CA NO.CWE BLY/GE (W)/50 OF 2026- 2027SPECIAL REPAIR TO OR GOVT MD ACCN QTR NO T-33 TO T-37 (05 QTRS) OR LINE AND QTR NO T-78 and T-79 (02 QTRS) GHARIYA LINE OF THE JAT REGT CENTRE BAREILLY UNDER GE (WEST) BAREILLY

M&L for non-skid ceremic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match of tiles and screed bed or bedding layer of mortar 15mm thick in cement mortar 1:6 for laying floor finishes incl dismanlting of existing flooring complete all as specified.

All as per serial item No 1 as above but as in vertical surfaces of tiles and rendering 10 mm thick in cement mortar 1:4, as in backing layer complete all as specified.

M&L for non- skid ceremic coloured tiles 7 to 8 mm thick (Square / rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match incl dismantling of tiles and screed bed or bedding layer of mortar 15mm thick in cement mortar 1:6 for laying floor finishes all as specified.

M&L for Glazed (plain /coloured) ceramic tiles wall 600x300x7mm thick on vertical faces of walls including 10mm thick rendeing in CM 1:4 set jointed in neat cement slurry and pointed in coloured cement to match including taking down old dado/skirting complete all as specified.

M&L for 20-25 mm thick machine cut pre polished kota stone slab as in flooring / shelves / platforms and jointed with grey cement slurry fixed with pigment to match to shade of the slab including rubbing and mirror polishing over and or 20 mm thick bedding layer of cement mortar 1:6 for laying floor finishes even and rough with and including dismantling floor, hearth or wall kota stone slab including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.

M&L for 20-25mm thick machine cut pre polished kota stone slab in riser of steps skirting, dado and pillar,landing in single piece with round nosing with three numbers of serration using as front door steps, laid over cement screed and jointed with grey cement slurry mixed with pigment to match including rubbing & mirror polishing ding and inclucding 10mm thick cement plaster on brick surfaces or concrete surface in cm (1:4) finished even and rough as screed dismantling of wall tile including cement mortar bedding complete all as spd and directed.

Taking down chowkats with shutters (without taking off shutters from the frames) area not exc 1.5 Sqm each including making good disturbed portions of wall with new or old bricks, lintel,cills, etc in CM 1:4 complete all as specified and directed.

Taking down chowkats with shutters (without taking off shutters from the frames) area exc 1.5 Sqm each and not exc. 4.00 Sqm including making good disturbed portions of wall with new or old bricks, lintel,cills, etc in CM 1:4 complete all as specified and directed.

S&F Fiber Glass Reinforced plastic (FRP) Door Frames of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminte shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame. complete as specified by the manufacturer and as per directions of Engineer-in-charge.

S&F 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table 3 of IS: 14856 complete all as specified by the manufacturer and as per directions of Engineer- in-charge.