Extension of Corona Virus Testing Laboratory at PH lab, Thiruvananthapuram.

Amount

EXTENTION OF CORONAVIRUS TESTING LABORATARY AT PUBLIC HEALTH LAB THIRUVANANTHAPURAM

Demolishing existingaluminium partition

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM gasket etc.Aluminium sections shall be smooth, rust free, straight,mitred and jointed mechanically wherever required including cleatangle,Aluminium snap glazing/paneling,C.P.brass/stainless steel screws, all complet as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelingand dash fasteners to be paid for separately).Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12mm thick pre-laminated particle board flat pressed three layer or graded wood particle board conforming to IS:12823 Grade I Type II, in panelling fixed in aluminium doors, window shutters and partition frames with C.P brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-charge.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural of Engineer-in-charge. (Cost of aluminium snap beading shall be drawings and the directions paid in basic item):With float glass panes of 5.50mm thickness

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM gasket etc.Aluminium sections shall be smooth, rust free, straight,mitred and jointed mechanically wherever required including cleatangle,Aluminium snap glazing/paneling,C.P.brass/stainless steel screws, all complet as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelingand dash fasteners to be paid for separately).Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12mm thick pre-laminated particle board flat pressed three layer or graded wood particle board conforming to IS:12823 Grade I Type II, in panelling fixed in aluminium doors, window shutters and partition frames with C.P brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-charge.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural of Engineer-in-charge. (Cost of aluminium snap beading shall be drawings and the directions paid in basic item):with float glass panes of 5.50 mm thickness

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Anodised Aluminium handles 125 mm with plate 175 x 32 mm

Anodised Aluminium butt hinges 100x63x3.2 mm

Anodised Aluminium tower bolt (barrel type) 150x10 mm

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing and fixing up to floor five level precast cement concrete hollow block, including hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering, shuttering complete. 1:1½:3 (1 Cement: 1½ coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size).

12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) sqm

White washing with lime to give an even shade :New work (three or more coats)

Wall Painting with acrylic emulsion paint of approved brand and manufacture to give an even shade two or more coats after applying water thinnable cement primer including the cost of necessary repairs ...etc complete.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :

Structural steel work riveted, bolted or welded in built up sections,trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete Reparing and the extention of the existing shed

Removing the sheet from the existing truss work for laying new sheet

Closing the existing windows with multy wood including all labour and material cost but excluding the cost of painting

Supplying and fixing PVC false ceiling including the cost of frame work and all material cost and laboour cost etc complete

Door Lock

Supplying and fixing Airconditioner including all cost and labour but excluding the cost of stand with manufatures specification

2 Tone Split inverter type

1.5 tone split inverter type

stand for fixing the A/c

Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and roper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer's specifications & direction of Engineer-in-Charge.

Providing and laying polished granite stone flooring in required design and patterns in lenier as well as curvilinear portions of the building, all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm ( average ) thick base of cement mortar 1:4, laid and jointed with cement slury and pointing with white cement slury admixedwith .....

Electrical

Wiring for light point/fan point/exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit , modular switch, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required Group C

Light/fan/calling/5Amps plug point from UPS for computer

Common plug points from KSEB Line

Fan Points

Light points

Supplying and fixing following size modules, PVC box for modular switches in recess etc. as required 6 Module (200mm x 75mm)

Supplying and fixing following size modules, PVC box for modular switches in recess etc. as required 3 Module 100mm x 75mm)

Supplying and fixing following PVC base and cover plate on existing PVC Boxes etc. as required 3 Module

Supplying and fixing floowing PVC switch / socket on the existing PVC plate and switch box including connections but excluding modular plate etc as required 5/6 A switch

3 pin 5/6 A socket outlet

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm

Supplying and drawing 3.5 x 150 sqmm 4 core aluminium cable

Double pole 40 A Change over switch

Cable CAT 6 UTP D-link

Information Outlet CAT -6 D-link

I O box with face plate and key stone

Supplying and installing following size of PVC case and cap joined with connectors bends fixed on wall and ceiling with MS suspenders including bolts and nuts etc as required. 50x 25 mm size

Supplying and installing following size of PVC case and cap joined with connectors bends fixed on wall and ceiling with MS suspenders including bolts and nuts etc as required. 25x 25 mm size

Service and Installation charges

Ceiling fan

B Murugan