GE AF AMB-17/2020-21 REPAIRS TO FLOORING PLUMBING SANITARY FITTINGS PLASTERING AND PERIODICAL SERVICES TO OTM / STORAGE ACCOMMODATIONS IN TECHNICAL AREA AT AF STATION AMBALA UNDER GE AF AMBALA

Amount

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundations, manholes, etc. or for laying cables/pipes, erecting poles, etc.not exceeding 10sqm on plan and getting out in soft / loose soil complete all as specified and as directed

Returning, filling in, including, spreading, leveling, watering and well ramming in layers not exceeding 25cm deep as in any type of soil complete all as specified and as directed

Removing excavated materials to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point in soils including spreading in low lying area and leveling complete all as specified and as directed

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering complete all as specified and as directed

Dismantling asbestos cement (corrugated/semi corrugated) in roof coverings, etc including ridges, claddings, etc. and disposing off including all necessary staging / scaffolding, etc. as required complete all as specified and as directed

Demolition of plain cement concrete in ground floors and pavings not exceeding 15cm thickness (below or above ground level) and removal of debris complete all as specified and as directed

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) as in cover slabs, removing debris from site and making good the disturbed surfaces / portions in existing specifications complete all as specified and as directed

Demolition of brickwork or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles and disposing off complete all as specified and as directed

Dismantling boarding including fillets of any decription fixed in any position with nails / screws, etc. and disposing off complete all as specified and as directed

Dismantling timber scantlings 40sqcm and over in section, in any position and disposing off complete all as specified and as directed

Dismantling timber fillets, rails, posts, rafters, purlins, etc. under 40sq. cm in section in any position and disposing off complete all as specified and as directed

Dismantling ceiling boards (fibre, pulp, insulation, etc. or insulation boards/slabs/blankets, any thickness including cover fillets and disposing off complete all as specified and as directed

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) and disposing off complete all as specified and as directed

Demolition of mud in roofs, any thickness, including plastering and leaping (whether full thickness removed or only a part thereof) complete all as specified and as directed

Dismantling brick tiles or terracing tiles, single layer on roofs, sorting of serviceable tiles and stacking complete all as specified and as directed

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for keys, scubbing down with water, etc. including all necessary scaffolding as required and rubbishing off the premises, etc. complete all as specified and as directed

Taking down cement or cement lime plaster, any description on concrete, etc. ceiling surfaces, hacking for keys, scubbing down with water, etc. including all necessary scaffolding as required and rubbishing off the premises, etc. complete all as specified and as directed

Taking up or down 15mm bore steel water tubing and connections including cleaning and setting aside for refixing or disposing off, etc. complete all as specified and as directed

Taking up or down 20mm bore steel water tubing and connections including cleaning and setting aside for refixing or disposing off, etc. complete all as specified and as directed

Dismantling and taking down PVC OH water tanks, 250/500litres capacity from any position / location including all hoisting/lifting, etc. and disposing off complete all as specified and as directed

Dismantling and taking down PVC OH water tanks, 501 to 1000litres capacity from any position / location including all hoisting/lifting, etc. and disposing off complete all as specified and as directed

Taking down chowkats or frames not exceeding 1.5sqm each with shutters (without taking off shutters from the frame) and disposing off complete all as specified and as directed

Taking down chowkats or frames exceeding 1.5sqm but not exceeding 4sqm each but with shutters (without taking off shutters from the frame) and disposing off complete all as specified and as directed

Taking down shutters of any description not exceeding 1sqm area and disposing off complete all as specified and as directed

Taking down shutters of any description exceeding 1sqm but not exceeding 2.0sqm area and disposing off complete all as specified and as directed

M&L for cutting into brick walls built, in cement mortar superficial area not exceeding 150sqcm complete all as specified and as directed

M&L for providing saw dust filling / laying in compacted thickness in any positions / locations, etc. in firing range complete all as specified and as directed

M&L for sand filling / laying in any positions / locations, etc. in firing range complete all as specified and as directed

M&L for providing and injecting chemical emulsion for post constructional anti-termite treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25litre / linear metre including drilling and plugging holes, etc. in aprons, etc. complete all as specified and as directed

M&L for treatment of soil under existing floors using emulsion @ 1.0litre / hole, 300mm apart including drilling and plugging 12mm dia holes with cement and coarse sand mortar (1:2) to match the existing floors complete all as specified and as directed

M&L for roughening of concrete surfaces and applying cement slurry @3kg/sqm complete all as specified and as directed

M&L for 100mm thick plain cement concrete 1:4:8 (type D-2) using 40mm graded stone aggregate as in sub-bases, pavings, etc. complete all as specified and as directed

M&L for plain cement concrete type A-0,1:1.5:3 (using 12.5mm graded stone aggregates) mixed with polymer in average depth of 30mm including taking down of spalled concrete, treating of reinforcement with SBR complete all as specified and as directed

M&L for 40mm thick plain cement concrete type B-1,1:2:4 (using 20mm graded stone aggregates) as in flooring, etc. complete all as specified and as directed

M&L for plain cement concrete type B-0,1:2:4 (using 12.5mm graded stone aggregates) as in kerbs, stops, padding and making good depressions, copings, etc. on roof and the like complete all as specified and as directed

M&L for 75mm thick plain cement concrete 1:3:6 (type C-2) using 40mm graded stone aggregate as in floors, plinth protection, pavings, etc. including making spike rolling to surfaces or making impressions of expanded metal whilst the concrete is green laid in alternate bays of 3m length and joints between bays filled with 85/25 grade bitumen and sand mix @ 1:2 complete all as specified and as directed

M&L for plain cement concrete 1:3:6 (type C-1) using 20mm graded stone aggregate as in filling of hold fast holes, etc. complete all as specified and as directed

M&L for RCC 1:2:4 type B-1 using 20mm graded mechanically crushed stone aggregates as in fins, fascia, louvers, parapets, railing, etc. exceeding 600mm in height complete all as specified and as directed

M&L for RCC 1:2:4 type B-1 using 20mm graded mechanically crushed stone aggregates as in slabs, landings, balconies, etc. complete all as specified and as directed

M&L for plain cement concrete 1:3:6 (type C-2) using 40mm graded stone aggregate for bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 110/150mm dia drain pipes complete all as specified and as directed

M&L for mild steel TMT bars grade Fe-500D, 10mm dia, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed

M&L for mild steel TMT bars grade Fe-500D, 5mm dia and over, upto and including 10mm dia, as in stirrups, spacers, etc. cut to length, bent to shape required including cranking, bending and binding with and including MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed

M&L for formwork to fins, fascia, parapets, chullah hoods, chajjas, troughs and similar items including edges for rough finished surfaces of concrete complete all as specified and as directed

M&L for formwork to chajjas, shelves and similar items including edges for fair finished surfaces of concrete complete all as specified and as directed

M&L for framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks, drain covers, FOD traps and similar works conforming to Fe-290 grade E-165 including all necessary staging, T&P for work on perimeter walls, at heights, etc. complete all as specified and as directed

M&L for framed works conforming to Fe 410-W (grade E-250) quality-A as in doors or gates of angle or other section with gusset plates, rails, braces, etc. drilled for fixing of steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing complete all as specified and as directed

M&L for mild steel works as in wind ties for roof, including securing bolts and all necessary rivetting, drilling, staging, etc. conforming to Fe-410-0 or Fe-310-0 complete all as specified and as directed

S&F steel work in tubular trusses including special shaped washers, etc. using ERW or induction butt welded tubes conforming to IS-1161-1979 structural grade 240 complete all as specified and as directed

S&F rolled mild steel in plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment, Fe 410W (grade-E 250) quality-A complete all as specified and as directed

M&L for brickwork with sub-class 'B' bricks, straight or curved on plan exceeding 6m mean radius built in CM (1:6) complete all as specified and as directed

--ditto-- all as per serial item No. 50 hereinabove but except bricks

M&L for brickwork with sub-class 'B' bricks, straight or curved on plan as in half brick thick walls built in CM (1:4) complete all as specified and as directed

M&L for 40mm thick brick tiles laid, bedded and jointed in 15mm thick CM screed 1:6, joints grouted in CM (1:3) complete all as specified and as directed

--ditto-- all as per serial item No. 53 hereinabove but except brick tiles

M&L rendering 15mm thick in cement mortar (1:6) on fair surfaces of PCC block / brick masonry wall / concrete surfaces, inner sides of drains, etc. finished even and smooth without using extra cement complete all as specified and as directed

M&L for rendering 15mm thick on brickwork or concrete surfaces, chajjas, etc. in CM (1:4) mixed with water proofing powder at rate of 3% of cement or as per manufacturer's instructions, finished even and fair without using extra cement complete all as specified and as directed Note: Water proofing compound shall be measured separately under respective item

M&L for rendering 5mm thick plaster, in cement mortar (1:3) on fair faces of concrete surfaces of soffits of slabs, ceilings, etc. finished even and smooth without using extra cement complete all as specified and as directed

Supply only integral water proofing compound as specified

M&L for rough cast plaster including 15mm thick rendering in CM 1:3 on brickwall or concrete surfaces complete all as specified in SSR Part-I clause 14.22 complete all as specified and as directed Note: Rough cast finish shall be made as under: (i) After applying the under coat of cement mortar 1:3 and while it is still in plasic state the rough cast mixture consisting of crushed stone or fine gravel / aggegates (of size between 6 to 12mm depending on the texture required) mixed with course sand and cement in the ratio of 1:1:1 shall be applied and finished even (ii) The mix of cement and sand shall be made slightly wetter than normal for rendering to ensure that larger aggregates are thoroughly covered

M&L for wire brushing and cleaning top surface of tiles, lime terracing or cement concrete, including flashings and junction of parapets, etc., and surface painting, with a layer of blown grade bitumen of any penetration applied hot @1.7kg/sqm, blinded with grit or pea size gravel @ 0.006cum/sqm and lightly tampered (area of flashings, etc. shall be added to the roof area) complete all as specified and as directed

S&F solid PVC wall lining consisting of 5mm thick plain coloured PVC sheet inclusive of solvent cement and fixing at site on PVC frame as detailed and shown in SSR Part-I complete all as specified and as directed

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC frame as detailed and shown in SSR Part-I complete all as specified and as directed

S&F in repairs MS tubing 20mm bore, PVC coated, tint, type and design as approved as in drapery rods / curtain rails with and including pair of fancy type end knobs complete all as specified and as directed

S&F in repairs venetian blind roller curtain, 1mm thick flap with adjustable type including all necessary fitting / fixing arrangements, of approved design and form, complete all as specified and as directed

S&F in repairs double action hydraulically operated controller, suitable for glass door upto 12sqm size, heavy duty, with sensor, including all necessary fitting / fixing arrangements all as per per manufacturer's instructions of existing type and approved deisgn complete all as specified and as directed

M&L for carefully taking out double action hydraulically operated controller, from glass door and refixing the same to existing or new door, after cleaning, oiling, greasing, etc. and checking serviceability complete all as specified and as directed

M&L for 12mm thick toughened glass door shutters, duly diamond polished, including all fittings/hardwares, stainless steel top and bottom patches, top pivot, door controller assembly (excluding controller), 2Nos. stainless steel 300mm long handles all as of approved design, type & pattern and checking serviceability / successful operation complete all as specified and as directed

S&F false ceiling with powder coated GI frame work for seamless ceiling comprising of GI perimeter channel 0.55mm thick with 2Nos. unequal flanges of 20 & 30mm and web 27mm fixed to surrounding wall using nylon sleeves at 900mm c/c with GI cleat and steel expansion fasteners with and including ceiling section (not exceeding 1.2m in length) of 0.55mm thickness, having curled web of 50mm and flange 26mm each with lips of 10.5mm fixed to intermediate channel with connecting clips at 457mm c/c to 6mm dia GI hangers (1.2m long) adjusting level fixed to roof slabs by means of ceiling cleats made of GI flat 40x3mm, 60cm long and expansion hold fasteners 12.5mm dia 40mm long including 9 to 10mm thick ceiling boards / tiles (of approved design) of size 600x600mm for insulation and accoustic purposes, decorative type, with silver foil coating on backsides fixed with staples on snap grid with and including 4mm dia GI wire, nuts, bolts, washers, etc. complete all as specified and as directed

M&L for non-skid ceramic tiles, coloured, 7 to 8mm thick, joint free, edge cut, exceeding 0.06sqm and not exceeding 0.11sqm in size, of superior quality on floors, etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the colour of tiles with and including 15mm thick screed bed in CM 1:4 complete all as specified and as directed

M&L for glazed ceramic tiles, coloured of size 450x300x7 to 8mm thick, of superior quality on vertical faces, dados, skirting, risers, etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the colour of tiles with and including 10mm thick backing coat in CM 1:4 complete all as specified and as directed

M&L for vitrified tiles, coloured, double charged (nano series) 10mm thick, joint free, edge cut, area of each tile not exceeding 0.36sqm, of superior quality on floors, etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the colour of tiles with and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed

M&L for vitrified tiles, coloured, double charged (nano series) 10mm thick, joint free, edge cut, area of each tile not exceeding 0.36sqm, of superior quality on vertical faces, skirting, etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the colour of tiles with and including 10mm thick screed bed in CM 1:4 complete all as specified and as directed

M&L for machine cut and machine polished kota stone slab 600x600mm size, 20 to 25mm thick as in floors, laid over and including 20mm thick screed bed in CM 1:4 (rate shall be included), set and jointed in neat cement slurry and pointed with cement and pigments to match the shade of slab including rubbing and polishing etc. complete all as specified and as directed

M&L for machine cut and machine polished kota stone slab 600x600mm size, 20 to 25mm thick as in vertical faces, cladding, etc. fixed over and including 10mm thick screed bed in CM 1:4 (rate shall be included), set and jointed in neat cement slurry and pointed with cement and pigments to match the shade of slab including rubbing and polishing etc. complete all as specified and as directed

M&L for 20mm thick granite stone slab, of any type, table rubbed and polished, in steps, jambs, window cills, cooking platforms and the like in laid over and including 20mm thick screed in cement mortar (1:6) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of slab complete all as specified and as directed

M&L for 20mm thick granite stone slab, of any type, table rubbed and polished, in vertical faces, cladding and the like in laid over and including 10mm thick screed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of slab complete all as specified and as directed

M&L for marble 18 to 20mm thick (table rubbed and polished) of approved shade in cooking platforms and the like bedded in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including taking down old slab complete all as specified and as directed

M&L for preparing of new steel surfaces of any description over 10cm in width or girth and applying two coats of synthetic enamel paint (tint as approved) over a coat of red oxide zinc chrome primer complete all as specified and as directed

M&L for preparing of new / old wood / wood based surfaces of any description over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, tint as approved complete all as specified and as directed

M&L for preparing of old treated / untreated wood / wood based surfaces of any description over 10cm in width or girth and applying one coat of synthetic enamel paint (tint as approved) complete all as specified and as directed

M&L for preparing of old treated / untreated structural steel surfaces of any description like rafters, trusses, purlins, angle iron posts, etc. over 10cm in width or girth and applying one coat of synthetic enamel paint (tint as approved) complete all as specified and as directed

M&L for preparing of old treated / untreated steel surfaces of any description like gates, frames, fencing, etc. over 10cm in width or girth and applying one coat of synthetic enamel paint (tint as approved) complete all as specified and as directed

M&L preparation of new plastered / unplastered masonry / concrete wall surfaces, etc. and applying two coats of exterior acrylic anti-fungal paint (tint as approved by the GE) in camouflage pattern as per manufacturer's instructions with all staging as required complete all as specified and as directed

M&L preparation of old treated plastered / unplastered masonry / concrete wall surfaces, etc. and applying one coat of exterior acrylic anti-fungal paint (tint as approved by the GE) in camouflage pattern as per manufacturer's instructions with all staging as required complete all as specified and as directed

M&L preparation of new plastered / unplastered wall surfaces of any description and applying two coats of cement based paints (tint as approved by the GE) in camouflage pattern as per manufacturer's instructions with all staging as required complete all as specified and as directed

M&L for preparation of new masonry / concrete wall surfaces and applying two coats of oil emulsion distemper over a coat of wall primer including a coat of wall care putty 1mm thick including all necessary staging, scaffolding, safety precautions, etc. as required to work at heights, etc. complete all as specified and as directed

M&L for preparation of old treated / untreated plastered / unplastered masonry / concrete wall surfaces and applying two coats of oil emulsion distemper including all necessary staging, scaffolding, safety precautions, etc. as required to work at heights, etc. complete all as specified and as directed

M&L for preparation of old treated / untreated plastered / unplastered masonry / concrete wall surfaces and applying one coat of oil emulsion distemper including all necessary staging, scaffolding, safety precautions, etc. as required to work at heights, etc. complete all as specified and as directed

M&L preparation of newly plastered / unplastered surfaces and applying three coats of white / colour wash on walls, etc. complete all as specified and as directed

M&L preparation of newly plastered / unplastered surfaces, and applying three coats of white / colour wash on ceilings, etc. complete all as specified and as directed

M&L preparation of old treated / untreated plastered / unplastered surfaces and applying three coats of white / colour wash on walls, etc. complete all as specified and as directed

M&L preparation of old treated / untreated plastered / unplastered surfaces, and applying two coats of white / colour wash on walls / ceilings, etc. complete all as specified and as directed

M&L preparation of old treated / untreated plastered / unplastered surfaces and applying one coat of white / colour wash on walls, etc. complete all as specified and as directed

M&L preparation of old treated / untreated plastered / unplastered surfaces and applying one coat of white / colour wash on ceilings, etc. complete all as specified and as directed

M&L preparation of old plastered / unplastered, treated / untreated surfaces over 10cm in width or girth and applying one coat of plastic paint complete all as specified and as directed

S&F galvanised, corrugated mild steel sheeting, 0.63mm thick with two corrugations side lap, fixed with coach screws and washers, in roofs, walls, etc. with grade of zinc coating 275 complete all as specified and as directed

--ditto-- all as per item No. 96 hereinabove but except sheets

S&F 6mm thick asbestos cement corrugated / semi-corrugated sheets in roof / walls fixed with 'L' or 'J' hooks or cranked hook bolts, and bituminous washers, etc. and joints suitably sealed, complete all as specified and as directed

S&F 6mm thick asbestos cement serrated ridge for corrugated or semi-corrugated sheets complete all as specified and as directed

S&F 2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugations side laps fixed with 'L' or 'J' hooks or cranked hook bolts, and bituminous washers, etc. and joints suitably sealed complete all as specified and as directed

M&L for taking down wooden shutters of any description area not exceeding 1.0sqm each and refixing / resecuring same after necessary easing, adjusting, repairs, etc. with providing new screws complete all as specified and as directed

M&L for taking down wooden shutters of any description area exceeding 1.0sqm but not exceeding 2.0sqm each and refixing / resecuring same after necessary easing, adjusting, repairs, etc. with providing new screws complete all as specified and as directed

S&F aluminium anodized window shutters and frame with aluminium guard bars, made out of hollow extruded aluminium sections (as detailed below), each shutter having 2Nos. aluminium hinges 100mm long, 1No. lock type aluminium handle 100mm, 2Nos. 150mm long aluminium tower bolts and including 5mm thick tinted glass fixed with glazing clips, rubber beading, gaskets, aluminium beading screws, etc. as required complete all as shown on drawing, as specified and as directed Details: Shutter size - 100x44mm x1.6mm thick Chowkhat size - 100x44mm x1.6mm thick Notes: (i) Drawings shall be referred at GE (AF) Ambala (ii) Minimum thickness of anodisation shall be 15microns

Supplying and fixing in position anodised (minimum thickness of anodising shall be 15microns) aluminium door and chowkhat made out of hollow extruded aluminium sections as detailed, each door having 02Nos disc or 'D' type handles, 02Nos aluminium tower bolts 200mm size, one brass mortice lock six levers with key in duplicate, fixed with aluminum hinges to chowkhat shutter, partly glazed with 5mm thick tinted glass and partly paneled with 12mm thick prelaminated particle board fixed with glazing clips, rubber beading / gasket anodized aluminium beading screws, etc. complete all as specified and as directed Section details: Chowkhat Frame: 110.60x44.45x1.55mm thick Shutter vertical/stile: 85x44.45x1.54mm thick Shutter middle rail: 83.50x44.45x1.54mm thick Top & bottom rail: 115x44.45x1.54mm thick

M&L for aluminium anodised (minimum thickness of anodising shall be 15microns), white or tint as approved, grill of design DG-104 pattern (10X5.2mm), fixed with anodised aluminium 'F' sections (20.6x15.2x1mm) to aluminium window / ventilators, etc all as per manufacturer's instructions complete all as specified and as directed

S&F anodised (minimum thickness of anodising shall be 15microns) aluminium partition wall, fabricated, size of members 100x44x1.6mm, including making provision for opening, etc. and all necessary cleats, panel inserts not more than 1.44sqm and arrangement to receive and including 5.5mm thick glass and 19mm thick pre-laminated particle board with aluminium beading, glazing cleats, and stainless steel screws, rubber gaskets, beading, etc. complete all as specified and as directed

S&F 30m thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed

S&F 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauge, etc and divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, sizes of members of shutters as specified in clause 8.20 9(b) of SSR Part-I, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., supplied and fitted to chowkats complete all as specified and as directed

S&F pressed steel frames of size 125x60mm, fabricated out of 1.25mm thick MS sheet, for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and as directed

S&F solid PVC door frame of size 50x47mm made out of 5mm thick plain / printed coloured PVC sheet (as approved) reinforced with MS square tube all as per specifications and drawing given in SSR Part-I 2009 all as per manufacturer's instructions and making good the disturbed surfaces complete all as specified and as directed

S&F factory made solid panel PVC door shutter, 30mm thick, consisiting of MS frame made out of MS tubes for top and bottom rails, MS frame shall be moulded with plain coloured PVC 'C' channel and having PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain coloured PVC sheet top rail, lock rail and bottom rails, paneling of plain coloured PVC sheet to be fitted in MS frame welded / sealed to stiles and rails with suitable PVC sheet beading and jointed together using solvent and fixed in position in frame as per site requirement and specified in MES Schedule 2010 complete all as specified and as directed Door Width Size of style Size of rails exceeding 1.5' but not exceeding 2' 50mm 50mm exceeding 2' but not exceeding 2.5' 50mm 75mm exceeding 2.5' but not exceeding 3' 75mm 100mm exceeding 3' 100mm 125mm

S&F steel window (box type) factory made double shutter (glazed and wire gauzed) with side hung shutters including pintle type hinges, steel handles fabricated type for each leaf duly welded, mild steel barrel tower bolts 150mm size (02Nos for each leaf) duly welded, with glazing bars dovetailed or welded including MS fillets, including provision and welding of guard bars including one shop coat of red oxide primer over window, frame & guard bars complete all as specified and as directed Notes: (i) Windows shall be fabricated as per HQ CE Chandigarh Zone drawing No. TD-219 Sh 1/3 to 3/3 dated 02 Jan 2007 amended dated 22 Jun 07 in Sh 1/3 and dt 15 Jun 07 in sh 2/3 & 3/3 & TD-220 sheet 1/3 to 3/3 These drawings shall be referred from the office of GE (AF) Ambala/HQ CWE AF AMBALA (ii) Glazing and wire gauge shall be measured and paid separately (iii) Double shutter area of opening shall be measured for payment purposes

--ditto-- all as per serial item No. 112 hereinabove but without glazing bars

S&F steel ventilator with top hung shutter including hinges, steel peg stay, with glazing bars complete all as shown on drawings, as specified and as directed

S&F block boards, 18/19mm thick, grade 2 quality, interior grade, commercial type, fixed with screws to timber framework as in cupboard shutters complete all as shown on drawings, as specified and as directed

S&F in repairs 12mm thick pre-laminated particle boards, prelaminated both sides with decorative choice laminations, with glazing clips, rubber / aluminium beading / gasket, suitable for aluminium doors, etc. complete all as specified and as directed

S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified and as directed

S&F 4mm thick sheet glass, ordinary quality, area not exceeding 0.5sqm in each pane, cut to required size and shape to existing wooden shutters / MS windows / shutters, etc. with glazing clips, glass oil putty, etc including hacking out old broken glass (any thickness), cleaning hacked grooves, removing damaged putty, beads, etc complete all as specified and as directed

S&F 4mm thick pin head, figured, glass area not exceeding 0.5sqm in each pane, cut to required size and shape to existing wooden shutters / MS windows / shutters, etc. with glazing clips, glass oil putty, etc including hacking out old broken glass (any thickness), cleaning hacked grooves, removing damaged putty, beads, etc complete all as specified and as directed

S&F 5mm thick tinted glass area exceeding 0.5sqm in each pane, cut to required size and shape to existing wooden / MS alluminium door / shutters, etc. with glazing clips, alluminium & rubber beadings, oil putty, etc including hacking out old broken glass (any thickness), cleaning hacked grooves, removing damaged putty, beads, etc complete all as specified and as directed

M&L for running weld to small fittings, hinges, etc. of steel doors / windows and making same functional, thickness of metal to be welded exceeding 6mm but not exceeding 9mm complete all as specified and as directed

M&L for running weld to parts of steel ladders, etc. at any location / position and making same functional, thickness of metal to be welded exceeding 6mm but not exceeding 9mm complete all as specified and as directed

M&L for welding in repairs, exceeding 2.5cm but not exceeding 5cm in length, thickness of metal to be welded exceeding 6mm but not exceeding 9mm complete all as specified and as directed

S&F 100mm butt hinges, stainless steel, medium weight with stainless steel hinge pin and fixed complete all as specified and as directed

S&F in repairs 100mm butt hinges, aluminium, cast type, with stainless steel hinge pin and fixed complete all as specified and as directed

S&F150mm long, aluminium door / window handles, fabricated type with back plate 3mm thick, complete all as specified and as direct

S&F 250mm aluminium anodised hasp and staple, bolt type, with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed

S&F 200mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and as directed

S&F in repairs 150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and as directed

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed

S&F in repairs stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed

S&F double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed including taking off shutters any type if required complete all as specified and as directed

S&F door closer hydraulically regulated, aluminium (die cast) body, designation No. 2, universal type, suitable for door shutters of 701 to 850mm in width and of weight between 36 to 60kg and fixed including taking off shutters any type if required complete all as specified and as directed

S&F mortice lock, vertical type, size 100mm, 6 levers, with two sets of keys complete all as specified and as directed

S&F floor door double legged / ledged stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and as directed

S&F MS chromium plated bracket holders, of approved design and tint, suitable for 20mm dis curtain rods fixed to pelmet boxes with stainless steel screws complete all as specified and as directed

M&L for petty repairs to aluminium doors of any size, viz. adjusting the frame, shutters, etc. easening out, tightening of handles, tower bolts, floor/top springs, door closures, etc. oiling / greasing all moving parts / components, etc. and ensuring serviceabilty and easy operation complete all as specified and as directed

M&L for petty repairs to aluminium windows of any size, viz. adjusting the frame, shutters, etc. easening out, tightening of handles, tower bolts, tightening of gauge/glass and ensuring serviceabilty and easy operation complete all as specified and as directed

M&L for petty repairs to steel windows of any size, viz. adjusting the frame, shutters, etc. easening out, tightening of handles, tower bolts, tightening of gauge/glass and ensuring serviceabilty and easy operation complete all as specified and as directed

M&L for repairs to steel gates of size 5 to 6.5m wide and 7 to 9.5m height including activating necessary T&P, jack lifters, etc. and making good damaged cover plates, GI sheetings, wheels, axle shafts, etc. including welding, oiling, greasing, etc. to ensure complete serviceability and refixing same after repairs complete all as specified and as directed

M&L for taking out axle from wheel, remetalling the worn out bearings, straining the shaft, making 2Nos. hearing sheets, washing tearings with kerosene, graesing all moving parts / componentsand refixing baering to shaft and reassembling rail wheels, etc. after repairs complete all as specified and as directed

M&L for pulling over rail of sliding gates alternately with help of tuffer machine after establishing suitable anchorage, cleaning the rails by chiseling out bituminous, cement, dirt, grease deposits, etc. and regreasing all moving parts / componenets to ensure serviceability after repairs complete all as specified and as directed

M&L for aligning gates over rails by setting overhead guide channels for smooth movements as required complete all as specified and as directed

M&L for MS locking clain, 12mm dia including welding to gates as required complete all as specified and as directed

M&L for fabricating suitable locking arrangements with MS angle 40x40x6mm and MS flats 50x6mm alongwith MS rod 16mm dia including all necessary welding, bolting, etc. complete all as specified and as directed

M&L for taking down door shutters of blast pens and refixing the same after minor repairs, welding to work out parts, etc. applying two coats of synthetic enamel paint (tint as approved) over a coat of zinc chrome primer complete all as specified and as directed

Notes for item Nos. 137 to 146: (i) All joineries, items, etc. shall be maintained at any position and or at any location (ii) Staging, T&P, safety precautions / measures, etc. shall be provided to work at heights and or as required at site (iii) Minor spares viz. screws, gaskets, washers, etc. as required shall be included in rates quoted (iiii) Maintenance shall ensure complete serviceability and shall be to the entire satisfaction of the Engineer-in-charge (iv) Maintained joineries, items, etc. shall be under defect liability period and shall be redone if the same are found / gets non-functional within the said period (v) The quoted rates shall be deemed to be inclusive of the above aspects

Fixing only steel water tubing, medium grade, galvanised with screwed and socketed joints, including supply and fixing all fittings, ISI marked conforming to IS -1239 and fixed to walls or laid in floors / trenches required for protection of electric clables complete all as specified and as directed for the following bores: Note: Serviceable tubings obtained from serial item Nos. 18 & 19 will be reused under this item

S&F steel water tubing, medium grade, galvanised with screwed and socketed joints, in any length, including supply and fixing all fittings, ISI marked conforming to IS -1239 and fixed to walls or laid in floors / trenches required for protection of electric clables complete all as specified and as directed for the following bores:

Supplying, hoisting, fixing and connecting up rotational moulded polythylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including connecting the overflow drain out, inlet and outlet pipes, tank nipple, elbow, bend, unions, sockets, etc. complete all as specified and as directed of the following capacities:

500litres

1000litres

S&F 15mm dia stop valves / angle valves, concealed type, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions or for brass ferrule complete all as specified and as directed

S&F 15mm dia stop valves / angle valves, fancy type, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions or for brass ferrule complete all as specified and as directed

S&F in repairs 15mm dia brass chromium plated fancy type, hot and cold wall mixer, with telephonic shower and arm, of approved model complete all as specified and as directed

S&F in repairs 15mm dia brass chromium plated fancy type, hot and cold basin mixer, with 450mm long braided hose, of approved model complete all as specified and as directed

S&F 15mm dia bib taps, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed

S&F 15mm dia bib taps, fancy type, long body with wall flanges, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed

S&F in repairs 15mm dia pillar taps, fancy type, cast copper alloy, with capstain heads, chromium plated, screwed down, high pressure, with or without lettered 'HOT'/'COLD', with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed

S&F in repairs brass chromium plated towel ring, 200mm dia, with flange, fixed with chromium plated screws on masonry / tiled wall surfaces including all drilling, etc. complete all as specified and as directed

S&F in repairs brass chromium plated towel rail, 600mm long, with flange, fixed with chromium plated screws on masonry / tiled wall surfaces including all drilling, etc. complete all as specified and as directed

S&F vitreous China bowl urinal flat back half stall of size 465x355x265mm (minimum), white, with grating and union for discharge pipe, including providing fixing plugs, brackets, grating, union and connections to flushing pipe, bedding urinal against wall in CM 1:2, securing bowl with plugs and 60mm long brass screws, pointing around urinal bowl in white cement (excluding flushing cistern, flush pipe and waste pipe), taking down and disposing off old urinal bowl complete all as specified and as directed

S&F wash hand basin, vitreous China, white, flat back type, of size 640x450mm, including CI brackets, cutting for and pinning in ends of brackets with coupling and including PVC connection 60cm key with brass union, fixed as in repairs complete all as specified and as directed

S&F in repairs vitreous China partition, 20mm thick, white, of size 310x700mm fixed with and including suitable stainless steel chromium plated bullet hinges 200mm long, etc. duly gouted in walls complete all as specified and as directed

S&F extended wall hung water closet bowl, cascade type, coloured as approved, with all accessories viz. soft closing seat cover, flushing cistern, with frame, connection to drain or outgoing pipe, and chromium plated mild steel or aluminum anodized hinging device and jointing and connecting up complete all as specified and as directed

S&F soap dish, cast copper alloy, chromium plated, approximate size 160x160x90mm duly fixed on walls with cadmium plated screws complete all as specified and as directed

S&F toilet paper holder, cast copper alloy, chromium plated, approximate size 200mm long duly fixed on walls with cadmium plated screws complete all as specified and as directed

S&F stainless steel kitchen plate rack, of size 1500x1500x300mm fabricated out of 1.0mm thick stainless steel sheet, with separate compartments, cutlery hangers etc. of approved design and type, duly fixed on walls with cadmium plated screws complete all as specified and as directed

S&F in repairs sink with drainage board overall size 915mmx460mm and bowl size 410x330x160mm, made of stainless steel 1mm thick for kitchen with plugs, washer and waste in repairs including in cement mortar to dwarf wall or including fixing cantilever brackets and connection union to pipe complete all as specified and as directed

S&F in repairs chromium plated grating of size 125mm including jointing with solvent cement complete all as specified and as directed

S&F in repairs sheet glass corner shelf assembly consisting of 5.5mm thick sheet glass shelf of size 300x300mm with chromium plated bracket guard and railing 60cm long complete all as specified and as directed

S&F in repairs vitreous China wash down water closet pan (Pedestal pattern), 400x550x200mm dimensions, white colour, with 'P' or 'S' trap, including flush pipe, trap, connection to drain or outgoing pipe, anti-syphonic pipe, white seat cover as approved, closed pattern with flat bottom & cover and chromium plated mild steel or aluminum anodized hinge device and jointing and connecting up complete all as specified and as directed

S&F in repairs vitreous China squatting pan, Orissa pattern of size 580x440mm, white, with integral foot rests and 'P' or 'S' trap, connecting to flushing pipe and trap and making good to the disturbed surfaces in CM 1:3 with finishes to match with the existing complete all as specified and as directed

S&F 10litres capacity PVC flushing tank, syphonic action type, low level, valveless, with PVC inlet ball valve, PVC flush pipe, float, chain and pull and suitable sized brackets including cutting of floor / wall and making good to the disturbed surfaces in CM 1:3 with finishes to match with the existing and taking down of old PVC flush tank and disposing off complete all as specified and as directed

S&F in repairs plastic water closet seat, white / coloured, closed pattern with flat bottom and cover and MS chromium plated or anodised hinging device complete all as specified and as directed

S&F health faucet, telephone type, with CP arms, flexible pipe (ABS body) with 1.0m long PVC tube and wall hook of approved finish complete all as specified and as directed

S&F PTMT jet spray with 1m long PVC tube and wall hook of approved finish for WCs complete all as specified and as directed

S&F in repairs brass, chromium plated shower rose, 75mm size, with 150mm long swivel shower joint, fancy type, including fixing to steel pipe or union 15mm bore complete all as specified and as directed

S&F in repairs 15mm dia ball brass valves, high pressure, with polythene float and flynut, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed

S&F in repairs 20mm dia ball brass valves, high pressure, with polythene float and flynut, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed

S&F in repairs 15mm PVC connections, 600mm long with brass couplings, PTMT nuts, etc. complete all as specified and as directed

S&F in repairs PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement for type 'B' pipes complete all as specified and as directed

S&F PVC (SWR) pipes, 110mm bore, single socketed in any length with rubber ring joints laid in trenches with PVC cowl as required complete all as specified and as directed

S&F PVC (SWR) bends, 110mm dia, ISI marked, any radius with rubber ring joints, etc. complete all as specified and as directed

S&F in repairs UPVC floor trap with PVC grating suitable for 75mm external dia, type B pipes, including jointing with solvent cement complete all as specified and as directed

S&F in repairs razor punched tape concertina coil, 9SWG hot galvanised spring tensile wire of UTS 145 to 150N/sqm, zinc coating 250 to 300gms/sqm, dia of coil when un-streched shall be 610mm having minimum of coil (GI strip) 1.625kg/10Rm, hot dip galvanised razor ribbon tape of size 0.50mm thickness, 19mm wide before wrapping on central core wire fixed with 1.66mm thick GI clips (minimum 25Nos / Rm) and special nut and bolts to hold two coils together and extra rows parallel wire of 10gauge including all necessary staging, T&P for work on perimietr walls, at heights, etc. complete all as specified and as directed

S&F in repairs galvanised 2 strand, steel barbed wire 2.24mm dia, barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails, straining bolts, including securing or tying at crossings with and including provision of galvanised mild steel wire, staples or steel pins, etc. complete all as specified and as directed

S&F in position aluminium-zinc colour coated high tensile alloy steel trap sheeting of 0.5 to 0.53mm thick, high rib, having 550 Mpa yeild strength BMT 0.45mm and zinc (galvanized) and aluminum combined coating of 150 gms/sqm (AZ-150) of 0.50mm TCT having top colour coat of regular modified polyester/silicon modified polyester/HDPE polyester of 18 to 20micron and back coat of 5 to7 micron epoxy primer fixes, RMR 1040 profile width 1125mm in roofing panels / sheeting complete as per manufacturer's instructions, all as specified and as directed Note: The sheet shall be fixed to MS angles with self drilling and self topping screws conforming to AS 3566 with moulded EPDM washers

M&L for Atactic Poly Propaneylene (APP) modified bituminous membrane, weight not less than 4.0kg/sqm, reinforced with non-woven polyester fibre @160gm/sqm by torch method as per manufacturer's instructions complete all as specified and as directed Specifications for membrane: (i) Softening point 150oC minimum (ii) Cold flexibility (-)2oC minimum (iii) Single centre core non-woven polyester reinforcement of not less than 160gm/sqm (iv) Tensile strength of 650N/sqcm and 450N/sqcm in longitudinal and transverse directions respectively (v) Minimum elongation of >20% in both directions (vi) Dimensional stability of 1% maximum (vii) Water tightness / impermiable at 2kgf/sqcm (viii) Water absorption of not more than 1% on mass within 24hrs (ix) Overlaps of minimum 100mm on longitudinal direction and 150mm along transverse direction shall be maintained while laying

M&L for cleaning of internal surfaces of PVC overhead water storage tanks of capacity exceeding 250litres but not exceeding 500litres, including staging (if required), at any position / location, by scrubing the surfaces with the help of coir brush, jute cloth and flushing out all the accumulated mud / silt inside the tank, then applying two coats of lime wash on all internal surfaces like wall, ceiling, floor, etc. and writing tank number, capacity of tank, date of cleaning with white synthetic enamel paint over a black synthetic enemal paint base (of suitable dimensions) with size of letter 4" height complete all as specified and as directed

Puneet Sharma