Development of Eco Trail at Ekta Nagar, Dis.-Narmada

Sr No QTY Unit Total Rate Amount

Clearing and grubbing road land including uprooting rank vegetation grass bushes,shrubs,sapling and trees

1 girth up to 300 mm removal of stumps of trees cut earlier and disposal of unserviceable materials (B) By 0.605678 Hectare 1,15,016.68

manual in area of thorny jungle

Clearing and grubbing road land including uprooting rank vegetation grass bushes,shrubs,sapling and trees

2 girth up to 300 mm removal of stumps of trees cut earlier and disposal of unserviceable materials(D) By 0.1 hectare 34,889.38

mechanical means in area of thorny jungle

Earthwork in cutting including preparing the slope and camber andstacking or utilising the cutting stuff in

3 bank as directed upto 200 Meters from the end of cutting with all lead and lift.(iii) Hard rock 17.03 Cu.M. 694.28

Earthwork in cutting including preparing the slope and camber andstacking or utilising the cutting stuff in

4 bank as directed upto 200 Meters from the end of cutting with all lead and lift.(ii) Soft rock not requiring 3300 Cu.M. 321.49

Earthwork for embankment including breaking clods, dressing with all lead and lift (excluding watering and

5 consolidation)(E) From Borrow area within 3.0 Km. lead 3300 Cu.M. 173.3100

Over and above Item No Extra for lead and lift upto 100m height, 10% rise for each floor - total 30 floors for

100m height, (300% rise on rate for lead and lift)

Add extra over item 6 for conveying and utilising the stuff in bank from end of cutting with all required lead

7 and lift.(C) Above 400 Meters upto 500 Meters 3300 SQM 129.28

Excavation for foundation upto 1.5 m depth including sorting out and stacking of useful materials and

8 disposing off the excavated stuff upto 50 Meter lead.(D) Soft rock not requiring Blasting 219.88 Cu.M. 545.59

Excavation for foundation upto 1.5 m depth including sorting out and stacking of useful materials and

9 disposing off the excavated stuff upto 50 Meter lead.(E) Hard Rock

Excavation for foundation upto 1.5 m depth including sorting out and stacking of useful materials and

10 disposing off the excavated stuff upto 50 Meter lead.(C) Hard Murrum

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not

exceeding 20 cm. in depth consolidating each deposited layer by ramming and watering.

ramming and consolidating etc. complete.

Providing and laying cement concrete 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20m.m.

13 nominal size) and curring complete excluding cost of form work in : (a) Foundation and Plinth - PCC. 29.51 Cu.M. 3,591.22

Providing and laying cement concrete 1:3:6 (1 Cement : 3- Coarse sand : 6- graded stone aggregates 20 mm

nominal size) and curing complete including cost of formwork in (A) Foundation and Plinth

Provinding and Laying controlled cement concrete M-250 including finising smooth with curing complete

15 including the cost of form work but excluding the cost of reinforcement for reinforced concrete work in 25.15 Cu.M. 4,261.20

foundations, footings, base of columns and mass concrete.

Provinding and Laying controlled cement concrete M-250 including finising smooth with curing complete

16 including the cost of form work but excluding the cost of reinforcement for reinforced concrete work in 1.58 Cu.M. 7,772.23

columns up to plinth and Column having any cross sectional area

Provinding and Laying controlled cement concrete M-200 including finising smooth with curing complete

17 including the cost of form work but excluding the cost of reinforcement for reinforced concrete work in 4.08 Cu.M. 4,302.28

foundations, footings, base of columns and mass concrete.

Provinding and Laying controlled cement concrete M-200 including finising smooth with curing complete

18 including the cost of form work but excluding the cost of reinforcement for reinforced concrete work in Wall 9.88 Cu.M. 6,932.64

up to plinth.

Providing and laying controlled cement concrete M-200 and curing complete including the cost of formwork

19 and excluding the cost of reinforcement for reinforced concrete work in slabs 4 Cu.M. 6,808.12

Providing and laying controlled cement concrete M.250 and curing complete excluding the cost of formwork

and reinforcement for reinforced concrete work in Grid Slab.

Providing and casting in situ ordinary cement concrete M-150 for coping, over riding returns including

formwork curing and finishing complete.

Brick work using common burnt clay building bricks having crushing strength not less than 35 kg./Sq.Cm. in

22 foundation and plinth in Cement Mortar 1:5. (1-Cement : 5 -fine sand) (B) Conventional 11.5236 Cu.M. 4,310.73

Brick work using common burnt clay building bricks having crushing strength not less than 35 kg./Sq.Cm. in

23 foundation and plinth in Cement Mortar 1:5. (1- Cement : 5 -fine sand)(A) Modular….Extra for brick work in 31.48 Cu.M. 4,717.31

superstructure above floor two level Item No. 1(6.12) (A) Modular

(i) Half brick masonry in common brunt clay building bricks having crushing strength not less than

24 Kg/Sq.Cm. in Cement mortar 1:4 (1- Cement : 4 -coarse sand ) in foundation and plinth (A) Modular 9 SQM 631.39

Providing and laying brick on edge flooring laid dry grouted with c.M. 1:6 (1 - Cement : 6 - coarse sand)

25 including finishing the joints flush curing etc. complete

Coursed rubble masonry with hard stone of approved quality in foundations and plinth in Cement Mortar 1:6

(1-Cement : 6-coarse sand) etc. complete.

Providing and fixing in position roof slab using Stone Slab 100mm thickness. Including lifting, placing in

position, joining amd sealing the joints using cement mortar 1:3, in proper line, level and slope etc..

completed with all material, labour, tools, tackles and equipments, as per drawing and as directed by the

Engineer in charge

Steel work, welded in built up sections framed work including cutting, hoisting, fixing in position and applying

a priming coat of red lead paint. (A)In beams and joists, channels angles Tees, flats, with connecting plates or

28 34.31205 Quintel 9,108.48

angle cleats as in main and cross beams. Hip and jack rafters, purlins conneted to common rafters and the

like - ISMB.

Steel work / Tubular section, welded in built up sections framed work including cutting, hoisting, fixing in

position and applying a priming coat of read lead paint. (A)In beams and joists, channels angles Tees, flats,

29 with connecting plates or angle cleats as in main and cross beams. Hip and jack rafters, purlins conneted to 11063.24 Kg 139.14

common rafters and the like, with two coats on new steel and other metal surface with enamel paint,

brushing, interior to give an even shade including cleaning the surface an even shade including cleaning the

surface of all dirt, dust and other foreign matter.

Providing and laying polished Kota stone slab flooring over 20mm (Average) thick base of cement mortar 1:6

(1-cement : 6-coarse sand) or L.M. 1.1.5 (1-Lime putty : 1.5 - coarse sand) laid over and jointed with grey

cement slurry mixed with pigment to match the shade of slab including rubbing and polishing etc. complete.

(A) 25mm thick

Providing and fixing Rajula stone 75mm thick 60mm x 45mm size including fixing in cement mortar as

Providing leather finish to Kota stone surface by mechanical brushing process to create a textured, anti-skid

32 matte surface, including surface preparation, brushing, cleaning, and finishing complete as per specifications. 39 SQM 60.60

Providing and fixing 35 mm thick shutters for Doors, windows and clerestory windows including Indian teak

wood frames 10 cm x 7 cm. size including anodized alluminium fixtures and fastenings including primer coat

of approved quality and two coats of oil painting etc, complete. (ii) Fully Panelled.

34 including the cost of wooden beadings of first class teakwood and necessary cutting of glass. (1) 5 mm thick. 1.92 Sq.M. 1,195.64

Providing and applying weather coat (hydrophobic coating) on exposed brick masonry as a protective layer to

shield masonry from the ailments due to weathering effects like afflorations and discoloration, offering water

repellency and durability and should be transperent sealant for a natural finish. Approved brand KRISREPELL

M&G it is is single pack solvent based yet tin free mixture of silane, siloxane & fluoropolymer. This

composition provides easy to clean protection against water, oil or dirt without change of surface

appearance as well it does not affect vapor permeability and keeps it's natural touch of low to high

porous natural stones e.g. marble, travertine, granite, unglazed ceramic tiles etc.

Providing and laying polished kota stone slab 25mm thick in risers of steps,skirting Dedo and pillars laid on

10mm thick cement mortar 1:3 (1-Cement : 3 coarse sand) and jointed with gray cement slury mixed with

pigment to match the shade of slab including rubbing and polishing etc. complete. For door and window

Providing and laying controlled cement concrete M.250 exposed work with curing etc. complete including the

37 cost of formwork but excluding the cost of reinforcement for R.C.C. work in (B) COLUMNS:(i) Having cross- 0.9891 Cu.m 14,664.80

sectional area 0.05 to 0.08 Sq.M

Providing formwork of ordinary timber planking so as to give a rough finish including centering shuttering

strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding

M. and removal of the same for in situ reinforced concrete and plain concrete work in. (G) Columns

PillarsPosts and struts. (2)Circular or curved in Plan.

Providing TMT Bar FE 550D reinforcement for R.C.C. work including bending, binding and placing in position

39 complete upto floor two level

Providing TMT Bar FE 500D reinforcement for R.C.C. work including bending, binding and placing in

40 position complete upto floor two level. For Up to f.f 6180.22 Kg 77.29

Providing 15mm thick cement plaster in single coat on Rough (Similar) side of single or half brick walls for

interior plastering and finished even and smooth in (ii) Cement mortar 1:4 (1-cement :4-sand), including

fixing 150 mm wide chicken mess jali at every RCC and Brickwork joints including labour and material etc.

complete as directed by engineer in-charge.

20mm thick sand faced cement plaster on walls upto height 10 metres above ground level consisting of

42 12mm thick backing coat of C.M. 1:3 (1-cement : 3-sand) and 8mm thick finishing coat of C.M. 1:1 (1-cement : 65.098 SQM 353.98

1-sand) etc. complete.

Providing and laying cement concrete flooring 1:2:4 (1-cement : 2-coarse sand : 4-graded stone aggregate

20mm nominal size) laid in one layer, 40 mm thick and finished with a floating coat of neat cement including

43 mixing water proofing materials in cement mortar in proportion recommended by the manufacturer as

approved and directed by engineer in-charge.

Providing and constructing natural stone step pathway in hilly terrain, including all required works such as

excavation, foundation preparation, PCC bed, stone masonry steps, and finishing, complete as per approved

drawings and directions of the Engineer-in-Charge.The work shall include:- Excavation in soft rock along the

pathway alignment to the required depth and width for formation of steps, including dressing of sides,

trimming of slopes, and disposal of excavated material within lead of 50 m.- Providing and laying Plain

Cement Concrete (PCC) 1:2:4 of thickness 100 mm as leveling course and foundation bed below stone steps,

including mixing, placing, compacting, and curing.-Construction of stone steps using approved natural

44 random rubble / sandstone blocks in cement mortar 1:4, forming treads and risers of required size, including 1800 Cu.M. 1,347.34

dressing of exposed faces, proper alignment, leveling, and jointing.

- Filling and compacting earth behind steps where necessary to achieve proper support and stability. finishing

of joints, and cleaning of the pathway.-Carriage of materials, including loading, unloading, transportation,

stacking, tools and plants, labour, and all incidental charges required to complete the work.- The finished

pathway shall have stone steps approximately 500 mm tread and 150 mm riser, maintaining proper slope and

alignment suitable for pedestrian movement in eco-trail areas.

Providing and constructing random rubble stone retaining wall along the stepped eco-trail pathway using

hard locally available natural stones of approved quality and size, laid in random rubble masonry with proper

interlocking and hearting stones to form a stable retaining structure supporting the pathway edge.- The work

shall include excavation for foundation in all types of soil, dressing and leveling of the base, providing hand-

packed stone soling and PCC 1:2:4 (if required) as foundation bed, and constructing the retaining wall using

Proper through stones/bond stones shall be provided at regular intervals to ensure structural stability.- The

wall shall be constructed with a base width of approximately 600–900 mm and top width of 300–450 mm,

45 maintaining a slight batter towards the hill side to improve stability. The exposed face of the wall shall be 1200 RMT 3,125.95

neatly arranged with well-packed joints, and all voids shall be filled with smaller stones and spalls.- The work

shall also include providing gravel backfill behind the wall, compaction in layers, and installation of weep

holes at 1.0–1.5 m spacing to allow drainage of water and reduce hydrostatic pressure. The top course shall

item includes all materials, labor, tools, transportation of stones, dressing, laying, jointing, curing (if mortar

masonry), scaffolding, and all incidental works required to complete the retaining wall as per approved

drawings and site conditions.

Extra over item No. 7.17 for superstructure above plinth level upto floor two level (for coursed rubble Per

masonary in stone step and wall). floor

Extra for additional lift in superstructure above floor two level (for coursed rubble masonary in stone step

and wall). floor

Providing and laying broken china mosaic flooring for terrace using 12 mm to 20 mm broken pieces of glazed

tiles to be laid over cement mortar 1:3 to plain or slope and to be tempered to bring mortar creme out upto

surface using white cement including rounding off junctions and extending them upto 15 cm along the

wall,clearing with water and oxalic acid etc. as directed.

Providing and Fixing Terracota Jali with all tools and tackel with material, labour, loading, unloading, shifting

etc Complete As directed by the Architect and Engineer In Charge. For All Floor and Level with all tool,

tackels, material, labour, lead, lift, necessary scaffolding and cleaning the site after completion of job.

Providing and fixing Subway Tiles - Bevelled Glossy Finish in perfect line, level and plumb for Toilet Dedo

50 with all material, labours, tools, tackels etc.. Complete as per drawing and as directed by Engineer in charge. 109.2 SQM 1,055.45

Providing, fixing and construction of sandwich type 18 mm thick One Side polished Granite Stone of uniform

size and colour for kitchen/pantry/countr/ laboratory, sink shelves etc. in floor, dedo or facia upto 100 mm

wide including necessary cement mortar bedding in cement mortar 1:2 of required thickness. Granite Stone

51 shall be fixed over 25 mm thick Polished Kota bottom, cement joints and pointing as specified with necessary 1.92 Sq.M. 6,046.87

making of edges, polishing curing daily mopping with water and kerosene as directed for atleast 15 days or

upto the satisfaction of engineer-in-charge.

Providing and fixing counter top wash basin 550 mm x 400 mm size of first grade, white in colour with single

hole for pillar trap with CI or MS brackets painted with including cutting holes and making good the same

including providng and fixing CP brass waste coupline 32mm dia including providng and fixing MI washer

52 uinon 32 mm dia, including providng and fixing 15mm dia pillar tap capsten head screw down high pressure 4 Each 2,318.30

with screws, shanks and back nuts, including providing and fixing waste pipe 15mm x 600 mm pvc inlet

connection 15mm brass screw down stop tap with necessary fititngs etc. complete

Providing and fixing wash Down water closet (European type, W.C. Pan with integral 'P' or 'S' trap including

jointing the trap with soil pipe in cement mortar 1:1 (1 cement : 1fine sand) and G.I. inlet connection for flush

53 pipe with W.C. pan with Providing and fixing plastic seat and cover for wash down water closet with C.P. 4 Each 2,318.30

Brass hinges and rubber buffers etc... complete as approved and as directed by Engineer In charge

Providing and fixing Urinal of approved quality including conecting the Urinal with waste pipe , tap etc.

complete. (A) White earthenware flat back or corner type size 430mm x 260mm x 350mm.

Providing and Fixing Health Fauset Heavy duty with hook with fitting with all tools and tackel with material,

55 labour, loading, unloading, shifting etc Complete As directed by the Architect and Engineer In Charge...Jaquar 4 Each 843.95

and Equivalent

Providing and chromium plated Pillar cock 20 mm Heavy duty swan neck with all tools and tackel with

56 material, labour, loading, unloading, shifting etc Complete As directed by the Architect and Engineer In 4 Each 843.95

Charge...Jaquar and Equivalent

Providing and Fixing chromium plated Bib cock 15 mm Heavy duty with cap with all tools and tackel with

57 material, labour, loading, unloading, shifting etc Complete As directed by the Architect and Engineer In 4 Each 580.84

Charge...Jaquar and Equivalent

Providing and Fixing Metropole flush valve with all tools and tackel with material, labour, loading, unloading,

58 shifting etc Complete As directed by the Architect and Engineer In Charge...Jaquar and Equivalent 4 Each 580.84

Preparing structural design of RCC Under Ground / Partially under ground / above high ground level Reservoir

of required capacity as per relevant I.S. standards and constructing the same, including excavation in all types

of soil strata (including rock) including shoring strutting if required, for loose soil / to protect from collapse,

casting 100 mm thick P.C.C. levelling course in M- 15, Refilling the pit with proper soil and disposing of the

surplus stuff at all lead. Including cement plaster in CM 1:2 with approved water proofing compound to all

over inside container (i.e. walls, base, top slab/dome bottom etc. all). Including all types of labour and

material charges of lowering, laying, erecting / hosting and jointing of pipe assembly to inlet, outlet overflow,

washout and bye pass arrangement as per hydraulic design. Providing and fixing accessories, CI Manhole

frame and cover, water level indicator, adequate cowl type ventilators or lantern type ventilator with

stainless steel jail. RCC chambers for valves. Providing and applying three coats of cement paint / snowcem to

the out side face of structure. It also includes satisfactory water tightness test as per relevant I.S. code and

painting name of scheme and capacity on the tank as per direction of engineer in charge. List of Indian

Standards for Design of GSR / SUMP The structural design of GSR shall be in accordance with provisions

relevant I.S standards (1) I.S. 3370 part I & II 2009 or Its latest revision(1.1) I.S. 3370 part III & IV 1965 or Its

latest revision (2) I.S. 456 – 2000 or Its latest revision.(3) I.S. 1893 – 2000 – 1984 or Its latest revision.(4) I.S.

875, Part – 1 to 3, 1987 or Its latest revision.

Cost of 20,000 litre at 5.44 rs per litre GWSSB SOR ITEM 2A section 1C 2 Each 109888.00

3 Phase Borewell Submersible Pump Sets (Rates exclusive of GST).Electric motor driven borewell submersible

60 pump set confirming to IS 8034 and motor confirming to IS 9283 working at 3 phase 400 / 440 volt 50 Hz AC 2 NOS 29582.90

supply & 2900 RPM. 12.5 HP

Single phase borewell submersible pump motor set MOC: Casing: CI-FG260, Impeller: Bronze & Shaft: SS:410

61 (Rates exclusive of GST) 3 HP

Control Panel Board (Rates exclusive of GST).DOL / Star Delta starter suitable for local & remote pump

control application consisting of MPCB, overload relay and contactors as per Type II coordination including

control accessories.S. D. from 11 to 15 HP

Control Panel Board (Rates exclusive of GST).DOL / Star Delta starter suitable for local & remote pump

control application consisting of MPCB, overload relay and contactors as per Type II coordination including

control accessories.D. O. L. up to 3 HP

PVC insulated flat / round submersible copper cables (Rates exclusive of GST).PVC insulated flat submersible

64 cable as per detailed technical specifications of R/C of GWSSB conforming to IS 694, IEC 60227 / 60228.1 R x 3 1000 RMT 313.10

Providing and supplying in standard length IS! mark high density Polyethylene H.D.P.E. Pipes suitable for

potable water as per IS specification no, 4984/1995 including all local and central taxes, transportation,

freight charges, octroi, inspection charges, loading, unloading, conveyance to the dept. stores etc. comp.

KG/CM^2. 63 mm dia

Providing laying and jointing in true line and level 50mm dia. U.P.V.C. Pipe (SCH- 80) for cold water including

fittings make PRINCE / SUPREME / ASTRAL / FINOLEX as approved by Engineer In Charge. Pipe shall be fixed

66 on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including 2100 RMT 359.37

necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including

cost of all materials.

Providing laying and jointing in true line and level 32mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including

fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe

67 shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concealed as directed 50 RMT 119.15

including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent,

including cost of all materials.

Providing laying and jointing in true line and level 25mm dia. U.P.V.C. Pipe (SCH- 40) for cold water including

fittings make PRINCE / UPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe

68 shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concealed as directed 160 RMT 91.84

including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent,

including cost of all materials

Providing laying and jointing in true line and level 15mm dia. U.P.V.C. Pipe (SCH- 40) for cold water including

fittings make PRINCE / UPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer In Charge. Pipe

69 shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concealed as directed 160 RMT 72.65

including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent,

including cost of all materials

Providing and fixing 600mm x 450mm bevelled edge glass mirror of superior glass mounted on 6mm thick

70 A.C. sheet or plywood sheet & fixed to wooden plugs with C.P. brass screws and washers. 4 Each 859.41

71 Providing and fixing Both side double S.S Soapdisc fixing on wall with wall plug etc. completed. 4 Each 411.17

Providing, laying and jointing in true line and level 75 diametre U.P.V.C (Type B) conforming to IS 13592-1992

with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of

approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant,

72 pipe shall be fixed on wall using of PVC clamp of the size 75 mm diametre x 149 mm length x 145 mm heigh at 30 RMT 241.19

every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as

bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost

of all materials.

Providing, laying and jointing in true line and level 110 diametre U.P.V.C (Type B) conforming to IS 13592-

1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of

approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant,

73 pipe shall be fixed on wall using of PVC clamp of the size 100 mm diametre x 149 mm length x 145 mm heigh 50 RMT 387.45

at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such

as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including

cost of all materials.

74 Providing and fixing PVC SWR Vent Cowl 75 mm dia as directed by engineer in charge 10 Each 291.00

75 Providing and fixing PVC SWR Vent Cowl 110 mm dia as directed by engineer in charge 12 Each 301.27

Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with bricks having

crushing strength not less than 35Kg./Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x 610mm

internal dimensions total weight of cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt.

of frame 15Kg. ) (R.C.C. top slab with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone aggregate 20mm

size) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth with a

floating coat of neat cement on walls and bed concrete etc. complete.(ii) Inside dimensions 500mm x

mm and 450mm deep for pipe line with one or two inlets. (more than 10 ton)

Providing, erecting and fixing double coated Syntex or equivalent PVC (ISI) mark water tank of required

77 capacity each with all necessary fittings & connection etc. complete on terrace. 40000 litre 3.95

Providing and fixing ball valve in water tank heavy type 50mm dia. including fitting, testing etc. complete.

79 Providing and fixing Gun metal check or nonreturn full way wheel valve.(E) 40mm dia. 6 Each 663.43

Providing and fixing pre-cast concrete kerb stone of gray cement based concrete block 30cm length, 30cm

height and 15cm thick of M250 grade concret as per approved design and including excavation for fixing in

proper line and level, filling the joint with C:M 1:3 (1cement : 3fine sand) etc complete.

Providing and fixing CNC Cut metal letters with paint finish etc. Complete for the Eco trail entry gate as per

81 design by EIC. The work should be completed in all the aspects. Including the cost of 2 JOB 10100

material,labour,machinaries etc.

Providing and applying wood texture powder coating finish on fabricated mild steel gate structure including

vertical posts, arch beam and associated steel members, comprising surface preparation by degreasing, sand

82 blasting or mechanical cleaning, application of epoxy/zinc rich primer, base powder coating layer and heat 12.24 SQM 505

transfer wood grain film finish, followed by curing in oven at 180–200°C to achieve durable natural wood

appearance.

Providing and fixing C.I. Cover with frame of size 455mm x 610mm etc. complete as directed by engineer in-

Providing and fixing cast iron steps of size 500mm x 150mm x 22.5mm and painting with two coats of Anti-

84 corrosive paint etc. complete.

(B) Providing sock pit of 5.00 Cu.M. Volume including excavating and filling brickbats with dry masonry work

85 at top for 45cm. height including covering the top with stone including providing vatas in C.M. 1:3 with 12 Each 3486.88

finishing curing etc. complete as directed.

Providing and installing prefabricated Bio-Toilet unit of approved design and specifications consisting of GI

With ACP Sheet / prefabricated superstructure with door and locking arrangement, ventilation system, solar

panel with LED lighting, vent pipe for gas outlet, ceramic / FRP toilet pan with flushing arrangement,Sink,

86 water storage tank 1000 liter Capacity, bio-digester tank with Soak pit both are 2000 liter capacity and 2 Each 330000

bacterial treatment technology for decomposition of human waste, including base platform, plumbing

connections, fittings, transportation, labour, installation and commissioning complete in all respect as

directed by the Engineer-in-charge.

Interpretive Information Display Panel (Fiber Cement Board) Providing and fixing interpretive information

display panels fabricated from 12 mm thick exterior grade Fiber Cement Board, cut to required size and

finished with mineral matte sand textured coating suitable for outdoor landscape installations. The panel

shall have engraved typography with paint-filled lettering in earth brown colour, suitable for interpretive

content such as zone information and sculpture descriptions. The edges of the panel shall be finished with

87 mm thick corten steel inset frame strip to provide protection and a natural weathered aesthetic compatible 24.32 SQM 6544.33

with the eco-trail landscape. The panel shall be mounted on MS support frame or structural base using

stainless steel fasteners, including necessary cutting, engraving, finishing, fixing and alignment. The work shall

include panel fabrication, engraving, paint filling, surface finishing, corten frame strip, fixing accessories and

installation, complete in all respects as per approved drawings and direction of Engineer-in-Charge.

Providing and supplying mechnically double twisted highly galvanized with (PVC) Poly Chloride coating

gabions made of mesh size 10 x 12 mm woven wire as per ASTHMA 10 x 12 mm woven wire as per ASTHMA

975 -97 , size of gabion 1 m x 1 m x 1 m including providing and laying stones in the gabions and arranging

them in a required manner in the section of break water or such other structure including quarrying , blasting

, loading at quarry site transporting at work site and arranging in the gabion in workman like manner with

required layer thickness and arranging this gabions in required layers with the crane if required capacity (if

required as per drawings or as directed ) with all material , labour , tools etc. comp.

Providing and constructing circular stone seating with thatch roof canopy for eco-trail resting point,

consisting of circular coursed rubble masonry seating in cement mortar 1:6, finished with 40–50 mm thick

Kota stone top seating, including excavation for foundation, PCC bed, and construction of masonry base. The

structure shall include a centrally fixed 100 mm dia MS pipe column embedded in PCC foundation block with

89 base plate and anchor bolts. The roof shall consist of bamboo rafters and purlins forming a conical 7 NOS 29249.6

framework fixed to the MS pipe and covered with natural grass thatch of 150–200 mm thickness including

binding with GI wire. The item includes all materials, labour, scaffolding, transportation, curing and finishing

complete as per drawings and direction of Engineer-in-Charge.

Providing and Fixing Onduline tile of Size 1.07 meter x 0.4 meter of shaded red colour with Onduline ridge of

90 size 0.9 m x 0.42 m, speedy screws including all taxes,transportation etc. complete as per Engineer-in-charge) 282.6 SQM 2121

Providing and fixing PUF Insulated continueous sandwich panels for walls of total thickness not less than

mm and width 1.0 m made out from continue line method on automatic plant.Panel shall have 0.5 mm thick

pre coated GI sheet on both side of Polyurethane Foam confirming to IS 12436:1988.The Precoated sheet

shall be of minimum 240 mpa steel grade confirming to IS 14246:1995 and shall have zinc coating of

minimum 120 gsm as per IS:277:1992 , 5-7 microns epoxy primer on both side of the sheet and polyester top

91 coat 15-18 micron.The PPGI Sheet shall have plastic protective guard film of minimum 25 microns to avoid 86.55 SQM 3118.04

scratches during trasportation.The panels shall be vertically joined together by tongue and groove joints. The

PU Foam shall be self extinguishing, fire retardant type having minimum density of 40 Kg/Cu.mt.( +, - 2 Kgs)

including 0.25 mm thick craft paper edging on both edges. The panels shall be fixed to the steel frame

structure with minimum 5mm thick self tapping GI screws of required length and nos. with minimum spacing

Providing and fixing of Bottom and top U track for closing of end joints for

cut PUF panels of size of 52mm x 30mm with 5mm lipping on Both edges.

The U track shall be made out of 0.5 mm thick pre coated GI sheet.The

Precoated sheet shall be of minimum 240 mpa steel grade confirming to IS

14246:1995 and shall have zinc coating of minimum 120 gsm as per

92 IS:277:1992 , 5-7 microns epoxy primer on both side of the sheet and 31.4 RMT 582.95

polyester top coat 15-18 micron. The PPGI Sheet shall have plastic

protective guard film of minimum 25 microns to avoid scratches during

transportation. The U track shall be fixed with suitable POP rivet with wall

roof panels and plinth with Expandable fastners with minimum spacing of

450 mm c/c. The Utrack shall be fixed

Masonary work using Aerated light weight concrete block having crushing strength not less than 35 kg/sqcm

93 for super structure above plinth level upto floor two level in cement mortar 1:5 ( 1 cement : 5 fine sand ) 4.19 Cum 4600

complete as per Technical Specification

A MS (Mild Steel) metal locker cabinet of size 8 feet in height, with a width of approximately 3 to 3.5 feet and

a depth of around 1.5 to 2 feet. It features (09) y 3 to 3.5 reet and a depth of around 1.5 to 2 feet. It features

(09) nine individual locker compartments arranged in a 3×3 grid, each equipped with ventilation slots, a

handle, and a padlock. The cabinet is finished in a gray green color and has various colored labels for

identification. The cupboard includes a 3- in a point locking mechanism with a heavy -duty lock and chrome -

94 plated or powder coated handle for security. Finishedvy dutylock and chrome -plated or powder- with an 2 NOS 25553

epoxy polyester powder coating after thorough surface treatment (degreasing, derusting, and phosphating),

it is available dstorconga

in standard grey or beige colours. Ideal for offices, schools, and industrial settings the MS cupboard conforms

to IS :513 and IS:101 standards, ensuring strength, reliability, and long service life

TOUGHNED GLASS:- Providing and fixing 10mm thick toughned glass pivot door with all necessary hardware,

95 floor spring etc complete. 21.2 SQM 5501.8

shoulder Mounted Way Finder on Diamond Grade

retro- reflective sheeting size – 3’ x 3’

Providing and Laying shot blasted non interlocking ,paver blocks 80 mm thick M-45 grade of specified

thickness, size, grade of concrete and colour machine made and blasting by automatic shot blasting machine

and high density of as per approved sample of approved make for footpath, parking areas, service lanes,

cross over and other areas as mentioned in the drawing. Including providing and laying 50 to 80 mm thick

average bedding layer of coarse sand below paver block as per required grading and specification. Laid paver

block shall be mechanically compacted. The work of the paving blocks shall be executed in line and level by

97 skilled mason of flooring work only. Small size of paver block with same specifications shall be used at residu 200 SQM 1084.11

or at end. It should be laid in such a way that the no cutting of the paver block to be necessary. If cutting of

paver block shall be required, than cut by machine only and laying to be done by skilled flooring mason. The

Finished surface of the paver block shall have coarse sand texture finish. Paver blocks shall be compacted and

shall be relaid if necessary. Actual laid area shall be measured and paid without any wastage.A) 80mm thick

M-45 grade Paver block of size 200mm x 200mm and 200 x 100.(As per direction of Engineer In-

Charge/Architect)

Point wiring in Copper (Modular)Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of

pipe to be erected concealed in/ on surface on wall/ceiling complete with 6A Modular type switch / bell push

98 & accessories and earth continuity of following type, erected on PVC / Metallic box, single mounting base 30 pt 481

frame covered with textured/metallic front plate modules erected on / in wall / ceiling as per pipe erected,

with necessary Lamp holder/ceiling rose / H.D.Connector as directed.(f) with medium class Rigid PVC pipe

and accessories erected concealed in wall/ceiling complete Cat. III

Point wiring for secondary light point with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (green) both are of ISI

marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected

concealed in / flushed on wall/ceiling, complete with earth continuity and necessary connection with

99 primary light with accessories erected on Metal / PVC box covered with 3 mm thick PC(Polycarbonet) / 20 pt 166

Acrylic sheet for open / concealed wiring. with necessary Lamp holder / ceiling rose / H.D.Connector as

directed.Note:- Maximum up to 6 mtrs length, excess will be considered as Mains for Secondary Point. (f)

with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete Cat. III

Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of .ISI marked 1.1 KV

Grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be erected concealed in /

flushed on wall/ceiling complete with 6A Modular type switch and hum free EME four or more step type

100 electronic fan regulator with separately mounted and accessories with earth continuity of following type 6 pt 668

erected on PVC / Metallic box, single mounting base frame covered with textured/metallic front plate

modules erected on / in wall / ceiling as per pipe erected. with necessary ceiling rose / H.D.Connector as

directed(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade

FRLS PVC insulated multi strand copper wires up to 10 mtr length, in below type of pipe erected complete

with Modular type switch & 5 pin Plug erected on PVC / Metallic/Wooden box covered with appropriate

101 front plate modules erected on / in wall / ceiling as per pipe erected with following type of accessories.--[I] 6 pt 505

For 6A Plug and 6 a switch with 2-1.5 sq.mm Cu. Wire from nearby switchboard/mcb db board--(f) with

medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling complete. Cat. III

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade

FRLS PVC insulated multi strand copper wires up to 10 mtr length, in below type of pipe erected complete

with Modular type switch & 5 pin Plug erected on PVC / Metallic/Wooden box covered with appropriate

102 front plate modules erected on / in wall / ceiling as per pipe erected with following type of accessories.--[II] 8 pt 738

For 16A Plug and 16 amp switch with 2-2.5 sq.mm Cu. Wire from mcb db board.--(f) with medium class Rigid

PVC pipe and accessories erected concealed in wall/ceiling complete. CAT III

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade

FRLS PVC insulated multi strand copper wires up to 10 mtr length, in below type of pipe erected complete

with Modular type switch & 5 pin Plug erected on PVC / Metallic/Wooden box covered with appropriate

103 front plate modules erected on / in wall / ceiling as per pipe erected with following type of accessories.--[III] 4 pt 863

For 16A Plug and 16 amp switch with 2-4 sq.mm Cu. Wire with 2.5 sq.mm ( green) earthing wire from mcb d

b board.--(f) with medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling

complete.Cat. III

Point wiring for Looped Plug with 6A Modular type switch & 5 pin socket erected on PVC / Metallic box,

single mounting base frame covered with textured / metallic front plate modules erected on / in wall /

ceiling with following type accessories.--Single mounting base-frame & Textured / Metallic front plates.

Point wiring for Two Way Controlled Light Point with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (green) both

are of .ISI marked 1.1 KV grade FRLS PVC insulated multistrand copper wires, in following type of pipe to be

erected concealed in / flushed on wall/ceiling ,complete with 6A Modular type switches and following type of

105 accessories erected on PVC / Metallic box, single mounting base frame covered with textured / metallic front 4 pt 598

plate modules erected on / in wall / ceiling as per pipe erected. with necessary batten/angle holder or ceiling

rose or H.D.Connector as directed.--(f) with medium class Rigid PVC pipe and accessories erected concealed

in wall/ceiling complete--Cat-III

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured / metallic/white front plate , modules erected with necessary

connections as per site situation directed by Engineer In charge.--(4) TV Co-axial Socket outlet --Cat.III

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured / metallic/white front plate , modules erected with necessary

connections as per site situation directed by Engineer In charge. (3) Two Pin/RJ-11 Telephone Socket [A] For

One Gang Cat-III

Providing following type of Modular Type Accessories mounted with pvc / metallic box, single mounting base

108 frame covered with textured / metallic front plate , modules erected with necessary connection. As desired 5 Each 25

by Engineer In charge(7) Blank Plate Single Cat-III

Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured / metallic/white front plate , modules erected with necessary

connections as per site situation directed by Engineer In charge.(8) Computer RJ-45 socket . cat-lll

Providing & erecting Switch board for Computer or electric apparatus consisting of following modular type

accessories mounted with PVC / Metallic concealed/open box with single mounting base frame covered

110 with textured/metallic /white front plate,modules erected with necessary connections as directed--1 no. 6 Each 1122

6A/16A universal plug-switch combined.--3 nos.6A Switch--3 nos. 6A 5 pin Plug

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected on/in

wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps

with following dia of pipes, in approved manner as directed--b) 25 mm

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be erected on/in

wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with adhesive solution & Clamps

with following dia of pipes, in approved manner as directed--d) 40 mm

Providing & erecting PVC Corrugated Flexible Conduit with required nos. of coupling, PVC bushes, Check-nuts

etc. complete of following sizes. (2) 25 mm

(A) Supplying and laying UPVC cable trunking system comprising unplasticised polyvinyl, chloride rigid

114 material with ignition free & flame proof confirming BS .All necessary accessories and measuring of following 50 mtr 275

sizes. (1) 75 mm x 50 mm trunking

(A) Supplying and laying UPVC cable trunking system comprising unplasticised polyvinyl, chloride rigid

115 material with ignition free & flame proof confirming BS .All necessary accessories and measuring of following 100 mtr 187

sizes. (3) 50 mm x 50 mm trunking

Mains & Wires--Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in

following type of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor

116 FRLS PVC insulated stranded wire of green colour for earth continuity of following size (general wiring + in 450 mtr 62

street light) --(a) with medium class Rigid PVC pipe and accessories--(a) 2 wire 1.5 sq. mm

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of

pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC

117 insulated stranded wire of green colour for earth continuity of following size (general wiring + in street light) 500 mtr 82

(a) with medium class Rigid PVC pipe and accessories(b) 2 wire 2.5 sq. mm (FRLS)

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of

pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire

of green colour for earth continuity of following size (FRLS) (a) with medium class Rigid PVC pipe and

accessories (a) 2 wire 4 sq. mm

Supplying & erecting XLPE(IS:7098)(I)-88 ISI armoured copper cable 1.1 KV grade to be erected as directed of

following size.(E) 3 core 2.5 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand / Solid Copper conductor for

120 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of 50 mtr 505

following size of cables..(B) 4 core 6 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand / Solid Copper conductor for

121 KV. to be laid on wall with necessary clamps or in existing trench / pipe at road crossing or floor of 200 mtr 361

following size of cables.(A) 4 core 4 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV.

122 to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables (C) 3 1/2 500 mtr 282

core 50 Sq. mm ( 25 Sq.1/2 mm core)

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV.

123 to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables (c) 4 core 10 10 mtr 139

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured

124 cable complete with out going tails, insulating tape etc for following size of cables. (c) 2 to 4 core 10 Sq. mm 10 Each 38

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured

125 cable complete with out going tails, insulating tape etc for following size of cables. (B) 2 to 4 core 6 Sq. mm 10 Each 38

Providing and, fixing heavy duty flange type brass double compression type cable gland with rubber ring for

126 PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of 10 Each 75

cables.(B) 3 & 1/2 core 35/50 Sq. mm

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for PVC insulated armoured

127 cable complete with out going tails, insulating tape etc for following size of cables. (A) 2 to 4 core 2.5 / 4 Sq. 10 Each 33

Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped

128 with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an 10 Each 20

approved manner. (D) 35/50 Sq.mm. . (ISI MARKED) LUGS

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped

129 with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an 5 Each 13

approved manner. (B) 10 Sq.mm

Solder less crimping type Copper lugs conforming to IS suitable for cable of following size evenly crimped

130 with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an 25 Each 8

approved manner. (A) 1.5/2.5 to 6 Sq.mm

Making trench in soft soil of suitable width of 90 cms deep for laying cable or locating the fault all over the

run and backfilling the same and making the surface as normal ground.

Making trench in Hard Murrum / Tar Road of suitable width of 90 cm or required depth for laying any size of

132 cable or locating the fault all over the run and back filling the same and making the surface as normal 500 mtr 74.00

Providing & laying approved make Double walled corrugated pipes (DWC) of polyethylene(conforming to IS

14930 II )with necessary connecting accessories of same material at required depth for laying of cable.

below ground / road surface for enclosing cable and back filling the same to make ground as per original.

(A)50 mm dia

Providing & laying approved make Double walled corrugated pipes (DWC) of polyethylene(conforming to IS

14930 II )with necessary connecting accessories of same material at required depth for laying of cable.

below ground / road surface for enclosing cable and back filling the same to make ground as per original.

(C)90 mm dia

SECTION 3.00 SWITCHGEARS & DISTRIBUTION BOARDSMINIATURE CIRCUIT BREAKERS.Miniature circuit

breaker single pole 6A to 25A suitable to operate on 240 V A.C. system and having breaking capacity 10 KA to

be erected in existing box. confirming to IS 8828/1996 with ISI Mark(QTY FOR MCB OF DB AND MCB OF

PANEL) Cat-III

Plastic enclosure fitted with DIN rail suitable for incorporating Three /Four nos. MCB

137 Sheets steel powder coated enclosure suitable for incorporating One/Two nos. MCB 2 Each 175

Providing and erecting Approved make Three pole moulded case circuit breaker having breaking capacity ICU

of 25 K.A. at 415 V having normal current rating up to 25 A to 100A. with Fixed thermal & magnetic release

138 suitable to work on A.C. supply 50 c/s. with all internal connections, spreader tinned copper & complete 2 Each 5302

erected in existing 16 G.M.S. housing.ICS=100% of ICU only Cat III

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted

with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to

139 house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) suitable for 1 Each 3379

(B) three phase incoming and single phase horizontal type outgoing Per phase isolation type (PPI) (b) sheet

steel double door (iii)8 way

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted

with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to

140 house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) suitable for 1 Each 2885

(B) three phase incoming and single phase horizontal type outgoing Per phase isolation type (PPI) (b) sheet

steel double door(ii)6 way

Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted

with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to

141 house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) suitable for 1 Each 3836

(B) three phase incoming and single phase horizontal type outgoing Per phase isolation type (PPI) (b) sheet

steel double door (iv)12 way

Providing and erecting Sheet Steel powder coated Vertical MCB distribution board (VTPN) - flush / surface

mounted double door (IP54) fitted with insulated copper busbar, isolated neutral link, earth bar and DIN rail,

142 confirming to IS 13032 and BS 5486-1986,IP-54 suitable for 63/100 AMP TPN MCCB + RCCB as incomer and 1 Each 18480

three phase outgoing as per following .(The DBs should be used of same company of MCB to be used) (D)12

way outgoing

EARTH LEAKAGE CIRCUIT BREAKERS.Approved make ELCBs / RCCBs conforming to IS: 12640 and having

sensitivity of 30 mA and Short Circuit withstand capacity of 6 KA and suitable for operation on single phase

143 240 V. having characteristic of quick action & tripping with all advance feature & do not incorporate any 7 Each 2213

electronic component.for following Max. rating erected as directed Cat-III (ii) 40Amps. DP

Approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and Short Circuit

withstand capacity of 6 KA and suitable for operation on single phase 240 V. having characteristic of quick

action & tripping with all advance feature & do not incorporate any electronic component.for following Max.

rating erected as directed (i) 25 Amps.DP Cat-III

Providing and erecting Approved make RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and

Short Circuit withstand capacity of 10 KA and suitable for operation on 3 phase and neutral 415V,50Hz.

145 having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic 1 Each 3010

component for following Max. rating erected as directed.(iii) 63 Amps. FP Cat. III

Providing and erecting Approved make Four pole moulded case circuit breaker having breaking capacity ICU

of 25 KA. at 415 V,having normal current rating up to 25 A to 100A. with Microprocessor release suitable to

work on A.C. supply 50 c/s. with all internal connections, spreader tinned copper & complete erected in

G.M.S. housing. (rate will be includding of supply and erecting of encloser.) ICS=100% of ICU only Cat III

146 Note:-1 Add Rs. 10% extra for housing/Encloser of MCCB for Item No 3-4-1 to 3-4-12 (The Enclosures should 1 Each 8862.4

be used of same company of MCCBs to be used) *Add 35% additional for microprocessor type of mccb in

place of conventional for item no.3-4-1(here we added 10% for Enclosere and 35% for Microprocessor of

MCCB in basic rate of 3-4-1.)

Providing and erecting Approved make Earth fault Relay suitable to mount with inter connection suitable to

following size of moulded case circuit breaker having CT ratio & MCCB rating as following along with shunt

trip 220V AC. with all internal connections & complete erected in existing M.S.housing.. (1) 15 A -100 A , CT

Ratio 1/100

Providing and fixing approved make Perforated C type cable tray. Made from pre- galvanized sheet steel.

The cable tray should be bended as per IS 2062/1079 . with max 17.5% perforation with coupler plate / Fish

148 plate and GI hardware like nut - bolt and washers etc. erected on existing support as per Specification and as

per instruction of engineer in charge..

(3) 150 X 50 X 1.5 mm Thick 20 mtr 319

Providing and erecting Approved make RCCBs conforming to IS: 12640 and having sensitivity of 30 mA and

Short Circuit withstand capacity of 10 KA and suitable for operation on 3 phase and neutral 415V,50Hz.

149 having characteristic of quick action & tripping with all advance feature & do not incorporate any electronic 1 each 4272

component for following Max. rating erected as directed.(iv) 100 Amps. FP (100 mA Sensitivity) Cat. III

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming to IS: 513/CRCA/

aluminium die cast powder coated and high U.V. & corrosion resistance with diffuser with company

mark/name 160V to 270V, Power Factor more than 0.9, THD < 15%,CCT 3000 K to 6500K, Luminaire efficacy>

150 85 lumens/watt ,LED LED driver efficiency > 85 %( fitting required LM-79 & LM-80 Certificates)(NOTE: Below 20 nos 370

wattage capacity between the ranges shown.) (A) Tube Light with integral driver (iv) 22-24 Watts, Surge -

2KV,IP-20, conventional 4 feet Cat-lll

Supplying and erecting led lamps with following wattage capacity of 220 to 240 voltage, minimum

burning hours life, 500 V in built-surge protection,Polycarbonate diffuser, mounting suitable for E14 / E27 /

B22 lamp holders, pf >= 0.5(A) LED Lamps integral type, with PC diffuser suitable LAMP holder (iii) 10 to

watts Cat-III

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder coated and high U.V. & corrosion resistance with diffuser

housed in aluminium casted body with company mark/name 160V to 270V,Power Factor more than 0.95,

152 THD < 15 %,CCT 3000 K to 6500K, Luminaire efficacy> 85 lumens/watt ,LED driver efficiency > 85 %( fitting 18 each 584

required LM-79 & LM-80 Certificates)(NOTE: Below description have shown ranges of Wattage capacity of

shaped Surface/Recessed Mount Downlight with provision for spring loaded mounting clips complete.IP20(iii)

16-20 watts, Surge-2 KV. Cat-lll

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder coated and high U.V. & corrosion resistance with diffuser

housed in aluminium casted body with company mark/name 160V to 270V,Power Factor more than 0.95,

153 THD < 15 %,CCT 3000 K to 6500K, Luminaire efficacy> 85 lumens/watt ,LED driver efficiency > 85 %( fitting 5 each 751

required LM-79 & LM-80 Certificates)(NOTE: Below description have shown ranges of Wattage capacity of

Circular shaped Surface/Recessed Mount Downlight with provision for spring loaded mounting clips

complete.IP20(iv) 22-24 watts, Surge-2 KV Cat-lll

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder coated and high U.V. & corrosion resistance with diffuser

housed in aluminium casted body with company mark/name 160V to 270V,Power Factor more than 0.95,

154 THD < 15 %,CCT 3000 K to 6500K, Luminaire efficacy> 85 lumens/watt ,LED driver efficiency > 85 %( fitting 20 each 1777

required LM-79 & LM-80 Certificates)(NOTE: Below description have shown ranges of Wattage capacity of

Circular shaped Surface/Recessed Mount Downlight with provision for spring loaded mounting clips

complete.IP20(vi) 36-40 watts, Surge-2 KV Cat-lll

Supply of approved make frp/grp pole having followiing specifications :FRP/GRP pole made by centrifugal

moulding process using thermoset resin polyester/epoxy resin system having minimum glass content

45.0%.The pole should be in one pieceand tapered round in shape,having smooth outside surface finish and

should be totally fre from corrosion as well as non conductive and shock proof. Pole should be providedwith

FRP/GRP base bracket dully fabricated from metal(M.S) and dully claded with FRP/GRP material to avoid any

metal exposer and painted with PU paint.Pole should mechanical properties i.e 1. Specfic gravity (ASTM D

792) 1.3-1.8 Kg/m3, 2. Glass Content % by weight (ASTM D 2584) 45.0 -55.0%, 3. Water absorption (ASTM D

570)<0.5%, 4. Tensile Strength(ASTM D 638) 200+/-50Mpa, 5. Flexural strength (ASTM D 790) 250+/-50Mpa,

6. Compressive Strength (ASTM D 695) 200+/-50MPa, 7. Yeild Strength(ASTM D638) 250 +/-50MPa.

Pole should be flame retardant as per IS 6746.Resin used shall be UV resistance and pigmented. Pole should

155 be painted with first coat of epoxy primer and then two coat of highly weather resistance polyurethen paint

to ensure proper addhesion of the paint.Minimum thickness shall be 80 to 100 micron.Defelection of the pole

shall not exceed more than 10.0 % of the length of the pole for the given load.Pole should be generally made

as per the dimensional data,performance criteria and some interchagebility features of poles as per the

standard ANSI C123.20 latest version of ASTM D 923/01 including cable termination box with necessory

accessories.The size of pole and type of installation with foundation , Anchor Base & Internal junction box as

per the manufacturer details and site requirement .

(3) 'B' class (Heavy Duty) frp/grp pole suitable for base plate mounting [B] Overall Length of 4.0 meter,

Average thickness : 6mm, Top/Bottom Outside Dia. 76/143mm +/-2.Weight of Pole 15.4 Kg approx. (Without

base) Metal Anchor Base dully frp claded (Size : 290 Ø * 12mmthk , Mounting hole PCD 240mm * 4 nos. of

Supplying and erecting Street light pole bracket comprising main B Class MS pipe of 4.2 cm/require outside

dia. complete with suitable B Class M.S. sleeve tubing of approx. 45cms.length and suitable for

76.5mm/80mm/require size of pole top having nuts and bolts for fixing the brackets and having spread of

156 mtr. Length with 110 deg.with vertical plane and suitable welded stiffener reducer and nipple with check nut 2 each 446

complete painted with one coat.of Red oxide / PU base primer and two coats of Aluminium / PU paint. paint

with following nos of arms. [A] Single Arm bracket 0.5 Mtr

Painting of street light pole having post top lantern complete with primer with two coats of Aluminium paint.

Painting of street light pole with bracket complete with two coats of Aluminium paint for following size of

pole.(A) up to 4 mtr

159 Providing and erecting C.I./M.S. flange type base plate of 300mm x 300mm x 6mm 2 each 238

Providing and fixing Terminal board of size 5.0 x 127 x 152.4 mm.bakelite sheet with suitable brass studs with

160 nuts, washers and clamps of size 25mm x 3mm suitable for pole painted with one coat of red lead paint. 2 each 145

Providing and erecting cable clamp of 25 mm X 3 mm M.S. flat suitable for fixing 2 Nos.of armoured cable

with nuts and bolts. (B) for 140 mm dia. Pole

Providing 1:2:4 cement concrete foundation & 70 % PCC from bottom including excavation for the pole of

size 45 x 45 x 100 cm. Deep in below ground level with plinth of 45 cm x 45 cm (or 45 cm dia x 45 cm) high

upper ground level with necessary curing and finishing in approved manner.( for 4 & 6 mtr pole)

Supplying and erecting LED street light fittings with High power White LEDs wattage of 3 Watt and above

assembled on single MCPCB, efficiency more than 130 lm/w and corrosion free High pressure die cast

aluminum housing with smooth finish powder coated and heat sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses, with toughened glass with company mark/name engraved or embossed 160 to

270 V,Power Factor more than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45, Luminaire

efficacy> 100 lumens/watt . LED driver efficiency > 85 %.( fittings required LM-79 & LM-80

certificates)(NOTE: Below description have shown ranges of Wattage capacity of LED fittings.The Engineer

protection -4KV integral and ,Light must have 440VAC line supply with over-voltage protection. (ii) above

to 60 Watts Cat-lll

Supplying & erecting approved make IP 55 grade Company fabricated Timer Panel of following capacity for

switch On-Off street lights on time scheduling basis made from 16G CRCA sheet duly epoxy power painted

164 inside and outside with hinged doors and locking arrangement consisting of suitable size of 4 Pole MCB and 4 1 each 16891

pole contactor (cat-III)with analog time switch, auto manual switch of same make and suitable input and

output Bakelite terminals and with door earthing approved by Engineer in charge.(C) 32 Amp

Supplying & erecting approved make SMC press moulded composite FRP. loop-in, loop-out approx. 2mm

thick box complete with Bakelite connector strip 5way(3P+N+E),DIN rail for mounting mob & hinged doors as

165 per requirement having locking arrangements with mounting clamp with nuts, bolts & washers suitable for 2 each 472

erection on pole with cable clamps& earth bolt of following size of box.( c)150mm x 125mm x 100mm [deep]

Supplying and erecting LED flood light fittings with High power White LEDs wattage of 1Watt and above

assembled on single MCPCB, efficiency more than 130 lm/w and corrosion free High pressure die cast

aluminum housing with smooth finish powder coated and heat sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses with company mark/name engraved or embossed 120 to 300 V,Power Factor

more than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45, Luminaire efficacy>

lumens/watt . LED driver efficiency > 85 %.CREE / OSRAM / PHILIPS Lumileds / NICHIA / SEOUL/ BridgeLux

166 (U.S.A.) make LED used for luminaire. ( fittings required LM-79 & LM-80 certificates)(NOTE: Below 15 each 6028

wattage capacity between the ranges shown.) (A) Street Light (IP-65), Surge protection -4KV integral and

kv non integral ,Light must have 440VAC line supply protection. It should withstand 48 hours for 440VAC line

supply(B) Flood Light (IP-65), Surge -4KV,Light must have 440VAC line supply protection. It should withstand

48 hours for 440VAC line supply ((iii) Above 60 to 90 watts Cat-ll

FANS & ACCESSORIS.Providing & erecting Approved make Power Saving 50 Watt Ceiling Fan with double ball

bearing ISI mark with Condenser 230 volt A.C. 50 Hz 1200 mm sweep complete having 3blades with

aluminium blades with , canopy & 30 cm. down rod erected with earthing.(Make shall be approved by

Engineer in charge)

Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to the RCC bars up to 50mm length

168 each side and pierced through a 16 Gauge M.S. box / Heavy Duty PVC box complete erected concealed in 6 each 107

Ceiling with necessary finishing.

169 Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or Fan box. 6 each 18

EXHAUST FANS.Supplying & erecting approved make low noise decorative exhaust fan having square frame

ABS body with inbuilt lowers & square frame.200mm with 1350RPM. Cat-II

Providing and fixing 12W LED garden bollard light suitable for pathway illumination, comprising die-cast

aluminium body with polycarbonate diffuser, warm white LED (3000–4000K), IP65 weatherproof rating, and

171 operating on 220–240V AC supply. The fixture shall be approximately 600–750 mm height, mounted on a 26 each 5551

concrete base with necessary anchor bolts, wiring, and accessories, complete as required for proper

installation and functioning.

Providing and erecting required size HOT deep Galvanised iron strip for earthing of H.T. , OCB/ ACB/

Transformer LT panel board, Motors etc. using proper clamp.

Providing and erecting HOT deep Galvanised iron strip wire 8 to 16 SWG.Using for DB earthing wire 8 to

Supplying & erecting in earthpit of minimum bore dia. 225mm size ASH or approved make Safe Earthing

Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of corrosion free G.I.Pipes having

Outer pipe dia of 80 mm having 80-200 Micron galvanising, Inner pipe dia of 40 mm having 200-250 Micron

galvanising, connection terminal dia of 14 mm with constant ohmic value surrounded by highly conductive

174 compound with high charge dissipation suitable for panel earthing.[A] For electrical installation up to 440 V(c) 6 each 7025

For Electrical Installation covering Transformer Neutrals, Lightning arrester Earthing, A.C.Plant & Sensitive

Computer System(like Automation, SCADA) i.e independent Earthing in normal soil. [B] For Electrical

installation up to 11 KV located in other than normal soil i.e. Soft Rock, Marshy Soil etc. -Length of

Pipe : 2 mtr -Back filling Compound :1 no. Bag of 25 Kg.

Supplying & erecting in earthpit of minimum bore dia. 225mm size ASH or approved make Safe Earthing

Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of corrosion free G.I.Pipes having

Outer pipe dia of 80 mm having 80-200 Micron galvanising, Inner pipe dia of 40 mm having 200-250 Micron

galvanising, connection terminal dia of 14 mm with constant ohmic value surrounded by highly conductive

175 compound with high charge dissipation suitable for panel earthing.[A] For electrical installation up to 440 V(c) 1 each 10489

For Electrical Installation covering Transformer Neutrals, Lightning arrester Earthing, A.C.Plant & Sensitive

Computer System(like Automation, SCADA) i.e independent Earthing in normal soil. Length of Pipe :

mtrs Back filling Compound :2 nos Bags of 25 Kg.

Supplying & erecting approved make Telephone Cable electrolytic copper conductor PE insulation twisted in

two pairs, & wrapped with FRLS PVC tape & sheathed with FRLS PVC or HFFR outer Jacket suitable for

176 telephone wiring & confirming to C-DOT erected in existing pipe. of following size of conductors & nos.of 80 rmt 124

pairs. With necessary connections. (b) Armoured [Jelly Filled] 1) Ten Pairs

SITC of Digital / PCM / TDM EPABX System having SMT design, system with flexible universal slots. Inbuilt

Auto attendant facility, Minimum 15 Nos. conference, Analog extension line, Calling GSM, E&M line, PRI / EI

& VOIP program me through Analog telephone digital key from Ethernet, public address cord, shall have

unrestricted simultaneous dialing facility,QSIG protocol on PRI, 95 / STD / ISD / Local-Locking, Class of

Service, Quick Dial-Single Digit dialing of any two external number, Once only ring device, Boss/Secretary-Do

not disturb Facility, Power Down Mode, Hot Line, Hot Outward Dialing, Day Night Mode, Auto Call Back,

177 Barge-in, Call Pick Up & Call Transfer, Call transfer while Ringing with Voice Guide System, (DISA), Caller ID 1 nos 44949

(CLI), CLI Base ECF, CLI Base routing Internet Ready Port, External Music Port, Call Budgeting, Call Most

Calculation (ASMDR), DID Direct Inverse Dialing, External Music Input, Fax Homing, Global Directory Printing

with following capacities [A] No of Extension 16, No of Junctions 6, 8 Port IP Resource in-built, 4 Port Web

base Video Conferencing, No of expandable ports : 48, Operators Console - 01 Compatible : ISDN

Supplying & erecting approved make LAN cable of following size in existing pipe as per direction. [D] CAT - 6 e

Providing following type of Modular Type Accessories mounted with pvc / metallic box, single mounting base

179 frame covered with textured / metallic front plate , modules erected with necessary connection. As desired 2 nos 326

by Engineer In charge (19) Modular Indicating Call Bell.Cat.III

Providing following type of Modular Type Accessories mounted with pvc / metallic box, single mounting base

180 frame covered with textured / metallic front plate , modules erected with necessary connection. As desired 2 nos 148

by Engineer In charge(20) Modular Buzzer.Cat.III

Providing and erecting water cooler having storage capacity 80Ltr. & cooling capacity 40 Ltr.per hour @ an

ambient temp of 45˚ C. The outlet temp. of the water should drop by 15˚ C within a hour, The water cooler

181 should be comprising of hermetically sealed compressor, fan motor, condensing unit, water tank surrounded 2 each 49069

by evaporating coil, thermostats, relay etc. complete with necessary inlet & outlet connection. The body of

water cooler will be made from Stainless Steel. ◦

Supplying & erecting 5 stage single reverse osmosis water purification system with M.S. powder coated

frame, prefilter housing with 'O' ring presediment filter GAC filter, carbon filter suitable buster DC pump

182 capacity 80 psi, mention with 40 psi inline type post carbon filter auto low & high pressure switches with 2 each 28899

following size of storage tank & LPH capacity & erected as directed [C] 50 Ltr / Hr with 150 psi 2 nos booster

Providing Water proof straight Joint in PVC insulated flat flexible copper cable by using insulating material,

water proofing material, & making the joint complete. (A) Up to 10Sq. mm

Supply, Installation, Testing and Comissioning of 4MP Fixed Lens Dome Type Camera,H.265 4MP IR Vandal

Proof Dome N/W Camera, 2.8mm/3.6mm, 30M IR, Micro SD, DC12V/PoE, IP67/IK10, Basic IVA, 1 / 2.7"

184 CMOS, 2560 × 1440, 0.01 Lux, F1.2, AGC ON; Defog, True day/night, Digital WDR, 3D DNR, HLC & BLC, Triple 4 each 10166

streams, Smart codec by ROI, Cyber Security, Basic intelligent video analytics, NDAA Compliance, UL, CE, FCC

Certified (Including Five year free maintenance with guarantee)

Supply, Installation, Testing and Comissioning of 24 Channel Network Video Recorder (NVR), Support

24CH@2MP, H.264 Video Compression, HDMI, VGA output, up to 4 SATA interface each with max 6 TB

support, bandwidth 200 mbps, CE FCC, BIS, Operating Temp -10 deg to 50 deg C, USB and serialInterface

(Including Five year free maintenance with guarantee)

186 Supply Installation Testing & Commissioning of 8TB Surveillance Harddisk 1 each 15000

SITC of 24 x 10/100/1000BASE-T ports 4 x Gigabit RJ45/SFP Combo ports Advanced L2 switching and security

187 features L2+ Static Routing Optional “standard mode” or “surveillance mode” management user interface 1 each 31680

(Including Five year free maintenance with guarantee)

SITC of LIU 12 PORT Rack Mount - Loaded (LC) SM (Including Five year free maintenance with guarantee)

SITC of SCREEN SIZE 80 cm diagonal (32” INCH), RESOLUTION HD (1366*768), USB INPUT (2.0 SUPPORT)

2*Side(USB2.0), HDMI INPUT 3*Side(HDMI 1.4), USB DEVICE SUPPORT USB Supported HDD, HOTEL MODE

189 Yes, Basic, BLUETOOTH Yes (Ver. 4), WIFI TYPE(STANDARD) 802.11a/b/g/n 2.4G 2T2R, Built-in, WIFI BAND 1 each 40850

TYPE 2.4GHz, OS & VERSION INFO Android 'P' - 9.0, MEMORY FLASH 8GB EMMC, RAM 1.5GB , DDR3

Mhz. (Including Five year free maintenance with guarantee)