CO Water Supply Scheme in village Satohal in GP Sehli in Tehsil Sadar Distt Mandi HP

Amount

Excavation in Foundation and trenches in eart work upto all depth in all kinds of soil such a pick work jumper work, blasting work, chisellin of soft / hard rock where blasting is prohibited i all leads and lifts and including trimming of side levelling of bed to correct grade stacking th excavated soil in 15 cm. layers when require into plinth sides of foundation includin consolidating each deposited layer by rammin and watering and then disposing oof all surplu excavated soil as directed in all leads and lif and soring/strutting timbering and dewatering where ever required to the entire satisfaction the Engineer-in-Charge.

Providing and laying cement concrete 1:3:6(1cement:3 sand:6 graded stone agg. 40mm nominal size) and curing complete excluding cost of form work in foundation and plinth in all leads and lifts.

Providing and laying cement concrete 1:1.5:3(1cement:1.5 sand:3 graded stone agg. 20mm nominal size) and curing complete excluding cost of form work in foundation and plinth in all leads and lifts.In Foundation and plinth.

in walls (any thickness but not less than 0.1 mm thichness ) attached pilatsters , butteresses , plinth and string courses etc. from top odf foundation level up to floor two level.)

P/L RCC Work 1:2:4 (1 cement: 2 course sand :4 graded stone aggregete) 40 mm thick nominal size and curring complete excluding the cost of form work and reinforcement in:- Suspended floors, roofs landings and shelves and their supports balconies beams girders. bressumers and cantilivers up to floor two level.Suspended floor floors , landings and shelves and their supports, balconies, beams ,girders ,bressumers and cantiliver up to floor two levels.

Providing form work with steel plates 3.15mm thick welded with angles iron in frame 30x30x5mm so as to give a fair finish including certring shuttering strutting and propping etc. with wooden battens and ballies height of propping and centring below supporting floor to ceiling not exceeding 4 mtrs and removal of the same for in-situ reinforced concrete & plain concrete work in all leads and lifts in:- Flat surfaces such as soffits of suspended floors roofs landings and the like floors etc up to 200 mm in thickness.

Vertical surface such as walls (any thickness) partitions and the like including attached pillasters buttresses, plinth and string courses and the like complete in all respects with in all leads & lifts as per directions of Engineer-in-Charge.

Providing & laying tor steel reinforcement for RCC work including bending, binding and placing in position complete indluding the cost of binding wire in all leads and lifts upto floor two level in all leads and lifts.

Providing and fixing SFRC Manhole cover for frame if internal size 560 mm dia with frame (Midium) with in all leads and lifts(Weight of cover & frame not less than 100 Kg)

Laying, jointing and testing of GMS tube in trenches (light grade) of following dia meter including providing and fixing tube fitting such as bends, tees, air valves, unions and collars etc. including carraige of GI pipes as per direction and to the entire satisfaction of the Engineer-in-charge (earth work in trenches to be measured and paid for separately) in all leads and lifts. Inlet pipe 32 mm diameter (LC)

Outlet pipe 25 mm diameter (LC)

Scour pipe 50 mm diameter (LC)

Vent pipe 100 mm diameter (LC)

Providing and supplying of Brass Wheel valves (Medium pattern) screwed femail ends , screwed in-bonnel inside screw non rising stem, integral seats & hard wheel operated , diameter mentioned below in all lead and lifts and to the entire satisfaction of the Engineer-In -Charge. Inlet pipe 32 mm diameter

Outlet pipe 25 mm diameter

Scour pipe 50 mm diameter

Proviidng and fixing of MS Wheel valve chamber of size 450*450*450 mm made of 2.00 mm thick MS sheet with MS Angle 35*35*4 mm thick also providing extra length of 250 mm of same angle (As tee)in the bottom of four legs for embdded in cement concrete and top opening will provide with hinges with locking arrangements providing hole on three side of hamber for crossing of different size of pipes complete etc. The hight of wheel valve chamber not less than 600 mm inclding cutting welding, painting with lead Red Oxide paint complete in all respect and as per satisfaction of Engineer-in-charge.

Providing, Manufacturing, Supplying and Fixing of Fencing Panel of Size. 1.20 M X1 20 Meters fitted with Expended Metal Jali 25 X 25 mm mesh welded with M.S. angles for stand 40 x 40 x 5 MM including cutting, welding, painting with red oxide paint complete in all respect and as per with MS flat cover 25 X 5 MM M.S. hold fast made of M.S. angle 40 x 40 x 5 MM mesh panel of size 1.20 X 120 M fitting with expended metal mesh embended in cement concrete Pillars complete in all respect as per direction and to the entire satisfaction of the Engineer-in-Charge.

Rajesh Kumar (BID ID -502809)

Raj Kumar Prop R.K. Construction (BID ID -502816)