SPECIAL REPAIR TO BLDG NO P-86 (03 TO 08) SINGLE OFFRS ACCN OF AD REGT AT DHOLEWAL MIL COMPLEX UNDER GE LUDHIANA

Amount

Sch 'A' sec-I

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness ( below or above ground level).

Taking down cement plaster of any description on brick or concrete surfaces etc including racking out joints, hacking for key, scrubbing down with water etc.

Dismantling floor, hearth or wall tiles including cement mortar bedding(but not backing) and removing serviceable tiles to stores and rubbish off the premises.

Taking down chowkats or frames(without taking off shutters from the frame) area exc 1.5 Sqm but n.exc 4.0 Sqm each.Complete all as specified and directed.

Taking down Shutters of any description area exc 1 Sqm but n.exc. 2 Sqm Each,Complete all as specified and directed.

Taking down chowkats or frames(without taking off shutters from the frame) area n.exc 1.5 Sqm each,Complete all as specified and directed.

Hacking out old broken glass (any thickness) , size, quality or description from metal frame including punching or drilling out old glazing pins and providing and fixing new, Complete all as specified and directed. ,ones.Complete all as specified and directed.

Demolition of reinforcement cement concrete as in Roofs, floors (other than ground floors), beams staircases, landing, chajjas, and similar suspended work (reinforcement cut as reqd to facilitate demolition),Complete all as specified and directed.

M& L for reinforced Cement Concrete type B1 1:1.5:3 (M20) (nominal mix ) (using 20 mm graded stone aggregate) in Beams, cantilevers, lintels etc.Complete all as specified and directed.

M&L for reinforced Cement Concrete type B1 1:1.5:3 (M20) (nominal mix ) (using 20 mm graded stone aggregate) in Chajjas etc.

Use and waste rough finished flat Form work to sides and soffits of floor or roof beams, lintels, cantilevers, shelves including supports etc.Complete all as specified and directed.

Use and waste rough finished Form work to edges of concrete floor and roofs and similar work exceeding 5 Cm but not exceeding 10 Cm wide.

M&L for mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips quality.Complete all as specified and directed.

M&L for 25mm thick cement concrete type B-O, 1:2:4 (20mm graded agg ) as in flooring finished even and fair.Complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, approns and laid bedded and pointed in any mortar atc.Complete all as specified and directed.

M&L for machine cut kota stone slab flooring 20-25mm thick over 20mm thick cement screed bed in cement mortar 1:6 laid and jointed with grey cement slurry mix with pigment to match the shade of slab including rubbing and polishing,Complete all as specified and directed.

All as per item No 16 above but in skirting / dado laid over 10mm thick cement screed in CM 1:4,Complete all as specified and directed.

M&L for vitrified ceramic dark shade coloured tiles 8-10mm thick square/rectungular polished area of each tile area not exceeding 0.36 Sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over 15 mm thick screed bed of cm 1:6 complete all as secified.

All as per item No 18 above but as in skirting over rendering 10mm thick in cement mortar 1:4,Complete all as specified and directed.

M&L for glazed ceramic coloured/ printed tiles 450mm x 300mm x 6 to 7mm thick on vertical surfaces as in skirting, dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 10mm thick bedding layer in cement mortar (1:4) including necessary cutting as per site requirement complete all as specified and directed by Engineer-in-Charge.

M&L for 12mm thick rendering on brick work or concrete surfaces in cement mortar 1:6 finsihed the surfaces even and smooth without using extra cement. Complete all as specified and directed.

M&L for rendering 5mm thick in CM 1:3 on fair faces of brick work or concrete surfaces in ceiling, Complete all as specified and directed.

M&L for 15mm thick rendering on brick work or concrete surfaces in cement mortar 1:4 finsihed the surfaces fair and even Complete all as specified and directed.

M&L for preparing newly plastered or pointed surface of wall / ceiling and applying two coats of distemper oil emulsion over a coat of wall care putty complete all asspecified & directed by Engineer-in-charge.

M&L for three coats white wash on ceiling surfaces inclduing prepration of newly plastered and undecorated surfaces.

M&L for two coats of cement base paint including preparation of newly plastered surfaces on walls, Complete all as specified and directed

M&L for 40mm thick cemnt concrete type B-1, 1:2:4 (using 20 mm graded aggregate) as in floorings , finished even and smooth without using extra cement complete all a specified and directed laid in alternate bay.

M&L for 50mm thick PCC 1:3:6 Type C-1 using 20mm crushed stone aggregate as in plinth protection and like finished even and smooth without using extra cement complete all as specified.

S&F for 38mm width of strip glass dividing strips, 3mm thick and inserted in position to confirm to design.

S&F for solid PVC door frame of sixe 50mmx47mm made out of 5mm wood grain printed PVC Sheet reinforced with MS square tube in opening as per specification and drawing.

S&F for factory made soilid panel PVC Door shutter 30mm thick (Stype) consisting of frame made out MS frame shall be covered with heat moulded wood grain printed PVC 'C' channel having PVC sheet stripof 20mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheet used instead of Plain colour PVC sheet & 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm used instead of exposed portion of PVC sheet beading as per specification and drawing.

S&F for pressed steel frames,size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete ,as specified.

S&F for pressed steel frames,size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete ,as specified.

S&F for providing cement concrete type C-0 1:3:6 (12.5 mm graded agg) as for pressed steel chowkhats.Complete all as specified and directed.

S&F for 2nd class 35mm thick hard wood,Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces, and fitted to chowkats.

S&F for 35mm thick first class hard wood Glazed and skelton door shutters , open rebated and prepare to receive glass, gauge etc, size of members of shutters as specifed in SSR part I Complete all as specified and directed.

M&L for two coats of synthetic enamel painting on wooden surfaces over a coat of pink primer including prepration of newly untreates surfaces.Complete all as specified and directed.

S&F for three track powder coated aluminium sliding type window with frame without shash bars,aluminium section weighing not less than 0.55kg/RM including necessary jointing cleats,glazing clips,rubber packing anodised aluminium snap beading screws,etc,Two shutter to be fitted with 5 to 6 mm thick tinted glass & one shutter to be fitted with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aprture 1040mm guide channel at top and bottom with suitable roller including necessary aluminium builders hardware( locking arrangement), Complete all as specified and directed by Engineer-In- Charge.

M&L for painting two coats of synthetic enamel paint including preparation of new steel surfaces of any description over 10cm in width or grith not other wise described. Complete all as specified and directed.

S&F for 150mm aluminium anodised barrel tower bolts of extruded section and fixed.

S&F for 250mm aluminium alloy anodised sliding bolts with hasp, staple and fixing clips of sheet, cast or extruded section fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed.

S&F for butt hinges, 100mm medium weight, cold rolled mild steel.

S&F for 125mm aluminium handles, cast type , anodised.

S&F for galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm.

S&F for galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm in repair.

S&F in repair door helical spring mild steel 300mm, ordinary rat tail rod patteren including roller and roller plate complete.

Demolition brick work or stone/boulder masonary, built in cement mortar or cement lime mortrar incl all qupins, arches, pillars, etc,but incl. ashlar fencings, dressed stone works and precast concrete articles.

M&L for Brick work with sub class B brick straight or curved on plan exc 6 mtr mean radius built in cement mortar 1:6 all as specified and directed.

All as per item No 48 but except bricks

Taking down eaves gutter and rain water pipes (of any size and patern), incl all fittings and, heads, shoes, bends, swan-necks, etc incl cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accesaries)

S&F for 110mm bore PVC (SWR) soil, waste and vent pipe, in any length , with rubber joints, laid in trenches or in floors,Complete all as specified and directed.

S&F for PVC (SWR) 110mm dia bend of any radius.Complete all as specified and directed.

S&F for 18/19mm block boards grade two, interior grade, commercial type with decorative face veneer on both faces and fixed to timber frame work with screws complete all as specified.

Demolition of mud in roofs, any thickness, incl plastering and leeping (whether full thickness removed or only part thereof),Complete all as specified and directed.

Dismantling of brick tiles laid on mud mortar and jointed and pointed in any cement mortar

M&L for PCC( 1:2:4 ) type B-0 using 12.5mm graded stone as in padding on roof correction of slope,Complete all as specified and directed.

Supply only integral water proofing compound.

M&L for cleaning the new plastered surfaces with wire brushes, brooms etc and applying a priming coat of bitumen primer @ 0.30 ltrs/Sqm consisting of 3/4 part bitumen of grade 85/25 and 1/4 part of kerosene oil.Complete all as specified and directed.

M&L for providing APP based polymeric membrane minimum weighing 3Kg/Sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt not less than 150 gms/Sqm ) land on after applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2Kg per Sqm by forced application complete all as specified.

M&L for 40mm thick brick tiles laid on 15mm thick cement mortar 1:6 and joints grouted flush in cement mortar 1:3 mixed with 5% of crude oil by weight of cement,Complete all as specified and directed.

All as above item No.60 but except tiles after clening and removing old mortar from bricks

M&L for flush pointing to brick laid flat or brick tiles in paving cement mortar in 1:3 complete all as specified.

M&L for PCC 1:2:4 type B1 (using 20mm graded stone aggregate) in roof kerbs or mud stops, benching rounded or chamfered on edges complete.

S&F for stop valves 20mm, cast copper alloy, screwed down, high pressure with crutch or butterfly handle etc complete fixed in repairs.Complete all as specified and directed.

Taking up or down steel tubing 15mm bore and connections, including cleaning for refixing or removal to store,Complete all as specified and directed.

All as per item No 65 above but 20 mm bore.

S&F for 15mm GI tubes, medicum grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors.Complete all as specified and directed.

All as per item No 67 but 20mm bore.

Refixing old steel tubing and connections in new or old postion (wall, ceiling , floors ,etc) 15mm bore.Complete all as specified and directed.

All as per item No 69 above but 20mm bore.

S&F for PVC valve less, syphonic action type low level flushing cistern of capacity 10 Ltrs with inlet, ball valve, float and handle and fixed to IWC on existing brackets, fixed in repairs.Complete all as specified and directed.

S&F in repair vitreous china washbasin, white, flat back, size 550 x 400mm, including brackets & incl 32mm bore waste fitting brass, CP for glazed ware basinetc with long screwed shanks and fly-nuts flange end bedded in red lead cement and other end fixed ,Complete all as specified and directed.

S&F for vitreous china coloured wash down water closet pan (pedestal pattern) (excluding fixing bolts, flushing cistern and flush pipe) complete including plastic seat cover, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging devices with recessed bottom, jet spray, etc. Complete all as specified and directed by Engineer-In-Charge. Make : CERA, Jaguar, Hindware.

S&F in repair brass CP wall mixer 3 in 1 system fancy type with including provision of both Handshower and overhead shower complete with 115mm long bend pipe, connecting legs & wall flanges all as specified.

S&F for brass chlorium plated fancy type hand Shower dia 105mm round shape Multi Flow with air effect and fix in repairs,Complete all as specified and directed.

S&F for brass chlorium plated fancy type overhead shower roses, size 150 dia round shape Single flow with self cleaning function incl fixing to steel pipe in repairs,Complete all as specified and directed.

S&F for soap dish, any type, fixed to plugs with chromium plated brass screws in repair complete all as specified.

S&F for brass chlorium plated fancy type single lever Basin Mixer without popup waste with 450mm long Braided Hoses incl fixing to steel pipe in repairs (Make :JAQUAR Cat pt. OPP-15011BPM or equivalent approved by Engineer-in-Charge).

S&F for brass chlorium plated fancy type 2 Way Bib cock with flange incl fixing to steel pipe in repairs ,complete all as specified and directed.

S&F for brass 15mm bore fancy type stop valve/angle valve cast copper alloy chromium plated fancy type screwed down, high pressure, with crutch or butter fly handles fixed in repairs.

S&F for brass C P health faucet with 8mm dia, 1.20 mtr long Flexible tube & wall Hook,complete all as specified and directed.

S&F in repairs brass chromium Towel Ring Round,complete all as specified and directed by Engineer-In-Charge.

S&F in repairs brass chromium plated tubular towel rail, 20mm dia D-type, 60cm long between flange.

S&F for toilet paper holder of CP with SS Flap fixed to walls with chromium plated brass screws,complete all as specified and directed by engineer in charge.

S&F in repair PVC bathroom cabinet mirror size 350mm x 450mm all as specified & directed by Engineer-in- charge

S&F for PVC connections 15mm size with PTMT nuts of lenth 450mm

Supply & fixing for glass self assembly with stainless steel frame Corner glass shelf etc complete all as specified & directed by Engineer-in-charge.

Dismantling water tank & removing to store of capacity exc 250 and n exc 500 Ltr

S&F in repairs Rotational moulded polythylene water strarge tanks 500 ltr (Cylinderical vertical with closed top ) hoisted and fiexed in position all as per specified in SSR Pt-1.

BLANK

S&F for 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed by engr-in-charge.

S&F for 75 mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints, fixed to walls as a vent pipe complete all as specified and directed by engr-in-charge.

S&F for 75 mm bore PVC (SWR) bends any radius complete all as specified and directed by engr-in-charge.

S&F for 110mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by engr-in-charge.

S&F 75mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by engr-in-charge.

M&L for PVC (SWR) floor trap, plain with grating 75mm diameter of outlet, setting and jointing with solvent cement complete.

M&L for endura chequered cement concrete tiles 30cmx 30cmx 10mm thick,set, jointed & pointed in neat cement slurry in floors with grey cement and pigments over & including 20mm thick screed in cement mortar 1:6

Taking down curatain rods along with wooden pelmat laid on wall.

S&F for curtain rod made out of 25mm dia(outer dia )pipe having thickness 0.63mm , PVC coated and colour/pattern, over all dia 28 to 29 mm complete all as specified and directed, Make :- Aerolux/MEC.

S&F for plastic finial of 28 to 29mm bore, decorated type, of any colour/pattern, best quality to suit the curtain rod and fixed at the end of curtain rod with suitable adhesive complete all as specified and directed, Make:- Aerolux/MEC or VISTA

S&F for mild steel prepainted bracket to hold the curtain rod and fixed to wall(Concrete/brick masonry) with the help of 2 Nos 50mm long steel screws and rawl plug included drilling with electric drill and making good the disturbed surfaces complete all as specified and directed.

M&L for one coats white wash on wall undecorated surfaces including prepration of Old plastered surfaces.

M&L for one coats white wash on ceiling undecorated surfaces including prepration surface, plastered or un plastered of Old undecorated surfaces.

M&L one coat of oil bound distemper to old surfaces of walls after preparation complete all as specified.

M&L one coat of cement base paint to old surfaces of walls after prepration complete all as specified.

Taking down carefully the point wiring (light, Fan, socket or power) complete, (incl fittings such as switches, sockets any type, ceiling roses, pandents, light fittings, etc for taking credit( credit for above items should be made as per conditions separately) and making good disturbed surface of walls floors etc. all as specified.

Taking down Ceiling fan, sealing cable end, dismantling blades from fan and keeping in safe custody for reuse at site and making good disturbed surfaces complete all as specified and as directed.

Refixing only ceiling fan and connecting up including provision sutiable of new down rod for ceiling fans,of cable from celling rose/ connector to fan incl painting all as specified and as directed.

M &L Point wiring complete with 1.5 sqmm single core PVC insulted FRLS cable 1100 volts grade multistranded copper conductor drawn through and including 20mm dia PVC rigid non metallic conduit with all accessories such as internal bend end caps etc complete concealed in walls(on surface in ceiling/beam etc.) including provision of 1.5 Sqmm single core PVC insulated FRLS cable 1100 volts grade with multistranded copper conductor cable as earth continuity conductor, all as specified and as directed for the following :-

One light/fan/call bell point controlled by one, one way switch

One switch socket outlet point 5 Amps on independent board

One 3 Pin socket outlet , 5 Amps on the same board with other switch

All as per item No. 109 described here-in-before but with copper conductor cable FR LS 2.5 Sqmm for one 3 pin socket outlet, 15 Amps and including provision of 2.5 Sqmm PVC insulated copper conductor cable as earth continuity conductor on independent board complete all as specified and directed.

Supply and fix for wall decorative LED light fittings 10watt higher energy saving decorative LED lighting fixture enviromental friendly, energy efficient complete all as specified and directed.

Supply and fix for LED tube light fittings 1200 mm, 20W, 240V, 50Hz, higher energy saving decorative ultra slim square profile LED lighting fixture with extruded polycarbonate enviromental friendly, energy efficient complete all as specified and directed.

Supply and fix for LED tube light fittings 600 mm, 10W, 240V, 50Hz, higher energy saving decorative ultra slim square profile LED lighting fixture with extruded polycarbonate enviromental friendly, energy efficient complete all as specified and directed.

Supply & fix for Exhaust fans AC single phase 230/ 240 V of size 300 mm sweep with louver complete all as specified and as directed.

M & L for sub main wiring complete with 2 runs of 6 Sqmm single core PVC insulated FRLS cable 1100 volts grade multistranded copper conductor cable with 1 run of 6 Sqmm single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable as earth continuity conductor, drawn through and including 25 mm or higher dia non metallic rigid PVC conduit and conduit accessories concealed in wall/Ceiling etc all as specified and as directed .

M & L for sub main wiring complete with 2 runs of 4 Sqmm single core PVC insulated FRLS cable 1100 volts grade multistranded copper conductor cable with 1 run of 4 Sqmm single core PVC insulated FRLS cable 1100 volts grade, multistranded copper conductor cable as earth continuity conductor, drawn through and including 25 mm or higher dia non metallic rigid PVC conduit and conduit accessories concealed in wall/Ceiling etc all as specified and as directed .

Supply and fix for sheet metal enclosure with socket plug top and MCB SPN 20 Amp with enclosure with a two pin and earth plug and socket complete all as specified.

Supply and fix for VTPN MCB DB 12 ways ,Double door with 415 Amps, Double door type complete all as specified and as directed .

Supply and fix for MCCB TPN 63 Amp, 415 Volt , C- series, 50 Hz, breking capacity-16 kA complete all as specified and as directed .

Supply and fix for SPN MCB DB 12 ways with 200 Amps rated bus bar 240Volt, Double door type all as specified

Supply and fixing for MCB SPN 40 Amps 240 V, C- curve, 50 Hz, breking capacity-10 kA. complete all as specified and directed.

Supply and fixing for MCB SP 6-32 Amps240 V, C- curve, 50 Hz, breking capacity-10 kA . complete all as specified and directed

Supply and fix for ceiling rose surface type bakelite 65 x 50mm with three terminals complete all as specified and as directed

S&F for switch Modular 6A single pole, one way, 1 module complete all as specified and as directed

S&F for switch Modular 16A single pole, one way, 1 module complete all as specified and as directed

S&F for socket, 6A - 2/3 pin combined 2 module complete all as specified and as directed

S&F for socket 6A/16A - 2/3 pin combined 2 module complete all as specified and as directed

S&F for modular White cover plate with frame,12 module complete all as specified and as directed

S&F for modular White cover plate with frame,8 module complete all as specified and as directed

S&F for modular White cover plate with frame,4 module complete all as specified and as directed

S&F for modular White cover plate with frame,3 module complete all as specified and as directed

S&F for modular White cover plate with frame,2 module complete all as specified and as directed

S&F for modular Metal flush box 12 module complete all as specified and as directed

S&F for modular Metal flush box 8 module complete all as specified and as directed

S&F for modular Metal flush box 4 module complete all as specified and as directed

S&F for modular Metal flush box 3 module complete all as specified and as directed

S&F for modular Metal flush box 2 module complete all as specified and as directed

S&F for bell push single pole AC 230 Volts single pole complete all as specfied and as directed.

S&F for calling bell , AC, 230 Volts, single pole complete all as specified and as directed

S&F for fan step regulator, 120W 2 module complete all as specified and as directed

M &L for earthing incl earth work complete with galvanised steel earth plate electrode 60cm X 60 cm X 6 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level with the top edge of electrode not less than 1.5 mtr below normal ground level connected to galvanised earth lead wire 4 mm dia means of bolts, nuts,check nuts and washers of galvanised iron and GI lead protected with protection pipe of GI light grade 15mm dia upto 3mtr above ground level along poles fixed with two clamps of 25 mm x 3 mm flat iron and connected to running earth wire at top of poles and watering pipe 20mm bore of GI medium grade all as shown in electrical plate No 3 of SSR Part-I 2009 connected to earthing test point all as specified and direct and testing on completion including PCC 1:3:6 ) C-I cover and frame excavation and earth work etc complete all as specified in elect plate No 3 of SSR Part -I 2009 Note :- PCC Chamber shall be constructed at least 1.50 mtr away from on the earth pit electrode and pipe for watering shall be provided in slanting manner.

Taking down of XLPE cable any size complete all as specified and directed.

Supply, laying and testing cable XLPE insulated, screened PVC bedded galvanised steel strip or wire armoured electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of size 50 sqmm 3.5 core complete all as specified and directed.

Excavation in trenches soft/loose soil not exceeding 1.5 m wide and not exceeding 1.5 m deep for laying of pipes/cables etc getting out and bottom surface to required gradient complete all as directed & specified

Returning filling in including spreading leveling watering and well ramming in layers each not exceeding 25 cm thickness complete all as specified and as directed

Removal of surplus spoil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed

Supplying, filling in trenches, spreading, leveling sand cushioning 8 cm below cable and 15 cm above the cable for under ground cable complete all as specified & directed. i.e 18 cm punned down thick shall be considerd for mesurement)

M & L for old size sub class 'B' bricks,laid flat in trenches over the cable with length of brick perpendicular to the direction of the cable , adjacent/abutting each other complete all as specified

Taking down of any size of bldy security light fittings complete all as specified and directed.

Supply and fixing bldg security light fitting LED 30 W LED made up of pressure die cast aluminium housing with potted isolated driver and high power LED and indl lenses, oprating range- 90V to 340V AC. IP66 with high power LED lamp incl with suitable size of bracket compete all as specified and directed.

ANUJ ABROL CONTRACTOR

CHOUDHARY ENTERPRISES

SHRI GANESH CONSTRUCTION CO.

M/s G N Const. Co.