Plane front frame with translucent cover fixed to housing

(vi) 36 watts, 24" x 24", Surge- 2KV

SR. No. Description of Work Unit Rate Amount

Supplying and erecting LED street light / Flood light fittings with High power White LEDs wattage of

Watt and above assembled on single MCPCB, efficiency more than 130 lm/w and corrosion free High

pressure die cast aluminum housing with smooth finish powder coated and heat sink extruded aluminium

with diffuser and Polycarbonate optics/ lenses, with toughened glass with company mark/name engraved or

embossed 160 to 270 V,Power Factor more than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity

76 E-76 ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED driver efficiency > 85 %.( fittings required LM-79 25.00 Nos. 4,948.00

& LM-80 certificates)(NOTE: Below description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity between the ranges shown.)

(A) Street Light (IP-65), Surge protection -4KV integral and ,Light must have 440VAC line supply with

over-voltage protection.

(ii) above 48 to 60 Watts

Providing and erecting PVC body surface or pendent mounting LED Bulk type 9 watt Lighting Fitting with

electronic driver. And lumen output from luminaire 720lm , input voltage range 90-300VAC , 50Hz cool

white(3000 to 6500k), inbuilt driver, -20degC to +60degC working temperature, AL frame with Beam Angle

Supplying and erecting LED street light / Flood light fittings with High power White LEDs wattage of

Watt and above assembled on single MCPCB, efficiency more than 130 lm/w and corrosion free High

pressure die cast aluminum housing with smooth finish powder coated and heat sink extruded aluminium

with diffuser and Polycarbonate optics/ lenses, with toughened glass with company mark/name engraved or

embossed 160 to 270 V,Power Factor more than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity

78 E-78 ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED driver efficiency > 85 %.( fittings required LM-79 8.00 Nos. 10,711.00

& LM-80 certificates)(NOTE: Below description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity between the ranges shown.)

(B) Flood Light (IP-65), Surge protection -4KV integral and ,Light must have 440VAC line supply with

(vii)above 200 to 250 watts

79 E-79 Supplying & erecting approved make low noise decorative exhaust fan having size 200mm with 1350 RPM 9.00 Nos. 1,687.00

with square frame ABS body with inbuilt lowers & square frame.

Supplying & erecting single phase approved make industrial exhaust fan suitable for medium duty ring

mounted low noise operation suitable for medium duty having following dia size and maximum speed in

[A] 305 mm dia 900 RPM

81 E-81 Providing suitable M.S. louver shutter of the Exhaust fan. 10.00 Nos. 365.00

SR. No. Description of Work Unit Rate Amount

Providing & erecting Approved make Ceiling Fan with double ball bearing ISI mark with Condenser

82 E-82 volt A.C.50 Hz. 1200 mm sweep complete having 4 blades Aluminium body and blade sets having 81.00 Nos. 2,335.00

ornamental design shanks, canopy erected with earthing [ Make shall be approved by Engineer in Charge]

Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe down rod erected duly painted

for fan complete with necessary 24/ O.20, 3 core flexible wire with earthing.

Supplying and erecting approved make Conical Pole (Standard ) Made from HR sheet steel. The pole should

be made as per IS. and shall be coated with hot dip galvanizing as per IS 2629/2633/4759 with required

base plate and integral Junction box consist of terminal plate of min 6mm Hylam sheet, standard profile

35mmX7.5mm Din-Rail for MCB Mounting, stud type terminal and arrangement for cable terminationas

erected on suitable foundation (included) with necessary GI nut-bolts/J-Bolts. as per details given by

manufacturer considering site requirement.The length of poles are as below.

(B) 4 Mtr. Long 65mm Top X125 mm bottom dia, 3mm thickness.

85 E-85 (D) 6 Mtr. Long 65mm Top X155 mm bottom dia, 3mm thickness. 20.00 Nos. 8,670.00

Supplying and erecting Street light pole bracket comprising main B Class GI pipe of 4.2 cm/require outside

dia. complete with suitable B Class G.I. sleeve tubing of approx. 45cms.length and suitable for

76.5mm/80mm/require size of pole top having nuts and bolts for fixing the brackets and having spread of

86 E-86 mtr. Length with 110 deg.with vertical plane and suitable welded stiffener reducer and nipple with check nut 18.00 Nos. 487.00

complete painted with one coat.of Red oxide / PU base primer and two coats of Aluminium / PU paint. paint

with following nos of arms.

[A] Single Arm bracket 0.5 Mtr

87 E-87 [B] Double Arm Bracket 0.5 Mtr 2.00 Nos. 616.00

Providing cement concrete.for foundation or for concrete filling in 1:2:4 ratio with 20 to 25 mm stone metal

duly plastered with necessary curing for pole muffing or any other purpose.

89 E-89 TMT Bar for Pole Foundation 322.43 Kg 75.46

Supplying & erecting funnel type earthing having earth plate of following size burred in specifically

prepared earth pit 3 mtr. below ground with 40 kg. charcoal and salt with alternate layers of charcoal & salt,

20mm.dia. G.I. pipe with Funnel with a wire mesh for watering & bricks masonry block, C.I. Cover

90 E-90 complete as per para 7.3 of IS 3043 with necessary length of double Galvanised Iron / copper earth wire No 2.00 Nos. 7,797.00

6 SWG bolted with lug to the plate and covered in 12 mm dia. G.I. pipe 2.5 mtr long complete connected to

the nearest switch gear with end socket as per direction & duly tested by earth tester confirming to IS (As per

drawing) with following specification

60 x 60 x 0.315 cms. Copper earth Plate

91 E-91 45 x 45 x 0.35 cms. C.I. earth plate 2.00 Nos. 2,543.00

SR. No. Description of Work Unit Rate Amount

Supplying & erecting in earthpit of minimum bore dia. 225mm size ASH or approved make Safe Earthing

Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of corrosion free G.I.Pipes having

Outer pipe dia of 80 mm having 80-200 Micron galvanising, Inner pipe dia of 40 mm having 200-250

Micron galvanising, connection terminal dia of 14 mm with constant ohmic value surrounded by highly

conductive compound with high charge dissipation suitable for following type of applications.

For Electrical Installation covering Transformer Neutrals, Lightning arrester Earthing, A.C.Plant & Sensitive

Computer System (like Automation, SCADA) i.e. independent Earthing located in other than normal soil i.e.

Soft Rock, Marshy Soil etc..

- Length of Pipe : 3 Mtrs.

- Back filling Compound :2 nos Bags of 25 Kg.

Earth wire/strips :

Supply and laying cu. earthing strips for interconnecting the earthing stations, panels, DB's etc. in built up

trenches, on walls/ceiling, buried in ground generally as specified and shown on drawings complete with :

fixing accessories

Corrosion protection of buried conductors with bituminous coating and covered with PVC tapes.

Providing and erecting HOT deep Galvanized strip iron wire 8 to 16 S.W.G.

96 E-96 No.8 gauge bare cu. earth wire 25.00 Kg 815.00

97 E-97 Earth Link : 40mm x 6 mm earth link fixed by necessary screws on wall. 4.00 Meter 370.00

SITC of Water Tight Junction Box With necessary clamp for mounting of the J.B. (All the cable / wire

connections to the JB shall be with the Water tight Glands only)

Telephone Outlet Point

SITC OF PowerCat 6 DataGate Jack, 568A/B - Yellow with Dust Cover / Blank/ One Telephone Point to be

99 E-99 done with Cat -6 Information outlet Socket, Back Box, Face Plate for all telephone point. Average Length to 14.00 Nos. 159.00

be considered as 50 Meter. Cable Laying, Labling, Ferrule, Testing, Certification to be included in cost.

Years of Certification is required. Test reports of Level-4 Scanners only.

SITC OF DG+ Jack (Diecast)Cat6A 568A/B, Shtd- Black (Information Outlet for Data) with Faceplate,

100 E-100 back box CAT-6A standards. Cable Laying, Labling, Ferrule, Testing, Certification to be included in cost. 13.00 Nos. 159.00

20 Years of Certification is required. Test Reports of Level-4 Fluke Scanners Only.

SITC of Jack Panel, fully loaded with 24 nos. UTP ports for PCB based IO Jacks (RJ45, TIA-568C

Category-6, Installation and Termination of all 24 nos. Catergory-6 UTP , unloaded with individually

replaceable 24 nos. Category-6 I/O Jacks complying with TIA-568.C.2, as per given jack specification Shall

be suitable for loading unshielded & shielded jacks for different category systems (CAT 6 & CAT 6A)

SR. No. Description of Work Unit Rate Amount

Supply and laying of PowerCat 6A U/FTP CM 4 Pair Cable, LSZH Sheath - Violet of specified make to be

done in prelaid PVC pipe of 25 mm dia / raceway of specified make, but without the cost of raceway or pipe

(the wire is to be drawn from HUB \ Switch of respective area to outlet point) with the cost of the crimping

with material of make Legrand / Molex/ Systimax / Panduit / Siemon

Fire Detection System

Supply, Installation, Testing And Commissioning of UL864, 10th Edition Microprocessor based 1 loop,

True Peer-to-Peer Networkable Addressable Fire Alarm Control Panel with minimum 50 characters LCD

display, 2000 event plus 500 alarm log history events, QWERTY keypad for programming. The panel

should be equipped with sufficient numbers of loops considering 20% spare capacity in each loop. Each loop

shall have a capacity of minimum 50 analog addressable devices. The panel shall work in degrade mode in

case of CPU failure, Products not having this feature may offer Redundant CPU. Four access levels, flash

EPROM, 240 volts AC power supply, automatic battery charger, 24 volts sealed lead acid batteries sufficient

for 24 hours normal working and 30 mins in alarm condition. The panel shall be compatible with Integrated

8 channel Digital Voice Evacuation System Controller capable of broadcasting Evacuation Messages on

same peer-to-peer Network and 2 ways Communication Fire Fighters System capable of supervising all the

speaker circuits with adequate zone control and accessories. Failure of Fire Panel CPU shall not result in

failure of DVC operation. The Fire Fighters Telephone System shall be capable of having minimum

Telephones in conference in multiple FFT Risers.

Supply, Installation, Testing And Commissioning of UL Listed Graphics User Interface for Monitoring &

Control of complete Fire, Voice Evacuation & Telephone Talkback System. The GUI based main network

software shall network with other panels on True Peer-to-Peer network. It shall be capable of graphically

representing each facility being monitored with floor plans and icons depicting the actual locations of the

various systems, and / or sensors’ locations. It shall have the facility to change the sensitivity of any detector.

104 E-104 The software shall be capable of monitoring 100 Nodes with 100 Mbps Transmission rate on Fibre Optics 1.00 Nos. 35,000.00

Network and 12 Mbps Transmission on cable and 1,00,000 network points. The software shall be capable to

Monitor & Control all the Digital Voice Evactuation as well as 2 way communication from main control

room using voice signals over Fire Network along with the Fire detection signal. The Graphic workstation

shall act as an independent node communicating on the peer to peer network and shall not be dependant on

the Fire Panel CPU for operation. Failure of Fire Panel CPU shall not result in failure of GUI.

Supply, Installation, Testing And Commissioning of Automatic printer capable for interface with NCS and

provided with RS 232/RS 485 protocol port. It shall be standard cartage with 80 characters per line as per

all requirements of technical specifications & contracts works.

SR. No. Description of Work Unit Rate Amount

Supply, Installation, Testing And Commissioning of UL268, 7th Edition Addressable Multi-criteria Photo-

Thermal Detector with sensitivity range of 0.5 to 4.0% obs/ft.The intelligent multi criteria detection device

shall include the ability to combine the signal of the thermal sensor with the signal of the photoelectric signal

in an effort to react hastily in the event of a fire situation. It shall also include the inherent ability to

distinguish between a fire condition and a false alarm condition by examining the characteristics of the

thermal and smoke sensing chambers and comparing them to a database of actual fire and deceptive

phenomena. The detector shall have twin bi-colour LED for 360 deg viewing. Addressing shall be with user

friendly rotary decimal switches.

Supply, Installation, Testing And Commissioning of UL listed Addressable Manual Call Point (Pull down /

107 E-107 Break Glass Type). The device shall have an LED which shall blink in normal state & get steady on 2.00 Nos. 3,446.00

activation to monitor the heath status of the device.

Supply, Installation, Testing And Commissioning of UL Listed Sounder cum Strobe rated at 80 dBA @ 3m

for Audible annunciation and 115cd flashintg at 1 Hz for visual indication. UL Listed

Supply, Installation, Testing And Commissioning of Addressable Control Module for Sounders / Strobes /

Sounder cum Strobes. The control module shall provide supervised NAC output rated at 24v DC, 2A. The

109 E-109 device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath 1.00 Nos. 4,191.00

status of the device. Addressing shall be with user friendly rotary decimal switches. Module shall be supplied

with mounting plate from OEM for ease of installation & maintenance.

Supply, Installation, Testing And Commissioning of UL Listed Isolator Module for Isolating short / dewired

/ loose circuits with automatic resetting arrangement. Isolator Base can also be proposed, however in that

110 E-110 case needs to be considered with each detector & module. The device shall have an LED which shall blink in 10.00 Nos. 3,635.00

normal state & get steady on activation to monitor the heath status of the device. Module shall be supplied

with mounting plate from OEM for ease of installation & maintenance.

Supply, installation, testing & Commissioning of Battery pack suitable for back up of 4 hours with charger

in case of Alarm condition.

112 E-112 Supply, installation, testing & Commissioning of response indicator 2.00 Nos. 583.00

113 E-113 Supply, installation, testing & Commissioning Fire Exit Signage boards with 3hrs battery backup 2.00 Nos. 6,247.00

114 E-114 Supply & laying of 2 Core X 1.5 sq.mm. FRLS Armoured PVC Insulated copper cable 500.00 Meter 186.00

115 E-115 Supply & laying of 4 Core X 1.5 sq.mm. FRLS Armoured PVC Insulated copper cable 50.00 Meter 255.00

SR. No. Description of Work Unit Rate Amount

Supply, Installation, Testing & Commissioning of Network TDN IR Mini Dome Camera, 1/2.9" CMOS,

MP @ 25fps, Triple stream, Min. Illumination required 0.25 lux @ color, WDR 120dB, Min. Pixels 2560 x

1920, Shutter Speed 1/30000 - 1/5; Adavance Video Compression technology such as H.265 / H.264 /

MJPEG, 3mm~8mm, MFZ lens, HLC, 3DNR, Minimum Edge Intelligence Video Analytics: Motion

Detection, Camera Tampering, Intrusion/Object enter area; 4 nos Privacy Mask, Smart IR with upto 30m IR

distance, AES-128/256, PCI Data Security Standard compliance, 128GB SD card support, DC12V, PoE

(IEEE 802.3af) (Class 2), IP 66, IK10, Having Operating temp range : –10°C to 50° C. Certifications:

ONVIF Profile S, G compliant, UL, CE/EN, FCC Part 15 & RoHS compliant along with mounting brackets

suitable for Cieling / Wall mounting & required accesories as per site requirement.

Supply, Installation, Testing & Commissioning of 5MP IP Network TDN IR Bullet Camera, 1/2.8" CMOS,

5 MP @ 25fps, Triple stream, Min. Illumination required 0.05 lux @ F1.4 (color), WDR>120dB, Min.

Pixels 2560 x 1920, Shutter Speed 1/30000 - 1/30; Adavance Video Compression technology such as H.265

HEVC / H.264 / MJPEG, Smart Codec, 2.7-13.5 mm 5X motorized focus & zoom lens, P-IRIS, HLC,

3DNR, Minimum Edge Intelligence Video Analytics: Motion Detection, Video Tampering, Intrusion, Loiter,

Line crossing, Unattended object, Missing object, Face detection; 5 nos Privacy Mask, 4 IR LEDs Smart IR

with upto 60m IR distance, Stream encryption, AES-128/256, PCI Data Security Standard compliance, FIPS

Chipset Built-In, 256GB SD card support with SD card encryption, Dual channel Audio G.711a / G.711 Mu

/ G.726, Alarm: 2 In/ 1out, In-built Heater; PoE+ (802.3 at) and 12V DC/24V AV; IP 66 / IP 67 / NEMA

4X, IK10, Having Operating temp range : –40°C to 60° C. Certifications: ONVIF Profile S, G compliant,

UL, CE (EN 50130-4 & EN 55032) , FCC Part 15 & RoHS compliant along with mounting Brackets

suitable for Pole / Wall mounting & required accesories.

SITC of 32 Channel NVR having features smart H.265+/H.265/ Smart H.264/H2.64/MJPEG, Max

118 E-118 Mbps incoming Bandingwidth, support min 2 SATA HDDs Slot - each slot supporting min 8TB, Up to 12 1.00 Nos. 64,975.00

MO Resolution for Preview and Playback and with 8 TB Survellance Hard Disk

Supply, Installation, testing and commissioning of Intel Core i5 12C Processor 25M Cache, up to 4.90 GHz

119 E-119 / 16GB DDR5 / 512 SSD / Win 10 Pro Operating System / No Monitor / DVD RW / 3 Yrs NBD / PS 1.00 Nos. 75,900.00

500W/ NVIDIA T600 4 GB GDDR6 Workstation Graphics Card including 4 mDP to DP adapters

SITC of 32 Inch 500 NTS Brightness professional Display with Direct-Type LED, Viewing Angle :

Degree Verti, 178 Degree Hor. Operation 27x7, Native Resolution 3840 x 2160 (16:9) - UHD, 4 x USB (2

120 E-120 x 2.0, 1 x 2.0 internal, 1 x Type C), 0-40°C, ≤0.5 W, HTML 5 Browser Opera(4.9), Yes(internal) IEEE 1.00 Nos. 50,000.00

802.11 a/b/g/n Dual

WiFi certificated, BIS, YES CLASS A 3dB margin. (Including Five year free maintenance with guarantee)

SR. No. Description of Work Unit Rate Amount

Networking Enclosures & Accessories Supply, Installation, Testing & Com mission ingot 24U Wall mount

121 E-121 closed rack with front glass door, fan tray on top, perforated rear doors, keyboard tray with shelf. Casters & 2 1.00 Nos. 51,316.00

nos vertical power strip with std etc as required.

Supply, Installation, Testing And Commissioning of Layer 2 Managed Gigabit POE switch with 24 #

10/100/1000BaseT ports and 2 # Gigabit Combo ports(RJ45/SFP), 2 # Gigabit SFP Port.

Supplying & erecting approved make LAN cable of following size in existing pipe as per direction

124 E-124 Supply and laying of Cat-6 STP LSZH UV outdoor cable in PVC conduit with termination as per TIA 250.00 Meter 113.00

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured / metallic/white front plate , modules erected with necessary

connections as per site situation directed by Engineer In charge.

(4) TV Co-axial Socket outlet

Supplying and erecting approved make online Un-interruptible Power Supply system comprising flat cum-

boost charger with IGBT base rectifier & Inverter & sealed maintenance free SMF batteries. The charger

having operating capacity for input 160-270V AC & inverter having output 230V,50 Hz Ac with 0.8 load

power factor with battery, over/under voltage output with over load & short circuit protection equipment. The

system housed in CRC sheet duly powder coated paint with following power backup.with MS painted

batteries stand, 10% Overload capacity for momentary load.

(D) 5 KVA with 1Hr Backup

Supplying & erecting carbon dioxide (CO2) fire extinguisher user of following capacity with necessary

127 E-127 clamps made from 50 x 6 mm M.S. Flat with nut & bolts grouted in wall complete. 2.00 Nos. 6,526.00

For 4.5 Kg Capacity, including maintaining/ renewal validity of all Co2 fire extinguisers up to the

completion of O&M period

128 E-128 Supplying & Erecting automatic emergency light with maintenance free battery for 20 watts tube. 2.00 Nos. 3,900.00

Supplying rubber matting of following thickness as per IS : 15652/IEC61111

Providing and erecting metallic vitrified danger notice board for MEDIUM VOLTAGE installation to be

erected as per IS.

Providing printed instruction chart both in English and Gujarati and duly framed with front glasses, for

treatment of person suffering from Electric shock

Providing & laying. Double walled corrugated pipes (DWC) of polyethylene (conforming to IS 14930 II)

Anti Rodent type with necessary connecting accessories of same material at required depth for laying of

132 E-132 cable. below ground / road surface for enclosing cable and backfilling the same to make ground as per 500.00 Meter 62.00

SR. No. Description of Work Unit Rate Amount

Providing & erecting water cooler having storage capacity 150 Ltr. & cooling capacity 150 Ltr.per hour @

an ambient temp of 45˚ C. The outlet temp. of the water should drop by 15˚C within a hour, The water cooler

should be comprising of hermetically sealed compressor, fan motor, condensing unit, water tank surrounded

by evaporating, coil, thermostats, relay etc.complete with necessary inlet & outlet connection. The body of

water cooler will be made from Stainless Steel.

Supplying and erecting water filter cum purifier with ultra violate technology. (Aquaguard / waterdoc model

or equivalent symphony/ crystal/videocon model)

S.I.T.C. of single phase submersible pump set suitable for 100 mm size or more dia bore well having motor

capacity and discharge as under with necessary panel box. Lifting and Lowering taken extra.

(c) Motor rating 2 HP (17 stage) pump having capacity of 106 LPM at 40 mtr head suitable for 32 mm dia.

Supplying & erecting approved make Automatic liquid level controller 6A. with sensor testing as per

138 E-138 instruction of Engineer in charge on site complete with wiring connection with existing wires , with copper 1.00 Nos. 2,332.00

conductor from pump to upper and lower tank.

Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible Submersible copper cable

139 E-139 approved make of following Size. 20.00 Meter 103.00

(B) 3 Core x 2.5 Sq. mm.

AIR-CONDITIONERS

Providing and erecting approved make split air-conditioning unit consisting of copper condensing unit with

fan motor, hermetically sealed rotary compressor with accessories etc. duly connected separately erected

evaporating unit and blower motor with its accessories by means of extra supplied proper insulated copper

140 E-140 tubing,drain PVC pipes suitable for ( cost includes powder coated Stand, Eco Friendly green gas charging, 2.00 Nos. 51,923.00

15A plug top & Remote Control) with necessary core cutting.

(1)For ISEER Range (KWH/KWH)(3.1 to 3.99) Premium Category

(b) for 1.5 ton capacity

Premium Category : O-General, Mistsubishi Electric

Providing and erecting Inverter based approved make Cassette type split air-conditioning unit consisting of

condensing unit with fan motor, hermetically sealed scroll/rotary compressor with accessories etc. duly

141 E-141 connected separately erected evaporating unit and blower motor with its accessories by Eco friendly Green 6.00 Nos. 79,932.00

gas charging & Internal copper wiring & Remote control with necessary core cutting.

(B) for 2 ton capacity

SR. No. Description of Work Unit Rate Amount

Providing and erecting approved make Cassette type split air-conditioning unit consisting of condensing unit

with fan motor, hermetically sealed scroll/rotary compressor with accessories etc. duly connected separately

142 E-142 erected evaporating unit and blower motor with its accessories by Eco friendly Green gas charging & Internal 1.00 Nos. 1,59,619.00

copper wiring & Remote control with necessary core cutting.

(D) for 4 ton capacity- 1/3Phase

Supplying & installing MS standard type stand mounting for outdoor unit of Split A.C. upto 4 TR capacity

erected with necessary hardware materials as directed.

Supplying and erecting insulated pair of soft copper tubing open or concealed including power and control

cable,necessary PVC drain pipes for Split AC machine up to 4 TR capacity

Rigid UPVC drain pipe of 10 Kg/cm2. rating with 9 mm thick.nitrile rubber insulation.

Rigid UPVC drain pipe of 10 Kg/cm2. rating with 9 mm thick.nitrile rubber insulation.

Rigid UPVC drain pipe of 10 Kg/cm2. rating with 9 mm thick.nitrile rubber insulation.

Liason / Follow UP with Supply Co.

Filling the necessary application to supply co. following up and getting the supply filling the necessary test

report to the supply co. inclusive. All official fees including security deposits will be paid by the client and

out of pocket expenses shall be of contractor.

SR. No. Description of Work Unit Rate Amount

Machine room Less LIFT

Supplying, Erecting, Testing & Commissioning the passenger / stretcher lift having following main

[1] GEAR LESS LIFT DRIVE comprising of High Starting torque Lift duty 3 phase 440 V A. C. Permanent

magnetic synchronous motor of proper rating with high efficiency shall be used.

[2] Micro processor based / PLC, ACVVF, vector control drive with encoder feedback closed loop system

shall be used for lift car and door operation which shall be full collective selective operation hall call demand

response, UP/DOWN hall stops, Main, Up/ Down Contactor with overload and phase reversal relay and

safety controls.

149 E-149 [3] Car with M S platform with bracings of adequate size and to sustain the impact load cabin + passenger 2.00 Nos. 13,47,854.00

with safety factor of fire for steel and side panels of Stainless steel of sheet of grade 304 duty. Car ceiling

will be S.S. finishes with aesthetic appearance with LED ceiling lights. Car flooring shall be of anti skid

PVC with choice of colour of engineer in charge. Car doors shall be of stainless steel grade 304, hairline

finish with centre opening / telescopic automatic doors. Car panel will also be S.S. 304 finished with

emergency stop device, mechanical door safety device, facility of auto/ attended mode. All car panel buttons

and all floor switches must be with brail language as per lift act.

[4] All landing doors shall be fully automatic centre opening/ telescopic opening made of hairline finish steel

grade of 304 with key holes and infrared curtains with Unlocking facility from outside.

[5] Appropriate battery operated emergency light in the car along with alarm switch shall be provided.

[6] Digital scrolling indicator system for up-down arrow along with floor position indicator shall be provided

inside the car and at all floors.

[7] Full height infra red curtain with multiple criss / crossing light beams shall be provided.

[8] Automatic Rescue Device (ARD) shall be provided accordingly of passenger capacity.

[9] Audio visual indication in the lift car showing over loading shall be provided such that doors kept open

till excess load is removed.

SR. No. Description of Work Unit Rate Amount

[10] Spring buffers/PU Buffers shall be provided.

[11] Car fan with automatic sleep timer shall be provided.

[12] Voice annunciater with suitable music shall be provided in lift car.

[13] Self diagnostics system for operational and safety parameters shall be provided in control panel.

[14] Mechanical over speed governor, door key holes in the floor doors, fireman switch shall be provided.

[15] Lift machine hoisting arrangement in the lift machine room and monkey ladder for lift pit should be

provided by the lift agency, along with the other steel structure works, foundations for the machine etc…

[16] In the hoist way fascia plate shall be provided without any extra cost, where ever required as / if directed

by engineer in charge.

[17] Permanent wiring in lift machine room and lift well with proper numbers of light points, with fixtures,

exhaust fan and plug points shall be provided by the agency. Power supply of 3 phase 440 V shall be made

available by department in lift machine room.

[18] Any civil/ electrical works for additional and alteration in lift shaft and machine room related to erection

of lift shall be made by lift agency without any extra cost.(granite/marble fixing around all landing door

openings are not in lift agency’s scope.)

[19] Agency has to provide all working drawings and documents and liaison services for obtaining all

necessary permission from lift inspector and other authorities.

[20] As per statutory requirement of Got. Of Gujarat lift & escalator act 2000, lift

[20A] As per statutory requirement of Govt. Of Gujarat lift & escalator act 2000, lift agency has to provide

1. Car top safety barricade

2. Push & talk communication system.

3. Fireman's switch operation at Ground Floor.

4.carrying out third party lift inspection during/after lift erection and provide report by third party

authorized by concern licensing authority 5.agency has to provide third party insurance upto completion of

free maintenance period and submit the document for the same.

[21] Car Panel Operating Buttons with floor position indicator/buttons must be of Auto Glow type clearly

visible when view from inside cabin.

[22] For Physically Handicapped person Full Length Handrails of hairline finish steel grade of 304 should be

provided at appropriate height on the Rear & Side Wall Panels in Lift Car.

SR. No. Description of Work Unit Rate Amount

agency has to provide

1. Car top safety barricade

2. Push & talk communication system.

3. Fireman's switch operation at Ground Floor

Note: 1 - Advanced control system dual 32bit embedded microprocessor with CANBUS Serial

Communication mode including Regenerative power efficient operation on site programming facility,Anti

nuisance,Pre-opening,BMS/RMS system supporting hardware & Software.

2. Floor indication LCD Display with call registration & brail mark with arrival gong and hall lantern &

TFT Screen in the car with MP3 Voice Announcer.

3. CAR PANEL should be scratch resistive SS Moonrock finish for car and all Doors, All landing doors

must have fire rating up to 1 hours and car door must have multi-level crisscross beam door protection.

4. To & Fro communication system & wiring (i.e. car, control room, guard room)

8 / 10 Passengers, Ground plus 1 upper floor with Rated Speed of 1.0 m/sec.,

(C) With General PLUS ADDITIONAL SPECIAL FEATURES attached herewith. Prem. Cat.

Total Cost of Electrical work & ELV Work

Ahmedabad Municipal Corporation

Proposed Construction of New Gymnasium, Library and Physiotherapy Center at TP - 35, FP – 42 (Social Infrastructure Purpose) in Chandlodiya

Plot of North West Zone, Ahmedabad Municipal Corporation.

BOQ for Fire Fighting Work

Sr.No. Item Description Quantity Unit Rate Amount

(A) Fire Pump Room Acce. (Positive Suction).

Supplying, Installation, Testing and commissioning of electric driven main fire pump suitable for automatic operation and

consisting of following: Horizontal type, centrifugal End Suction pump of cast iron body & bronze impeller, mechanical seal

1.0 to ensure a minimum pressure of 3.5 kg / sq.cm. at highest and farthest outlet at specified flow of 137m3/Hour@70M . head 2.00 Nos. 2,77,500.00

conforming to IS 1520. The pump shall be coupled to TEFC motor of suitable HP & speed and complete set shall mounted

on common base frame with, coupling, coupling guard, foundation bolts etc. as required. (Hydrant & Sprinkler System)

Supplying, Installation, Testing and commissioning of Diesel Engine driven fire pump suitable for automatic operation and

consisting of following: Horizontal type, centrifugal End Suction pump of cast iron body & bronze impeller , mechanical

2.0 seal to ensure a minimum pressure of 3.5 kg / sq.cm. at highest and farthest outlet at specified flow of 137m3/Hour@70M 1.00 Nos. 5,94,006.00

head conforming to IS 1520.The pump shall be coupled to TEFC motor of suitable HP & speed and complete set shall

mounted on common base frame with, coupling, coupling guard, foundation bolts etc. as required

Supplying, Installation, Testing and commissioning of Jockey Pump 10.8M3/[email protected] Centrifugal End

4.0 Suction. he pump shall be coupled to TEFC motor of suitable HP & speed and complete set shall mounted on common base 2.00 Nos. 1,08,000.00

frame with coupling, coupling guard, foundation bolts etc. as required. (Hydrant & Sprinkler System)

Supplying, Installation, Testing and commissioning of cubical type floor mounted power cum control panel complete with

5.0 suitable switch gear, bus bars, relays, contractors, indicating lamps, fuses, instruments manual isolator & auxillary switch 1.00 Nos. 2,55,000.00

including connections complete as required.

Providing, fixing, testing and commissioning below Cable for Fire Pumps

(Only from Panel to Pumps)

6.1 3 C X 35 Sqmm Alluminium Armoured 60.00 Meter 417.00

6.2 3 C X 16 Sqmm Alluminium Armoured 60.00 Meter 252.00

6.3 2 C X 1.5 Sqmm Copper Armoured. 150.00 Meter 143.00

6.4 Cable Tray 300X50 mm. 20.00 Meter 735.00

6.5 Cable Tray 150X50 mm. 20.00 Meter 510.00

Providing, fixing, testing and commissioning of Pressure Gauge with cock & accessories for pumps.The pressure gauge

7.0 shall be approved type. The Gauges with cock shall be constructed of die cast aluminium & stove enameled. The Gauge shall 7.00 Nos. 4,050.00

be of stainless steel bourden type.

Providing, fixing, testing and commissioning of Pressure switches of diaphram operated SPDT type whether IP66 suitable

range (15 kg/cm² to 5 kg/cm²) for pump sets with Ball valves, Fittings like unions / collars / reducers etc.

Sr.No. Item Description Quantity Unit Rate Amount

Providing, fixing, testing and commissioning Air vessel fabricated from

PumpMS plate Acce.

Room with dished ends,dia

(Positive of 350 mm

and height 1500 mm with suitable supporting legs, outside painted with one coat of primer and two coats of synthetic

9.0 enamel paint of approved shade, complete with one 25mm dia connection from pump delivery, one 25 mm drain with 2.00 Nos. 48,000.00

valve.The air vessel shall be tested to 1.5 times of working pressure. Complete as per technical specification & drawing

Providing, fixing, testing & commissioning of C.I.Butterfly valve conforming to IS:13095 class PN 16 rating with Fittings,

Flanges, Nutbolts, Washers, Gaskets etc.of size:

10.6 25mm dia.Ball Valve. 4.00 Nos. 1,427.00

10.7 15mm dia Ball Valve. 12.00 Nos. 749.00

Providing, fixing, testing and commissioning of C.I. Dual plate type Non-Return Valve class PN 16 rating with fittings,

flanges, nutbolts, washers, gaskets etc.of sizes:

Providing, fixing, testing and commissioning of Above Ground MS. ERW Black C Class Heavyduty pipes as per IS:

(upto 150 mm dia.) and IS: 3589 (upto 200 mm dia. And above) including cutting, screwing, welding etc. and providing all

fittings like flanges, bends, tees, elbows, reducers, clamps, hangers etc. with painting of one coat of primer and 2 or more

coats of synthetic enamel paint of approved make / shade complete as per specification.

12.6 25mm dia. 12.00 Meter 595.00

13.0 Providing and fixing, testing and commissioning of "Y" Type Strainer

(B) Fire Hydrant System & Acce.

Providing, fixing, testing and commissioning of Above Ground MS. ERW Black C Class Heavyduty pipes as per IS:

(upto 150 mm dia.) and IS: 3589 (upto 200 mm dia. And above) including cutting, screwing, welding etc. and providing all

fittings like flanges, bends, tees, elbows, reducers, clamps, hangers etc. with painting of one coat of primer and 2 or more

coats of synthetic enamel paint of approved make / shade complete as per specification.

Sr.No. Item Description Quantity Unit Rate Amount

14.3 80mm dia. Fire Pump Room Acce. (Positive Suction). 24.00 Meter 1,943.00

Providing, fixing, testing and commissioning of Under Ground M.S. ERW Black C Class Heavyduty pipes as per IS:

15.0 1239 (upto 150 mm dia.) and IS: 3589 (upto 200 mm dia. And above) with IWL/pypecoat, 4mm thickness wrapping and

coating and providing all fittings like flanges, tees, elbow, fasteners with all required.

Providing, fixing, testing & commissioning of C.I.Butterfly valve conforming to I.S:13095 class PN 16 rating with

Fittings, Flanges, Nutbolts, Washers, Gaskets etc.of size:

Providing, fixing, testing and commissioning of C.I. Dual plate type Non-Return Valve class PN 16 rating with fittings,

flanges, nutbolts, washers, gaskets etc.of sizes:

18.0 Fire Fighting Equipement

Providing, fixing, testing and commissioning of SS Single Headed Oblique Pattern Hydrant Landing Valves as per IS:

5290 with 80 mm dia flanged inlet & 63 mm dia female outlet complete with cap and chain etc.

Providing, fixing, testing and commissioning of SS Branch Pipe with nozzle of 20 mm nominal bore outlet suitable to fit

with standard instanteneous type 63 mm dia coupling. As per IS:903.

Providing, fixing, testing and commissioning of 63 mm dia 15m long RRL Hose Pipe with 63 mm dia.Type A Male and

female Stainless Steel couplings duly binded with GI wire, rivets etc. conforming to IS 636 as required.

Providing, fixing, testing and commissioning of weather proof standard fire Hose Cabinet wall mounting type 18 Guage.

(750 x 600 x 250) having Double Opening with M.S. fabricated stand, necessary locking arrangement by allan key.

Providing, fixing, testing and commissioning of Wall mounting swing type first aid Fire Hose Reel with drum, hanging

18.5 bracket, 36 M x 25 mm dia high pressure hose reel tubing as per IS:884 with shut nozzle and ball valve and all required 13.00 Nos. 8,873.00

Providing, fixing, testing and commissioning of 25 mm dia Air Release Valve and Ball Valve assembly on top of each riser

for Air release system.

Providing, fixing, testing and commissioning of CI Four way Fire Brigade Inlet as per IS: 904 having 63 mm dia inlet with

150 mm dia Butterfly valve blank cap and chain with necessary fittings, flanges, nutbolts etc.

Providing, fixing, testing and commissioning of CI Two way Fire Brigade Inlet as per IS: 904 having 63 mm dia inlet with

18.8 blank cap and chain with 100 mm dia Butterfly valve necessary fittings, flanges, nutbolts, gasket and all required 1.00 Nos. 10,719.00

Sr.No. Item Description Quantity Unit Rate Amount

(C) FireAutomatic

Pump Room Acce.

Sprinkler Suction).

Providing, fixing, testing and commissioning of Above Ground MS. ERW Black C Class Heavyduty pipes as per IS:

(upto 150 mm dia.) and IS: 3589 (upto 200 mm dia. And above) including cutting, screwing, welding etc. and providing all

fittings like flanges, bends, tees, elbows, reducers, clamps, hangers etc. with painting of one coat of primer and 2 or more

coats of synthetic enamel paint of approved make / shade complete as per specification.

Providing, fixing, testing and commissioning of Under Ground M.S. ERW Black C Class Heavyduty pipes as per IS:

20.0 1239 (upto 150 mm dia.) and IS: 3589 (upto 200 mm dia. And above) with IWL/pypecoat, 4mm thickness wrapping and

coating and providing all fittings like flanges, tees, elbow, fasteners with all required.

Providing, fixing, testing & commissioning of C.I.Butterfly valve conforming to IS:13095 class PN 16 rating with Fittings,

Flanges, Nutbolts, Washers, Gaskets etc.of size:

(D) Sprinkler System Equipements.

Providing, fixing, testing and commissioning of Sprinkler Alarm valve of cast iron body and brass/bronze working parts

comprising of water motor alarm, bronze seat clapper, and clapper arm, hydraulically driven mechanical gong bell to sound

22.0 continuous alarm when the sprinkler system activates, pressure guages, emergancy releases, strainer, pressure switch, cock 1.00 Nos. 67,875.00

valve complete with drain valve and bypass, test control box, ball valves, flanges, gasket etc.

of size 150 mm dia.

Providing and fixing, testing and commissioning of K 5.6 Pendent type Standard response Sprinkler rating of 68 deg.C.

with required accessories.

Providing, fixing, testing and commissioning K 5.6 Upright Sprinkler Standard response rating of 68 deg.C . with

required accessories.

Providing and fixing, testing and commissioning of K 5.6 Side Wall type Standard response Sprinkler rating of 68 deg.C.

with required accessories.

Providing, fixing, testing and commissioning of SS Flexible drops 1200mm Long.Unbraided , Maximumm Service

26.0 pressure 175PSI,.Sprinkler Flexible Drop system is a ready to use assembly to fit sprinkler heads in desired location in a 230.00 Nos. 1,056.00

suspended ceiling. It easily positions the sprinkler in center of the ceiling tile at a correct height.

Sr.No. Item Description Quantity Unit Rate Amount

Providing, fixing, testing and commissioning of Flow Indicating Switch Pump

fittings, Acce.

Flanges, (Positive

nut-bolts, Suction).

washers etc. as per

requirement of sizes. 150MM .

Providing, fixing, testing and commissioning of Annunciator panel for flow control switch, providing Audio/Visual

28.0 indicating of actuation of automatic sprinkler system for each zone complete as per specifications with provision for 12 zones 1.00 Nos. 17,250.00

'Indication of zone fire, 'Indication of zone fault, 'Fire/Fault hooter, 'Alarm cancel for fire/fault, 'Battery for emergency

Supplying, Installation, Testing and commissioning of 2 C X 1.5 Sqmm Copper Armoured for Flow Switch Cabling from

Announciation panel to Flow Switch.

Providing and fixing, testing and commissioning of Drainning & Testing Assembly 25mm dia with by pass valve, drain

connection & Sight Glass as required.

(E) Fire Extinguishers

Providing & fixing of ABC 6 Kg Fire Extinguisher Mono Ammonium Phosphate Powder 50, Stored Pressure Type,

Pressure Gauge, Controllable discharge mechanism Class A Rating 3A & Class B rating 21B as per IS

Providing and fixing, testing and commissioning of CO2 type Fire Extinguisher of capacity 4.5 kg filled with Co2 Gas as

32.0 per IS 15222 with controll discharge mechanis, fitted with Hose & Horn applicable on Class B fire rating 21B confirms to IS 18.00 Nos. 5,270.00

15683 bearing ISI mark. Co2 cylinder as per IS 7285 .

Providing and fixing, testing and commissioning of Higher capacity Trolley mounted ABC Dry Chemical; Powder type (

33.0 MAP - 90% ) Fire Extinguisher of capacity 25 kg. confirms to IS 10658, bearing ISI mark, ( Outside Co2 Cylinder 1 Kgs. 5.00 Nos. 8,276.00

Providing and fixing, testing and commissioning of CO2 type Fire Extinguisher of capacity 22.5 kg filled with Co2 Gas as

34.0 per IS 15222 with controll discharge mechanism fitted with Hose, Horn & TROLLEY confirms to IS 2878 bearing ISI 5.00 Nos. 19,050.00

mark. Co2 Cylinder as per IS 7285 .

Providing and fixing, testing and commissioning of Higher capacity Trolley mounted Mechanical Foam type Fire

Extinguisher of Capacity 50 liter confirms to IS 13386, bearing ISI mark, (Quoted For 45 ltr)

36.0 Providing, fixing, testing and commissioning of below Auto Glow Signages.

36.2 Fire Hydrant 4” X 12” 4.00 Nos. 438.00

36.3 Fire Lift 4” X 12” 4.00 Nos. 438.00

36.4 In Case of Fire do not use Lift ,Use Staircase 8"x 8" 4.00 Nos. 534.00

36.5 Fire Extinguisher 8"x 8" 21.00 Nos. 534.00

36.6 Fire Pump Room 12"X 6" 1.00 Nos. 582.00

37.0 Civil Work. (In Client Scope)

37.1 Providing, fixing, testing and commissioning Hume Pipe NP2 class 400mm dia. 40.00 Meter 1,419.00

37.2 valve camber. 1M X 1M X 1M. 2.00 Nos. 1,05,000.00

37.3 Excavation & Backfilling Of Soft And Hard soil. 120.00 Cum 750.00

38.0 Supply, Installaton of Structure Steel Support 1,500.00 Kg 124.00

APPROVAL FIRE SYSTEM FROM LOCAL FIRE AUTHORITY

39.0 Getting of Fire Fighting System Approval from local fire authority with all other charges and documentations for getting No 1.00 Job 2,50,000.00

Objection Certificate (NOC, FSPA/Opinion).

Sr.No. Item Description Quantity Unit Rate Amount

Fire Rated steel doors with steel frames as per BS:476 (20&22),Fire Pump

(Part-2) forAcce. (Positive

stability Suction).

and integrity. pressed

Galvanized steel conforming to IS 277 with the following specification. recommended fire door shell have doors tested at

CBRI for maximum rating of 120 Minutes.

Door frame shall be Single rebate profile of size 105 x 57 mm made out of 1.60mm (16gauge) minimum thick galvanized

steel sheet. Frames shall be mitered and field assembled with self-tabs. All provision should be mortised, drilled and tapped

for receiving appropriate hardware. Rubber door silencers should be provided on the striking jamb. Frames should be

provided with back plate bracket and anchor fasteners for installation on a finished plastered masonry wall opening. Once

frame installed should be grouted with cement & sand slurry necessary for fire doors on the clear masonry opening.

40.0 Door leaf shall be 46mm thick fully flush double skin door. Door leaf shall be manufactured from 1.2mm (18guage) 25.20 Sqm 33,000.00

minimum thick galvanized steel sheet. The internal construction of the door should be rigid reinforcement pads for receiving

appropriate hardware. The infill material shall be resin bonded honeycomb core. All doors shall be factory prepped for

receiving appropriate hardware and provided with necessary reinforcement for hinges, locks, and door closers. The edges

should be interlocked with a bending radius of 1.4mm. For pair of doors astragals has to be provided on the meeting stile for

both active and inactive leaf. Vision lite wherever applicable should be provided as per manufacturer's recommendation with

a beading and screws from inside. The glass should be 6mm clear borosilicate fire rated glass of relevant rating of the door.

All doors and frames shall be finished with polyurethane aliphatic grade paint of approved color. The door leaf and frame

shall have passed minimum 250 hours of salt spray test. Rate should include supply and installation of door and hardware

set as mentioned in the door. Hardware Fittings Make :- Doorma , Geze , Hafales

Total Amount of Fire Fighting Work

Total Amount of Fire Fighting Work