Revitalization of Subhash Park, Kochi, Ernakulam District

Play and GYM Area

2.31 Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared

2.8.1 Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

5.33.2.2 Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage mfor all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All work above plinth level upto floor V levelConcrete of M30 grade with minimum cement content of 350 kg /cum

5.22.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

OD198265/2025-2026 Supplying and filling fine sand in play area as per the specification required.

16.69 Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature jointed with cement mortar 1:3 ( 1 cement : 3 coarse sand) , including making joints with or without grooves ( thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge ( length of finished kerb edging shall be measured for payment ). ( Precast C.C. kerb stone shall be approved by Engineer-in-Charge)

OD198323/2025-2026 "Supply and Fixing of 25 MM EPDM including cost of materials, tools and labour complete.: Providing & Laying of EPDM (Ethylene Propylene Diene Monomer) Safety & Sports total 25MM [ 19 MM SBR & 6 MM EPDM ] thick Rubber flooring systems comprising two layers with the top layer of 6mm being high quality EPDM granules and the bottom layer being 19 mm SBR. The EPDM granules shall be mixed on site with specially developed binders and trowelled by hand to specified thickness creating a seamless surface. The flooring system shall be hygienic, durable with high elasticity, all weather, resilient, non slip, high impact and easy maintenance EPDM. We have two types of EPDM granules , SR 5560 & SR 6065 for the sports and recreational market. EPDM granules shall be resilient to both outdoor weathering and UV exposure, have high durability and suitable for running track applications. The performance requirements and test methods for impact absorbing playground surfacing shall comply with SS 495:2001 or ASTM Standards. "

OD198633/2025-2026 Supplying of Cement Polo Seater 210 cm Diameterx45 cm Height (set of five sections) including cost of all materials, transportation complete.

OD198637/2025-2026 Supply and applying of Anti-Skid Stone Crete Flooring thickness: 20 mm including cost of materials, tools and labour complete.

OD198650/2025-2026 Supply and Fixng of Bicycle including cost of materials, tools and labour complete.: All products must tested and certified to meet EN16630 safety standards with GS test mark. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The GS mark-EN 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors. The EN16630 & GS Mark certificates must reflect clearly on the notified certifying bodies websites. All products must clearly display the GS mark as has been issued in the EN16630 safety certificates. Upright structural posts of height 1.31 m is to be schedule HOT DIP Galvanized steel with a 60 mm O.D. and 2.2mm (wall) thickness of the tubing. Two numbers of Pedal of size 113mm x 40mm & Rotating Disc of Dia 380 mm fabricated from 40 O.D. galvanized steel pipes. The poles are welded on to a base plate made from steel with 114mm inner diameter. Welded. Bearings : Maintenance-free ball bearings. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. The limiters must be in accordance with EN16630 safety norms. Scope of delivery : 1 completely pre- assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. EQUIPMENT DIMENSIONS: 1.11m x 0.51 m x 1.31 m

OD198663/2025-2026 Supply and Fixng of Big Shoulder Wheel including cost of materials, tools and labour complete.: All products must tested and certified to meet EN16630 safety standards with GS test mark. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The GS mark-EN 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors. The EN16630 & GS Mark certificates must reflect clearly on the notified certifying bodies websites. All products must clearly display the GS mark as has been issued in the EN16630 safety certificates. Upright structural posts of height 1.47 m is to be schedule HOT DIP Galvanized steel with a 114mm O.D. and 2.2mm (wall) thickness of the tubing. Circular Handrail of Dia 0.69 m and Dia 42 mm fabricated from 42 O.D. galvanized steel pipes. The poles are welded on to a base plate made from steel with 114mm inner diameter. Bearings : Maintenance-free ball bearings. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. The limiters must be in accordance with EN16630 safety norms. Scope of delivery : 1 completely pre- assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. Including installation and freight charges. EQUIPMENT DIMENSIONS: 0.69 m x 0.61 m x 1.94 m

OD198679/2025-2026 Supply and Fixing of Double Air Skier including cost of materials, tools and labour complete.: All products must tested and certified to meet EN 16630 safety standards with GS test mark. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The GS mark-EN 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors. The EN 16630 & GS Mark certificates must reflect clearly on the notified certifying bodies websites. All products must clearly display the GS mark as has been issued in the EN 16630 safety certificates.Upright structural posts of height 1.25 m is to be schedule HOT DIP Galvanized steel with a 114mm O.D. and 2.2 mm (wall) thickness of the tubing. Foot rest of size 365 mm x 164 mm and Standing Bars of length 1640 mm x 40 mm fabricated from 40 O.D. Galvanized steel pipes. Lower part of Support Handrails of size 0.8 m high and Dia 47 mm and Upper part of Support Handrails of size 0.51 m high and Dia 32 mm fabricated from 47 mm O.D. and 32 mm O.D. The poles are welded on to a base plate made from steel with 114 mm inner diameter. An Internal limiter prevents the equipment from moving uncontrollably. Bearings : Maintenance-free sealed ball bearings. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. The limiters must be in accordance with EN 16630 safety norms. Scope of delivery :1 completely pre- assembled equipment modules. Maintenance : Maintain according to EN 16630 and the maintenance guide. EQUIPMENT DIMENSIONS: 1.61 m x 0.50 m x 1.50 m

OD198707/2025-2026 Supply and Fixng of Seated Chest Press including cost of materials, tools and labour complete.: All products must tested and certified to meet EN16630 safety standards with GS test mark. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The GS mark-EN 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors. The EN16630 & GS Mark certificates must reflect clearly on the notified certifying bodies websites. All products must clearly display the GS mark as has been issued in the EN16630 safety certificates. Upright structural posts of height 1.88 m is to be schedule HOT DIP Galvanized steel with a 114mm O.D. and 2.2mm (wall) thickness of the tubing. Two pair of U-Shaped Bars of 1.02 m and Dia 40 mm while the handles are placed at a spacing of 698 mm fabricated from 40 O.D. galvanized steel pipes. The poles are welded on to a base plate made from steel with 114mm inner diameter. Bearings : Maintenance-free ball bearings. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries.The limiters must be in accordance with EN16630 safety norms. Scope of delivery : 1 completely pre- assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. EQUIPMENT DIMENSIONS: 1.82 m x 0.69 m x 1.88 m

OD198757/2025-2026 Supply and Fixng of Self Weighted Rower including cost of materials, tools and labour complete.: All products must tested and certified to meet EN16630 safety standards with GS test mark. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The GS mark-EN 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors. The EN16630 & GS Mark certificates must reflect clearly on the notified certifying bodies websites. All products must clearly display the GS mark as has been issued in the EN16630 safety certificates. Horizontal bars of length 1.26 m is to be schedule HOT DIP Galvanized steel with a 60mm O.D. and 2.2mm (wall) thickness of the tubing. Handle Bars of 0.74 m and Dia 38 mm fabricated from 40 O.D. galvanized steel pipes. The poles are welded on to a base plate made from steel with 114mm inner diameter. Bearings : Maintenance-free ball bearings. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. The limiters must be in accordance with EN16630 safety norms. Scope of delivery : 1 completely pre- assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. EQUIPMENT DIMENSIONS: 1.26 m x 0.80 m x 1.59 m

OD198767/2025-2026 Supply and Fixng of Arm and Pedal Bike including cost of materials, tools and labour complete.: All products must tested and certified to meet EN16630 safety standards with GS test mark. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The GS mark-EN 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors. The EN16630 & GS Mark certificates must reflect clearly on the notified certifying bodies websites. All products must clearly display the GS mark as has been issued in the EN16630 safety certificates. Horizontal Structural post of length 1.10 m supporting Upright structural posts of height 1.23 m and Dia 60mm is to be schedule HOT DIP Galvanized steel with a 114mm O.D. and 2.2mm (wall) thickness of the tubing. Pedals of size 108 mm & Bars of size 197 mm. The poles are welded on to a base plate made from steel with 114mm inner diameter. Bearings : Maintenance-free ball bearings. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. The limiters must be in accordance with EN16630 safety norms. Scope of delivery : 1 completely preassembledequipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. EQUIPMENT DIMENSIONS: 1.43 m x 0.65 m x 1.23 m

OD199494/2025-2026 Supply and Fixng of Waist Twsiter including cost of materials, tools and labour complete.: All products must tested and certified to meet EN16630 safety standards with GS test mark. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The GS mark-EN 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors. The EN16630 & GS Mark certificates must must reflect clearly on the notified certifying bodies websites. All products must clearly display the GS mark as has been issued in the EN16630 safety certificates. Upright structural posts of height 1.35 m is to be schedule HOT DIP Galvanized steel with a 114mm O.D. and 2.2mm (wall) thickness of the tubing. Circular Handrail Dia 42 mm fabricated from 42 O.D. galvanized steel pipes. The poles are welded on to a base plate made from steel with 114mm inner diameter. An Internal limiter prevents the equipment from moving uncontrollably.Bearings : Maintenance-free ball bearings. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. The limiters must be in accordance with EN16630 safety norms. Scope of delivery : 1 completely pre- assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. Equipment Dimensions: 1.44 m x 1.29 m x 1.35 m

OD199514/2025-2026 Supply and Fixng of Mini Ski including cost of materials, tools and labour complete.: All products must tested and certified to meet EN16630 safety standards with GS test mark. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The GS mark-EN 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors. The EN16630 & GS Mark certificates must reflect clearly on the notified certifying bodies websites as online verification is mandatory during technical bid. All products must clearly display the GS mark as has been issued in the EN16630 safety certificates. Upright structural posts of height 1.40 m is to be schedule HOT DIP Galvanized steel with a 114mm O.D. and 2.2mm (wall) thickness of the tubing. The Standing Bars 991 mm and Dia 60 mm fabricated from 40 O.D. galvanized steel pipes Upper part of Support Handrails of size 1.04 m high and Dia 38 mm fabricated from 40mm O.D. and 32 mm O.D. galvanized steel pipes. The poles are welded on to a base plate made from steel with 114mm inner diameter. An Internal limiter prevents the equipment from moving uncontrollably.Bearings : Maintenance-free ball bearings. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. The limiters must be in accordance with EN16630 safety norms. Scope of delivery : 1 completely pre- assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. EQUIPMENT DIMENSIONS: 1.07 m x 0.78 m x 1.40 m

OD199537/2025-2026 Supply and Fixng of Health Walker including cost of materials, tools and labour complete.: All products must tested and certified to meet EN16630 safety standards with GS test mark. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The GS mark-EN 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors. The EN16630 & GS Mark certificates must reflect clearly on the notified certifying bodies websites. All products must clearly display the GS mark as has been issued in the EN16630 safety certificates. Upright structural posts of height 1.25 m is to be schedule HOT DIP Galvanized steel with a 114mm O.D. and 2.2mm (wall) thickness of the tubing. Two numbers of Foot Rest of size 361 mm x 161 mm are attached to the Standing Bars 957mm x 60 mm fabricated from 60 O.D. galvanized steel pipes. The poles are welded on to a base plate made from steel with 114mm inner diameter. An Internal limiter prevents the equipment from moving uncontrollably. Bearings : Maintenance-free ball bearings.Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. The limiters must be in accordance with EN16630 safety norms. Scope of delivery : 1 ompletely pre- assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. EQUIPMENT DIMENSIONS: 1.18 m x 0.553 m x 1.25m

OD199556/2025-2026 Supply and Fixng of Tai Chi Spinners including cost of materials, tools and labour complete.: All products must tested and certified to meet EN16630 safety standards with GS test mark. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The GS mark-EN 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors. The EN16630 & GS Mark certificates must reflect clearly on the notified certifying bodies websites. All products must clearly display the GS mark as has been issued in the EN16630 safety certificates. Upright structural posts of height 1.15 m is to be schedule HOT DIP Galvanized steel with a 114mm O.D. and 2.2mm (wall) thickness of the tubing. Circular Handrail of Dia 477 mm made with the pipe Dia of 32 mm fabricated from 32 O.D. galvanized steel pipes. The poles are welded on to a base plate made from steel with 114mm inner diameter. Bearings : Maintenance-free ball bearings. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. The limiters must be in accordance with EN16630 safety norms. Scope of delivery : 1 completely pre- assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. EQUIPMENT DIMENSIONS: 1.25 m x 1.09 m x 1.49 m

OD199567/2025-2026 Supply and Fixng of Rider including cost of materials, tools and labour complete.: All products must tested and certified to meet EN16630 safety standards with GS test mark. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The GS mark-EN 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors. The same must reflect clearly on the notified certifying bodies websites. All products must clearly display the GS mark as has been issued in the EN16630 safety certificates. Upright structural posts of height 0.5 m is to be schedule HOT DIP Galvanized steel with a 114mm O.D. and 2.2mm (wall) thickness of the tubing. A single seat of size 330 mm x 250 mm fixed to the top of the vertical post and two Pedals & Bars of size 145mm x 50 mm and Dia 38 mm fabricated from 40 O.D. galvanized steel pipes. The poles are welded on to a base plate made from steel with 114mm inner diameter. Bearings : Maintenance-free ball bearings. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. The limiters must be in accordance with EN16630 safety norms. Scope of delivery : 1 completely pre- assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. EQUIPMENT DIMENSIONS: 0.91 m x 0.65m x 1.27 m

OD199587/2025-2026 Supply & Fixing of KPSNK - 004 (thunder drums) including cost of materials, tools and labour complete.. All components designed and manufactured to meet with EN1176 safety standards. The EN 1176 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only.The thunder? drums refer to the well-known, classic drums used to beat out a rhythm. As a result, playing them is very intuitive and requires no additional skills. Up to three people can play these drums at the same time. You may want to add a bench for comfortable playing.The drums are available in three sizes which differ in diameter and colour of the surface on which you beat out the rhythm. You can have fun with sound and rhythm spontaneously playing just the drums or combining them with other instruments available in the playground. The instruments are comply with the European standard EN 1176, EN71.The safety of our products is confirmed by a TÜV SÜD Certificate.The instrument can be fixed to the ground with two anchoring systems Concrete anchor and Flat Anchor.All joints are Robotic welded. Dimensions LxWxH : 910 x 300 x 690 mm

OD200040/2025-2026 Moonwalker: Supply and Fixing of Moonwalker including cost of materials, tools and labour complete. All components designed and manufactured to meet with EN 1176 safety s The EN1176 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. Moonwalker is designed to be used seated, standing, or lying down. At wheelchair transfer height, the Moonwalker provides a supportive, dynamic experience. This is beneficial for those who may feel less confident or have less physical mobility. The textured Wetpour safety surfacing is impact absorbing for safer, more comfortable play. Each position challenges balance and coordination for all children, while encouraging social play.Galvanised powdercoated steel, Wetpour textured surface.Rotating, social, supportive movement.1300mm diameter disc, Wheelchair transfer height. Dimensions LxWxH : 1300 x 1204 mm

OD200044/2025-2026 INFINITY BOWL : Supply and Fixing of INFINITY BOWL including cost of materials, tools and labour complete. . All components designed and manufactured to meet with EN 1176 safety standards. The EN 1176 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only.The infinity bowl was designed to sit at an angle. This, paired with the dipped edge feature, allows ease of transfer. The deep bowl area provides supportive and comfortable seating for all users. The angle enables the bowl to self-propel. A child need only shift their weight slightly to get the bowl moving. The Infinity Bowl encourages both independence and cooperation when playing.Dipped access point, silver sparkle finish.Galvanised and Powder Coated steel bowl.Spinning, supportive movement, self propelled movement.All Joints are Robotic Welded. Dimensions LxWxH : 735 x 660 x 555 mm

OD200046/2025-2026 "Supply & Fixing of POD Swing: " The product to match the colours, design, size, contours and aesthetics exactly as per the image attached. "As per NIUA Guidlines all products must be tested and certified to meet EN 1176 safety standards. The EN 1176 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. An inverted ?U? Shaped structural posts of height 2.50 m are to be schedule HOT DIP Galvanized steel with a 114mm OD and 2.2mm (wall) thickness of the tubing. The poles are welded on to a base plate made from steel with 114mm inner diameter. At Top a metal sheet is provided which shall be an all-robotic welded unit, fabricated from galvanized steel pipes. Swing seats are all robotic welded fabricated The Electro- statically applied polyester powder has a tough finish with maximum durability. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 of tamper resistant stainless steel. Exposed hardware shall be covered with safety caps as per EN1176 standards. All joints are Robotic welded. PLAY EQUIPMENT DIMENSIONS: 2.83 x 1.30 x 2.50 m

OD200052/2025-2026 "KPSNK 005: Supply and Fixing of KPSNK 005 including cost of materials, tools and labour complete. All components designed and manufactured to meet with EN 1176 safety standards. The EN 1176 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only.The new HDPE play panels include different games, each with their own unique HDPE panel design. All panels are available in other colours or languages on request. The mounting holes must be drilled on installation. 3 IN A ROW- form three discs of your colour in a row in this classic game for two .Unique HDPE panel design.Solid HDPE material - thickness 19 mm. Available in other colours/languages on request.Mountingnting holes to be drilled depending on installation.All joints are Robotic welded. All components designed and manufactured to meet with EN1176 safety standards. Dimensions LxWxH : 735 x 735 mm "

OD200075/2025-2026 " Fiero A Swing: Supply and Fixing of Fiero A Swing including cost of materials, tools and labour complete.. All products must be tested and certified to meet EN 1176 safety standards. The EN 1176 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The EN 1176 certificates must be in the name of a supplier who has carried out in excess of atleast 100 public park projects in India either by themselves or through their dealers or contractors. These EN 1176 certificates must be clearly displayed on the notified certifying bodies websites as online verification is mandatory. Shaped structural posts of height 2.31 m are to be schedule HOT DIP Galvanized steel with a 114mm OD and 2.2mm (wall) thickness of the tubing. Plastic Components such as swing seats [super thick plastic] shall be animated and shall be rotationally molded from antistatic, copolymer, virgin linear low density UV stabilized polyethylene, with color molded in and minimum thickness of 6 - 8mm. All Joints are Robotic Welded. PLAY EQUIPMENT DIMENSIONS: 3.21 m x 1.54 m x 2.50 m"

OD200081/2025-2026 " 4 Seater See Saw: Supply and Fixing of 4 Seater See Saw including cost of materials, tools and labour complete.. All products must be tested and certified to meet EN 1176 safety standards. The EN 1176 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The EN 1176 certificates must be in the name of a supplier who has carried out in excess of at least 100 public park projects in India either by themselves or through their dealers or contractors. These EN 1176 certificates must be clearly displayed on the notified certifying bodies websites as online verification is mandatory. The See Saw consists of 2 poles of Dia 114mm and thickness of 2.5mm which balances the horizontal rod at the center which is of size 3110 mm length and Dia 114 mm. It consists of 4 seats which is made of LLDPE virgin plastic of size 305mm X 213 mm X 125 mm. All Joints are Robotic Welded PLAY EQUIPMENT DIMENSIONS: 3.10 m x 0.44 m x 0.80 m "

OD200133/2025-2026 "TRINITY - E: Supply & Fixing of TRINITY - E including cost of materials, tools and labour complete.: All products must be tested and certified to meet EN 1176 safety standards. The EN 1176 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only.Them EN1176 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. Deck of size 1.45 x 1.45m are fabricated from 2mm perforated solid punched steel. Deck perimeter is precision pre punched for attachments. Decks are pressed, punched, and welded sand blasted and vinyl plastic coated to a thickness of 4mm. Bent climber of size 0.87 m x 0.67 m x 0.90 m are fabricated from 2mm perforated solid punched steel. walls of Height 1.8 m are all robotic welded fabricated from 32 O.D. galvanized steel pipes for the outer pipes and 25mm O.D. Crab Roof of size 2.0 m x 1.77 m x 0.75 m, Straight Slide of size 1.66 m x 0.83 m x 0.90 m, Curved slide of size 1.65 m x 1.50 m x 0.90 m Tunnel of size 1.15 m x 0.99 m,Panels, Plastic Components [super thick plastic] shall be animated and shall be rotationally molded from antistatic, copolymer, virgin linear low density UV stabilized polyethylene, with color molded in and minimum thickness of 6 - 8mm. Stepping stones of size 1.82 m x 1.14 m x 0.60 m are all robotic welded fabricated from 48MM O.D. galvanized steel pipes Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 of tamper resistant stainless steel. Exposed hardware shall be covered with with safety caps. All joints are Robotic welded. PLAY EQUIPMENT DIMENSIONS: 6.02 x 5.10 x 3.40 m"

OD200136/2025-2026 " Challenger Course 1: Supply and Fixing of Challenger Course 1 including cost of materials, tools and labour complete.: Upright structural posts of height 0.55 m, 1.47 m , 1.55 m, 1.83 m, 2.0 m, 2.10 m, 2.36 m are to be schedule HOT DIP Galvanized steel with a 114mm OD and 2.2mm (wall) thickness of the tubing. Deck of size 1.16 m x 1.16 m, different levels of 0.3 m and 0.6 m shall be an all-PATENT welded assembly fabricated from perforated solid punched steel.Deck perimeter is precision pre punched for attachments. Decks are pre pressed, punched, and welded, powder coated to 2.2mm thickness or vinyl plastic coated to a thickness of 4mm. Handrail of height 1.09 m and Dia 32 mm. Support Legs of height 76 mm, 190 mm, 240 mm and Dia 32 mm. Toprails Of Monkey Bars of size 3 m x 1.04 m, Net climber of size 2.5 m x 1.02 m (2 Nos), Monkey loop of size 2.47 m x 1.05 m x 1.95 m (1Nos), Vertical Rope climber of size 2.6 m x 0.14 m (4 Nos), Semi circle of Balance beam ,2 Nos of Rope bridge comprise of ropes of Dia 16 mm, Rope obstacle of Semi circle, Wavey climber comprise of ropes of Dia 16 mm, Rope bridge comprise of ropes of Dia 16 mm are all robotic welded fabricated from 48MM O.D. galvanized steel pipes for the outer bars and 32 mm OD galvanized steel for the inner parallel bars. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 of tamper resistant stainless steel. Exposed hardware shall be covered with safety caps as per EN1176 standards. The poles are welded on to a base plate made from steel with 114mm inner diameter. Joints are robotic welded. All components conform to ENEST 1176 Safety Standards. PLAY EQUIPMENT DIMENSIONS: 18.59 m x 11.47 m x 2.75 m"

OD200139/2025-2026 " VANQUISH-E: Supply and fixing of childern Play Equipment Curved VANQUISH-E including cost of all materials, tools and labour complete. All products must be tested and certified to meet EN 1176 safety standards. The EN 1176 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. Curved structural posts of height 2.6 m, 3.0 m and 3.68 m are to be schedule HOT DIP Galvanized steel with a 114mm OD and 2.2mm (wall) thickness of the tubing. All post caps are to be cast from aluminum which is pretreated, cured and sandblasted, 114mm diameter, Handrail Dia 60 mm shall be an all-robotic welded unit, fabricated from galvanized steel pipes Twirl of size 3.0 m x 0.7 m, Stepping stones of size 2.8 m x 0.72 m, Twist net climber of size 2.75 m x 0.40 , Trigonal seat stone see saw of size 3.0 m x 0.36 m , Elliptical net climber of size 1.86 m and 8 shape hole climber are all robotic welded fabricated from 32 O.D. galvanized steel pipes Plastic Components [super thick plastic] shall be animated and shall be rotationally molded from antistatic, copolymer, virgin linear low density UV stabilized polyethylene, with color molded in and minimum thickness of 6 - 8mm. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 of tamper resistant stainless steel. Exposed hardware shall be covered with safety caps as per EN1176 standards. All joints are Robotic welded. PLAY EQUIPMENT DIMENSIONS: 9.82 m x 7.84 m x 3.68 m"

OD249639/2025-2026 Freight charge for supplying Gym and Play equipment , EPDM Rubber Flooring from a source to a destination place

OD249641/2025-2026 Installation of Gym and Play equipment as per the specification

Horticulture Works

2.31 Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared

30.2.1 Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

30.2.2 Supplying and stacking of good earth at site including royalty and carriage upto 5 k.m. lead complete (earth measured in stacks will be reduced by 20% for payment).

30.2.25 Supplying and stacking of well decayed cattle manure at site including royalty and carriage upto 5 k.m. lead complete (cattle manure measured in stacks will reduced by 8% for Payment).

30.2.4.1 Supplying and stacking at site dump manure from approved source, including carriage upto 5 k.m. lead complete (manure measured in stacks will be reduced by 8% for payment) :Screened through sieve of I.S. designation 20 mm

30.2.4.2 Screened through sieve of I.S. designation 16 mm Details of cost for one cum

30.2.4.3 Screened through sieve of I.S. designation 4.75 mm

30.2.5 Rough dressing the trenched ground including breaking clods

30.2.7 Fine dressing of the ground

30.2.8 Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

30.2.9 Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge

30.2.13 Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately).

30.2.14.1 Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) :Holes 1.2 m dia and 1.2 m deep

30.2.14.2 Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) :Holes 90 cm dia, and 90 cm deep

30.2.14.3 Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) :Holes 60 cm dia, and 60 cm deep

30.2.14.4 Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) :Holes 45 cm dia, and 45 cm deep

30.2.17.1 Making tree guard 53 cm dia and 1.3 m high as per design from empty coal tar drums, supplied free by the department, including providing and fixing 2 nos M.S. sheet rings 50 x 0.5 mm fixed with rivets complete in all respects including painting inside and outside of tree guard with:A coat of coal tar

30.2.28 Preparation of mounds of various size and shape by available excavated / supplied earth in layers not exceeding 20 cm in depth, breaking clods, watering of each layer, dressing etc., lead upto 50 meter and lift upto 1.5 m complete as per direction of Officer-in-charge.

30.2.57.1 Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unsaverieable material?s as per direction of officer in charge (excluding cast of plant & water )Cost of plantation per trees plants (for 100 nos.=427.45/100)

30.2.57.2 Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unsaverieable material?s as per direction of officer in charge (excluding cast of plant & water )Cost of plantation per Shrubs plants (for 200 nos.=427.45/200)

OD200248/2025-2026 Purchasing of Bauhinia purpurea (Kachnar) of plants height 150-165 cm. in big poly bags of plants size 25 cm

OD200254/2025-2026 Purchasing Ficus benjamina (green) of plants height 150-165 cm., bushy with healthy branchesand lush green foliage in big size HDPE bags

OD200261/2025-2026 Purchasing of Millingtonia hortensis of plants height 150-165 cm. in big poly bag of plants size 25cm

OD200270/2025-2026 Purchasing of Mimusops elengi (Maulsri) of plants height 180-195 cm., well developed with thick stem in big in big size HDPE bag

OD200280/2025-2026 Purchasing of Plumeria alba dwarf of plants height 90-105 cm. with 3-4 branches and thick stem in big size HDPE bags

OD200297/2025-2026 Purchasing Pongamia glabra (Papri) of plants height 120-135 cm. in big poly bag of plants size 25 cm

OD200323/2025-2026 Purchasing Saraca indica (Sita Ashok) of plants height 105-120 cm. in big poly bags of plants size 25 cm

OD200326/2025-2026 Purchasing of Tabebuia sp. of plants height 150-165 cm. in big polybags of plants size 25 cm

OD200329/2025-2026 Purchasing Acalypha red well developed with fresh & healthy 30 to 45 cm ht. plant in 20 cm size Earthen Pot/ Plastic Pot

OD200343/2025-2026 Purchasing of Alpinia Variegated (three in one) plant having ht. 30 cm and above, with fresh and healthy variegated foliage in 25 cm size of Earthen Pot / Plastic Pot

OD200369/2025-2026 Supply and stacking of plant Bauhinia acuminata height 60-75 cm. in earthen pots of size 20 cm

OD200372/2025-2026 Supply and stacking of plant Caesalpinia pulcherrima species of height 45-60 cm. in earthen pot of size 20 cm

OD200374/2025-2026 Clerodendron inerme plant of ht. 30 cm to 40 cm multi branched in 25 cm size of Earthen Pot / Plastic Pot.

OD200380/2025-2026 Providing of Dracaena fragrans?Massangeana?? plant, having ht. 30 cm & above with full of leaves, well developed, fresh and healthy in 25 cm size of Earthen pot / Plastic pot.

OD200392/2025-2026 Providing of Dracaena mahatma plant, having ht. 30 cm to 45 cm, well developed, fresh and healthy foliage in 20 cm size of Earthen pot / Plastic pot.

OD200396/2025-2026 Providing of Dracaena margineta plant, having ht. 30 cm to 45 cm with colourfull leaves, fresh and healthy in 20 cm size of Earthen pot / Plastic pot

OD200406/2025-2026 Supply and stacking of plant Excoecaria bicolor of height 45-60 cm. in earthen pots of size 20 cm

OD200407/2025-2026 Supply and stacking of plant Gardenia jasminoides of height 45-60 cm. with 3-4 branches in earthen pots of size 20 cm

OD200412/2025-2026 Supply and stacking of plant Hibiscus rosasinensis of height 90-105 cm., bushy in big size HDPE bag

OD200426/2025-2026 Jasminum grandiflorum (chameli) plant of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots

OD200434/2025-2026 Lagerstroemia thorelli of plants height 150-165 cm.in big poly bag of plants size 25cm

OD200444/2025-2026 Supply and stacking of plant Murraya exotica of height 45-60 cm. in poly bags of size 15 cm

OD200453/2025-2026 Putranjiva roxburghii of plants height 90-105 cm. in big polybag of plants size 25 cm

OD200461/2025-2026 Providing of Schefflera Green plant (three in one), mounted on moss stick 90 cm, well developed with full of fresh & healthy leaves from bottom to top with rich foliage in 25 cm size of Earthen pot / Plastic pot.

OD200463/2025-2026 Spathiphyllum (peace lilly), having 15 cm to 25 cm ht. blooming stag with fresh & healthy foliage well developed in 15 cm of Earthen pot/plastic pot

OD200467/2025-2026 Supply and stacking of plant Tabernaemontana coronaria (Chandni single) veriegated of height 105-120 cm., multibranched, bushy in big size HDPE bag

OD200472/2025-2026 Supply and stacking of plant Tabernaemontana coronaria (Chandni single) variegated of height 60-75 cm., 5-6 branches in p.bags of size 25 cm

OD200477/2025-2026 Ophiopogon jaburan ( variegated ) plant,full of variegated leaves in 20 cm Earthen Pot/Plastic Pot

OD200483/2025-2026 Providing of Philodendron sellum plant, having ht. 45 cm to 60 cm with 12 to 16 leaves, well developed, fresh and healthy foliage in 30 cm size of Earthen pot / Plastic pot.

OD200487/2025-2026 Providing of Philodendron ceylon gold plant, having ht. 30 cm to 45 cm with 8 to10 leaves, well developed, fresh & healthy bright colour leaves in 15 cm size of Earthen pot / Plastic pot.

OD200589/2025-2026 Wadelia trilobata plant,full of leaves in 15 cm size of Poly bags

OD200596/2025-2026 Providing of Areca Palm plant, having ht. 90 cm to 1.20 m with 4 to 5 suckers, well developed, fresh and healthy with lush green foliage in 20 cm size of Earthen pot / Plastic pot

OD200602/2025-2026 Providing of Raphis palm plant, having ht. 75 cm to 90 cm with 12 to 15 equal suckers, well developed, full of fresh & healthy leaves from bottom to top in 25 cm size Earthen pot / Plastic pot.

OD200608/2025-2026 Bamboo Buddha valley with fresh & healthy 3 to 4 suckers having 75 to 90 cm ht. plant in 25 cm size Earthen Pot/ Plastic Pot

Civil Work- Street Lights

2.8.1 Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

5.9.1 Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.22.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.1.2 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size derived from natural sources)

13.1.1 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

Electrical Works

90.15.3.1 Supply installation testing commissioning of Octogaonal Pole made of hot dip galvanised GI sheet 70mm top diameter, 130mm bottom diameter thickness 3mm base plate dimensions of 200x200x12mm suitable for wind speed as per IS 875 Part III single arm bracket 0.5mt including connector foundation bolt 4 nos fixed in existing RCC foundation and junctions box etc.complete 5 Meters

90.15.4.1 Supply Conveyance, installation, testing and commissioning of 20W LED street light] output greater than 105lumen/W 4000-6000 K with IP 66 protection LED Chip make Cree/Lumilled/Nichea with power factor greater than 0.95 at full load, internal surge protection up to 8 KV,and Aluminium pressure die-cast Powder coated housing,acrylic cover complete with THD Less than10%, power factor greater than 0.98, RoHS compliant, duly wired up for use on 230 V AC supply. Driver compartment should be seperatly accessible for maintenance (LM 79&80 certificates from NABL accredited Third party lab to be produced mentioning chip manufacturer)

90.6.5.11 Supply and drawing the following sizes of multi-core PVC insulated & FRLS PVC sheathed 650/1100 V grade copper conductor round flexible cables conforming to IS 694 part I 1960 in the existing surface / recess conduit as required including giving necessary connections of the following sizes.3 core 1.50 sq mm

5.1 Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal/ coke and salt ) as required.

90.12.1.12 Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil).3 core 4 sq mm

90.12.9.2 Supplying, laying and jointing of the following sizes of double wall corrugated (DWC) pipes made out of HDPE conforming to IS 14930 Part II for mechanical protection to underground power cables with all required accessories in ground in the existing trench50/38 mm or nearest size

2.10.3 Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, ""C"" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Double pole

2.12.1 Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

90.16.1.3 Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required3.15 mm copper conductor ( 10 SWG)

90.16.5.3 Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.3.15 mm (10 SWG)