Repair to Floor, Plaster, Roof ceiling, joinery, sanitary fittings, Painting, Sewage line, path drain, internal electrification of Mall Road, Young Road under AGE B/R-II of GE Dehradun

Amount

Dismantling of plain or corrugated steel sheeting/ PVC any gauge in roof covering complete all as specified and directed by Engr-in-charge

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-charge

Dismantling timber scantling 40sqcm and over in section and any portion in any portion in framed work complete all as specified and directed by Engr-in-charge

S&F structural steel for roof trusses (framed) , purlins, crane gantries, rails and fastenings and heavy bracket framing (Pipes, Beam, Tee, Angle, Channel or Flat sections) including distance pieces, cleats etc.complete all as specified and directed by Engr-in-charge

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) and removing rubbish off the MD landcomplete all as specified and directed by Engr-in-charge

M&L for 25 mm thick plain cement concrete 1:2:4 type B-1 ( 20 mm graded aggregate) as in sub base of floor complete all as specified and directed by Engr-in-charge

S&F non Skid ceramic tiles 7-8 mm thick(Square/rectangular) area of each tile exceeding o.06 sqm but not exceeding 0.11 sqm in floors e.t.c in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match of coloured tiles over and incl 15 mm thick screed bed in CM 1:6 complete all as specified and directed by Engr-in-charge

Dismantling of floor, hearth or walling including cement mortar bedding (but not backing and removing rubbish off the MD land as directed by Engr-in-charge

S&F ceramic glazed colured/ design tile in vertical surfaces 300x450mmx7mm thick on vertical surfaces such as dado and skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match coloured tiles over and incl 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed by Engr-in-charge

M&L for Double charge Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tile not exceeding 0.36 sqm , in floors etc. laid with tile adhessive and pointed in white or coloured cement to match complete all as specified and directed by Engr-in-Charge

M&L for Double charge Vitrified Ceramic tiles 10 mm thick (square/ rectagular) polished,area of each tiles not exceeding 0.36 sqm , in skirting/dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick plaster in CM 1:4 complete all as specified and directed by Engr-in-Charge

M&L Udaipur green mirror polished stone slab for flooring slabs 12-15mm thick laid over 15 mm thick cement screed bed in CM (1:6) laid and jointed with grey cement slurry mixed with pigments to match the shade of the slab including rounding off exposed edges of stone all as specified including demolition of stone slab and and removing rubbish off the MD land all as specified and directed by Engr-in-Charge

Taking up or down steel tubing 15mm bore and connection incl removal from site as directed by Engr-in-charge

Taking up or down steel tubing 20mm bore and connection incl removal from site as directed by Engr-in-charge

Refixing of old steel tubing 15mm bore, in new or old position with all new fittings to floor, wall or ceiling including cleaning old tubing as directed by Engr-in-charge (Note: Old steel tubing retrived from taking down shall be reused)

Refixing of old steel tubing 20mm bore, in new or old position with all new fittings to floor, wall or ceiling including cleaning old tubing as directed by Engr-in-charge (Note: Old steel tubing retrived from taking down shall be reused)

S&F 15mm bore pipe medium grade galvanised iron with all fittings fixed to wall and ceiling or laid in floor complete all as specified and directed by Engr-in-Charge.

S&F 20mm bore pipe medium grade galvanised iron with all fittings fixed to wall and ceiling or laid in floor complete all as specified and directed by Engr-in-Charge.

Cutting/dismantling carefully with machine cutter existing tiles/flooring to the required portion without disturbing adjoining tiles/flooring and M&L for 12-15 mm thick Granite (of any type) work (table rubbed and polished) in door cill in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed by Engr-in-charge

S&F in repair viterous china squatting pan (orissa pattern) long pan size 580x440mm white with integral footrest with cast iron spun 600 mm long 'P' trap, set in cement concrete type B-1 (1:2:4) complete (excluding flushing cistern and flush pipe) complete all as specified and directed by Engr-in-charge

S&F in repairs vitreous chinaware wash down water closet pan padestal pattern white including fixing bolts, jointing to flushing cistern and flush pipe antisyphonage pipe etc complete all as specified and directed (Make : Hindware/Cera/Parryware).

S&F in repair plastic water closet seat cover white closed pattern with flat bottom and cover and mild steel chromium plated hinging device complete all as directed and directed by Engr-in-charge

S&F in repair vitreous china wash hand basin, white flat back, size 440x550mm including necessary packing, MS brackets all as specified and directed by Engr-in-charge Make: Cera, hindware, parryware

S&F in repairs 32 mm Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and directed by Engr-in-charge

S&F 32 mm High density polyethylene (HDPE) pipes of pressure rating 6 kgf/sq. cm complete all as specified and directed by Engr-in-charge Make: Kisan,

S&F in repair 08 Litr Dual capacity PVC low level flushing cistern including PVC syphon and float valve with PVC long band for out let connection of cistern with WC complete fixing the cistern with wall in pressured connecting with WC complete all as specified and directed by Engr-in-charge (Make commander/ Cera/ Hindware/ pearl).

S&F in repair 15mm bore chromium plated fancy type Short body bib tap of cast copper alloy with capastan head, screwed in iron pipe complete all as specified and directed by Engr-in-charge (Make Jaguar/pearl)

S&F in repair 15mm bore chromium plated fancy type stop valve of cast copper alloy with capastan head, screwed in iron pipe complete all as specified and directed by Engr-in-charge (Make Jaguar/pearl)

S&F in repair Angle cock, brass chromium plated, fancy type, with wall cap with round headed knob, suitable for 15mm bore iron pipe (2 in 1) complete all as specified and directed by Engr-in-charge (Make Jaguar/pearl)

S&F in repair 15mm nominal internal bore PVC connection 450mm long with two brass nuts and PVC washer complete all as specifed and directed by Engr-in-charge

S&F in repair 15mm Chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union complete all as specifed and directed by Engr-in-charge

S&F in repair Brass chromium plated wall mixer (3 in 1) complete all as specified and directed by Engr-in-charge Make: Jaguar Model No CON 281KN, HSH 1929 & OHS 1989/ SHA 477 ES549 ES546 ES547A & ES 531 (Telephone shower)/ Pearl MAR 090 (Wall mixer)HS470 (Hand Shower with tube)SHO 525 (Shower) SH 516 (Arm).

S&F in repair CP central hole basin mixer fancy type single lever 15mm dia all as specified and directed by Engr-in-charge Make : Jaguar ESSCO Model No. DLX 516, Mark: ESSCO ES-516/Pearl Mar 087

S&F in repair brass spindle for bib tap, pillar tap, stop cock,angle valve, wall mixture and basin mixture of any description etc, complete all as specified and directed by Engr-in-charge

Disconnecting existing PVC tanks 1000 ltr at any location/storey and removing from site complete all as specified and directed by Engr-in-charge

S&F triple layer external white 1000 ltrs capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) with threaded cover hoisted and fixed in position all as specified in SSR Part I including 20 mm PTMT float valve with PVC ball complete all as specified and directed by Engr-in-charge

S&F in repairs ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for 20mm bore iron pipe and fixed ( minimum weight 20mm -210 gms) complete all as specified and directed.

S&F in repairs ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for 15mm bore iron pipe and fixed ( minimum weight 20mm -210 gms) complete all as specified and directed.

S&F in repair 32 mm dia PVC waste pipe for WHB and sink 90 cm long with coupler, complete all as specified and directed by Engr-in-charge

Supply and fix in repairs CP grating S/S 304 grade, anti cockroach, 100mm to 125 dia square/round fixed to floor trap with/without hole fixed with cement mortar , complete all as specified and directed by Engr-in-charge

S&F in repairs PVC tank lid/cover threaded with frame fixed with the existing sintex water storage tank lid cover (cylindrical) for 500/1000 ltrs capacity tanks, complete all as specified and directed by Engr-in-charge

S&F in repair 15mm chromium plated brass heath faucet or Jet with all fittings for water closet all as specified and directed by Engr-in-charge

S&F in repair 32 mm Waste fittings/coupling, brass, chromium plated for sinks, basins, etc. with long screwed shanks and fly-nuts complete all as specified and directed by Engr-in-charge

S&F in repair 40 mm Waste fittings /coupling brass, chromium plated for wash hand basin, basins, etc. with long screwed shanks and fly-nuts complete all as specified and directed by Engr-in-charge

S&F in repair sink with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes fittings / coupling including 32 mm waste pipe over and incl beding in cement mortar to dwarf wall or including fixing cantiliver brackets and connecting unoin to pipe overall size 915mm x 460mm bowl size 410mm x330mmx 160mm complete aal as directed

S&F in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste fitting / coupling including 32 mm waste pipe over and incl bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed by Engr-in-charge

S&F in repair Towel Rack with Lower Hanger (Stainless Steel) with hook complete all as specified and directed by Engr-in-charge. Make Jaguar -Cat Part No: AHS-CHR-1581H or equivalent of Cera/Hindustan/Pearl

S&F in repair chromium plated toilet paper holder fixed on wall with PVC Rawal plug complete all as directed Make Jaquar code no-ACN-CHR-1151N or equivalent of Cera/Hindustan/Pearl

S&F in repair stainless steel 304 grade soap dish 150x100 mm fixed with rawl plug complete all as specified and directed by Engr-in-charge

Cleaning of existing PVC/RCC water storage tank with vaccum cleaner machine exc 250 to 500 ltrs capacity with liquid bleach and dry with and apply on coat of anti bacterial spray as directed by Engr-in-charge. Date of cleaning to and CA No to be painted on water storage tank with stencil in black/ white synthetic enamel paint all as directed by Engr-in-Charge.

Cleaning of existing PVC/RCC water storage tank with vaccume cleaner machine 1000 ltrs capacity with liquid bleach and dry with and apply on coat of anti bacterial spray as directed by Engr-in-charge. Date of cleaning to and CA No to be painted on water storage tank with stencil in black/ white synthetic enamel paint all as directed by Engr-in-Charge.

S&F in repairs plate rack size 90 x 100 cm and 200mm deep made out of 1.00 mm thick stainless steel complete all as specified and as directed and directed by Engr-in-charge Make : Prayag/Blue star/ Sliver sine.

Taking down AC / CI / PVC sewage and drain pipes and fittings upto 110mm bore from walls / floors / trenches complete all as specified and directed by Engr-in-charge.

S&F 100mm dia centrifugally cast iron spun (SI-3989-1984) pipe in any length with or with ears, with cement joints laid in trenches or in floors and directed by Engr-in-charge

M&L for 100mm dia centrifugally cast iron spun (SI-3989-1984) soil and waste pipe in any length with or without ears, fixed with cement joints fixed on walls with existing stack clamps complete all as specified and directed.

S&F 75mm dia centrifugally cast iron spun pipe (SI-3989-1984) in any length with or with ears, with cement joints laid in floors. and directed by Engr-in-charge

M&L for 75mm dia centrifugally cast iron spun (SI-3989-1984) soil and waste pipe in any length with or without ears, fixed with cement joints fixed on walls with existing stack clamps complete all as specified and directed.

S&F centrifugally cast iron spun (SI-3989-1984) bends any radius for 100mm dia pipe complete all as specified and directed by Engr-in-charge

S&F centrifugally cast iron spun (SI-3989-1984) bends any radius for 75mm dia pipe complete all as specified and directed by Engr-in-charge

S&F centrifugally cast (spun) iron branch peices, single(equal or unequal) ordinary or inverted (spigot or socket type), or with parrallel branches fitted with oval access doors of 100mm bore dia complete , ISI Marked, fixed in repairs all as specified & directed.

S&F centrifugally cast iron spun (SI-3989-1984) bend (any radius) of 75mm bore with oval access door and directed by Engr-in-charge

S&F 75mm dia centrifugally Cast iron spun (SI-3989-1984) floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed by Engr-in-charge

M&L for 40mm thick cement concrete type A-0, 1:1.5:3 (12.5mm graded aggregate double washed course sand) mixed with water proofing compound finished even and smooth surface without extra cement complete all as specified and directed (Note: Curing shall be carried out with gunny bags. Ponding test shall be carried out and passed by Engr-in-charge after applying the PCC. WPC measured and paid seperately)

M&L for cement concrete in 1:3:6 type C-1 (20 mm graded aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed by Engr-in-charge

Taking down of chowkhat with shutter (without taking off shutter) area n.exc 1.50 sqm each complete all as specified and directed by Engr-in-charge

Taking down of chowkhat with shutter (without taking off shutter) area exc 1.50 sqm & n.exe 4sqm each complete all as specified and directed by Engr-in-charge

Taking out shutters of any description exe 1 sqm and nexe 2Sqm each complete all as specified and directed by Engr-in-charge

Taking out shutters of any description nexe 1 sqm complete all as specified and directed by Engr-in-charge

Taking down, resecuring/repair of wooden shutters of any description exc 1 sqm but n exc 2.0 sqm each and refixing in same opening including painting to match existing surface complete all as specified and directed by Engr-in-charge

Taking down resecuring/repair of any type and refixing in same opening of any description including painting to match existing surface n exc 1 sqm complete all as specified and directed by Engr-in-charge

M&L for 35mm thick, factory made BWR flush shutters, solid core construction, with block board core and plywood face pannels commercial type on both sides including provision of suitable blocks for taking mortice locks, latches or other fittings complete all as specified and directed.

S&F 35mm Factory made second class hard Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, cla-use 8.24 (a); supplied and fitted to chowkats complete all as specified and directed by Engr-in-charge

M&L 30mm thick Factory made 2nd class hard wood glazed and skelton shutter, open rebated and prepared to receive glass gauge etc. devided into squares with plain chamfered or rounded, mitred and rebated sash bars edges of framing pain, chamferd or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section -8 clause 8.24 (b) complete all as specified and directed by Engr-in-charge

M/L 30mm thick Factory made 2nd class hard wood Glazed and skelton shutter, open rebated and prepared to recive glass, gauge etc. (with out sash bar) beads for securing glass etc. sizes of members of shutters as specified in SSR Part-I Section-8 clause 8.24(b) complete all as specified in SSR Part-I and directed by Engr-in-charge

S&F Factory made Steel windows with side hung shutters with box type hinges including steel handle, steel peg stay complete with glazing bars, dovetailed or welded complete all as specified and directed by Engr-in-charge

S&F Factory made Steel windows with side hung shutters with box type hinges including steel handle, steel peg stay complete without glazing bars, dovetailed or welded complete all as specified and directed by Engr-in-charge

Framed work such as grills, gratings, etc.framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed by Engr-in-charge

Taking down existing projected type hings from the steel window carefully without disturbing frame and S&F and fix 50 mm long mild steel box type hinge welded to steel frame and shutter with welding and making good including two coats of synthetic enamel paint over a coat of primer to match the existing surfaces . The work shall be executed at site up to the three storeyed bulding, the rate of scrafholding shall be deemed to be included the quoted rate of this item complete all as specified aand directed by Engr-in-charge

M&L for second class hard wood, plain, solid, straight chowkats & frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed by Engr-in-charge

S&F pre laminated Solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam single piece extruded pvc profile and edgs will be painted to match with prelam sheet,PVC sheet are to be reinforced with 19x19mm MS square tube EPDM rubber gasket weather seal shall be provided through out the frame. The profile shall be mitre cut at two corners and joint by insrting 2 nos of 150mm long backets of 15mmx15mm MS square tube inside the 19mmx19mm MS square tube and suitably screwed and fixing in opening as per specification & drawing.

S&F Factory made pre laminated solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with single piece extruded pvc profile both side prelam PVC sheet 'C' channel having a 5mm thick PVC sheet strip of 20mm width stuck inside with solvent cement, forming stiles, and 5mm thick both side prelam single piece extruded pvc profile for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of both side prelam 5mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with solvent cement complete all as specified and shown on drawing given in SSR Part II. The width of stiles & rails shall be in proportion to the width of the door shutter as given in SSR Part II.

S&F 200 mm long, solid in one piece stainless steel barrel tower bolts of 10mm dia shoot complete all as specified and directed by Engr-in-charge.

S&F 150 mm long, solid in one piece stainless steel barrel tower bolts of 10mm dia shoot complete all as specified and directed by Engr-in-charge.

S&F 250 mm long stainless steel sliding door bolt with hasp, staple (bolt type, dia of bolt 16mm) and fixing clips of sheet, and fixing bolts and sliding bolts of stainless steel and fixed all as specified and directed by Engr-in-charge

S&F 100mm Butt hinges, medium weight, cold rolled mild steel, and fixed and directed by Engr-in-charge

S&F 150mm Stainless steel 304 grade handle complete all as specified and directed by Engr-in-charge

S&F in repair 304 grade Stainless steel wire cloth 8% nickle, 0.50mm nominal dia of wire and and fixed with tinned tacks, or galvanised wire staples complete all as specifed and directed by Engr-in-charge

S&F 304 grade Stainless steel wire cloth cloth 8% nickle, 0.50mm nominal dia of wire and and fixed with tinned tacks, or galvanised wire staples complete all as specifed and directed by Engr-in-charge

S&F 4 mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane with four corner sealed with silicon complete all as specified and directed by Engr-in-charge

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames/steel frame or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specifed and directed by Engr-in-charge

S&F in repair 250 mm stainless steel sliding door bolt 16 mm dia with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed by Engr-in-charge

S&F in repair stainless steel handles 150 mm size all as specified and directed by Engr-in-charge

S&F in repair 150mm long stainless steel toer bolts complete all as specified and directed by Engr-in-charge

S&F in repair 200mm long stainless steel tower bolts complete all as specified and directed by Engr-in-charge

S&F in repair stainless floor door stopper 50mm double legged, complete all as specified and directed by Engr-in-charge

S&F PVC strip with rubber for fixing on bottom of door to prevent insects from bottom of door complete all as specified and directed by Engr-in-charge

S&F in repair stainless steel 202 grade curtain rod 25 mm dia , wall thickness 1mm with bright nickle decorative finnial and fixed to wall with PVC dash fastner complete all as specified and directed by Engr-in-charge . Note : Cost of one pair of side brackets is inclusive in the rate per metre length of curtain rod

S&F factory made PVC flush type shutter of 18mm thickness consisting of panel of PVC profile of 18mm (+ 0.7mm) thick celluka ply of denisity 600kg per cum manufactured by ISO-9000 certified company using for shutter celluka ply 18mm thick and fixed frame. The thickness of shutter is edges painted by matching colour of PVC lining of plain/prelim coloured PVC sheet using etc complete all as specified as per manufacture specification and directed by Engr-in-charge

S&F 30 cm long heavy duty stainless steel telescopic runner & channel for drawers complete all as specified and directed by Engr-in-charge

S&F stainless steel 304 grade semi hydraulic albehari hinges fixed with stainless steel screws all as directed by Engr-in-charge

Taking down cement plaster on brick wall including racking out joints, hacking for key, scrubbing down with water complete all as specified and directed by Engr-in-charge

M&L rendering 15mm thick on fair faces of brick work in CM 1:4 and finished surfaces even and smooth without using extra cement (mixed with water proofing compound where ordered) complete all as specified and directed by Engr-in-charge (Note : WPC measured and paid saperately)

M&L rendering in patches (nexc 3.0 Sqm) 15m thick on fair faces of brick work in CM 1:4 and finished surfaces even and smooth without using extra cement with water proofing compound complete all as specified and directed by Engr-in-charge(Note : WPC measured and paid saperately)

M&L rendering 15mm thick on fair faces of brick work in CM 1:6 and finished surfaces even and smooth without using extra cement (mixed with water proofing compound where ordered) complete all as specified and directed by Engr-in-charge (Note : WPC measured and paid saperately)

Extra over rendering or plastering for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirtings, drip moulds and similar work n exc 15 cm in width or girth; including cutting to edges, all mitres and stopped ends, etc complete all as specified

M&L for preparation of old decorative surface of wall (plastered) by brooming down with coir brush and hand held electrical grinder, scraping down smoke soot, moulds, moss and efflorecent salts and trading oil and grasy spots and finally cleaned with sand paper all as directed by Engr-in-charge

Complete removal of existing treatment of wall upto the plastered surface of wall by brooming down with steel wire brush and hand held electrical grinder, scraping down smoke soot, moulds, moss and efflorecent salts and trading oil and greasy spots and finally cleaned with sand paper all as directed by Engr-in-charge

M&L applying one coat of cement base on old decorated already prepared external surfaces of walls complete all as specified and directed by Engr-in-charge. (Curing shall be carried out before and after application of paint using spray pump manualy operated as directed by Engr-in-charge)

M&L applying two coats of cement base on old decorated already prepared external surfaces of walls complete all as specified and directed by Engr-in-charge. (Curing shall be carried out before and after application of paint using spray pump manualy operated as directed by Engr-in-charge)

M&L for preparation of new surface of wall and applying two coat of cement base paint of wall over a coat of primer complete all as specifed. (Curing shall be carried out before and after application of paint using spray pump manualy operated as directed by Engr-in-charge)

M&L for Preparation of old painted wooden or wood based surface of any description no otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engr-in-charge.

Preparation of old painted steel surface of any desceiption no otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint all as specified and directed by Engr-in-charge.

M&L for applying one coat of oil emulsion distemper on old decorated already prepared surfaces of walls complete all as specified and directed by Engr-in-charge.

M&L for applying two coats of oil emulsion distemper on old decorated already prepared surfaces of walls complete all as specified and directed by Engr-in-charge.

M&L for applying one coat of white wash on old decorated already prepared surfaces of ceiling complete all as specified and directed by Engr-in-charge.

M&L for applying one coat of white wash on old decorated already prepared surfaces of walls complete all as specified and directed by Engr-in-charge.

M&L for preparation of new plastered surface of wall and applying two coat of oil bound distemper over a coat primer complete all as specified and directed by Engr-in-charge

M&L for applying 2-3 mm thick wall care putty exterior grade liquid on wall complete all as specified and directed by Engr-in-charge

M&L for preparation of new plastered / POP / Putty surfaces of walls and applying two coat of exterior emulsion paint over a coat of primer complete all as specified and directed by Engr-in-charge

M&L for preparation of surface and applying 5 to 6 mm POP on wall complete all as specified and directed by Engr-in-charge

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for reinforcement cut as required to facilitate demolition, complete all as specified and directed

M&L for 60 mm thick reinforced precast cement concrete 1:1.5:3 type A-1 (using 20mm graded stone aggregate) as in man hole cover slabs finish fair even and smooth without using extra cement ( Top surface will be chequred finish) including necessary form work, complete all as specified and directed by Engr-in-charge (Note : CA No and Date will be engraved on slab. Reinforcement shall be measured and paid saperately. Curing will carried out with ponding method)

S&F 2mm thick mild steel plain black sheet as in sides of manhole covers and like including two coats of black bituminous paint complete all as specified and directed by Engr-in-charge

S&F TMT MS bars 8 mm dia & over, cut to length, bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including MS wire ( annealed) not less than 0.9 mm dia as specified and directed by Engr-in-charge

Demolition of brick work or stone/boulder, masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but exceeding ashlar facing and pre-cast concrete articles complete all as specified and directed by Engr-in-charge

Brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6 metre means radius built in cement mortar 1:6 complete all as specified and directed by Engr-in-charge

Excavation in trenches not exceeding 1.50 metre wide and not exceeding 1.50 metre depth for foundation, manhole etc not exc 10 Sqm on plan and not exc 1.5 metre in depth including getting out in soft/loose soil complete all as specified and directed by Engr-in-charge

Returning, filling in including spreading, leveling watering and well ramming in layers not exceeding 25 centimetre in soft/loose soil complete all as specified and directed by Engr-in-charge

Surface dressing in soft/loose soil n exc 15 cm deep complete all as specified and directed by Engr-in-charge

Removing excavated surplus soil/material not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and directed by Engr-in-charge

S&F in repair 150 x 150 mm Salt-glazed stoneware gully traps, square or round mouthed, type ‘P’ with grating complete all as specified and directed by Engr-in-charge

Demolition and breaking up drain pipes (slat glazed ware, AC or reinforced concrete) set in cement mortar, in 100 mm internal dia complete all as specified and directed by Engr-in-charge

Salt Glazed Stone Ware drain pipe, grade ‘A’ 100 mm bore dark brown laid in trenches and jointed complete all as specified and directed by Engr-in-charge(Excavation and earth work shall be measured and paid separately).

M&L cement Concrete bed to drain pipes in cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate including packing under and haunching against the sides of pipes after they are laid and tested for 100 mm bore pipe complete all as specified and directed by Engr-in-charge

Plain cement concrete 1:3:6 type C-1 using 20 mm graded stone aggregate as in surface channel, drain and manholes complete all as specified and directed by Engr-in-charge

Plain Cement concrete 1:4:8 type D-2, using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed by Engr-in-charge

Cutting into existing manhole, 150 mm bore pipe, for connecting new drains making good to pipe and removing cutting out existing benching for and forming branch channel in cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregates, smooth finish and re-forming benching complete all as specified and directed by Engr-in-charge

M&L for PCC 1:2:4 Type B-1 using 20mm graded stone aggregate as in benching, coping including necessary form work complete all as specified and directed by Engr-in-charge

Dismantling structural steel work including doors, gates any description complete all as specified.

Removing / cutting trees vegetation, digging out roots from concrete or brick wall, filling holes on building (Block of 4 qtrs) wall / roof / chajja etc applying and making good with epoxy mortar (Asian/Berger) and applying surface treatment to match with existing specifications complete.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, lamp holders, regulators, sockets, light fitting any type etc complete. removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors, etc complete all as specified and directed by Engr-in-charge

M&L for Point wiring with1100 Volts, grade 1.5 Sqmm. (nominal area), PVC insulated but unsheathed multistranded copper conductor single core FRLS cable drawn through and including non metallic medium duty rigid PVC concealed conduit (medium duty) 20mm dia or higher size complete with all accessories such as socket, elbow, junction box, bell mouth, bend, reducer etc including pressed steel juction box of thickness1.2mm for mounting of switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet as top cover, and 1.5 Sqmm. (nominal area) single core FRLS,PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor cable green colour as earth wire upto common earth and connected to earth dolly complete all as specified and directed by Engr-in-charge for the following.

(a) One light /bell / exhaust fan point controlled by one-one way switch.

(b) One ceiling fan Point controlled by one-one way switch through rRegulator.

(c) One three pin 5 Amp socket on same board with other switches.

(d) One three pin 5 Amp socket on independent board.

All as per item No.143.00 here in above but with 2.5 Sqmm. (nominal area) wire/cable for phase and neutral for one 3 Pin 15 amp socket on independent board including one 2.5 sqmm PVC insulated unsheathed multi stranded copper conductor cable, FRLS 1100 volts grade as earth continuity conductor upto common earth & connected to earth dolly complete all as specified and directed by Eng.-in-charge.

M&L for point wiring with1100 Volts, grade 1.5 Sqmm. (nominal area) ,PVC insulated but unsheathed multistranded copper conductor single core FRLS cable drawn through existing steel/PVC conduit etc with 3 mm thick plastic laminated sheet as top cover, and 1.5 Sqmm. (nominal area) single core FRLS,PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor cable green colour as earth wire upto common earth and connected to earth dolly complete all as specified and directed by Engr.-in-charge of following.

(a) One light /bell / exhaust fan point controlled by one-one way switch.

(b) One ceiling fan Point controlled by one-one way switch through regulator.

(c) One three pin 5 Amp socket on independent board.

All as per Item No 145.00 here in above but one three pin 15 Amps switch socket out let on the independent board with 2.5 sq mm PVC insulated FRLS copper conductor and 2.5 Sqmm FRLS copper conductor for continuous earthing complete.

M&L for Point wiring with 1100 Volts grade 1.5 Sqmm (nominal area) PVC insulated but unsheathed multistranded copper conductor single core FRLS cable and 1.5 Sqmm (nominal area) single core FRLS PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor cable green colour as earth wire upto common earth and connected to earth dolly, drawn through and including non metallic medium duty rigid PVC concealed conduit 20mm dia or higher size complete with all accessories such as socket, elbow, junction box, bell mouth, bend, reducer etc complete all as specified and directed by Engr.-in-charge of following. Note:- Wiring shall be terminated in sunken modular boxes. Modular boxes shall be paid under respective items of this BOQ. Wire/cable colour coding shall be maintained properly as per IE rule. (Make of conduit & accessories- Precision/Polycab/AKG, Make of wire- Polycab/L&T/KEI)

(a) One light /bell / Exhaust fan point controlled by one-one way switch.

(b) One ceiling fan/Exhaust point controlled by one-one way switch through regulator.

(c) One three pin 5 Amp socket on same board with other switches.

(d) One three pin 5 Amp socket on independent board.

All as per Item No 147.00 here in above but one three pin 15 Amps switch socket out let on the independent board with 2.5 sq mm PVC insulated FRLS copper conductor and 2.5 Sqmm FRLS copper conductor for continuous earthing complete.

S&F moduler switch piano flush, button type 6 Amp SP one module one way complete all as specified Make : Legrand model Lyncus 6772.00 eqvt in L&T model entice/ Havells model Murano.

S&F moduler switch piano flush button type 16 Amps SP one module one way complete all as specified Make : Legrand model Lyncus Cat No 6772.09 eqvt in L&T model entice/ Havells model Murano.

S&F moduler socket outlet multipurpose 5 Pin 6 Amp two module complete all as specified & directed. Make : Legrand model Lyncus Cat No 6772.28 eqvt in L&T model entice/ Havells model Murano.

S&F moduler socket outlet two in one three pin 6 Amp and 16 Amp two module flush type complete al as specified.Make : Legrand model Lyncus Cat No 6772.30 eqvt in L&T model entice/ Havells model Murano.

S&F moduler bell push 6 Amp one module one way complete all as specified. Make : Legrand model Lyncus Cat No 6772.20 eqvt in L&T model entice/ Havells model Murano.

S&F 4 step modular electronic fan regulator step type 2 module 120 watts 360 degree. Make : Legrand model Lyncus model 6772 41 eqvt in L&T model entice/ Havells model Murano.

S&F in replacement of rusted GI sunken box with flush metal GI box 1/2 module suitable for modular switches incl plastering, making good disturbed surfaces of wall, painting as per existing to match the wall complete all as directed.

All as per item No 155.00 here in above but 3 module.

All as per item No 155.00 here in above but 4 module.

All as per item No 155.00 here in above but 6 module.

All as per item No 155.00 here in above but 8 module.

S&F combind cover plate white 1 module suitable for modular switches. Make : Legrand model Britzy Cat No 6734 91 eqvt in L&T model entice/ Havells model Murano.

S&F combind cover plate white 2 module suitable for modular switches. Make : Legrand model Lyncus eqvt in L&T model entice/ Havells model Murano.

S&F combind cover plate white 3 module suitable for modular switch/socket. Make : Legrand model Lyncus eqvt in L&T model entice/ Havells model Murano.

S&F combind cover plate white 4 module suitable for modular switch/socket. Make : Legrand model Lyncus eqvt in L&T model entice/ Havells model Murano.

S&F combind cover plate white 6 module suitable for modular switch/socket. Make : Legrand model Lyncus eqvt in L&T model entice/ Havells model Murano.

S&F combind cover plate white 8 module suitable for modular switch/socket. Make : Legrand model Lyncus eqvt in L&T model entice/ Havells model Murano.

S&F switch piano flush, button type 5 Amp SP 250 Volt AC complete all as specified & directed.

S&F switch piano flush button type 15 Amps SP 250 Volt AC complete all as specified & directed.

S&F socket outlet multipurpose 3 Pin 5 Amp and 2 Pin 5 Amps 250 V AC complete all as specified & directed.

S&F socket outlet 2-in1,3 pin 5 and 15 Amp flush type 250V AC complete all as specified & directed.

S&F Bell push flush, button type 5 Amp SP 250 Volt AC complete all as specified & directed.

S&F Bell Ding dong 250V AC complete all as specified & directed.

S&F ceiling rose surface bakelite 3 terminals of size 65x25mm. complete .

S&F step type, electronic fan regulator 120 watts, 5 step for ceiling fan 1200/1400 mm sweep 230 volts AC.

S&F lamp holder PVC/polycarbonate type with LED lamp 9/10 watt complete all as specified & directed.

S&F in replacement wall mounted tube light fitting 1x20/22 watts extruded aluminium polycarbonate covers PF 0.9 and above operating voltage 140V-270V colour temp 4000K & lumen input output 95 Lumen per watt and connected to ceiling rose with required length of two core flexible copper cable 23/0.0076 fixed on wall/roof complete all as specified and directed. Make:Wipro Cat part No LL20-281-XXX-65AL1/ Philips cat part No BN021C LED20S PSU CWGR S2/Havells Cat No ENDURA LINEARNEOBS20W LED865SPCWH.

S&F in replacement Decorative Square/Round surface mounted LED flat panel PDC aluminium housing and PMPA diffuser makes it a robust Luminaire 12 Watts PF 0.9 and above operating voltage 150V-300V colour temp 4000K & lumen input output 70 Lumen per watt incl provisioning of 3 core white flexible multistranded copper conductor 23/0.0076 from ceiling rose to light connector complete all as specified and directed by Engineer-in-charge Make : Crompton cat part No LCDN-12-CDL/TL/WW/Wipro cat No LD80-101-XXX-60-XX/Philips Cat No DN092B LED10S-3000-PSU-WH

S&F in replacement of Decorative wall light fixture made up of Polycarbonate, suitable for 15 Watts LED Lamp incl one LED New Odore 10W E27 WW Ball Lamp Lumen output 835 (lm) 3000K complete all as specified and directed by Engineer-in-charge Make : Havells (City-1) cat part No LHDL02160099 (Fitting) LHLDERHEMD8X010(Lamp) or eqvt in Wipro / Philips / Mepro.

S&F in replacement of energy saving Bulk head luminaire with opal diffuser with and including retrofit LED lamp 10 watts complete all as specified and directed by Engr-in-charge. Make : Havells/PhilipsWipro

S&F in replacement mirror light decorative compact luminarious with decorative ends caps 9 Watt or higher LED with all accessories and including connecting up with three core flexible copper conductor cable of suitable size . Make Havells Cat No E-Lite Pride LHEXBLP7IN1W009 or eqvt in Philips/Wipro

Supply and fixing in replacement New generation energy saving and environmental friendly long life LED Street light luminaire Endura Pearl Neo made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP opening seperate driver compartment with IP66 protection and impact resistance of IK07 with separate surge protection 5KA, 40 Watts or near higher size with making all arrangement for fixing light fitting such as replacement of GI pipe bracket made of 40 mm bore medium grade pipe made to shape of 1200 of 70 cm and 50 cm to a overall length of 1.2 mtr for fixing of street light fitting including MS clamps of size 32 x 3 mm flat iron, nuts, bolts and washers of required size painting complete with all necessary electric connection etc all as specified and directed incl taking down the existing unserviceable bldg security light fitting complete all as specified and directed Make : Havells cat part No ENDURAPEARLNEOSL40WLED757PASYTOPC/CG Cat No LSTP-45-CDL / Philips Cat No BRP046 LED 36 CW MR S1 PSU GR /Greenstar DSS 40.

Supply, fixing and Testing in repairs TPN DB VTPN 4 way 415 Volts, 50 Hz indoor type double door Sheet metal enclosure IP-43 DB's flush mounted with 250 Amp Copper busbar for each phase with two neutral bar & two earthbar and cable ties for cable managenment including mounting arrangement for DPX3 MCCB 125 Amps four pole 415 volts as incomer including connection terminal strip complete pre wired with suitable size copper conductor. The DB's should hold type test certificate (CPRI) as per IEC 61439-3 complete all as specified and directed by Engr-in-charge incl taking out Unserviceable DBs, MCCB and MCBs of any capacity, Make: Legrand/L&T/ Indo Asian.

S&F sheet metal enclosures 240 volt with suitable rated bus bar for double door 12 way IP-43 DB's mounting flush on wall/concealed and making good distubed surfaces incl taking out Unserviceable DB any capacity. complete all as specified and directed by Engr-in-charge. Make: Legrand/ L&T/ Indo Asian.

S&F sheet metal enclosures 240 volt with suitable rated bus bar for double door 8 way IP-43 DB's mounting flush on wall/concealed and making good distubed surfaces incl taking out Unserviceable DB any capacity. complete all as specified and directed by Engr-in-charge. Make: Legrand/ L&T/ Indo Asian..

S&F in replacement of MCCB 125 Amps four pole 415 volts thermal magnetic release ICU=100% ICS having breaking capacity 16 KA including connection terminal strip complete all as specified & directed Make:Legrand/ L&T/ Indo Asian.

S&F MCB SPN 240 Volt 10 KA 40 Amp 'C' series conforming to IS complete all as specified & directed. Make: Legrand/L&T/Indo Asian..

S&F MCB single pole 240 volt, 10 KA, 40 Amp, 'C' series confirming to IS complete all as specified and directed. Make: Legrand/L&T/Indo Asian.

M&L for sub main wiring with 2 Single core PVC insulated unsheathed cable 1100 Volts grade heavy duty copper conductor multistranded of size 4 Sqmm (nominal area) drawing in and including 20 mm dia or higher medium duty PVC concealed conduit and conduit accessories and fittings. Including one single core green colour PVC Insulated unsheathed cable copper conductor multistranded of size 4 Sq mm as earth wire upto common earth and connected to earth dolly complete incl taking out old unserviceable submain all as specified & directed.

All as per item No 187 herein above but 2 Single core 6 Sqmm (nominal area) drawing in and including 25 mm dia or higher medium duty PVC concealed conduit incl one 6 Sq mm copper conductor multistranded green colour as earth wire upto common earth and connected to earth dolly complete.

Supply and laying in replacement of u/s XLPE insulated, armoured, heavy duty electric cable, with multi stranded aluminum conductor served with an inner sheathing of PVC type armoured with galvanized steel wire or tape and overall PVC sheathed 1100 Volts grade, nominal cross sectional area 25 Sqmm 4 core incl lugs thimbles bottle timbles and gun metal cable glands and heat shrinkable PVC sleeves on exposed surfaces and teflon tape duly insulated complete laid in trenches, ducts, drawn through pipes across the road/path/along poles/wall/ floors/ equipment etc including jointing and testing complete all as specified and directed by the Engr-in-Charge. Make : Havells/Polycab/KEI

M&L for sand cushioning in trenches for protection of UG cable with river bed sand laid dry in trenches before and after laying of cable, including well ramming and consolidation complete all as specified and directed.

M&L for providing of new sub class 'B' bricks, old size, well burnt laid flat dry for protection of under ground cable complete all as specified and directed.

Supply and laying in replacement of GI Steel tubing medium grade 50 mm (2") dia including all fitting laying in trenches or grouting/fixing in wall for protection of cable complete all as specified and directed by Engineer-in-charge

M&L for replacement of Unserviceable Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground vertically to a depth not less than 2.25 mtr below ground level with top edge of the earth plate at a depth not less than 1.5 mtr below ground level, earth plate surrounded by and packed with a 15 cm thick layer of char coal dust and common salt, earth lead GI wire 4.00 mm. dia by means of bolts, Nuts, Check Nuts and washers of galvanized iron and thimbles and other end of the earth wire connected to main switch board and protected by galvanized iron pipe medium 15 mm. bore, and water pipe 20 mm. bore GI light grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 & 75 mm thick RCC (1:2:4) type B1 cover slab reinforced with 8mm TMT bars 100mm c/c both ways complete all as specified & shown in elect plate No. 3 of SSR part I of 2009 and testing on completion. Note: (i) If the desired earth resistance is not found within permissible limit shall be redone by contractor at no extra cost. (ii) Cost of GI wire 4 sqmm and 15 mm dia pipe medium grade upto 7.5 mtr is included in the rate quoted for this item

S&F in replacement tamper proof electronic single phase whole currrent energy meter (LCD display) 10 Amp to 60 Amp, 240 volt class 1.00 and AC supply including cable connection, proper sealing with barcode with PVC seal. The meter shall comply with the latest version of IS-13779 with at least 2 anti tamper LED indications of line load reversal and earth loading indication including electrical connection with existing system and sealing properly including push fit type transparent meter box . The meter shall work satisfactory with guaranteed accuracy as per limit of IS: 13779. The meter shall be fixed on existing steel boxes on wall complete all as specified and directed. Make:- Secure /L&T/BHEL (Note:- Old unserviceable meter will be deposited to E/M store yard)

S&F Meter Distribution Borard made out of Thermoplastic polycarbonate of size 600x600x170 mm (dust proof & weather proof ,Shock proof, rust proof ,corrosion free ,acid & Chemical resistance ,UV resistance , Halogen free & freerecyclable material) wiyh 230v Ac 50 HZ 3 Wire , Gasket shallbe embedded with T-locking arrangement and suitable for mounting of Electronic Meter -04 Nos incuding electrical connection with exsisting system and sealing properly & taking out u/s broken/rusted box of any size and type complete all as specified and directed. Make Hensel cat part no Mi0800 / Secure/Sintex

Supply only fan capacitor 2.5 mfd complete all as specified and directed make universal / Havells/Epcos .

Supply only fan capacitor 4 mfd complete all as specified and directed make universal / Havells/Epcos

S&F ceiling fan hanging hook clamps (for fixing to ceiling fan rod) made with using GI of suitable size as directed and with heavy duty rubber insulator and two Nos nuts and one bolts including split pin complete all as directed.

Supply and fixing of louvers shutters round or square made out of GI sheet suitable upto 300 mm dia exhaust fan complete incl taking out old u/s complete

Saurav Enterprises

Pal Engineering Services

Asian Builder

Jain Engineering Works

VERDHMAN ASSOCIATES