E.T.No.-EDC(USN)36/2025-26

Amount

Annexure-A (LABOUR CHARGES)

Earthing of distribution transformer including digging of pit of size 2.5 Mtr depth and make hole of size 150 mm. Placing of earthing electrode, connecting the same with G.I. Strip of size 35x6 mm for a minimum lenght 6 m. treatment of soil with highly condctive substance as per IS 30343 complete in all respect, result of earthing resistance to be recroded in M.B. before and after installation of earthing. The earth resistance after earthing should be less than 1 Ohm.

Fabrication of MS Channel angle iron etc in required sizes with drilling of holes upto good finish for top channel, bracing and special type bracket etc. as per RESPO schedule and local approved drawing.

Excavation of earth for stay pit of size 0.6x0.6x1.2 mtr in all types of soil including proper dressing of sides and ramming of bottom including getting out the excavated soil and disposal of surplus excavated soil as directed complete work

Fixing, tightening and nozzling of stay with pole and stay rod on required tension as per drawing/manual in 11 KV line

Grouting of Stay in size 0.6x0.6x0.3 in CC ratio 1:4:8 (1 cement : 4 graded stone 20mm nominal size : 8 coarse sand ) block including cost of Cement, sand and stone ballast back filling of soil and boulders in pit and ramming and proper alignment, leveling as per RESSPO Manual.

Excavation of earth for pole pit of size 0.9x0.6x1/6 of full length of pole for erection of pole in all types of soil including proper dressing of sides and ramming of bottom including etting out the excavated soil and disposal of surplus excavated soil as directed complete work

Erection of PCC single support pole in proper level and alignment along with fixing of all accessories like top channel & clamps as per RESPO manual

Erection of SP-55 single support pole in proper level and alignment along with fixing of all accessories like top channel & clamps as per RESPO manual

Erection of SP-72 single support pole in proper level and alignment along with fixing of all accessories like top channel & clamps as per RESPO manual

Erection of PCC double support pole in proper level and alignment along with fixing of all accessories like top channel, X bracings & clamps as per RESPO manual.

Erection of Sp-55 double support pole in proper level and alignment along with fixing of all accessories like top channel, X bracings & clamps as per RESPO manual.

Erection of Sp-72 double support pole in proper level and alignment along with fixing of all accessories like top channel, X bracings & clamps as per RESPO manual.

Erection of SP-72(11KV/33 KV) four pole support pole in proper level and alignment along with fixing of all accessories like top channel, X bracings & clamps as per RESPO manual.

Grouting of pole in size 0.45x0.45x1/9 of the support in CC ratio 1:4:8 (1 cement:4 graded stone20 mm niminal size: 8 coarse sand) block including cost of cement, sand and stone ballast back filling of soil and boulders in pit and ramming and proper alignment, levelling as per RESPO cnstruction manual

Muffing of poles size 0.45x0.60 cm radius with 1:3:6 (1 cement:3 coarse sand :graded stone 10 mm nominal size) block size 45 cm height from ground level including cost of cement,stone and sand etc

Dismantling of existing LT/HT line. including disc fitting, Insulator, clamps, Nut & Bolts and consumer connections and Street light connections etc. including rolling of conductor and cartage back from site to JE store (PCC Single Pole).

Dismantling of existing LT/HT line. including disc fitting, Insulator, clamps, Nut & Bolts and consumer connections and Street light connections etc. including rolling of conductor and cartage back from site to JE store(SP-33 Single Pole).

Dismantling of existing LT/HT line. including disc fitting, Insulator, clamps, Nut & Bolts and consumer connections and Street light connections etc. including rolling of conductor and cartage back from site to JE store(SP-55 Single Pole).

Dismantling of existing LT/HT line. including disc fitting, Insulator, clamps, Nut & Bolts and consumer connections and Street light connections etc. including rolling of conductor and cartage back from site to JE store(PCC Double Pole)

Dismantling of existing LT/HT line. including disc fitting, Insulator, clamps, Nut & Bolts and consumer connections and Street light connections etc. including rolling of conductor and cartage back from site to JE store(SP-55 Double Pole)

Dismantling of existing LT/HT line. including disc fitting, Insulator, clamps, Nut & Bolts and consumer connections and Street light connections etc. including rolling of conductor and cartage back from site to JE store(SP-55 four Pole).

Dismantling of existing HT line. including disc fitting, Insulator, clamps, Nut & Bolts and consumer connections and Street light connections etc. including rolling of conductor and cartage back from site to JE store(ACSR Weasel).

Dismantling of existing HT line. including disc fitting, Insulator, clamps, Nut & Bolts and consumer connections and Street light connections etc. including rolling of conductor and cartage back from site to JE store(ACSR Dog).

Dismantling of Transformers from double pole /plinth including opening of all connections, circuts & earthing strip etc. (25 KVA).

Dismantling of Transformers from double pole /plinth including opening of all connections, circuts & earthing strip etc. (100 KVA).

Dismantling of Transformers from double pole/plinth including opening of all connections, circuts & earthing strip etc. (250 KVA).

Dismantling of Transformers from double pole/plinth including opening of all connections, circuts & earthing strip etc. (400 KVA).

Dismantling of stay set complete.

Dismantling of guarding in LT Line.

Painting of SP-55 pole with angle and channel and all steel part by one coat of Red Oxide Primer and two coats of aluminium Paint and two strip of fluorescent altemate Red and White paint 30 Cm wide upto 1.5 Mtrs. From ground level.

Painting of SP-72 pole with angle and channel and all steel part by one coat of Red Oxide Primer and two coats of aluminium Paint and two strip of fluorescent altemate Red and White paint 30 Cm wide upto 1.5 Mtrs. From ground level.

Excavation of earth of size 2.1x2.1x1.2 meter for DTR Plinth.

Cement concreting work in ratio 1:4:8 for DTR Plinth.

Brick work in 1:4 ratio for DTR Plinth.

RR massonary work in 1:6 ratio for DTR Plinth.

RCC Work of 1:2:4 ratio 15 cm thickness for DTR Plinth.

Cement Plaster on side walls in 1:4 ratio on DTR Plinth.

Installation/mounting of new 100 KVA Tranformer on pole structure and fixing of channel /angle etc. and making all connections of HT and LT side and its complete commissioning.

Installation/mounting of new 25 KVA Tranformer on pole structure and fixing of channel /angle etc. and making all connections of HT and LT side and its complete commissioning.

Installation/mounting of new 400 KVA/500 KVA Tranformer on plinth structure and fixing of channel / angle etc. and making all conn ections of Ht and LT side and its complete commissioning.

Installation/mounting of new 250 KVA Tranformer on plinth structure and fixing of channel / angle etc. and making all connections of Ht and LT side and its complete commissioning.

Mounting & Fixing of Fuse sets on double pole structures including making of connections complete work.

Laying, Spreading, Stringing and sagging of 11 KV /33 KV line in 3 phase (3 Phase 3 wire) of ACSR Weasel as phase wire with G.I. earth wire complete including fixing of all accessories in 3 Nos. conductor in parallel with binding and jumpering as per profile and profile and sagging chart.

Laying, Spreading, Stringing and sagging of 11 KV / 33 KV line in 3 phase (3 Phase 3 wire) of ACSR Dog as phase wire with G.I. earth wire complete including fixing of all accessories in 3 Nos. conductor in parallel with binding and jumpering as per profile and profile and sagging chart.

Guarding of LT/11 KV Line over (Telephone / Road/L.T. line crossing as per drawing with 6/8 SWG G.I. wire including fixing of guarding channel/ angle as per RESSPO manual.

Route cleareance by cutting of tree branches / proning, loping and chopping of trees for L.T., 11 & 33 KV line.

Fixing of Danger Board and number plate complete by providing clamps of M.S. Flat 50x6 mm and Nuts & Bolts, danger Boards of M.S. Sheet 2 mm Thick 11''x7'' size (Including cost of all material).

Cartage of PCC Poles from store centre to construction site with loading, unloading at both points and proper stacking.(Distance 21- 50 Km)

Cartage of ST pole SP-55 Poles from store centre to construction site with loading, unloading at both points and proper stacking.(Distance 21-50 Km)

Cartage of ST pole SP-72 Poles from store centre to construction site with loading, unloading at both points and proper stacking.(Distance 21-50 Km)

Cartage of other material (other than poles) by vehicle from Store Center to nearest construction site Store including loading and unloading at both ends(distance 21-50 Km)

Headload cartage of PCC Pole from road to site (distance 0-1 Km)

Headload cartage of ST Pole SP-55 from road to site (distance 0-1 Km)

Headload cartage of ST Pole SP-72 from road to site (distance 0-1 Km)

Head load cartage of small material (distance 0-1 Km)

Headload cartage of 25 KVA transformer from road to site(distance 0-1 Km)

Headload cartage of 100 KVA transformer from road to site(distance 0-1 Km)

Headload cartage of 250 KVA transformer from road to site(distance 0-1 Km)

Headload cartage of 400 KVA transformer from road to site(distance 0-1 Km)

Dismantling of Fencing and Gate of S/S including fabrication cutting and welding works at 33/11 KV Sub Station.

Re-erection of fencing and gate complete all work.

Laying Sagging of LT XLPE AB CABLE 3X120+1X95+1X16 Sq.mm

Service of Hydra Machine for Lines and Transformer related work because of busy traffic in Town area for safety purpose.

Back Cartage of Petty material, 0-20 Km.

Laying and Stringing of HT XLPE Cable with the help of appropriate size of conductor /Steel wire (conductor & steel wire Should bear the load of cable having 5% sag ) including supply of MS clamp and insulated clamp to support cable on support wire & Pole.

Dismentaling of existing fuse set.

Fixing of Channel, Angle on Pole.

Disconnection and Reconnection of service connection single phase.

Disconnection and Reconnection of service connection three phase.

Providing and Fixing of 11 KV XLPE cable Jointing Kit Outdoor 3x70 sqmm

Dismental & Re-erection of LT ACB Panel.

Dismental & Re-erection of LT PRMC.

Back Carriage of Scrap material.

Dismantling Plinth & Cable Hardware.

Painting of Fuse set Structure.

Annexure-B (SUPPLY ITEMS) (As per UPCL Specifications)

Supply of Holding Clamp for Gaurding

Supply of Holding Clamp J-I Hook for AB Cable

Supply of PG Clamp for Weasel to Weasel.

Supply of Nut & Bolts

Supply of Holding Clamp for PCC Pole.

Supply of F-Clamp

Supply of Stay Clamp for SP-72 with N/B

Supply of Suspension Clamp.

Supply of Dead End Clamp for AB Cable.

Supply of Stay Clamp for PCC Pole.

Supply of HT Stay Insulator.

Supply of Danger Board.

Supply of Insulated PRC (IPC 95-95 Sq.MM)

Supply of PG Clamp for Dog to Dog.

Supply of Earth Clamp Off size.

Supply of Piercing Connector 120 to 35 Sq.MM

Supply of Connector 95-35 Sq.MM

Supply of SMC Three Phase L.T. Distribution Box with inbuilt panal lock, Al bus bar RYB 25x6mm., Al Busbar N. 40x6mm. for connection of L.T. consumer (Sintex make or other ISI mark reputed company ) with Panel Lock with key).

Supply of Stay Clamp for SP-55 with Nut & Bolt.

Supply of PRC 120-120

Supply of Shear Head Type IPC 70-70 Sq.MM

Supply of Distribution Box Clamp.

Supply of AL. Crimping Type Lugs 70 Sq.MM

Supply of AL. Crimping Type Lugs 630 Sq.MM

Supply of AL. Crimping Type Lugs 400 Sq.MM

Supply of AL. Crimping Type Lugs 240 Sq.MM

Suppply of Tinned Copper Fuse Wire 20 SWG.

Suppply of Tinned Copper Fuse Wire 18 SWG.

Suppply of Tinned Copper Fuse Wire 22 SWG.

Suppply of Tinned Copper Fuse Wire 16 SWG.

M/S GURU NANAK ENTERPRISES (BID ID -405445)

MANRAJ ELECTRICAL & INFRASTRUCTURE (BID ID -405507)